Verplas Self-Seal Coupling Leakage Test. Prepared for : Verplas Limited. 25 February Test report number Page 1 of 11
|
|
- Lorraine Wood
- 5 years ago
- Views:
Transcription
1 Verplas Self-Seal Coupling Leakage Test Prepared for : Verplas Limited 25 February 2013 Page 1 of 11
2 Prepared by Name M Swainson Position Principal Engineer Date 25 th February 2013 Signature Approved on behalf of BRE Name D Butler Position Manager, HVAC Engineering Date 25 th February 2013 Signature BRE Garston WD25 9XX T + 44 (0) F + 44 (0) E enquiries@bre.co.uk This report may only be distributed in its entirety and in accordance with the terms and conditions of the contract. Test results relate only to the items tested. BRE has no responsibility for the design, materials, workmanship or performance of the product or items tested. This report does not constitute an approval, certification or endorsement of the product tested. This report is made on behalf of BRE. By receiving the report and action on it, the client or any third party relying on it accepts that no individual is personally liable in contract, tort or breach of statutory duty (including negligence). Page 2 of 11
3 Contents 1 Introduction 4 2 Details of Tests carried out 5 3 Test Results 8 4 Conclusions 11 Page 3 of 11
4 1 Introduction Verplas Limited approached BRE to undertake testing of an innovative plastic duct coupling for air leakage. The performance specification for plastic duct used in ventilation applications is covered by the HVAC, DW/154, Specification for Plastic Ductwork, First Edition DW/154 refers to HVCA, DW/143, A Practical Guide to - Ductwork Leak Testing, Fifth Edition, 2000, which provides guidance on how testing of leakage should be undertaken. A proposal was prepared, submitted and accepted by Verplas Limited for testing to DW/154. The couplings submitted for testing were: Verplas System 125 Round Pipe to Fitting Self-Seal Couplings The couplings were delivered to BRE and were to be tested for air leakage to Class A, low pressure ducts as defined in DW/143. Page 4 of 11
5 2 Details of Tests carried out A set of air leakage tests were undertaken following the guidance set out in HVCA, DW/143, A Practical Guide to - Ductwork Leak Testing, Fifth Edition The test was undertaken to assess the leakage for Class A duct, low pressure. The duct layout used was taken from Test method for - Central mechanical supply and exhaust ventilation system packages with heat recovery used in a single dwelling. Version Date; 22/08/2008. V2.0. This test method defines duct layouts used for testing mechanical ventilation products used in dwellings in the UK. To test a sample of couplings, a representative duct layout for a typical UK dwelling was identified as a long branch duct with four terminals. The location of the couplings and duct seals is shown in Figure m 1.0m Verplas Self-Sealing Couplings Duct ends sealed 0.5m 1.5m 1.5m 1.5m 1.5m Figure 1: Long branch duct with four terminals used for testing coupling air tightness. Verplas provided 15 samples of the 125 mm diameter Self-Seal Couplings and these were used to make up the test configuration shown in Figure 1. The Verplas Self-Seal Couplings supplied for this test were designed to fit between straight lengths of 125 mm diameter duct and fittings with male connections. The couplings can be seen with a straight and 90 bend in Figure 2. Page 5 of 11
6 Figure 2 : Verplas Self-Seal Couplings fitted between straight duct and 90 bend. Test instruments used during measurement of the air leakage rate. Variable Instrument used for measurement Calibration Date of calibration Air flow rate Duct pressures Brookes 5853E Chell Display CCD100 Furness Controls FCO332 Chell (UKAS) 25 th July 2012 Furness Controls (UKAS) 22 nd March 2012 The test layout of the duct prior to testing can be seen in Figure 3. No additional fixing or restraint was used on the ductwork as a check of the ability of the seals to prevent separation under pressure conditions. Page 6 of 11
7 Figure 3 : Test layout of duct with Verplas Self-Seal Couplings fitted between straight duct, 90 bends and Tee-Pieces. Page 7 of 11
8 3 Test Results The measured air flow rates during the leakage testing are shown in Table 1. Positive pressure Negative pressure Pressure applied (Pa) Air flow rate (l/s) Pressure applied (Pa) Air flow rate (l/s) Table 1 Measured leakage rates The duct surface area was calculated as: 6 off, 1.5 m x mm diameter ducts = 3.54 m 2. Page 8 of 11
9 DW/143 expresses the results as a function of duct surface area, therefore for the defined duct layout; long branched duct with four terminals, the leakage per meter square of duct are as shown in Table 2. Positive pressure Negative pressure DW/143 Maximum leakage for Class A ductwork Pressure applied (Pa) Leakage rate (l/s/m 2 ) Pressure applied (Pa) Leakage rate (l/s/m 2 ) Leakage rate (l/s/m 2 ) Table 2 Calculated leakage rate per unit area of duct. Page 9 of 11
10 2.0 Leakage (l/s/m 2 ) Air flow rate - Verplas Connectors (l/s/m²) DW143 Leakage Class A (l/s/m²) [htitle] Building Research Establishment Ltd [autoyear] Page 10 of Static pressure (Pa) Figure 4 : Leakage rate of Verplas Self-Seal Couplings compared to maximum leakage for Class A ductwork.
