Air Excellent semi-circular semi-rigid ductwork. Technical data
|
|
|
- Giles Harris
- 5 years ago
- Views:
Transcription
1 Air Excellent semi-circular semi-rigid ductwork Technical data
2 TABLE OF CONTENTS 1 INTRODUCTION SYSTEM OVERVIEW MATERIALS SEMI-CIRCULAR (SC) DUCTWORK AIR VELOCITY (m/s vs m3/h) PRESSURE LOSS (Pa/m) SYSTEM COMPONENTS SEMI-CIRCULAR (SC) DUCT DISTRIBUTION BOXES DBOX CONFIGURATIONS SUPPLY & EXTRACT VALVES AND FLOOR GRILLES CERTIFICATION...17 Page 2 18 Ubbink Air Excellent semi-circular semi-rigid ductwork
3 1 INTRODUCTION The Air Excellent air distribution system is a radial air distribution system, which uses semi-rigid ductwork to distribute air for central mechanical ventilation systems with heat recovery in domestic and small commercial buildings. The system has several components, including semi-rigid duct and accessories, including rigid 90 horizontal and vertical bends, valve adaptors and supply and extract valves. The ventilation unit is connected to the distribution boxes using insulated mass flow ducts and sound attenuators and the semi-rigid duct is rolled out to supply fresh air to the habitable rooms and extract stale, moist from the wet rooms. A range of accessories make it possible to make air tight connections without using tapes or adhesives, fix the semi-rigid duct to the floor, suspend it from ceilings, make shallow bends around obstacles and make sharp horizontal and vertical bends if required. The air flow rate in each duct run is determined by air flow restrictors in the distribution box and Ubbink supplies a free commissioning tool which can be used to determine how many rings to cut out of the air flow restrictors. The commissioning tool requires the following information: semi-rigid duct type, lengths of the ducts runs, number and type of bends (horizontal or vertical). USP s: Low(er) pressure loss than traditional systems due to radial design Mechanical connections = consistent quality and long-term air-tightness Installation: A plastic duct on a roll is easy and quick to cut to length and bend around obstacles Mechanical connections (i.e. no duct tape) means quick, clean and consistent quality of installation Quick, quality and consistent commissioning using the configuration tool and air flow restrictor rings Easy and quick maintenance Low duct height for in-wall and/or screed floor application Anti-static and anti-bacterial properties (if required) 2 SYSTEM OVERVIEW Page 3 18 Ubbink Air Excellent semi-circular semi-rigid ductwork
4 3 MATERIALS SEMI-CIRCULAR SEMI-RIGID DUCT PE outer and smooth PE inner layer Semi-circular cross-section ACCESSORIES PP with anti-static and anti-bacterial properties SEAL RINGS TPE and PP 2-component-injection-moulding Page 4 18 Ubbink Air Excellent semi-circular semi-rigid ductwork
5 Qv [m 3 /h] 4 SEMI-CIRCULAR (SC) DUCTWORK 4.1 AIR VELOCITY (m/s vs m3/h) AIR VELOCITY DUCT TYPE(S) V [m/s] 2,5 3,0 3,5 4, Page 5 18 Ubbink Air Excellent semi-circular semi-rigid ductwork
6 4.2 PRESSURE LOSS (Pa/m) Page 6 18 Ubbink Air Excellent semi-circular semi-rigid ductwork
![4.3 SYSTEM COMPONENTS SEMI-CIRCULAR (SC) DUCT SEMI-RIGID DUCT Duct AE35 AE55 type Code 51603102 51603140 (20m) (30m) A [mm] 50 60 B [mm] 102 132 10 m 3](/docs-images/86/94726364/images/7-1.jpg "/h 0,3 0,1 20 m 3 /h 12 0,3 30 m 3 /h 2,8 0,7 40 m 3 /h 4,9 1,2 50 m 3 /h 7,7 1,8 60 m 3 /h 11,1 2,6 Duct AE35 AE55 type r 1 [mm] >200 >400 r 2 [mm]")
![>150 >200 H [mm] 50 60 Zeta [-] 0,24 (r=200 ) 0,60 (r=150) 0,55 (r=400) 0,50 (r=200) 10 m 3 /h 0,1 0,3 0,0 0,0 20 m 3 /h 0,5 1,2 0,1 0,1 30 m 3 /h 1,1](/docs-images/86/94726364/images/7-2.jpg "2,6 0,4 0,3 40 m 3 /h 1,9 4,7 0,8 0,7 50 m 3 /h 2,9 7,3 1,4 1,3 60 m 3 /h 4,2 10,6 2,2 2,0 Page 7 18 Ubbink Air Excellent semi-circular semi-rigid")
7 4.3 SYSTEM COMPONENTS SEMI-CIRCULAR (SC) DUCT SEMI-RIGID DUCT Duct AE35 AE55 type Code (20m) (30m) A [mm] B [mm] m 3 /h 0,3 0,1 20 m 3 /h 12 0,3 30 m 3 /h 2,8 0,7 40 m 3 /h 4,9 1,2 50 m 3 /h 7,7 1,8 60 m 3 /h 11,1 2,6 Duct AE35 AE55 type r 1 [mm] >200 >400 r 2 [mm] >150 >200 H [mm] Zeta [-] 0,24 (r=200 ) 0,60 (r=150) 0,55 (r=400) 0,50 (r=200) 10 m 3 /h 0,1 0,3 0,0 0,0 20 m 3 /h 0,5 1,2 0,1 0,1 30 m 3 /h 1,1 2,6 0,4 0,3 40 m 3 /h 1,9 4,7 0,8 0,7 50 m 3 /h 2,9 7,3 1,4 1,3 60 m 3 /h 4,2 10,6 2,2 2,0 Page 7 18 Ubbink Air Excellent semi-circular semi-rigid ductwork
![HORIZONTAL BEND Duct AE35sc AE55sc type Code 188304 188154 A [mm] 204](/docs-images/86/94726364/images/8-0.jpg "164 B [mm] 204 164 r [mm] 63 75 Zeta [-] 0,23 0,75 Q v [m 3 /h] 10 0,1")
