BS EN 485-2:2007 Ntionl foreword This British Stndrd ws published by BSI. It is the UK implementtion of EN 485-2:2007. It supersedes B
|
|
- Georgia Knight
- 6 years ago
- Views:
Transcription
1 BRITISH STANDARD BS EN 485-2:2007 Aluminium nd luminium lloys Sheet, strip nd plte Prt 2: Mechnicl properties The Europen Stndrd EN 485-2:2007 hs the sttus of British Stndrd ICS
2 BS EN 485-2: Ntionl foreword This British Stndrd ws published by BSI. It is the UK implementtion of EN 485-2:2007. It supersedes BS EN 485-2:2004 which is withdrwn. The UK prticiption in its preprtion ws entrusted to Technicl Committee NFE/35, Light metls nd their lloys. A list of orgniztions represented on this committee cn be obtined on request to its secretry. This publiction does not purport to include ll the necessry provisions of contrct. Users re responsible for its correct ppliction. Complince with British Stndrd cnnot confer immunity from legl obligtions. This British Stndrd ws published under the uthority of the Stndrds Policy nd Strtegy Committee on 30 April 2007 Amendments issued since publiction Amd. No. Dte Comments BSI 2007 ISBN
3 EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN April 2007 ICS Supersedes EN 485-2:2004 English Version Aluminium nd luminium lloys - Sheet, strip nd plte - Prt 2: Mechnicl properties Aluminium et lliges d'luminium - Tôles, bndes et tôles épisses - Prtie 2: Crctéristiques mécniques Aluminium und Aluminiumlegierungen - Bänder, Bleche und Pltten - Teil 2: Mechnische Eigenschften This Europen Stndrd ws pproved by CEN on 28 Februry CEN members re bound to comply with the CEN/CENELEC Internl Regultions which stipulte the conditions for giving this Europen Stndrd the sttus of ntionl stndrd without ny ltertion. Up-to-dte lists nd bibliogrphicl references concerning such ntionl stndrds my be obtined on ppliction to the CEN Mngement Centre or to ny CEN member. This Europen Stndrd exists in three officil versions (English, French, Germn). A version in ny other lnguge mde by trnsltion under the responsibility of CEN member into its own lnguge nd notified to the CEN Mngement Centre hs the sme sttus s the officil versions. CEN members re the ntionl stndrds bodies of Austri, Belgium, Bulgri, Cyprus, Czech Republic, Denmrk, Estoni, Finlnd, Frnce, Germny, Greece, Hungry, Icelnd, Irelnd, Itly, Ltvi, Lithuni, Luxembourg, Mlt, Netherlnds, Norwy, Polnd, Portugl, Romni, Slovki, Sloveni, Spin, Sweden, Switzerlnd nd United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG Mngement Centre: rue de Stssrt, 36 B-1050 Brussels 2007 CEN All rights of exploittion in ny form nd by ny mens reserved worldwide for CEN ntionl Members. Ref. No. EN 485-2:2007: E
4 EN 485-2:2007 (E) Contents Pge Foreword Scope Normtive references Requirements List of lloys with mechnicl property limits Generl List of lloys nd their mechnicl properties...5 Annex A (normtive) Rules for rounding...63 Annex B (informtive) Explntion of temper designtions used in Tbles 1 to 46 bsed on definitions of EN Bibliogrphy
5 EN 485-2:2007 (E) Foreword This document (EN 485-2:2007) hs been prepred by Technicl Committee CEN/TC 132 Aluminium nd luminium lloys, the secretrit of which is held by AFNOR. This Europen Stndrd shll be given the sttus of ntionl stndrd, either by publiction of n identicl text or by endorsement, t the ltest by October 2007, nd conflicting ntionl stndrds shll be withdrwn t the ltest by October This document supersedes EN 485-2:2004. Within its progrmme of work, Technicl Committee CEN/TC 132 entrusted CEN/TC 132/WG 7 "Sheet, strip nd plte" to revise EN 485-2:2004. EN 485 comprises the following prts under the generl tittle, "Aluminium nd luminium lloys Sheet, strip nd plte". Prt 1: Technicl conditions for inspection nd delivery Prt 2: Mechnicl properties Prt 3: Tolernces on dimensions nd form for hot-rolled products Prt 4: Tolernces on shpe nd dimensions for cold-rolled products Besides very slight editoril djustments in the text nd updte of normtive references, the following technicl chnges hve been mde: Cluses 3 to 9: Hve been moved to pren Tbles 1 to 46: New lloys: Due to the introduction of new lloys, the tbles hve been renumbered when necessry. EN AW-2618A; EN AW-5010; EN AW-5026; EN AW-5059; EN AW-5070; EN AW- 5088; EN AW-6025; EN AW-7010 dded. Attention is drwn to the possibility tht some of the elements of this document my be the subject of ptent rights. CEN shll not be held responsible for identifying ny or ll such ptent rights. CEN/TC 132 ffirms it is its policy tht in the cse when ptentee refuses to grnt licences on stndrdised stndrd products under resonble nd not discrimintory conditions then this product shll be removed from the corresponding stndrd. According to the CEN/CENELEC Internl Regultions, the ntionl stndrds orgniztions of the following countries re bound to implement this Europen Stndrd: Austri, Belgium, Bulgri, Cyprus, Czech Republic, Denmrk, Estoni, Finlnd, Frnce, Germny, Greece, Hungry, Icelnd, Irelnd, Itly, Ltvi, Lithuni, Luxembourg, Mlt, Netherlnds, Norwy, Polnd, Portugl, Romni, Slovki, Sloveni, Spin, Sweden, Switzerlnd nd United Kingdom. 3
6 EN 485-2:2007 (E) 1 Scope This document specifies the mechnicl properties of wrought luminium nd wrought luminium lloy sheet, strip nd plte for generl engineering pplictions. It does not pply to semi-finished rolled products in coiled form to be subjected to further rolling (reroll stock) or to specil products such s corrugted, embossed, pinted, sheets nd strips or to specil pplictions such s erospce, cn stock, finstock, for which mechnicl properties re specified in seprte Europen Stndrds. The chemicl composition limits of the lloys re specified in EN designtions re defined in Annex B, in complince with the provisions of EN Normtive references The following referenced documents re indispensble for the ppliction of this document. For dted references, only the edition cited pplies. For undted references, the ltest edition of the referenced document (including ny mendments) pplies. pren 485-1, Aluminium nd luminium lloys Sheet, strip nd plte Prt 1: Technicl conditions for inspection nd delivery EN , Metllic mterils Tensile testing Prt 1: Method of test t mbient temperture ASTM G66, Visul Assessment of Exfolition Corrosion Susceptibility of 5xxx Series Aluminium Alloys (ASSET test) ASTM G67, Stndrd Test Method for Determining the Susceptibility to Intergrnulr Corrosion of 5xxx series Aluminium Alloys by mss loss fter exposure to nitric cid (NAMLT test) 3 Requirements The mechnicl properties shll be in conformity with those specified in Cluse 4 or those greed upon between purchser nd mnufcturer nd stted on order document. 4 List of lloys with mechnicl property limits 4.1 Generl Tbles 1 to 46 contin mechnicl property limits vlues obtined by tensile testing ccording to EN fter smpling nd fter smple preprtion ccording to pren They lso contin vlues of bend rdius nd hrdness following smpling nd test methods s described in pren These vlues re for informtion only. For some lloys they contin provisions relted to intergrnulr corrosion, exfolition corrosion or stress corrosion testing, see lso pren
