PURELINE18 PARTICULARLY SLIM DIFFUSER FACE, AVAILABLE IN NUMEROUS VARIANTS FOR MANY DIFFERENT INSTALLATION SITUATIONS

Transcription

1 Homepage > Producten > Luchtroosters > Lijnroosters > Pureline18 PURELINE18 PARTICULARLY SLIM DIFFUSER FACE, AVAILABLE IN NUMEROUS VARIANTS FOR MANY DIFFERENT INSTALLATION SITUATIONS Slot diffusers with 18 mm diffuser face (nominal width) and adjustable air control elements Nominal length mm (length of air control element 100 mm), 1 or 2 slots Volume flow rate range 5 84 l/s or m³/h Individually adjustable air control elements for horizontal, angled or vertical air discharge One-way or alternating air discharge meets individual local requirements Uniform air pattern reduces contamination of the ceiling due to the induction of room air Air control elements have grooves that allow for precise positioning Optional equipment and accessories Attractive appearance due to extruded aluminium sections with anodised finish or powder coating Symmetric or asymmetric position of plenum box Plenum box with lining End plates, end angles, corner sections Different looks due to choice of black, grey or white air control elements

2 APPLICATION Application Type PureLine18 slot diffusers are used as supply air or extract air devices in comfort zones Particularly unobtrusive diffuser due to its sleek design Installation into suspended ceilings For room heights up to 4 m (lower edge of suspended ceiling) For suspended ceilings; suitable for restricted ceiling voids due to the low overall height of the plenum box Suitable for continuous linear arrangement Adjustable air control elements allow for horizontal, angled or vertical air discharge Mixed flow system with one-way or alternating air discharge, can be adapted to the building structure High induction results in a rapid reduction of the temperature difference and airflow velocity (supply air variant) For variable and constant volume flows For supply air to room air temperature differences from 10 to +10 K Special characteristics Uniform air pattern reduces contamination of the ceiling due to the induction of room air Horizontal, angled or vertical air discharge by means of manually adjustable air control elements Comfortable indoor air climate due to high induction and rapid reduction of temperature differences and airflow velocities High-quality look thanks to anodised extruded aluminium sections (E6-C-0, natural colour) or powder coating (RAL CLASSIC colour) Diffuser face has been optimised for maximum volume flow rate at low sound power levels Suitable for continuous linear arrangement Nominal sizes L : 600, 700, 800, 900, 1000, 1100, 1200, 1300, 1400, 1500, 1600, 1700, 1800, N

3 1900, 2000 mm Diffuser face also available in intermediate sizes DESCRIPTION Variants PL18-*: 1 or 2 slots PL18-*-DF: Diffuser face with spring clip PL18-*-DS: Diffuser face with extended border (B00) and screw fixing PL18-*-PB: Plenum box for screw fixing PL18-*-PF: Diffuser face and plenum box, non-detachable fixing PL18-*-SF: Diffuser face and plenum box, detachable fixing PL18-*-CS: Corner section Position of plenum box on the front diffuser Central position On the left (LE) On the right (RI) Plenum box variant Symmetric position of plenum box, side entry spigot (HS) Symmetric position of plenum box, top entry spigot (VS) Asymmetric position of plenum box, side entry spigot (HA) Construction Diffuser face finish Anodised, E6-C-0, natural colour P1: Powder-coated RAL 9010, pure white, gloss level 50% P1: Powder-coated RAL 9006, white aluminium, gloss level 30% P1: Powder-coated in any other RAL CLASSIC colour, gloss level 70% Attachments

4 D: Damper blade for volume flow rate balancing LS: Lip seal L: Internal insulation EP: Two end plates EA: Two end angles Single diffusers are factory fitted with end plates or end angles. Accessories EP: Two end plates EA: Two end angles For a continuous linear arrangement the end plates or end angles have to be ordered separately and fitted by others. Construction features Spigot suitable for circular ducts to EN 1506 or EN suspension points for on-site installation (by others) The manually adjustable air control elements have grooves that make it easier to adjust the elements and lock them in the required position Spigot with groove for lip seal (if accessory with lip seal has been ordered) Diffuser face sizes from 600 to 2000 mm, in increments of 1 mm Plenum boxes are only available in nominal lengths Materials and surfaces Diffuser face made from extruded aluminium sections Air control elements made of ABS plastic, UL 94, V-0, flame retardant Plenum box made of galvanised sheet steel End plates and end angles made of aluminium Lip seal made of rubber Lining is mineral wool with vinyl closed cell foam Diffuser face with anodised finish, E6-C-0, natural colour P1: Powder-coated, RAL CLASSIC colour Air control elements similar to RAL 9005, black G: Air control elements similar to RAL 9006, grey W: Air control elements similar to RAL 9010, white

