THE UNITED KINGDOM VEHICLE APPROVAL AUTHORITY. 4. If applicable, name and address of manufacturer's representative: Not applicable

Transcription

1 THE UNITED KINGDOM VEHICLE APPROVAL AUTHORITY VCA Headquarters 1 The Eastgate Office Centre Eastgate Road Bristol, BS5 6XX United Kingdom Switchboard: +44 (0) Main Fax: +44 (0) enquiries@vca.gov.uk Web: COMMUNICATION CONCERNING APPROVAL GRANTED OF A TYPE OF REAR UNDERRUN PROTECTIVE DEVICE (RUPD), PURSUANT TO REGULATION NO 58 Approval No: 58R Extension 01 Reason(s) for Extension: To cover: 1) Information update for the Turkish assembly plant 2) Drawing update 1. Trade name or mark of device: Volvo or Renault 2. Type of device: RUP-FIX2 3. Name and address of manufacturer: Volvo Truck Corporation SE Göteborg Sweden 4. If applicable, name and address of manufacturer's representative: Not applicable 5. Characteristics of the device (dimensions and its fixing elements): See manufacturer's documentation 6. Test conducted on a on a representative part of the chassis of a vehicle 7. Position on the device of the points of application of the test forces: P1: 955 mm from centre-line P2: 425 mm from centre-line P3: On centre-line An executive agency of the Department for Transport ESK

2 REGULATION NO Maximum horizontal deflection observed during and after the application of the test forces in annex 5: P1: 102 mm during; 66 mm after P2: 13.5 mm during; 3 mm after P3: 8.1 mm during; 3 mm after 9. Vehicles on which the device may be installed (if applicable): Any vehicle 10. Maximum mass of vehicle on which the device may be installed: kg 11. Device submitted for approval on: As before (15 30 September 2008) 12. Technical service responsible for conducting approval tests: Vehicle Certification Agency 13. Date of report issued by that service: As before (2 December 2008) 14. Number of report issued by that service: As before (ESJ194110) 15. Approval GRANTED in respect of the RUPD 16. Position of approval mark on the device: Self-adhesive decal on the device 17. Place: BRISTOL 18. Date: 22 JUNE Signature: A W STENNING Head of Technical and Quality Group 20. The following documents, bearing the approval number shown above, are available upon request: - Drawings, diagrams and layout plans of the components of the structure considered to be of importance for the purposes of this Regulation - Where applicable drawings of the protective devices and their position on the vehicle. An executive agency of the Department for Transport ESK

3 VCA Headquarters 1 The Eastgate Office Centre Eastgate Road Bristol, BS5 6XX United Kingdom Switchboard: +44 (0) Main Fax: +44 (0) enquiries@vca.gov.uk Web: THE UNITED KINGDOM VEHICLE APPROVAL AUTHORITY COMMUNICATION CONCERNING THE GRANTING OF EEC TYPE APPROVAL RELATING TO REAR UNDERRUN PROTECTION AND LIQUID FUEL TANKS FOR MOTOR VEHICLES AND THEIR TRAILERS PURSUANT TO EEC DIRECTIVE 70/221/EEC AS LAST AMENDED BY 2006/20/EC Type Approval No: e11*70/221*2006/20*10166*01 Reason for Extension: To cover: 1) Information update for the Turkish assembly plant 2) Drawing update SECTION I 0.1 Make (trade name of manufacturer): Volvo or Renault 0.2 Type and general commercial description(s): RUP-FIX2 0.3 Means of identification of type, if marked on the separate technical unit: Not applicable Location of that marking: Not applicable 0.4 Category of vehicle (1) (3) : Not applicable 0.5 Name and address of manufacturer: Volvo Truck Coporation SE Göteborg Sweden 0.7 In the case of components and separate technical units, location and method of affixing of the EC approval mark: Self-adhesive decal on the protective device An executive agency of the Department for Transport ESK

4 2006/20/EC STU 0.8 Addresses of assembly plants: Volvo Truck Coporation SE Göteborg Sweden Volvo do Brazil Veiculos Ltda Caixa Postal Curitiba, Pr Brazil Renault Trucks Bourg-en-Bresse France Volvo Europe Truck NV Smalleheerweg Gent Oostaker Belgium Volvo Vostok 18 Tulskoye Shosse Kaluga Russia Renault Trucks Blainville-sur-Orne France Only for Renault Trucks: Karsan Otomotiv Sanayii Ve Tic. A.Ş Akçalar Sanayi Bölgesi Akçalar Nilüfer Bursa Turkey SECTION II 1. Additional information (where applicable): see Addendum 2. Technical service responsible for carrying out the tests: Vehicle Certification Agency 3. Date of test report: As before (2 December 2008) 4. Number of test report: As before (ESJ194110) 5. Remarks (if any): see Addendum 6. Place: BRISTOL 7. Date: 22 JUNE Signature: A. W. STENNING Head of Technical and Quality Group 9. The index to the information package lodged with the approval authority, which may be obtained on request, is attached. ESK An executive agency of the Department for Transport 2

5 2006/20/EC STU ADDENDUM to EEC Type Approval Certificate No: e11*70/221*2006/20*10166*01 concerning the type approval of a separate technical unit with regard to a rear underrun protective device (Directive 70/221/EEC as last amended by Directive 2006/20/EC) 1. Additional information 1.1 Construction Material: Aluminium STD or equivalent Method of affixing: Bolted to frame side members Dimension of the device: 2352 mm length, 105 mm height (maximum) 1.2 Maximum technical permissible mass of the vehicle on which the device is to be mounted: 50000kg 1.3 Restrictions of the use of the device (if any): No restrictions 5. Remarks: None (1) (2) (3) Delete where inapplicable If the means of identification of type contains characters not relevant to describe the vehicle, component or separate technical unit types covered by this type-approval certificate, such characters shall be represented in the documentation by the symbol '?' (e.g. ABC??123??). As defined in Annex II Section A to Directive 70/156/EEC. ESK An executive agency of the Department for Transport 3

