Greenheck Product Category

Transcription

1 reenheck Product ategory SW elt rive ackward nclined une 008

2 SW elt rive Utility ans reenheck s backward inclined utility fans have many advantages; higher operating efficiencies, non overloading horsepower curve and higher pressure capability. You will also receive the following benefits with a reenheck backward inclined utility fan. M lass 1 Performance on Series 00 (sizes 10 through 36) Performance ranges from 70 to 30,000 cfm (10 to 51,000 m 3 /hr) with static pressure up to 5 in. wg (150 Pa) Two different series of construction will meet your exact needs in the most efficient manner ach fan is tested prior to shipment to provide you with smooth, vibration free operation reenheck utility fans are designed, engineered and tested to provide years of dependable service with minimal maintenance ach fan size has been tested in our M ccredited Laboratory and all models are licensed to bear the M air performance seal. Performance as cataloged is assured. reenheck an orporation certifies that the model SW fans shown herein are licensed to bear the M Seal. The ratings shown are based on tests and procedures performed in accordance with M Publication 11 and comply with the requirements of the M ertified Ratings Program. The certified ratings for SW are shown on pages 13 to 38. Series 100 and 00 SW models are listed for electrical (UL/cUL 705) ile no Series 00 SW models are listed for grease removal (UL/cUL 76) ile no. M11745 Series 00 SW models are listed for mergency Smoke ontrol Systems ile No. M17511 Quick elivery and Quick uild Programs Leading dge Technical Support More than five SW configurations are stocked in our strategically located reenheck warehouses. ll SW sizes are available through our five and ten day Quick uild (Q) programs. The Q programs provide custom built to order products available to ship in one, three, five, or ten days after ordered. This allows the flexibility of knowing that your fan can be made to order and shipped in as little as one day. Other products are available from our Quick elivery (Q) program. The Q program provides same day shipment of reenheck product from our strategically located warehouses throughout the world. When you need extensive product information look no further. reenheck products are supported by the industry s best product literature, ranging from atalogs, nstallation, Operation and Maintenance Manuals (OM s), lectronic Media, omputer ided Product Selection (PS) program and more. You ll also find this information on our website at ount on personal service and expertise from our national and international representative organizations To locate your nearest reenheck representative, call or visit our website at

3 World lass Manufacturing reenheck s skilled production workers use cost-effective machines and unique dies designed and built by our own engineers to add innovative features and greater strength to our centrifugal exhaust fans. Our advanced manufacturing processes and quality control procedures always ensure the highest product quality. nd just to be sure you get the peace-of-mind you expect when you specify reenheck, our assembly inspectors test run and monitor every fan before it leaves the factory. Results of these tests are kept in permanent records for future reference. Outstanding ustomer Service Your local reenheck representative has a wealth of industry and product knowledge to answer your questions. Our representatives receive the latest product information and can have orders processed directly to our factory. With our direct order processing system, we can ship orders as fast as the next day. With reenheck s experienced staff, we can answer questions and provide solutions. ode The model number code is designed to completely identify the fan. The correct code letters must be specified to designate the correct construction. The remainder of the model number is determined by the size and performance. SW W - T SW - elt rive Series alvanized onstruction 00 - Permatector TM oated Steel onstruction an Size 06 through 36 Motor P 4 = 1/4 15 = 11/ 75 = 71/ 3 = 1/3 0 = 100 = 10 5 = 1/ 30 = = 15 7 = 3/4 50 = 5 00 = 0 10 = 1 ischarge Position U - Upblast TU - Top ngular Upblast T - Top orizontal T - Top ngular ownblast - ownblast - ackward ngular ownblast - ackward orizontal U - ackward ngular Upblast Wheel Rotation W - lockwise W - ounterclockwise 3

4 Two onstruction Series SW Series 00 SW Series 100 reenheck s model SW Series 100 backward inclined utility fans are available in ten sizes (106 through 14) with capacities from 100 to 8,800 cfm (170 to 15,000 m 3 /hr) and static pressures to 3.5 in. wg (870 Pa). lower scroll constructed of galvanized steel rive frame is coated with PermatectorTM luminum wheel on all sizes lockwise and counterclockwise wheel rotation reenheck s model SW Series 00 backward inclined utility fans are available in sixteen sizes (06 through 36) with capacities from 70 to 7,000 cfm (10 to 45,880 m 3 /hr) and static pressures to 5 in. wg (150 Pa). ntire fan is constructed of steel and is coated with PermatectorTM Larger shafts, bearings and increased material thickness luminum wheel on sizes 06 through 10 Steel wheel on sizes 1 through 36 lockwise and counterclockwise wheel rotation vailable in either seam or welded scrolls 4 Standard onstruction eatures SW rrangement 10, single width, backward inclined utility fans feature: 1 inish - ll structural steel parts are phosphate treated and coated with reenheck s Permatector TM for a long lasting finish. ousing - onstructed of heavy gauge steel. Series 100 housings are constructed from galvanized steel. Series 00 fans are constructed of steel and are coated with Permatector TM. They are available in clockwise or counterclockwise rotation and are field rotatable to the eight standard discharge positions. ousing sides are bonded to the fan scroll with an airtight lock seam. 3 ousing Supports - ousing supports are constructed of structural steel with formed flanges for extra strength. 4 Mounting oles - ousing supports have prepunched mounting holes which provide ease for installation. 5 rive rame - Rugged, welded steel drive frame members support the shaft and bearings and provide rigid reinforcement for the housing. 6 asteners - orrosion resistant fasteners are used to secure unit base and blower scroll assembly. 7 Motor - eavy duty ball bearing motors are carefully matched to the fan load. Open drip proof, totally enclosed and explosion proof enclosures are available. 8 Motor Plate - pivoting motor plate with adjusting screws make belt tensioning a quick and easy operation. 9 Wheel - ackward inclined wheels are constructed of heavy gauge, single thickness blades are securely riveted or welded to a heavy gauge backplate and wheel cone. ach wheel is statically and dynamically balanced to precise tolerances. 10 rive ssembly - Sized for a minimum of 150% of driven horsepower. Machined cast iron pulleys are factory set to the required RPM and are adjustable for final system balancing. 11 an Shaft - Precision turned, ground and polished solid steel shafts are sized so the first critical speed is at least 5% over the maximum operating speed. Stainless steel shafts are available on SW Series 00 fans. 1 earings - eavy duty, self aligning pillow block ball bearings are selected for a minimum L 10 life in excess of 100,000 hours (L 50 average life of 500,000 hours) at maximum cataloged operating conditions. 13 nlet one - The streamlined inlet cone design provides a low turbulence air intake. This reduces intake losses and sound levels.