![118 149 r [mm] 37 39 Zeta [-] 0,55 0,68 Q v [m 3 /h] 10 0,3 0,1 20 1,1](/docs-images/86/94726364/images/8-2.jpg "0,4 30 2,5 1,0 40 4,4 1,7 50 6,9 2,7 60 9,9 3,9 STRAIGHT CONNECTOR")
![Duct type AE35sc AE55sc Code 188306 188306 A [mm] 118 148 B [mm] 61 71](/docs-images/86/94726364/images/8-4.jpg "Zeta [-] 0 0 Page 8 18 Ubbink Air Excellent semi-circular semi-rigid")
8 HORIZONTAL BEND Duct AE35sc AE55sc type Code A [mm] B [mm] r [mm] Zeta [-] 0,23 0,75 Q v [m 3 /h] 10 0,1 0,1 20 0,5 0,5 30 1,0 1,1 40 1,8 1,9 50 2,9 3,0 60 4,1 4,3 VERTICAL BEND Duct AE35sc AE55sc type Code A [mm] B [mm] r [mm] Zeta [-] 0,55 0,68 Q v [m 3 /h] 10 0,3 0,1 20 1,1 0,4 30 2,5 1,0 40 4,4 1,7 50 6,9 2,7 60 9,9 3,9 STRAIGHT CONNECTOR Duct type AE35sc AE55sc Code A [mm] B [mm] Zeta [-] 0 0 Page 8 18 Ubbink Air Excellent semi-circular semi-rigid ductwork
9 AE35 SC VALVE ADAPTOR mm Duct AE35sc type Code A [mm] 301 B [mm] Min. 100 mm C [mm] DN125 Zeta [-] 1,08 0,84 1,29 1,52 Q v [m 3 /h] 1 x 10 0,5 0,6 2 x 5 0,1 0,2 1 x 20 2,2 2,6 2 x 10 0,4 0,8 1 x 30 4,9 5,8 2 x 15 0,9 1,7 1 x 40 8,7 10,4 2 x 20 1,7 3,1 1 x 50 13,6 16,2 2 x 25 2,6 4,8 1 x 60 19,5 23,3 2 x 30 3,8 6,9 AE55 SC VALVE ADAPTOR mm Duct AE55sc type Code A [mm] 388 B [mm] Min. 100 mm C [mm] DN125 Zeta [-] 1,59 1,81 1,98 3,03 Q v [m 3 /h] 1 x 10 0,3 0,3 2 x 5 0,1 0,1 1 x 20 1,0 1,3 2 x 10 0,3 0,5 1 x 30 2,3 2,8 2 x 15 0,6 1,1 1 x 40 4,0 5,0 2 x 20 1,1 1,9 1 x 50 6,3 7,8 2 x 25 1,8 3,0 1 x 60 9,1 11,3 2 x 30 2,6 4,3 Page 9 18 Ubbink Air Excellent semi-circular semi-rigid ductwork
![AE55 SC VALVE ADAPTOR 180 125mm Duct type AE55sc Code 188164 A [mm] 402 B [mm] Min.](/docs-images/86/94726364/images/10-1.jpg "100 mm C [mm] DN125 Zeta [-] 1,97 1,25 1,66 2,57 Q v [m 3 /h] 1 x 10 0,3 0,3 2 x 5 0,0")
10 AE55 SC VALVE ADAPTOR mm Duct type AE55sc Code A [mm] 402 B [mm] Min. 100 mm C [mm] DN125 Zeta [-] 1,97 1,25 1,66 2,57 Q v [m 3 /h] 1 x 10 0,3 0,3 2 x 5 0,0 0,1 1 x 20 1,3 1,1 2 x 10 0,2 0,4 1 x 30 2,8 2,4 2 x 15 0,4 0,9 1 x 40 5,0 4,2 2 x 20 0,8 1,6 1 x 50 7,8 6,6 2 x 25 1,2 2,5 1 x 60 11,1 9,5 2 x 30 1,8 3,7 SEAL RING The seal ring is a vital component of the system and ensures airtight and sustainable connections. The seal ring must be used to make all connections in the system. Codes: AE35sc (4 pcs/box) / AE55sc (4 pcs/box) MOUNTING CLIP Codes: AE35sc (10 pcs/box) / AE55sc (10 pcs/box) Page Ubbink Air Excellent semi-circular semi-rigid ductwork
![FLOOR GRILLE 90 ADAPTOR Duct type AE35sc AE55sc Code 188308 188158 A [mm] 285 mm B [mm] Min.](/docs-images/86/94726364/images/11-2.jpg "80 mm C [mm] 309x86 mm Zeta [-] 0,84 (1,25) 0,64 (2,39) 0,78 (2,23) Q v [m 3 /h] 1 x 10 0,4 (0,6) 0,1 (0,4) 2 x 5 0,1 (0,3) 1 x 20 1,7 (2,5)")
11 FLOOR GRILLE 90 ADAPTOR Duct type AE35sc AE55sc Code A [mm] 285 mm B [mm] Min. 80 mm C [mm] 309x86 mm Zeta [-] 0,84 (1,25) 0,64 (2,39) 0,78 (2,23) Q v [m 3 /h] 1 x 10 0,4 (0,6) 0,1 (0,4) 2 x 5 0,1 (0,3) 1 x 20 1,7 (2,5) 0,5 (1,4) 2 x 10 0,3 (1,2) 1 x 30 3,8 (5,6) 1,1 (3,2) 2 x 15 0,7 (2,7) 1 x 40 6,7 (10,0) 2,0 (5,7) 2 x 20 1,3 (4,8) 1 x 50 10,5 (15,7) 3,1 (8,8) 2 x 25 2,0 2,0 (7,5) 1 x 60 15,2 (22,6) 4,5 (12,7) 2 x 30 2,9 (10,8) NB The zeta values between brackets include a grille. Page Ubbink Air Excellent semi-circular semi-rigid ductwork
12 FLOW RESTRICTORS No. of rings removed AE35sc Zeta [-] 19,32 5,18 1,52 0,45 0,23 Q v [m 3 /h] 10 9,7 2,6 0,8 0,2 0, ,7 10,4 3,0 0,9 0, ,2 23,4 6,9 2,0 1, ,9 41,5 12,2 3,6 1, ,1 64,9 19,0 5,6 2, ,6 93,5 27,4 8,1 4,2 AE55sc Zeta [-] 36,80 7,10 2,30 0,60 0,10 Q v [m 3 /h] 10 5,8 1,1 0,4 0,1 0, ,3 4,5 1,5 0,4 0, ,5 10,1 3,3 0,9 0, ,3 18,0 5,8 1,5 0, ,8 28,1 9,1 2,4 0, ,9 40,5 13,1 3,4 0,6 NB A flow restrictor is used to ensure that the correct flow rate is achieved in each duct run. The flow restrictor has 4 rings which can be cut out using a knife. The number of rings to be removed can be determined by the Ubbink configuration tool. The flow restrictor is placed in the sealing ring of the associated duct before it is attached to the distribution box. Page Ubbink Air Excellent semi-circular semi-rigid ductwork
13 5 DISTRIBUTION BOXES STANDARD AE35 AE55 A B C D E F sc sc 1 5x x x x 2x x 3x x x FLAT AE35 AE55 A B C D E F sc sc 1 8x 2x x 2x Coming soon x 4x x 2x Page Ubbink Air Excellent semi-circular semi-rigid ductwork
14 5.1 DBOX CONFIGURATIONS DBOX CONFIGURATIONS Installation with mass flow duct downwards Installation with mass flow duct upwards Installation without mass flow duct Page Ubbink Air Excellent semi-circular semi-rigid ductwork
15 6 SUPPLY & EXTRACT VALVES AND FLOOR GRILLES SUPPLY VALVE 125mm Duct type AE23C / AE34C / AE48C / AE35SC / AE55SC Code A [mm] 125 B [mm] 40 C [mm] 46 D [mm] 155 Page Ubbink Air Excellent semi-circular semi-rigid ductwork
