Thermoplastic Hoses for Hydraulics & Industry

Transcription

1 Thermoplastic Hoses for Hydraulics & Industry Catalogue 4460-UK

2 Hüttenfeld / Germany Wissembourg / France Almelo / Netherlands Ravenna / Ohio Stafford / Texas Hose assemblies are used to transmit various kinds of fluids at considerable pressures. The critical zone of a hose assembly is the connection between flexible hose and rigid fitting (crimping area). Only the use of original polyflex components (hose, fittings and tooling) and full compliance with the polyflex assembly instructions can guarantee safety and conformity with standards. When making and testing hose assemblies in connection with the respective field of application the guidelines and technical regulations as well as protection and hazard prevention rulings must be adhered to. You as the manufacturer of polyflex hose assemblies are obliged to mark the hose assemblies according to the regulations. Non-compliance with these rules can lead to the failure of a hose assembly and the loss of warranty.

3 Thermoplastic hose, fittings and accessories for hydraulic and industrial applications I

4 Thermoplastic hose, fittings and accessories for hydraulic and industrial applications Parker Hannifin offers an extensive programme of systems and components for fluid technology. Parker is structured by sales offices and manufacturing divisions to guarantee optimum focus on our customers' demands and market interests at any time. The Polyflex division, with headquarters located in Hüttenfeld, Germany, provides thermoplastic hoses and tubes. These are applied in a variety of different markets such as standard hydraulics, ultra high pressure applications, and oil & gas industry. As a market leader in many areas and with a unique product range we are pleased to assist you with all your queries. This catalogue includes hoses and fittings for a pressure range up to 70 MPa. The indicated fittings are always adapted to the correspondent hose and offer optimum performance. II

5 Thermoplastic hose, fittings and accessories for hydraulic and industrial applications III

6 Thermoplastic hose, fittings and accessories for hydraulic and industrial applications Listed below are the many reasons why you should consider Parker thermoplastic hoses for your next hydraulic or pneumatic application. This summary gives an overview of the features, advantages, and benefits of our fine and extensive line of thermoplastic hoses. Each hose is described in detail within this catalogue. We suggest reviewing this section before you proceed with your selection. Very small sizes starting with inner diameters of 2 mm (DN2 or -012). Typical disadvantages such as extensive costs, waste of space, extensive weight, and complicated installation, which are caused by using oversized hoses, can be avoided. Lightweight by design more than 50% weight reduction compared to conventional hydraulic hoses possible. Very small outer diameters due to compact design. Small bend radii to save installation space. Preformed hose assemblies acc. to customer's requirements. Combine the advantages of formed steel pipes and flexible hose assemblies Long continuous hose lengths up to 4000 m help minimise scrap due to unusable cut-off pieces and often render connection joints unnecessary. Wide range of colours for easy identification of hose function and to harmonise the appearance of machine and hose. Easy cutting and processing, especially with textile fibre reinforced hose types. IV

7 Thermoplastic hose, fittings and accessories for hydraulic and industrial applications Very high working pressures up to 400 MPa (see special catalogue 4462 "Thermoplastic Hoses for Ultra High Pressure"). Reduced pressure loss due to smooth core tubes. Electrically non-conductive hoses according to SAE J517. Volumetric expansion according to customers needs. High purity of the extremely smooth core tube reduces the danger of contamination of the hydraulic system caused by deposits in the hose. Excellent abrasion resistance. High collapse pressure. Long shelf life. Individual customer hose bundles. Customer specific hose marking. Outstanding chemical resistance of hose outer cover against environmental effects of hose core tube against fluids Long life time due to excellent UV and ozone resistance. Sea water resistant hose materials. Wide temperature range from -73 C up to 232 C. Easy bonding of hoses together into twinline or multiline assemblies to achieve space saving and compact units. Suitable for industrial gases. V

8 Thermoplastic hose, fittings and accessories for hydraulic and industrial applications Standard hydraulics Mini hydraulics Industrial hydraulics Mobile hydraulics Chemical industry Process engineering Industrial gases Alternative fuels Automotive and truck industry Boats and yachts Pneumatics Push-Lok self-grip hoses PTFE hoses and tubes Paint spray hoses Gas hoses Hoses for alternative fuels Hydraulic hoses Fittings Crimping presses and accessories VI

9 Thermoplastic hose, fittings and accessories for hydraulic and industrial applications VII

10 Thermoplastic hose, fittings and accessories for hydraulic and industrial applications VIII

11 Thermoplastic hose, fittings and accessories for hydraulic and industrial applications Since 1st July 2007 the EU End-of-life Vehicle Directive (ELV) came into force. European Community Directive 2000/53/EG of 27th July 2002 includes: specified exceptions and the prohibition of cadmium Chromium-6 has been classified in the EU Directive 67/548/ EWG as Category 2, which means that this material can under certain circumstances act as a carcinogenic. Skin contact can bring about allergic reactions. Since 2006, all Parker steel fittings have been manufactured using trivalent chromate (Chromium-6-Free) plating. This new process enhances the corrosion resistance of the fittings, and is more environmentally friendly than the previous hexavalent chromate plating. While the fitting function will not change, the colour is now silver instead of gold. The new plating process is implemented worldwide at all Parker facilities. IX

12 Thermoplastic hose, fittings and accessories for hydraulic and industrial applications Parker has developed a global system which offers a secure and functional crimping process without extensive training or complex machinery. The crimper provides a stop position. Thus there is no need for the user to make complicated adjustments just use the correct combination of hose, fitting and die set. The Parkrimp crimping tools have been designed especially for Parflex hoses. The die set segments are joined together and each die set is marked with identification grooves for quick assignment to the fitting series. Additionally they are colour coded with respect to the fitting size. Parkrimp crimping tools are suitable for Parkrimp, KarryKrimp and MiniKrimp crimping presses. Of course Parker thermoplastic hoses can be assembled also with free adjustable crimpers. Please refer to pages H-1 ff. for the related crimp diameters and assembly procedures. X

13 Thermoplastic hose, fittings and accessories for hydraulic and industrial applications Hose type Core tube material Hose inner diameter (Dash size) Option Fitting 1 = Crimp-on fitting 2 = Reusable fitting 3 = Push-Lok fitting Connection code Parker fitting series Connection size thread/ tube Hose inner diameter (Dash size) Material Without extension = galvanised steel C = stainless steel B = brass XI

14 Thermoplastic hose, fittings and accessories for hydraulic and industrial applications Part number Volumetric expansion Hose ID Weight Hose OD Thread size Working Pressure Hex size Burst pressure Diameter Minimum bend radius Hg Vacuum XII

15 Hose and fitting selection Hose selection by application... A-4 Hose selection by working pressure and ID... A-6 Hose selection by fluid compatibility/chemical resistance... A-8 Hose selection by standards and approvals... A-14 Determination of hose size... A-15 Pressure drop... A-16 Fittings overview... A-18 Fittings cross reference table... A-24 The content contained in this catalogue has been compiled with the greatest care and corresponds to the information currently available to us. However, we would like to point out that we reserve the right to make technical changes and we kindly request you to contact us should you have any special questions. A-1

16 Hose and fitting selection Several criteria must be considered, when selecting the optimal hose for your application. According to the particular application there is as a rule at least one of these characteristics crucial for the selection. In this section you will find the most important criteria and relevant selection guidelines. A-2

17 Hose and fitting selection This overview designates some application ranges together with hoses, which have proved to be especially suited for the associated application. Please note that only the most important applications can be listed. Moreover, the suitability of the desired hose for the individual environmental conditions must be verified. When working pressure and ID are given, use this table to select the possible hoses for the desired pressure range. Many applications require highly chemical resistant materials due to aggressive media. The table lists chemical fluids and rating codes for different hose materials. This overview lists hose types by international standards, approvals and certificates. If you are not sure about the hose ID suitable for your application, the flow capacity nomogram and the pressure drop chart will assist you in selecting the correct hose size. A-3

18 Hose and fitting selection A-4

19 Hose and fitting selection A-5

20 Hose and fitting selection A-6

21 Hose and fitting selection A-7

22 Hose and fitting selection G : Good to excellent. Little or no swelling, tensile or surface changes. Preferred choice. L : Marginal or conditional. Noticeable effects but not necessarily indicating lack of safety. Further testing suggested for specific application. P : Poor or unsatisfactory. Not recommended without extensive and realistic testing. : Indicates that this was not tested. * : Biopetroleum must be tested individually due to its varying composition. polyflex H Polyester elastomer 2040H, 2370H, 515H, 518C, 550H, 55LT, 560, 590, 1202LT N Polyamide 2020N, 2040N, 2244N, 2245N, 2370N, 520N, 528N, 540N, 575X, 580N, 588N, PTA, 8LPG NC Nylon copolymer 510A, 5CNG TFE Polytetrafluoroethylene (PTFE) 2030T (V70, R14, CON), 2033T, 929/929B, 939/939B, 919U U Polyurethane 2010N, 2040N (V00), 2040H, 2244N, 2245N, 2370H, 2370N, 510, 830, 838, 515H, 510A, 540N, 550H, 560, 520N, 528N, 580N, 588N, 590, 919U, 5CNG HF Special elastomer 55LT, 1202LT PFX Special elastomer 518C N Polyamide 2010N, 2020N, 2040N (V30), 2245N, 2244N, 8LPG V NBR A-8

23 Hose and fitting selection (1) The fluid resistance tables are simplified rating tabulations based on immersion tests at 24 C. Higher temperatures tend to reduce ratings. Since final selection depends on pressure, fluid and ambient temperature and other factors not known to Parker Hannifin, no performance guarantee is expressed or implied. The indications do not imply any compliance with standards and regulations and do not refer to possible changes of colour, taste or smell. For food and drinking water specially approved materials have to be used. For fluids not listed or for advice on particular applications, please consult Parker Hannifin GmbH, polyflex Division in Hüttenfeld, Germany. (2) Hose applications for these fluids must take into account legal and insurance regulations. The chemical resistance indicated does not express or imply approval by certain institutions. (3) Satisfactory at some concentrations and temperatures, unsatisfactory at others. (4) For gas applications, the cover should be pin-pricked and the pressure must not be released quickly. Special safety guard accessories are to be used to prevent damage or personal injury in the event of failure. (5) Chemical resistance does not imply low permeation rates. Please consult Parker Hannifin GmbH for a recommendation for your specific requirements. (6) The indication of chemical resistance does not imply any special food compatibility; it refers only to the chemical resistance of the material. (7) Chemical resistance does not imply acceptability for use in airless paint spray applications. These applications require a special, electrically conductive hose. A-9

24 Hose and fitting selection Chemical H N U HF V NC O OC PFX HFR FEP TFE Acetaldehyde G L L L P L P L G G G Acetic Acid Glacial L L L L G P G L L L L G Acetone L G P P P G P P P L G G Acetylene Air (4) G G G G G G G G G G G G Ammonium Chloride G P G G G P G G G G L G Ammonium Hydroxyde L G P P L G G P L G G Anhydrous Ammonia P P P P P P P P P P P Aniline P P P P P P L P P P G G Animal Oils (6) G G G G G G P P G G G Aromatic Hydrocarbons L G L L P G P L L G Asphalt G G G G G G L L G G L G Baygon (insecticide) L G P P P L G Beer G G G G G G G G G G G Benzene L G L L P L P P L L G G Biopetroleum * * * * * * * * * * * * Brake Fluid (DOT #3) G P P P P P P G Butane (2) (4) G G L L L P L P L G Butter (6) G G G G G G G G G G Calcium Chloride G G G L G G G G G G Carbon Dioxide (4) G G G G G G G G G G Carbon Monoxide (4) G G G G L G G Carbon Tetrachloride L G P P L G P P P L G G Castor Oil G L L L G L P P L G G Chlordane (insecticide) L G P P P L Chlorinated Hydrocarbon Base Fluids L G L L P L L G Chlorinated Petroleum Oil G G L L L L G Chlorinated Solvents P P P L L L P P G Chlorine, Gaseous, Dry P P P P G P L P P P Chloroform P P P P P P P P P P G G Chromic Acid P P P G P L P P L G Citric Acid Solutions G G L L G G G G L G G G Crude Petroleum Oil G G G G G G P P G G G Cyclohexane (2) G G G G P P G G G G Cygon (insecticide) L G P P P L Diazion (insecticide) L G P P P L Diesel Fuel (2) G G G G L G P P G G G Diester Oils L G P P P P P P L G Enamels G G G G L L L G G G Ethanol (6) G G L L L L G G L G G Ethers L G P P L G L P P L G G Ethylene Glycol G G L L G G G G L G G G Ethylene Oxide G G L L P L L L G Fatty Acids G G G G L L G G G Formaldehyde L L P P L L G L P L G G Formic Acid J P P P P G P G G P P G G A-10

25 Hose and fitting selection Chemical H N U HF V NC O OC PFX HFR FEP TFE Freon 12 (5) P G L L G G L L P Freon 22 (5) P G L L G G L L P Fruit Juices G G G G G G G G G G Fuel Oil (2) G G L L L G P P L G G G Gas (Oil) (2) G G G G G G P P G G G Gasoline G G P G P P G G G Glue Glycerine G G L L G G G G L G G G Glycols (to 135 F) G G L L G G L G G G Grease (petroleum base) G G G L G G L L G G G Heptachlor (insecticide) L G P L L P P P L G Hexane (2) G G G L L G P P G G G G Houghto Safe-1000 Series (phosphate esters) L G P P G G P P P L G Houghto Safe-600 Series (hydraulic fluid) G G L L G G G L L G G Hydraulic Fluid (petroleum base) G G G G G G L L G G L G Hydraulic Fluid (phosphate ester base) L G L L L G P P P L G Hydraulic Fluid (water glycol base) G G G G L G G G G Hydraulic Oil (petroleum base) G G G G G G L P G G L G Hydrochloric Acid P L P P L P L P P P G G Hydrofluoric Acid P P P P L P L P P P G G Hydrolube (hydraulic fluid/water glycol base) G G L L G G G G L G G IRUS 902 (hydraulic fluid/water-oil emulsion) G G G G G G L P G G G Isocyanates (2) L L L L P L P L L G Isooctane (2) G G G G L G L P L G G G Isopropyl Alcohol G G L L L G G L L G G G Kerosene (2) G G L L L G L P P G G G Ketones L G P P P G G P P L G G Lacquer Solvents L G P P P L P L L G Lactic Acid P G P P G G G G P P G G Lime (calcium oxide) G G G G G G G G G G G Lindol (hydraulic fluid/phosphate esters) L G P P P L G Linseed Oil G G G G L G L P G G G G LP-Gas Lubricating Oils (diester base) L G P P G P L G Lubricating Oils (petroleum base) G G G G G G L P G G G G Magnesium Hydroxide L G L L G G G L L G G Magnesium Salts G G G G G G G Malathion (insecticide) L G P P P L G Mercury G G G G G G G G G G G G Meropa Oil (sulphur base) G G G A-11

26 Hose and fitting selection Chemical H N U HF V NC O OC PFX HFR FEP TFE Methane Methanol G G P P P G L P P G G Methoxychlor (insecticide) L G P P P L G Methyl Alcohol (6) G G P P P G L P P G G G Methyl Ethyl Ketone (MEK) L G P P P G G L P L G G Methyl Ethyl Ketone Peroxide (MEKP) L P P P G Methyl Isobutyl Ketone (MIBK) L G P P P G L P P L G G Methylene Chloride P L P P L P L P P P G G Milk (6) G G G G G G G G G G G Mineral Oil G G G G G G L P G G G G Mineral Spirits P L L P L P G Motor Oils G G G G G G G G G G Naphta L G P P P G P P P L G G Natural Gas (4) Nitric Acid P P P P L P P P P P L G Nitrobenzene P G P P P G P P P P G G Nitrogen, Gaseous (4) (5) G G G G G G G G G G G G Nitrous Oxide L G L G Oil (SAE) G G G G G G L L G G G Oil of Turpentine G G P P G G P P P G G Oleic Acid G G G G L G L L G G G G OS 45 Type 3 Hydraulic Fluid (silicate esters) L G L L P P P L L Ozone L P L L G P L G P L G G Paint (Oil Base) (7) G G G G P L P G G G Paint Solvents (Oil base) L G L L P P P L L G Pentane (2) G G L L L P P L G G G Perchloric Acid P P P P L P P P P P L G Perchloroethylene P P P P L P P P P P G Petroleum Ether P P P Petroleum Oils G G G G G G L P G G G Phenols P P P P L P P P P P G Phosphate Esters (above 135 F) P G P P P P P P L G Phosphate Esters (to 135 F) G G P P P G P P P G G Polyol Esters L G P P P P L G Potassium Hydroxide, 50% P P P P L L L P P G G Propane (4) (5) Propylene Glycol G G G G L G G Pydraul 312C, 625 (to 135 F) P G P P P G P P P G G Pydraul F-9, 150, 160 (to 135 F) G G P P P G P P P G G Quintolubric 822 Fluid G G G G Salt Water G G G Sevin (insecticides in water) G G G G G G G Silicone Greases G G G G G G G G G A-12