5 Standard onstruction eatures

6 Temperature Options Operating Temperatures - SW is suitable for applications above normal operating temperatures of 70 (1 ). Refer to the chart at the right for operation temperature guidelines and optional accessories. igh Temperature/mergency Smoke ontrol The Series 00 sizes 1 and larger may be equipped for emergency smoke removal applications by specifying a high temperature option. The table to the right indicates the construction features included in the high temperature options enabling exhaust of heat and smoke at 500 (60 ) for a minimum of 4 hours or 1000 (538 ) for a minimum of 15 minutes. igh temperature testing was conducted at reenheck s Research and evelopment facility with airstream temperatures in excess of 1000 (538 ). Temperatures were monitored at the following critical locations throughout the tests: bearings, bearing compartment, motor, motor compartment, airstream, and fan housing. igh Temperature Option 500 (60 ) for a minimum of 4 hours 1000 (538 ) for a minimum of 15 minutes Temperature ratings tested in accordance to UL smoke control systems. mergency Smoke ontrol - U.L. Listed 500 (60 ) for a minimum of 4 hours 1000 (538 ) for a minimum of 15 minutes Operation Temperature and onstruction -0 to 00 (-9 to 93 ) Standard 01 to 300 (94 to 149 ) eat Slinger / Shaft Seal 301 to 400 (149 to 04 ) eat Slinger / Shaft Seal Series 100 alvanized Painted Steel Series 00 luminum irstream The maximum continuous operating temperature on the SW is 400. or continuous operating temperatures between 401 and 1000 use an rrangement 1, 9 or 10, backward inclined centrifugal fan model SW. eatures igh Temperature Option igh Temperature Option with UL Steel onstruction Shaft Seal eat Slinger Weatherhood UL Label (Power ventilators for smoke control systems) ode mergency Smoke Temperature and Time uidelines lass Tested Temperature onverted Temperature Time (ours) R 500 (60 ) 4.00 S 1000 (538 ) 0.5 S lass 150 (30 ) 5.00 lass 50 (48 ).00 lass 300 (57 ) 0.50 lass 300 (57 ) 1.00 lass 400 (75 ).00 Spark Resistant onstruction - The following M Standards apply to fan applications that may involve the handling of potentially explosive or flammable particles, fumes or vapors. M Type - ll parts in contact with the airstream are constructed of nonferrous material (aluminum). SW does not meet M Type Spark Resistant onstruction. M Type - The fan wheel is constructed of nonferrous material (aluminum). nonferrous (aluminum) rub ring surrounds the fan shaft where it passes through the fan housing. vailable on all sizes with an aluminum wheel and rub ring. M Type - The inlet cone is constructed of nonferrous material (aluminum). nonferrous (aluminum) rub ring surrounds the fan shaft where it passes through the fan housing. vailable on all sizes with an aluminum wheel and rub ring. The constructions listed minimize the potential of ferrous components making contact with each other that may produce sparks. owever, they do not guarantee against the potential of producing sparks. The installer must electrically ground all fan and system components. 6

7 Options and ccessories UL/cUL 76 - Series 00 SW models are listed for grease removal (UL/cUL 76). The UL/cUL 76 option includes a weatherhood, threaded drain connection and bolted access door. ndoor mounting requires the fan to have welded scroll construction. Weatherhood - Weatherhoods are available to completely cover the motor and drive compartments; protecting the shaft, bearings, motor and drive components from moisture and other adverse weather conditions. Weatherhoods are vented to provide sufficient motor cooling. rain onnection - Threaded drain connections can be provided to drain moisture from the bottom of the fan housing. rease Trap - luminum trap is designed to collect grease residue and avoid drainage onto roof surface. isposable grease absorbents are available for easy maintenance. ccess oors - ccess doors provide access for inspection & cleaning. oth bolted or hinged, quick opening access doors are available on 00 Series. Welded Scroll onstruction - Welded scroll construction is available on SW Series 00. luminum onstruction - luminum airstream option is available on SW Series 00. ampers - ravity or motorized parallel blade backdraft dampers feature sturdy galvanized frames with prepunched mounting holes, aluminum blades with felt edges and balanced design for minimal resistance to airflow. ackdraft dampers are not suitable for downblast or bottom angular downblast discharge positions. The fan must be supplied with a flanged outlet to install a backdraft damper directly to the fan. eavy duty dampers are available for high pressure applications on fans with motors equal to or greater than 71/ horsepower. isconnect Switches - wide selection of NM rated switches are available for positive electrical shutoff and safety, including: dust-tight, rainproof and corrosion-resistant. Wiring Pigtail - llows direct hook-up to the power supply eliminating field wiring to the fan. xtended Lube Lines - Lubrication lines with grease fittings are extended from shaft bearings to the base of the drive frame panel for easy bearing lubrication without disassembling the fan. nlet and Outlet uards - nlet and outlet guards are constructed of expanded metal mounted in a steel frame to provide protection for non-ducted installations. The guards can be easily removed for maintenance or inspection. langed nlet and Outlet - langes are welded to the fan and are available for damper mounting or flanged duct connections. (nlet flanges have prepunched mounting holes.) ompanion lange - The companion flange connects to the inlet or outlet flange and then attaches to the ductwork. Recommended for slip fit duct connections. nlet Vane ampers - xternal inlet vane dampers are available on model SW fans sizes and xternal vanes are mounted on the inlet flange. nlet vane dampers feature zinc plated steel blade axles, stainless steel washers and bearings. Vanes can be used for either manual or automatic operation, with controls furnished by others. Maximum operating temperature is 00 (93 ). oatings - wide variety of coatings and colors are available for decorative to acidic applications on SW Series 00. ll reenheck coatings can be found in the coatings bulletin. Permatector is our standard coating. Typically used for applications that require corrosion resistance in indoor and outdoor environments. i-pro Polyester is resistant to salt water, chemical fumes and moisture in more corrosive atmospheres. Typically used for applications that require superior chemical resistance, excellent abrasion and outdoor UV protection. This coating exceeds protective qualities of ir ried eresite and ir ry Phenolic. aked namel ecorative oatings are heat cured enamels applied either as wet paints or electrostatic powders. ustomers can choose from 16 standard decorative colors or color match any color. eat Slinger and Shaft Seal - The heat slinger is an aluminum cooling disc mounted on the fan shaft between the inboard bearing and the fan housing. The disc dissipates heat conducted along the fan shaft. The shaft seal with an aluminum rub ring is available for applications where contaminated or high temperature air is being handled. elt uards - Sturdy three-sided fabricated steel belt guards provide protection from rotating pulleys and belts. The belt guards meet OS requirements. 7

8 Mounting Options quipment Supports s SS and SR equipment supports are available for roof mounting of all utility fans. quipment supports are available in a number of lengths, widths and heights, and can also be built for a pitched roof. Vibration solators ase mounted neoprene or housed spring isolators are available to lessen mechanical vibration and assure quiet operation. The model SW is available with 1/4-inch of deflection neoprene isolators. ree standing, restrained and housed spring isolators are also available. solators are sized to match the weight of each fan. Mounting Rails solation mounting rails are available with 1/4-in. of deflection, free standing, or restrained spring isolators. The isolators are mounted in an aluminum rail that runs the length of the fan base. solation rails provide easy installation on isolated systems, and are ideal for applications where there is a large overhung load. irect Mount - Type No base required. solators are attached directly to equipment. irect isolation can be used if equipment is unitary and rigid without the use of additional support. irect isolation is not recommended for equipment having large overhung loads (e.g. motors on rr. 9 fans). f there is any doubt whether or not equipment can be supported directly on isolators; use rails, bases or consult the factory. Spring Mount Rubber Mount Rubber Mounts - Type, 1/4 in. & 1/ in. eflection Neoprene mountings consist of a steel top plate and base plate completely embedded in colored (oil-resistant) neoprene for easy identification of capacity. Neoprene mountings are furnished with a tapped hole in the center. This enables the equipment to be bolted securely to the rubber mount. oused Spring Mounts - Type 4, 1 in. eflection oused spring isolators consist of steel springs assembled into a telescoping housing with a top mounted adjusting bolt and an acoustical nonskid base. oused spring isolators include resilient inserts to prevent metal-to-metal contact and provide snubbing for side loads. Springs provide an additional 50% overload capacity and are color coded or identified to indicate load capacity. ree-standing Open Spring Mounts - Type 3, 1 in. eflection ree-standing spring isolators are unhoused laterally stable steel springs. They provide a minimum horizontal stiffness of 0.8 times the rated vertical stiffness and provide an additional 50% overload capacity. These isolators are equipped with a top mounted adjusting bolt and an acoustical nonskid base. Springs are color coded or identified to indicate load capacity. Restrained Spring Mounts - Type 4, 1 in. eflection Restrained spring isolators consist of laterally stable, free-standing springs assembled into a steel housing. These assemblies are designed for vertical and horizontal motion restraint. Restrained spring isolators can be used for blocking during equipment installation and are provided with leveling bolts. Springs provide 50% overload capacity and are color coded or identified to indicate load capacity. Restrained spring mounts are recommended for equipment subject to wind loading or large torquing forces. 8