![AE34c / AE48c / AE35sc / AE55sc Code 188317 (Inox), 188316 (White) A [mm] 296 B [mm]](/docs-images/86/94726364/images/16-4.jpg "350 C [mm] 80 D [mm] 130 Page 16 18 Ubbink Air Excellent semi-circular semi-rigid")
16 EXTRACT VALVE 125mm Duct type AE23C / AE34C / AE48C / AE35SC / AE55SC Code A [mm] 125 B [mm] 45 C [mm] 31 D [mm]] 150 E [mm] 100 FLOOR GRILLE Duct type AE23c / AE34c / AE48c / AE35sc / AE55sc Code (Inox), (White) A [mm] 296 B [mm] 350 C [mm] 80 D [mm] 130 Page Ubbink Air Excellent semi-circular semi-rigid ductwork
17 7 CERTIFICATION Page Ubbink Air Excellent semi-circular semi-rigid ductwork
18 UBBINK CENTROTHERM GROUP Designs and specifications are subject to change without notice August 2013, Version 4 Ubbink Centrotherm Group The Netherlands - Ubbink BV, Phone: , United Kingdom - Ubbink UK Ltd, Phone , France - Ubbink France S.A.S., Phone , Belgium - Ubbink NV, Phone: , Italy - Centrotherm Gas Flue Technologies Italia SRL, Phone , Page Ubbink Air Excellent semi-circular semi-rigid ductwork
Flexible Ducts. Producent zastrzega sobie prawo do dokonywania zmian w wymiarach i danych technicznych produktów ze względu na ciągłe ich doskonalenie
Flexible Ducts Producent zastrzega sobie prawo do dokonywania zmian w wymiarach i danych technicznych produktów ze względu na ciągłe ich doskonalenie About the System About the System The flexible ducts
Incorporating V2.0. Product spec >>> > Series DJ - Drum jet diffusers
Incorporating V2.0 Product spec >>> > Series DJ - Drum jet diffusers Diffusers Drum jets (Premium) Recommended for: Wall, ceiling & duct Supply Overview Exceptional throw Throw completely adjustable Drum
SEMI RIGID THE PROFESSIONALS CHOICE
SEMI RIGID THE PROFESSIONALS CHOICE for efficient, high performance MVHR ductwork installations. SAP APPENDIX Q LISTED brookvent.co.uk FITTING OUTLINE THE PROFESSIONALS CHOICE for efficient, high performance
Ver NEW MVHR DUCTING SYSTEM
Ver. 4.1 NEW MVHR DUCTING SYSTEM CONTENTS SERIES...04 1 SERIES...07 SERIES... SERIES...14 DUCT & JOINT INTRODUCTION The range is a ducting system specifically designed for the residential and small commercial
DFB - Conical Ceiling Diffuser. Halton DFB. Conical Ceiling Diffuser
Halton DFB Conical Ceiling Diffuser Horizontal air supply, suitable also for exhaust Installation flush to the ceiling, light-weight aluminium design Circular duct connection with rubber gasket All sizes
www.imaginairbygrada.com Architectural residential air valve with limitless customisation possibilities for new buildings or renovation EN 1751 CLASS HIGH-PERFORMANCE CEILING / WALL AIRTIGHT SEAL CUSTOM
C O L M A N. Air Distribution JET DIFFUSERS DCJ SERIES DCJ SERIES
C O L M A N Air Distribution E N G I N E E R E D A I R P R O D U C T S JET DIFFUSERS DCJ SERIES DCJ SERIES DCJ SERIES JET DIFFUSERS Application Colman s DCJ jet diffuser has been designed to supply cooled
TCM - Conical Ceiling Diffuser. Halton TCM. Conical Ceiling Diffuser
Halton TCM Conical Ceiling Diffuser Horizontal air supply, suitable also for exhaust Suitable for cooling applications with supply/room air temperature difference as low as -12 C Installation flush to
Disc valves. Type Z-LVS. For supply air. 03/2017 DE/en PD Z-LVS 1
X X testregistrierung Disc valves Type For supply air Circular disc valves with manually adjustable annular gap Nominal sizes 100, 125, 160, 200 mm Volume flow rate range 10 90 l/s or 36 324 m³/h Diffuser
Type DCS FOR HORIZONTAL SWIRLING SUPPLY AIR DISCHARGE CREATING HIGH INDUCTION LEVELS, WITH FIXED AIR CONTROL BLADES
Homepage > Products > Grilles and Diffusers > Ceiling diffusers > Ceiling swirl diffusers with perforated face plate > Type DCS Type DCS FOR HORIZONTAL SWIRLING SUPPLY AIR DISCHARGE CREATING HIGH INDUCTION
NEW. PLASTIC MODULAR CHAIN WT0705-W Plastic Top Chain
NEW PLASTIC MODULAR CHAIN WT0705-W Plastic Top Chain A new 7.5 mm-pitch chain has been added to our lineup of plastic modular chains. Features of WT0705-W Plastic Modular Chain Knife-edge conveyor applications
Climate Recovery Duct System Technical Specifications
Climate Recovery Duct System Technical Specifications Climate Recovery (CR) Duct System Climate Recovery (CR) Duct System Overview The CR Duct System offers a complete, pre-insulated system for heating,
Flexible ducting system FlexPipe plus Round 75 mm Ø in combination with Oval 51 x 114 mm
Flexible ducting system FlexPipe plus FlexPipe plus round and oval ducting system. Arbitrarily combinable. FlexPipe plus is the further development of the successful air distribution system FlexPipe and