6 APPROVAL NUMBER: e11*70/221*2000/8*10166*01 INFORMATION PACKAGE CONTENTS INDEX REVISION NUMBER: 01 (One) Total number of sheets: Number of separate drawings: Number of separate photographs: 10 (Ten) 0 (Nil) 0 (Nil) Reasons for Revision: See approval certificate Revision date & Office stamp ESK An executive agency of the Department for Transport

7 Job ref.: ESK Information document concerning the type approval of a separate technical unit according to Directive 70/221/EEC as last amended by Directive 2006/20/EC and Regulation No. 58, 02 series of amendments REAR UNDERRUN PROTECTIVE DEVICE SEPARATE TECHNICAL UNIT RUP-FIX2 RUP-FIX2 1/10 e11*70/221*2006/20*10166*01rev01 & E11 58R Ext.01 Rev.01

8 CONTENTS Reason of extensions/revisions... page 02 Extensions/Revisions history... page General... page General construction characteristics of the vehicle(s)... page Masses and dimensions... page Bodywork... page 04 Appendixes... page 06 REASON EXTENSIONS/REVISIONS - Extension 01, revision 01 - Information update for the Turkish assembly plant - Bar drawing update EXTENSIONS/REVISIONS HISTORY Extension 00, revision New EC/ECE approvals RUP-FIX2 2/10 e11*70/221*2006/20*10166*01rev01 & E11 58R Ext.01 Rev.01

9 INFORMATION DOCUMENT relating to EC/ECE type-approvals as a separate technical unit with respect of a rear underrun protective device (Directive 70/221/EEC as last amended by 2006/20/EC and Regulation No. 58, 02 series of amendments) 0. GENERAL 0.1. Make: Volvo or Renault 0.2. Type and general commercial description(s): RUP-FIX Name and address of manufacturer: VOLVO TRUCK CORPORATION GOTHENBURG SWEDEN 0.7. In the case of components and separate technical units, location and method of affixing of the approval mark: Self-adhesive decal on protective device 0.8. Address(es) of assembly plant(s): VOLVO TRUCK CORPORATION GOTHENBURG SWEDEN VOLVO EUROPA TRUCK NV SMALLEHEERWEG GENT OSTAKKER BELGIUM VOLVO DO BRAZIL VEICULOS LTDA CAIXA POSTAL CURITIBA, PR BRAZIL VOLVO VOSTOK 18 TULSKOYE SHOSSE KALUGA RUSSIA RENAULT TRUCKS BOURG-EN-BRESSE FRANCE RUP-FIX2 3/10 e11*70/221*2006/20*10166*01rev01 & E11 58R Ext.01 Rev.01

10 RENAULT TRUCKS BLAINVILLE-SUR-ORNE FRANCE KARSAN OTOMOTIV SANAYII VE TIC. A.Ş. AKÇALAR SANAYI BÖLGESI AKÇALAR NILÜFER BURSA TÜRKIYE* * only for Renault Trucks 1. GENERAL CONSTRUCTION CHARACTERISTICS OF THE VEHICLE(S) on which the device is intended to be fitted in so far as they relate to the rear underrun protection (attach photographs and/or drawings): 1.1. Minimum sum of the moments of inertia about the horizontal axis of the chassis side members in cross-section 2,48 x 10 7 mm Distance between the chassis side members at the mounting points of the device: 846 to 862 mm 2. MASSES AND DIMENSIONS 2.1. Technically permissible maximum laden mass: kg 3. BODYWORK 3.1. Full description and/or drawing of the rear underrun protection device (including mounting and fittings): The underrun protection device consists of a horizontal underrun guard, with pressed rubbers at the outer ends, fixed by 2 x 2 M14 bolts to brackets mounted by 2 x 6 and 2 x 4 M14 bolts to the frame side members; bolts class 8,8 minimum following STD 5511,15. RUP-FIX2 4/10 e11*70/221*2006/20*10166*01rev01 & E11 58R Ext.01 Rev.01

11 See appendixes. RUP-FIX2 5/10 e11*70/221*2006/20*10166*01rev01 & E11 58R Ext.01 Rev.01

12 APPENDIXES Underrun guard... drawing Rubber... drawing Brackets... drawing (alternative) drawing RUP-FIX2 6/10 e11*70/221*2006/20*10166*01rev01 & E11 58R Ext.01 Rev.01

13 Aluminum STD 1142,04 or equivalent RUP-FIX2 7/10 e11*70/221*2006/20*10166*01rev01 & E11 58R Ext.01 Rev.01

14 RUP-FIX2 8/10 e11*70/221*2006/20*10166*01rev01 & E11 58R Ext.01 Rev.01

15 Thickness 6 mm Steel (eq. VSHR490) STD 1126,62 (for info STD ) or equivalent RUP-FIX2 9/10 e11*70/221*2006/20*10166*01rev01 & E11 58R Ext.01 Rev.01

16 Thickness 8 mm Steel (eq. VSHR490) STD 1126,62 (for info STD ) or equivalent RUP-FIX2 10/10 e11*70/221*2006/20*10166*01rev01 & E11 58R Ext.01 Rev.01