7 EN 485-2:2007 (E) 4.2 The A 50mm vlue is the elongtion mesured over guge length of 50 mm nd expressed in percent. The A vlue for elongtion is the elongtion mesured over guge length of 5,65 cross-sectionl re of the test-piece), nd expressed in percent. 4.3 List of lloys nd their mechnicl properties S o (where S o is the initil Pge Tble 1 Aluminium EN AW-1050A [Al 99,5] 7 Tble 2 Aluminium EN AW-1070A [Al 99,7] 9 Tble 3 Aluminium EN AW-1080A [Al 99,8(A)] 10 Tble 4 Aluminium EN AW-1200 [Al 99,0] 11 Tble 5 Alloy EN AW-2014 [Al Cu4SiMg] 13 Tble 6 Alloy EN AW-2014A [Al Cu4SiMg(A)] 14 Tble 7 Alloy EN AW-2017A [Al Cu4MgSi(A)] 15 Tble 8 Alloy EN AW-2024 [Al Cu4Mg1] 16 Tble 9 Alloy EN AW-2618A [Al Cu2Mg1,5Ni] 17 Tble 10 Alloy EN AW-3003 [Al Mn1Cu] 18 Tble 11 Alloy EN AW-3004 [Al Mn1Mg1] 20 Tble 12 Alloy EN AW-3005 [Al Mn1Mg0,5] 21 Tble 13 Alloy EN AW-3103 [Al Mn1] 22 Tble 14 Alloy EN AW-3105 [Al Mn0,5Mg0,5] 24 Tble 15 Alloy EN AW-4006 [Al Si1Fe] 25 Tble 16 Alloy EN AW-4007 [Al Si1,5Mn] 26 Tble 17 Alloy EN AW-4015 [Al Si2Mn] 26 Tble 18 Alloy EN AW-5005 [Al Mg1(B)], lloy EN AW-5005A [Al Mg1(C)] 27 Tble 19 Alloy EN AW-5010 [ AlMg 0,5Mn] 29 Tble 20 Alloy EN AW-5026 [AI Mg4,5 MnSiFe] 30 Tble 21 Alloy EN AW-5040 [Al Mg1,5Mn] 30 Tble 22 Alloy EN AW-5049 [Al Mg2Mn0,8] 31 Tble 23 Alloy EN AW-5050 [Al Mg1,5(C)] 33 5
8 EN 485-2:2007 (E) Tble 24 Alloy EN AW-5052 [Al Mg2,5] 35 Tble 25 Alloy EN AW-5059 [Al Mg5,5MnZnZr] 36 Tble 26 Alloy EN AW-5070 [Al Mg4MnZn] 37 Tble 27 Alloy EN AW-5083 [Al Mg4,5Mn0,7] 38 Tble 28 Alloy EN AW-5086 [Al Mg4] 40 Tble 29 Alloy EN AW-5088 [AlMg5Mn0,4] 41 Tble 30 Alloy EN AW-5154A [Al Mg3,5(A)] 42 Tble 31 Alloy EN AW-5182 [Al Mg4,5Mn0,4] 44 Tble 32 Alloy EN AW-5251 [Al Mg2] 45 Tble 33 Alloy EN AW-5383 [Al Mg4,5Mn0,9] 47 Tble 34 Alloy EN AW-5449 [Al Mg2Mn0,8(B)] 48 Tble 35 Alloy EN AW-5454 [Al Mg3Mn] 49 Tble 36 Alloy EN AW-5754 [Al Mg3] 51 Tble 37 Alloy EN AW-6016 [Al Si1,2Mg0,4] 53 Tble 38 Alloy EN AW-6025 [Al Mg2,5SiMnCu] 53 Tble 39 Alloy EN AW-6061 [Al Mg1SiCu] 54 Tble 40 Alloy EN AW-6082 [Al Si1MgMn] 55 Tble 41 Alloy EN AW-7010 [Al Zn6MgCu] 56 Tble 42 Alloy EN AW-7020 [Al Zn4,5Mg1] 58 Tble 43 Alloy EN AW-7021 [Al Zn5,5Mg1,5] 59 Tble 44 Alloy EN AW-7022 [Al Zn5Mg3Cu] 59 Tble 45 Alloy EN AW-7075 [Al Zn5,5MgCu] 60 Tble 46 Alloy EN AW-8011A [Al FeSi(A)] 62 6
9 EN 485-2:2007 (E) Tble 1 Aluminium EN AW-1050A [Al 99,5] HBW over up to mx. mx. A 50 mm F 2,5 150,0 60 O/H111 0,2 0, t 0 t 20 0,5 1, t 0 t 20 1,5 3, t 0 t 20 3,0 6, ,5 t 0,5 t 20 6,0 12, ,0 t 1,0 t 20 12,5 80, H112 6,0 12, ,5 80, H12 0,2 0, ,5 t 0 t 28 0,5 1, ,5 t 0 t 28 1,5 3, ,5 t 0,5 t 28 3,0 6, ,0 t 1,0 t 28 6,0 12, ,0 t 28 12,5 40, H14 0,2 0, ,0 t 0 t 34 0,5 1, ,0 t 0,5 t 34 1,5 3, ,0 t 1,0 t 34 3,0 6, ,5 t 34 6,0 12, ,5 t 34 12,5 25, H16 0,2 0, ,5 t 39 0,5 1, ,0 t 39 1,5 4, ,5 t 39 H18 0,2 0, ,0 t 42 0,5 1, ,0 t 42 1,5 3, ,0 t 42 H19 0,2 0, ,5 1, ,5 3, H22 0,2 0, ,5 t 0 t 27 0,5 1, ,5 t 0 t 27 1,5 3, ,5 t 0,5 t 27 3,0 6, ,0 t 1,0 t 27 6,0 12, ,0 t 27 7
10 EN 485-2:2007 (E) Tble 1 (continued) HBW over up to mx. mx. A 50 mm H24 0,2 0, ,0 t 0 t 33 0,5 1, ,0 t 0,5 t 33 1,5 3, ,0 t 1,0 t 33 3,0 6, ,5 t 1,5 t 33 6,0 12, ,5 t 33 H26 0,2 0, ,5 t 38 0,5 1, ,0 t 38 1,5 4, ,5 t 38 H28 0,2 0, ,0 t 41 0,5 1, ,0 t 41 1,5 3, ,0 t 41 For informtion only. 8
11 EN 485-2:2007 (E) Tble 2 Aluminium EN AW-1070A [Al 99,7] over up to mx. mx. A 50 mm HBW F 2,5 25,0 60 O/H111 0,2 0, t 0 t 18 0,5 1, t 0 t 18 1,5 3, t 0 t 18 3,0 6, ,5 t 0,5 t 18 6,0 12, ,5 t 0,5 t 18 12,5 25, H112 6,0 12, ,5 25, H12 0,2 0, ,5 t 0 t 26 0,5 1, ,5 t 0 t 26 1,5 3, ,5 t 0,5 t 26 3,0 6, ,0 t 26 6,0 12, ,0 t 26 H14 0,2 0, ,5 t 0 t 32 0,5 1, ,5 t 0,5 t 32 1,5 3, ,0 t 1,0 t 32 3,0 6, ,5 t 32 6,0 12, ,5 t 32 H16 0,2 0, ,0 t 0,5 t 36 0,5 1, ,0 t 1,0 t 36 1,5 4, ,0 t 1,0 t 36 H18 0,2 0, ,0 t 40 0,5 1, ,0 t 40 1,5 3, ,5 t 40 H22 0,2 0, ,5 t 0 t 26 0,5 1, ,5 t 0 t 26 1,5 3, ,5 t 0,5 t 26 3,0 6, ,0 t 26 6,0 12, ,0 t 26 H24 0,2 0, ,5 t 0 t 31 0,5 1, ,5 t 0,5 t 31 1,5 3, ,0 t 1,0 t 31 3,0 6, ,5 t 31 6,0 12, ,5 t 31 H26 0,2 0, ,5 t 35 0,5 1, ,0 t 35 1,5 4, ,0 t 35 For informtion only. 9
12 EN 485-2:2007 (E) Tble 3 Aluminium EN AW-1080A [Al 99,8(A)] over up to mx. mx. A 50 mm HBW F 2,5 25,0 60 O/H111 0,2 0, t 0 t 18 0,5 1, t 0 t 18 1,5 3, t 0 t 18 3,0 6, ,5 t 0,5 t 18 6,0 12, ,5 t 0,5 t 18 H112 6,0 12, ,5 25, H12 0,2 0, ,5 t 0 t 26 0,5 1, ,5 t 0 t 26 1,5 3, ,5 t 0,5 t 26 3,0 6, ,0 t 26 6,0 12, ,0 t 26 H14 0,2 0, ,5 t 0 t 32 0,5 1, ,5 t 0,5 t 32 1,5 3, ,0 t 1,0 t 32 3,0 6, ,5 t 32 6,0 12, ,5 t 32 H16 0,2 0, ,0 t 0,5 t 36 0,5 1, ,0 t 1,0 t 36 1,5 4, ,0 t 1,0 t 36 H18 0,2 0, ,0 t 40 0,5 1, ,0 t 40 1,5 3, ,5 t 40 H22 0,2 0, ,5 t 0 t 26 0,5 1, ,5 t 0 t 26 1,5 3, ,5 t 0,5 t 26 3,0 6, ,0 t 26 6,0 12, ,0 t 26 H24 0,2 0, ,5 t 0 t 31 0,5 1, ,5 t 0,5 t 31 1,5 3, ,0 t 1,0 t 31 3,0 6, ,5 t 31 6,0 12, ,5 t 31 H26 0,2 0, ,5 t 35 0,5 1, ,0 t 35 1,5 4, ,0 t 35 For informtion only. 10
13 EN 485-2:2007 (E) Tble 4 Aluminium EN AW-1200 [Al 99,0] over up to mx. mx. A 50 mm HBW F 2,5 150,0 75 O/H111 0,2 0, t 0 t 23 0,5 1, t 0 t 23 1,5 3, t 0 t 23 3,0 6, ,5 t 0,5 t 23 6,0 12, ,0 t 1,0 t 23 12,5 80, H112 6,0 12, ,5 80, H12 0,2 0, ,5 t 0 t 31 0,5 1, ,5 t 0 t 31 1,5 3, ,5 t 0,5 t 31 3,0 6, ,0 t 1,0 t 31 6,0 12, ,0 t 31 12,5 40, H14 0,2 0, ,0 t 0 t 37 0,5 1, ,0 t 0,5 t 37 1,5 3, ,0 t 1,0 t 37 3,0 6, ,5 t 1,5 t 37 6,0 12, ,5 t 37 12,5 25, H16 0,2 0, ,5 t 42 0,5 1, ,0 t 42 1,5 4, ,5 t 42 H18 0,2 0, ,0 t 45 0,5 1, ,0 t 45 1,5 3, ,0 t 45 H19 0,2 0, ,5 1, ,5 3,
14 EN 485-2:2007 (E) Tble 4 (continued) over up to mx. mx. A 50 mm HBW H22 0,2 0, ,5 t 0 t 30 0,5 1, ,5 t 0 t 30 1,5 3, ,5 t 0,5 t 30 3,0 6, ,0 t 1,0 t 30 6,0 12, ,0 t 30 H24 0,2 0, ,0 t 0 t 37 0,5 1, ,0 t 0,5 t 37 1,5 3, ,0 t 1,0 t 37 3,0 6, ,5 t 37 6,0 12, ,5 t 36 H26 0,2 0, ,5 t 41 0,5 1, ,0 t 41 1,5 4, ,5 t 41 For informtion only. 12