27 Hose and fitting selection Chemical H N U HF V NC O OC PFX HFR FEP TFE Silicone Oils G G G G G G G G G Skydrol 500 & 7000 L G P P P G P P P L G G Soap Solutions G G G G G G G G G G G G Soda Water G G G G G G G G G Sodium Borate G G G G G G G G G G G G Sodium Carbonate Sodium Chloride Solutions G G G G G G G G G G Sodium Hydroxide, 50% L P P P L P L L P L G G Sodium Hypochloride L P P P L P L G G Steam P P P P P P P P P P G G Stoddard Solvent P G P P L G P P P P G G Straight Synthetic Oils (phosphate esters) L G P P P G P L G Sulphur G G G P G L G G G G G Sulphur Dioxide P L L L L P L P G G Sulphur Hexafluoride Gas (4) (5) G G G G G G G G G Sulphuric Acid P P P P P P P P P G Toluol, Toluene L G L L P G P P P L G G Transmission Fluid G G G G P G G G G Trichlorethylene P L P P L G P P P P G G Trisodium Phosphate Solutions L G P P G G G G P L G G Turpentine G G L L L G P P P G G G Ucon (hydraulic fluid/water glycol base) G G L L G G L G G Varnish G G G G P G G L G G G Vinegar (6) L G L L G G G G L L G G Water (above 60 C) (6) P G P P L P P P P L G Water (to 60 C) (6) G G G G G G G G L G G G Water Glycols (above 60 C) P G P P L P P P P G Water Glycols (to 60 C) G G L L G G L L L G G Water in oil Emulsions (above 60 C) P G P P L P P G Water in oil Emulsions (to 60 C) G G L L G G L G G Whiskey, Wines (6) G G L L G G G G G G G G Wood Oils G G L L G G G G G Xylene L G P P P G P P P L G G Zinc Chloride G G G G G P G G G G G G A-13

28 Hose and fitting selection polyflex (page no.) SAE 100R1 (E-9) SAE 100R2 (E-22) SAE 100R3 (E-6) SAE 100R7 (E-7), (E-8), (E-10), (E-11), (E-13) SAE 100R8 (E-18), (E-19), (E-20), (E-21) SAE 100R9 / (E-25) SAE 100R14 (C-4) SAE 100R18 (E-12) ISO 3949 Typ R7 (E-7), (E-8), (E-10), (E-11), (E-13) ISO 3949 Typ R8 (E-18), (E-19), (E-20), (E-21) ISO 3949 Typ R18 (E-12) DIN EN 853-1SN (E-9), (E-16), (E-17) DIN EN 853-2SN / (E-24) DIN EN 855 Typ R7 (E-7), (E-8), (E-10), (E-11), (E-13) DIN EN 855 Typ R8 (E-18), (E-19), (E-20), (E-21) SAE J517 (E-11), (E-19), (E-21), (B-3) USCG, 46 CFR (with fire sleeve) SAE J1942 (with fire sleeve) DIN (E-19) with fire protection sleeve (G-4) AS/NZS 1869 with additional flame resistant outer cover type - (D-4) Marine steel vessels, mobile and stationary offshore drilling units FDA 21 CFR (dry food contact) HH ANSI/IAS NGV4.2-CSA ECE R110 ECE R67 (E-6), (E-9), (E-18), (E-20), (E-21), (E-22), (E-23) (E-4), (E-16), (E-17) / (E-25) (C-3), (C-4), (C-5), (C-6), (C-7), (C-12), (C-11), (C-8), (C-9), (C-10) for CO 2 applications (E-37) (D-2) & (D-2) (D-4) A-14

29 Hose and fitting selection The chart below is provided as an aid in the determination of the correct hose size. Example: At 10 gallons per minute (gal/min), what is the proper hose size within the recommended velocity range for pressure lines? Locate 10 gallons per minute in the left-hand column and 25 feet per second in the right-hand column (the maximum recommended velocity range for pressure lines). Lay a straight line across these two points. The inside diameter shown in the centre column is above -6 so we have to use -8 (1/2 ). For suction lines, follow the same procedure except use recommended velocity range for intake lines in the right-hand column. where: Q = flow in gallons per minute (gal/min & l/min) V = velocity in feet per second (f/s & m/s) d = hose inside diameter (mm & dash size) Recommended maximum velocity for suction lines Recommended maximum velocity for return lines Recommended maximum velocity for pressure lines * gallons are UK gallons Conversion factors: gal/min x = l/min feet/s x = m/s * Recommended velocities are according to hydraulic fluids of maximum viscosity 315 S.S.U. at 38 C working at room temperature within 18 and 68 C. A-15

30 Hose and fitting selection When sizing hydraulic systems, internal pressure drops must be taken into account. These pressure drops result from friction loss of the flowing hydraulic fluids. 0,1 For calculation of the pressure drop in a straight line the following pressure loss diagram can be used, when flow quantity Q and nominal size are given. The resulting pressure drop Δp applies to one metre line length. DN5 DN6 DN8 DN10 DN12 DN16 DN20 DN25 DN32 DN40 p 0,01 0,001 DN50 0, A-16

31 Hose and fitting selection For each hose type at least one fitting series is approved. Please refer to the related hose table contained in each hose description to find out which fitting series is available for the desired hose type. Each end connection in this catalogue has its own alphanumeric code. For example, the alphanumeric code for a DKOL connection with 90 elbow is "CF". Pages A-18 to A-23 show a complete overview of all end connections and the related codes. The fittings cross reference table on pages A-24 to A-26 lists the page numbers where the end connections of the different fitting series are located in this catalogue. A-17

32 Hose and fitting selection Light series Metric swivel nut Heavy series Metric swivel nut E E E C E E E C E D C B E E E E E-49 Light series E-55 Metric swivel nut E E-81 ISO E C E C B-8 45 elbow Light series Metric swivel nut E E E B-5 45 elbow Light series Metric swivel nut ISO E E E E C E B-9 90 elbow Light series Metric swivel nut E E E B E elbow Light series E-56 Metric swivel nut E E-83 ISO C E B E-55 Heavy series E-70 Metric swivel nut E E-92 ISO E E C E C elbow Heavy series Metric swivel nut ISO E E E E C E E elbow Heavy series E-84 Metric swivel nut E E-107 ISO C E B B B elbow 90 elbow B B-7 45 elbow Light series 90 elbow Light series A-18

33 Hose and fitting selection Light series ISO E E E C C E C B-10 Heavy series ISO E E E E E C E C-47 Light series E E E C E E C E D C B E E E E C E E E C E C B-14 Heavy series E E C E E E elbow E C E C B-15 DIN elbow E E D B E E E E C E C B E compact elbow E E C-50 BSP swivel nut E C E D C B-24 DIN 3852 Form A E E E C E C E C B-16 ISO B E C E C E B-17 Rigid E-101 A-19

34 Hose and fitting selection E E E C C E E C E C B-18 Rigid C B E E C E C B-20 SAE (JIC) J476A J516 UNF swivel nut 90 elbow Long drop length UNF swivel nut B E E E E C C E E E C E C B elbow UNF swivel nut E C C E C B elbow UNF swivel nut E E C C E C B C E C E C E C-53 UNF swivel nut C D B elbow UNF swivel nut C C elbow UNF swivel nut UNF male swivel C D-7 45 elbow UNF male swivel C C elbow UNF male swivel A-20

35 Hose and fitting selection Short version UNF swivel nut ISO E E C C E E B-23 Long version UNF swivel nut ISO E E E elbow UNF swivel nut ISO ISO E E C C E elbow UNF swivel nut ISO ISO E E C C E E elbow Long drop length UNF swivel nut ISO E C-26 Standard version ISO E E E elbow Standard version ISO elbow Standard version ISO Heavy series ISO E E E elbow Heavy series ISO elbow Heavy series ISO A-21

36 Hose and fitting selection B D B C B B E E E elbow 90 elbow B-24 according to NEN E C D-7 UNF swivel nut C-28 Knurled E-103 A-22

37 Hose and fitting selection C C B E E-104 acc. VW standard 39-V B-26 A-23

38 Hose and fitting selection E-61 E-80 E-87 C-18 C-30 E-101 E-109 C-42 E-126 C-52 B-18 C-30 B-19 E-62 E-110 C-42 E-126 C-52 B-20 E-62 E-63 E-77 E-80 E-88 C-19 C-31 E-95 E-102 E-110 C-43 E-127 C-53 B-21 C-20 E-111 C-43 E-127 C-53 C-22 D-3 B-23 E-71 E-83 E-93 E-106 C-35 E-117 B-19 E-111 E-112 E-112 E-72 E-84 E-93 E-107 C-36 E-118 E-51 E-58 E-74 C-15 E-96 E-99 C-38 E-120 D-7 C-48 B-11 C-23 D-7 B-17 E-64 C-20 C-44 E-128 C-54 B-22 E-64 E-89 C-21 C-44 E-128 C-54 B-22 E-109 C-41 E-125 C-51 E-58 E-74 C-16 E-97 E-99 C-21 E-78 E-103 D-5 B-27 B-12 C-24 C-24 E-113 B-12 E-113 E-114 C-22 C-23 D-6 * Push-Lok A-24

39 Hose and fitting selection B-13 B-28 E-125 B-17 E-51 E-59 E-75 E-85 C-17 E-94 E-100 E-108 C-38 E-120 C-48 B-14 B-7 B-7 B-24 C-27 E-52 E-75 C-39 E-121 C-49 B-15 E-52 E-59 E-76 E-86 C-39 E-121 C-49 B-15 E-60 E-76 E-122 C-50 E-101 E-48 E-53 E-68 C-13 E-92 E-96 E-105 C-33 E-115 D-5 C-45 B-4 E-48 E-54 E-69 B-5 E-49 E-54 E-69 B-6 E-53 E-68 E-81 E-105 E-55 E-70 E-82 E-92 E-98 E-106 C-34 E-116 C-46 E-49 E-55 E-70 E-81 E-98 C-34 E-116 C-46 B-8 E-50 E-56 E-71 E-82 C-35 E-117 B-9 E-50 E-56 E-72 E-83 C-36 E-118 B-9 E-57 E-73 E-84 C-14 C-37 E-119 C-47 B-10 E-57 E-73 E-85 E-94 E-107 C-37 E-119 C-47 E-60 E-77 E-86 C-17 E-100 C-40 E-123 C-51 B-16 B-28 B-29 E-78 E-79 E-79 B-24 E-131 E-66 E-67 C-26 * Push-Lok A-25

40 Hose and fitting selection E-66 E-90 C-25 C-32 E-67 E-91 C-26 C-32 E-131 E-65 E-89 C-25 C-31 E-102 E-129 B-23 E-130 E-65 E-90 E-129 B-25 C-27 D-7 C-28 E-103 C-28 E-108 C-40 E-122 D-6 C-50 B-26 E-104 E-104 C-29 B-25 * Push-Lok A-26

41 Push-Lok hose and fittings Push-Lok self-grip hose... B-2 Push-Lok self-grip hose, electrically non-conductive... B-3 82 series... B-4 B-1

42 Push-Lok hose and fittings Assembly with Parker Push-Lok fittings (no additional clamps required) Factory air systems, many hydraulic applications (fluid compatibility see page A-8 ff.); automotive applications for air, water, lubricating oils and antifreeze fluids. Not recommended for applications where extreme pulsations are encountered. Polyurethane One layer of high tensile synthetic fibre Polyurethane black, red, green, blue, grey -40 C up to +80 C / / / / / Colour code (xxx): BLK = black BLU = blue GRN = green GRY = grey RED = red Example: 830M-6-GRN-RL B-2

43 Push-Lok hose and fittings (complies with the requirements of the automotive industry) Especially for applications where a non-conductive hose is required (min. 5 MΩ/m), e.g. for ; factory air systems; many hydraulic applications (fluid compatibility see page A-8 ff.) Not recommended for applications where extreme pulsations are encountered. Polyurethane One layer of high tensile synthetic fibre Polyurethane orange -40 C up to +80 C / / / / / Electrically non-conductive acc. to SAE J517 (less than 50 μa leakage under 250,000 Volts per metre). B-3

44 Push-Lok hose and fittings B: Brass; C: Stainless steel; K: without plastic ring /4 M12x /4 M12x /4 M12x /4 M12x /4 M14x /4 M14x /4 M14x /4 M14x /4 M16x /4 M16x /4 M16x /8 M16x /8 M16x /8 M16x /8 M16x /8 M18x /8 M18x /8 M18x /2 M22x /2 M22x /2 M22x /2 M22x /8 M22x /8 M26x /8 M26x /4 M30x /4 M30x /4 M30x M36x M36x M36x B-4

45 Push-Lok hose and fittings B: Brass; C: Stainless steel; K: without plastic ring /4 M12x /4 M12x /4 M14x /4 M14x /4 M14x /8 M16x /8 M16x /8 M16x /8 M18x /8 M18x /2 M22x /2 M22x /8 M22x /8 M22x /8 M26x /8 M26x /4 M26x /4 M30x /4 M30x M36x B-5

46 Push-Lok hose and fittings B: Brass; C: Stainless steel; K: without plastic ring /4 M12x /4 M12x /4 M14x /4 M14x /4 M16x /4 M16x /8 M16x /8 M16x /8 M16x /8 M18x /8 M18x /8 M18x /2 M22x /2 M22x /2 M22x /8 M26x /4 M30x /4 M30x /4 M30x M36x B-6

47 Push-Lok hose and fittings B: Brass; standard version without plastic ring. When ordering with plastic ring: use Part No. without K /4 M12x /4 M14x /8 M16x /8 M18x /2 M22x B: Brass; standard version without plastic ring. When ordering with plastic ring: use Part No. without K /4 M12x /4 M14x /8 M16x /8 M18x /2 M22x B-7

48 Push-Lok hose and fittings B: Brass; Fittings with standard O-ring seals can be used for working temperatures from -30 C up to +105 C /4 M12x /4 M12x /4 M14x /4 M14x /4 M16x /8 M16x /8 M16x /8 M18x /8 M18x /2 M22x /2 M22x /8 M22x /8 M22x /8 M26x /4 M30x /4 M30x B-8

49 Push-Lok hose and fittings B: Brass; Fittings with standard O-ring seals can be used for working temperatures from -30 C up to +105 C /4 M12x /4 M14x /8 M16x /8 M18x /2 M22x /8 M26x /4 M30x Brass nipple, galvanised steel swivel nut. Fittings with standard O-ring seals can be used for working temperatures from -30 C up to +105 C /4 M12x /4 M14x /4 M16x /8 M16x /8 M16x /8 M18x /8 M18x /2 M22x /8 M26x /4 M30x B-9

50 Push-Lok hose and fittings B: Brass; C: Stainless steel; K: without plastic ring /4 M12x /4 M14x /8 M16x /8 M16x /8 M16x /8 M18x /8 M18x /8 M18x /2 M22x /2 M22x /2 M22x /2 M22x /2 M26x /8 M26x /4 M30x /4 M30x B-10

51 Push-Lok hose and fittings B: Brass; C: Stainless steel; K: without plastic ring / / / / / / / / / / / / / / / / / For assembly of progressive ring or cutting ring use the pre-assembly body. B-11

52 Push-Lok hose and fittings B: Brass; K: without plastic ring /4 M12x /4 M12x /8 M16x /8 M16x /2 M22x /2 M22x /8 M26x B: Brass; K: without plastic ring /4 M12x /4 M12x /4 M12x /8 M16x /8 M16x /2 M22x B-12

53 Push-Lok hose and fittings B: Brass; K: without plastic ring /4 M12x /4 M12x /4 M12x /4 M12x /8 M16x /8 M16x /2 M22x /2 M22x B-13

54 Push-Lok hose and fittings B: Brass; C: Stainless steel /4 1/4x /4 1/4x /4 1/4x /4 3/8x /8 3/8x /8 3/8x /8 3/8x /2 1/2x /2 1/2x /2 1/2x /8 5/8x /8 5/8x /8 3/4x /4 3/4x /4 3/4x x B-14

55 Push-Lok hose and fittings B: Brass; C: Stainless steel /4 1/4x /8 3/8x /8 3/8x /2 1/2x /2 1/2x /8 5/8x /4 3/4x x B: Brass; C: Stainless steel /4 1/4x /4 1/4x /8 3/8x /8 3/8x /2 1/2x /2 1/2x /2 5/8x /8 5/8x /8 5/8x /4 3/4x /4 3/4x x B-15

56 Push-Lok hose and fittings B: Brass /4 1/8x /4 1/4x /4 1/4x /8 1/4x /8 1/4x /8 3/8x /8 3/8x /2 1/2x /2 1/2x /8 5/8x /8 5/8x /4 3/4x /4 3/4x B-16

57 Push-Lok hose and fittings B: Brass /4 1/8x /4 1/8x /4 1/4x /4 1/4x /8 1/4x /8 1/4x /8 3/8x /8 3/8x /2 3/8x /2 1/2x /2 1/2x /8 1/2x /8 3/4x /4 3/4x /4 3/4x x B: Brass /4 1/ /8 3/ /2 1/ /8 5/ /4 3/ B-17

58 Push-Lok hose and fittings B: Brass; C: Stainless steel; SM: Metric wrench size /4 1/8x / /4 1/8x / /4 1/8x mm /4 1/4x / /4 1/4x mm /4 1/4x / /4 1/4x / /4 1/2x / /8 1/4x / /8 1/4x / /8 1/4x mm /8 3/8x / /8 3/8x / /8 3/8x mm /8 3/8x / /8 1/2x mm /8 1/2x mm /2 3/8x / /2 3/8x / /2 1/2x / /2 1/2x / /2 1/2x mm /2 1/2x / /8 1/2x mm /8 1/2x / /4 1/2x mm /4 1/2x / /4 3/4x / /4 3/4x / /4 3/4x / B-18