11 4 Conclusions From the measured leakage rates presented in Table 2 and Figure 4, it is evident that the Verplas Self- Seal Couplings achieved a level of leakage substantially lower than the maximum allowed for Class A duct as defined in DW/143. At all positive and negative pressures in the tests, there was no sign of the duct seals separating, indicating that they are able to withhold positive and negative pressures up to 500 Pa, without requiring additional restraint. ==============REPORT ENDS============= Page 11 of 11
SAP PCDB: Test method for central exhaust ventilation system packages used in a single dwelling
SAP PCDB: Test method for central exhaust ventilation system packages used in a single dwelling 1 Introduction This test method is based closely on the European Standard BS EN 13141-6:2004 and must be
More informationENGINEERING REPORT RE15012
Analysis of Proposed Load Restraint Configurations for Round Subject Cotton Modules Client Cotton Australia Pty Ltd Client Address 115 Campbell St, Toowoomba, QLD 4350 Revision 0 Date 10/02/2015 Report
More informationTABBED ACCESS DOOR RANGE
TABBED PRODUCT Insulated double skinned tabbed access door. Fire Retardant double skinned tabbed access door. Available Options 25mm Deep. 50mm Deep. Factory fitted safety retaining chain. Factory fitted
More informationMicrogeneration Installation Standard: MCS
Microgeneration Installation Standard: MCS 001-01 MCS Contractor Certification Scheme Requirements Part 1: Requirements for MCS Contractors Issue 3.1 This Microgeneration Installation Standard is the property
More informationENGINEERING REPORT RE11049
Subject Client Client Address Analysis of Proposed Load Restraint Configurations for Round Cotton Modules B-Safe Winches Australia (a Division of Dangerous Goods Equipment Pty Ltd) PO Box 4029 Eight Mile
More informationBS EN :2011 BS :2002+A1:2013 UKSRG Guidelines-4:2011 EN124:1994 HA104\09
PendulumTest(s) carried out in accordance with: BS EN 13036-4:2011 BS 7976-2:2002+A1:2013 UKSRG Guidelines-4:2011 EN124:1994 HA104\09 On behalf of: Fibrelite Limited. Prepared by: Phil Nolan GET-A-GRIP!
More informationARAI/TA(4G)/SMS/D680/ Dated 28 Jan 2010
CERTIFICATE FOR COMPLIANCE TO THE CENTRAL MOTOR VEHICLES RULES M/s SMS Autoline Equipments Pvt. Ltd. Plot No.AP215, 6 th Street I Block, Vallalar Colony, Anna Nagar (West) Chennai 600 040 Cert Annex Drg
More informationRD-2000 Round Control Dampers
RD-000 Round Control Dampers Product Bulletin Code No. LIT-8105 Issued February 5, 010 Supersedes July, 009 Johnson Controls provides top-quality, low-leakage RD-000 Round Control Dampers for use in Heating,
More informationLEAKAGE CLASS ACHIEVED? Wöhler DP 700 LEAKAGE TEST ON VENTILATION SYSTEMS AND COMPONENTS. The Measure of Technology GRAPHIC COLOR DISPLAY GRAPHIC
LEAKAGE CLASS ACHIEVED? GRAPHIC COLOR DISPLAY COLOR DISPLAY GRAPHIC LEAKAGE TEST ON VENTILATION SYSTEMS AND COMPONENTS The Measure of Technology Made in Germany Leakage Tester Just 3 entries to classify
More informationARAI/TA(4G)/GEN-MAINT/EXOSCAN-V/ Dated 26 th Mar 2009 CERTIFICATE FOR COMPLIANCE TO THE CENTRAL MOTOR VEHICLES RULES
CERTIFICATE FOR COMPLIANCE TO THE CENTRAL MOTOR VEHICLES RULES M/s Gen-Maint 106-107, New Diamond Premises Coop. Soc. Ltd. Off. Western Express Highway Goregaon (E) Mumbai 400 063 Cert Annex Drg Tot al
More informationTechnical Services Report
SATRA Technology Centre Ltd Wyndham Way, Telford Way Industrial Estate Kettering, Northamptonshire NN16 8SD United Kingdom Tel: +44 (0) 1536 410000. Fax +44 (0) 1536 410626 e-mail: info@satra.co.uk Firm:
More informationARAI/TA(4G_RV)/SMS/D680/ Dated 21 st Mar 2015 CERTIFICATE FOR COMPLIANCE TO THE CENTRAL MOTOR VEHICLES RULES
CERTIFICATE FOR COMPLIANCE TO THE CENTRAL MOTOR VEHICLES RULES M/s SMS Autoline Equipments Pvt. Ltd. Plot No.AP215, 6 th Street, I Block, Vallalar Colony, Anna Nagar (West) Chennai 600 040 Cert Annex Drg