ULTRA LOW ENERGY. VHR Void Series W/I/s TOTAL SFP Typical. Made in the UK. VHR Void Mounted Heat Recovery Units VHR PERFORMANCE OVERVIEW:
VHR Void Mounted Heat Recovery Units TM.72 W/I/s TOTAL SFP Typical General: Units shall be manufactured from high quality galvanized sheet steel with stainless steel drain trays, acoustic, non-hygroscopic
Grilles & Diffusers. Series NV Non-vision grilles. Incorporating. Sight blocking design ensures privacy is maintained
Grilles & Diffusers Incorporating Series NV Sight blocking design ensures privacy is maintained Perfect for areas like changing rooms Four models available including units to suit door mounting and dark
DFA - Conical Ceiling Diffuser. Halton DFA. Conical Ceiling Diffuser
Halton DFA Conical Ceiling Diffuser Horizontal air supply, suitable also for exhaust Installation flush to the ceiling, light-weight aluminium design Circular duct connection with rubber gasket Openable
THB - Perforated Ceiling Diffuser. Halton THB. Perforated Ceiling Diffuser
Halton THB Perforated Ceiling Diffuser Horizontal air supply, suitable also for exhaust Installation either directly to ductwork or balancing plenum Detachable front panel enables the cleaning of the diffuser
CAV controllers. Type VFL. Volume flow limiter for insertion into ducting K
.1 X X testregistrierung CAV controllers Type Aerodynamic damper blade Sticker showing volume flow rates Set the volume flow rate Insert Volume flow limiter for insertion into ducting Circular, mechanical
VAV/CAV BOXES COMMERCIAL BUILDINGS INNOVATIVE VENTILATION & HEATING
VAV/CAV BOXES COMMERCIAL BUILDINGS A guide to VAV/CAV, including our unique product range, consultancy service and accessories. INNOVATIVE VENTILATION & HEATING www.pricetwa.co.uk At Price TWA we believe
Zest Iris Duct Dampers
lindab I the ventilation products specialist Zest Iris Duct Dampers Easily readable built in scale (100-315mm) Differential pressure measuring facility. Comprehensive size range. 100% open position allows
TBV - Terminal Unit. Halton TBV. Terminal Unit
Halton TBV Terminal Unit Horizontal air supply, suitable also for exhaust Integrated rectangular balancing plenum with measurement and adjustment functions Effective sound attenuation Circular duct connection
VAV terminal units. Type TVM. For dual duct systems PD TVM 1
X X testregistrierung VAV terminal units Type Variant -S Rectangular connection on the room end For dual duct systems VAV dual duct terminal units for dual duct systems with variable volume flows in buildings
Ceiling swirl diffusers with perforated face plate
X X testregistrierung Ceiling swirl diffusers with perforated face plate Type Horizontal swirling air discharge Diffuser face plate with perforated circular face style and exposed discharge nozzle Diffuser
ULA - Valve. Halton ULA. Valve
Halton ULA Valve Supply/exhaust valve for ceiling and wall installation with adjustable pressure loss Installation without an installation frame directly into ductwork or a hollow-core slab Flow pattern
Circular silencers. Type CA. For the reduction of noise in circular ducts, galvanised sheet steel construction. 02/2017 DE/en PD CA 1
X X testregistrierung Circular silencers Type For the reduction of noise in circular ducts, galvanised sheet steel construction Circular silencers Type for the reduction of noise in the circular ducts
PP CLEANING PIECES AND INSPECTION CHAMBERS FROM BTH
PP CLEANING PIECES AND INSPECTION CHAMBERS FROM Kunststoffartikel GmbH. H-3636 Vadna Kassai út 35-37. Hungary Tel: + 36 48 505 042 + 36 48 505 037 Fax: + 36 48 355 500 E-mail: fitting@bth.eu Internet:
Ventiduct nozzle ducts
Ventiduct nozzle ducts About Lindab Comfort and Design Product overview / symbols Theory Ceiling diffusers Ceiling diffusers - visible Plenum boxes Wall diffusers Nozzles Ventiduct Grilles Displacement
Accessories. Front vane panel Coupling sleeve with gasket Galvanised steel Gasket of rubber compound
Halton TSR/TSS Swirl Diffuser Radial horizontal air supply Air velocity is effectively reduced due to high mixing effect Circular duct connection with gasket All sizes available as an adapted version for
Type CS FOR THE REDUCTION OF NOISE IN CIRCULAR DUCTS, ALUMINIUM CONSTRUCTION
Homepage > Products > Sound attenuators > Circular silencers > Type CS Type CS FOR THE REDUCTION OF NOISE IN CIRCULAR DUCTS, ALUMINIUM CONSTRUCTION Circular silencers, in rigid aluminium construction,
DKS - Multi-nozzle Ceiling Diffuser. Halton DKS. Multi-nozzle Ceiling Diffuser