5 Mineral wool Where the mineral wool comes into contact with air, it is faced with glass fibre fabric as a protection against abrasion due to airflow velocities up to 20 m/s To EN 13501, fire rating class A1, non-combustible RAL quality mark RAL-GZ 388 Biosoluble and hence hygienically safe according to the German TRGS 905 (Technical Rules for Hazardous Substances) and EU directive 97/69/EC Inert to fungal and bacterial growth Standards and guidelines Sound power level of the air-regenerated noise measured according to EN ISO 5135 Maintenance Maintenance-free as construction and materials are not subject to wear Inspection and cleaning to VDI 6022 TECHNISCHE INFORMATIE Function, Technical data, Quick sizing, Specification text, Order code FUNCTION Functional description Slot diffusers direct the air from air conditioning systems into the room, either horizontally, at an angle or vertically. The resulting airflow induces high levels of room air, thereby rapidly reducing the airflow velocity and the temperature difference between supply air and room air. The result is a mixed flow ventilation in comfort zones, with good overall room ventilation, creating only very little turbulence in the occupied zone.

6 Type PureLine18 slot diffusers are factory fitted with manually adjustable air control elements. The air pattern can be adjusted to meet different local requirements. Air discharge is one-way or alternating horizontal. Other patterns: heating mode with vertical air discharge; angled air discharge. The supply air to room air temperature difference may range from 10 to +10 K. A damper blade (optional) simplifies volume flow rate balancing for commissioning. To give rooms an aesthetic, uniform look, PureLine18 diffusers may also be used for extract air. Schematic illustration of PL18-*-SF

7 1 Diffuser face, 1 slot or 2 slots 2 Adjustable air control element 3 Screw fixing 6 Neck 7 Plenum box 8 Suspension lug 9 Spigot Optional

8 4 End plate 5 End angle 10 Lip seal Damper blade for volume flow rate balancing Alternating horizontal air discharge

9 Alternating angled air discharge (AS) Setting of the air control elements

10

11 Air discharge: horizontal left Setting of the air control elements

12

13 Air discharge: horizontal right Alternating angled air discharge Alternating angled air discharge (AS)

14 Setting of the air control elements

15

16 Air discharge: angled right Setting of the air control elements

17

18 Air discharge: angled left Vertical air discharge Vertical air discharge (V)

19

20 Setting of the air control elements

21

22 Air discharge: vertical One-way horizontal air discharge to the left One-way horizontal left (HL)

23 Setting of the air control elements

24

25 Air discharge: horizontal left One-way horizontal air discharge to the right One-way horizontal right (HR)

26 Setting of the air control elements

27

28 Air discharge: horizontal right TECHNICAL DATA Nominal length mm, in increments of 100 mm Number of slots 1 or 2 Minimum volume flow rate, with Δt = 10 K z 5 l/s or 17 m³/h Maximum volume flow rate, with L 50 db(a) 84 l/s or 302 m³/h WA Supply air to room air temperature difference 10 to +10 K QUICK SIZING Quick sizing tables provide a good overview of the volume flow rates and corresponding sound power levels and differential pressures. Exact values for all parameters can be determined with our Easy Product Finder design programme. Up to nominal length 1500 mm, sizing includes one spigot; from length 1600 mm, two spigots are required. PL18-1, supply air, alternating horizontal air discharge, sound power level and total differential pressure Nominal length Nominal length V V Damper blade position D = 78 D = 98 D = 78 D = 98 D = 78 D = 98 Δpt LWA Δpt LWA Δpt LWA Δpt LWA Δpt LWA Δpt LWA Nominal length l/s m³/h Pa db(a) Pa db(a) Pa db(a) Pa db(a) Pa db(a) Pa db(a) <15 3 <15 5 <15 4 <15 8 <15 5 < <15 3 <15 6 <15 4 <15 10 <15 6 <15

29 <15 3 <15 6 <15 4 <15 12 <15 7 < <15 4 <15 7 <15 5 <15 14 <15 7 < <15 4 <15 8 <15 5 <15 16 <15 8 < <15 4 <15 9 <15 6 <15 19 <15 10 < <15 4 < < <

30 < < < < < < < < <15 3 <15 6 <15 4 <15 12 <15 7 < <15 3 <15 7 <15 5 <15 13 <15 7 <

