3M Hard Hat L-705 with Welding Shield and Wide-view Faceshield and 3M Belt- Mounted Powered Air Purifying Respirator (PAPR) Assembly GVP-1

Transcription

1 3M Hard Hat L-705 with Welding Shield and Wide-view Faceshield and 3M Belt- Mounted Powered Air Purifying Respirator (PAPR) Assembly GVP-1 Welcome and thank you for choosing the 3M Hard Hat L-705 with Welding Shield and Wide-view Faceshield and 3M Belt-Mounted PAPR Assembly GVP-1. During this short review, we will be discussing how to configure your GVP-1 and L-705. The goal of this review is to show you how to maintain your system. We will cover replacement parts, cleaning and system assembly for this GVP-1 system. The L-705 will be covered in welding mode only. The instructions for converting it to a wide-view faceshield hard hat will be given but after that point the L-701 Instructions should be used. Please note that in some scenes headgear other than the L-705 will be shown, however, the processes for replacing parts are the same. Additional detailed information can be found in your User Instructions packaged with the product or by calling the 3M Technical Service Hotline at Double click picture to start video Click button to view video text This document has been encoded for a Windows operating system This version of the interactive document requires at minimum an internet connection with (256Kbs) minimum connection speed and Acrobat Reader 6.0 or higher for proper operation If there is no video, reaffirm that you are running Acrobat Reader 6.0 (minimum requirement) If video problems persist, try closing other applications that may be consuming the required memory If there is no audio or the volume is too low, right-click the audio setting icon and adjust accordingly Sound but no video, click NEXT Still having problems, call

2 Double click picture to start video Click button to view video text

3 Double click picture to start video Click button to view video text

4 3M L-705 Hardhat with GVP-1 GVP-1 Part No. Part Replace when: CB1000 Comfort Belt Ripped, torn, frayed or damaged GVP-100 Motor Blower Outside of the case is cracked GVP-101 Gasket Cracked or excessively worn GVP-110 Power Cord Damaged or missing GVP-111 Battery Pack Cracked, does not hold a charge or when the red battery light stays on for more than 20 minutes after connecting the battery to the charger. GVP-112 Battery Charger Red light does not come on when connected to the battery GVP-115 Plugs Damaged, worn or missing GVP-117 Urethane Belt Ripped, torn, frayed or damaged GVP-118 Urethane Shoulder Strap Ripped, torn, frayed or damaged GVP-119 Shower Cover Damaged or missing GVP-127 Web Belt Ripped, torn, frayed or damaged GVP-128 Web Shoulder Strap Ripped, torn, frayed or damaged GVP-146 Spark Arrest Cover Damaged or won

5 3M L-705 Hardhat with GVP-1 L-705 Part No. Part Description Replace when: L-113 Head Suspension Damaged or broken or the ratchet will not tighten L-114 Reinforced Chin Strap Torn, worn or damaged L-115 Sweat Pad Foam on the pad begins to degrade or the pad is dirty or damaged L-116 Head Pad Excessively dirty or damaged L-117 Hanger Suspension Damaged or missing Softguard Flame Retardant Faceseal L-120 Worn excessively or anytime it is torn L-122 Breathing Tube Punctures, cracks, holes or general wear are found L-124 Flame Retardant Seal Worn excessively or anytime it is torn L-129 Flame Retardant Welding Bib Worn excessively or anytime it is torn L-131 Wide View Lens for the L-705 Excessively scratched or anytime it is cracked, crazed or does not stay seated L-133 (10 or 100) Lens Cover Cover is dirty L-134 Latch Kit Latches are broken or missing. Do not use the headgear until the latches are in place L-135 Welding Shield Extender for the L- 703 Only replace when warped or unable to seal against the jaw. Do not remove for cleaning.

6 3M L-705 Hardhat with GVP-1 L-705 Part No. Part Description Replace when: L-136 Cam Spring Set for the L-705 The Cam Spring Set should be replaced when the faceshield will no longer stay in the up or down position or when the faceshield is loose in the closed position. The Springs should not be removed for cleaning. L-142 Welding Gasket (welding stack) Damaged or missing L-145 Welding Knob Worn or missing L-146 Welding Knob and Pivot Set Damaged or missing L-147 Welding Lens Retainer Clip Damaged or missing L-149 Fiber Gasket Spacer (welding stack) Damaged or missing L-152 Cover Plate (welding stack) Damaged or missing L-153 Welding Shield for the L-705 Damaged L-156 Electronic Lens Damaged or missing L-162 Safety Plate (welding stack) Damaged or missing Parts are missing or the Liner is damaged by L-163 Foam Liner exposure to solvents or excessive heat L-182 Air Deflector Damaged or missing L-183 Headgear Cover is ripped, torn, the stitching is worn, the seams are frayed or holes are found in it L-750 Hard Hat Shell Cracked or damaged by contact with solvents

7 For more information, please contact: Use of these products by untrained or unqualified persons, or use not in accordance with the instructions, may adversely affect product performance and result in sickness or death. These products are to be used only by qualified persons who are properly trained in their use and maintenance, and only in accordance with their operating and maintenance manuals. Each person using these products must first read and understand the operators manual. For proper use, see your supervisor, product instructions and warnings or call 3M OH &ESD Technical Service at In Canada call extension # 613 3M Occupational Health and Environmental Safety Division (OH&ESD) In the U.S., contact: Sales Assistance Technical Assistance Fax On Demand Internet For other 3M products M HELPS In Canada, contact: 3M Canada Company, OH&ESD P.O. Box 5757 London, Ontario N6A 4T1 Sales Assistance , ext Technical Assistance (Canada only) Fax On Demand Internet Technical Assistance In Mexico , (Mexico City only) Technical Assistance In Brazil Fax On Demand O.U.S.Locations M Occupational Health and Environmental Safety Division 3M Center, Building 235-2W-70 St. Paul, MN M June All rights reserved.