Halton DKS Multi-nozzle Ceiling Diffuser Horizontal air supply, vertical air patterns also possible Supply air pattern can freely be directed in up to four directions or alternatively radially as swirl
1/11 29/06/2016 CONTENTS 1. GENERAL DUCTS, AIR VENTS, VALVES MONOBLOCK UNITS FILTRATION CONTROL...
1/11 29/06/2016 VENTILATION AND Buildings & Technical Services Section AIR-CONDITIONING STANDARD CONTENTS 1. GENERAL... 2 2. DUCTS, AIR VENTS, VALVES... 2 3. MONOBLOCK UNITS... 3 4. FILTRATION... 5 5.
NR series. Circular CAV air volume control terminals with system powered mechanical regulator
series Circular CAV air volume control terminals Table of contents Description Page Type designation 1 Technical data - General 2 - Specification 3 - Installation instruction 3 overview / dimensions 4-5
CAV controllers. Type VFL. Volume flow limiter for insertion into ducting PD VFL 1
X X testregistrierung CAV controllers Type Aerodynamic damper blade Sticker showing volume flow rates Set the volume flow rate Insert Volume flow limiter for insertion into ducting Circular, mechanical
Incorporating V2.0. Product spec >>> > Series NV - Non vision grilles
Incorporating V2.0 Product spec >>> > Series NV - Non vision grilles Grilles Non-vision Recommended for: Wall & door Supply & extract Overview Block line of sight into private areas Giving adequate ventilation
Apartment ventilation
GB1250 04.18 AuraFlex LØV-R Apartment ventilation Diffusers in steel Customer adapted diffuser pattern Available in all colours Plenum box with damper and measuring outlet for commissioning Plenum box
Optima EXHAUST GRILL AND AIR LOUVER. Perforated Ceiling Diffusers. Features: Standard square sizes:
Perforated Ceiling Diffusers OPTIMA ceiling diffuser with perforated face, are recoended for heating, ventilating and cooling in centralized air conditioning systems. Perforated face diffusers, with 4-3-
Conveyor System ML2 ML2-1 MS2 MM3 ML2 MX2 DS2 DM3 DL2 DX2
Conveyor System Description 140mm width thermoplastic chain with aluminium frame conveyor system. Also available with stainless steel frame, please refer section. Examples of application industries Personal
THL - Conical Ceiling Diffuser. Halton THL. Conical Ceiling Diffuser
Halton THL Conical Ceiling Diffuser Horizontal or vertical air supply, suitable for both heating and cooling applications Adjustable throw pattern and pressure drop Installation flush to the ceiling, or
FDR - Fire Damper for Rectangular and Circular Ducts. Halton FDR. Fire Damper for Rectangular and Circular Ducts
Halton FDR Fire Damper for Rectangular and Circular Ducts Type-approved and compliant with the EN 1366-2 and EN 13501-3 standards. Design for installation in separating concrete and masonry walls and ceilings
Front panel Perforated galvanised steel Stainless steel AISI 316 as option Casing Galvanised steel Stainless steel AISI 316 as option
ZSC - Halton Zen Semi-Circle Displacement ventilation unit Capacity for wide supply airflow range. Uniform supply air distribution is achieved through small perforations, providing optimal conditions in
TRB - Conical Ceiling Diffuser. Halton TRB. Conical Ceiling Diffuser
Halton TRB Conical Ceiling Diffuser Horizontal or vertical air supply, suitable for both heating and cooling applications Supply air jet velocity is effectively reduced due to high mixing effect Installation
DCS - Ceiling Diffuser. Halton DCS. Ceiling Diffuser
Halton DCS Ceiling Diffuser DCS/C DCS/A DCS/N DCS/J DCS/P Horizontal air supply, suitable also for exhaust Modular construction with five different, interchangeable front panel options suited for modular
Duct System for Danfoss Air Units
MAKING MODERN LIVING POSSIBLE Installation Guide for Danfoss Air Units www.heating.danfoss.com Danfoss A/S is not liable or bound by warranty if these instructions are not adhered to during installation
Ventiduct nozzle ducts
Ventiduct nozzle ducts About Lindab Comfort and Design Product overview / symbols Theory Ceiling diffusers Ceiling diffusers - visible Plenum boxes Wall diffusers Nozzles Ventiduct Grilles Displacement
global leader in cables
Nexans, global leader in cables Total sales of 6 billion euros in 2010 The most complete range of cables and cabling systems Plants in 40 countries 23,700 employees worldwide Complete offers for every
TRH - Plenum for diffusers. Halton TRH. Plenum for diffusers
Plenum for diffusers Halton reserves the right to alter products without notice 07/15 Plenum ensuring proper function of supply air ceiling diffuser and connecting to ductwork Flexibility for levelling
Insulating Plastic Pipes with Armaflex. Insulating Plastic Pipes With...
