... OPERATOR AND PARTS MANUAL

Transcription

1 ... OPERATOR AND PARTS MANUAL Stationary Round Bale Unroller 60" & 72" 13C R1 April 2016

2 2 13C R1 - Stationary Unroller 60" & 72" - April 2016

3 TABLE OF CONTENTS SERIAL NUMBER LOCATION...4 SECTION 1 - INTRODUCTION...5 SECTION 2 - SAFETY GENERAL SAFETY OPERATING SAFETY MAINTENANCE SAFETY ELECTRICAL SAFETY INSTALLATION SAFETY SAFETY DECALS SIGN-OFF FORM...8 SECTION 3 - SAFETY DECAL LOCATION...10 SECTION 4 - MAINTENANCE CHAIN ADJUSMENT LUBRICANT AND OIL CHANGE LUBRICANT SELECTION...12 LUBRICANT TABLE...12 PARTS LIST Drive Unit...14 Base...16 Hopper Feet section Feet section...22 Legs Kit - 5 Feet Section...24 Legs Kit - 10 Feet Section...26 Bale Blocker...28 Chain and paddles...30 Warranty C R1 - Stationary Unroller 60" & 72" - April

4 SERIAL NUMBER LOCATION Always state the serial number of your Valmetal equipment when ordering parts or requesting service or other information. The serial number plate is located where indicated. Please mark the number in the space provided for easy reference. TÉL.: (819) MOD. SORTIE 170, ROUTE 20 ST-GERMAIN, DRUMMONDVILLE QUÉBEC, CANADA, J0C 1K0 SER. FABRIQUÉ AU CANADA MADE IN CANADA MODEL : SERIAL NUMBER : 4 13C R1 - Stationary Unroller 60" & 72" - April 2016

5 SECTION 1 - INTRODUCTION Congratulations on your choice of a ValMetal Stationary Round Bale Unroller to complement your farming operation. This equipment has been designed and manufactured to meet the needs of a discriminating buyer. Safe, efficient and trouble free operation of your new equipment requires that you and anyone else who will be operating or maintaining the machine, read and understand the Safety, Operation and Maintenance informations contained in this Operator's Manual. Keep this manual handy for frequent reference and to pass on to new operators or owners. Call your ValMetal Dealer or Distributor if you need assistance or information. 13C R1 - Stationary Unroller 60" & 72" - April

6 SECTION 2 - SAFETY SAFETY ALERT SYMBOL The Safety Alert symbol identifies important safety messages on this Valmetal equipment and in this manual. When you see this Safety Alert symbol, be alert to the possibility of personal injury or death. Follow the instructions in the safety message. This Safety Alert symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! 3 big reasons why SAFETY is so important to you? Accidents Disable and Kill, Accidents Cost, Accidents Can be avoided. Note : The use of the signal words DANGER, WARNING and CAUTION with the safety messages. The appropriate signal word for each message has been selected using the following guide-lines: DANGER CAUTION An immediate and specific hazard which WILL result in severe personal injury or death if the proper precautions are not taken. A specific hazard or unsafe practice which COULD result in severe personal injury or death if proper precautions are not taken. WARNING Unsafe practices which COULD result in personal injury if proper practices are not taken, or as a reminder of good safety practices. 6 13C R1 - Stationary Unroller 60" & 72" - April 2016