9 ischarge Position W U W U W TU W T W T W W W W U W U W W UU W U W U W TU W W TU W TU W U W W T TU W T W W T T W T W T W W W T W W T W W W U W U W W UU W U W TU W W TU W TU W U W W T TU W T W W T T W T W T W W T W W T W W W W W W W W W UU W U W W TU W TU W W T TU W T W TU W W T T W T W T W W T W W T W W W W W W W W W W W W TU SW Size 106 W 107T W W T 108 TU W TU /16 (49) 1 15 /16 (49) 1 15 /16 (49) 1 15 /16 (49) 11 /16 (68) 14 1 /8 (359) 91/4 (35) 14 1 /8 91/4 (359) W T(35) 14 1 /8 W W T T (359) 14 1 /8 (359) 17 5 /8 (448) W T /8 191/ (79) (495) W W T T W W T 31/ 11/4 116 W T (89) W (540) T /16 (103) 4 9 /16 10 (116) W 14 W W T W T /16 (40) 1 15 / /16 (198) 103/4 (73) 7 13 /16 103/4 (198) W (73) 91/ W W /16 T103/4 (35) (198) (73) W 91/ T /16 103/4 (35) (198) (73) 113/4 (98) 13 1 / /8 (51) 13 5 /8 (346) 10 1 /8 (57) 10 1 /8 8 5 /8 8 5 /8 (57) W 10 1 /8 8 5 /8 W W (57) W 10 1 /8 (57) 13/4 (34) 8 5 / /8 (76) 1 1 /8 W 11W 15 1 / /8 W (33) (79) (384) (359) (308) 14 5 /15 W W /16 W W 151/ 131/4 (364) W (305) (406) W (394) (337) 3 3 / /16 131/ / / /8 (594) (40) (337) (465) (435) (371) 51/ 171/4 (648) (438) W / /16 W W (786) (535) 14 1 /8 W (49) (359) (49) 1 15 /16 W 08 (49) W W 10 W 1 13 W 15 W W 16 W 18 0 W W /8 (359) 14 1 /8 W (359) 14 1 /8 141/ 0 1 /16 (368) (510) W 173/4 4 7 /16 W W (451) (61) 91/ /16 W (35) (198) 91/4 (35) 91/4 (35) 7 13 /16 (198) 7 13 /16 (198) 103/4 (73) 103/4 (73) 103/4 (73) 1 15 /16 91/ /16 W W W 103/4 (49) (359) (35) (198) (73) 5 /16 W 16 1 / /16 W /8 (59) (410) (71) (9) (314) 11 /16 (68) 17 5 /8 (448) 3 1 /8 191/ (79) (495) W 31/ 11/4 (89) W (540) (103) 4 9 /16 (116) 5 3 /16 (13) 5 13 /16 (40) 5 (17) 6 5 /8 (168) 7 1 /4 (184) 8 (03) W TU 1 15 / / /8 (594) 51/ (648) 8 1 /16 (713) /16 (786) 8 1 /16 (713) 38 1 /8 (968) 41 (1041) 46 3 /8 (1178) 113/4 (98) 13 1 /16 (33) 14 5 /15 (364) /16 (40) 171/4 (438) 19 1 /16 (484) 1 1 /16 (535) 19 1 /16 (484) 5 (635) 7 (686) 303/4 (781) 9 7 /8 (51) 11 (79) 1 (305) 131/4 (337) 141/ (368) 16 (406) 173/4 (451) 16 (406) 1 1 /8 (537) 3 (584) 5 5 /8 (651) ll dimensions in inches (millimeters). W T 13 5 /8 (346) 15 1 /8 (384) 16 9 /16 (406) 18 5 /16 (465) 0 1 /16 (510) 1 /8 (56) 4 7 /16 (61) 1 /8 (56) 9 (737) 3 3 /8 (8) 35 (889) W W T 183/4 (476) 7 / /8 (410) 19 9 /16 (581) W (497) 10 1 /8 W (57) 10 1 /8 (57) 10 1 /8 (57) 10 1 /8 (57) 11 5 /8 (95) 13/4 (34) 14 1 /8 (359) 151/ (394) 17 1 /8 (435) 183/4 (476) 0 5 /8 (54) 7 /8 (581) 0 5 /8 (54) 71/4 (69) 30 1 /4 (768) 3 7 /8 (835) 8 5 /8 8 5 /8 8 5 /8 8 5 / /16 (5) 10 7 /8 (76) 1 1 /8 (308) 131/4 (337) 14 5 /8 (371) 16 1 /8 (410) /16 (449) 19 9 /16 (497) /16 (449) 31/4 (591) 5 13 /16 (656) 8 1 /16 (713) W W 15 1 /8 (384) 111/ (9) 15 1 /8 111/ (384) W (9) 15 1 W W /8 111/ (384) (9) W 15 1 /8 111/ (384) (9) 16 5 /8 (4) 14 5 /8 (371) 181/ 161/4 (470) (413) W 0 3 /8 173/4 W (518) (451) 3 / /8 (568) (498) 41/ (6) 311/ (800) 15 1 /8 (384) 15 1 /8 (384) 15 1 /8 (384) 15 1 /8 (384) 15 1 /8 (384) 16 5 /8 (4) 181/ (470) 0 3 /8 (518) 3 /8 (568) 41/ (6) 8 3 /4 (730) 311/ (800) 8 3 /4 (730) 36 5 /8 (930) 40 (1016) 441/ (1130) 11/ (546) 61/4 (667) 111/ (9) 111/ (9) 111/ (9) 111/ (9) 13 1 /4 (337) 14 5 /8 (371) 161/4 (413) 173/4 (451) 19 5 /8 (498) 11/ (546) 3 3 /4 (603) 61/4 (667) 3 3 /4 (603) 31 3 /8 (797) 35 (889) 38 5 /8 (981) 8 5 /8 8 5 /8 8 5 /8 W W 8 5 / /8 (70) 11 5 /8 (95) 11/ (318) 133/4 (349) 14 7 /8 (378) 173/4 (451) 8 5 /8 8 5 /8 8 5 /8 8 5 /8 9 3 /4 (48) 10 5 /8 (70) 11 5 /8 (95) 11/ (318) 133/4 (349) 14 7 /8 (378) 16 1 /4 (413) 173/4 (451) 16 1 /4 (413) 11/ (546) 5 (635) 71/4 (69) W W 9 W W