59 Push-Lok hose and fittings /4 1/4x / /8 1/4x / /8 3/8x / /2 1/2x / /4 3/4x /4 1.6 This fitting allows for minor movement under pressure to relieve the torsion on hose, but it is not to be used for continuous or extreme swiveling. Internal O-ring is not compatible with phosphate ester fluids. B: Brass; C: Stainless steel; K: without plastic ring; SM: Metric wrench size /4 1/4x / /4 1/4x mm /8 3/8x / /2 1/2x / /2 1/2x / B-19

60 Push-Lok hose and fittings B: Brass /4 7/16x / /4 7/16x / /8 9/16x / /8 9/16x / /2 3/4x / /2 3/4x / /4 1-1/16x / /4 1-1/16x /8 1.6 B-20

61 Push-Lok hose and fittings C: Stainless steel; SM: Metric wrench size /4 7/16x / /4 7/16x mm /4 7/16x / /4 7/16x / /4 1/2x / /4 1/2x / /4 1/2x mm /4 9/16x / /8 1/2x / /8 9/16x / /8 9/16x mm /8 9/16x mm /8 9/16x / /8 9/16x mm /8 3/4x / /8 3/4x mm /8 3/4x mm /2 3/4x / /2 3/4x / /2 7/8x /2 7/8x mm /8 7/8x /8 7/8x mm /8 7/8x /8 7/8x mm /4 1-1/16x / /4 1-1/16x mm /4 1-1/16x / /4 1-1/16x mm /4 1-1/16x / /4 1-1/16x mm /16x mm /16x mm 1.6 B-21

62 Push-Lok hose and fittings B: Brass; SM: Metric wrench size /4 7/16x / /4 7/16x mm /8 9/16x / /8 9/16x mm /2 3/4x /8 1.6 C: Stainless steel; SM: Metric wrench size /4 7/16x / /4 7/16x mm /8 9/16x / /8 9/16x mm /8 9/16x mm /2 3/4x / /2 3/4x mm /8 7/8x /4 1-1/16x / /4 1-1/16x mm 1.6 B-22

63 Push-Lok hose and fittings B: Brass /4 7/16x / /4 7/16x / /4 1/2x / /8 5/8x / /8 5/8x / /2 3/4x / /2 3/4x / /8 7/8x /8 7/8x /4 1-1/16x / /4 1-1/16x /4 1.6 SM: Metric wrench size /4 9/16x /16 11/ /8 11/16x /16 13/ /8 11/16x mm /8 13/16x mm /2 13/16x / /2 13/16x mm /8 13/16x /4 15/ /8 13/16x mm /8 1x /16 1-1/ /4 1x / /4 1-3/16x /8 1-3/8 1.6 B-23

64 Push-Lok hose and fittings B: Brass /4 M10x /4 M12x /8 M14x /8 M16x /2 M18x /2 M22x /8 M24x /4 M28x B: Brass; C: Stainless steel /4 1/8x /4 1/4x /4 1/4x /8 1/4x /8 3/8x /2 3/8x /2 1/2x /8 1/2x B-24

65 Push-Lok hose and fittings B: Brass /2 3/8x /2 1/2x /4 3/4x Fittings are delivered with ED-Seal. Working temperature from -30 C up to +105 C. C: Stainless steel / / / / / B-25

66 Push-Lok hose and fittings Brass *: Stainless steel nipple, stainless steel swivel nut **: Brass nipple, stainless steel swivel nut /4 1/4x /8 3/8x /2 1/2x /8 3/4x /4 1x B-26

67 Push-Lok hose and fittings C: Stainless steel / / / / / / / / / / / / / / / / / B-27

68 Push-Lok hose and fittings B: Brass / / / / / / / / / / Brass nipple, galvanised steel swivel nut. Standard version without plastic ring. When ordering with plastic ring: use Part No. without K /4 M12x /4 M14x /8 M16x /2 M22x B-28

69 Push-Lok hose and fittings B: Brass; C: Stainless steel; K: without plastic ring /4 M12x /8 M16x /2 M22x B-29

70 Push-Lok hose and fittings B-30

71 PTFE/Fluoropolymer hose and fittings... C-2 PTFE hose... C-3 PTFE hose acc. to SAE 100 R14... C-4 PTFE hose convoluted... C-5 PTFE hose convoluted, conductive... C-6 PTFE hose... C-7 PTFE hose with PU cover... C-8 Heavy-wall PTFE hose... C-9 PTFE hose convoluted... C-10 FEP high pressure hose... C-11 FEP high pressure hose... C-12 91N series... C-13 93N series... C-30 PC series... C-33 YX series... C-45 C-1

72 PTFE/Fluoropolymer hose and fittings PTFE (polytetrafluoroethylene) is a high performance fluoroplastic with high crystallinity and high molecular weight, discovered in 1938 by DuPont chemist, Dr. Roy J. Plunkett. PTFE is more commonly known as Teflon, the DuPont trade name for PTFE. Parker PTFE hose provides full conveyance solutions for a wide array of markets and applications because of the unique properties of PTFE. inert to virtually all chemicals applicable from -70 C up to +230 C (depending on hose type) minimizes pressure drop and deposits on hose inner surface, easy to clean convoluted designs have excellent bend radius properties low tendency to hydrolysis In the case of a PTFE hose, static electricity is caused when a nonconducting fluid flows at a high velocity through the PTFE natural core tube. When a static charge builds up in the tube of a PTFE hose, it will look for the path of least resistance to ground. If the tube is non-conductive, then the path of least resistance may be to pierce through the wall of the PTFE tube to the conductive stainless steel braid and eventually to the metal fittings and back to ground through the equipment to which the hose assembly is connected. The purpose of a static dissipating tube on the inside of the hose is to provide an acceptable path of less resistance and allow the static buildup to dissipate through the core tube to the metal fittings and eventually to ground. Parker static-dissipating hose is designated with a B after the product number. Example: Hose type 919B-6 is the static-dissipative version of hose type C-2

73 PTFE hose Medium pressure service for use with hydraulic fluids at high temperatures and aggressive chemicals in the chemical industry, surface engineering, 2-component systems. The core tube material conforms to FDA 21 CFR Polytetrafluoroethylene One braided layer of stainless steel wire -50 C up to +150 C permanent temperature +230 C at working pressures up to 2 MPa / , , YX / , , YX / , , YX / , , YX / , , YX / , , YX / , , YX , , YX C-3

74 PTFE hose Medium pressure service for use with hydraulic fluids at high temperatures, steam and aggressive chemicals in the chemical industry. Especially suitable for the food industry. The core tube material conforms to FDA 21 CFR Polytetrafluoroethylene One braided layer of stainless steel wire -54 C up to +232 C (100% working pressure at 204 C) 4.8 3/ / , , N 6.4 1/ / , , N 7.9 5/ / , , N / / , , N / / , , N / / , , N / / , , N C-4

75 PTFE hose Medium pressure service for use with hydraulic fluids at and in the chemical and other industries, when are required. The core tube material conforms to FDA 21 CFR Due to its high purity the hose can also be used in the food industry. Polytetrafluoroethylene One braided layer of stainless steel wire (AISI 304) -70 C up to +230 C / , , PC / , , PC / , , PC / , , PC / , , PC / , , PC , PC / , ) 1) Factory made assemblies only for size -20. ture increase of 1 C (Example: for 170 C the max. WP is 50% of the value indicated in the table). C-5

76 PTFE hose Medium pressure service for use with hydraulic fluids at and in the chemical and other industries, when are required. Polytetrafluoroethylene, conductive One braided layer of stainless steel wire (AISI 304) -70 C up to +230 C / , , PC / , , PC / , , PC / , , PC / , , PC / , , PC , PC / , ) 1) Factory made assemblies only for size -20. ture increase of 1 C (Example: for 170 C the max. WP is 50% of the value indicated in the table). C-6

77 PTFE hose Medium pressure service for use with hydraulic fluids at high temperatures and aggressive chemicals in the chemical industry, surface engineering, 2-component systems. The core tube material conforms to FDA 21 CFR Polytetrafluoroethylene Two braided layers of stainless steel wire -50 C up to +150 C permanent temperature +230 C at working pressures up to 2 MPa / , , PX 1) / , , PX 1) / , , PX 1) / , , PX 1) / , , YX / , , YX , , YX 1) Please refer to chapter E for the PX series fittings (page E-115 ff.). C-7

78 PTFE hose Medium pressure service for use with hydraulic fluids at high temperatures and aggressive chemicals in the chemical industry, when is required. Suitable for the food industry. The core tube material conforms to FDA 21 CFR Polytetrafluoroethylene One braided layer of stainless steel wire Polyurethane black -40 C up to +135 C 4.8 3/ / , , N 7.9 5/ / , , N / / , , N / / , , N / / , , N 40 kpa ( 5,8 psi) size kpa ( 6,8 psi) size -16. C-8

79 PTFE hose Medium pressure service for use with hydraulic fluids at high temperatures, steam and aggressive chemicals in the chemical industry, when. Suitable for the food industry. The core tube material conforms to FDA 21 CFR (except 929B). Heavy-wall polytetrafluoroethylene; 929B: conductive One braided layer of stainless steel wire -73 C up to +232 C 4.8 3/ / , , N 7.9 5/ / , , N / / , , N / / , , N / / , , N 40 kpa ( 5,8 psi) size kpa ( 6,8 psi) size -16. C-9

80 PTFE hose Medium pressure service for use with hydraulic fluids at and in the chemical and other industries, when are required. The core tube material conforms to FDA 21 CFR (except 939B). Polytetrafluoroethylene, 939B: conductive One braided layer of stainless steel wire -73 C up to +232 C / , , N / , , N / , , N / , , N , , N / , , N / , N , N 67 kpa ( 9,8 psi) size kpa ( 5,8 psi) size kpa ( 6,8 psi) size -32. C-10

81 PTFE hose Glue applications in the automotive industry and material lines for temperatures below +80 C. Fluoroethylenepropylene Two spiral layers and two open spiral layers of high tensile steel wire Polyurethane grey -40 C up to +80 C / , , NX 1) / , , NX 1) / , , NX 1) / , , NX 1) / , , NX 1) / , , NX 1) , , NX 1) 1) Please refer to chapter E for the NX series fittings (page E-105 ff.).. C-11

82 PTFE hose Fluoroethylenepropylene Two spiral layers and one braided layer of high tensile steel wire -50 C up to +150 C / , , NX 1) / , , NX 1) / , , NX 1) / , , NX 1) / , , NX 1) / , , NX 1) , , NX 1) 1) Please refer to chapter E for the NX series fittings (page E-105 ff.). C-12

83 B Fittings A For stainless steel (AISI 316) please add to the Part No. Example: 1C391N-6-4. J /16 M12x /4 M12x /4 M14x /16 M14x /16 M16x /32 M16x /32 M18x /2 M18x /2 M22x /2 M26x /8 M26x /8 M30x /8 M36x C-13

84 Fittings B A For stainless steel (AISI 316) please add to the Part No. Example: 1D091N-8-6. H /16 M12x /4 M14x /16 M14x /16 M16x /32 M16x /32 M18x /2 M18x /2 M22x /8 M26x /8 M30x /8 M36x C-14

85 Fittings B A For stainless steel (AISI 316) please add to the Part No. Example: 11D91N / / / / / / / / / / / / / C-15

86 Fittings B A For stainless steel (AISI 316) please add to the Part No. Example: 13D91N / / / / / / / / / C-16

87 Fittings B A For stainless steel (AISI 316) please add to the Part No. Example: 19291N-4-4-RD. J /16 G 1/4 1/ /4 G 1/4 1/ /16 G 3/8 3/ /32 G 3/8 3/ /2 G 1/2 1/ /8 G 3/4 3/ /8 G 3/4 3/ B A For stainless steel (AISI 316) please add to the Part No. Example: 1D991N-6-6. H /16 G 1/4 1/ /4 G 1/4 1/ /16 G 3/8 3/ /32 G 3/8 3/ /2 G 1/2 1/ /8 G 3/4 3/ /8 G 3/4 3/ C-17

88 Fittings B A For stainless steel (AISI 303) please add to the Part No. Example: 10191N-4-6. H /16 1/8-27NPTF / /16 1/4-18NPTF / /4 1/4-18NPTF / /16 1/4-18NPTF / /16 3/8-18NPTF / /32 1/4-18NPTF / /32 3/8-18NPTF / /32 1/2-14NPTF / /32 3/4-14NPTF /2 1/2-14NPTF / /8 1/2-14NPTF / /8 3/4-14NPTF / /2NPTF / /8 1 1/4-11 1/2NPTF / C-18

89 Fittings B A For stainless steel (AISI 316) please add to the Part No. Example: 10691N-5-5-RD. J /16 7/16-20UNF 1/ / /4 1/2-20UNF 5/ / /16 9/16-18UNF 3/ / /32 3/4-16UNF 1/ / /2 7/8-14UNF 5/ /8 1 1/16-12UNF 3/ / /8 1 5/16-12UNF / RD series without hexagonal ferrule. 45 B A 37 For stainless steel (AISI 316) please add to the Part No. Example: 10691N-6-6. J H /16 7/16-20UNF 1/ /8 9/ /4 1/2-20UNF 5/ /16 5/ /16 9/16-18UNF 3/ /2 11/ /32 3/4-16UNF 1/ /16 7/ /2 7/8-14UNF 5/ / /8 1 1/16-12UNF 3/ / /8 1 5/16-12UNF /4 1 1/ /8 1 5/8-12UNF 1 1/ / C-19

90 Fittings B A 30 For stainless steel (AISI 303) please add to the Part No. Example: 10791N-4-4. J H /16 1/4-18NPSM 1/ /16 3/ /16 3/8-18NPSM 3/ /8 7/ /32 1/2-14NPSM 1/ / /8 3/4-14NPSM 3/ / / /2NPSM /16 1 3/ B A E J /16 7/16-20UNF 1/ / /4 1/2-20UNF 5/ / /16 9/16-18UNF 3/ / /32 3/4-16UNF 1/ / /2 7/8-14UNF 5/ /8 1 1/16-12UNF 3/ / /8 1 5/16-12UNF / /8 1 5/8-12UNF 1 1/ C-20

91 Fittings B A E /16 7/16-20UNF 1/ / /4 1/2-20UNF 5/ / /16 9/16-18UNF 3/ / /32 3/8-16UNF 1/ / /2 7/8-14UNF 5/ /8 1 1/16-12UNF 3/ / /8 1 5/16-12UNF / B A E /16 7/16-20UNF 1/ / /4 1/2-20UNF 5/ / /16 9/16-18UNF 3/ / /32 3/4-16UNF 1/ / /2 7/8-14UNF 5/ /8 1 1/16-12UNF 3/ / /8 1 5/16-12UNF / /8 1 5/8-12UNF 1 1/ C-21

92 Fittings B A 45 J H /16 5/8-18UNF 3/ /8 3/ /8 1 1/16-14UNF 3/ / B A E J /16 5/8-18UNF 3/ / /8 1 1/16-14UNF 3/ / C-22

93 Fittings B A E J /16 5/8-18UNF 3/ / /8 1 1/16-14UNF 3/ / B A J /16 7/16-24UNF 1/ / /4 1/2-20UNF 5/ / /16 1/2-20UNF 3/ / /16 5/8-18UNF 3/ / /32 3/4-18UNF 1/ / /2 7/8-18UNF 5/ / /8 1 1/6-16UNF 3/ / C-23

94 Fittings B A E J /16 7/16-24UNF 1/ / /4 1/2-20UNF 5/ / /16 5/8-18UNF 3/ / /32 3/4-18UNF 1/ / /2 7/8-18UNF 5/ / /8 1 1/16-16UNF 3/ / B A E J /16 7/16-24UNF 1/ / /4 1/2-20UNF 5/ / /16 1/2-20UNF 5/ / /16 5/8-18UNF 3/ / /32 3/4-18UNF 1/ / /2 7/8-18UNF 5/ / /8 1 1/16-16UNF 3/ / C-24

95 Fittings A B For stainless steel (AISI 303) please add to the Part No. Example: 1JC91N-8-8. J H /16 9/16-18UNF /16 11/ /16 11/16-16UNF /8 13/ /32 13/16-16UNF /4 15/ /2 1-14UNF /8 1 1/ /2 1 3/16-12UNF /16 1 1/ /8 1 3/16-12UNF /16 1 3/ /8 1 7/16-12UNF / /8 1 11/16-12UNF /8 1 7/ /8 1 11/16-12UNF /8 1 7/ B A E J /16 9/16-18UNF 1/ / /16 9/16-18UNF 1/ / /16 11/16-16UNF 3/ / /32 13/16-16UNF 1/ / /2 1-14UNF 5/ / /8 1 3/16-12UNF 3/ / /8 1 7/16-12UNF / C-25

96 Fittings B A E J /16 9/16-18UNF 1/ / /16 11/16-16UNF 3/ / /32 13/16-16UNF 1/ / /2 1-14UNF 5/ / /8 1 3/16-12UNF 3/ / /8 1 7/16-12UNF / /8 1 11/16-12UNF 1 1/ / B A E J /16 9/16-18UNF 1/ / /4 9/16-18UNF 1/ / /4 11/16-16UNF 3/ / /16 11/16-16UNF 3/ / /16 13/16-16UNF 1/ / /32 13/16-16UNF 1/ / /2 1-14UNF 5/ / /8 1 3/16-12UNF 3/ / /8 1 7/16-12UNF / C-26