7 IMPORTANT YOU are responsible for the SAFE operation and maintenance of your equipment. YOU must ensure that you and anyone else who is going to operate, maintain or work around the machine be familiar with the operating and maintenance procedures and related SAFETY information contained in this manual. Remember, YOU are the key to safety. Good safety practices not only protect you but also the people around you. Make these practices a working part of your safety program. Be certain that EVERYONE operating this equipment is familiar with the recommended operating and maintenance procedures and follows all the safety precautions. Most accidents can be prevented. Do not risk injury or death by ignoring good safety practices. Owners must give operating instructions to operators or employees before allowing them to operate the machine, and at least annually thereafter per OSHA regulation The most important safety device on this equipment is a SAFE operator. It is the operator's responsibility to read and understand ALL Safety and Operating instructions in the manual and to follow these. All accidents can be avoided. A person who has not read and understood all operating and safety instructions is not qualified to operate the machine. An untrained operator exposes himself and bystanders to possible serious injury or death. Do not modify the equipment in any way. Unauthorized modification may impair the function and/or safety and could affect the Iife of the machine. Think SAFETY! Work SAFELY! 2.1 GENERAL SAFETY 1. Read and understand the Operator s Manual and all safety signs before operating, maintaining or adjusting this equipment. 2. Have a first-aid kit available for use should the need arise and know how to use it. 3. Have a fire extinguisher available for use should the need arise and know how to use it. 4. Wear appropriate protective gear. This list includes but is not limited to: A hard hat Protective shoes with slip resistant soles Protective glasses or goggles Heavy gloves Wet weather gear Hearing protection Respirator or filter mask 5. Install and secure all guards before starting. 6. Have only a certified electrician connect power to the unit. 7. Know the location and function of the master electrical shutdown should the need arise. 8. Turn OFF motor, lock out power at master power panel and wait for all moving parts to stop before servicing, maintaining, repairing, adjusting or unplugging. 9. Clear the area of people, especially small children, before starting the unit. 10. Do not permit children to play on or around the equipment, even when not in use. 11. Review all safety related items annually with all personnel who will be operating or maintaining this machine. 2.2 OPERATING SAFETY The moving parts could cause death or severe injury to persons coming in contact with these parts. To help avoid serious accidents, the following guidelines should always be followed. 1. Read and understand the Operator s Manual and all safety signs before operating, servicing, adjusting, repairing, unplugging or filling. 2. Be sure all safety shields are in good condition and properly installed before operating, including driveline shields. 3. Do not allow inexperienced or unqualified persons to operate the machine. Keep bystanders away from equipment while it is in operation. Keep children a safe distance away. Operators of this machine must use common sense at all times. 4. Do not wear loose or floppy clothing while operating this equipment. Loose clothing may become entangled in moving parts or moving machinery and cause severe injury or death. 13C R1 - Stationary Unroller 60" & 72" - April

8 5. Know the location and function of the master electrical shutdown should the need arise 6. Should a problem occur during operation, turn OFF motor, lock out power at master power panel and wait for all moving parts to stop before servicing, adjusting or repairing. 7. Review safety instructions with all operators annually. 2.3 MAINTENANCE SAFETY 1. Follow ALL the operating, maintenance and safety informations in the manual. 2. Follow good Shop Practices: Keep service area clean and dry. Be sure electrical outlets and tools are properly grounded. Use adequate light for the job at hand. 3. Always turn OFF motor, lock out power at master power panel and wait for all moving parts to stop before servicing, adjusting, repairing or unplugging. 4. Keep hands, feet, hair and clothing away from moving and/or rotating parts. 5. Never wear ill-fitting, baggy or frayed clothing when working around or on any of the drive system components. 2.4 ELECTRICAL SAFETY 1. Have a qualified electrician to connect power to the machine. 2. Keep electrical wires and connections in good repair. 3. Maintain a dry working area. 2.5 INSTALLATION SAFETY How to install Safety DecaIs: Be sure that the installation area is clean and dry. Decide on the exact position before you remove the backing paper. Remove the smallest portion of the split backing paper. Align the decal over the specified area and carefully press the small portion with the exposed sticky backing in place. Slowly peel back the remaining paper and carefully smooth the remaining portion of the decal in place. Small air pockets can be pierced with a pin and smoothed out using the piece of decal backing paper. 2.7 SIGN-OFF FORM ValMetal inc. follows the general Safety Standards specified by the Society of Automotive Engineers (SAE) and the Occupational Safety and Health Administration (OSHA). Anyone who will be operating and/or maintaining the machine must read and clearly understand ALL Safety, Operating and Maintenance information presented in this manual. Do not operate or allow anyone else to operate this equipment until such information has been reviewed. Annually review this information. Make these periodic reviews of SAFETY and OPERATION a standard practice for all of your equipment. We feel that an untrained operator is unqualified to operate this machine A sign-off sheet is provided for your record keeping to show that all personnel who will be working with the equipment have read and understand the information in the Operator s Manual and have been instructed in the operation of the equipment. 1. Use only a hoist, crane or forklift with sufficient lifting capacity and stability to handle the machine. 2. Have 2 men available to maneuver the unit when lifting, moving or installing. 3. Have a qualified electrician to connect power to the machine. 2.6 SAFETY DECALS 1. Keep safety decals and signs clean and readable at all times. 2. Replace safety decals and signs that are missing or have become illegible. 3. Replaced parts that displayed a safety sign should also display the current sign. 4. Safety decals or signs are available from your Dealer Parts Department or the factory. 8 13C R1 - Stationary Unroller 60" & 72" - April 2016