More informationEVALUATION SUBJECT: >B< MAXIPRO PRESS FITTINGS FOR AC AND REFRIGERATION APPLICATION
ICC-ES Report PMG-1440 Issued 09/2017 This report is subject to renewal 09/2018 EVALUATION SUBJECT: >B< MAXIPRO PRESS FITTINGS FOR AC AND REFRIGERATION APPLICATION DIVISION: 23 00 00 HEATING, VENTILATING
More informationBallast Water Management Surveyor checklist
Ballast Water Management Surveyor checklist Last updated: July 2017 This document is uncontrolled if printed, please refer to the Maritime New Zealand website for the latest version. Use this checklist
More informationARAI/TA (4G)/AIRVISOR/AVG500/ Dated 17 th Apr 2017
Airvisor Technologies Pvt. Ltd. H-155, Adhyapak Nagar, Nangloi, New Delhi 110041. CERTIFICATE FOR COMPLIANCE TO THE CENTRAL MOTOR VEHICLES RULES Cert Annex Drg Total 1 7 0 8 pgs Exhaust Gas Analyzer Model
More informationNEW. Iris Control Damper (ICD) For adjustment and measuring of airflow. Features. Quick and simple installation and maintenance
March 29 Iris Control Damper (ICD) NEW Iris Control Damper (ICD) For adjustment and measuring of airflow Features Quick and simple installation and maintenance Extended spigot connections 1% opening capacity
More informationMicrogeneration Installation Standard: MCS 023
Microgeneration Installation Standard: MCS 023 Additional Requirements for MCS Contractors to demonstrate PAS2030 equivalence for the installation of Microgeneration technologies. Issue 2.1 This Microgeneration
More informationFD-C Series. Circular Single Blade Externally Resettable Combination Fire and Volume Control Damper B RITAI N
V1175 FD-C Series Circular Single Blade Externally Resettable Combination Fire and Volume Control Damper ES classified fire dampers with reduced smoke leakage characteristics (BS E 1366-2) Aerodynamically
More informationVariable Air Volume Dampers
OVAV 2000 SERIES OPTIMA VAV DAMPERS Overview OPTIMA make Variable Air Volume (OVAV) box is a part of an Air Conditioning system. It is located inside the duct work. VAV Dampers are designed to control
More informationAmendment 69 FR (20 December 2004) Section 5 Hydraulic brake hose, brake hose assemblies, and brake hose end fittings ESN270529
Vehicle Certification Agency 1 The Eastgate Office Centre Eastgate Road Bristol BS5 6XX United Kingdom Telephone: +44 (0) 117 951 5151 Fax: +44 (0) 117 952 4103 Email: enquiries@vca.gov.uk www.dft.gov.uk/vca/
More informationRotating Vane Anemometer
Ventilation Testing Rotating Vane Anemometer Alnor Model RVA801 AIRFLOW Model LCA301 Operation and Service Manual Copyright TSI Incorporated / 2007-2008 / All rights reserved. Address TSI Incorporated
More informationGUIDE TO CLEANING grease extraction systems
Introduction In a commercial kitchen, canteen or catering environment, it s inevitable that grease will build up over time, coating surfaces and cooking equipment. Although your regular cleaning staff
More informationSEMI RIGID THE PROFESSIONALS CHOICE
SEMI RIGID THE PROFESSIONALS CHOICE for efficient, high performance MVHR ductwork installations. SAP APPENDIX Q LISTED brookvent.co.uk FITTING OUTLINE THE PROFESSIONALS CHOICE for efficient, high performance
More informationUL TEST REPORT AND PROCEDURE
Issue Date: 2012-03-23 Page 1 of 16 Report Reference # E186249-A202-UL UL TEST REPORT AND PROCEDURE Standard: Certification Type: CCN: Product: Model: Rating: UL 60950-1, 2nd Edition, 2011-12-19 (Information
More information2018 Product Training
2018 Product Training Course 1: City Multi VRF DESIGN This course is designed for consulting engineers, specifiers, installation contracting engineers, and sales engineers who require detailed knowledge
More informationTABLE OF CONTENTS FOREWORD... 2 INTRODUCTION SCOPE NORMATIVE REFERENCES DEFINITIONS AND ABBREVIATIONS... 3
TITLE SPECIFICATION FOR MEDIUM VOLTAGE DATE: FEBRUARY 2015 PAGE: 1 OF 25 TABLE OF CONTENTS Page FOREWORD... 2 INTRODUCTION... 3 1 SCOPE... 3 2 NORMATIVE S... 3 3 DEFINITIONS AND ABBIATIONS... 3 4 REQUIREMENTS...