97 Fittings B A Nipple, swivel nut and ferrule stainless steel (AISI 316); stainless steel shell (AISI 303) J H /16 1/ /2 9/ /4 1/ /2 9/ /16 3/ /8 11/ /32 1/ /16 7/ /8 3/ /8 1 1/ / /8 1 1/ B A Nipple, swivel nut and ferrule stainless steel (AISI 316); stainless steel shell (AISI 303) J H /16 1/ /2 9/ /4 1/ /2 9/ /16 3/ /8 11/ /32 1/ /16 7/ /8 3/ /8 1 1/ / /8 1 1/ C-27

98 Fittings B A Nipple and swivel nut stainless steel (AISI 316); stainless steel shell (AISI 303) J /16 9/16-20UNF 1/ / /16 3/4-20UNF 3/ / /32 7/8-20UNF 1/ /8 1 5/16-20UNF 3/ /2 8.3 Stainless steel (AISI 303) /16 1/ /16 3/ /32 1/ /8 3/ / C-28

99 Fittings Stainless steel (AISI 303) / / / / / C-29

100 Fittings B A For stainless steel (nipple AISI 316, shell AISI 303) please add to the Part No. Example: 10193N-8-8. H /2 1/2-14NPTF / /8 1/2-14NPTF /4 3/4-14NPTF / /2NPTF / /4 1 1/4-11 1/2NPTF / /2 1 1/2-11 1/2NPTF /2NPTF / B A For stainless steel (nipple AISI 316, shell AISI 303) please add to the Part No. Example: 10293N-8-8. H /2 1/2-14NPTF / /4 3/4-14NPTF / /2NPTF / /4 1 1/4-11 1/2NPTF / /2 1 1/2-11 1/2NPTF /2NPTF / C-30

101 Fittings 37 B A For stainless steel (nipple AISI 316, shell AISI 303) please add to the Part No. Example: 10693N-8-8. J H /2 3/4-16UNF /8 7/ /8 7/8-14UNF /4 1 1/16-12UNF /8 1 1/ /16-12UNF /8 1 1/ /4 1 5/8-12UNF /4 1 13/ /2 1 7/8-12UNF / /2-12UNF /2 2 3/ B A For stainless steel (nipple AISI 316, shell AISI 303) please add to the Part No. Example: 1JC93N J H /16-12UNF /8 1 5/ /4 1 11/16-12UNF 1 1/ /16 1 7/ C-31

102 Fittings B A E For stainless steel (AISI 316) please add to the Part No. Example: 1J793N J /16-12UNF / /4 1 11/16-12UNF 1 1/ / B A For stainless steel (AISI 316) please add to the Part No. Example: 1J993N E J /16-12UNF / /4 1 11/16-12UNF 1 1/ / C-32

103 Fittings /4 M14x /4 M16x /16 M16x /8 M16x /8 M18x /2 M18x /2 M22x C-33

104 Fittings /4 M12x /4 M14x /4 M16x /16 M16x /16 M18x /8 M16x /8 M18x /2 M22x /8 M26x /4 M30x M36x /4 M18x /16 M20x /8 M20x /8 M22x /2 M24x /8 M30x C-34

105 Fittings /4 M12x /4 M14x /16 M16x /8 M16x /8 M18x /2 M22x /8 M26x /4 M30x M36x /4 M18x /16 M20x /8 M22x /2 M24x /8 M30x C-35

106 Fittings /8 M12x /4 M14x /16 M16x /8 M16x /8 M18x /2 M22x /8 M26x /4 M30x /4 M14x /4 M18x /16 M20x /8 M22x /2 M24x /8 M30x C-36

107 Fittings /4 M12x /4 M14x /16 M14x /16 M16x /8 M18x /8 M16x /8 M22x /2 M22x /8 M26x /4 M30x M36x /4 M16x /4 M18x /16 M20x /16 M22x /8 M22x /8 M22x /2 M24x /8 M30x /4 M36x M42x C-37

108 Fittings / / / / / / / Not recommended for new constructions. Please refer to end connections C3 or CA /4 G 1/ /16 G 3/ /8 G 3/ /8 G 1/ /2 G1/ /8 G 3/ /4 G 3/ /4 G G G 1 1/ C-38

109 Fittings /4 G 1/ /16 G 3/ /8 G 3/ /8 G 1/ /2 G 1/ /8 G 3/ /4 G 3/ G G 1 1/ /4 G 1/ /16 G 3/ /8 G 3/ /8 G 1/ /2 G 1/ /8 G 3/ /4 G 3/ G 1 1/ C-39

110 Fittings /4 G 1/ /16 G 3/ /8 G 3/ /8 G 1/ /2 G 1/ /8 G 3/ /4 G 3/ /4 G G G 1 1/ /4 G 1/ /16 G 3/ /8 G 3/ /8 G 1/ /2 G 1/ /8 G 3/ /4 G 3/ /4 G G 1 1/ C-40

111 Fittings /4 G 1/ /16 G 3/ /8 G 3/ /8 G 1/ /2 G 1/ /8 G 3/ /4 G 3/ /4 G G G 1 1/ C-41

112 Fittings /4 1/4-18NPTF /4 3/8-18NPTF /16 3/8-18NPTF /8 1/4-18NPTF /8 3/8-18NPTF /8 1/2-14NPTF /2 3/8-18NPTF /2 1/2-14NPTF /8 3/4-14NPTF /4 3/4-14NPTF / /2NPTF /2NPTF /4 1/2-20UNF /4 9/16-18UNF /16 9/16-18UNF /8 3/4-16UNF /2 7/8-14UNF /8 1 1/16-12UNF /4 1 5/16-12UNF /8-12UNF C-42

113 Fittings /4 7/16-20UNF /4 1/2-20UNF /16 9/16-18UNF /8 9/16-18UNF /8 3/4-16UNF /2 7/8-20UNF /8 1 1/16-12UNF /4 1 5/16-12UNF /8-12UNF For fittings as mentioned above, but with stainless steel nipple (AISI 303), please add to the Part No. Example: 107PC /16 1/4-18NPSM /16 1/8-27NPSM /4 1/4-18NPSM /16 3/8-18NPSM /8 3/8-18NPSM /2 1/2-14NPSM /8 3/4-14NPSM /4 3/4-14NPSM C-43

114 Fittings /4 1/2-20UNF /16 9/16-18UNF /2 7/8-14UNF /8 1 1/16-12UNF /4 1 5/16-12UNF /8-12UNF /4 1/2-20 UNF /16 9/16-18 UNF /8 3/4-16 UNF /2 7/8-14 UNF /8 1 1/16-12 UNF /4 1 5/16-12 UNF /8-12 UNF C-44

115 Fittings For fittings as mentioned above, but with stainless steel nipple (AISI 303), please add to the Part No. Example: 1C3YX /16 M12x /16 M14x /16 M16x /4 M14x /4 M16x /16 M16x /8 M16x /8 M18x /2 M18x /2 M22x /8 M26x /4 M26x /4 M30x M36x C-45

116 Fittings /16 M12x /4 M14x /4 M16x /16 M16x /8 M18x /2 M22x /8 M26x /4 M30x M36x /16 M16x /4 M16x /4 M18x /16 M20x /8 M22x /2 M24x /8 M30x /4 M36x M42x C-46

117 Fittings /16 M12x /4 M14x /16 M16x /8 M18x /2 M22x /8 M26x /4 M30x M36x /16 M16x /4 M18x /16 M20x /8 M22x /2 M24x /8 M30x /4 M36x M42x C-47

118 Fittings / / / / / / / / /16 G 1/ /4 G 1/ /16 G 3/ /8 G 3/ /8 G 1/ /2 G 1/ /8 G 3/ /4 G 3/ /4 G G G 1 1/ C-48

119 Fittings /16 G 1/ /4 G 1/ /16 G 3/ /8 G 3/ /8 G 1/ /2 G 1/ /8 G 3/ /4 G 3/ G G 1 1/ /16 G 1/ /4 G 1/ /16 G 3/ /8 G 3/ /8 G 1/ /2 G 1/ /8 G 3/ /4 G 3/ G G 1 1/ C-49

120 Fittings /4 G 1/ /16 G 3/ /8 G 3/ /2 G 1/ For fittings as mentioned above, but with stainless steel nipple (AISI 303), please add to the Part No. Example: 1U0YX /16 G 1/ /16 G 1/ /4 G 1/ /16 G 3/ /4 G 3/ /16 G 3/ /8 G 3/ /8 G 1/ /2 G 1/ /2 G 5/ /8 G 3/ /4 G 3/ /4 G G G 1 1/ C-50

121 Fittings /16 G 1/ /16 G 1/ /4 G 1/ /16 G 3/ /8 G 1/ /8 G 3/ /8 G 1/ /2 G 1/ /8 G 3/ /4 G 3/ /4 G G 1 1/ /16 G 1/ /16 G 1/ /4 G 1/ /16 G 3/ /8 G 3/ /8 G 1/ /2 G 1/ /8 G 3/ /4 G 3/ /4 G G G 1 1/ C-51

122 Fittings /16 1/8-27NPTF /16 1/4-18NPTF /4 1/4-18NPTF /4 3/8-18NPTF /16 3/8-18NPTF /8 1/4-18NPTF /8 3/8-18NPTF /2 3/8-18NPTF /2 1/2-14NPTF /8 3/4-14NPTF /4 3/4-14NPTF / /2NPTF /2NPTF ,8 3/16 7/16-20UNF , ,4 1/4 1/2-20UNF , ,9 5/16 9/16-18UNF , ,5 3/8 3/4-16UNF , ,7 1/2 7/8-14UNF , ,9 5/8 1 1/16-12UNF , ,0 3/4 1 5/16-12UNF , , /8-12UNF ,0 C-52

123 Fittings /16 7/16-20UNF /4 1/2-20UNF /16 9/16-18UNF /8 3/4-16UNF /2 7/8-14UNF /8 1 1/16-12UNF /4 1 5/16-12UNF /8-12UNF For fittings as mentioned above, but with stainless steel nipple (AISI 303), please add to the Part No. Example: 107YX /16 1/4-18NPSM /16 1/8-27NPSM /4 1/4-18NPSM /16 3/8-18NPSM /8 3/8-18NPSM /2 1/2-14NPSM /8 3/4-14NPSM /4 3/4-14NPSM C-53

124 Fittings /16 7/16-20UNF /4 1/2-20UNF /16 9/16-18UNF /8 3/4-16UNF /2 7/8-14UNF /8 1 1/16-12UNF /4 1 5/16-12UNF /8-12UNF /16 7/16-20UNF /4 1/2-20UNF /16 9/16-18UNF /8 3/4-16UNF /2 7/8-14UNF /8 1 1/16-12UNF /4 1 5/16-12UNF /8-12UNF C-54

125 Hose and fittings for alternative fuels Compressed natural gas dispense hose... D-2 55 series... E series... E-81 JJ series... D-3 Hose for mobile applications in vehicles... D-4 PX-LPG series... D-5 D-1

126 Hose and fittings for alternative fuels Dispense hose for natural gas and other gases tions, compressors, chemical plants or gas processing installations Electrically conductive polymer Two or more braided layers of high tensile synthetic fibre Polyurethane, pinpricked Red, other colours available on request -40 C up to +82 C / , , / , , / , , / , , / , , H , , H *: Only available on request 5CNG , both ends JIC 7/16 x 20 UNF, length 3 m 5CNG , both ends JIC 9/16 x 18 UNF, length 3 m 5CNG , both ends JIC 7/8 x 14 UNF, length 3 m partners acc. to ECE R 110 are to be used (see page D-3). D-2

127 Hose and fittings for alternative fuels 45 B A Stainless steel /2 3/4-16UNF 1/ Other fittings available on request. J H D-3

128 Hose and fittings for alternative fuels UV- and ozone-resistant LPG-system for cars, trucks and busses Polyamide One layer of high tensile synthetic fibre Polyamide, pinpricked; opt. flame resist. cover Type -FR(*) Black, other colours available on request -25 C up to +100 C (short time 125 C) / , PX-LPG / , PX-LPG / , PX-LPG / , PX-LPG / , PX-LPG / , PX-LPG *Improved mechanical and chemical protection through flame resistant 2 nd outer cover acc. to AS/NZS 1869 The hose assemblies are produced acc. to ECE R67 regulations and can be delivered ex factory or via certified Parker partners. For required equipment containing crimping machine for small and serial production and for certification procedure please ask your responsible Parker office. D-4

129 Hose and fittings for alternative fuels /16 10x /4 10x /16 10x Metric banjo bolt M10x1 DIN 7643 and 2 gasket rings (copper) included. Wrench size for banjo bolt: 14 mm /16 M14x /4 M14x /16 M14x D-5

130 Hose and fittings for alternative fuels /16 G1/4 1/ /4 G1/4 1/ /16 G1/4 1/ /16 M10x /4 M12x /16 7/16-20 UNF 1/4" D-6

131 Hose and fittings for alternative fuels /16 7/16-20 UNF 1/ / Swivel nut G1/4 and cutting ring (brass) included / D-7

132 Hose and fittings for alternative fuels D-8

133 Hose and fittings for hydraulic and industrial applications E-1

134 Hose and fittings for hydraulic and industrial applications Small bore hose/mini-hydraulic hose up to 21 MPa...E-3 Small bore hose/mini-hydraulic hose up to 63 MPa...E-4 E-2

135 Hose and fittings for hydraulic and industrial applications are required Polyester elastomer One braided layer of high tensile synthetic fibre Polyurethane pinpricked black -40 C up to +100 C for petroleum or synthetic hydraulic fluids / EX E-3

136 Hose and fittings for hydraulic and industrial applications are required Polyamide One braided layer of high tensile synthetic fibre Polyamide, pinpricked black -40 C up to +100 C for petroleum or synthetic hydraulic fluids / , , EX 2, / , , EX / , , EX / , , EX / , , EX / , , EX E-4

137 Hose and fittings for hydraulic and industrial applications Compact pilot line hose... E-6 Standard hydraulic hose... E-7 Medium pressure hose for aggressive fluids... E-8 Medium pressure hose with steel wire reinforcement... E-9 Refrigerant hose... E-10 Medium pressure hose, electrically non-conductive... E-11 Low temperature hose constant working pressure... E-12 Low temperature hose... E-13 E-5

138 Hose and fittings for hydraulic and industrial applications hydraulic fluids is required in hydraulic systems Polyester elastomer One braided layer of high tensile synthetic fibre Polyurethane, pinpricked black -40 C up to +100 C for petroleum, max. 57 C for synthetic hydraulic fluids and water-based hydraulic fluids / , , / , , / , , / , , / , , E-6

139 Hose and fittings for hydraulic and industrial applications Medium pressure service for general industrial and mobile hydraulic applications such as Polyester elastomer One braided layer of high tensile synthetic fibre Polyurethane, pinpricked black -40 C up to +100 C for petroleum, max. 57 C for synthetic hydraulic fluids and water-based hydraulic fluids / , , / / , , / / , , / / , , / / , , / / , , / / , , / , , /56 Also available as twinline or multiline hose, see page E-43. E-7

140 Hose and fittings for hydraulic and industrial applications Medium pressure service for general industrial and mobile hydraulic applications, especially when an improved chemical resistance is required with some hydraulic/chemical fluids. Polyamide One braided layer of high tensile synthetic fibre Polyurethane, pinpricked black -40 C up to +100 C / , , / , , / / , , / / , , / / , , / / , , / / , , /56 Also available as twinline or multiline hose, see page E-43. E-8

141 Hose and fittings for hydraulic and industrial applications Medium pressure service for general industrial and mobile hydraulic applications. Polyester elastomer One braided layer of high tensile steel wire Polyurethane black -40 C up to +121 C for petroleum, max. 57 C for synthetic hydraulic fluids and water-based hydraulic fluids / , , / / , , / / , , / / , , / / , , / / , , / / , , /56 Also available as twinline or multiline hose, see page E-43. E-9

142 Hose and fittings for hydraulic and industrial applications For applications in coolant technology for fluids such as Freon /R12/R22/R134A. Other refrigerants on request. Polyamide copolymer Two braided layers of high tensile sythetic fibre Polyurethane, pinpricked black -40 C up to +100 C / , , / / , , / / , , / / , , /56 is a registered trademark of E. I. DuPont de Nemours Co. Inc. E-10

143 Hose and fittings for hydraulic and industrial applications Medium pressure service for general industrial and mobile hydraulic applications, when lines are required, e.g.: Polyester elastomer, except -2: polyamide One braided layer of high tensile synthetic fibre Polyurethane orange -40 C up to +100 C for petroleum, max. 57 C for synthetic hydraulic fluids and water-based hydraulic fluids / , , / , , / / , , / / , , / / , , / / , , / / , , / , , / , , /56 metre). E-11

144 Hose and fittings for hydraulic and industrial applications Medium pressure service for general industrial and mobile hydraulic applications, especially for systems, e.g.:, lower temperatures. Polyester elastomer One or two braided layers of high tensile synthetic fibre Special polyester, pinpricked black -57 C up to +100 C for petroleum, max. 57 C for synthetic hydraulic fluids and water-based hydraulic fluids / , , / / , , / / , , / / , , / / , , /56 Also available as twinline or multiline hose, see page E-43. E-12