15 EN 485-2:2007 (E) Tble 5 Alloy EN AW-2014 [Al Cu4SiMg] over up to mx. mx. A 50 mm O 0,4 1, ,5 t 0 t 55 1,5 3, ,0 t 1,0 t 55 3,0 6, ,5 t 55 6,0 9, ,5 t 55 9,0 12, ,0 t 55 12,5 25, T3 0,4 1, ,5 6, T4 0,4 1, ,0 t b 3,0 t b 110 T451 1,5 6, ,0 t b 5,0 t b 110 6,0 12, ,0 t b ,5 40, ,0 100, T42 0,4 6, ,0 12, ,5 25, T6 0,4 1, ,0 t b 133 T651 1,5 6, ,0 t b 133 6,0 12, t b ,5 40, ,0 60, ,0 80, ,0 100, ,0 125, ,0 160, T62 0,4 12, ,5 25, HBW Whenever new ppliction of this lloy is contemplted, nd if this ppliction involves specil properties such s corrosion resistnce, toughness, ftigue strength, it is strongly recommended tht the user consult the producer in order to mke precise nd pproprite selection of the mteril. b For informtion only. Apprecibly smller cold bend rdii cn be chieved immeditely fter quenching. 13
16 EN 485-2:2007 (E) Tble 6 Alloy EN AW-2014A [Al Cu4SiMg(A)] HBW over up to mx. mx. A 50 mm O 0,2 0, ,0 t 55 0,5 1, ,0 t 55 1,5 3, ,0 t 55 3,0 6, ,0 t 55 T4 0,2 0, ,0 t b 110 T451 0,5 1, ,0 t b 110 1,5 6, ,0 t b 110 6,0 12, ,5 25, ,0 40, ,0 80, T6 0,2 0, ,0 t b 150 T651 0,5 1, ,0 t b 150 1,5 3, ,0 t b 150 3,0 6, ,0 t b 150 6,0 12, ,5 25, ,0 40, ,0 60, ,0 90, ,0 115, ,0 140, Whenever new ppliction of this lloy is contemplted, nd if this ppliction involves specil properties such s corrosion resistnce, toughness, ftigue strength, it is strongly recommended tht the user consult the producer in order to mke precise nd pproprite selection of the mteril. b For informtion only. Apprecibly smller cold bend rdii cn be chieved immeditely fter quenching. 14
17 EN 485-2:2007 (E) Tble 7 Alloy EN AW-2017A [Al Cu4MgSi(A)] HBW over up to mx. mx. A 50 mm O 0,4 1, ,5 t 0 t 55 1,5 3, ,0 t 1,0 t 55 3,0 6, ,5 t 55 6,0 9, ,5 t 55 9,0 12, ,0 t 55 12,5 25, T4 0,4 1, ,0 t b 3,0 t b 110 T451 1,5 6, ,0 t b 5,0 t b 110 6,0 12, ,0 t b ,5 40, ,0 60, ,0 80, ,0 120, ,0 150, ,0 180, ,0 200, T ,0 180, ,0 200, T42 0,4 3, ,0 12, ,5 25, Whenever new ppliction of this lloy is contemplted, nd if this ppliction involves specil properties such s corrosion resistnce, toughness, ftigue strength, it is strongly recommended tht the user consult the producer in order to mke precise nd pproprite selection of the mteril. b For informtion only. Apprecibly smller cold bend rdii cn be chieved immeditely fter quenching. 15
18 EN 485-2:2007 (E) Tble 8 Alloy EN AW-2024 [Al Cu4Mg1] over up to mx. mx. A 50 mm HBW O 0,4 1, ,5 t 0 t 55 1,5 3, ,0 t 1,0 t 55 3,0 6, ,0 t 1,5 t 55 6,0 9, ,5 t 55 9,0 12, ,0 t 55 12,5 25, T4 0,4 1, ,0 t 120 1,5 6, ,0 t 120 T3 0,4 1, ,0 t b 4,0 t b 123 T351 1,5 3, ,0 t b 4,0 t b 123 3,0 6, ,0 t b 5,0 t b 124 6,0 12, ,0 t b ,5 40, ,0 80, ,0 100, ,0 120, ,0 150, T42 0,4 6, ,0 12, ,5 25, T8 0,4 1, T851 1,5 6, ,0 12, ,5 25, ,0 40, T62 0,4 12, ,5 25, Whenever new ppliction of this lloy is contemplted, nd if this ppliction involves specil properties such s corrosion resistnce, toughness, ftigue strength, it is strongly recommended tht the user consult the producer in order to mke precise nd pproprite selection of the mteril. b For informtion only. Apprecibly smller cold bend rdii cn be chieved immeditely fter quenching. 16
19 EN 485-2:2007 (E) Tble 9 Alloy EN AW-2618A [Al Cu2Mg1,5Ni] over up to mx. mx. A 50 mm HBW T851 > 6,0 12, ,5 40, ,0 80, ,0 100, ,0 140, No dt vilble. 17
20 EN 485-2:2007 (E) Tble 10 Alloy EN AW-3003 [Al Mn1Cu] HBW over up to mx. mx. A 50 mm F 2,5 80,0 95 O/H111 0,2 0, t 0 t 28 0,5 1, t 0 t 28 1,5 3, t 0 t 28 3,0 6, ,0 t 1,0 t 28 6,0 12, ,5 t 28 12,5 50, H112 6,0 12, ,5 80, H12 0,2 0, ,5 t 0 t 38 0,5 1, ,5 t 0,5 t 38 1,5 3, ,5 t 1,0 t 38 3,0 6, ,0 t 38 6,0 12, ,0 t 38 12,5 40, H14 0,2 0, ,0 t 0,5 t 46 0,5 1, ,0 t 1,0 t 46 1,5 3, ,0 t 1,0 t 46 3,0 6, ,0 t 46 6,0 12, ,5 t 46 12,5 25, H16 0,2 0, ,5 t 1,0 t 54 0,5 1, ,5 t 1,5 t 54 1,5 4, ,5 t 2,0 t 54 H18 0,2 0, ,5 t 60 0,5 1, ,5 t 60 1,5 3, ,0 t 60 H19 0,2 0, ,5 1, ,5 3, H22 0,2 0, ,0 t 0 t 37 0,5 1, ,0 t 0,5 t 37 1,5 3, ,0 t 1,0 t 37 3,0 6, ,0 t 37 6,0 12, ,0 t 37 18
21 EN 485-2:2007 (E) Tble 10 (continued) HBW over up to mx. mx. A 50 mm H24 0,2 0, ,5 t 0,5 t 45 0,5 1, ,5 t 1,0 t 45 1,5 3, ,5 t 1,0 t 45 3,0 6, ,0 t 45 6,0 12, ,5 t 45 H26 0,2 0, ,0 t 1,0 t 53 0,5 1, ,0 t 1,5 t 53 1,5 4, ,0 t 2,0 t 53 H28 0,2 0, ,5 t 59 0,5 1, ,5 t 59 1,5 3, ,0 t 59 For informtion only. 19
22 EN 485-2:2007 (E) Tble 11 Alloy EN AW-3004 [Al Mn1Mg1] over up to mx. mx. A 50 mm HBW F 2,5 80,0 155 O/H111 0,2 0, t 0 t 45 0,5 1, t 0 t 45 1,5 3, ,5 t 0 t 45 3,0 6, ,0 t 1,0 t 45 6,0 12, ,0 t 45 12,5 50, H12 0,2 0, ,5 t 0 t 59 0,5 1, ,5 t 0,5 t 59 1,5 3, ,0 t 1,0 t 59 3,0 6, ,5 t 59 H14 0,2 0, ,5 t 0,5 t 67 0,5 1, ,5 t 1,0 t 67 1,5 3, ,5 t 1,5 t 67 3,0 6, ,0 t 67 H16 0,2 0, ,5 t 1,0 t 73 0,5 1, ,5 t 1,5 t 73 1,5 4, ,5 t 73 H18 0,2 0, ,5 t 80 0,5 1, ,5 t 80 1,5 3, H19 0,2 0, ,5 1, H22/H32 0,2 0, ,0 t 0 t 58 0,5 1, ,0 t 0,5 t 58 1,5 3, ,5 t 1,0 t 58 3,0 6, ,5 t 58 H24/H34 0,2 0, ,0 t 0,5 t 66 0,5 1, ,0 t 1,0 t 66 1,5 3, ,0 t 1,5 t 66 H26/H36 0,2 0, ,0 t 1,0 t 72 0,5 1, ,0 t 1,5 t 72 1,5 3, ,5 t 72 H28/H38 0,2 0, ,5 t 79 0,5 1, ,5 t 79 For informtion only. 20
23 EN 485-2:2007 (E) Tble 12 Alloy EN AW-3005 [Al Mn1Mg0,5] over up to mx. mx. A 50 mm HBW F 2,5 80,0 115 O/H111 0,2 0, t 0 t 33 0,5 1, t 0 t 33 1,5 3, ,0 t 0,5 t 33 3,0 6, ,0 t 33 H12 0,2 0, ,5 t 0 t 46 0,5 1, ,5 t 0,5 t 46 1,5 3, ,0 t 1,0 t 46 3,0 6, ,5 t 46 H14 0,2 0, ,5 t 0,5 t 54 0,5 1, ,5 t 1,0 t 54 1,5 3, ,5 t 54 3,0 6, ,0 t 54 H16 0,2 0, ,0 t 61 0,5 1, ,5 t 61 1,5 4, ,5 t 61 H18 0,2 0, ,5 t 69 0,5 1, ,5 t 69 1,5 3, H19 0,2 0, ,5 1, H22 0,2 0, ,0 t 0 t 45 0,5 1, ,0 t 0,5 t 45 1,5 3, ,5 t 1,0 t 45 3,0 6, ,5 t 45 H24 0,2 0, ,5 t 0,5 t 52 0,5 1, ,5 t 1,0 t 52 1,5 3, ,5 t 52 H26 0,2 0, ,0 t 60 0,5 1, ,5 t 60 1,5 3, ,5 t 60 H28 0,2 0, ,5 t 68 0,5 1, ,5 t 68 1,5 3, For informtion only. 21
24 EN 485-2:2007 (E) Tble 13 Alloy EN AW-3103 [Al Mn1] over up to mx. mx. A 50 mm HBW F 2,5 80,0 90 O/H111 0,2 0, t 0 t 27 0,5 1, t 0 t 27 1,5 3, t 0 t 27 3,0 6, ,0 t 1,0 t 27 6,0 12, ,5 t 27 12,5 50, H112 6,0 12, ,5 80, H12 0,2 0, ,5 t 0 t 36 0,5 1, ,5 t 0,5 t 36 1,5 3, ,5 t 1,0 t 36 3,0 6, ,0 t 36 6,0 12, ,0 t 36 12,5 40, H14 0,2 0, ,0 t 0,5 t 45 0,5 1, ,0 t 1,0 t 45 1,5 3, ,0 t 1,0 t 45 3,0 6, ,0 t 45 6,0 12, ,5 t 45 12,5 25, H16 0,2 0, ,5 t 1,0 t 51 0,5 1, ,5 t 1,5 t 51 1,5 4, ,5 t 2,0 t 51 4,0 8, ,0 t 1,5 t 51 H18 0,2 0, ,5 t 58 0,5 1, ,5 t 58 1,5 3, ,0 t 58 H19 0,2 0, ,5 1, ,5 3, H22 0,2 0, ,0 t 0 t 36 0,5 1, ,0 t 0,5 t 36 1,5 3, ,0 t 1,0 t 36 3,0 6, ,0 t 36 6,0 12, ,0 t 36 22
25 EN 485-2:2007 (E) Tble 13 (continued) over up to mx. mx. A 50 mm HBW H24 0,2 0, ,5 t 0,5 t 44 0,5 1, ,5 t 1,0 t 44 1,5 3, ,5 t 1,0 t 44 3,0 6, ,0 t 44 6,0 12, ,5 t 44 H26 0,2 0, ,0 t 1,0 t 50 0,5 1, ,0 t 1,5 t 50 1,5 4, ,0 t 2,0 t 50 H28 0,2 0, ,5 t 58 0,5 1, ,5 t 58 1,5 3, ,0 t 58 For informtion only. 23
