EBC Brakes EBC Brakes World HQ, Upton Valley Way East, Pineham, Northampton, NN4 9EF United Kingdom. EBC Double-H Sintered

Transcription

1 Vehicle Certification Agency, 1 The Eastgate Office Centre Eastgate Road, Bristol, BS5 6XX, United Kingdom. Switchboard: System and Component Section Fax: MANUFACTURER DETAILS Manufacturer's Representative Manufacturer's Name Manufacturer's Address Trade Name Lining Material reference Steve Payne World HQ, Upton Valley Way East, Pineham, Northampton, NN4 9EF United Kingdom EBC Double-H Sintered TEST DETAILS Reason for Test Location of: Dynamometer Test Dynamometer Date of Test EFI Ltd, Enterprise House, 6/7 Bonville Road, Brislington, Bristol, BS4 5NZ, United Kingdom. Dyno 6 / Microface 13 November 2013 TEST SPECIFICATION AND WORST CASE RATIONALE Back to back pad wear tests carried out on the dyno, following the test procedure found in this test report. CONCLUSION The above mentioned pads were tested in accordance to the Dynamic Test Requirements detailed in this report. Signature Name Position Date LIST OF ANNEXES ANNEX Richard Bailey Type Approval Engineer 13 November 2013 No of PAGES SUBJECT Report Number: page1

2 Application Range Part EFI Material Part Number(s) Material EBC Double-H Sintered FA188 HH AD Competitor Part Number(s) Gold Fren Type 039 (KBA60878) Additional Information None Report Number: page2

3 Test procedure Using Dyno 6, back to back testing was carried out on the EBC Pad and the Gold Fren Pad to the following test schedule: (Ref: Schedule 027) Stage 1: Bedding No. Stops: Initial Disc Temp. Deceleratiom o C 80 to 0 km/h 4 m/s/s Stage 2: Performance Total No. Stops: 16 Initial Disc Temp. 100 o C Group 1: No. Stops: 4 50 to 0 km/h Pressure 3, 10, 17 and 24 Bar Group 2: No. Stops: 4 80 to 0 km/h Pressure 3, 10, 17 and 24 Bar Group 3: No. Stops: to 0 km/h Pressure 3, 10, 17 and 24 Bar Group 4: No. Stops: to 0 km/h Pressure 3, 10, 17 and 24 Bar Stage 3: Fade Run 1: No. Stops: to 0 km/h Deceleratiom 4 m/s/s First 12 stops run with no delay and no cooling Initial Disc Temp. 30 o C Final Disc Temp. 430 o C Last 4 stops are run with cooling and the intitial disc temps are set to 400,300,200 and 100 o C Run 2: Repeat Run 1 Report Number: page3

4 Dynamometer Test Data Vehicle category: Dynamic rolling radius Masses and inertia Test inertia IAdj Brake Test brake disc : Part number: Brake effective radius Brake calliper / brake drum mechanism Manufacturer: Type: kgm2 MD3058X 141 Suzuki GSX 1300R 6 piston Report Number: page4

5 MANUFACTURERS DOCUMENTATION Manufacturers documentation is complete and reflects the agreed specification for the vehicle tested and covers all variants and versions agreed in the worse case rationale Yes FACILITY AND EQUIPMENT CHECKS 1 Risk assessment completed and stored in electronic job folder Yes 2 Facilities and test equipment are appropriate Yes 3 Calibration certificates checked and valid, recorded below Yes Equipment Serial No. Calibration data Load cell Temperature 1 Pressure Regulator sensor LC009 T658-Ch1-33X1 P656-Channel 8 SP002 02/10/ /10/ /10/ /10/2013 Report Number: page5

6 Record of Test results Brake pad / Brake Lining Manufacturer: Make: Type: Test ref EBC Double-H Sintered ( Pt No.FA188 HH) D131113C Geometric check: Average Pad Size Before test () After Test () (),u A 7.84 B 7.83 A 7.8 B 7.83 RH Pad C 7.83 D 7.84 C 7.83 D 7.79 Average RH pad wear () Average pad size () Pad wear LH Pad Average Pad Size Before test () After Test () () A 7.82 B 7.81 A 7.78 B C 7.82 D 7.83 C 7.8 D 7.77 Average pad size () Pad wear Average LH pad wear () Average pad thickness Back plate thickness Overall pad thickness Usable pad thickness Average pad wear Weight Check: Percentage brake pad wear 0.70 % Before test (g) After Test (g) Difference (g) Percentage Difference Left hand % Right hand % Average % Report Number: page6

7 Brake pad / Brake Lining Manufacturer: Make: Type: Test ref Gold Fren 039 (KBA60878) material AD D131113B Geometric check: RH System Inner pad Average Pad Size Before test () After Test () () A 8.1 B 8.08 A 7.98 B C 8.06 D 8.02 C 7.97 D 7.9 Average pad size () Pad wear Average RH pad wear () LH System Inner pad Average Pad Size Before test () After Test () () A 8.18 B 8.14 A 8.03 B C 8.13 D 8.1 C 8.04 D 8.04 Average pad size () Pad wear Average LH pad wear () Average pad thickness 8.10 Back plate thickness 3.82 Overall pad thickness 4.28 Usable pad thickness 4.28 Average pad wear 0.11 Percentage brake pad wear 2.45 % Weight Check: Left hand Right hand Before test (g) After Test (g) Difference (g) Percentage Difference Average Report Number: page7

8 5 Test Documents 6 Appendices Appendix 7 Date of Test: Not Applicable Not Applicable 13 November This test has been carried out and the results reported in accordance with the test schedule described in this test report. Technical Service conducting the test: Vehicle Certification Agency Signed: Richard Bailey Date: 13 November 2013 General Remarks : None Report Number: page8