9 SIGN-OFF FORM DATE EMPLOYEE'S SIGNATURE EMPLOYER'S SIGNATURE 13C R1 - Stationary Unroller 60" & 72" - April

10 SECTION 3 - SAFETY DECAL LOCATION The types of decals and locations on the equipment are shown in the illustration below. Good safety requires that you familiarize yourself with the various Safety Decals, the type of warning and the area, particular function related to that area, that requires your SAFETY AWARENESS. Think SAFETY! Work SAFELY! Part No. Illustration Description All operators must read and understand the user s manual prior to use DANGER Do not operate machine without all guards in place. Rotating sprocket and chain can dismember. Keep hands, hair and clothing away from rotating parts. Shut off the power source (electrical, motor, etc.) prior to adjusting or servicing. Failure to heed may result in serious injury or death C R1 - Stationary Unroller 60" & 72" - April 2016

11 The types of decals and locations on the equipment are shown in the illustration below. Good safety requires that you familiarize yourself with the various Safety Decals, the type of warning and the area, particular function related to that area, that requires your SAFETY AWARENESS. Think SAFETY! Work SAFELY! Title : Read Manual num : Title : Rotating Parts num : C Titre : Grease num : 13C Title : Rotating Parts num : REMEMBER - If Safety Decals have been damaged, removed, become illegible or parts replaced without decals, new decals must be applied. New decals are available from your authorized dealer. 13C R1 - Stationary Unroller 60" & 72" - April

12 SECTION 4 - MAINTENANCE 4.1 CHAIN ADJUSMENT 1. Make sure that the adjusting bolts at the idler end are tightened equally. 2. Start the motor and verify that the chain fits well in the sprocket teeth. 3. If an adjustment is necessary TURN OFF THE MOTOR AND LOCK OUT POWER SOURCE, then do the required adjustments. Verify the adjusting bolts on the idler end. 4. Tighten all bolts. When tightening the chain allow it to run at least a full chain revolution to determine if additional adjustments are required. Check tension while machine is loaded. Check frequently during the first 10 hours of operation. Check periodically afterwards. 4.3 LUBRICANT SELECTION Lubricating oil must have a viscosity sufficient to reduce friction and allow the speed reducer to operate smoothly under high load and impact. Consult table below for the choice of lubricant. Where a wide temperature range is expected, the synthetic oil EXXON SHC 629 is recommended. Please keep in touch with our engineering department, especially when operating reducers under special conditions such as high or low speed, high temperature or heavy loads. It takes many hours of running, under full load, for the chain and gear box to reach their highest efficiency. They may, if necessary, be put to work under full load immediately. However, to maximize the lifetime of the machine, it is recommended to run it under gradually increasing loads and to reach a full load only after about 20 hours. 4.2 LUBRICANT AND OIL CHANGE 1. Check oil in gearbox regularly. 2. Grease all bearings monthly. 3. After 100 hours of running, a new worm gear unit should be drained, flushed and refilled with proper oil. 4. Oil should be changed at least every 2500 operating hours or every 6 months, whichever occurs first. Never mix 2 different types of oil. Be sure to drain and wash before using another type of oil. LUBRICANT TABLE Room Temperature ( C) Operation Temperature ( C) GRADE TEXACO SHELL EXXON from -30 C to 0 C Lower than 70 80W90 Meropa 150 Omala 150 Spartan EP 150 SHC 629 from 70 C to 100 C 80W110 Meropa 320 Omala 320 Spartan 320 SHC 629 from 0 C to 25 C Lower than 70 C to 100 C 80W110 Meropa 320 Omala 320 Spartan 320 SHC 629 More than 25 C Lower than 70 C to 100 C 80W140 Meropa 460 Omala 460 Spartan 460 SHC C R1 - Stationary Unroller 60" & 72" - April 2016