145 Hose and fittings for hydraulic and industrial applications Medium pressure service for general industrial and mobile hydraulic applications, especially for systems, e.g.: lower temperatures. Polyester elastomer, except -02: polyamide Two braided layers of high tensile sythetic fibre Special polyester, pinpricked black -57 C up to +100 C for petroleum, max. 57 C for synthetic hydraulic fluids and water-based hydraulic fluids / , , / , , / / , , / / , , / / , , / / , , / / , , /56 Also available as twinline or multiline hose, see page E-43. E-13

146 Hose and fittings for hydraulic and industrial applications High pressure hose for reusable fittings... E-15 Multi purpose hose... E-16 Standard hydraulic hose... E-17 Standard hydraulic hose... E-18 Electrically non-conductive hose... E-19 Standard hydraulic hose... E-20 Electrically non-conductive hose... E-21 Hybrid high pressure hose... E-22 High pressure hose, low volumetric expansion... E-23 Multi purpose hose... E-24 High pressure hose... E-25 E-14

147 Hose and fittings for hydraulic and industrial applications High pressure service for general industrial and mobile hydraulic applications. Especially suitable for systems, where small outer diameters are required under difficult assembly conditions. Polyamide One braided layer of high tensile synthetic fibre Polyurethane, except -025: polyamide black 40 C up to +100 C / , , AF/AB / , , AF/AB / , , AF/AB / , , AF/AB * Values are valid for 20 C. Reduced working pressure at higher temperatures: 50 C (MPa/psi) 80 C (MPa/psi) PTA / 4, / 4,060 PTA / 3, / 2,760 PTA / 2, / 2,470 PTA / 2, / 2,100 E-15

148 Hose and fittings for hydraulic and industrial applications - some hydraulic/chemical fluids. Usable due such as Polyamide black -40 C up to +100 C for petroleum or synthetic hydraulic fluids / PX / /PX / /PX / /PX / /PX / /PX / PX / PX PX / PX / PX / PX / PX / PX E-16

149 Hose and fittings for hydraulic and industrial applications tions. Polyester elastomer Polyurethane black / /PX / /PX / /PX / /PX / /PX / PX / PX PX E-17

150 Hose and fittings for hydraulic and industrial applications High pressure service for general industrial and mobile hydraulic applications as well as with gases. Usable for a wide variety of fluids due to the polyamide core tube. Version with white cover:, and therefore perfectly suited for boats and yachts. Polyamide One braided layer of high tensile aramide fibre Polyurethane, pinpricked black/white (520N-4WHT and 520N-6WHT) -40 C up to +100 C for petroleum or synthetic hydraulic fluids / , , / / , , / / , , / / , , / / , , / / , , / / , , /56 E-18

151 Hose and fittings for hydraulic and industrial applications High pressure service for general industrial and mobile hydraulic applications, where a non-conductive hose is required. Polyamide One braided layer of high tensile aramide fibre Polyurethane, not pinpricked orange -40 C up to +100 C for petroleum or synthetic hydraulic fluids / , , / / , , / / , , / / , , / / , , /56 Electrically non-conductive acc. to SAE J517 (less than 50 μa leakage under 250,000 Volts per metre). E-19

152 Hose and fittings for hydraulic and industrial applications High pressure service for general industrial and mobile hydraulic applications as well as with gases. Usable for a wide variety of fluids due to the polyamide core tube. Polyamide Multiple braided layers of high tensile synthetic fibre Polyurethane, pinpricked black -40 C up to +100 C for petroleum or synthetic hydraulic fluids / , , / , , / , , / , , / / , , / , , /58 Also available as twinline or multiline hose, see page E-43. E-20

153 Hose and fittings for hydraulic and industrial applications High pressure service for general industrial and mobile hydraulic applications, where a non-conductive hose is required. Polyamide Two braided layers of high tensile sythetic fibre Polyurethane orange -40 C up to +100 C for petroleum or synthetic hydraulic fluids / , , / , , / , , / , , / / , , / , , /58 Electrically non-conductive acc. to SAE J517 (less than 50 μa leakage under 250,000 Volts per metre). E-21

154 Hose and fittings for hydraulic and industrial applications Special pressure reinforcement construction made of steel wire/textile fibre High pressure service for general industrial and mobile hydraulic applications. frequently used as twinline hose. Polyester elastomer High tensile wire, or a combination of wire and aramide fibre Polyurethane black -40 C up to +121 C for petroleum, max. 57 C for synthetic hydraulic fluids and water-based hydraulic fluids / , , / / , , / / , , / / , , / / , , / / , , / , , /58 Also available as twinline or multiline hose, see page E-43. E-22

155 Hose and fittings for hydraulic and industrial applications High pressure service for general industrial and mobile hydraulic applications. Polyamide One or two braided layers of high tensile aramide fibre Polyurethane black -40 C up to +100 C for petroleum or synthetic hydraulic fluids / , , / / , , / / , , / / , , /56 E-23

156 Hose and fittings for hydraulic and industrial applications High pressure service for general industrial and mobile hydraulic applications as well as with gases. Usable for a wide variety of fluids due to the polyamide core tube. Polyamide; alternative -08: polyester elastomer Two spiral layers of high tensile steel wire, two open spiral layers of high tensile synthetic fibre Polyurethane black; other colours on request -40 C up to +100 C (short term +120 C) for petroleum or synthetic hydraulic fluids / , , NX / , , NX / , , X / , , X / , , X E-24

157 Hose and fittings for hydraulic and industrial applications High pressure service for general industrial and mobile hydraulic applications as well as with gases. Usable for a wide variety of fluids due to the polyamide core tube. Polyamide Two spiral layers of high tensile steel wire, one braided layer of steel wire Polyurethane; -10 and above: polyamide black -40 C up to +100 C (short term +120 C) for petroleum or synthetic hydraulic fluids / , , NX / , , NX / , , NX / , , NX / , , NX / , , NX , , NX / , , NX E-25

158 Hose and fittings for hydraulic and industrial applications General statements... E-27 Medium pressure hose... E-28 High pressure hose... E-29 PTFE hose... E-30 PTFE hose... E-31 E-26

159 Hose and fittings for hydraulic and industrial applications Hoses for airless paint spray applications require a specific assembly procedure. It is imperative to have assembly training by Parker on the individual product. The hose assembly must be silicone-free as silicone interferes with the paint spray quality. This requirement includes all the components and the testing media. The hose assemblies must be conductive in order to dissipate the electrostatic charge. The conductivity of the hose assembly must be ensured and proven (100% testing) according to the Parker specification. E-27

160 Hose and fittings for hydraulic and industrial applications Medium pressure paint spray applications. Polyamide One braided layer of high tensile steel wire Polyurethane black -40 C up to +80 C / , , PX / , , /PX / , , /PX / , , /PX / , , /PX / , , /PX / , , PX / , , PX , , PX Sizes -03, -04, and -06 also available with blue cover; please change Part No. to:, or E-28

161 Hose and fittings for hydraulic and industrial applications High pressure paint spray applications. Polyamide Two spiral layers of high tensile steel wire, two open spiral layers of synthetic fibre Polyurethane black -40 C up to +80 C / , , NX / , , NX / , , X / , , X Sizes -04, and -06 also available with blue cover; please change Part No. to:, or E-29

162 Hose and fittings for hydraulic and industrial applications Medium pressure paint spray applications. Polytetrafluoroethylene One braided layer of steel wire -50 C up to +150 C continuous temperature +230 C at working pressures up to 2 MPa / , , YX / , , YX / , , YX / , , YX / , , YX / , , YX / , , YX , , YX E-30

163 Hose and fittings for hydraulic and industrial applications Medium pressure paint spray applications. Polytetrafluoroethylene Two braided layers of steel wire -50 C up to +150 C continuous temperature +230 C at working pressures up to 2 MPa / , , PX / , , PX / , , PX / , , PX / , , YX / , , YX , , YX E-31

164 Hose and fittings for hydraulic and industrial applications... E E E-36 Hose for CO 2 fire extinguishing systems with GL approval... E-37 Hose for pre-pressurisation lines in beverage dispensing equipment... E-38 Breathing air refill hose... E-39 Compressed natural gas dispense hose... E-40 Hose for mobile applications in vehicles... E-41 E-32

165 Hose and fittings for hydraulic and industrial applications Parker thermoplastic hoses are perfectly suited for applications with industrial gases and are being used in the field for many years. When selecting hoses for industrial gases, attention should be paid to the following three criteria: 1. Due to the high-grade core tube materials Parker thermoplastic hoses are chemically resistant to most of the industrial gases, such as acetylene, propane, butane, methane, natural gas, CNG, carbon dioxide, nitrogen and inert gases (see chemical resistance table, page A-10). 2. Parker thermoplastic hoses have relatively low permeation rates, thus minimising the loss of gases. This leads to an optimisation of operational costs, and gas enrichments in the surroundings caused by permeation are minimised. 3. It is mandatory for gas applications to use perforated (pinpricked) hoses in order to avoid bubble formation in the hose cover. For further information please refer to our Engineering Standard PFDE-ES01, which is available on request at Parker Polyflex. E-33

166 Hose and fittings for hydraulic and industrial applications Based on the technical requirements noted in the introduction some hose types are particularly suited for gas applications. These hose types can be classified as follows: 1) these have pinpricked covers by default: 540N 5CNG 520N 8LPG 2010N 2020N 2) these have to be pinpricked especially for gas applications: 2040N 2370N 2245N 3) these are especially suited for aggressive fluids and/or higher temperatures: 2030T 2033T F Please use the following table to select the desired hose type by size and working pressure. E-34

167 Hose and fittings for hydraulic and industrial applications For gas applications temperature limitations must be considered. For most of the gases the above Parker hose types are suitable for temperatures up to 50 C. For higher temperatures please contact Parker Polyflex. For hose applications with gases legal and actuarial regulations must be observed. The specification of the chemical resistance does not replace approval of certain bodies or for specific applications. The user has to assume full responsibility for hose selection, testing of the application and the environmental conditions, and release for the individual application. Please refer also to the standards, approvals and certificates when selecting hoses (see page A-14). E-35

168 Hose and fittings for hydraulic and industrial applications Some hose types and sizes have approvals for specific gas applications. Please refer to the following overview: German Lloyd 2040N (-03, -04, -05, -06, -08, -10, -12, -16) E-37 PFDE-CERT01 SK Zert 2040N-04V N-04V78 E-38 PFDE-CERT18 AGA/CSA approved acc. to ANSI 4.2/ CNG D-2, E-40 PFDE-CERT04 ECE R110 5CNG-3 und -8 D-2, E-40 PFDE-CERT08 ECE R67 8LPG (-3, -4, -5, -6) D-4, E-41 PFDE-CERT07 E-36

169 Hose and fittings for hydraulic and industrial applications Flexible connections between CO 2 gas cylinder regulators and manifolds in CO 2 fire extinguishing systems and for mobile or fixed CO 2 fire extinguishers. Polyamide One braided layer of high tensile steel wire Polyurethane, pinpricked black 40 C up to +80 C / , , /PX / , , /PX / , , /PX / , , /PX / , , /PX / , , PX / , , PX , , PX Also available as twinline or multiline hose, see page E-43. E-37

170 Hose and fittings for hydraulic and industrial applications Pre-pressurisation lines for carbon dioxide, nitrogen and carbon dioxide - nitrogen mixtures in beverage dispensing equipment. Polyamide, with SK approval One braided layer of high tensile steel wire Polyurethane, pinpricked 2040N-04V74: black, 2040N-04V78: grey 40 C up to +100 C / , , PX / , , PX Also available as twinline or multiline hose, see page E-43. E-38

171 Hose and fittings for hydraulic and industrial applications Polyamide One braided layer of high tensile aramide fibre Polyurethane, pinpricked grey -40 C up to +82 C / , , / , , / , , oxygen and hydrogen! use water or air only. the requirements, it may happen that the assembled system does not fulfill the requirement Grade E. This is to be verified by the system manufacturer. E-39

172 Hose and fittings for hydraulic and industrial applications Dispense hose for natural gas and other gases tions, compressors, chemical plants or gas processing installations Electrically conductive polymer Two or more braided layers of high tensile synthetic fibre Polyurethane, pinpricked Red, other colours available on request -40 C up to +82 C / , , / , , / , , / , , / , , H , , H *: Only available on request 5CNG , both ends JIC 7/16 x 20 UNF, length 3 m 5CNG , both ends JIC 9/16 x 18 UNF, length 3 m 5CNG , both ends JIC 7/8 x 14 UNF, length 3 m partners acc. to ECE R 110 are to be used (see page D-3). E-40

173 Hose and fittings for hydraulic and industrial applications UV- and ozone-resistant LPG-system for cars, trucks and busses Polyamide One layer of high tensile synthetic fibre Polyamide, pinpricked; opt. flame resist. cover Type -FR(*) Black, other colours available on request -25 C up to +100 C (short term 125 C) / , PX-LPG / , PX-LPG / , PX-LPG / , PX-LPG / , PX-LPG / , PX-LPG *Improved mechanical and chemical protection through flame resistant 2 nd outer cover acc. to AS/NZS 1869 The hose assemblies are produced acc. to ECE R67 regulations and can be delivered ex factory or via certified Parker partners. For required equipment containing crimping machine for small and serial production and for certification procedure please ask your responsible Parker office. E-41

174 Hose and fittings for hydraulic and industrial applications Twinline and multiline hose... E-43 E-42

175 Hose and fittings for hydraulic and industrial applications Twinline or multiline hoses ensure easier installation, and especially in applications such as fork-lift trucks, aerial lifts and hydraulic cranes they form a compact unit. On request twinline and multiline hose can be joined using various combinations of hose sizes and types. For separating multiline hose and the appropriate tools see page H-27. The following hose types are available in twinline or multiline configuration: Other hose types on request. E-43

176 Hose and fittings for hydraulic and industrial applications Preform hose... E-45 Hose coils... E-45 Hose bundles... E-46 E-44

177 Hose and fittings for hydraulic and industrial applications Combines the advantages of a custom formed steel tube with the flexibility of a hose. Please contact us for individual custom solutions. Hose coils from following hose types are available: Other hose types on request. E-45

178 Hose and fittings for hydraulic and industrial applications In Parker hose bundles, multiple hoses are combined into one compact unit. Hoses with different pressure ratings and sizes can be combined. Options: hoses Advantages: E-46

179 Hose fittings 54 series... E series... E series... E series... E series... E-81 9X series... E-92 AB/AF series... E-96 EX series... E-98 NX series... E-105 PX series... E-115 E-47

180 Hose fittings /16 M12x /4 M14x /16 M16x /8 M18x /16 M12x /4 M14x /8 M18x E-48

181 Hose fittings /16 M12x /4 M14x /8 M18x /16 M12x /4 M14x /16 M16x /8 M16x /8 M18x E-49

182 Hose fittings /16 M12x /4 M14x /16 M16x /8 M16x /8 M18x /16 M12x /8 M16x E-50

183 Hose fittings / / / /4 G 1/4 1/ E-51

184 Hose fittings /16 G 1/4 1/ /4 G 1/4 1/ /8 G 3/8 3/ /16 G 1/4 1/ /4 G 1/4 1/ /16 G 3/8 3/ /8 G 3/8 3/ E-52

185 Hose fittings /16 M12x /4 M14x /16 M16x /8 M18x /2 M22x M36x B A J H /16 M16x /16 M20x /8 M22x /2 M24x E-53

186 Hose fittings /16 M12x /4 M14x /16 M16x /8 M18x /2 M22x /16 M12x /4 M14x /16 M16x /8 M18x /2 M22x E-54

187 Hose fittings /16 M12x /4 M14x /16 M16x /8 M16x /8 M18x /2 M22x /4 M26x /4 M30x M36x /16 M16x /4 M18x /16 M20x /8 M22x /2 M24x /4 M36x M42x E-55

188 Hose fittings /16 M12x /4 M14x /16 M16x /8 M18x /2 M22x /4 M26x /4 M30x /16 M12x /4 M14x /16 M16x /8 M18x /2 M22x /4 M30x M36x E-56

189 Hose fittings B A H /16 M12x /4 M14x /16 M16x /8 M18x /2 M22x /4 M26x /4 M30x B A H /16 M16x /4 M18x /16 M20x /8 M22x /2 M24x /4 M30x /4 M36x E-57

190 Hose fittings / / / / / / / / / / / / E-58

191 B Hose fittings A J H /4 G 1/4 1/ /8 G 3/8 3/ /2 G 1/2 1/ /4 G 3/4 3/ G /4 G 1/4 1/ /8 G 3/8 3/ /2 G 1/2 1/ /4 G 3/4 3/ G E-59

192 Hose fittings /4 G 1/ /8 G 3/ /2 G 1/ B A H /4 G 1/4 1/ /8 G 3/8 3/ /2 G 1/2 1/ /4 G 3/4 3/ G E-60

193 Hose fittings B A H /16 1/8-27NPTF 1/ /16 1/4-18NPTF 1/ /16 3/8-18NPTF 3/ /4 1/8-27NPTF 1/ /4 1/4-18NPTF 1/ /4 3/8-18NPTF 3/ /16 1/4-18NPTF 1/ /16 3/8-18NPTF 3/ /8 1/4-18NPTF 1/ /8 3/8-18NPTF 3/ /8 1/2-14NPTF 1/ /2 3/8-18NPTF 3/ /2 1/2-14NPTF 1/ /4 3/4-14NPTF 3/ /2NPTF E-61