Insulating Plastic Pipes With... WORKING WITH ARMAFLEX THE CORRECT USE OF ARMAFLEX ADHESIVE Use good quality tools, in particular a sharp knife, fresh Armaflex adhesive and a good brush. Oval tubes should
For installation into ductwork
X X testregistrierung Non-return dampers Type For installation into ductwork Non-return dampers prevent unwanted airflows against the intended airflow direction when the system is not in operation Maximum
Extraction arm FX100 Original
Bench top extraction systems for all environments. The Nederman bench top systems can be used in every type of environment, from assembly stations, where soldering fumes are extracted, to laboratories,
DKR - Multi-nozzle Ceiling Diffuser. Halton DKR. Multi-nozzle Ceiling Diffuser
Halton DKR Multi-nozzle Ceiling Diffuser Horizontal air supply, vertical air patterns are also possible Supply air pattern can freely be directed in up to four directions or alternatively radially as swirl
SYSTEMS FOR VEHICLE TESTING SYSTEMS REV M KIT AND REV A KIT
136 SYSTEMS FOR VEHICLE TESTING SYSTEMS REV M KIT AND REV A KIT Extraction kits for testing centres for cars, light commercial vehicles and heavy vehicles with manual or automatic return system Equipments
IN-LINE MIXED FLOW DUCT FANS TD-MIXVENT Series
Range of low profile in-line mixed flow duct fans manufactured in tough reinforced plastic (from 16 to 8 models) or with metal casing steel finished in a tough epoxy-polyester paint coating (from 1 to
Fans & extraction cooker hoods must have the correct size ducting. Please refer to the manufacturers recommended specification.
Ventilation Extraction of stale air & condensation from bathrooms & kitchens is a must to stop damp and mould. Good quality ventilation is essential for ensuring that you adhere to building regulations.
SAS International +44 (0) tubeline. tubular linear ceiling
metal ceilings SAS International +44 (0) 118 929 0900 www.sasint.co.uk tubeline tubular linear ceiling tubeline information System Description Tubeline is a visually striking linear ceiling system constructed
PSI Anti-Corrosion Tape
General information Technical specifications Requirement evaluation Application instructions Certificates PSI Anti-Corrosion Tape 8 Pipeline Accessories 85 The Systems PSI anti-corrosion tapes have been
Apartment ventilation
GB1250 06.18 AuraFlex LØV-R Apartment ventilation Diffusers in steel Customer adapted diffuser pattern Available in all colours Plenum box with damper and measuring outlet for commissioning Plenum box
series Silencers
series SK Silencers www.koolair.com Series SK 1 Silencers CONTENTS ASK-1 and ASK-2 Round Silencers Description 4 ASK-1 Overall Dimensions 5 ASK-2 Overall Dimensions 6 Selection Table and Weights 7 ASK-1
HR25 Solo. Installation and User Instructions. Through the Wall Heat Recovery Ventilators
abc GB HR25 Solo Installation and User Instructions Models:- HR25 Solo HR25 Solo L HR25 Solo H HR25 Solo LH Through the Wall Heat Recovery Ventilators PLEASE READ INSTRUCTIONS IN CONJUNCTION WITH ILLUSTRATIONS.
IN-LINE MIXED FLOW DUCT FANS TD-MIXVENT Series
Range of low profile in-line mixed flow duct fans manufactured in tough reinforced plastic (from to models) or with metal casing steel finished in a tough epoxy-polyester paint coating (from to models).
Ceiling swirl diffusers
X X testregistrierung Ceiling swirl diffusers Type RFD-Sirius, cross bar Horizontal swirling air discharge Circular diffuser face, integral measuring tubes is an air terminal device combined with a VAV
REK, LEK, ROK and LOK
REK, LEK, ROK and LOK Elegant and clear lined supply air diffusers for suspended ceilings. 06.6 REK, LEK, ROK and LOK Stylish supply air diffusers REK, LEK, ROK and LOK are designed for suspended ceilings
Shut-off dampers. Type AK-Ex. For low-leakage shut-off of volume flows in potentially. explosive atmospheres (ATEX) PD AK-Ex 1.