More informationSRP BUSINESS SOLUTIONS
FY19 ELECTRIC VEHICLE CHARGER PORT REBATE REQUEST ELECTRIC VEHICLE CHARGER REBATE PROGRAM OVERVIEW As an SRP business customer, you can earn up to $500 for each Level 2 electric vehicle (EV) charging port
More informationARAI/TA(4G_RV)/HORIBA/MEXA 584L/ Dated 25 Mar 2014
CERTIFICATE FOR COMPLIANCE TO THE CENTRAL MOTOR VEHICLES RULES M/s Horiba India Pvt. Ltd. Room 1521, 15 th Floor, Eros Corporate Tower, Nehru Place New Delhi 110 019 Cert Annex Drg Total 1 7 0 8 pgs Exhaust
More informationAir Conditioning And Heater Module Assembly Removal And Installation
Page 1 of 16 2006 Cadillac CTS : Heating, Ventilation, & Air Conditioning > Repair Instructions > Air Conditioning And Heater Module Assembly Removal And Installation Air Conditioning And Heater Module
More informationSTAINLESS STEEL FORGED FITTINGS 3000lb 304/304L & 316/316L Forged Stainless Steel Fittings Product Specifications
STAINLESS STEEL FORGED FITTINGS 3000lb 304/304L & 316/316L Forged Stainless Steel Fittings Product Specifications Manufactured in ISO9000:2000 Facility Manufactured to ASTM/ASME A182/SA182 Items conform
More information10-Feb-14. VCA job number: CSP Date: 10 February Dear Sirs,
VCA job number: CSP286498 Date: 10 February 2014 Dear Sirs, 1. The vehicle type / component described on the attached approval(s) has been tested and meets the requirements of the ECE Regulation / EEC
More informationIAQ-CALC TM Indoor Air Quality Meter
ENERGY AND COMFORT Indoor Air Quality IAQ-CALC TM Indoor Air Quality Meter Model 7515 Operation and Service Manual Copyright TSI Incorporated / May 2007 / All rights reserved. LIMITATION OF WARRANTY AND
More informationDD Series. Duct Regulating Dampers M A N U F A C T U R E R S O F A I R, F I R E A N D S M O K E C O N T R O L P R O D U C T S. Two blade options.
Duct Regulating Dampers Two blade options. DW144 compliant Four case options Three control options Nylon bushes as standard Suitable for vertical and horizontal ducted systems. M A N U F A C T U R E R
More informationBostik Intucrylic Sealant INTUMESCENT ACRYLIC JOINT SEALANT
Bostik Intucrylic Sealant INTUMESCENT ACRYLIC JOINT SEALANT Date: 02 July 2014 Fact Sheet No.: TDS00644 YOUR SMART ADVANTAGES High levels of certification Will not slump in joints up to 30mm Prevents passage
More informationTechnical Papers supporting SAP 2009
Technical Papers supporting SAP 29 A meta-analysis of boiler test efficiencies to compare independent and manufacturers results Reference no. STP9/B5 Date last amended 25 March 29 Date originated 6 October
More informationVOLUME CONTROL / REGULATING DAMPERS
VOLUME CONTROL / REGULATING S PRODUCT RANGE Model Range Includes A - Multi-Leaf. (Flanged - Rectangular Duct) B - Multi-Leaf. (Slip joint / Spigot - Rectangular Duct) C - Multi-Leaf. (Slip joint / Spigot
More informationElectric Vehicles and the Environment (EVE IWG)
Submitted by the EVE informal working group Electric Vehicles and the Environment () 1 Informal document GRPE-74-30 76 th GRPE, 11-12 January 2018 Agenda item 9 REPORT TO GRPE 76 TH SESSION Current Mandate
More information18642, INSTALLATION INSTRUCTIONS
18642, 18643 INSTALLATION INSTRUCTIONS WARNING! The fuel system is under pressure. Do not open the fuel system until the pressure has been relieved. Refer to the appropriate vehicle service manual for
More informationRotating Vane Anemometer
Ventilation Testing Rotating Vane Anemometer Alnor Model RVA801 AIRFLOW Model LCA301 Operation and Service Manual Copyright TSI Incorporated / 2007-2012 / All rights reserved. Address TSI Incorporated
More informationProduct Development and Testing An AMCA Registered Laboratory LJ Airflow: Static Pressure: Temperature: To 80,000 CFM To 50" wg To 600 F Bradner Ohio Test Facility Floor Plan I Approved to conduct performance
More informationA / B / Lobby: L: 1.5m 2 high-level wall vent Stair: Top and bottom vent R: 1.5m 2 high-level wall vent Mean temp in occupied space = 134 C
Smoke Ventilation of Common Access Areas of Flats and Maisonettes (BD2410) - Final Factual Report Appendix Div ( Lobby scenario visibilities with 2.5 MW fire and 0.78 m dwelling & stair door openings)