26 EN 485-2:2007 (E) Tble 14 Alloy EN AW-3105 [Al Mn0,5Mg0,5] over up to mx. mx. A 50 mm HBW F 2,5 80,0 100 O/H111 0,2 0, t 29 0,5 1, t 29 1,5 3, ,5 t 29 H12 0,2 0, ,5 t 41 0,5 1, ,5 t 41 1,5 3, ,5 t 41 H14 0,2 0, ,5 t 48 0,5 1, ,5 t 48 1,5 3, ,5 t 48 H16 0,2 0, ,5 1, ,5 3, H18 0,2 0, ,5 1, ,5 3, H19 0,2 0, ,5 1, H22 0,2 0, ,5 1, ,5 3, H24 0,2 0, ,5 t 47 0,5 1, ,5 t 47 1,5 3, ,5 t 47 H26 0,2 0, ,5 1, ,5 3, H28 0,2 0, ,5 1, For informtion only. 24
27 EN 485-2:2007 (E) Tble 15 Alloy EN AW-4006 [Al Si1Fe] over up to mx. mx. A 50 mm HBW F 2,5 6,0 95 O 0,2 0, t 28 0,5 1, t 28 1,5 3, t 28 3,0 6, ,0 t 28 H12 0,2 0, ,5 t 38 0,5 1, ,5 t 38 1,5 3, ,5 t 38 H14 0,2 0, ,0 t 45 0,5 1, ,0 t 45 1,5 3, ,0 t 45 T4 b 0,2 0, For informtion only. 0,5 1, ,5 3, ,0 6, b The T4 temper is not normlly supplied by the producers of wrought products such s circles, strips nd sheets. It is obtined by rpid cooling fter heting t reltively elevted temperture, bove 500 C. This therml cycle is routinely chieved when enmelling the finished products mde out of this lloy, such s frying pns, pressure cookers, pns, etc. 25
28 EN 485-2:2007 (E) Tble 16 Alloy EN AW-4007 [Al Si1,5Mn] over up to mx. mx. A 50 mm HBW b F b 2,5 6,0 110 O/H111 0,2 0, ,5 1, ,5 3, ,0 6, ,0 12, H12 0,2 0, ,5 1, ,5 3, b No dt vilble. For informtion only Tble 17 Alloy EN AW-4015 [Al Si2Mn] over up to mx. mx. A 50 mm HBW b O/H111 0,2 3, H12 0,2 0, ,5 3, H14 0,2 0, ,5 3, H16 0,2 0, ,5 3, H18 0,2 3, b No dt vilble. For informtion only. 26
29 EN 485-2:2007 (E) Tble 18 Alloy EN AW-5005 [Al Mg1(B)], lloy EN AW-5005A [Al Mg1(C)] over up to mx. mx. A 50 mm HBW F 2,5 80,0 100 O/H111 0,2 0, t 0 t 29 0,5 1, t 0 t 29 1,5 3, ,5 t 0 t 29 3,0 6, ,0 t 1,0 t 29 6,0 12, ,5 t 29 12,5 50, H12 0,2 0, ,0 t 0 t 39 0,5 1, ,0 t 0,5 t 39 1,5 3, ,5 t 1,0 t 39 3,0 6, ,0 t 39 6,0 12, ,0 t 39 H14 0,2 0, ,0 t 0,5 t 48 0,5 1, ,0 t 1,0 t 48 1,5 3, ,5 t 1,0 t 48 3,0 6, ,0 t 48 6,0 12, ,5 t 48 H16 0,2 0, ,0 t 52 0,5 1, ,5 t 52 1,5 3, ,0 t 52 3,0 4, ,5 t 52 H18 0,2 0, ,5 t 58 0,5 1, ,5 t 58 1,5 3, ,0 t 58 H19 0,2 0, ,5 1, ,5 3, H22/H32 0,2 0, ,0 t 0 t 38 0,5 1, ,0 t 0,5 t 38 1,5 3, ,5 t 1,0 t 38 3,0 6, ,0 t 38 6,0 12, ,0 t 38 27
30 EN 485-2:2007 (E) Tble 18 (continued) over up to mx. mx. A 50 mm HBW H24/H34 0,2 0, ,5 t 0,5 t 47 0,5 1, ,5 t 1,0 t 47 1,5 3, ,0 t 1,0 t 47 3,0 6, ,0 t 47 6,0 12, ,5 t 47 H26/H36 0,2 0, ,0 t 52 0,5 1, ,5 t 52 1,5 3, ,0 t 52 3,0 4, ,5 t 52 H28/H38 0,2 0, ,5 t 58 0,5 1, ,5 t 58 1,5 3, ,0 t 58 For informtion only. 28
31 EN 485-2:2007 (E) Tble 19 Alloy EN AW-5010 [AlMg 0,5Mn] over up to mx. mx. A 50 mm HBW F 2,5 80,0 90 O/H111 0,2 0, t 0 t 27 0,5 1, t 0 t 27 1,5 3, t 0 t 27 3,0 6, ,0 t 1,0 t 27 H12 0,2 0, ,5 t 0 t 36 0,5 1, ,5 t 0,5 t 36 1,5 3, ,0 t 1,0 t 36 3,0 6, ,5 t 36 H14 0,2 0, ,0 t 0,5 t 45 0,5 1, ,0 t 1,0 t 45 1,5 3, ,5 t 1,5 t 45 3,0 6, ,0 t 45 H16 0,2 0, ,5 t 1,0 t 51 0,5 1, ,5 t 1,5 t 51 1,5 4, ,5 t 2,0 t 51 H18 0,2 0, ,5 t 58 0,5 1, ,5 t 58 1,5 3, ,0 t 58 H19 0,2 0, ,5 1, ,5 3, H22 0,2 0, ,0 t 0 t 36 0,5 1, ,0 t 0,5 t 36 1,5 3, ,0 t 1,0 t 36 3,0 6, ,5 t 36 H24 0,2 0, ,5 t 0,5 t 44 0,5 1, ,5 t 1,0 t 44 1,5 3, ,0 t 1,5 t 44 H26 0,2 0, ,0 t 1,0 t 50 0,5 1, ,0 t 1,5 t 50 1,5 4, ,5 t 2,0 t 50 H28 0,2 0, ,0 t 58 0,5 1, ,5 t 58 1,5 3, ,0 t 58 For informtion only. 29
32 EN 485-2:2007 (E) O / H111 H14 H24 H34 Tble 20 Alloy EN AW-5026 [AI Mg4,5MnSiFe] over up to mx. mx. A 50 mm , , , , , , HBW No dt vilble. Tble 21 Alloy EN AW-5040 [Al Mg1,5Mn] Bend rdius over up to mx. mx. A 50 mm HBW H24/H34 0,8 1, H26/H36 1,0 2, For informtion only. 30
33 EN 485-2:2007 (E) Tble 22 Alloy EN AW-5049 [Al Mg2Mn0,8] over up to mx. mx. A 50 mm F 2,5 100,0 190 O/H111 0,2 0, ,5 t 0 t 52 0,5 1, ,5 t 0,5 t 52 1,5 3, ,0 t 1,0 t 52 3,0 6, ,0 t 1,0 t 52 6,0 12, ,0 t 52 12,5 100, H112 6,0 12, ,5 25, ,0 40, ,0 80, H12 0,2 0, ,5 1, ,5 3, ,0 6, ,0 12, ,5 40, H14 0,2 0, ,5 1, ,5 3, ,0 6, ,0 12, ,5 25, H16 0,2 0, ,5 1, ,5 3, ,0 6, H18 0,2 0, ,5 1, ,5 3, H22/H32 0,2 0, ,5 t 0,5 t 63 0,5 1, ,5 t 1,0 t 63 1,5 3, ,0 t 1,5 t 63 3,0 6, ,5 t 63 6,0 12, ,5 t 63 12,5 40, HBW 31
34 EN 485-2:2007 (E) Tble 22 (continued) over up to mx. mx. A 50 mm H24/H34 0,2 0, ,5 t 1,0 t 70 0,5 1, ,5 t 1,5 t 70 1,5 3, ,5 t 2,0 t 70 3,0 6, ,5 t 70 6,0 12, ,0 t 70 12,5 25, H26/H36 0,2 0, ,5 t 78 0,5 1, ,0 t 78 1,5 3, ,0 t 78 3,0 6, ,5 t 78 H28/H38 0,2 0, ,5 1, ,5 3, HBW For informtion only. 32
35 EN 485-2:2007 (E) Tble 23 Alloy EN AW-5050 [Al Mg1,5(C)] over up to mx. mx. A 50 mm HBW F 2,5 80,0 130 O/H111 0,2 0, t 0 t 36 0,5 1, t 0 t 36 1,5 3, ,5 t 0 t 36 3,0 6, ,0 t 36 6,0 12, ,0 t 36 12,5 50, H112 6,0 12, ,5 40, ,0 80, H12 0,2 0, t 49 0,5 1, ,5 t 49 1,5 3, ,0 t 49 H14 0,2 0, ,5 t 55 0,5 1, ,0 t 55 1,5 3, ,5 t 55 3,0 6, ,0 t 55 H16 0,2 0, ,0 t 61 0,5 1, ,5 t 61 1,5 3, ,5 t 61 3,0 4, ,0 t 61 H18 0,2 0, ,5 t 68 0,5 1, ,5 t 68 1,5 3, H22/H32 0,2 0, ,0 t 0 t 47 0,5 1, ,0 t 0,5 t 47 1,5 3, ,5 t 1,0 t 47 3,0 6, ,5 t 47 H24/H34 0,2 0, ,5 t 0,5 t 54 0,5 1, ,5 t 1,0 t 54 1,5 3, ,0 t 1,5 t 54 3,0 6, ,0 t 54 H26/H36 0,2 0, ,0 t 60 0,5 1, ,5 t 60 1,5 3, ,5 t 60 3,0 4, ,0 t 60 33
36 EN 485-2:2007 (E) Tble 23 (continued) over up to mx. mx. A 50 mm HBW H28/H38 0,2 0, ,5 t 67 0,5 1, ,5 t 67 1,5 3, For informtion only. 34
37 EN 485-2:2007 (E) Tble 24 Alloy EN AW-5052 [Al Mg2,5] over up to mx. mx. A 50 mm HBW F 2,5 80,0 165 O/H111 0,2 0, t 0 t 47 0,5 1, t 0 t 47 1,5 3, ,5 t 0,5 t 47 3,0 6, ,0 t 47 6,0 12, ,0 t 46 12,5 80, H112 6,0 12, ,5 40, ,0 80, H12 0,2 0, ,5 1, ,5 3, ,0 6, ,0 12, ,5 40, H14 0,2 0, ,5 1, ,5 3, ,0 6, ,0 12, ,5 25, H16 0,2 0, ,5 1, ,5 3, ,0 6, H18 0,2 0, ,5 1, ,5 3, H22/H32 0,2 0, ,5 t 0,5 t 61 0,5 1, ,5 t 1,0 t 61 1,5 3, ,5 t 1,5 t 61 3,0 6, ,5 t 61 6,0 12, ,5 t 61 12,5 40,
38 EN 485-2:2007 (E) Tble 24 (continued) over up to mx. mx. A 50 mm HBW H24/H34 0,2 0, ,0 t 0,5 t 67 0,5 1, ,0 t 1,5 t 67 1,5 3, ,0 t 2,0 t 67 3,0 6, ,5 t 67 6,0 12, ,0 t 67 12,5 25, H26/H36 0,2 0, ,5 t 74 0,5 1, ,0 t 74 1,5 3, ,0 t 74 3,0 6, ,5 t 74 H28/H38 0,2 0, ,5 1, ,5 3, For informtion only. O/H111/ H112 H116/ H321 c Tble 25 Alloy EN AW-5059 [Al Mg5,5MnZnZr] over up to mx. mx. A 50 mm 3,0 6, ,5 t 6,0 12, t 12,5 40, ,0 6, t 6,0 12, t 12,5 20, ,0 40, HBW b b For informtion only. No dt vilble. c Mteril supplied to tht temper shll be cpble of exhibiting no evidence of exfolition corrosion when subjected to ASTM G66 ccelerted exfolition corrosion susceptibility test. Intergrnulr corrosion susceptibility ccording to ASTM G67. 36
39 EN 485-2:2007 (E) Tble 26 Alloy EN AW-5070 [Al Mg4MnZn] b over up to mx. mx. A 50 mm O/H111 0,5 6, t 1 t For informtion only. No dt vilble. HBW b 37
