4. If applicable, name and address of manufacturer's representative: Not applicable

Transcription

1 VCA Headquarters 1 The Eastgate Office Centre Eastgate Road Bristol, BS5 6XX United Kingdom Switchboard: +44 (0) Main Fax: +44 (0) enquiries@vca.gov.uk Web: THE UNITED KINGDOM VEHICLE APPROVAL AUTHORITY Rev 1/01 COMMUNICATION CONCERNING THE APPROVAL GRANTED OF A FUEL TANK PURSUANT TO REGULATION NO 34 Approval No: 34RIIIU+A Trade name or mark of the fuel tank: SB Components 2. Manufacturer s name for the type of fuel tank: SBADBLUECOMBI 3. Manufacturer's name and address: SB Components International Ltd Millennium Works Enterprise Way Wisbech Cambridgeshire PE14 0SB United Kingdom 4. If applicable, name and address of manufacturer's representative: Not applicable 5. Brief description of fuel tank and fuel 5.1 Characteristics of fuel tank: See manufacturer s documentation 5.2 For fuel tanks made of a plastic material, state material and trade name or mark: Not applicable 6. Submitted for approval on: 11 November Technical service responsible for conducting approval tests: Vehicle Certification Agency ESL An Executive Agency of the Department for Transport 1

2 REGULATION NO 34RIII 8. Date of report issued by that service: 20 June Number of report issued by that service: ESL Reason(s) for extension (if applicable): Not applicable 11. Approval GRANTED 12. Position of Approval mark on the fuel tank: On top surface of tank, unless otherwise required for visibility on vehicle. 13. Place: BRISTOL 14. Date: 20 June Signature: A W STENNING Head of Technical and Quality Group 16. The index to the information package lodged with the approval authority, which may be obtained on request, is attached. ESL An Executive Agency of the Department for Transport 2

3 Application for approval of a type of fuel tank in accordance with UNECE Regulation 34, part III 0. GENERAL 0.1. Make (trade name of manufacture): SB Components 0.2. Type designation: SBADBLUECOMBI 0.5 Name and address of the manufacturer: SB Components International Ltd Millennium Works, Enterprise Way Wisbech, Cambridgeshire, PE14 0SB 0.8 Address(es) of assembly plant(s): As above 3. POWER PLANT Fuel: Diesel Fuel tank(s) Service fuel tank(s) Capacity, material: Litres 2mm Stainless Steel (With separate Adblue reservoir) Drawing and technical description of the tank(s) with all the connections and all lines of the breathing and venting system, locks, valves, fastening devices: See attachments

4 NOTE: THIS NUMBER IS ONLY APPLICABLE FOR CERTAIN TANKS NOTE: THIS DRAWING IS NOT TO SCALE ISO 9001:2008 Z:\SB\AutoCAD\Drawings\Customers\SB UK (Hauliers Bodybuilders etc)\sb Components\Test Tanks\SBADBLUECOMBI.dwg, 17/06/ :05:14 MANUFACTURED AND TESTED TO EC DIRECTIVE ECER34 PRESSURE TEST TO.3 BAR SBC Number: Drawing number: Dealership: End User: Drawn by: Date drawn: Approved by: Vehicle Specification: Capacity: Linking to: Cross over spec: Fitted position: SBADBLUECOMBI Ash Manning 9th June 2011 James Warren Ground clearance: Sender type: Exhaust spec: Battery location: AdBlue location: Fifth wheel spec: Strap Lengths: Press Notes: Material: Finish (Paint): SO/S&F/SBI/SBE: Quantity: Punch program: Robot program: Issued by & date: Date required: Other notes: 2mm Stainless Steel Yes No MIN CAPACITY 40LTRS MAX CAPACITY 1000 LTRS. Revision No. 0 Previous SBC. 0 No. Description Date By VCA No. 34RIII02012(4/5/6) Third Angle Projection Units of measure: MM Tolerance: Linear ± 2MM Hole centres ± 1MM Holes ± 0.5MM Angular ± 1.5 Unless otherwise stated Welding MIG: To be in accordance with BS4872 part1 (Unless otherwise stated). TIG: To be in accordance with BSEN 287 part (Unless otherwise stated). Millenium works Enterprise Way Wisbech, Cambs, PE14 0SB, England Tel: Fax: REGISTERED FIRM UKAS MANAGMENT SYSTEMS 0028