194 Hose fittings B A H /16 7/16-20UNF 1/ /4 7/16-20UNF 1/ /4 1/2-20UNF 5/ /4 1/2-20UNF 3/ /16 9/16-18UNF 5/ /16 9/16-18UNF 3/ /8 9/16-18UNF 3/ /8 3/4-16UNF 1/ /2 3/4-16UNF 1/ /2 7/8-14UNF 5/ /4 1 1/16-12UNF 3/ /16-12UNF B A H /16 7/16-20UNF 1/ /4 7/16-20UNF 1/ /4 1/2-20UNF 5/ /4 9/16-18UNF 3/ /16 7/16-20UNF 1/ /16 1/2-20UNF 5/ /8 9/16-18UNF 3/ /8 3/4-16UNF 1/ /2 3/4-16UNF 1/ /2 7/8-14UNF 5/ E-62

195 Hose fittings For stainless steel (AISI 316) please add to the Part No. Example: /8 7/16-20UNF 1/ /16 7/16-20UNF 1/ /16 1/2-20UNF 5/ /4 7/16-20UNF 1/ /4 1/2-20UNF 5/ /4 9/16-18UNF 3/ /16 1/2-20UNF 5/ /16 9/16-18UNF 3/ /16 3/4-16UNF 1/ /8 9/16-18UNF 3/ /8 3/4-16UNF 1/ /2 9/16-18UNF 3/ /2 3/4-16UNF 1/ /2 7/8-14UNF 5/ /2 1 1/16-12UNF 3/ /4 1 1/16-12UNF 3/ /16-12UNF E-63

196 Hose fittings /16 7/16-20UNF 1/ /4 7/16-20UNF 1/ /4 1/2-20UNF 5/ /16 9/16-18UNF 3/ /8 9/16-18UNF 3/ /8 3/4-16UNF 1/ /2 3/4-16UNF 1/ /2 7/8-14UNF 5/ /4 1 1/16-12UNF 3/ /16-12UNF /16 7/16-20UNF 1/ /4 7/16-20UNF 1/ /4 1/2-20UNF 5/ /4 9/16-18UNF 3/ /16 9/16-18UNF 3/ /8 9/16-18UNF 3/ /8 3/4-16UNF 1/ /2 3/4-16UNF 1/ /2 7/8-14UNF 5/ /4 1 1/16-12UNF 3/ /16-12UNF E-64

197 B Hose fittings A J H /16 9/16-18UNF 1/ /4 9/16-18UNF 1/ /4 11/16-16UNF 3/ /16 9/16-16UNF 1/ /16 11/16-16UNF 3/ /8 11/16-16UNF 3/ /8 13/16-16UNF 1/ /2 13/16-16UNF 1/ /2 1-14UNF 5/ /4 1 3/16-12UNF 3/ /16-12UNF B A J H /16 9/16-18UNF 1/ /4 9/16-18UNF 1/ /4 11/16-16UNF 3/ /16 9/16-16UNF 1/ /16 11/16-16UNF 3/ /8 11/16-16UNF 3/ /8 13/16-16UNF 1/ /2 13/16-16UNF 1/ /8 1-14UNF 5/ /4 1 3/16-12UNF 3/ /16-12UNF E-65

198 Hose fittings B A H /4 9/16-18UNF 1/ /8 11/16-16UNF 3/ /8 13/16-16UNF 1/ /4 9/16-18UNF 1/ /4 11/16-16UNF 3/ /8 11/16-16UNF 3/ /8 13/16-16UNF 1/ /2 13/16-16UNF 1/ /4 1 3/16-12UNF 3/ /16-12UNF E-66

199 Hose fittings /4 9/16-18UNF 1/ /4 11/16-16UNF 3/ /16 11/16-16UNF 3/ /8 11/16-16UNF 3/ /2 13/16-16UNF 1/ /4 1 3/16-12UNF 3/ /16-12UNF /4 9/16-18UNF 1/ /8 11/16-16UNF 3/ /8 13/16-16UNF 1/ /2 13/16-16UNF 1/ /4 1 3/16-12UNF 3/ /16-12UNF E-67

200 Hose fittings /16 M12x /4 M14x /4 M16x /16 M16x /16 M18x /8 M16x /8 M18x /2 M22x /4 M26x /4 M30x M36x /16 M16x /4 M18x /16 M20x /8 M20x /8 M22x /2 M24x /4 M30x E-68

201 Hose fittings /16 M12x /4 M14x /16 M16x /8 M16x /8 M18x /2 M22x /16 M12x /4 M14x /4 M16x /16 M16x /8 M16x /8 M18x /8 M22x /2 M22x /4 M26x E-69

202 Hose fittings /16 M12x /4 M12x /4 M14x /4 M16x /16 M16x /16 M18x /8 M16x /8 M18x /2 M22x /2 M26x /4 M26x /4 M30x M36x /16 M16x /4 M16x /4 M18x /4 M20x /16 M18x /16 M20x /8 M20x /8 M22x /2 M24x /4 M30x /4 M36x E-70

203 Hose fittings /16 M12x /4 M14x /4 M16x /16 M16x /8 M16x /8 M18x /2 M22x /4 M26x /4 M30x /16 M16x /4 M18x /16 M20x /8 M20x /2 M24x E-71

204 Hose fittings /16 M12x /6 M12x /6 M14x /6 M16x /16 M16x /16 M18x /8 M16x /8 M18x /2 M22x /4 M26x /4 M30x M36x /4 M18x /16 M20x /8 M20x /2 M24x E-72

205 Hose fittings /16 M12x /4 M14x /16 M16x /16 M18x /8 M16x /8 M18x /8 M22x /2 M22x /4 M26x /4 M30x M36x /16 M16x /4 M18x /16 M20x /8 M22x /8 M24x /2 M24x /4 M30x E-73

206 Hose fittings / / / / / / / / / / Not recommended for new constructions. Please refer to end connections C3 or CA / / / / / / / / / Not recommended for new constructions. Please refer to end connections C9. E-74

207 Hose fittings /16 G 1/4 1/ /4 G 1/8 1/ /4 G 1/4 1/ /4 G 3/8 3/ /16 G 1/4 1/ /16 G 3/8 3/ /8 G 3/8 3/ /8 G 1/2 1/ /2 G 1/2 1/ /2 G 5/8 5/ /4 G 3/4 3/ G /16 G 1/4 1/ /4 G 1/4 1/ /16 G 3/8 3/ /8 G 3/8 3/ /2 G 1/2 1/ /2 G 5/8 5/ /4 G 3/4 3/ E-75

208 Hose fittings /16 G 1/4 1/ /4 G 1/4 1/ /16 G 3/8 3/ /8 G 3/8 3/ /2 G 1/2 1/ /2 G 5/8 5/ /4 G 3/4 3/ G /4 G 1/ /8 G 3/ /2 G 1/ E-76

209 Hose fittings /4 G 1/4 1/ /16 G 3/8 3/ /8 G 3/8 3/ /2 G 1/2 1/ /4 G 3/4 3/ /16 7/16-20UNF 1/ /4 7/16-20UNF 1/ /4 1/2-20UNF 5/ /4 9/16-18UNF 3/ /16 9/16-18UNF 3/ /8 9/16-18UNF 3/ /8 3/4-16UNF 1/ /2 3/4-16UNF 1/ E-77

210 Hose fittings / / / / / / / B A / / / / / / / / E-78

211 Hose fittings B A E / / / / / / / / B A E / / / / / / / / E-79

212 Hose fittings B A H /8 1/8-27NPTF 1/ /8 7/16-20UNF 1/ E-80

213 Hose fittings B A J H /16 M16x /4 M18x /16 M20x /8 M20x /8 M22x /2 M22x /2 M24x /4 M30x /4 M36x M42x /16 M12x /4 M14x /16 M16x /16 M18x /8 M16x /8 M18x /2 M22x /8 M26x /4 M26x /4 M30x M36x E-81

214 Hose fittings /16 M16x /4 M18x /16 M20x /8 M20x /8 M22x /2 M24x /8 M30x /4 M30x /4 M36x M42x /16 M12x /4 M14x /16 M16x /8 M16x /8 M18x /2 M22x /8 M26x /4 M26x /4 M30x E-82

215 Hose fittings /16 M16x /2 M24x /16 M12x /6 M14x /16 M16x /8 M16x /8 M18x /2 M22x /8 M26x /4 M26x /4 M30x M36x E-83

216 Hose fittings /16 M20x /8 M20x /2 M24x B A H /16 M12x /4 M14x /16 M16x /16 M18x /8 M16x /8 M18x /8 M22x /2 M22x /4 M26x /4 M30x M36x E-84

217 Hose fittings B A H /16 M16x /4 M18x /16 M20x /8 M22x /2 M24x /4 M30x /4 M36x M42x B A J H /16 G 1/4 1/ /4 G 1/4 1/ /16 G 3/8 3/ /8 G 3/8 3/ /2 G 1/2 1/ /2 G 5/8 5/ /4 G 3/4 3/ G E-85

218 Hose fittings /4 G 1/4 1/ /16 G 3/8 3/ /8 G 3/8 3/ /2 G 1/2 1/ /2 G 5/8 5/ /4 G 3/4 3/ G B A H /4 G 1/4 1/ /16 G 3/8 3/ /8 G 3/8 3/ /2 G 1/2 1/ /4 G 3/4 3/ G E-86

219 B Hose fittings A H /16 1/8-27NPTF 1/ /16 1/4-18NPTF 1/ /16 3/8-18NPTF 3/ /4 1/8-27NPTF 1/ /4 1/4-18NPTF 1/ /4 3/8-18NPTF 3/ /16 1/4-18NPTF 1/ /16 3/8-18NPTF 3/ /8 1/4-18NPTF 1/ /8 3/8-18NPTF 3/ /8 1/2-14NPTF 1/ /2 3/8-18NPTF 3/ /2 1/2-14NPTF 1/ /4 3/4-14NPTF 3/ /2NPTF E-87

220 Hose fittings For stainless steel (AISI 316) please add to the Part No. Example: /16 7/16-20UNF 1/ /16 1/2-20UNF 5/ /4 7/16-20UNF 1/ /4 1/2-20UNF 5/ /4 9/16-18UNF 3/ /16 1/2-20UNF 5/ /16 9/16-18UNF 3/ /8 9/16-18UNF 3/ /8 3/4-16UNF 1/ /2 9/16-18UNF 3/ /2 3/4-16UNF 1/ /2 7/8-14UNF 5/ /2 1 1/16-12UNF 3/ /4 1 1/16-12UNF 3/ /4 1 5/16-12UNF /16-12UNF E-88

221 Hose fittings /16 7/16-20UNF 1/ /4 7/16-20UNF 1/ /4 1/2-20UNF 5/ /4 9/16-18UNF 3/ /16 9/16-18UNF 3/ /8 9/16-18UNF 3/ /8 3/4-16UNF 1/ /2 3/4-16UNF 1/ /2 7/8-14UNF 5/ /4 1 1/16-12UNF 3/ /16-12UNF B A J H /16 9/16-18UNF 1/ /4 9/16-18UNF 1/ /4 11/16-16UNF 3/ /16 9/16-18UNF 1/ /16 11/16-16UNF 3/ /8 11/16-16UNF 3/ /8 13/16-16UNF 1/ /2 13/16-16UNF 1/ /2 1-14UNF 5/ /4 1 3/16-12UNF 3/ /16-12UNF E-89

222 Hose fittings B A J H /16 9/16-18UNF 1/ /4 9/16-18UNF 1/ /4 11/16-16UNF 3/ /16 9/16-18UNF 1/ /16 11/16-16UNF 3/ /8 11/16-16UNF 3/ /8 13/16-16UNF 1/ /2 13/16-16UNF 1/ /8 1-14UNF 5/ /4 1 3/16-12UNF 3/ /16-12UNF /4 9/16-18UNF 5/ /4 11/16-16UNF 3/ /8 11/16-16UNF 3/ /8 13/16-16UNF 1/ /2 13/16-16UNF 1/ /4 1 3/16-12UNF 3/ /16-12UNF E-90

223 Hose fittings /4 9/16-18UNF 1/ /4 11/16-16UNF 3/ /16 11/16-16UNF 3/ /8 11/16-16UNF 3/ /2 13/16-16UNF 1/ /4 1 3/16-12UNF 3/ /16-12UNF E-91

224 Hose fittings /8 M18x /2 M22x /8 M20x /8 M22x /2 M24x E-92

225 Hose fittings /8 M22x /2 M24x /8 M22x /2 M24x E-93

226 Hose fittings /8 M22x /2 M24x /8 G 3/ /8 G 1/ /2 G 1/ E-94

227 Hose fittings /8 9/16-18UNF /8 3/4-16UNF /2 7/8-14UNF E-95

228 Hose fittings / M12x /4 5.2 M14x /8 8.8 M18x / / / / / E-96

229 Hose fittings / / / / / / E-97

230 Hose fittings /64 M12x /64 M14x /32 M12x /64 M14x /64 M16x /8 M16x /32 M16x E-98

231 Hose fittings / / / Not recommended for new constructions. Please refer to end connections C3 or CA / / / Not recommended for new constructions. Please refer to end connections C9. E-99

232 Hose fittings /32 G 1/ /32 G 3/ /64 G 1/ E-100

233 Hose fittings /64 G 1/ /64 1/4-18NPTF /32 1/8-27NPTF /32 1/4-18NPTF E-101

234 Hose fittings /64 3/8-24UNF /64 7/16-20UNF /64 9/16-18 UNF 1/ /64 11/16-16 UNF 3/ E-102

235 Hose fittings / / /64 M16x E-103

236 Hose fittings / /64 M16x /64 M16x E-104

237 Hose fittings For fittings as mentioned above, but with stainless steel nipple (AISI 303), please add to the Part No. Example: 1C3NX /4 M14x /4 M16x /16 M16x /8 M16x /8 M18x /2 M18x /2 M22x /4 M16x /4 M18x /16 M20x /8 M22x /2 M24x /8 M30x /4 M36x M42x E-105

238 Hose fittings /4 M16x /4 M18x /16 M20x /8 M22x /2 M24x /8 M30x /4 M36x M42x /4 M52x /4 M18x /16 M20x /8 M20x /8 M22x /2 M24x /8 M30x /4 M36x M42x E-106

239 Hose fittings /4 M18x /16 M20x /8 M22x /2 M24x /8 M30x /4 M36x M42x /4 M18x /16 M20x /8 M22x /2 M24x /8 M30x /4 M36x M42x E-107

240 Hose fittings /4 G 1/ /16 G 3/ /8 G 3/ /8 G 1/ /2 G 1/ /8 G 3/ /4 G 3/ /4 G G G 1 1/ For fittings as mentioned above, but with stainless steel nipple (AISI 303), please add to the Part No. Example: 1U0NX /4 G 1/ /4 G 3/ /16 G 3/ /8 G 3/ /8 G 1/ /2 G1/ /8 G 3/ /4 G 3/ /4 G E-108

241 Hose fittings /4 G 1/ /16 G 3/ /8 G 3/ /8 G 1/ /2 G 1/ /8 G 3/ /4 G 3/ /4 G G G 1 1/ /4 G 1 1/ /4 G 1 1/ /4 1/4-18NPTF /16 3/8-18NPTF /8 3/8-18NPTF /8 1/2-14NPTF /2 1/2-14NPTF /8 3/4-14NPTF /4 3/4-14NPTF / /2NPTF /2NPTF /4-11 1/2NPTF E-109

242 Hose fittings /4 1/2-20UNF /16 9/16-18UNF /8 3/4-16UNF /2 7/8-14UNF /8 1 1/16-12UNF /4 1 5/16-12UNF /8-12UNF /4 1 7/8-12UNF /4 7/16-20UNF /4 1/2-20UNF /16 9/16-18UNF /8 9/16-18UNF /8 3/4-16UNF /2 3/4-16UNF /2 7/8-14UNF /8 7/8-14UNF /8 1 1/16-12UNF /4 1 1/16-12UNF /4 1 5/16-12UNF /16-12UNF /8-12UNF E-110

243 Hose fittings For fittings as mentioned above, but with stainless steel nipple (AISI 303), please add to the Part No. Example: 107NX /4 1/4-18NPSM /16 3/8-18NPSM /8 3/8-18NPSM /2 1/2-14NPSM /8 3/4-14NPSM /4 3/4-14NPSM / / / / E-111

244 Hose fittings / / / / / / / / E-112

245 Hose fittings / / / / / / / / E-113

246 Hose fittings / / / / E-114

247 Hose fittings For fittings as mentioned above, but with stainless steel nipple (AISI 303), please add to the Part No. Example: 1C3PX /8 M12x /16 M12x /16 M14x /16 M16x /4 M14x /4 M16x /16 M16x /8 M16x /8 M18x /2 M18x /2 M22x E-115

248 Hose fittings /16 M12x /4 M12x /4 M14x /4 M16x /16 M16x /16 M18x /8 M16x /8 M18x /2 M22x /8 M26x /4 M30x M36x /16 M14x /16 M16x /4 M18x /16 M20x /8 M20x /8 M22x /2 M24x /8 M30x /4 M36x M42x E-116