40 EN 485-2:2007 (E) Tble 27 Alloy EN AW-5083 [Al Mg4,5Mn0,7] over up to mx. mx. A 50 mm HBW F 2,5 250, O/H111 0,2 0, ,0 t 0,5 t 75 0,5 1, ,0 t 1,0 t 75 1,5 3, ,5 t 1,0 t 75 3,0 6, ,5 t 75 6,3 12, ,5 t 75 12,5 50, ,0 80, ,0 120, ,0 200, ,0 250, ,0 300, H112 6,0 12, ,5 40, ,0 80, ,0 120, H116/ 1,5 3, ,0 t 2,0 t 89 H321 b 3,0 6, ,5 t 89 6,0 12, ,0 t 89 12,5 40, ,0 80, H12 0,2 0, ,5 1, ,5 3, ,0 6, ,0 12, ,5 40, H14 0,2 0, ,5 1, ,5 3, ,0 6, ,0 12, ,5 25, H16 0,2 0, ,5 1, ,5 3, ,0 4,
41 EN 485-2:2007 (E) Tble 27 (continued) over up to mx. mx. A 50 mm HBW H22/H32 0,2 0, ,0 t 0,5 t 89 0,5 1, ,0 t 1,5 t 89 1,5 3, ,0 t 2,0 t 89 3,0 6, ,5 t 89 6,0 12, ,5 t 89 12,5 40, H24/H34 0,2 0, ,0 t 99 0,5 1, ,0 t 99 1,5 3, ,5 t 99 3,0 6, ,5 t 99 6,0 12, ,5 t 99 12,5 25, H26/H36 0,2 0, ,5 1, ,5 3, ,0 4, For informtion only. b Mteril supplied to tht temper shll be cpble of exhibiting no evidence of exfolition corrosion when subjected to ASTM G66 ccelerted exfolition corrosion susceptibility test. Intergrnulr corrosion susceptibility ccording to ASTM G67. 39
42 EN 485-2:2007 (E) Tble 28 Alloy EN AW-5086 [Al Mg4] HBW over up to mx. mx. A 50 mm F 2,5 150,0 240 O/H111 0,2 0, ,0 t 0,5 t 65 0,5 1, ,0 t 1,0 t 65 1,5 3, ,0 t 1,0 t 65 3,0 6, ,5 t 1,5 t 65 6,0 12, ,5 t 65 12,5 150, H112 6,0 12, ,5 40, ,0 80, H116/H321 b 1,5 3, ,0 t 2,0 t 81 3,0 6, ,5 t 81 6,0 12, ,5 t 81 12,5 50, H12 0,2 0, ,5 1, ,5 3, ,0 6, ,0 12, ,5 40, H14 0,2 0, ,5 1, ,5 3, ,0 6, ,0 12, ,5 25, H16 0,2 0, ,5 1, ,5 3, ,0 4, H18 0,2 0, ,5 1, ,5 3, H22/H32 0,2 0, ,0 t 0,5 t 80 0,5 1, ,0 t 1,5 t 80 1,5 3, ,0 t 2,0 t 80 3,0 6, ,5 t 80 6,0 12, ,5 t 80 12,5 40,
43 EN 485-2:2007 (E) Tble 28 (continued) HBW over up to mx. mx. A 50 mm H24/H34 0,2 0, ,5 t 1,0 t 88 0,5 1, ,5 t 2,0 t 88 1,5 3, ,5 t 2,5 t 88 3,0 6, ,5 t 88 6,0 12, ,5 t 88 12,5 25, H26/H36 0,2 0, For informtion only. 0,5 1, ,5 3, ,0 4, b Mteril supplied to tht temper shll be cpble of exhibiting no evidence of exfolition corrosion when subjected to ASTM G66 ccelerted exfolition corrosion susceptibility test. Intergrnulr corrosion susceptibility ccording to ASTM G67. Tble 29 Alloy EN AW-5088 [AlMg5Mn0,4] HBW b over up to mx. mx. A 50 mm b O/H111 3,0 6, ,5 t 1 t 6,0 12, ,5 t 1 t For informtion only. No dt vilble. 41
44 EN 485-2:2007 (E) Tble 30 Alloy EN AW-5154A [Al Mg3,5(A)] over up to mx. mx. A 50 mm HBW F 2,5 80,0 215 O/H111 0,2 0, ,5 t 0,5 t 58 0,5 1, ,5 t 0,5 t 58 1,5 3, ,0 t 1,0 t 58 3,0 6, ,5 t 58 6,0 12, ,5 t 58 12,5 50, H112 6,0 12, ,5 40, ,0 80, H12 0,2 0, ,5 1, ,5 3, ,0 6, ,0 12, ,5 40, H14 0,2 0, ,5 1, ,5 3, ,0 6, ,0 12, ,5 25, H18 0,2 0, ,5 1, ,5 3, H19 0,2 0, ,5 1, H22/H32 0,2 0, ,5 t 0,5 t 74 0,5 1, ,5 t 1,0 t 74 1,5 3, ,0 t 2,0 t 74 3,0 6, ,5 t 74 6,0 12, ,0 t 74 12,5 40,
45 EN 485-2:2007 (E) Tble 30 (continued) over up to mx. mx. A 50 mm HBW H24/H34 0,2 0, ,5 t 1,0 t 80 0,5 1, ,5 t 2,0 t 80 1,5 3, ,0 t 2,5 t 80 3,0 6, ,0 t 80 6,0 12, ,0 t 80 12,5 25, H26/H36 0,2 0, ,5 1, ,5 3, ,0 6, H28/H38 0,2 0, ,5 1, ,5 3, For informtion only. 43
46 EN 485-2:2007 (E) Tble 31 Alloy EN AW-5182 [Al Mg4,5Mn0,4] over up to mx. mx. A 50 mm HBW F 2,5 80,0 255 O/H111 0,2 0, ,0 t 69 0,5 1, ,0 t 69 1,5 3, ,0 t 69 H19 0,2 0, ,5 1, For informtion only. 44
47 EN 485-2:2007 (E) Tble 32 Alloy EN AW-5251 [Al Mg2Mn0,3] over up to mx. mx. A 50 mm HBW F 2,5 80,0 160 O/H111 0,2 0, t 0 t 44 0,5 1, t 0 t 44 1,5 3, ,5 t 0,5 t 44 3,0 6, ,0 t 44 6,0 12, ,0 t 44 12,5 50, H12 0,2 0, ,0 t 0 t 58 0,5 1, ,0 t 1,0 t 58 1,5 3, ,0 t 1,0 t 58 3,0 6, ,5 t 58 6,0 12, ,5 t 58 12,5 25, H14 0,2 0, ,5 t 0,5 t 64 0,5 1, ,5 t 1,5 t 64 1,5 3, ,5 t 1,5 t 64 3,0 6, ,5 t 64 6,0 12, ,0 t 64 H16 0,2 0, ,5 t 1,0 t 71 0,5 1, ,5 t 1,5 t 71 1,5 3, ,5 t 2,0 t 71 3,0 4, ,0 t 71 H18 0,2 0, ,5 1, ,5 3, H22/H32 0,2 0, ,5 t 0 t 56 0,5 1, ,5 t 1,0 t 56 1,5 3, ,5 t 1,0 t 56 3,0 6, ,5 t 56 6,0 12, ,5 t 56 12,5 25,
48 EN 485-2:2007 (E) Tble 32 (continued) over up to mx. mx. A 50 mm HBW H24/H34 0,2 0, ,0 t 0,5 t 62 0,5 1, ,0 t 1,5 t 62 1,5 3, ,0 t 1,5 t 62 3,0 6, ,5 t 62 6,0 12, ,0 t 62 H26/H36 0,2 0, ,0 t 1,0 t 69 0,5 1, ,0 t 1,5 t 69 1,5 3, ,0 t 2,0 t 69 3,0 4, ,0 t 69 H28/H38 0,2 0, ,5 1, ,5 3, For informtion only. 46
49 EN 485-2:2007 (E) Tble 33 Alloy EN AW-5383 [Al Mg4,5Mn0,9] over up to mx. mx. A 50 mm HBW O/H111 0,2 0, ,0 t 0,5 t 85 0,5 1, ,0 t 1,0 t 85 1,5 3, ,5 t 1,0 t 85 3,0 6, ,5 t 85 6,0 12, ,5 t 85 12,5 50, ,0 80, ,0 120, ,0 150, H112 6,0 12, ,5 40, ,0 80, H116 1,5 3, ,0 t 2,0 t 90 H321 b 3,0 6, ,5 t 90 6,0 12, ,0 t 90 12,5 40, ,0 80, H22/H32 0,2 0, ,0 t 0,5 t 90 0,5 1, ,0 t 1,5 t 90 1,5 3, ,0 t 2,0 t 90 3,0 6, ,5 t 90 6,0 12, ,5 t 90 12,5 40, H24/H34 0,2 0, ,0 t 105 For informtion only. 0,5 1, ,0 t 105 1,5 3, ,5 t 105 3,0 6, ,5 t 105 6,0 12, ,5 t ,5 25, b Mteril supplied to tht temper shll be cpble of exhibiting no evidence of exfolition corrosion when subjected to ASTM G66 ccelerted exfolition corrosion susceptibility test. Intergrnulr corrosion susceptibility ccording to ASTM G67. 47
50 EN 485-2:2007 (E) Tble 34 Alloy EN AW-5449 [Al Mg2Mn0,8(B)] over up to mx. mx. A 50 mm HBW O/H111 0,5 1, ,5 3, H22 0,5 1, ,5 3, H24 0,5 1, ,5 3, H26 0,5 1, ,5 3, H28 0,5 1, ,5 3, No dt vilble. 48
51 EN 485-2:2007 (E) Tble 35 Alloy EN AW-5454 [Al Mg3Mn] over up to mx. mx. A 50 mm HBW F 2,5 120, ,0 150,0 205 O/H111 0,2 0, ,5 t 0,5 t 58 0,5 1, ,5 t 0,5 t 58 1,5 3, ,0 t 1,0 t 58 3,0 6, ,5 t 58 6,0 12, ,5 t 58 12,5 80, H112 6,0 12, ,5 40, ,0 120, H12 0,2 0, ,5 1, ,5 3, ,0 6, ,0 12, ,5 40, H14 0,2 0, ,5 1, ,5 3, ,0 6, ,0 12, ,5 25, H22/H32 0,2 0, ,5 t 0,5 t 74 0,5 1, ,5 t 1,0 t 74 1,5 3, ,0 t 2,0 t 74 3,0 6, ,5 t 74 6,0 12, ,0 t 74 12,5 40,
52 EN 485-2:2007 (E) Tble 35 (continued) over up to mx. mx. A 50 mm HBW H24/H34 0,2 0, ,5 t 1,0 t 80 0,5 1, ,5 t 2,0 t 80 1,5 3, ,0 t 2,5 t 80 3,0 6, ,0 t 80 6,0 12, ,0 t 80 12,5 25, H26/H36 0,2 0, ,5 1, ,5 3, ,0 6, H28/H38 0,2 0, ,5 1, ,5 3, For informtion only. 50
53 EN 485-2:2007 (E) Tble 36 Alloy EN AW-5754 [Al Mg3] over up to mx. mx. A 50 mm HBW F 2,5 100, ,0 150,0 180 O/H111 0,2 0, ,5 t 0 t 52 0,5 1, ,5 t 0,5 t 52 1,5 3, ,0 t 1,0 t 52 3,0 6, ,0 t 1,0 t 52 6,0 12, ,0 t 52 12,5 100, H112 6,0 12, ,5 25, ,0 40, ,0 80, H12 0,2 0, ,5 1, ,5 3, ,0 6, ,0 12, ,5 40, H14 0,2 0, ,5 1, ,5 3, ,0 6, ,0 12, ,5 25, H16 0,2 0, ,5 1, ,5 3, ,0 6, H18 0,2 0, ,5 1, ,5 3, H22/H32 0,2 0, ,5 t 0,5 t 63 0,5 1, ,5 t 1,0 t 63 1,5 3, ,0 t 1,5 t 63 3,0 6, ,5 t 63 6,0 12, ,5 t 63 12,5 40,
54 EN 485-2:2007 (E) Tble 36 (continued) over up to mx. mx. A 50 mm HBW H24/H34 0,2 0, ,5 t 1,0 t 70 0,5 1, ,5 t 1,5 t 70 1,5 3, ,5 t 2,0 t 70 3,0 6, ,5 t 70 6,0 12, ,0 t 70 12,5 25, H26/H36 0,2 0, ,5 t 78 0,5 1, ,0 t 78 1,5 3, ,0 t 78 3,0 6, ,5 t 78 H28/H38 0,2 0, ,5 1, ,5 3, For informtion only. 52
Aluminium and aluminium alloys Sheet, strip and plate
BSI Stndrds Publiction Aluminium nd luminium lloys Sheet, strip nd plte Prt : Mechnicl properties BRITISH STANDARD Ntionl foreword This British Stndrd is the UK implementtion of EN 8-:. It supersedes BS