More information18673, INSTALLATION INSTRUCTIONS
18673, 18674 INSTALLATION INSTRUCTIONS WARNING! The fuel system is under pressure. Do not open the fuel system until the pressure has been relieved. Refer to the appropriate vehicle service manual for
More informationHARFORD SAFELOCK MECHANICAL QUICK HITCH
HARFORD SAFELOCK MECHANICAL QUICK HITCH Installation & Operation Manual Important: This manual must be kept with the excavator at all times and referred to as required Harford Attachments Ltd Table of
More informationA MODEL SYLLABUS FOR THE TRAINING OF TECHNICIANS INVOLVED IN THE EXAMINATION, TESTING, MAINTENANCE AND REPAIR OF PETROLEUM ROAD TANKERS
A MODEL SYLLABUS FOR THE TRAINING OF TECHNICIANS INVOLVED IN THE EXAMINATION, TESTING, MAINTENANCE AND REPAIR OF PETROLEUM ROAD TANKERS A MODEL SYLLABUS FOR THE TRAINING OF TECHNICIANS INVOLVED IN THE
More informationIndoor Air Quality Meter
Indoor Air Quality Indoor Air Quality Meter Alnor Model CF910 AIRFLOW TM Model IAQ910 Operation and Service Manual Copyright TSI Incorporated / 2007-2008 / All rights reserved. Address TSI Incorporated
More informationAir Excellent semi-circular semi-rigid ductwork. Technical data
Air Excellent semi-circular semi-rigid ductwork Technical data TABLE OF CONTENTS 1 INTRODUCTION... 3 2 SYSTEM OVERVIEW... 3 3 MATERIALS... 4 4 SEMI-CIRCULAR (SC) DUCTWORK... 5 4.1 AIR VELOCITY (m/s vs
More informationACCESS DOORS GENERAL PRODUCT OVERVIEW
GENERAL PRODUCT OVERVEW Fire dampers need inspecting and testing, coils need cleaning and controls need adjusting. Nailor ndustries offers a range of duct and plenum access doors that have been designed
More informationDIGIGAUGE P R E S S U R E D I S P L A Y S Y S T E M I N S T R U C T I O N M A N U A L
DIGIGAUGE P R E S S U R E D I S P L A Y S Y S T E M I N S T R U C T I O N M A N U A L Thank you for purchasing DigiGauge by ZAETECH Disclaimer DigiGauge is for show and off road use only. By using this
More informationConstant Airflow Regulators & Registers
Constant Airflow Regulators & Registers The Simple Solution The model CAR-II Constant Airflow Regulator is a modulating orifice that automatically regulates airflows in duct systems to constant levels.
More informationTest Report No.: SDHL FT Date: Jun.15, 2017 Page 1 of 5
Test Report No.: SDHL1705010441FT Date: Jun.15, 2017 Page 1 of 5 SHENGZHAO FURNITURE FACTORY LIANGYONG INDUSTRIAL ZONE, ZHENNAN JIUJIANG TOWN, FOSHAN CITY, GUANGDONG PROVINCE, CHINA The following sample(s)
More informationEXHAUST FAN FLOW METER
EXHAUST FAN FLOW METER OVERVIEW AND MANUAL THE ENERGY CONSERVATORY WARRANTY EXPRESS LIMITED WARRANTY Seller warrants that this product, under normal use and service as described in the operator s manual,
More informationseries FSD-FLD Fire and smoke dampers UL Approval
series FSD-FLD Fire and smoke dampers UL Approval www.koolair.com Series FSD-FLD 1 Fire and smoke dampers UL Approval FSD-B-U / FSD-A-U and FLD-S-U / FLD-S-UD CONTENTS Description FSD-B-U / FSD-A-U 2 Construction
More informationTest Report For: EMECO INDUSTRIES INC Bar Stool
4700 Broadmoor SE, Suite 200 Kentwood, MI 49512 Telephone: 616-- 656-- 7401 Facsimile: 616-- 656-- 2022 www.intertek-- etlsemko.com EMECO INDUSTRIES INC P.O. No. N / A Page 1 of 18 Test Report For: EMECO
More information30-Aug-11. VCA job number: CSM Date: 30 August Dear Sirs,
VCA job number: CSM241075 Date: 30 August 2011 Dear Sirs, 1. The vehicle type / component described on the attached approval(s) has been tested and meets the requirements of the ECE Regulation / EEC Directive
More informationSmart Grid Subcommittee Report
Smart Grid Subcommittee Report Marilyn Brown Subcommittee Vice-Chair U.S. Department of Electricity Electricity Advisory Committee February 20, 2018 Subcommittee Overview Statutory basis: The Energy Independence
More information= CASE STUDY = RIYADH HILTON MAINTAINS TIGHT SCHEDULE AND PASSES INSPECTION WITH THE HELP OF AEROSEAL DUCT SEALING
Media Contact: Brad Brenner (503) 736-0610 brad@brennerassociates.com = CASE STUDY = RIYADH HILTON MAINTAINS TIGHT SCHEDULE AND PASSES INSPECTION WITH THE HELP OF AEROSEAL DUCT SEALING Project Achieves