249 Hose fittings /16 M12x /4 M12x /4 M14x /16 M16x /8 M16x /8 M18x /2 M22x /8 M26x /4 M30x M36x /16 M16x /4 M18x /16 M20x /8 M22x /2 M24x /8 M30x E-117

250 Hose fittings /16 M12x /8 M12x /4 M14x /16 M16x /8 M16x /8 M18x /2 M22x /8 M26x /4 M30x M36x /16 M16x /4 M14x /4 M18x /16 M20x /8 M22x /2 M24x /8 M30x E-118

251 Hose fittings /16 M12x /4 M12x /4 M14x /16 M14x /16 M16x /16 M18x /8 M18x /8 M16x /8 M22x /2 M22x /8 M26x /4 M30x M36x /16 M16x /4 M16x /4 M18x /16 M20x /16 M22x /8 M22x /8 M22x /2 M24x /8 M30x /4 M36x M42x E-119

252 Hose fittings / / / / / / / / Not recommended for new constructions. Please refer to end connections C3 or CA /8 G 1/ /16 G 1/ /16 G 1/ /4 G 1/ /16 G 3/ /8 G 3/ /8 G 1/ /2 G1/ /8 G 3/ /4 G 3/ /4 G G G 1 1/ E-120

253 Hose fittings /16 G 1/ /4 G 1/ /16 G 3/ /8 G 3/ /8 G 1/ /2 G 1/ /8 G 3/ /4 G 3/ G G 1 1/ /16 G 1/ /4 G 1/ /16 G 3/ /8 G 3/ /8 G 1/ /2 G 1/ /8 G 3/ /4 G 3/ G 1 1/ E-121

254 Hose fittings /8 G 1/ /16 G 1/ /16 G 1/ /4 G 1/ For fittings as mentioned above, but with stainless steel nipple (AISI 303), please add to the Part No. Example: 1U0PX /8 G 1/ /16 G 1/ /4 G 1/ /16 G 3/ /4 G 3/ /16 G 3/ /8 G 3/ /8 G 1/ /2 G 1/ /8 G 3/ /4 G 3/ /4 G G G 1 1/ E-122

255 Hose fittings /8 G 1/ /16 G 1/ /16 G 1/ /4 G 1/ /16 G 3/ /8 G 3/ /8 G 1/ /2 G 1/ /8 G 3/ /4 G 3/ /4 G G 1 1/ E-123

256 Hose fittings /16 G 1/ /16 G 1/ /4 G 1/ /16 G 3/ /8 G 3/ /8 G 1/ /2 G 1/ /8 G 3/ /4 G 3/ /4 G G G 1 1/ BF: Brass C: Stainless steel (AISI 316 Ti) /4 W21.8 x 1/ /4 W21.8 x 1/ Only for CO 2 applications. E-124

257 Hose fittings BF2: Brass CS: Stainless steel (AISI 316 Ti) / x / x Only for CO 2 applications. BF: Brass C: Stainless steel (AISI 316 Ti) H /4 R1/ /4 R1/ Only for CO 2 applications. E-125

258 Hose fittings /16 1/8-27NPTF /16 1/4-18NPTF /4 1/4-18NPTF /4 3/8-18NPTF /16 3/8-18NPTF /8 1/4-18NPTF /8 3/8-18NPTF /8 1/2-14NPTF /2 3/8-18NPTF /2 1/2-14NPTF /8 3/4-14NPTF /4 3/4-14NPTF / /2NPTF /2NPTF /16 7/16-20UNF /4 1/2-20UNF /4 9/16-18UNF /16 9/16-18UNF /8 3/4-16UNF /2 7/8-14UNF /8 1 1/16-12UNF /4 1 5/16-12UNF /8-12UNF E-126

259 Hose fittings /8 7/16-20UNF /16 7/16-20UNF /4 7/16-20UNF /4 1/2-20UNF /16 9/16-18UNF /8 9/16-18UNF /8 3/4-16UNF /2 7/8-20UNF /8 1 1/16-12UNF /4 1 5/16-12UNF /8-12UNF For fittings as mentioned above, but with stainless steel nipple (AISI 303), please add to the Part No. Example: 107PX /8 1/4-18NPSM /16 1/4-18NPSM /16 1/8-27NPSM /4 1/4-18NPSM /16 3/8-18NPSM /8 3/8-18NPSM /2 1/2-14NPSM /8 3/4-14NPSM /4 3/4-14NPSM E-127

260 Hose fittings /16 7/16-20UNF /4 1/2-20UNF /16 9/16-18UNF /8 3/4-16UNF /2 7/8-14UNF /8 1 1/16-12UNF /4 1 5/16-12UNF /8-12UNF /16 7/16-20 UNF /4 1/2-20 UNF /16 9/16-18 UNF /8 3/4-16 UNF /2 7/8-14 UNF /8 1 1/16-12 UNF /4 1 5/16-12 UNF /8-12 UNF E-128

261 Hose fittings /16 9/16-18 UNF 1/ /4 9/16-18 UNF 1/ /4 11/16-16 UNF 3/ /16 9/16-18 UNF 1/ /16 11/16-16 UNF 3/ /8 11/16-16 UNF 3/ /8 13/16-16 UNF 1/ /2 13/16-16 UNF 1/ /4 1 3/16-12 UNF 3/ /16-12 UNF /16 9/16-18 UNF 1/ /4 9/16-18 UNF 1/ /4 11/16-16 UNF 3/ /16 9/16-18 UNF 1/ /16 11/16-16 UNF 3/ /8 11/16-16 UNF 3/ /8 13/16-16 UNF 1/ /2 13/16-16 UNF 1/ /4 1 3/16-12 UNF 3/ /16-12 UNF E-129

262 Hose fittings /4 9/16-18 UNF 1/ /8 11/16-16 UNF 3/ /8 13/16-16 UNF 1/ /2 13/16-16 UNF 1/ /4 1 3/16-12 UNF 3/ /16-12 UNF /16 9/16-18 UNF 1/ /4 9/16-18 UNF 1/ /4 11/16-16 UNF 3/ /16 9/16-18 UNF 1/ /16 11/16-16 UNF 3/ /8 11/16-16 UNF 3/ /8 13/16-16 UNF 1/ /2 13/16-16 UNF 1/ /4 1 3/16-12 UNF 3/ /16-12 UNF E-130

263 Hose fittings /16 9/16-18 UNF 1/ /4 9/16-18 UNF 1/ /4 11/16-16 UNF 3/ /16 9/16-18 UNF 1/ /16 11/16-16 UNF 3/ /8 11/16-16 UNF 3/ /8 13/16-16 UNF 1/ /2 13/16-16 UNF 1/ /4 1 3/16-12 UNF 3/ /16-12 UNF BF: Brass C: Stainless steel (AISI 316 Ti) /4 W21.8 x 1/ /4 W21.8 x 1/ /4 W24.32 x 1/ /4 W24.32 x 1/ Only for CO 2 applications. E-131

264 Hose fittings BF2: Brass CS: Stainless steel (AISI 316 Ti) / x / x Only for CO 2 applications. E-132

265 Accessories Bulk steel spring guards...f-2 PolyGuard anti-abrasion sleeve...f-3 ParKoil anti-abrasion sleeve...f-3 Fire protection sleeves...f-4 Special cut-to-length spring guards...f-5 Parflex CNG hose guard kit...f-6 Banjo bolt...f-6 Copper ring...f-7 Tape...F-7 F-1

266 Accessories Spring guards made of electroplated hard drawn-steel wire used to protect the hose cover from abrasion and damages F-2

267 Accessories Heavy duty polyethylene sleeves for extreme applications Cost-effective Anti-Abrasion Sleeve standard version F-3

268 Accessories The firesleeve is constructed of a uniform single braid of glass fibre with a special fire-proof outside coating. Used to protect hoses from heat, flying sparks, glowing metal scales etc. Hose clamps for mounting required F-4

269 Accessories 2040N-02V BA H/N BA N H/N BA N H/N N N H F-5

270 Accessories Use with Parflex CNG hose. Each guard kit contains two vinyl hose guards and warning tag. AM / AR Banjo bolt metric/imperial DIN 7643 Material: steel, galvanised, chromium(vi) free plated 8 M8x M10x / M12x1, M14x1, / / M16x1, / M18x1, M22x1, / M26x1, F-6

271 Accessories 8 M8x1 10 M10x1 10 1/8 12 M12x1,5 14 M14x1,5 14 1/4 16 M16x1,5 17 3/8 18 M18x1,5 22 M22x1,5 22 1/2 26 M26x1,5 Tape for regular thermoplastic hoses with wire reinforcement at normal temperatures Glass silk tape for PTFE hoses where high temperatures are applied Tape fibre reinforced tape F-7

272 Accessories F-8

273 Workshop equipment Heavy-duty hose crimper TH8-380.E...G-2 KarryKrimp 2 crimping press 85CE-06...G-3 Hand pump 85CE-0HP...G-3 Turbo air pump 85C-0AP...G-3 Power pump 82CE-0EP...G-3 PHastkrimp crimping press 89CE G-4 Parkrimp 2 crimping press 83CE...G-4 Parflex Parkrimp dies...g-5 MiniKrimp 94C-001-PFD...G-6 Hose crimping press HP-45...G-7 ST250 hose cutting tool...g-8 TH4-4 sleeve marking tool...g-8 SMM100 hose assembling machine...g-9 TH5-3 hose test rig...g hose assembling accessories...g-10 PD-1-5MM pin gauges...g-10 G-1

274 Workshop equipment Through the application of state-of-the-art innovative friction bearings, this machine is the perfect complement of the existing Parker machinery range (Parkrimp system and Polykrimp machines). The TH8-380.E is a heavy-duty crimper for crimping all Parker hose types with 4 or 6 spiral steel wire layers. Crimping force: 350 tons Control: Electronic with digital display Open/Close: High-speed up to 23 mm/s Dimensions: Length 1200 mm x width 600 mm x height 1600 mm Weight: 750 kg without oil (+ 40 l hydraulic oil) Tools: This machine is equipped with the proven PB 232 and PB 239 die systems. The intermediate die set L is supplied with the basic model. Included: Set of mirrors SHS Foot switch FU Workplace lamp LUS / LUF Options: Quick change system QDS 239 C QDS G-2

275 Workshop equipment KarryKrimp 2 is portable, compact and ruggedly built. You have everything you need to crimp hoses from DN 6 to DN32. Model 85C-061 includes crimping machine, take-apart stand, die rings and connection hose with quick coupling. For Parker hose with textile and steel wire reinforcements up to 4SP DN 32 and 4SH/100 R13 up to DN 25. Complete with hose assembly and quick coupling, 2 die rings and take-apart stand. Dimensions (with stand): H mm x W mm x J mm Weight: ca. 46 kg Working pressure: max. 70 MPa Dimensions: L 539 mm x W 417 mm x H 151 mm Weight: 11.6 kg Tank capacity: 2294 ccm Lever Force: 55 kg Working pressure: 70 MPa Dimensions: L 320 mm x W 320 mm x H 480 mm Weight: 8.4 kg Tank capacity: 662 ccm Compressed-air supply: 1/4-18NPTF thread Working pressure: 70 MPa with 3/2 hand valve Dimensions: L 320 mm x W 320 mm x H 480 mm Weight: 12 kg Tank capacity: 2000 cm 2 Connection: single phase / 230 V All pumps also suitable for KarryKrimp 82C-061. G-3

276 Workshop equipment For Parker hose with textile and steel wire braids as well as spiral steel wire layers up to DN 32. With hydraulic device and base frame, but without dies. High crimping rate. PHastkrimp crimping press with two die rings (silver and black): Electrical power: Dimensions: Weight: 400 V / 16 A H 1477 mm x W 866 mm x D 1298 mm 249 kg For Parker hose with textile and steel wire braids as well as spiral steel wire layers up to DN 50. With hydraulic device and base frame, but without dies. Complete machine with power unit, but without die sets. Bench mounted. Electrical power: 380 / 420 V KW - 50Hz Electrical connection: 16 A Dimensions: H 1130 mm x W 490 mm x D 820 mm Weight: Packed: 392 kg Unpacked: 342 kg Power unit: G-4

277 Workshop equipment Parkrimp dies are specifically engineered for Parflex hose. The die segments are linked together, and each die is well defined with identification grooves to indicate the fitting series. Also, the dies are colour coded to specify the fitting size. These dies are for use with the Parkrimp, KarryKrimp and MiniKrimp units. 1 groove 55 series / 56 series 2 grooves 58 series Parkrimp silver die ring KarryKrimp silver die ring Used with all Parflex hoses 3 grooves 91N series, 93N series Parflex dies have been designed for use with the silver die ring. See Swage and Crimp Die Selection Chart for proper crimp or swage die part number, crimp diameter on pages H-3 to H-8. G-5

278 Workshop equipment MiniKrimp is a portable, one piece crimper. Due to its light and very compact design the MiniKrimp is easy to transport and provides a cost effective way to make hose assemblies in the field. The MiniKrimp is able to crimp the following fitting series: 55/56/57/58/91N and EH of the polyflex Division product range, 43/46/48 and 26 of the HPDE product range. Patent-No and D Rating: Set-up time: Depth: Width: Height: Weight: 30 tons 20 s 127 mm 178 mm 394 mm 16 kg Name: MiniKrimp G-6

279 Workshop equipment Polyflex hose crimping press for hose sizes ranging from DN 2 to DN 20. Maximum pressing power approx. 150 t. For small batches, rubber and thermoplastic hose. The HP45 press is the preferred tool in repair shops. Dimensions: Length: Width: Height: Weight: 260 mm 200 mm 175 mm 19 kg Specifications: Theoretical pressing power: 150 t Max. aperture Ø: 44 mm Aperture travel in Ø: 19 mm Cylinder capacity: 0.28 l Number of jaws: 8 Max. working pressure: 48 MPa Working direction: perpendicular from bottom Stroke: 38 mm Name: Hose Crimping Press HP45 Special accessories Z stand carrying stand 2-level hand pump pneumatic pump with foot valve coupling hose 1 m coupling hose 1.5 m quick coupling Crimping dies: G-7

280 Workshop equipment The polyflex ST250 hose cutting tool is used for cutting off hose with metal or fibre reinforcement (up to six spiral layers) up to size DN 25. This hose cutting tool is suitable for small batches, single tubes and repair shops. Part No.: ST250 Hose cutting tool with circular blade The polyflex TH4-4 is for the permanent marking of hose assemblies or the crimp ferrule of the hose fitting. The standard model includes the table top device with base plate, height adjustable handwheel, fixable type holder, and a letter case with hardened steel type. Part no.: TH4-4 Embossing tool with type holder (for one row of type) and letter case G-8

281 Workshop equipment The polyflex SMM100 hose as sembling machine facilitates the attachment of fittings. The standard model includes electrical cabinet, foot switch, and safety three-segment chuck. The SMM 100 is suitable for fittings up to size DN 32. Part No.: SMM100 Hose assembling machine with three-segment chuck This workshop test rig is used for static pressure testing of hose assemblies ready for installation. Its test pressure ranges from 12 to 145 MPa. Almost all standard fittings can be tested. Part No.: TH 5-3 Hose Test Rig G-9

282 Workshop equipment The following accessories are recommended for proper assembly of polyflex hose assemblies. Name Hose Assembling Accessories The set contains 41 single gauges from 1.0 to 5.0 mm in steps of 0.1 mm. Material: Hardened steel Shape: AH with cylindrical head Length: 200 mm Name Pin gauges G-10

283 Technical information Mounting systems overview... H-2 Crimping diameter and tooling selection chart... H-3 Assembly procedures Reusable fittings... H-10 Assembly procedures MiniKrimp... H-14 Assembly procedures Parkrimp 2... H-19 Assembly procedures Push-Lok self-grip hose... H-26 Twinline and multiline hose separation instructions... H-27 Determining the hose length for over-the-sheaf applications... H-28 Selection, installation, and maintenance... H-29 Installation standards... H-31 Installation tips... H-33 Parker safety guide... H-34 Unit Conversion Table... H-43 H-1

284 Technical information Parker thermoplastic hoses can be processed with various crimping systems. In addition to free adjustable crimpers Parker offers the safe and functional Parkrimp system for its one-piece fittings. For mounting systems and the related assembly instructions please see the following overview. Hose type One-piece fittings: 54, 55, 56, 57, 58, 91N, 93N series two-piece fittings: 9X, EX, PC, PX, NX, YX series Parkrimp system Free adjustable crimpers Free adjustable crimpers See assembly instructions and crimp diameter charts in this chapter page H-3 ff. See assembly instructions and crimp diameter charts in this chapter page H-3 ff. The most recent assembly instructions with crimp diameter charts are available on request from H-2

285 Technical information 55 80C-P03 gray / / C-P03 gray /12.70 total length of ferrule 55 80C-P04J red / / C-P04J red /14.10 total length of ferrule 55 80C-P06 yellow / / C-P06 yellow /17.65 total length of ferrule 55 80C-P08 blue / / C-P08 blue /21.85 total length of ferrule / / C-544F red / / / / C-546F yellow / / C-548F blue / / C-P02H brown / / C-P03 gray / / C-P03 gray /12.70 total length of ferrule 55 80C-P04J red / / C-P04J red /14.10 total length of ferrule 55 80C-P05 purple / / C-P05 purple /16.25 total length of ferrule 55 80C-P06 yellow / / C-P06 yellow /17.65 total length of ferrule 55 80C-P08 blue / / C-P08 blue /21.85 total length of ferrule 58 80C-P10H orange / / C-P10H orange /25.90 total length of ferrule 55 80C-P12 green / / C-P12 green /28.45 total length of ferrule 55 80C-P16 black / / C-P16 black /34.65 total length of ferrule 55 80C-P03 gray / / C-P03 gray /12.70 total length of ferrule 55 80C-P04 red / / C-P04 red /14.75 total length of ferrule 55 80C-P05 purple / / C-P05 purple /16.25 total length of ferrule H-3