More informationEurocode 3 Design of steel structures
BRITISH STANDARD BS EN 1993-3-2:2006 Eurocode 3 Design of steel structures Part 3-2: Towers, masts and chimneys Chimneys ICS 91.010.30; 91.060.40; 91.080.10 National foreword This British Standard is the
More informationEurocode 2 Design of concrete structures
BRITISH STANDARD BS EN 1992-3:2006 Eurocode 2 Design of concrete structures Part 3: Liquid retaining and containment structures The European Standard EN 1992-3:2006 has the status of a British Standard
More informationEurocode 3 Design of steel structures
BRITISH STANDARD BS EN 1993-1-5:2006 Incorporating corrigendum April 2009 Eurocode 3 Design of steel structures Part 1-5: Plated structural elements ICS 91.010.30; 91.080.10 National foreword This British
More informationEurocode 3 Design of steel structures
BRITISH STANDARD BS EN 1993-5:2007 Incorporating corrigendum May 2009 Eurocode 3 Design of steel structures Part 5: Piling ICS 91.010.30; 91.080.10 National foreword This British Standard is the UK implementation
More informationEurocode 1 Actions on structures
BRITISH STANDARD Eurocode 1 Actions on structures BS EN 1991-1-3:2003 Incorporating corrigenda December 2004 and March 2009 Part 1-3: General actions Snow loads ICS 91.010.30 National foreword This British
More informationEurocode 3 Design of steel structures
BRITISH STANDARD BS EN 1993-2:2006 Incorporating corrigendum July 2009 Eurocode 3 Design of steel structures Part 2: Steel bridges ICS 91.010.30; 91.080.10; 93.040 National foreword This British Standard
More informationEurocode 3 Design of steel structures
BRITISH STANDARD BS EN 1993-3-1:2006 Incorporating corrigendum July 2009 Eurocode 3 Design of steel structures Part 3-1: Towers, masts and chimneys Towers and masts ICS 91.010.30; 91.080.10 National foreword
More informationEurocode 8: Design of structures for earthquake resistance
BRITISH STANDARD BS EN 1998-4:2006 Eurocode 8: Design of structures for earthquake resistance Part 4: Silos, tanks and pipelines The European Standard EN 1998-4:2006 has the status of a British Standard
More informationEurocode 3 Design of steel structures
BRITISH STANDARD BS EN 1993-1-6:2007 Incorporating corrigendum April 2009 Eurocode 3 Design of steel structures Part 1-6: Strength and Stability of Shell Structures ICS 91.010.30; 91.080.10 National foreword
More informationPart 3: Specifications for pipes and fittings with smooth internal and profiled external surface and the system, Type B BS EN :2007 +A1:2009
BRITISH STANDARD BS EN 13476-3:2007 +A1:2009 Plstics piping systems for non-pressure underground dringe nd sewerge Structured-wll piping systems of unplsticized poly(vinyl chloride) (PVC-U), polypropylene
More informationDEUTSCHE NORM June Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristics (ISO : 2001)
DEUTSCHE NORM June 2002 Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristics (ISO 1043-1 : 2001) English version of DIN EN ISO 1043-1 { EN ISO 1043-1 ICS 01.040.83;
More informationContinuously hot-rolled strip and plate/sheet cut from wide strip of nonalloy and alloy steels - Tolerances on dimensions and shape
Irish Standard Continuously hot-rolled strip and plate/sheet cut from wide strip of nonalloy and alloy steels - Tolerances on dimensions and shape NSAI 2010 No copying without NSAI permission except as
More informationRESILIENT AND LAMINATE FLOOR COVERINGS - CASTOR CHAIR TEST IRISH STANDARD I.S. EN 425:2002. Price Code. Údarás um Chaighdeáin Náisiúnta na héireann
IRISH STANDARD I.S. EN 425:2002 ICS 97.150 National Standards Authority of Ireland Dublin 9 Ireland Tel: (01) 807 3800 Tel: (01) 807 3838 RESILIENT AND LAMINATE FLOOR COVERINGS - CASTOR CHAIR TEST NSAI
More informationDEUTSCHE NORM February 2005 DIN EN ISO 1514 { Paints and varnishes Standard panels for testing (ISO 1514 : 2004) English version of DIN EN ISO 1514
DEUTSCHE NORM February 2005 DIN EN ISO 1514 { ICS 87.100 Supersedes September 1997 edition. Paints and varnishes Standard panels for testing (ISO 1514 : 2004) English version of DIN EN ISO 1514 Beschichtungsstoffe
More informationINDUSTRIAL VALVES - ISOLATING VALVES FOR LNG - SPECIFICATION FOR SUITABILITY AND APPROPRIATE VERIFICATION TESTS IRISH STANDARD I.S.
IRISH STANDARD I.S. EN 12567:2000 ICS 23.060.01 National Standards Authority of Ireland Dublin 9 Ireland INDUSTRIAL VALVES - ISOLATING VALVES Tel: (01) 807 3800 Tel: (01) 807 3838 FOR LNG - SPECIFICATION
More informationWaste fittings for sanitary appliances
BRITISH STANDARD BS EN 274-2:2002 Incorporating Corrigendum No. 1 Waste fittings for sanitary appliances Part 2: Test methods The European Standard EN 274-2:2002 has the status of a British Standard ICS
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-32581-7 SOUTH AFRICAN NATIONAL STANDARD Gravity drainage systems inside buildings Part 3: Roof drainage, layout and calculation This national standard is the identical implementation of,
More informationSteel wire ropes - Terminations for steel wire ropes Safety - Metal and resin socketing
Draft SI part 34 34 October 2011 2011 ICS CODE ###### Steel wire ropes Terminations for steel wire ropes Safety Metal and resin socketing The Standards Institution of Israel 24/10/11 #### wwwsiiorgil 036412762
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-26065-1 Edition 1 EN 12281:2002 Edition 2 SOUTH AFRICAN NATIONAL STANDARD Printing and business paper Requirements for copy paper for dry toner imaging processes This national standard is
More information1. Energy. Reference approach Sectoral approach Difference Explanation for difference as reported in table 1.A(c) of the CRF
1. Energy Energy - Totl CO 2 emissions from the reference pproch nd the sectorl pproch (2000) CO 2 emissions from totl fuel combustion Reference pproch Sectorl pproch Difference Explntion for difference
More informationDEUTSCHE NORM January Fasteners Electroplated coatings (ISO 4042 : 1999) English version of DIN EN ISO 4042
DEUTSCHE NORM January 2001 Fasteners Electroplated coatings (ISO 4042 : 1999) English version of DIN EN ISO 4042 { EN ISO 4042 ICS 21.060.01; 25.220.40 Verbindungselemente Galvanische Überzüge (ISO 4042
More informationDEUTSCHE NORM October Structural steel equal and unequal leg angles Part 1: Dimensions English version of DIN EN
DEUTSCHE NORM October 1998 Structural steel equal and unequal leg angles Part 1: Dimensions English version of DIN EN 10056-1 { EN 10056-1 ICS 77.140.70 Descriptors: Structural steel, angles, dimensions.