5 Z:\SB\AutoCAD\Drawings\Customers\SB UK (Hauliers Bodybuilders etc)\sb Components\Test Tanks\SBSS 1.5 BARREL.dwg, 17/06/ :42:40 MANUFACTURED AND TESTED TO EC DIRECTIVE ECER34 MATERIAL SPECIFICATION: ALUMINIUM BAR GRADE 6082T6 TOLERANCE: TAPPED OUT TO 1/2" X 14TPI BSP HSSISO6H THREAD LINEAR: ± 0.1MM HOLE CENTRES: ± 0.50MM HOLES: ± 0.25MM ANGULAR: ± 1 UNLESS OTHERWISE STATED SBC NUMBER STRAP LENGTH REVISIONS TO DRAWING ISSUE NUMBER 0 DRAWING NUMBER SB SS 1 2" BSP BARREL SENDER LENGTH DEALERSHIP/END USER EXHAUST SPECIFICATION THIRD ANGLE PROJECTION VEHICLE MAKE/MODEL 6X2/4X2/OTHER SIDE SKIRTS BATTERY LOCATION MADE IN GREAT BRITAIN CAPACITY MAIDDIT/NS/OS/ROC LINKING TO CROSS OVER SPEC FITTED POSITION GROUND CLEARANCE FIFTH WHEEL TYPE FIFTH WHEEL POSITION ADBLU TANK POSITION DRAWN BY DATE DRAWN PREVIOUS DWG/ISSUED ASH MANNING 17TH JUNE 2011 FIRST ISSUE OTHER NOTES PART NO: SSFS0015 NOTE: PLEASE REMOVE ALL SHARP EDGES THIS DRAWING AND DESIGN ARE THE PROPERTY OF SB COMPONENTS INTERNATIONAL LTD. THE CONTENTS MUST NOT BE DISCLOSED TO AN UNAUTHORISED THIRD PARTY

6

7 Z:\SB\AutoCAD\Drawings\Customers\SB UK (Hauliers Bodybuilders etc)\sb Components\Test Tanks\SB SS FILLER NECK & CAP.dwg, 17/06/ :05:51 MANUFACTURED AND TESTED TO EC DIRECTIVE ECER SBC NUMBER STRAP LENGTH REVISIONS TO DRAWING ISSUE NUMBER 0 DRAWING NUMBER SB FILLER NECK & CAP SENDER LENGTH DEALERSHIP/END USER EXHAUST SPECIFICATION THIRD ANGLE PROJECTION VEHICLE MAKE/MODEL 6X2/4X2/OTHER SIDE SKIRTS BATTERY LOCATION MADE IN GREAT BRITAIN CAPACITY MAIDDIT/NS/OS/ROC LINKING TO CROSS OVER SPEC FITTED POSITION GROUND CLEARANCE FIFTH WHEEL TYPE FIFTH WHEEL POSITION ADBLU TANK POSITION DRAWN BY DATE DRAWN PREVIOUS DWG/ISSUED RICHARD SMITH 23RD MARCH 2007 FIRST ISSUE OTHER NOTES S/S SPUNNECK PART NO: SSTN000D CAP PART NO: FTC00002 THIS DRAWING AND DESIGN ARE THE PROPERTY OF SB COMPONENTS INTERNATIONAL LTD. THE CONTENTS MUST NOT BE DISCLOSED TO AN UNAUTHORISED THIRD PARTY