31 <15 4 < < < < < < < < < PL18-2, supply air, alternating horizontal air discharge, sound power level and total differential pressure Nominal length Nominal length V V Damper blade position D = 98 D = 123 D = 98 D = 123 D = 98 D = 123 Δpt LWA Δpt LWA Δpt LWA Δpt LWA Δpt LWA Δpt LWA Nominal length l/s m³/h Pa db(a) Pa db(a) Pa db(a) Pa db(a) Pa db(a) Pa db(a) <15 4 <15 6 <15 4 <15 11 <15 6 <

32 <15 4 <15 7 <15 5 <15 13 <15 7 < <15 4 <15 9 <15 5 < < < < < < < <

33 < < <

34 SPECIFICATION TEXT Slot diffusers of Type PL18, with individually manually adjustable air control elements and 1 or 2 slots. Air discharge can be alternating horizontal, alternating angled, vertical, one-way horizontal to the left or one-way horizontal to the right. The slot diffusers are intended to be installed in suspended ceilings and are suitable for supply air and extract air. Ready-toinstall component which consists of a diffuser face with a choice of black, grey or white air control elements. Variants with plenum box have 1 or 2 spigots; symmetrically positioned plenum boxes may have side entry or top entry spigots, while asymmetrically positioned plenum boxes have only side entry spigots. The plenum boxes are fitted with 4 suspension lugs.

35 The diffuser face fixing can be detachable or non-detachable. Spigots are suitable for circular ducts according to EN 1506 or EN The sound power level of air-regenerated noise is measured according to EN ISO Special characteristics Uniform air pattern reduces contamination of the ceiling due to the induction of room air Horizontal, angled or vertical air discharge by means of manually adjustable air control elements Comfortable indoor air climate due to high induction and rapid reduction of temperature differences and airflow velocities High-quality look thanks to anodised extruded aluminium sections (E6-C-0, natural colour) or powder coating (RAL CLASSIC colour) Diffuser face has been optimised for maximum volume flow rate at low sound power levels Suitable for continuous linear arrangement Materials and surfaces Diffuser face made from extruded aluminium sections Air control elements made of ABS plastic, UL 94, V-0, flame retardant Plenum box made of galvanised sheet steel End plates and end angles made of aluminium Lip seal made of rubber Lining is mineral wool with vinyl closed cell foam Diffuser face with anodised finish, E6-C-0, natural colour P1: Powder-coated, RAL CLASSIC colour Air control elements similar to RAL 9005, black G: Air control elements similar to RAL 9006, grey W: Air control elements similar to RAL 9010, white Mineral wool Where the mineral wool comes into contact with air, it is faced with glass fibre fabric as a protection against abrasion due to airflow velocities up to 20 m/s To EN 13501, fire rating class A1, non-combustible RAL quality mark RAL-GZ 388 Biosoluble and hence hygienically safe according to the German TRGS 905 (Technical Rules for Hazardous Substances) and EU directive 97/69/EC Inert to fungal and bacterial growth

36 Construction Diffuser face finish Anodised, E6-C-0, natural colour P1: Powder-coated RAL 9010, pure white, gloss level 50% P1: Powder-coated RAL 9006, white aluminium, gloss level 30% P1: Powder-coated in any other RAL CLASSIC colour, gloss level 70% Technical data Nominal length: mm, in increments of 100 mm Number of slots: 1 or 2 Minimum volume flow rate, with Δt = 10 K: 5 l/s or 17 m³/h Maximum volume flow rate, with L 50 db(a): 84 l/s or 302 m³/h Supply air to room air temperature difference: 10 to +10 K z WA Sizing data V [m³/h] Δp [Pa] t Air-regenerated noise L [db(a)] WA This specification text describes the general properties of the product. Texts for variants can be generated with our Easy Product Finder design programme. ORDER CODE Order example: PL18-1-S-PF-HS/1200x1200x98/1

37 Number of slots 1 System Supply air Variant Diffuser face fixed to the plenum box, non-detachable Plenum box variant Symmetric position of plenum box, side entry spigot Nominal size Diffuser face 1200 mm, plenum box 1200 mm, spigot diameter 98 mm No. of spigots 1 Damper blade for volume flow rate balancing Without Lip seal Without Lining Without Position of plenum box Central position Air pattern Alternating horizontal Extended border Without End pieces Without Surface Anodised, E6-C-0, natural colour Colour of air control elements Black Order example: PL18-2-S-SF-HS/1200x1000x123/2-D-LS-L-LE/AS/B00/EA/P1-RAL 9010/W