More informationDEUTSCHE NORM May 2004 DIN EN ISO 4029 { Hexagon socket set screws with cup point (ISO 4029 : 2003) English version of DIN EN ISO 4029
DEUTSCHE NORM May 2004 DIN EN ISO 4029 { ICS 21.060.10 Supersedes DIN 916, December 1980 edition. Hexagon socket set screws with cup point (ISO 4029 : 2003) English version of DIN EN ISO 4029 Gewindestifte
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-29507-3 EN 413-1:2011 SOUTH AFRICAN NATIONAL STANDARD Masonry cement Part 1: Composition, specifications and conformity criteria This national standard is the identical implementation of
More informationDEUTSCHE NORM October Steels Determination of depth of decarburization (ISO 3887 : 2003) English version of DIN EN ISO 3887
DEUTSCHE NORM October 2003 Steels Determination of depth of decarburization (ISO 3887 : 2003) English version of DIN EN ISO 3887 { EN ISO 3887 ICS 77.040.99 Stahl Bestimmung der Entkohlungstiefe (ISO 3887
More informationDEUTSCHE NORM March Hexagon head bolts Product grade C (ISO 4016 : 1999) English version of DIN EN ISO 4016
DEUTSCHE NORM March 2001 Hexagon head bolts Product grade C (ISO 4016 : 1999) English version of DIN EN ISO 4016 { EN ISO 4016 ICS 21.060.10 Sechskantschrauben mit Schaft Produktklasse C (ISO 4016 : 1999)
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 12092:2002 Adhesives - Determination of viscosity Adhesives - Determination of viscosity EESTI STANDARDIKESKUS EESTI STANDARDI EESSÕNA NATIONAL FOREWORD Käesolev Eesti standard EVS-EN
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-30207-8 SOUTH AFRICAN NATIONAL STANDARD Chemicals used for treatment of water intended for human consumption Chlorine This national standard is the identical implementation of and is adopted
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 12592:2007 Bitumen and bituminous binders - Determination of solubility Bitumen and bituminous binders - Determination of solubility EESTI STANDARDIKESKUS EESTI STANDARDI EESSÕNA
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 12606-1:2007 Bitumen and bituminous binders - Determination of the paraffin wax content - Part 1: Method by distillation Bitumen and bituminous binders - Determination of the paraffin
More informationCOLD ROLLED STEEL SECTIONS -
STANDARD I.S. EN 10162:2003 ICS 77.140.70 National Standards Authority of Ireland Dublin 9 Ireland COLD ROLLED STEEL SECTIONS - Tel: (01) 807 3800 Fax: (01) 807 3838 TECHNICAL DELIVERY CONDITIONS - DIMENSIONAL
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-28107-6 EN 1008:2002 SOUTH AFRICAN NATIONAL STANDARD Mixing water for concrete Specification for sampling, testing and assessing the suitability of water, including water recovered from
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 12642:2006 Securing of cargo on road vehicles - Body structure of commercial vehicles - Minimum requirements Securing of cargo on road vehicles - Body structure of commercial vehicles
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 14432:2006 Tanks for the transport of dangerous goods - Tank equipment for the transport of liquid chemicals - Product discharge and air inlet valves Tanks for the transport of dangerous
More informationProvläsningsexemplar / Preview
Provläsningsexemplar / Preview EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN 14975:2006+A1 July 2010 ICS 91.060.30 Supersedes EN 14975:2006 English Version Loft ladders - Requirements, marking
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 13594:2002 Kaitsekindad professionaalsete mootorratturitele. Nõuded ja katsemeetodid Protective gloves for professional motorcycle riders - Requirements and test methods EESTI STANDARDIKESKUS
More informationDEUTSCHE NORM February 2003
DEUTSCHE NORM February 2003 Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylenediene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)- styrene (ACS) moulding and extrusion
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 14895:2006 Bitumen and bituminous binders - Stabilisation of binder from bituminous emulsions or from cut-back and fluxed bituminous binders Bitumen and bituminous binders - Stabilisation
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 13652:2002 Soil improvers and growing media - Extraction of water soluble nutrients and elements Soil improvers and growing media - Extraction of water soluble nutrients and elements
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-28152-6 EN 197-1:2011 SOUTH AFRICAN NATIONAL STANDARD Cement Part 1: Composition, specifications and conformity criteria for common cements This national standard is the identical implementation
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 840-1:2004 Teisaldatavad heitmekonteinerid. Osa 1: Kaherattalised konteinerid mahuga kuni 400 l, tõstmiseks kammtõsteseadistega, mõõtmed ja konstrueerimine Mobile waste containers
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 12900:2005 Refrigerant compressors - Rating conditions, tolerances and presentation of manufacturer's performance data Refrigerant compressors - Rating conditions, tolerances and
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 10219-2:2006 Külmsurvevormitud keevitatud konstruktsiooni-õõnesprofiilid mittelegeerja peeneteraterastest. Osa 2: Tolerantsid, mõõtmed ja profiili omadused Cold formed welded structural
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 12806:2003 Automotive liquefied petroleum gas components - Other than containers Automotive liquefied petroleum gas components - Other than containers EESTI STANDARDIKESKUS EESTI
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 15020:2006 Raudteealased rakendused. Pukseerseadmed. Toimimisnõuded, liidese erigeomeetria ja katsemeetodid Railway applications - Rescue coupler - Performance requirements, specific
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 14067-3:2003 Railway applications - Aerodynamics - Part 3: Aerodynamics in tunnels Railway applications - Aerodynamics - Part 3: Aerodynamics in tunnels EESTI STANDARDIKESKUS EESTI
More informationSOUTH AFRICAN NATIONAL STANDARD
Copying nd network storge prohibited. ISBN 978-0-626-31934-2 SANS 62841-3-6:2016 Edition 1 nd IEC corr. 1 :2014 Edition 1 nd corr. 1 SOUTH AFRICAN NATIONAL STANDARD Electric motor-operted hnd-held tools,
More informationEurocode 1: Actions on structures
BRITISH STANDARD Eurocode 1: Actions on structures BS EN 1991-1-4:2005 +A1:2010 Incorporating corrigenda July 2009 and January 2010 Part 1-4: General actions Wind actions ICS 91.010.30 National foreword
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 12255-6:2002 Wastewater treatment plants - Part 6: Activated sludge processes Wastewater treatment plants - Part 6: Activated sludge processes EESTI STANDARDIKESKUS EESTI STANDARDI
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-31521-4 EN 300:2006 SOUTH AFRICAN NATIONAL STANDARD Oriented Strand Boards (OSB) Definitions, classification and specifications This national standard is the identical implementation of
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 12122:2005 Chemicals used for treatment of water intended for human consumption - Ammonium solution Chemicals used for treatment of water intended for human consumption - Ammonia
More informationEVS-EN 13953:2003+A1:2007 This document is a preview generated by EVS
EESTI STANDARD EVS-EN 13953:2003+A1:2007 LPG equipment and accessories - Pressure relief valves for transportable refillable cylinders for Liquefied Petroleum Gas (LPG) (KONSOLIDEERITUD TEKST) LPG equipment
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 284:2006 Transpordipakendid. Klassi C transpordipakendid. Mõõtmed ja üldnõuded Swap bodies - Non-stackable swap bodies of class C - Dimensions and general requirements EESTI STANDARDIKESKUS
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 13452-1:2003 Railway applications - Braking - Mass transit brake systems - Part 1: Performance requirements Railway applications - Braking - Mass transit brake systems - Part 1: Performance
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 14832:2005 Petroleum and related products - Determination of the oxidation stability and corrosivity of fire-resistant phosphate ester fluids Petroleum and related products - Determination
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 1983:2006 Tööstuslikud ventiilid. Terasest kuulklapid Industrial valves - Steel ball valves EESTI STANDARDIKESKUS EESTI STANDARDI EESSÕNA NATIONAL FOREWORD Käesolev Eesti standard
More informationShell boilers. Part 8: Requirements for safeguards against excessive pressure. BS EN :2001 Incorporating Corrigendum No. 1 BRITISH STANDARD
BRITISH STANDARD Shell boilers Part 8: Requirements for safeguards against excessive pressure The European Standard EN 12953-8:2001 has the status of a British Standard ICS 27.060.30; 27.100 BS EN 12953-8:2001
More informationWATER-TUBE BOILERS AND AUXILIARY
IRISH STANDARD I.S. EN 12952-12:2003 ICS 13.060.25 27.040 WATER-TUBE BOILERS AND AUXILIARY National Standards Authority of Ireland Dublin 9 Ireland Tel: (01) 807 3800 Tel: (01) 807 3838 INSTALLATIONS -
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 12674-3:2004 Roll containers - Part 3: Test methods Roll containers - Part 3: Test methods EESTI STANDARDIKESKUS EESTI STANDARDI EESSÕNA NATIONAL FOREWORD Käesolev Eesti standard
More informationDEUTSCHE NORM July 2004 DIN EN ISO 9038 { Test for sustained combustibility of liquids (ISO 9038 : 2002) English version of DIN EN ISO 9038
DEUTSCHE NORM July 2004 DIN EN ISO 9038 { ICS 13.220.40; 87.040 Test for sustained combustibility of liquids (ISO 9038 : 2002) English version of DIN EN ISO 9038 Prüfung der Weiterbrennbarkeit von Flüssigkeiten
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 12284:2003 Külmetussüsteemid ja soojuspumbad. Ventiilid. Nõuded, testimine ja markeerimine Refrigerating systems and heat pumps - Valves - Requirements, testing and marking EESTI
More informationGas turbines Procurement
