Test Report No.: SDHL FT Date: Jun.15, 2017 Page 1 of 5

Transcription

1 Test Report No.: SDHL FT Date: Jun.15, 2017 Page 1 of 5 SHENGZHAO FURNITURE FACTORY LIANGYONG INDUSTRIAL ZONE, ZHENNAN JIUJIANG TOWN, FOSHAN CITY, GUANGDONG PROVINCE, CHINA The following sample(s) was / were submitted and identified on behalf of the client as: Sample Description Manufacturer Country of Origin : SZ-B819 OFFICE CHAIR : SHENGZHAO FURNITURE FACTORY : CHINA Sample Receiving Date : May 26, 2017 Test Performing Date : May 26, 2017 to Jun.15, 2017 Test(s) Requested Test Result Summary Backrest Strength Test - Static - Type l and II, Backrest Strength Test - Static - Type lll and Backrest Durability Test - Cyclic - Type l of ANSI/BIFMA X (Type I, III) Summary: 1. For further details, please refer to the following page(s). Result(s) Signed for and on behalf of Shunde Branch SGS-CSTC Co., Ltd. Caming Fan Approved signatory

2 Test Report No.: SDHL FT Date: Jun.15, 2017 Page 2 of 5 TESTS AND RESULTS Test Conducted: Backrest Strength Test - Static - Type l and II, Backrest Strength Test - Static - Type lll and Backrest Durability Test - Cyclic - Type l of ANSI/BIFMA X General-Purpose Office Chairs Tests. No. of Sample: 2 piece(s) (Sample 1, 2). For more sample information and pictures, please refer to the following page. Chair Type: Type I, III. Test and Requirements 5 Backrest Strength Test - Static - Type l and II Functional Load There shall be no loss of serviceability to the chair when 667 N (150 lbf.) is applied to the backrest at the specified position for one (1) minute. With the backrest at its back stop position, apply a force that is initially 70 degrees ± 10 degrees to the plane of the backrest. The force is not intended to be maintained at 70 degrees ± 10 degrees throughout the loading of the backrest Proof Load There shall be no sudden and major change in the structural integrity of the chair, loss of serviceability is acceptable, when 1001 N (225 lbf.) is applied to the backrest at the specified position for one (1) minute. With the backrest at its back stop position, apply a force that is initially 70 degrees ± 10 degrees to the plane of the backrest. The force is not intended to be maintained at 70 degrees ± 10 degrees throughout the loading of the backrest. 6 Backrest Strength Test - Static - Type lll Functional Load There shall be no loss of serviceability to the chair when 667 N (150 lbf.) is applied to the backrest at the specified position for one (1) minute. With the backrest at its back stop position, apply a force that is initially 90 degrees ± 10 degrees to the plane of the backrest. The force is not intended to be maintained at 90 degrees ± 10 degrees throughout the loading of the backrest Proof Load There shall be no sudden and major change in the structural integrity of the chair, loss of serviceability is acceptable, when 1001 N (225 lbf.) is applied to the backrest at the specified position for one (1) minute. With the backrest at its back stop position, apply a force that is initially 90 degrees ± 10 degrees to the plane of the backrest. The force is not intended to be maintained at 90 degrees ± 10 degrees throughout the loading of the backrest. Test Results

3 Test Report No.: SDHL FT Date: Jun.15, 2017 Page 3 of 5 Test and Requirements 14 Backrest Durability Test - Cyclic - Type l A weight of 109 kg (240 lb.) shall be secured in the center of the seat. Apply a 445 N (100 lbf.) total force to the backrest at the specified position at a rate between 10 and 30 cycles per minute. For chairs with backrest widths less than or equal to 406 mm (16 in.) at the height of the loading point, apply the load to the backrest for 120,000 cycles. For chairs with backrest widths greater than 406 mm (16 in.) at the height of the loading point, apply the load to the backrest for 80,000 cycles + 20,000 cycles at the position 102 mm (4 in.) to the right of the vertical centerline + 20,000 cycles at the position 102 mm (4 in.) to the left of the vertical centerline.. There shall be no loss of serviceability. Note: With the backrest at its back stop position, apply a force that is initially 90 degrees ± 10 degrees to the plane of the backrest. The force is not intended to be maintained at 90 degrees ± 10 degrees throughout the loading of the backrest. Test Results Remark: 1. For the sample information and pictures, please refer to the following page.

4 Test Report No.: SDHL FT Date: Jun.15, 2017 Page 4 of 5 Weight: Sample #1: kg Sample #2: kg SAMPLE INFORMATION AND PICTURES Overall Dimensions: Sample #1: 760 mm L x 725 mm W x 1180~1250 mm H Sample #2: 750 mm L x 713 mm W x 960~1028 mm H Other Dimensions: Base radius, 358 mm; base weight, 2.0 kg. Sample as Received Sample #1 - View 1 Sample #1 - View 2 Sample #1 - View 3 Sample #1 - View 4

5 Test Report No.: SDHL FT Date: Jun.15, 2017 Page 5 of 5 Sample #2 - View 5 Sample #2 - View 6 Sample #2 - View 7 Sample #2 - View 8 Sample #1&2 - View 9 ***End of Report***