X X testregistrierung Shut-off dampers Type ATEX-compliant parts and units For low-leakage shut-off of volume flows in potentially explosive atmospheres (ATEX) Circular shut-off dampers for shutting off
IS94012-ENG - AFN February Revision 6 - Supersedes edition of 28 January and / or. 3 x Stress control mastic, type MFC (Hi-K)
IS94012-ENG - AFN 20-45 5 February 2013 - Revision 6 - Supersedes edition of 28 January 2013 Page 1 of 7 CAUTION: Read instructions thoroughly and completely prior to beginning installation. Installation
PRODUCT CATALOGUE EFFECTIVE FROM 1 ST JANUARY 2013 MULTI-LAYER PIPE & PRESS FITTING SYSTEM
PRODUCT CATALOGUE EFFECTIVE FROM 1 ST JANUARY 2013 MULTI-LAYER PIPE & PRESS FITTING SYSTEM PRESSTITE INTRODUCTION Introduction to Presstite Presstite Multilayer is a composite pipe system using the advantages
Flue installation instructions. Air flue duct for use with ecomax and ecotec boilers. For the installer
834449_05GB_022005.qd 02.02.2005 17:12 Uhr Seite 1 For the installer Flue installation instructions Air flue duct for use with ecomax and ecotec boilers ecomax 613/2 E ecomax 618/2 E ecomax 622/2 E ecomax
Type AK-Ex FOR LOW-LEAKAGE SHUT-OFF OF VOLUME FLOWS IN POTENTIALLY EXPLOSIVE ATMOSPHERES (ATEX)
Homepage > Products > Control units > Shut-off and restriction > Shut-Off Devices > Type AK-Ex Type AK-Ex FOR LOW-LEAKAGE SHUT-OFF OF VOLUME FLOWS IN POTENTIALLY EXPLOSIVE ATMOSPHERES (ATEX) Circular shut-off
Building Integrated Duct System
Mounting instruction Building Integrated Duct System Description We are facing one of the toughest challenges in decades. New buildings and existing homes must minimize their use of energy. In less than
Midea VRFs/ Midea V5X. Timothy Huang Senior Engineer
Midea VRFs/ Midea V5X Timothy Huang Senior Engineer VRF Product Overview General Features V5X Key Technologies V5X VRF product strategy VRF line-up Fresh air solutions Selection software Unique Innovations
F LEXIBLE DUCT VERSIONS
Ref. no.: 2-16 F LEXIBLE DUCT VERSIONS fo r a ll n e e d s o f t h e v en ti t la i n o y g lo o n h c te Aero - ALUFLEX duct Aero - ALUSTRETCH duct Aero - ALUFLEX isolated duct Aero - ALUFLEX attenuator
Square slots diffusers ALD610K and Combined ALD610K Series
Square slots diffusers ALD1K and Combined ALD1K Series Advantages Description ALD1K Selection tables Selection diagrams Description Combined ALD1K Selection tables Selection diagrams ALD 1 K Series aluminium
PURELINE18 PARTICULARLY SLIM DIFFUSER FACE, AVAILABLE IN NUMEROUS VARIANTS FOR MANY DIFFERENT INSTALLATION SITUATIONS
Homepage > Producten > Luchtroosters > Lijnroosters > Pureline18 PURELINE18 PARTICULARLY SLIM DIFFUSER FACE, AVAILABLE IN NUMEROUS VARIANTS FOR MANY DIFFERENT INSTALLATION SITUATIONS Slot diffusers with
Centrifugal performance characteristics with axial flow pattern: RADAX VAR
High pressure in-line mixed-flow fans RADAX VAR Centrifugal performance characteristics with axial flow pattern: RADAX VAR COMPACT PRESSURE-RESISTANT UNIVERSAL In their compact casing, the RADAX VAR impellers
PTS - Single-Blade Damper. Halton PTS. Single-Blade Damper
Halton PTS Single-Blade Damper Shut-off, adjustment, balancing or control damper Casing leakage classification: EN 1751, Class C Casing and damper blade made of galvanised steel Tightness classification
COLIBRI Ceiling QUICK FACTS. Square ceiling diffuser with discs for supply air
Square ceiling diffuser with discs for supply air QUICK FACTS Adjustable discs flexible spread pattern Can be used for vertical air diffusion Swirl function Also available in the Extract air version Designed
Type VSD35. Nominal length up to 1500 mm: one spigot
Type VSD35 Nominal length up to 1500 mm: one spigot NUMEROUS VARIANTS FOR MANY DIFFERENT INSTALLATION SITUATIONS Slot diffusers with 35 mm diffuser face (nominal width) and adjustable air control elements
CADENZA. Sound attenuator with tapered acoustic baffles for rectangular ducts QUICK FACTS
Sound attenuator with tapered acoustic baffles for rectangular ducts QUICK FACTS Rectangular sound attenuator with connection to the outer casing, which also enables flange connection Excellent aerodynamic
Max. particle size 5 µm. Pressure for determining piston forces Repetitive precision. Polyurethane
Piston rod cylinders Guide cylinders 1 Ambient temperature min./max. +0 C / +60 C edium Compressed air ax. particle size 5 µm Oil content of compressed air 0 mg/m³ - 1 mg/m³ Pressure for determining piston
m e c h a t r o n i c c o m p a n y p r o t e c t i o n air & fluid s y s t e m s GB We protect technology.