10 Typical nstallations SW Series 100 and 00 are designed for supply, exhaust and return air applications. Tests were conducted to assure safe, rugged and reliable fans capable of withstanding severe conditions. ue to the varying airstreams encountered in commercial ventilation, system designers must be aware of national, state and local codes and guidelines governing these installations. eneral lean ir or ume ood (Non rease) reenheck s SW Series 100 and 00 are designed for applications ranging from clean air to contaminated air. Typical installations are shown below. nstallations must include a means for inspecting, cleaning and servicing the exhaust fan. ommercial Kitchen (rease) 3 Wheel iameters reenheck s SW Series 00 are designed to meet restaurant and food service applications. These fans are UL and cul Listed for grease removal and have been tested under elevated temperature conditions. ue to high temperatures and grease-laden airstreams in commercial kitchen ventilation, system designers must be aware of governing codes and guidelines. The National ire Protection ssociation (NP) is the primary source used by many local codes for commercial kitchen ventilation systems. Local code authorities should be consulted before proceeding with any kitchen ventilation project. nstallation must include a means for inspecting, cleaning and servicing the exhaust fan. ans selected for grease removal must include a weatherhood, bolted access door and 1 in. (5 mm) drain connection. or grease applications where the fan is mounted indoor, the welded scroll option must be selected. n outlet guard is strongly recommended when the fan discharge is accessible. When an outlet guard is not ordered with the fan it must be provided by the installer. n upblast discharge is recommended. No dampers are to be used in the system. The fan must discharge a minimum of 40 in. (1016 mm) above the roof line and the exhaust duct must be fully welded to a minimum distance of 18 in. (457 mm) above the roof surface. Upblast ischarge Optional ompanion lange Series 00 SW models are listed for grease removal (UL/cUL 76). ile no. M11745 **40 in. Weatherhood (1016 mm) 3 Wheel iameters *18 in. (457 mm) 10 ** Per NP 96 the fan discharge must be a minumum distance of 40 in. (1016 mm) above the roof surface. uct rom Kitchen ood * Per NP 96 the duct must be all welded construction to a minumum distance of 18 in. (457 mm) above the roof surface.

11 ngineering ata This catalog contains comprehensive air performance data for reenheck s backward inclined utility fans. ir performance is shown in both fan tables and fan curves. Selection The first consideration in any fan selection is the amount of air to be moved and the resistance to this air movement. ir volume requirements are established through specific codes or accepted industry standards. Once the air volume is known, system resistance can be determined by summing up the losses through the system components. uct layout, duct size, coil, filters, dampers, and fan accessories all affect system resistance. SR uide and ata ooks and manufacturer s data on individual system components are common sources of information available to the system designer. n most applications, several fans may meet the required airflow and system resistance conditions. n optimum fan selection requires evaluation of alternative fan types and fan sizes, as they relate to initial cost, operating cost, available space, and allowable sound levels. The relative importance of these facts varies with each system. ackward inclined utility fans turn at twice the speed of forward curved fans. dvantages of backward inclined fans are higher operating efficiencies and a non-overloading horsepower curve, which reaches a maximum in the middle of the normal operation range. The wheel design is stronger, permitting operation at higher static pressures. Larger fans tend to turn slower and generate less noise. These fans generally have lower operating costs, however, this may be offset by higher initial costs when compared to a smaller fan. or a given application, a smaller fan will have a higher speed and a steeper performance curve. The steeper performance curve minimizes airflow changes in the system as system resistance varies. ffects of nstallation on Performance an ratings presented in the performance tables and curves of this catalog are in accordance with M Standard 10 Laboratory Methods of Testing ans for erodynamic Performance Rating. The M test procedure utilizes an open inlet and a straight outlet duct to assure maximum static regain. ny installation with inlet or discharge configurations that deviate from this standard may result in reduced fan performance. Restricted or unstable flow at the fan inlet can cause pre-rotation of incoming air or uneven loading of the fan wheel yielding large system losses and increased sound levels. ree discharge or turbulent flow in the discharge ductwork will also result in system effect losses. The examples below show system layouts and inlet and discharge configurations which can affect fan performance. OO OO POOR 7 o MX. Not reater than 60 o ncluding ngle POOR POOR OO One an ia. POOR OO OO OO POOR POOR Should be at least 1/ ia. mpeller OO OO POOR 11

12 SW elt rive Series (676) 1 (9) (384) (476) 16 (406) (49) (86) 1 4 (565) 1 (305) Wheel iameter = (83) Shaft iameter = 3/4 (19) Outlet rea = 0.76 ft (0.07 m ) ^pproximate Unit Weight = 135 lb. (61 kg) 15 1 (394) (48) (556) 3 1 (597) ll dimensions in inches (millimeters). or additional discharge positions see page 9. ^Weight shown is largest cataloged Open rip Proof motor. SW-106 an M (51) 11 (79) MXMUM P T VN RPM = (RPM/3706) 3 MXMUM RPM = 3000 TP SP (ft/min.) = RPM x.91 MXMUM MOTOR RM SZ = 145T Static Pressure in nches wg RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones 18.9 Performance certified is for installation Type - free inlet, ducted outlet. Power rating (bhp) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The M ertified Ratings Seal applies to air performance ratings only. Static Pressure Pa Static Pressure in. wg /4 P 1/3 P o not select to the left of this system curve 1/ P cfm m 3 /hr 3000 RPM P ensity lb/ft³

13 SW elt rive Series (676) 1 (9) (384) (476) 16 (406) (49) (86) 1 4 (565) 1 (305) 15 1 (394) (48) (556) 3 1 (597) (51) 11 (79) o not select to the left of this system curve Wheel iameter = (83) Shaft iameter = 3/4 (19) Outlet rea = 0.76 ft (0.07 m ) ^pproximate Unit Weight = 135 lb. (61 kg) ll dimensions in inches (millimeters). or additional discharge positions see page 9. ^Weight shown is largest cataloged Open rip Proof motor. MXMUM P T VN RPM = (RPM/3493) 3 MXMUM RPM = 900 TP SP (ft/min.) = RPM x.91 MXMUM MOTOR RM SZ = 145T SW-107 an M Static Pressure in nches wg RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM 85 P 0.50 Sones 3 Performance certified is for installation Type - free inlet, ducted outlet. Power rating (bhp) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The M ertified Ratings Seal applies to air performance ratings only. 13

14 SW elt rive Series (676) 1 (9) (384) (476) 16 (406) (86) 1 4 (565) 1 (305) 15 1 (394) (48) (51) 11 (79) o not select to the left of this system curve (49) (556) 3 1 (597) Wheel iameter = (83) Shaft iameter = 3/4 (19) Outlet rea = 0.76 ft (0.07 m ) ^pproximate Unit Weight = 135 lb. (61 kg) ll dimensions in inches (millimeters). or additional discharge positions see page 9. ^Weight shown is largest cataloged Open rip Proof motor. MXMUM P T VN RPM = (RPM/333) 3 MXMUM RPM = 800 TP SP (ft/min.) = RPM x.91 MXMUM MOTOR RM SZ = 145T SW-108 an M Static Pressure in nches wg RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM 78 P 0.5 Sones 3 Performance certified is for installation Type - free inlet, ducted outlet. Power rating (bhp) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The M ertified Ratings Seal applies to air performance ratings only. 14

15 SW elt rive Series (676) 1 (9) (384) (476) (406) (49) (86) 1 4 (565) 1 (305) 15 1 (394) (48) (556) 3 1 (597) (51) 11 (79) o not select to the left of this system curve Wheel iameter = (83) Shaft iameter = 3/4 (19) Outlet rea = 0.76 ft (0.07 m ) ^pproximate Unit Weight = 135 lb. (61 kg) ll dimensions in inches (millimeters). or additional discharge positions see page 9. ^Weight shown is largest cataloged Open rip Proof motor. MXMUM P T VN RPM = (RPM/665) 3 MXMUM RPM = 665 TP SP (ft/min.) = RPM x.91 MXMUM MOTOR RM SZ = 145T an M Static Pressure in nches wg RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM SW P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones 7 7 Performance certified is for installation Type - free inlet, ducted outlet. Power rating (bhp) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The M ertified Ratings Seal applies to air performance ratings only. 15

16 SW elt rive Series (794) (371) (4) (594) (70) (448) (479) (36) (69) 13 (330) Wheel iameter = (333) Shaft iameter = 3/4 (19) Outlet rea = 1.03 ft (0.10 m ) ^pproximate Unit Weight = 175 lb. (79 kg) (45) (70) 1 (57) (638) ll dimension in inches (millimeters). or additional discharge positions see page 9. ^Weight shown is largest cataloged Open rip Proof motor. (51) 14 (356) o not select to the left of this system curve MXMUM P T VN RPM = (RPM/084) 3 MXMUM RPM = 385 TP SP (ft/min.) = RPM x 3.53 MXMUM MOTOR RM SZ = 184T 16 an M Static Pressure in nches wg RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM SW P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones Performance certified is for installation Type - free inlet, ducted outlet. Power rating (bhp) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The M ertified Ratings Seal applies to air performance ratings only.