BRITISH STANDARD Gas turbines Procurement BS EN ISO 3977-5:2003 Incorporating Amendment No. 1 (renumbers BS ISO 3977-5:2001 as BS EN ISO 3977-5:2003) Part 5: Applications for petroleum and natural gas
More information631 ALLOWANES AND TOLERANCES
631 ALLOWANES AND TOLERANCES ANSI Fits. Tbles 3 through 9 inclusive show series of stndrd types nd clsses of fits on unilterl hole bsis, such tht the fit produced by mting prts in ny one clss will produce
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 14620-3:2006 Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between
More informationDEUTSCHE NORM DIN EN 10080
DEUTSCHE NORM DIN EN 10080 August 2005 { ICS 77.140.15; 77.140.60; 77.140.65 Supersedes DIN V ENV 10080, August 1995 edition, parts of DIN 488-1, September 1984 edition, DIN 488-2, DIN 488-4 and DIN 488-6,
More informationBUILDING LIME - PART 2: TEST METHODS IRISH STANDARD I.S. EN 459-2:2002. Price Code. Údarás um Chaighdeáin Náisiúnta na héireann
IRISH STANDARD I.S. EN 459-2:2002 ICS 91.100.10 National Standards Authority of Ireland Dublin 9 Ireland Tel: (01) 807 3800 Tel: (01) 807 3838 BUILDING LIME - PART 2: TEST METHODS NSAI 2002 Údarás um Chaighdeáin
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 14367:2005 Backflow preventer with different non controllable pressure zones - Family C - Type A Non controllable backflow preventer with different pressure zones - Family C, type
More informationStructural steel equal and unequal leg
BRITISH STANDARD BS EN 10056-1:1999 The European Standard has the status of a British Standard ICS 77.140.70 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Structural steel equal
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 12173:2005 Chemicals used for treatment of water intended for human consumption - Sodium fluoride Chemicals used for treatment of water intended for human consumption - Sodium fluoride
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 15199-2:2006 Petroleum products - Determination of boiling range distribution by gas chromatography method - Part 2: Heavy distillates and residual fuel Petroleum products - Determination
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 13149-1:2004 Public transport - Road vehicle scheduling and control systems - Part 1: WORLDFIP definition and application rules for onboard data transmission Public transport - Road
More informationThis document is a preview generated by EVS
EUROPEAN PRESTANDARD PRÉNORME EUROPÉENNE EUROPÄISCHE VORNORM ENV 807 May 2001 ICS 71.100.50 Supersedes ENV 807:1993 English version Wood preservatives - Determination of the effectiveness against soft
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 13654-1:2002 Soil improvers and growing media - Determination of nitrogen - Part 1: Modified Kjeldahl method Soil improvers and growing media - Determination of nitrogen - Part 1:
More informationSOUTH AFRICAN NATIONAL STANDARD
ICS 83.080.20; 83.140.30 ISBN 0-626-14156-7 SANS 12107:2003 SOUTH AFRICAN NATIONAL STANDARD Plastics piping systems Injection-moulded thermoplastics fittings, valves and ancillary equipment Determination
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 13628-1:2002 Packaging - Flexible packaging material - Determination of residual solvents by static headspace gas chromatography - Part 1: Absolute methods Packaging - Flexible packaging
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 15490:2007 Ethanol as a blending component for petrol - Determination of phe Ethanol as a blending component for petrol - Determination of phe EESTI STANDARDIKESKUS EESTI STANDARDI
More informationSkodon Provningsmetoder för ovanläder Egenskaper vid hög temperatur. Footwear Test methods for uppers High temperature behaviour
SVENSK STANDARD SS-EN 13519 Fastställd 2002-05-03 Utgåva 1 Skodon Provningsmetoder för ovanläder Egenskaper vid hög temperatur Footwear Test methods for uppers High temperature behaviour ICS 61.060 Språk:
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 12120:2005 Chemicals used for treatment of water intended for human consumption - Sodium hydrogen sulfite Chemicals used for treatment of water intended for human consumption - Sodium
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 13535:2001 Fertilizers and liming materials - Classification Fertilizers and liming materials - Classification EESTI STANDARDIKESKUS EESTI STANDARDI EESSÕNA NATIONAL FOREWORD Käesolev
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 1092-4:2002 Äärikud ja nende ühendused. Ringäärikud torudele, ventiilidele, ühendusdetailidele ja abiseadmetele, PN määratud. Osa 4: Alumiiniumsulamist äärikud Flanges and their joints
More informationKondenserade petroleumgaser Metod för provtagning (ISO 4257:2001) Liquefied petroleum gases Method of sampling (ISO 4257:2001)
SVENSK STANDARD SS-EN ISO 4257 Fastställd 2001-09-14 Utgåva 2 Kondenserade petroleumgaser Metod för provtagning (ISO 4257:2001) Liquefied petroleum gases Method of sampling (ISO 4257:2001) ICS 75.160.30
More informationDel 8: Krav på skyddsanordningar mot skadligt tryck. Shell boilers Part 8: Requirements for safeguards against excessive pressure
SVENSK STANDARD SS-EN 12953-8 Fastställd 2001-12-07 Utgåva 1 Eldrörspannor Del 8: Krav på skyddsanordningar mot skadligt tryck Shell boilers Part 8: Requirements for safeguards against excessive pressure
More informationAerospace series O-rings, in fluorosilicone rubber (FVMQ) Technical specification
SVENSK STANDARD SS-EN 3747 Fastställd 2003-01-31 Utgåva 1 Aerospace series O-rings, in fluorosilicone rubber (FVMQ) Technical specification ICS 49.025.40 Språk: engelska Publicerad: mars 2003 Copyright
More informationDEUTSCHE NORM June 2006 DIN EN { ICS Supersedes DIN EN : See start of validity
DEUTSCHE NORM June 2006 DIN EN 14399-6 { ICS 21.060.30 Supersedes DIN EN 14399-6:2005-06 See start of validity High-strength structural bolting assemblies for preloading Part 6: Plain chamfered washers
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 15519:2007 Paper and board intended to come into contact with foodstuffs - Preparation of an organic solvent extract Paper and board intended to come into contact with foodstuffs
More informationSVENSK STANDARD SS-EN 12770
SVENSK STANDARD SS-EN 12770 Handläggande organ Fastställd Utgåva Sida Standardiseringsgruppen STG 2000-02-18 1 1 (1+11) Copyright SIS. Reproduction in any form without permission is prohibited. Footwear
More informationSteel forgings for pressure purposes Part 5: Martensitic, austenitic and austenitic-ferritic stainless steels English version of DIN EN
DEUTSCHE NORM February 2000 Steel forgings for pressure purposes Part 5: Martensitic, austenitic and austenitic-ferritic stainless steels English version of DIN EN 10222-5 { EN 10222-5 ICS 23.020,30; 77.140.80;
More informationDEUTSCHE NORM January 2004 DIN EN {
DEUTSCHE NORM January 2004 DIN EN 13698-1 { ICS 55.180.20 Supersedes DIN 15146-2, November 1986 edition. Pallet production specification Part 1: Construction specification for 800 mm 1200 mm flat wooden
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 14066:2003 Natural stone test methods - Determination of resistance to ageing by thermal shock Natural stone test methods - Determination of resistance to ageing by thermal shock
More informationhttp://www.sis.se http://www.sis.se http://www.sis.se http://www.sis.se http://www.sis.se Provläsningsexemplar / Preview SVENSK STANDARD SS-EN 14420-6:2004+A1:2007 Fastställd 2007-02-09 Utgåva 1 Klämkoppling
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 15520:2007 Thermal spraying - Recommendations for constructional design of components with thermally sprayed coatings Thermal spraying - Recommendations for constructional design
More informationGasflaskor Fyllningsförhållanden för batterifordon för acetylen
SVENSK STANDARD SS-EN 13720 Fastställd 2003-03-28 Utgåva 1 Gasflaskor Fyllningsförhållanden för batterifordon för acetylen Transportable gas cylinders Filling conditions for acetylene battery vehicles
More informationDEUTSCHE NORM June 2002
DEUTSCHE NORM June 2002 Flanges and their joints Circular flanges for pipes, valves, fittings and accessories Part 1: Steel flanges, PN designated English version of DIN EN 1092-1 { EN 1092-1 ICS 23.040.60
More informationMETALLIC MATERIALS - CONVERSION OF HARDNESS VALUES (ISO 18265:2003) IRISH STANDARD I.S. EN ISO 18265:2003. Price Code
IRISH STANDARD I.S. EN ISO 18265:2003 ICS 77.040.01 National Standards Authority of Ireland Dublin 9 Ireland Tel: (01) 807 3800 Tel: (01) 807 3838 METALLIC MATERIALS - CONVERSION OF HARDNESS VALUES (ISO
More informationLaboratorieglas Byretter (ISO 385:2005)
SVENSK STANDARD SS-EN ISO 385:2005 Fastställd 2005-07-11 Utgåva 1 Laboratorieglas Byretter (ISO 385:2005) Laboratory glassware Burettes (ISO 385:2005) ICS 17.060; 71.040.20 Språk: engelska Publicerad:
More informationThis document is a preview generated by EVS
EESTI STANDARD EVS-EN 15469:2007 Petroleum products - Test method for free water in liquefied petroleum gas by visual inspection Petroleum products - Test method for free water in liquefied petroleum gas
More informationSVENSK STANDARD SS-EN :2006. Offshore containers and associated lifting sets Part 2: Lifting sets Design, manufacture and marking
SVENSK STANDARD SS-EN 12079-2:2006 Fastställd 2006-04-28 Utgåva 1 Offshore containers and associated lifting sets Part 2: Lifting sets Design, manufacture and marking ICS 55.180.10 Språk: engelska Publicerad:
More informationGasflaskor - Koniska gängor av typ 25E för anslutning av ventiler till gasflaskor - Del 2: Gängtolk
Transportable gas cylinders - 25E taper thread for connection of valves to gas cylinders - Part 2: Gauge inspection Gasflaskor - Koniska gängor av typ 25E för anslutning av ventiler till gasflaskor - Del
More informationAnnex II Emission reduction commitments
Annex II Emission redution ommitments 1. The emission redution ommitments listed in the tles elow relte to the provisions of rtile 3, prgrphs 1 nd 10, of the present Protool. 2. Tle 1 inludes the emission
More information