STRAIN LINK STICK ROLLER LINK STICK ADJUSTABLE STRAIN POLES SPIRAL LINK STICK TRANSMISSION TOOLS

Size: px

Start display at page:

Download "STRAIN LINK STICK ROLLER LINK STICK ADJUSTABLE STRAIN POLES SPIRAL LINK STICK TRANSMISSION TOOLS"

Samantha Phillips
5 years ago
Views:

1 172 Phone: Fax: STRAIN LINK STICK Used as insulation between rope blocks and a hot line wire grip For deadend structures and running corners Attached to conductor close to wire tong to support conductor loads Also used to support middle conductor on H frame structures during insulator or crossarm changes Cat.No. O.A. Lgth PoleDia & Lgth Jaw Opening Min Max Work Load Lbs. Wgt Lbs. H "-3" 1.5"x2' , H '-9" 1.5"x4' , H '-9" 1.5"x6' , H '-9" 1.5"x8' , H '-9" 1.5"x10' , H '-9" 1.5"x12' , H4717 5' 1.5"x4' , H '-2" 1.5"x6' , H4718 5'-2" 1.5"x4' , H '-2" 1.5"x6' , H '-2" 1.5"x8' , H '-2" 1.5"x10' , H '-2" 1.5"x12' , SPIRAL LINK STICK Replaces strain link stick when lineman cannot safely install one by hand A lifting eye on the head ferrule enables the lineman to guide the spiral link stick to the conductor with a hotstick 1-1/14" Epoxiglas pole Pole Dia. x Max. Conductor Work Load H x kcmil ACSR 3500 lb. C x kcmil ACSR 3500 lb. ROLLER LINK STICK For spreading and holding conductors at midspan when relocating a pole Applied to conductor at pole and pulled to position by hand line on butt ring Handline should be secured by a temporarily installed screw anchor or other fixed object Rotating the pole closes the hook, leaving head free to roll along conductor ADJUSTABLE STRAIN POLES Pole Dia. x Max Voltg Insulatd Section O.A. Lgth Wgt Lbs. C ' Strain Pole 72.5kV 36" 7'-8" 18 C ' Strain Pole 169kV 48" 8'-8" C ' Strain Pole 242kV 63" 9'-11" 19.5 C ' Strain Pole 302kV 84" 11'-8" C ' Strain Pole 362kV 102" 13'-2" C ' Strain Pole 552kV 135" 15'-11" C ' Strain Pole 765kV 180" 19'-8" 26.5 Accessories Max. Conductor Work Load H " 1.25" x 4' 605 kcmil ACSR 1000 H " 1.25" x 6' 605 kcmil ACSR 1000 E P For many transmission and EHV maintenance applications Helps support conductors while insulators are removed Used with yoke plates and hook assemblies at the conductor Five stainless steel crosspins are located at 6" intervals on the 2" diameter Epoxiglas poles 12" Strain Jack included with each Strain Pole E P 2" Adjustable Pole Clamp 2 E P 12' Acme-thread Strain Jack 3 V P 24' Acme-thread Stain Jack 4 V " Acme-thread Strain Jack 6 E P Steel Through Pin P Klik Pin.06

Phone: 800-323-6606 Fax: 847-488-1285 www.hilineco.

strings where conductor end hardware permits attachment Max load rating is 15,000 lb per insulator string Pole Distance Between Yokes Weight C401-2174 6' 49" - 81" 81 lb C401-2175 7' 59" - 93" 83 lb

TWO-POLE YOKES C401-1720 C401-1721 Can be ordered separately to make two pole strain carriers.

end Max load rating is 6,500 lb per insulator string Pole Distance Between Yokes Weight C401-0411 6' 47.5" - 81" 82 lb C401-0410 8' 71.