17 SW elt rive Series (883) (413) 18 1 (470) (654) 0 (508) (95) (537) (400) 7 1 (699) 15 (381) Wheel iameter = (370) Shaft iameter = 3/4 (19) Outlet rea = 1.5 ft (0.11 m ) ^pproximate Unit Weight = 5 lb. (10 kg) 18 1 (470) (95) (613) (718) ll dimensions in inches (millimeters). or additional discharge positions see page 9. ^Weight shown is largest cataloged Open rip Proof motor. an M (51) (403) o not select to the left of this system curve MXMUM P T VN RPM = (RPM/1737) 3 MXMUM RPM = 187 TP SP (ft/min.) = RPM x 3.93 MXMUM MOTOR RM SZ = 184T Static Pressure in nches wg RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM SW P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones Performance certified is for installation Type - free inlet, ducted outlet. Power rating (bhp) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The M ertified Ratings Seal applies to air performance ratings only. 17

18 SW elt rive Series (968) (451) (518) 8 (711) 1 1 (318) 17 1 (445) 30 (76) 19 1 (495) (34) (51) 17 1 (445) o not select to the left of this system curve (543) 7 8 (581) 16 (406) (718) (77) Wheel iameter = (45) Shaft iameter = 1 (5) Outlet rea = 1.5 ft (0.14 m ) ^pproximate Unit Weight = 41 lb. (109 kg) ll dimensions in inches (millimeters). or additional discharge positions see page 9. ^Weight shown is largest cataloged Open rip Proof motor. MXMUM P T VN RPM = (RPM/1403) 3 MXMUM RPM = 03 TP SP (ft/min.) = RPM x 4.3 MXMUM MOTOR RM SZ = 184T SW-116 an M Static Pressure in nches wg RPM 750 P 0.15 Sones 5.8 RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones 3 3 Performance certified is for installation Type - free inlet, ducted outlet. Power rating (bhp) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The M ertified Ratings Seal applies to air performance ratings only. 18

19 SW elt rive Series (1067) (498) 3 8 (568) (784) (350) (594) 5 (635) (49) (845) (454) (559) (359) (817) 34 (864) (51) (489) o not select to the left of this system curve Wheel iameter = 18 1 (470) Shaft iameter = 1 (5) Outlet rea = 1.87 ft (0.17 m ) ^pproximate Unit Weight = 31 lb. (14 kg) ll dimensions in inches (millimeters). or additional discharge positions see page 9. ^Weight shown is largest cataloged Open rip Proof motor. SW-118 an M MXMUM P T VN RPM = (RPM/1150) 3 MXMUM RPM = 1660 TP SP (ft/min.) = RPM x 4.78 MXMUM MOTOR RM SZ = 13T Static Pressure in nches wg RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones Performance certified is for installation Type - free inlet, ducted outlet. Power rating (bhp) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The M ertified Ratings Seal applies to air performance ratings only. 19

20 SW-10 - elt rive Series 100 (546) 46 (1168) 4 1 (6) (854) (378) (651) (695) (537) (918) (49) (603) 35 (889) 37 (940) (391) (51) (537) o not select to the left of this system curve Wheel iameter = (543) Shaft iameter = 1 (5) Outlet rea =.3 ft (0.1 m ) ^pproximate Unit Weight = 374 lb. (170 kg) ll dimensions in inches (millimeters). or additional discharge positions see page 9. ^Weight shown is largest cataloged Open rip Proof motor. MXMUM P T VN RPM = (RPM/943) 3 MXMUM RPM = 1357 TP SP (ft/min.) = RPM x 5.3 MXMUM MOTOR RM SZ = 15T 0 SW-10 an M RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones Performance certified is for installation Type - free inlet, ducted outlet. Power rating (bhp) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The M ertified Ratings Seal applies to air performance ratings only.

21 SW-14 - elt rive Series (1467) (667) 3 (800) (103) (451) (791) (854) 6 (661) (116) (50) 5 (635) 19 (483) 36 (914) 4 (1054) 1 (64) (657) o not select to the left of this system curve Wheel iameter = 4 1 (6) Shaft iameter = 1 (5) Outlet rea = 3.40 ft (0.3 m ) ^pproximate Unit Weight = 546 lb. (48 kg) ll dimensions in inches (millimeters). or additional discharge positions see page 9. ^Weight shown is largest cataloged Open rip Proof motor. SW-14 an M MXMUM P T VN RPM = (RPM/713) 3 MXMUM RPM = 15 TP SP (ft/min.) = RPM x 6.41 MXMUM MOTOR RM SZ = 56T Static Pressure in nches wg RPM 413 P 0.19 Sones 4.9 RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones Performance certified is for installation Type - free inlet, ducted outlet. Power rating (bhp) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The M ertified Ratings Seal applies to air performance ratings only. 1

22 SW-06 - elt rive Series (676) 1 (9) (384) (476) (406) (49) (86) 1 4 (565) 1 (305) 15 1 (394) (518) (559) (10) (51) 11 (79) o not select to the left of this system curve Wheel iameter = (83) Shaft iameter = 3/4 (19) Outlet rea = 0.63 ft (0.06 m ) ^pproximate Unit Weight = 140 lb. (64 kg) ll dimensions in inches (millimeters). or additional discharge positions see page 9. ^Weight shown is largest cataloged Open rip Proof motor. SW-06 an M MXMUM P T VN RPM = (RPM/369) 3 MXMUM RPM = 3370 TP SP (ft/min.) = RPM x.91 MXMUM MOTOR RM SZ = 145T Static Pressure in nches wg RPM 101 P 0.03 Sones 6.4 RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones 1 Performance certified is for installation Type - free inlet, ducted outlet. Power rating (bhp) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The M ertified Ratings Seal applies to air performance ratings only.