13 ... PARTS LIST Stationary Round Bale Unroller 60" & 72" 13C R1 April 2016

14 Drive Unit Product code Width T " T " C R1 - Stationary Unroller 60" & 72" - April 2016

15 Drive Unit Item Part No. Description Qty BASE - DRIVE UNIT 60" BASE - DRIVE UNIT 72" LEFT SIDE - DRIVE UNIT LOWER GEARBOX CC80 SUPPORT PLATE UPPER GEARBOX CC80 SUPPORT PLATE CC80-40L-143TC GEARBOX CC80-40:1 - LEFT SIDE SHAFT (FOR 2HP MOTOR) 1 45-CC80-40L-184TC GEARBOX CC80-40:1 - LEFT SIDE SHAFT (FOR 3HP MOTOR) DRIVE SHAFT - DRIVE UNIT 60" DRIVE SHAFT - DRIVE UNIT 72" RIGHT SIDE - DRIVE UNIT UHMW WEAR PLATE - DRIVE UNIT 60" UHMW WEAR PLATE - DRIVE UNIT 72" C SPROCKET 88C UCF FLANGE BEARING 1 1/2" SPACER - DRIVE UNIT 60" SPACER - DRIVE UNIT 60" TENSIONNER ANGLE BRACKET GUARD GEARBOX CC DRIVE CHAIN TENSIONER B SPROCKET 80B B10H SPROCKET 80B10H CHAIN #80 ASS'Y + 1/2 LINK KEY 3/8" X 3/8" X 2" KEY 3/8" X 3/8" X 1-1/2" KEY 5/16" X 5/16" X 2" BEARING PROTECTOR C FLAT WASHER 1/2" C LOCK WASHER 1/2" C HEX. BOLT 1/2"-13NC x 1 1/2" lg gr C STANDARD NUT 1/2"-13NC C MÉTRIC BOLT M10 X 1.5 X 25MM gr C CARRIAGE BOLT 3/8"-16NC x 1" lg gr C FLAT WASHER 3/8" C LOCK WASHER 3/8" C STANDARD NUT 3/8"-16NC C CARRIAGE BOLT 3/8"-16NC x 3/4" lg gr5 SN C FLANGE NUT 3/8"-16NC C FLAT WASHER 5/16" C FLAT WASHER 5/16" C HEX. BOLT 5/16"-18NC x 3/4" lg gr C NYLON LOCK NUT 3/8"-16NC C HEX. BOLT 3/8"-16NC x 2 1/2" lg gr5 2 13C R1 - Stationary Unroller 60" & 72" - April