38 Number of slots 2 System Supply air Variant Diffuser face fixed to the plenum box, detachable Plenum box variant Symmetric position of plenum box, side entry spigot Nominal size Diffuser face 1200 mm, plenum box 1000 mm, spigot diameter 123 mm No. of spigots 2 Damper blade for volume flow rate balancing With Lip seal With Lining With Position of plenum box Left side Air pattern Alternating angled Extended border With End pieces With end angle Surface Powder-coated RAL 9010, pure white, gloss level approx. 50% Colour of air control elements White Order example: PL18-2-S-DF/1200/V/B00/EP/P1-RAL 9006/G

39 Number of slots 2 System Supply air Variant Diffuser face with extended border and spring clip Plenum box variant No plenum box Nominal size Diffuser face 1200 mm No. of spigots Without Damper blade for volume flow rate balancing Without Lip seal Without Lining Without Position of plenum box No plenum box Air pattern Vertical Extended border With extended border End pieces With end plate Surface Powder-coated RAL 9006, white aluminium, gloss level approx. 30% Colour of air control elements Grey Order example: PL CS/150x300x90/B00/RAL 9016

40 Number of slots 2 Variant Corner section Dimensions Leg length E: 150 mm; leg length F: 300 mm; 90 angle Extended border With extended border (B00) Surface P1: Powder-coated RAL 9016, traffic white, gloss level approx. 70% Type PureLine18 Slot diffuser Damper blade for volume flow rate balancing No entry: none Number of slots 1 1 slot 2 2 slots System D LS With damper blade Lip seal No entry: none With lip seal S E Supply air Extract air Plenum box lining No entry: none Variant L With DF DS Diffuser face with extended border (B00) and spring clip Diffuser face with extended border (B00) and fixing screws Position of plenum box No entry: centre Plenum box LE RI Left side Right side PB PF Plenum box only Diffuser face fixed to the plenum box, non-detachable Air pattern (100 mm air control element) SF Diffuser face fixed to the plenum box, detachable (only with B00) Plenum box variant AS HL No entry: alternating horizontal Alternating angled Horizontal left

41 HS Symmetric position of plenum box, side entry spigot HR Horizontal right VS Symmetric position of plenum box, top entry spigot V Vertical HA Asymmetric position of plenum box, side entry spigot Extended border Nominal size [mm] No entry: none Diffuser face x Plenum box x Spigot diameter B00 With (B00) Nominal size LN EP EA End pieces No entry: none End plate End angle Surface No entry: anodised, E6-C-0, natural colour P1 Powder-coated, specify RAL CLASSIC colour W G Colour of air control elements No entry: similar to RAL 9005, black Similar to RAL 9010, white Similar to RAL 9006, grey Plenum box LN

42 Spigot diameter ØD 78 With 1 slot 98 With 1 or 2 slots 123 With 2 slots No. of spigots 1 1 spigot 2 2 spigot Type Dimensions [mm] PureLine18 Slot diffuser E 100 to 300 mm (in increments of 1 mm) Number of slots 1 1 slot 2 2 slots System Note: no entry required Variant F 100 to 300 mm (in increments of 1 mm) W 45 to 175 (in increments of 1 ) Extended border No entry: none B00 With (B00) Surface No entry: anodised, E6-C-0, natural colour CS Corner section P1 Powder-coated, specify RAL CLASSIC colour Colour of air control elements No entry: similar to RAL 9005, black W Similar to RAL 9010, white G Similar to RAL 9006, grey Variants, Dimensions and weight

43 VARIANTS Asymmetrically positioned plenum box DIMENSIONS AND WEIGHT Nominal length

44 Nominal length L₁ mm Variant

45 With extended border Variant P Variant mm PL PL Dimensions [mm] Nominal length L₁ L₃

46 Variant Variant B3 H4 R M A O PL18-1-HS / HA PL18-2-HS / HA PL18-1-VS PL18-2-VS PL18-1-PF-HA 54 PL18-2-PF-HA 67 PL18-1-SF-HA 50 PL18-2-SF-HA 63 Variant Variant D C PL PL Weights

47 Plenum box variant Diffuser face Variant kg/m PL PL Plenum box HS/HA PL PL Plenum box VS PL PL Total weight = weight of diffuser face + weight of plenum box Variant Variant Variant Without extended border With extended border P mm PL PL E F W Min. entry value Max. entry value Variant