286 Technical information 55 80C-P06 yellow / / C-P06 yellow /17.65 total length of ferrule 55 80C-P08 blue / / C-P08 blue /21.85 total length of ferrule 55 80C-P03 gray / / C-P04 red / / C-P06 yellow / / C-P03 gray / / C-P03 gray /12.70 total length of ferrule 55 80C-P04 red / / C-P04 red /14.75 total length of ferrule 55 80C-P05 purple / / C-P05 purple /16.25 total length of ferrule 55 80C-P06 yellow / / C-P06 yellow /17.65 total length of ferrule 55 80C-P08 blue / / C-P08 blue /21.85 total length of ferrule 57 80C-P02H brown / / C-P03 gray / / C-P03 gray /12.70 total length of ferrule 55 80C-P04 red / / C-P04 red /14.75 total length of ferrule 55 80C-P05 purple / / C-P05 purple /16.25 total length of ferrule 55 80C-P06 yellow / / C-P06 yellow /17.65 total length of ferrule 55 80C-P08 blue / / C-P08 blue /21.85 total length of ferrule 55 80C-P12 green / / C-P12 green /28.45 total length of ferrule 55 80C-P03 gray / / C-P03 gray /12.70 total length of ferrule 55 80C-P04 red / / C-P04 red /14.75 total length of ferrule 55 80C-P05 purple / / C-P05 purple /16.25 total length of ferrule H-4

287 Technical information 55 80C-P06 yellow / / C-P06 yellow /17.65 total length of ferrule 55 80C-P08 blue / / C-P08 blue /21.85 total length of ferrule 58 80C-P10H orange / / C-P10H orange /25.90 total length of ferrule 55 80C-P12 green / / C-P12 green /28.45 total length of ferrule 55 80C-P16 black / / C-P16 black /34.65 total length of ferrule 57 80C-P02H brown / / C-P03 gray / / C-P03 gray /12.70 total length of ferrule 55 80C-P04 red / / C-P04 red /14.75 total length of ferrule 55 80C-P05 purple / / C-P05 purple /16.25 total length of ferrule 55 80C-P06 yellow / / C-P06 yellow /17.65 total length of ferrule 55 80C-P08 blue / / C-P08 blue /21.85 total length of ferrule 55 80C-P12 green / / C-P12 green /28.45 total length of ferrule 55 80C-P03 gray / / C-P03 gray /12.70 total length of ferrule 55 80C-P04 red / / C-P04 red /14.75 total length of ferrule 55 80C-P05 purple / / C-P05 purple /16.25 total length of ferrule 55 80C-P06 yellow / / C-P06 yellow /17.65 total length of ferrule 55 80C-P08J blue / / C-P08J blue /21.25 total length of ferrule 55 80C-P10 orange / / C-P10 orange /24.65 total length of ferrule 58 80C-P12H green / / C-P12H green /29.70 total length of ferrule H-5

288 Technical information 55 80C-P03 gray / / C-P03 gray /12.70 total length of ferrule 55 80C-P04 red / / C-P04 red /14.75 total length of ferrule 55 80C-P06 yellow / / C-P06 yellow /17.65 total length of ferrule 55 80C-P08 blue / / C-P08 blue /21.85 total length of ferrule 58 80C-P04H red / / C-P04H red /17.45 total length of ferrule 58 80C-P06H yellow / / C-P06H yellow /20.45 total length of ferrule 58 80C-P08H blue / / C-P08H blue /23.35 total length of ferrule 58 80C-P10H orange / / C-P10H orange /25.90 total length of ferrule 58 80C-P12H green / / C-P12H green /29.70 total length of ferrule 58 80C-P16H black / / C-P16H black /37.95 total length of ferrule 58 80C-P04H red / / C-P04H red /17.45 total length of ferrule 58 80C-P06H yellow / / C-P06H yellow /20.45 total length of ferrule 58 80C-P08H blue / / C-P08H blue /23.35 total length of ferrule 58 80C-P10H orange / / C-P10H orange /25.90 total length of ferrule 58 80C-P12H green / / C-P12H green /29.70 total length of ferrule 58 80C-P16H black / / C-P16H black /37.95 total length of ferrule H-6

289 Technical information 55 80C-P03 gray / / C-P03 gray /12.70 total length of ferrule 55 80C-P04 red / / C-P04 red /14.75 total length of ferrule 55 80C-P06 yellow / / C-P06 yellow /17.65 total length of ferrule 55 80C-P08J blue / / C-P08J blue /21.25 total length of ferrule 58 80C-P10H orange / / C-P10H orange /25.90 total length of ferrule 58 80C-P12H green / / C-P12H green /29.70 total length of ferrule 58 80C-P16J black / / C-P16J black /37.35 total length of ferrule 55 80C-P03 gray / / C-P03 gray /12.70 total length of ferrule 55 80C-P04 red / / C-P04 red /14.75 total length of ferrule 55 80C-P05 purple / / C-P05 purple /16.25 total length of ferrule 55 80C-P06 yellow / / C-P06 yellow /17.65 total length of ferrule 58 80C-P08H blue / / C-P08H blue /23.35 total length of ferrule 55 80C-P03F gray / / C-P03F gray /12.05 total length of ferrule 55 80C-P04 red / / C-P04 red /14.75 total length of ferrule 55 80C-P05F purple / / C-P05F purple /16.05 total length of ferrule 55 80C-P06 yellow / / C-P06 yellow /17.65 total length of ferrule 55 80C-P08 blue / / C-P08 blue /21.85 total length of ferrule H-7

290 Technical information 91N 80C-T04N red Note 8.50/ /4.3 91N 80C-T05N purple Note 9.80/ /4.3 91N 80C-T06N yellow Note 11.90/ /4.3 91N 80C-T08N blue Note 14.40/ /4.3 91N 80C-T10N orange Note 16.90/ /4.3 91N 80C-T12N green Note 20.00/ /5.2 91N 80C-T16N black Note 26.50/ /5.2 91N 80C-T04N red Note 8.50/ /4.3 91N 80C-T06N yellow Note 11.90/ /4.3 91N 80C-T08N blue Note 14.40/ /4.3 91N 80C-T12N green Note 20.00/ /5.2 91N 80C-T16N black Note 26.50/ /5.2 91N 80C-T04N red Note 8.50/ /4.3 91N 80C-T06N yellow Note 11.90/ /4.3 91N 80C-T08N blue Note 14.40/ /4.3 91N 80C-T12N green Note 20.00/ /5.2 91N 80C-T16H black Note 27.90/ /5.2 93N 83C-T08* blue /19.55 total length of ferrule 93N 83C-T10* orange /23.60 total length of ferrule 93N 83C-T12* green /28.20 total length of ferrule 93N 83C-T16* black /33.40 total length of ferrule 93N 83C-T20* white /40.60 total length of ferrule 93N 83C-T24* red /47.35 total length of ferrule 93N 83C-T32* green /61.70 total length of ferrule Notes: Special dies available on request. * 83C-xxx dies are suited for Parkrimp II only. H-8

291 Technical information The 54, 55, 57, 58 and 91N series fittings must be crimped over the indicated insertion depth only. The appearance after crimping is shown in the related figures below. The 56 and 93N series fittings must be crimped over the total length of the ferrule. The appearance after crimping is shown in the related figure below. In the Parkrimp system the correct insert depth ist guaranteed by using the indicated crimping die. Information given in the table are valid for steel, stainless steel and brass fittings. For the free adjustable crimpers only dies with eight segments must be used dies with six segments are not allowed. When crimping with Parkrimp presses, use the silver die ring only. The crimp diameter is to be measured in the centre of the crimping area (see figure). Crimp diameter roundness shall not vary by more than 0.25 mm. Parker reserves the right to alter crimp specifications. Appearance of 54, 55, 57 and 58 fittings series after crimping Appearance of 91N fittings series after crimping B B A Appearance of 56 and 93N fittings series after crimping A H-9

292 Technical information 1 Verify if type and size of the hose printed on the layline do match the work order. 2 a/b Using a flexible or rigid measuring tape, measure the length of hose required as follows: a. Verify required length of hose assembly with fittings. b. Subtract Cutoff Allowance of each fitting from hose assembly length. (Refer to Hose Fittings Tables for proper cutoff allowances)= dimension B Hose assembly length with fittings = 500 mm Fitting Cutoff Allowance (D0AB-12-6) 30 mm Fitting Cutoff Allowance (1DAB-12-6) 44 mm Total Cutoff Allowance 74 mm 500 mm 74 mm = 426 mm Length of hose required = 426 mm 2 c 2 d Secure hose in some type of fixture to ensure straightness. Measure and mark hose. H-10

293 Technical information 3 Using a Parflex PHC hand cutter or other sharp cutter, cut hose squarely to correct length. 4 Visually inspect both ends of hose for squareness. Remove any burrs on core tube with a sharp knife. 5 Verify if fitting part number(s) do match the work order. 6 a 6 b Inspect socket for threads in shoulder, threads in shell and damage. Inspect nipple for a through-hole, threads, hexagon and damage. Ensure swivel nut is properly crimped, has threads and turns freely. H-11

294 Technical information 7 Using an SAE 20 lubricating oil, lightly lubricate inside and outside of hose end. 8 Using a Parker VBS or VBL vice block, place hose in proper hole of vice block and place in bench vice. Ensure enough hose extends from vice block to install socket. 9 & 10 Using a wrench, screw socket onto hose counterclockwise until it bottoms. Ensure end of hose is against inside shoulder. Back off socket 1/4 turn clockwise. 11 & 12 Remove vice block and hose from vice. Place hexagon portion of socket into vice and tighten vice. Ensure socket extends past vice jaws enough to allow for installation of nipple. H-12

295 Technical information 13 Using an SAE 20 lubricating oil, generously lubricate nipple threads and hose ID. 14 Using a wrench on the nipple hexagon, screw nipple into socket clockwise until nipple bottoms against socket shoulder. 15 & 16 Measure and verify hose assembly length matches work order. Pressure test hose assembly if required. H-13

296 Technical information 1 Verify if type and size of the hose printed on the layline do match the work order. 2 a/b Using a flexible or rigid measuring tape, measure the length of hose required as follows: a. Verify required length of hose assembly with fittings. b. Subtract Cutoff Allowance of each fitting from hose assembly length. (Refer to Hose Fittings Tables for proper cutoff allowances)= dimension B Hose assembly length with fittings = 500 mm Fitting Cutoff Allowance (1B ) 36 mm Fitting Cutoff Allowance (2D ) 27 mm Total Cutoff Allowance 63 mm 500 mm 63 mm = 437 mm Length of hose required = 437 mm 2 c 2 d Secure hose in some type of fixture to ensure straightness. Measure and mark hose. H-14

297 Technical information 3 Using a Parflex PHC hand cutter or other sharp cutter, cut hose squarely to correct length. 4 Visually inspect both ends of hose for squareness. Remove any burrs on core tube with a sharp knife. 5 & 6 Verify if fitting part number(s) do match the work order. Visually inspect fitting(s) for a through-hole, threads and damage. 7 Mark hose end with proper insertion depth line. (Insertion depth = dimension A minus B according to hose fitting tables in chapters B to E) H-15

298 Technical information 8 Using an SAE 20 lubricating oil, lightly lubricate inside of hose end. (Use non-oil based soap solution for oxygen service.) 9 Push hose into fitting all the way to depth insertion mark. (If fitting does not readily slide onto hose, perform the next step.) 10 a Tap fitting onto hose as follows: Using Parker VBS or VBL vice blocks, place hose with fitting into proper hole of vice block and place in bench vice. 10 b& 11 Using a rubber mallet, tap fitting onto hose until bottom of fitting shell is aligned with depth insertion mark. Repeat Steps 7-10 for other end of hose if required. H-16

299 Technical information Select proper die set. For Parflex -/polyflex hose see Hose Crimp Assembly Tool Selection Chart in this manual. Die sets are colour coded by size Using a molybdenum disulfide type grease, apply a thin layer of grease to the die bowl. Place selected die set into the bowl Place proper die ring on top of the selected die set. See Hose Crimp Assembly Tool Selection Chart in this manual for proper die ring selection Slide pusher into place onto shoulder bolt Position the hose and fitting in dies from below. 6. Align fitting so that the shell rests on die step. H-17

300 Technical information Open functional switch (4) on the pump and close the shut-off valve (5) While holding hose and fitting into position on the step, begin pumping hand pump until die ring contacts base plate Release pressure by opening the shut-off valve (5) and remove finished assembly. Check crimp diameter Measure crimp diameter of each fitting at the top, middle and bottom of the shell. Take measurements at a minimum of three places around the shell circumference. Verify crimp diameter is within tolerances. For Parflex hoses see Parflex Hose Crimp Assembly Tool Selection Chart in this manual. H-18

301 Technical information 1 Verify if type and size of the hose printed on the layline do match the work order. 2 a/b Using a flexible or rigid measuring tape, measure the length of hose required as follows: a. Verify required length of hose assembly with fittings. b. Subtract Cutoff Allowance of each fitting from hose assembly length. (Refer to Hose Fittings Tables for proper cutoff allowances)= dimension B Hose assembly length with fittings = 500 mm Fitting Cutoff Allowance (1B ) 36 mm Fitting Cutoff Allowance (2D ) 27 mm Total Cutoff Allowance 63 mm 500 mm 63 mm = 437 mm Length of hose required = 437 mm 2 c 2 d Secure hose in some type of fixture to ensure straightness. Measure and mark hose. H-19

302 Technical information 3 Using a Parflex PHC hand cutter or other sharp cutter, cut hose squarely to correct length. 4 Visually inspect both ends of hose for squareness. Remove any burrs on core tube with a sharp knife. 5 & 6 Verify if fitting part number(s) do match the work order. 7 Mark hose end with proper insertion depth line. (Insertion depth = dimension A minus B according to hose fitting tables in chapters B to E) H-20

303 Technical information 8 Using an SAE 20 lubricating oil, lightly lubricate inside of hose end. (Use soap solution for oxygen service.) 9 Push hose into fitting all the way to depth insertion mark. (If fitting does not readily slide onto hose, perfrom the next step.) 10 a Tap fitting onto hose as follows: Using Parker VBS or VBL vice blocks, place hose with fitting into proper hole of vice block and place in bench vice. 10 b& 11 Using a rubber mallet, tap fitting onto hose until bottom of fitting shell is aligned with depth insertion mark. Repeat Steps 7-10 for other end of hose if required. H-21

304 Technical information 12 With pusher in full up position, position rear half of split die ring in rear of pusher. Lock ring in position by pushing in slide pin. 13 Install adaptor bowl in base plate of crimper for hose sizes 4 through Using a molybydendum disulfide type grease, apply a thin layer of grease on inside of adaptor bowl Select proper Par krimp die set. (See Swage and Crimp Die Selection Chart in this catalog section for proper part number selection.) Place die set into bowl. H-22

305 Technical information 17 Lower rear half of split die ring onto dies by pulling slide pin forward. 18 Insert front half of split die ring aligning pin in rear half with hole in front half Insert hose and fitting from bottom of crimper and up through die. Position fitting so bottom of fitting shell rests on die step. Press ON switch to turn on pump. H-23

306 Technical information 21 While holding hose and fitting in position on die step, lower pusher by pulling valve handle forward. 22 Crimp fitting onto hose until die ring contacts base plate. 23 Push valve handle towards the rear to retract pusher and open die set. 24 & Remove hose assembly and die set. Repeat Steps for the other end of hose if required. Press OFF switch to turn off pump. H-24

307 Technical information 27 Measure and verify if the hose assembly length matches the work order. 28 Inspect depth insertion mark at fitting ends. Insertion mark must be visible and within 3 mm of bottom of fitting shell. 29 & 30 Measure crimp diameter of each fitting at top, middle and bottom of shell. Take measurements at a minimum of three places around shell circumference. Verify crimp diameter is within tolerances. (See Crimp Specification & Tool Selection Chart in this catalog section for proper crimp diameters.) Pressure test hose assembly if required. H-25

308 Technical information 1. Cut hose perpendicularly with a sharp knife. If necessary, lubricate fitting end with water or soap and water solution (5% liquid soap + 95% water) for ease of assembly. 2. Insert fitting into hose and push with steady force until fitting is completely in hose. Grip hose approximately 2.5 cm from end. As an alternative, use the Parker G assembly tool. Push-Lok fittings will provide an effective grip only when the Push-Lok hose is pushed fully onto the insert, where the cropped end of the hose should be fully concealed by the plastic collar. Lubricate fitting end with water, soap, or a Push-Lok assembly oil. 1. Cut the hose longitudinally along a line at approximately a 20 angle from the centre line of the hose. Make sure not to nick the barbs of the fitting. 2. Pull fitting out of hose. Before reusing the fitting, check fitting for damages. Damaged fittings result in leakage. For easy assembly of Parker self-gripping hose. Overall length: approx. 320 mm Weight: approx. 2.2 kg H-26