More informationIAQ-CALC INDOOR AIR QUALITY METER MODEL 7515
IAQ-CALC INDOOR AIR QUALITY METER MODEL 7515 OPERATION AND SERVICE MANUAL P/N 1980571, REVISION D FEBRUARY 2016 Copyright TSI Incorporated / May 2007-2016 / All rights reserved. Address TSI Incorporated
More informationHigh Performance Axial Fans
High Performance Axial Fans Model RA Standard and High Temperature High Efficiencies Low Sound January 2014 High Performance Axial Fans Greenheck s model RA, high performance, direct-driven axial fans,
More informationSTANDBY EMERGENCY CNG/LPG GENERATOR
SECTION 16620 STANDBY EMERGENCY CNG/LPG GENERATOR PART 1 GENERAL 1.01 SUMMARY A. Section Includes: Compressed natural gas (CNG) or liquefied petroleum gas (LPG) powered standby emergency generators. B.
More informationtesto Smart Probes The SMART world of Testo HVAC
testo Smart Probes The SMART world of Testo HVAC My world just got a whole lot EASIER The most exciting development in HVAC Instruments. EVER. The biggest family of SMART instruments. Servicing heating
More informationWP2 - CFD Private Network Meter Commissioning, Proving and Calibration Tests
WP2 - CFD Private Network Meter Commissioning, Proving and Calibration Tests EMRS Working Practice Public Version: 2.0 Date: 13 October 2017 Table of Contents Change Amendment Record 3 1. Introduction
More informationAEROMOTIVE Part # C5 Corvette Fuel Rail Kit INSTALLATION INSTRUCTIONS
AEROMOTIVE Part # 14128 99-04 C5 Corvette Fuel Rail Kit INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems and repair procedures. We recommend
More informationTEST REPORT INTERTEK TESTING SERVICES NA, INC Arlingate Lane Columbus, OH, 43228
TEST REPORT INTERTEK TESTING SERVICES NA, INC. 1717 Arlingate Lane Columbus, OH, 43228 PROJECT NO.: G101483861 ISSUE DATE: February 21, 2014 INTERIM REPORT NO. 101483861COL-001B RENDERED TO Client: TSI
More informationof Fire Pump Assemblies
A.1.0 A.1.1 A.2.0 A.2.1 A.2.2 A.2.3 A.2.4 A.2.5 A.2.6 A.3.0 A.3.1 A.4.0 A.4.1 Report of Inspection, Testing & Maintenance System in service before conducting tasks Pertinent parties notified before conducting
More informationINSTRUCTION MANUAL. HEATED FILTER PROBES GENERAL PURPOSE SERIES Model 33C. Version Perma Pure LLC Tel:
PERMA PURE INSTRUCTION MANUAL HEATED FILTER PROBES GENERAL PURPOSE SERIES Model 33C Version 4.04 Perma Pure LLC Tel: 732-244-0010 P.O. Box 2105, 8 Executive Drive Tel: 800-337-3762 (toll free US) Toms
More informationENERGY EFFICIENCY NATIONAL BUILDING REGULATIONS. Development Management Department 1 of 49
ENERGY EFFICIENCY NATIONAL BUILDING REGULATIONS 1 of 49 BACKGROUND 2 of 49 National Energy Efficiency Strategy of the Republic of South Africa March 2005 ( Reviewed 2008 / 2011 ) 3 of 49 OBJECTIVES Develop
More informationBEFORE THE PUBLIC UTILITIES COMMISSION OF THE STATE OF CALIFORNIA
BEFORE THE PUBLIC UTILITIES COMMISSION OF THE STATE OF CALIFORNIA Order Instituting Rulemaking to Consider Smart Grid Technologies Pursuant to Federal Legislation and on the Commission s own Motion to
More informationNORDFAB DUCTING CATALOGUE
NORDFAB DUCTING CATALOGUE C l i p p e d D u c t i n g THE WORLD S FASTEST DUCTING & FLANGED DUCTWORK Nordfab QF Clipped and FL Flanged ducting QF clipped and FL flanged ducting offers a complete range
More informationR-317 Air Flow Controller
24-4660- 1, Rev. B Product Bulletin R-317 Issue Date February 2016 R-317 Air Flow Controller The R-317 Air Flow Controller is a proportional, direct acting, low volume output signal instrument designed
More informationSINGLE DUCT TERMINAL UNITS
www.igcaire.com SINGLE DUCT TERMINAL UNITS Direct Digital Control, Pressure Independent FEATURES 22 Gauge Galvanized Steel Casing Construction with a 20 Gauge Casing Option that Provides Strength and Product
More informationHOTCHKISS AIR ACOUSTICS
HOTCHKISS AIR ACOUSTICS C 3 & C 4 C I R C U L A R A T T E N U A T O R S Description Hotchkiss Air Acoustic type C3 & C4 Circular attenuators are available in all standard circular fan sizes from 315mm
More informationUL/cUL FILE NUMBER E CE See last page of manual for CE Declaration of Conformity.