48 Without extended border With extended border Variant P Variant mm PL PL End angles on both ends Without end piece

49 PL18-1 profile PL18-2 profile

50 PL18-1/B00 profile

51 PL18-2/B00 profile

52 PL18-1-*-DF (diffuser face with spring clip)

53 PL18-2-*-DF (diffuser face with spring clip)

54 Plenum box with side entry spigot (HS / HA)

55 Plenum box with top entry spigot (VS)

56 Plenum box fixing points

57 Spigot arrangement

58 * only with construction VS Note: Plenum box with choice of 1 spigot or 2 spigots. PL18-*-HS (symmetric position of plenum box, side entry spigot)

59 Illustration shows PL18-1-HS PL18-*-HA (asymmetric position of plenum box, side entry spigot)

60 Illustration shows PL18-1-HA PL18-*-VS (symmetric position of plenum box, top entry spigot)

61 Illustration shows PL18-1-VS PL18-*-CS

62 End plate EP

63 Profile without extended border End plate EP

64 Profile with extended border End angle EA Profile without extended border End angle EA

65 Profile with extended border Installation examples, Installation details, Commissioning, Basic information and nomenclature

66 INSTALLATION EXAMPLES PL18-1/.../B00, installation in continuous ceilings Anodised, E6-C-0, natural colour INSTALLATION DETAILS Installation and commissioning For room heights up to 4 m (lower edge of suspended ceiling) Flush ceiling installation Horizontal or vertical duct connection If (L₃+ 5) < L, the plenum box can be positioned to the left, to the right or in the centre. 1 For a continuous linear arrangement connect the diffusers with alignment plates If necessary, carry out volume flow rate balancing with the damper blade Fixing material for fixing the slot diffusers is to be provided by others

67 These are only schematic diagrams to illustrate installation details. PL plenum box, positioned on the left, in the centre, on the right Suspension

68 PL18-DF spring clip fixing If ceiling thickness is > 9 mm PL18-DF spring clip fixing If ceiling thickness is 9 mm Continuous ceiling

69 Rectangular panels

70 PL18 with detachable diffuser face fixing

71 Continuous linear arrangement

72 Each slot diffuser (without end pieces) is supplied with two alignment plates Fitting corner sections

73 COMMISSIONING Volume flow rate balancing When several diffusers are connected to just one volume flow controller, it may be necessary to balance the volume flow rates. Slot diffusers with plenum box and damper blade (variant -D): The damper blade can be adjusted even after the diffuser face has been installed. Volume flow rate balancing

74 Home Contacten Imprint Leverings- en betalingsvoorwaarden Privacy Disclaimer TROX Nederland B.V.

75 Homepage > Producten > Luchtroosters > Lijnroosters > Pureline18 Move the air control element near the spigots in such a way that it is possible to insert a screw driver BASIC INFORMATION AND NOMENCLATURE Principal dimensions ØD [mm] Outer diameter of the spigot L₁ [mm] Length of diffuser without end pieces L₃ [mm] Length of plenum box P [mm] Width of diffuser face with extended border, if any B₃ [mm] Width of plenum box H₃ [mm] Height of slot diffuser with plenum box, from the lower edge of the suspended ceiling to the upper edge of the plenum box Y [mm] Neck extension The neck length results from a fixed length plus the neck extension A [mm] Position of the spigot, defined by the distance of the spigot centre line to the lower edge of the suspended ceiling C [mm] Length of the spigot m [kg] Home Contacten Imprint Leverings- en betalingsvoorwaarden Privacy Disclaimer TROX Nederland B.V.

76 Homepage > Producten > Luchtroosters > Lijnroosters > Pureline18 Weight Nomenclature L [db(a)] WA A-weighted sound power level of air-regenerated noise V [m³/h] and [l/s] Volume flow rate Δt [K] z Supply air to room air temperature difference, i.e. supply air temperature minus room temperature Δp [Pa] t Total differential pressure A [m²] eff Effective air discharge area All sound power levels are based on 1 pw. Home Contacten Imprint Leverings- en betalingsvoorwaarden Privacy Disclaimer TROX Nederland B.V.

77 Homepage > Producten > Luchtroosters > Lijnroosters > Pureline18 TROX Nederland B.V. Online-Services Service-Hotlines Orderstatus (My TROX-NET) Uw contactpersoon Online service contact formulier Aanvraag prijslijst TROX klimaat TROX Nederland B.V. Tel.: +31 (0) Fax : +31 (0) Contact Veersteeg 11, 4212 LR Spijk Postbus 225, 4200 AE Gorinchem Tel.: +31 (0) Fax.: +31 (0) trox@trox.nl Levertijden: productietijd+2 werkdagen Home Contacten Imprint Leverings- en betalingsvoorwaarden Privacy Disclaimer TROX Nederland B.V.