23 SW-07 - elt rive Series (676) 1 (9) (384) (476) (86) 1 4 (565) 15 1 (394) (10) (51) 11 (79) o not select to the left of this system curve 16 (406) (49) 1 (305) (518) (559) Wheel iameter = (83) Shaft iameter = 3/4 (19) Outlet rea = 0.63 ft (0.06 m ) ^pproximate Unit Weight = 140 lb. (64 kg) ll dimensions in inches (millimeters). or additional discharge positions see page 9. ^Weight shown is largest cataloged Open rip Proof motor. SW-07 an M MXMUM P T VN RPM = (RPM/3099) 3 MXMUM RPM = 3370 TP SP (ft/min.) = RPM x.91 MXMUM MOTOR RM SZ = 145T Static Pressure in nches wg RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones 30 3 Performance certified is for installation Type - free inlet, ducted outlet. Power rating (bhp) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The M ertified Ratings Seal applies to air performance ratings only. 3

24 SW-08 - elt rive Series (676) 1 (9) (384) Wheel iameter = (83) Shaft iameter = 3/4 (19) Outlet rea = 0.63 ft (0.06 m ) ^pproximate Unit Weight = 140 lb. (64 kg) ll dimensions in inches (millimeters). or additional discharge positions see page 9. ^Weight shown is largest cataloged Open rip Proof motor (476) 16 (406) (49) an M (86) 1 4 (565) 1 (305) 15 1 (394) (10) (518) (559) (51) 11 (79) MXMUM P T VN RPM = (RPM/34) 3 MXMUM RPM = 3370 TP SP (ft/min.) = RPM x.91 MXMUM MOTOR RM SZ = 145T Static Pressure in nches wg RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM SW P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones 6 5 Performance certified is for installation Type - free inlet, ducted outlet. Power rating (bhp) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The M ertified Ratings Seal applies to air performance ratings only. Static Pressure Pa Static Pressure in. wg /4 P 1/3 P 670 1/ P 3/4 P P o not select to the left of this system curve cfm m 3 /hr 1 1/ P 3370 RPM P ensity lb/ft³

25 SW-10 - elt rive Series (676) 1 (9) (384) (476) 16 (406) (49) (86) 1 4 (565) 1 (305) 15 1 (394) (518) (559) (10) (51) 11 (79) o not select to the left of this system curve Wheel iameter = (83) Shaft iameter = 3/4 (19) Outlet rea = 0.63 ft (0.06 m ) ^pproximate Unit Weight = 140 lb. (64 kg) ll dimensions in inches (millimeters). or additional discharge positions see page 9. ^Weight shown is largest cataloged Open rip Proof motor. an M MXMUM P T VN RPM = (RPM/649) 3 MXMUM RPM = 3370 TP SP (ft/min.) = RPM x.91 MXMUM MOTOR RM SZ = 145T Static Pressure in nches wg RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM SW P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones Performance certified is for installation Type - free inlet, ducted outlet. Power rating (bhp) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The M ertified Ratings Seal applies to air performance ratings only. 5

26 SW-1 - elt rive Series (71) (337) (384) (543) (48) 16 (406) (49) 13 (330) 1 4 (565) 1 (305) 15 1 (394) (44) (543) 9 10 (58) (51) 13 (330) o not select to the left of this system curve 6 Wheel iameter = (311) Shaft iameter = 1 (5) Outlet rea = 0.85 ft (0.08 m ) ^pproximate Unit Weight = 170 lb. (77 kg) ll dimensions in inches (millimeters). or additional discharge positions see page 9. ^Weight shown is largest cataloged Open rip Proof motor. an M MXMUM P T VN RPM = (RPM/37) 3 MXMUM RPM = 36 TP SP (ft/min.) = RPM x 3.1 MXMUM MOTOR RM SZ = 145T Static Pressure in nches wg RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM SW P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones Performance certified is for installation Type - free inlet, ducted outlet. Power rating (bhp) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The M ertified Ratings Seal applies to air performance ratings only.

27 SW-13 - elt rive Series (794) (371) (4) (594) (70) (448) (479) (36) (69) 13 (330) (45) (70) 1 (57) (638) (51) 14 (356) o not select to the left of this system curve Wheel iameter = 13 1 (343) Shaft iameter = 1 (5) Outlet rea = 1.03 ft (0.10 m ) ^pproximate Unit Weight = 183 lb. (83 kg) ll dimensions in inches (millimeters). or additional discharge positions see page 9. ^Weight shown is largest cataloged Open rip Proof motor. an M MXMUM P T VN RPM = (RPM/00) 3 MXMUM RPM = 90 TP SP (ft/min.) = RPM x 3.53 MXMUM MOTOR RM SZ = 184T Static Pressure in nches wg RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM SW P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones Performance certified is for installation Type - free inlet, ducted outlet. Power rating (bhp) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The M ertified Ratings Seal applies to air performance ratings only. 7

28 SW-15 - elt rive Series (883) (413) 18 1 (470) (654) 0 (508) (96) (537) (400) 7 1 (699) 15 (381) 18 1 (470) (95) (613) (714) (51) (403) o not select to the left of this system curve Wheel iameter = 15 (381) Shaft iameter = 1 (5) Outlet rea = 1.5 ft (0.1 m ) ^pproximate Unit Weight = 31 lb. (105 kg) ll dimensions in inches (millimeters). or additional discharge positions see page 9. ^Weight shown is largest cataloged Open rip Proof motor. MXMUM P T VN RPM = (RPM/1679) 3 MXMUM RPM = 604 TP SP (ft/min.) = RPM x 3.93 MXMUM MOTOR RM SZ = 184T SW-15 an M Static Pressure in nches wg RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P.7.93 Sones Performance certified is for installation Type - free inlet, ducted outlet. Power rating (bhp) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The M ertified Ratings Seal applies to air performance ratings only. 8

29 SW-16 - elt rive Series (968) (451) (518) 8 (711) 1 1 (318) (543) 7 8 (581) 17 1 (445) 30 (76) 16 (406) 19 1 (495) (34) (718) (77) (51) 17 1 (445) o not select to the left of this system curve Wheel iameter = 16 1 (419) Shaft iameter = (3) Outlet rea = 1.5 ft (0.14 m ) ^pproximate Unit Weight = 51 lb. (114 kg) ll dimensions in inches (millimeters). or additional discharge positions see page 9. ^Weight shown is largest cataloged Open rip Proof motor. MXMUM P T VN RPM = (RPM/1414) 3 MXMUM RPM = 378 TP SP (ft/min.) = RPM x 4.3 MXMUM MOTOR RM SZ = 184T SW-16 an M Static Pressure in nches wg RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones Performance certified is for installation Type - free inlet, ducted outlet. Power rating (bhp) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The M ertified Ratings Seal applies to air performance ratings only. 9

30 SW-18 - elt rive Series 00 4 (1067) (498) 3 8 (568) (784) (349) (594) 5 (635) (49) (845) (454) (559) (819) 34 (864) (359) (51) (489) o not select to the left of this system curve Wheel iameter = (464) Shaft iameter = (3) Outlet rea = 1.87 ft (0.17 m ) ^pproximate Unit Weight = 34 lb. (147 kg) ll dimensions in inches (millimeters). or additional discharge positions see page 9. ^Weight shown is largest cataloged Open rip Proof motor. MXMUM P T VN RPM = (RPM/1196) 3 MXMUM RPM = 147 TP SP (ft/min.) = RPM x 4.78 MXMUM MOTOR RM SZ = 13T SW-18 an M Static Pressure in nches wg RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones Performance certified is for installation Type - free inlet, ducted outlet. Power rating (bhp) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The M ertified Ratings Seal applies to air performance ratings only. 30

31 SW-0 - elt rive Series (1168) (546) 4 1 (6) (854) (378) (651) (695) (537) (918) (49) (603) 35 (889) 37 (940) (390) (51) (537) o not select to the left of this system curve Wheel iameter = 0 (508) Shaft iameter = (3) Outlet rea =.3 ft (0.1 m ) ^pproximate Unit Weight = 389 lb. (176 kg) ll dimensions in inches (millimeters). or additional discharge positions see page 9. ^Weight shown is largest cataloged Open rip Proof motor. SW-0 an M MXMUM P T VN RPM = (RPM/107) 3 MXMUM RPM = 1961 TP SP (ft/min.) = RPM x 5.3 MXMUM MOTOR RM SZ = 15T Static Pressure in nches wg RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones Performance certified is for installation Type - free inlet, ducted outlet. Power rating (bhp) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The M ertified Ratings Seal applies to air performance ratings only. 31