16 Base Product code Width " " C R1 - Stationary Unroller 60" & 72" - April 2016

17 Base Item Part No. Description Qty BASE CONVEYOR - LEFT SIDE BASE CONVEYOR - RIGHT SIDE IDLER SHAFT - CONVEYOR 60" IDLER SHAFT - CONVEYOR 72" SUPPORT SPACER TUBE - CONVEYOR 60" SPACER TUBE - CONVEYOR 72" REINFORCEMENT TUBE - CONVEYOR 60" REINFORCEMENT TUBE - CONVEYOR 72" TENSION ROD PLASTIC TENSION WHEEL SPACER CHAIN GUARD WASHER UCF FLANGE BEARING UCF C WASHER 3/4" C STANDARD NUT 3/4"-10NC C JAM NUT 3/4"-10NC C CARRIAGE BOLT 1/2"-13NC x 1 3/4" lg gr C LOCK WASHER 1/2" C STANDARD NUT 1/2"-13NC C WASHER 3/8" C NYLON LOCK NUT 3/8"-16NC C HEX. BOLT 3/8"-16NC x 2 1/2" lg gr5 2 13C R1 - Stationary Unroller 60" & 72" - April

18 Hopper Product code Width " " A B C A A C B B C R1 - Stationary Unroller 60" & 72" - April 2016

19 Hopper 60" Item Part No. Description Qty HOPPER - RIGHT SIDE PANEL HOPPER - LEFT SIDE PANEL HOPPER - REAR PANEL ASS'Y - CONVEYOR 60" HOPPER - REAR PANEL ASS'Y - CONVEYOR 72" HOPPER EXTENSION - CONVEYOR 60" HOPPER EXTENSION - CONVEYOR 72" UPPER PLASTIC PROTECTOR SUPPORT - CONVEYOR 60" UPPER PLASTIC PROTECTOR SUPPORT - CONVEYOR 72" UHMW PLASTIC PROTECTOR - CONVEYOR 60" UHMW PLASTIC PROTECTOR - CONVEYOR 72" LOWER PLASTIC PROTECTOR SUPPORT - CONVEYOR 60" LOWER PLASTIC PROTECTOR SUPPORT - CONVEYOR 72" BELT STRIPE - CONVEYOR 60" BELT STRIPE - CONVEYOR 72" C CARRIAGE BOLT 3/8"-16NC x 1" lg gr C WASHER 3/8" C NYLON LOCK NUT 3/8"-16NC C CARRIAGE BOLT 3/8"-16NC x 1 1/4" lg gr C CARRIAGE BOLT 3/8"-16NC x 1 1/2" lg gr C FLANGE NUT 3/8"-16NC 8 13C R1 - Stationary Unroller 60" & 72" - April

20 5 Feet section Product code Width " " C R1 - Stationary Unroller 60" & 72" - April 2016

21 5 Feet section Item Part No. Description Qty SIDE PANEL ASS'Y - 5 FT SECTION CONVEYOR UPPER PAN - 5 FT SECTION - CONVEYOR 60" CONVEYOR UPPER PAN - 5 FT SECTION - CONVEYOR 72" CONVEYOR LOWER PAN - 5 FT SECTION - CONVEYOR 60" CONVEYOR LOWER PAN - 5 FT SECTION - CONVEYOR 72" CHAIN RETURN SUPPORT - 5 FT SECTION WEAR STRIP ACCESS COVER N WEAR PLATE - 5 FT SECTION - CONVEYOR 60" WEAR PLATE - 5 FT SECTION - CONVEYOR 72" C FLAT WASHER 3/8" - TypeA-Narrow (SAE) C NYLON LOCK NUT 3/8"-16NC C CARRIAGE BOLT 3/8"-16NC x 1" lg gr C LOCK WASHER 3/8" C HEX. BOLT 3/8"-16NC x 1/2" lg gr5 4 13C R1 - Stationary Unroller 60" & 72" - April

22 10 Feet section Product code Width " " A B A A 4 B 3 A A C R1 - Stationary Unroller 60" & 72" - April 2016