INSTALLATION, OPERATION and MAINTENANCE MANUAL MODEL SCPF1 15, 25, 40 & 65 AMP SCR POWER CONTROLS UL/cUL FILE NUMBER E151547 CE See last page of manual for CE Declaration of Conformity. AMETEK HDR POWER
More informationSpeeding. Standard Operating Procedure
Speeding Standard Operating Procedure Notice: This document has been made available through the Police Service of Scotland Freedom of Information Publication Scheme. It should not be utilised as guidance
More informationEMI / RFI Shielding Products. Shielding Honeycomb Ventilation Panels and Dust Filtration Characteristics
P.O. Box 699 17540 State Highway 198 Saegertown, PA 16433 EMI / RFI Shielding Products Phone: 877-MAJR PRO 814-763-3211 Fax: 814-763-2952 E-Mail: sales@majr.com Shielding Honeycomb Ventilation Panels and
More information2016 Product Training
2016 Product Training Course 1: City Multi VRF DESIGN This course is designed for consulting engineers, specifiers, installation contracting engineers, and sales engineers who require detailed knowledge
More informationNational Grid UK Electricity Transmission plc. NATIONAL SAFETY INSTRUCTION and Guidance
National Grid UK Electricity Transmission plc NATIONAL SAFETY INSTRUCTION and HIGH VOLTAGE METAL CLAD SWITCHGEAR WITH SPOUTS Copyright National Grid plc 2014, all rights reserved. No part of this publication
More informationIAQ-CALC TM Indoor Air Quality Meter
ENERGY AND COMFORT Indoor Air Quality IAQ-CALC TM Indoor Air Quality Meter Model 7515 Operation and Service Manual Copyright TSI Incorporated / May 2007 / All rights reserved. Address TSI Incorporated
More information11-Feb-14. VCA job number: CSP Date: 11 February Dear Sirs,
VCA job number: CSP286503 Date: 11 February 2014 Dear Sirs, 1. The vehicle type / component described on the attached approval(s) has been tested and meets the requirements of the ECE Regulation / EEC
More informationElectric Vehicles and the Environment (EVE IWG)
Submitted by the EVE informal working group Electric Vehicles and the Environment () 1 Informal document GRPE-77-28 77 th GRPE, 6-8 June 2018 Agenda item 9 REPORT TO GRPE 77 TH SESSION Current Mandate
More informationTanks: Informal Working Group on the inspection and certification of tanks
Economic Commission for Europe Inland Transport Committee Working Party on the Transport of Dangerous Goods Joint Meeting of the RID Committee of Experts and the Working Party on the Transport of Dangerous
More informationAEROMOTIVE Part # L 4V Fuel Rails INSTALLATION INSTRUCTIONS
AEROMOTIVE Part # 14130 5.0L 4V Fuel Rails INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems and repair procedures. We recommend that this
More information8" - 12" Hydraulic Steel Squeeze Off Tool
8" - 12" Hydraulic Steel Squeeze Off Tool ECN 19130 C812S Hydraulic Steel Squeeze Off Tool for Steel Pipe Page 1 of 8 This Footage Tools C812S Steel Squeeze Off Tool is sold with one pump configuration
More informationVC Series. Volume Control Dampers M A N U F A C T U R E R S O F A I R, F I R E A N D S M O K E C O N T R O L P R O D U C T S
V41706 VC Series Volume Control Dampers Roll formed steel blades with three material options DW144 compliant Flanged models with 65mm deep mechanically fixed casings Rectangular spigotted models with 85mm
More informationVolume Control Dampers. Series LF upvc-vcd High performance plastic volume control dampers. Incorporating
Volume Control Dampers Incorporating Series LF upvc-vcd 2.76 m 3 /hr/m 2 leakage at 50 Pa, over 70% better than required by Part L of Building Regulations Corrosion resistant, perfect for chlorinated atmospheres
More informationVentilation Testing. Micromanometer. Alnor Model AXD610 AIRFLOW TM Model PVM610. Operation and Service Manual
Ventilation Testing Micromanometer Alnor Model AXD610 AIRFLOW TM Model PVM610 Operation and Service Manual Copyright TSI Incorporated / 2007-2008 / All rights reserved. Address TSI Incorporated / 500 Cardigan