32 SW- - elt rive Series (1334) (603) (730) (937) (413) (718) 30 1 (775) 3 1 (597) 4 (1054) 0 (508) 4 (610) 17 (43) (867) (1006) 1 (64) 3 (584) o not select to the left of this system curve Wheel iameter = 1 4 (565) Shaft iameter = (3) Outlet rea =.74 ft (0.5 m ) ^pproximate Unit Weight = 450 lb. (04 kg) ll dimensions in inches (millimeters). or additional discharge positions see page 9. ^Weight shown is largest cataloged Open rip Proof motor. MXMUM P T VN RPM = (RPM/897) 3 MXMUM RPM = 1798 TP SP (ft/min.) = RPM x 5.8 MXMUM MOTOR RM SZ = 15T SW- an M Static Pressure in nches wg RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones Performance certified is for installation Type - free inlet, ducted outlet. Power rating (bhp) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The M ertified Ratings Seal applies to air performance ratings only. 3

33 SW-4 - elt rive Series (1467) (667) 3 (800) (103) (451) (803) (854) 6 (660) (116) (50) Wheel iameter = 4 1 (6) Shaft iameter = Outlet rea = 3.40 ft (0.3 m ) ^pproximate Unit Weight = 568 lb. (58 kg) 5 (635) 36 (914) 19 (483) 4 (1054) ll dimensions in inches (millimeters). or additional discharge positions see page 9. ^Weight shown is largest cataloged Open rip Proof motor. SW-4 an M (64) (657) o not select to the left of this system curve MXMUM P T VN RPM = (RPM/749) 3 MXMUM RPM = 1588 TP SP (ft/min.) = RPM x 6.41 MXMUM MOTOR RM SZ = 56T Static Pressure in nches wg RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones Performance certified is for installation Type - free inlet, ducted outlet. Power rating (bhp) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The M ertified Ratings Seal applies to air performance ratings only. 33

34 SW-7 - elt rive Series (1553) (714) 33 (838) (1137) (514) (89) (956) (71) (79) (148) 1 4 (565) Wheel iameter = (683) Shaft iameter = Outlet rea = 4.10 ft (0.38 m ) ^pproximate Unit Weight = 715 lb. (34 kg) 7 (686) 1 (533) 40 1 (109) 46 (1168) ll dimensions in inches (millimeters). or additional discharge positions see page 9. ^Weight shown is largest cataloged Open rip Proof motor. SW-7 an M (64) 8 1 (74) o not select to the left of this system curve MXMUM P T VN RPM = (RPM/637) 3 MXMUM RPM = 1464 TP SP (ft/min.) = RPM x 7.03 MXMUM MOTOR RM SZ = 84T Static Pressure in nches wg RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones Performance certified is for installation Type - free inlet, ducted outlet. Power rating (bhp) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The M ertified Ratings Seal applies to air performance ratings only.

35 SW-30 - elt rive Series (177) (797) (930) (138) (546) (975) (1045) 3 (813) 1 (64) (1365) (559) Wheel iameter = (75) Shaft iameter = (44) Outlet rea = 5.03 ft (0.47 m ) ^pproximate Unit Weight = 810 lb. (367 kg) 7 (686) (594) (1086) (16) ll dimensions in inches (millimeters). or additional discharge positions see page 9. ^Weight shown is largest cataloged Open rip Proof motor. SW-30 an M (806) Performance certified is for installation Type - free inlet, ducted outlet. Power rating (bhp) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The M ertified Ratings Seal applies to air performance ratings only. 1 (64) o not select to the left of this system curve MXMUM P T VN RPM = (RPM/534) 3 MXMUM RPM = 1306 TP SP (ft/min.) = RPM x 7.75 MXMUM MOTOR RM SZ = 84T Static Pressure in nches wg RPM 418 P 0.46 Sones 7.1 RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones

36 SW-33 - elt rive Series (889) 75 (1905) 40 (1016) 55 1 (1410) 5 (635) (1057) (111) (886) 3 1 (89) (150) 3 1 (597) Wheel iameter = 33 (838) Shaft iameter = (44) Outlet rea = 6.1 ft (0.57 m ) ^pproximate Unit Weight = 980 lb. (445 kg) 9 (737) (641) 46 (1168) 5 (131) ll dimensions in inches (millimeters). or additional discharge positions see page 9. ^Weight shown is largest cataloged Open rip Proof motor. an M 1 (64) (886) o not select to the left of this system curve MXMUM P T VN RPM = (RPM/45) 3 MXMUM RPM STL/LUMNUM = 1156/975 TP SP (ft/min.) = RPM x 8.64 MXMUM MOTOR RM SZ = 86T Static Pressure in nches wg RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM SW P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones Performance certified is for installation Type - free inlet, ducted outlet. Power rating (bhp) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The M ertified Ratings Seal applies to air performance ratings only.

37 SW-36 - elt rive Series (111) (981) 44 1 (1130) (1546) (69) (984) 3 1 (89) (1667) 30 (76) (718) 1 (64) 38 1 (978) o not select to the left of this system curve (1165) (135) (603) Wheel iameter = (91) Shaft iameter = (51) Outlet rea = 7.5 ft (0.70 m ) ^pproximate Unit Weight = 1170 lb. (531 kg) 46 (1168) (1407) ll dimensions in inches (millimeters). or additional discharge positions see page 9. ^Weight shown is largest cataloged Open rip Proof motor. MXMUM P T VN RPM = (RPM/387) 3 MXMUM RPM STL/LUMNUM = 1073/960 TP SP (ft/min.) = RPM x 9.46 MXMUM MOTOR RM SZ = 86T an M Static Pressure in nches wg RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM SW P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones RPM P Sones Performance certified is for installation Type - free inlet, ducted outlet. Power rating (bhp) does not include transmission losses. Performance ratings do not include the effects of appurtenances (accessories). The M ertified Ratings Seal applies to air performance ratings only. 37