23 10 Feet section Item Part No. Description Qty SIDE PANEL ASS'Y - 10 FT SECTION CONVEYOR UPPER PAN - 10 FT SECTION - CONVEYOR 60" CONVEYOR UPPER PAN - 10 FT SECTION - CONVEYOR 72" CENTRAL LOWER PAN - 10 FT SECTION - CONVEYOR 60" CENTRAL LOWER PAN - 10 FT SECTION - CONVEYOR 72" END LOWER PAN - 10 FT SECTION - CONVEYOR 60" END LOWER PAN - 10 FT SECTION - CONVEYOR 72" CHAIN RETURN SUPPORT - 10 FT SECTION ACCESS COVER UHMW SLIDE - CHAIN RETURN - 10 FT SECTION N WEAR PLATE - 10 FT SECTION - CONVEYOR 60" WEAR PLATE - 10 FT SECTION - CONVEYOR 72" RIGHT SIDE STATIONARY UNROLLER GUARD LEFT SIDE STATIONARY UNROLLER GUARD C FLAT WASHER 3/8" - TypeA-Narrow (SAE) C NYLON LOCK NUT 3/8"-16NC C CARRIAGE BOLT 3/8"-16NC x 1" lg gr C LOCK WASHER 3/8" C HEX. BOLT 3/8"-16NC x 1/2" lg gr5 8 13C R1 - Stationary Unroller 60" & 72" - April

24 Legs Kit - 5 Feet Section Product code Width " " C R1 - Stationary Unroller 60" & 72" - April 2016

25 Legs Kit - 5 Feet Section Item Part No. Description Qty FRONT LEG BASE ASS'Y - 5 FT SECTION CROSSBAR SECTION ASS'Y 5 FT SECTION - CONVEYOR 60" CROSSBAR SECTION ASS'Y 5 FT SECTION - CONVEYOR 72" ADJUSTABLE SUPPORT REAR SUPPORT ASS'Y - CONVEYOR 60" REAR SUPPORT ASS'Y - CONVEYOR 72" REAR SUPPORT - SWIVEL SWIVEL SUPPORT ASS'Y BRACE - MALE TUBE 5' SECTION BRACE - FEMALE CHANNEL 5' SECTION C HEX. BOLT 5/8"-11NC X 1-1/2" lg C WASHER 1/2" C HEX. BOLT 1/2"-13NC X 1-1/2" lg C HEX. BOLT 1/2"-13NC X 4-1/2" lg C NYLON LOCK NUT 1/2"-13NC 14 13C R1 - Stationary Unroller 60" & 72" - April

26 Legs Kit - 10 Feet Section Product code Width " " C R1 - Stationary Unroller 60" & 72" - April 2016

27 Legs Kit - 10 Feet Section Item Part No. Description Qty FRONT LEG BASE ASS'Y - 10 FT SECTION CROSSBAR SECTION ASS'Y 10 FT SECTION - CONVEYOR 60" CROSSBAR SECTION ASS'Y 10 FT SECTION - CONVEYOR 72" ADJUSTABLE SUPPORT REAR SUPPORT ASS'Y - CONVEYOR 60" REAR SUPPORT ASS'Y - CONVEYOR 72" REAR SUPPORT - SWIVEL SWIVEL SUPPORT ASS'Y BRACE - MALE TUBE 10' SECTION BRACE - FEMALE CHANNEL 10' SECTION C HEX. BOLT 5/8"-11NC X 1-1/2" lg C WASHER 1/2" C NYLON LOCK NUT 1/2"-13NC C HEX. BOLT 1/2"-13NC X 1-1/2" lg C HEX. BOLT 1/2"-13NC X 4-1/2" lg 10 13C R1 - Stationary Unroller 60" & 72" - April