c o m p a n y p r o t e c t i o n c o n n e c t i o n a i r & f l u i d m e c h a t r o n i c air & fluid s y s t e m s GB company protection connection air & fluid mechatronic Our Competences protection
nxds DRY SCROLL PUMP THE ULTIMATE DRY CHOICE
nxds DRY SCROLL PUMP THE ULTIMATE DRY CHOICE With exceptional pumping capability, ultimate vacuum performance and state-of-the-art design features, the nxds dry scroll pump is the best performing pump
VT-SENSOR AIR VELOCITY AND TEMP
home VTSENSOR AIR VELOCITY AND TEMP Ultra low velocity pressure measurement Traceable Calibration Certificate Excellent repeatability Self compensating zero Climate chamber compensated Long term span stability
series 90-GV Variable geometry units
series 90-GV Variable geometry units www.koolair.com 1 S-90-GV Variable geometry unit CONTENTS Description and coding 2 Operation 3 Dimensions 4 Technical data 4 2 S-90-GV Variable geometry unit Description
HIGH INDUCTION DIFFUSERS WITH VARIABLE GEOMETRY
VARIABLE GEOMETRY OVERVIEW CHARACTERISTICS APPLICATIONS KQ OVERVIEW : KQ high induction diffusers with variable geometry are a new type of air diffusion equipment. Their unique deflector adjustment system
Floor Swirls Models BZD and SZD
July 09 Floor Swirls Floor Swirls Models BZD and SZD Features Model BZD Circular Floor Swirl Model SZD Circular Step Diffuser Grilles Diffusers Louvres Chilled Beams Ruskin Air Management Limited www.ruskinuk.co.uk
Engineering Data Manual. New : available with EC motor. High Static Pressure Ductable Fan Coil Unit. Models 07 to to 4650 m 3 /h
Engineering Data Manual New : available with EC motor VH High Static Pressure Ductable Fan Coil Unit Models 07 to 27 800 to 4650 m 3 /h General Characteristics Presentation On model VH 07, coils have 4
INDEX. Chapter1 0. air master. Round Ceiling Diffusers
air master Chapter1 0 INDEX A. Round ceiling diffusers 1. Fixed round ceiling diffuser...: ARDF...10.1 2. Round ceiling diffuser with adjustable pattern...: ARD...10.2 Standard sizes...10.3 Air pattern...10.3
SMOKE CONTROL DAMPERS
SMOKE CONTROL DAMPERS 96 - CPD - 0058 Round DKIR and Rectangular DKIS ORIGINAL INSTALLATION, OPERATION AND MAINTENANCE MANUAL EVERY SMOKE DAMPER NEEDS TO BE INSTALLED IN ACCORDANCE WITH THIS MANUAL! /
LE MODELS: SHIPPING, RIGGING, LIFTING, ASSEMBLY MANUAL
4510 Helgesen Drive, Madison, WI 53718 (608) 221-4499, (800) 627-4499, Fax: (608) 221-2824 LE MODELS: SHIPPING, RIGGING, LIFTING, ASSEMBLY MANUAL This manual provides an overview of shipping, rigging,
Slot diffusers, Round duct diffusers. IMP Klima
, Round duct diffusers 04 Round duct diffusers 176 , Round duct diffusers SLOT DIFFUSERS, ROUND DUCT DIFFUSERS SWIRL DIFFUSERS, VARIABLE SWIRL DIFFUSERS CIRCULAR DIFFUSERS, SQUARE DIFFUSERS VENTILATING
RPD ROUND PLAQUE DIFFUSER
ROUND PLAQUE DIFFUSER s (RPD) provide a balance between engineering and architectural needs, with a flush appearance and superior VAV performance in both ceiling and exposed duct mounting applications.
ACTIVENT System. Specifications. Product code example ACTA
Activent is a ventilation system for supplying and distributing air. The system has been proven to function effectively in both small and large areas and is used in all types of premises ranging from offices
Catalogue of Accessories
Catalogue of Accessories Room Controller with CO 2 Sensor 3 CO 2 Sensor 4 F7 Filter 400 x 220 x 48 mm 5 Carbon Filter 6 Design valve circle 7 (for pipes Ø 100, 125 and 160) Design valve square 8 (for pipes
DVAX-ARS. Roof-mounted unit for mechanical smoke extract
Fans Air Handling Units Air Distribution Products Fire Safety Air Curtains and Heating Products Tunnel Fans DVAX- Roof-mounted unit for mechanical smoke extract 2 DVAX DVAX- Roof-mounted axial fan unit
MITSUBISHI TRITON MQ (2015 +) AEROSTYLE 4X4 2 POST 3 POST 4 POST 5 POST
INSTALLATION GUIDE BULLBAR MITSUBISHI TRITON MQ (2015 +) AEROSTYLE 4X4 2 POST 3 POST 4 POST 5 POST Version 171010_1 PLEASE READ THE INSTALLATION GUIDE CAREFULLY BEFORE FITTING PRODUCT TO VEHICLE WHEN INSTALLED
HIGH INDUCTION DIFFUSERS WITH VARIABLE GEOMETRY
HIGH INDUCTION DIFFUSERS WITH VARIABLE GEOMETRY OVERVIEW CHARACTERISTICS APPLICATIONS KQ OVERVIEW : KQ high induction diffusers with variable geometry are a new type of air diffusion equipment. Their unique
XXII Jornadas del Arroz Zaragoza (Spain) 9 th March 2016 EU RICE MARKET. Damien PLAN European Commission DG AGRI
XXII Jornadas del Arroz Zaragoza (Spain) 9 th March 2016 EU RICE MARKET Damien PLAN European Commission DG AGRI Contents 1. EU Rice - Overview 2. EU Rice Trade Imports/Exports 3. EU Rice Market 2015/16
TD-MIXVENT Series IN-LINE MIXED FLOW DUCT FANS TD-MIXVENT. In-Line duct fans
IN-LINE MIXED FLOW DUCT FANS Series Range of low profile in-line mixed flow duct fans manufactured in tough reinforced plastic (from 160 to 800 models) or with metal casing steel finished in a tough epoxy-polyester
(L=500) L=300 (L=500) PL /E... electric actuator version. Table standard dimensions, L = 300 mm.
Fire damper pl-30 General characteristics Application Fire dampers prevent fire and smoke from spreading through ventilation ducts in buildings. The dampers are intended for use inside buildings and are
Incorporating V2.1. Product spec >>> > Series ECG - Egg crate grilles
Incorporating V2.1 Product spec >>> > Series ECG - Egg crate grilles Grilles Egg crate Recommended for: Wall, ceiling & duct Extract Overview Industry standard extract grille Plastic egg crate core optional
(click on page links below) General & Performance Data 1. Suggested Spec 3. Accessories 4
HAR Variable Air Volume Diffusers Contents: (click on page links below) General & Performance Data 1 Suggested Spec 3 Accessories 4 AUCKLAND ph 09 279 5250 fax 09 275 5637 sales@temperzone.co.nz WELLINGTON
J L I e x h a u s t h o o d
JLI exhaust hood PAGE Table of Contents Product description & Product code Functioning principle, Parts Dimensions Positioning, Design Service Exhaust air 7 Pressure loss & Sound data, Lights 8 We want