More informationTECHNICAL SPECIFICATIONS FOR STEEL PLATES
TECHNICAL SPECIFICATIONS FOR STEEL PLATES 1.0 SCOPE: HINDUSTAN PETROLEUM CORPORATION LTD., GRESHAM HOUSE This specification covers requirement for Carbon Steel Plates of Structural Quality as per IS: 2062
More informationONE TOUCH FITTINGS Series WP2
ONE TOUCH FITTINGS - M5 1/ 1/ 3/ 1/2 Features Attractive design Compact size ed nipples of L, T & Y fittings enable plastic portion to turn by 30º Full area of the inner bore of the tubing is available
More informationIGNITION INTERLOCK SERVICE CENTER RENEWAL LICENSE
TRAFFIC SAFETY DIVISION APPLICATION FOR IGNITION INTERLOCK SERVICE CENTER RENEWAL LICENSE INSTRUCTIONS FOR COMPLETING THIS APPLICATION PLEASE: complete this application on your computer using the TAB key
More informationSHEYENNE TELE-BOOM OWNERS MANUAL OPERATOR INSTRUCTIONS PARTS BOOK
SHEYENNE TELE-BOOM OWNERS MANUAL OPERATOR INSTRUCTIONS PARTS BOOK 701 Lenham Ave. SW PO Box 647 Cooperstown ND 58425 1-800-797-1883 701-797-2700 * 701-797-2584 Fax www.sheyennemfg.com TABLE OF CONTENTS
More informationIrisControlDamper. For Adjustment and Measuring of Airflow.
IrisControlDamper For Adjustment and Measuring of Airflow www.actionair.co.uk sales@actionair.co.uk Iris Control Damper (ICD) Quick, silent and efficient is the simple summary of the features of the Actionair
More information08-Dec-10. VCA job number: CSL Date: 08 December Dear Sirs,
VCA job number: CSL225489 Date: 08 December 2010 Dear Sirs, 1. The vehicle type / component described on the attached approval(s) has been tested and meets the requirements of the ECE Regulation / EEC
More informationPROPOSED BROILER FARMS
PROPOSED BROILER FARMS BARINGHUP WEST Traffic Engineering Assessment Prepared for PAVILION PARTNERS MARCH, 2014 OUR REFERENCE: 16853R9457 PROPOSED BROILER FARMS BARINGHUP WEST Traffic Engineering Assessment
More informationSEM.Test Compliance Service Co., Ltd
TEST REORT ST/SG/AC.10/11 Rev.5 Section 38.3 AMEDMETS TO THE FIFTH REVISED EDITIO OF THE RECOMMEDATIOS O THE TRASORT OF DAGEROUS GOODS, MAUAL OF TEST AD CRITERIA (Section 38.3: Lithium batteries) Report
More informationFRONTIER PITTS MAINTENANCE CONTRACTS
FRONTIER PITTS MAINTENANCE CONTRACTS FRONTIER PITTS Frontier Pitts has over 90 years experience in the design, manufacture, and installation of perimeter security equipment, which makes us the very best
More informationNCC Leisure Battery Verification Scheme. Leisure Accommodation Vehicles
The UK trade body for the caravan, motorhome, caravan holiday and park home industry. NCC Leisure Battery Verification Scheme Leisure Accommodation Vehicles Page 1 of 11 1 Scope The NCC Battery Verification
More informationDriving at Work Policy September 2016
Driving at Work Policy September 2016 Signed by the Chair of the Management Board.. Review Date: September 2018 CONTENTS 1. PURPOSE 2. DEFINITION 3. POLICY STATEMENT 4. RISK ASSESSMENT 5. PROCEDURES 6.
More informationAll European member states were given until 26th September 2008 to transpose the detail of the Directive into each member s local legislation.
THE UK WASTE BATTERIES REGULATIONS BACKGROUND AND INTRODUCTION On 6th September 2006 the European Parliament passed Directive 2006/66/EC on batteries and accumulators and waste batteries and accumulators.
More informationTechnical Information
Subject MARPOL Annex IV Approval of Discharge Rate of Untreated Sewage from Sewage Holding Tank To whom it may concern Technical Information No. TEC-0758 Date 12 December 2008 According to Regulation 11
More information7.3L POWERSTROKE BANJO BOLT KIT Fits L Powerstroke Diesel. Installation Guide
7.3L POWERSTROKE BANJO BOLT KIT Fits 94-03 7.3L Powerstroke Diesel Installation Guide INSPECT CONTENTS OF THIS KIT THOROUGHLY BEFORE STARTING THE INSTALLATION PROCESS! IF YOU FIND A PROBLEM WITH YOUR PACKAGE:
More information