38 Page mergency eader Smoke ontrol Products Mounting Performance Max Ps in. wg Roof S-U ,000 cfm Roof RUMO 3,00-61,700 cfm 1 Roof TU L/ 4,000-74,000 cfm 1 Roof or nline Roof or nline nline or Roof nline or Roof nline or Roof nline or Roof nline or Roof nline or Roof M Sound & ir Sound & ir Sound & ir SW 70-7,000 cfm 5 ir SW 50-00,000 cfm 14 Sound & ir X ,000 cfm 5 ir Q,000-95,000 cfm 8.5 Q 1,000-96,000 cfm 9.5 Sound & ir Sound & ir T 1,500-95, ir T-S 4,800-74,000 cfm 4 Sound & ir ertification UL/cUL mergency Smoke or 705 lectrical mergency Smoke, 705 lectrical or 793 Snow Load mergency Smoke, 705 lectrical or 793 Snow Load mergency Smoke or 705 lectrical mergency Smoke or 705 lectrical mergency Smoke, 705 lectrical or 793 Snow Load mergency Smoke, 705 lectrical or 793 Snow Load mergency Smoke or 705 lectrical mergency Smoke, 705 lectrical or 793 Snow Load mergency Smoke, 705 lectrical or 793 Snow Load Rating 500º / 4 hrs. 1,000º / 15 min. 500º / 4 hrs. 1,000º / 15 min. 500º / 4 hrs. 1,000º / 15 min. 500º / 4 hrs. 1,000º / 15 min. 500º / 4 hrs. 1,000º / 15 min. 30º / 5 hrs. 48º / hrs. 500º / 4 hrs. 57º / 30 min. 57º/ 1 hr. 500º / 4 hrs. 57 / 1 hr. 30º / 5 hrs. 39 / hrs. 48º / 1 hr 500º / 5 hrs. 57º / 1 hr. 500º / 4 hrs. 75 / hrs. 1,000º / 15 min. 750º / 4 hrs. 1,000º / 15 min. Leakage lass N N N N N N N N N N Program Standard 5 ay 10 ay 5 ay 10 ay Standard 10 ay 10 ay 10 ay 10 ay T ,000 cfm 3.5 ir 705 lectrical 300º / 5 hrs. N 10 ay Smoke SM,000-3,000 fpm 4 ir 555S 350º,, Next ay Smoke S-401 3,000 fpm S 50º Standard ire Smoke S,000-3,000 fpm 4 ir 555 & 555S 350º / - 3 hrs.,, Next ay orridor or Out of Wall S & OS,000-3,000 fpm 4 ir 555 & 555S 350º / - 3 hrs.,, Next ay Multi-lade ire,000 fpm 4 ir hrs. N Next ay odes & ertifications UL 555 This standard governs fire dampers which are intended for use where air ducts penetrate or terminate at openings in walls or partitions, in air transfer openings in partitions, and where air ducts extend through floors as specified in the Standard for nstallation of ir-onditioning and Ventilating Systems, NP 90. n a fire emergency the fire damper is designed to close and prevent the spread of fire from one side of the wall or partition to the other. Testing includes cycling, salt spray, dust loading, dynamic closure, fire endurance, and hose stream. UL 555S This standard governs smoke dampers which are intended to prevent the spread of smoke when V systems shut down during a fire emergency and those which control the movement of smoke within a building when the V system functions in a smoke control mode. Leakage rated dampers are intended for installation in accordance with NP 90. Testing includes salt spray, dust loading, cycling, temperature degradation, operation while under heated airflow, and elevated temperature leakage. UL 705 ntended to assure the buyer of the safety of electrical components and connections within power ventilators and duct fans. Limited to fans connected to permanently installed wiring that meet NP 70 and the National lectric ode. Tests under this standard relate to extremes of current, temperature, fuses, motor windings, bearing temperatures, and water that a fan could be subject to. UL - Power Ventilators for Smoke ontrol Systems Ventilators or duct fans have been 38

39 Page Restaurant eader xhaust ans Mounting Performance Max Ps in. wg M ertification UL/cUL Rating Program Wall W & W 70-1,500 cfm.5 Sound & ir 705 lectrical 76 rease Removal 400 UL/cUL 76 Next ay Roof U & U 70-30,000 cfm 5 Sound & ir 705 lectrical 76 rease Removal 400 UL/cUL 76 Next ay Roof Sound -U & -U 70-14,700 cfm 5 & ir 705 lectrical 76 rease Removal 400 UL/cUL 76 Next ay Roof US 330-6, Sound & ir 705 lectrical 76 rease Removal 400 UL/cUL ay Roof or nline SW 70-7,000 cfm 5 ir mergency Smoke, 705 lectrical or 76 rease Removal 400 UL/cUL 76 5 ay Roof or nline SW 50-00,000 cfm 14 Sound & ir mergency Smoke, 705 lectrical or 76 rease Removal 400 UL/cUL ay nline Q,000-95,000 cfm 8.5 Sound & ir mergency Smoke, 705 lectrical or 76 rease Removal 793 Snow Load 400 UL/cUL ay nline T 360-4, Sound & ir 705 lectrical 76 rease Removal 300 UL ay Roof Vektor- 70-4,000 cfm 3.5 Sound & ir 705 lectrical 76 rease Removal 00 UL ay investigated with respect to their operation during exposure to elevated temperatures. nstalled as part of a smoke control system and in accordance NP 9 and 9. Requirements also include UL 705 and if applicable UL 793. Meets the R and S Standard ire Prevention ode requirements. UL 76 UL 76 is for exhausting grease in the airstream as found in restaurant or kitchen applications. asic testing is the same as for UL 705 and additional testing includes operating the fan in a high temperature airstream without warpage, deterioration or damage that would cause the fan to operate unsafely plus grease flare-up tests. reenheck products with UL 76 include most centrifugal roof upblast and centrifugal sidewall fans, utility fans and housed centrifugal fans. UL 793 Specific code applying to power ventilators that have integral dampers. ncludes the ability for automatic damper operation that does not depend on electric power that may be interrupted during fire. ampers blades must be capable of overcoming a 10 lb. / ft of wind, snow, or dust load. M The M certified rating program seal assures you that a product line has been tested to the appropriate M standards in accordance with a legal license agreement and that the manufacturer s catalogued certified ratings have been submitted to the M staff for approval prior to publication. 39

40 Specifications Supply, exhaust and return air fans shall be of the belt driven utility fan type in M rrangement 10 with a single width, single inlet housing, in W or W rotation as specified. The housing shall be constructed of heavy gauge steel with air tight locked formed seams; galvanized steel on Series 100, painted steel on Series 00 or aluminum optional. The housing shall be field rotatable to any of the eight standard discharge positions. ousing and bearing supports shall be constructed of welded steel members to prevent vibration and to rigidly support the shaft and bearings. The fan wheel shall be of the nonoverloading backward inclined, centrifugal fan type and constructed of heavy gauge steel for the Series 00 (except sizes 06 to 10 have aluminum) and aluminum for the Series 100. Wheels shall be statically and dynamically balanced. The wheel cone and fan inlet cone shall be carefully matched for maximum performance and operating efficiency. Motors shall be heavy duty, ball bearing type matched to the fan load and furnished at the specified voltage, phase and enclosure. The fan shaft shall be ground and polished solid steel mounted in heavy duty, permanently sealed, pillow block ball bearings. earings shall be selected for a minimum L 10 life in excess of 100,000 hours (L 50 average life of 500,000 hours) at maximum cataloged operating speed. rives shall be sized for a minimum of 150% of driven horsepower. Pulleys shall be of the fully machined cast iron type, keyed and securely attached to the wheel and motor shafts. The motor pulley shall be adjustable for final system balancing. ll fans shall bear the M ertified Ratings Seal for air performance. Utility fans shall be model SW (with backward inclined wheels) as manufactured by reenheck an orporation in Schofield, Wisconsin. uilding Value in ir reenheck delivers value to mechanical engineers by helping them solve virtually any air quality challenges their clients face with a comprehensive selection of top quality, innovative airrelated equipment. We offer extra value to contractors by providing easy-to-install, competitively priced, reliable products that arrive on time. nd building owners and occupants value the energy efficiency, low maintenance and quiet dependable operation they experience long after the construction project ends. Our Warranty reenheck warrants this equipment to be free from defects in material and workmanship for a period of one year from the purchase date. ny units or parts which prove defective during the warranty period will be replaced at our option when returned to our factory, transportation prepaid. Motors are warranted by the motor manufacturer for a period of one year. Should motors furnished by reenheck prove defective during this period, they should be returned to the nearest authorized motor service station. reenheck will not be responsible for any removal or installation costs. s a result of our commitment to continuous improvement, reenheck reserves the right to change specifications without notice. Prepared to Support reen uilding fforts P.O. ox 410 Schofield, W Phone (715) greenheck.com opyright 008 reenheck an orp. atalog SW Rev. 9 une 008