28 Bale Blocker Product code Width " " C R1 - Stationary Unroller 60" & 72" - April 2016

29 Bale Blocker Item Part No. Description Qty BALE BLOCKER SUPPORT PLATE BALE BLOCKER ARM UCFL FLANGE BEARING UCFL206 X 1-1/4" BALE BLOKER ROLLER ASS'Y - CONVEYOR 60" BALE BLOKER ROLLER ASS'Y - CONVEYOR 72" PLASTIC ROLLER FOR BALE BLOCKER FOOT 1/4" CHAIN (GOLDEN ZINC) PLASTIC SPACER C RAPID LINK 5/16" C STEEL BUSHING 5/8"OD X 1/2"ID X 7/16" C WASHER 1/2" C NYLON LOCK NUT 1/2"-13NC C HEX. BOLT 1/2"-13NC x 1 1/2" lg gr5 6 13C R1 - Stationary Unroller 60" & 72" - April

30 Chain and paddles 2 DIRECTION (UP) DIRECTION (DOWN) The picture above shows how to install the paddles C R1 - Stationary Unroller 60" & 72" - April 2016

31 Chain and paddles Item Part No. Description Qty PADDLE ASS'Y - CONVEYOR 60" PADDLE ASS'Y - CONVEYOR 72" X-ASS CHAIN 81X (See table below) C CARRIAGE BOLT 1/2"-13NC x 1-1/2" lg gr C FLAT WASHER 1/2" - TypeA-Narrow (SAE) C NYLON LOCK NUT 1/2"-13NC -- Chain length by item Item 5ft Section 10ft Section Drive Unit Feet of chain 81X 20 feet 40 feet 10 feet 13C R1 - Stationary Unroller 60" & 72" - April

32 Warranty VALMETAL INC. STATIONARY ROUND BALE UNROLLER WARRANTY Valmetal Incorporated (Valmetal) warrants a new STATIONARY ROUND BALE UNROLLER to be free from defects in material and workmanship, under normal use and service. Obligation under this warranty shall extend for a period of 1 year (12 months) following the date of delivery to the original purchaser and shall be limited to replacement or repair at Valmetal s choice of any parts found to be defective upon inspection by Valmetal. WARRANTY CLAIMS The purchaser claiming under this warranty shall submit a warranty claim in the prescribed form to Valmetal or an Authorized Dealer, for inspection by an authorized company representative. LIMITATIONS OF LIABILITY This warranty is expressly in lieu of all other warranties expressed or implied and all other obligations or liabilities on Valmetal s part of any kind or character, including liabilities for alleged representations or negligence. We neither assume nor authorize any other person to assume on our behalf, any liability in connection with the subsequent sale of the STATIONARY ROUND BALE UNROLLER. This warranty shall not apply to any UNROLLER which has been altered outside the factory in any way if, according to Valmetal, the alterations affected the UNROLLER operation and reliability, or if the UNROLLER has been subject to misuse or accident. This warranty does not apply to parts that are under warranty by the original manufacturer and for which service can be obtained directly through authorized service centers. No warranty is extended to regular service items such as lubricants, paint, knives, v-belts and the like. IN NO EVENT SHALL THE OWNER BE ENTITLED TO RECOVER FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES SUCH AS, BUT NOT LIMITED TO, LOSS OF CROPS, LOSS OF PROFITS OR REVENUE, OTHER COMMERCIAL LOSSES, INCONVENIENCE OR COST OF RENTAL OR REPLACEMENT EQUIPMENT. OPERATOR S MANUAL The Purchaser acknowledges having received training on safe operation of the STATIONARY ROUND BALE UNROLLER and further acknowledges that Valmetal does not assume any liability resulting from the operation of the UNROLLER in any manner other than described in the Operator s Manual supplied at the time of purchase. WARRANTY VOID IF NOT REGISTERED 32 13C R1 - Stationary Unroller 60" & 72" - April 2016

33 13C R1 - Stationary Unroller 60" & 72" - April

34 230 INDUSTRIAL BLVD ST-GERMAIN DE GRANTHAM QUEBEC, CANADA, J0C 1K0 PHONE: FAX: NUMBER 13C R1 APRIL 2016