2 Phone: Fax: HEAVY DUTY TWO-POLE STRAIN CARRIERS Relieve strain from an insulator string to permit removal from energized lines Normally used on a single string of insulators Also used for multiple strings where conductor end hardware permits attachment Max load rating is 15,000 lb per insulator string Pole Distance Between Yokes Weight C ' 49" - 81" 81 lb C ' 59" - 93" 83 lb C ' 74" - 108" 85 lb C ' 95" - 129" 89 lb C ' 113" - 147" 95 lb C ' 146" - 180" 97 lb C ' 191" - 225" 105 lb TWO-POLE STRAIN CARRIER ACCESSORIES TWO-POLE YOKES C C Can be ordered separately to make two pole strain carriers. Fabricated of high strength aluminum plate Max load rating 15,000 lb per insulator string Weight C Conductor End Yoke Assembly (includes hook and socket) C Structure End Yoke Assembly (includes chain and attach. hardware) 25 lb 20 lb DEADEND COMPRESSION YOKE ASSEMBLY STD DUTY STRAIN CARRIERS Same basic use as the two pole strain carrier Distribution strain carrier has a compression deadend yoke at the hot end Max load rating is 6,500 lb per insulator string Pole Distance Between Yokes Weight C ' 47.5" - 81" 82 lb C ' 71.5" - 105" 92 lb C Used with two pole strain carriers, these units grip compression sleeves over the compressed area, requiring no shoulder or adapter to pull against 11,000 lb max load (with 2" adjustable strain poles) Includes a hot link extension for 3/4" & 1" dia shank and 4 sets of shoes for conductor MCM ACSR TAKE-UP TRUNNIONS DEADEND SOCKET C Furnished with the two pole strain carrier For extension links with 7/8" shank and 1.5" collar E P E P T Bronze alloy and ball thrust bearing construction Equal the capacity of all Chance yokes Requires M19483 Ratchet Weight E P (1) Large Trunnion 3.5 lb E P (1) Small Trunnion 2 lb T Trunnion Gauge for 3/4" acme threads.5 lb

174 Phone: 800-323-6606 Fax: 847-488-1285 www.hilineco.

insulators Should be purchased in pairs to fit specific yoke plate construction Same yoke assemblies can be used on both the hot and cold end of tne insulator string as they hook into the yoke plate

C401-1717 Rectangular or Triangular Plates up to 3/4" thick 25 lbs.

3 174 Phone: Fax: SINGLE-POLE STRAIN CARRIER YOKES C STRAIN POLES H C C Can be used with adjustable strain poles to remove the strain from one string of multiple strings of deadend insulators Should be purchased in pairs to fit specific yoke plate construction Same yoke assemblies can be used on both the hot and cold end of tne insulator string as they hook into the yoke plate hardware Rated at 15,000 lb max load per insulator string Fits Yoke Plates Wgt C Flat Plates up to 3/4" thick 25 lbs. C Flat Plates up to 1" thick 25 lbs. C Rectangular or Triangular Plates up to 3/4" thick 25 lbs. For bundle conductor yoke plates Accommodate a wide range of yoke plate designs and hole spacings Commonly used in deadend rigging, for "V" strings and restrained angles, poles offer two clevis lengths and overall lengths 12,000 lb max load capacity with a 1" wide clevis for aluminum conductor yoke plates C Working Weight H Butt Swivel, Clevis 3.35" x 1" 113" 17 lb C Butt Swivel, Clevis 1.56" x 1" 113" 14 lb C Butt Swivel, Clevis 1.56" x 1" 134" 15 lb PSC Clevis, Clevis 1.56" x 1" 113" 14 lb PSC Clevis, Clevis 1.56" x 1" 134" 15 lb STRAIN POLE ACCESSORIES Strain Jacks Tongue Type Strain Jacks Clevis Type Strain Jacks M Ratchet Wrench Weight M Ratchet Wrench 2.2 lb E P 12" Strain Jack, Tongue Type 3 lb V P 24" Strain Jack, Tongue Type 4 lb V " Strain Jack, Tongue Type 6 lb H " Clevis Ratchet Screw 5.5 lb H " Strain Jack, Clevis Type 8 lb H " Strain Jack, Clevis Type 10 lb SPM Acme Eyenut 1 lb

swinging corner construction, and to raise the insulators on long suspension units Deep trough design holds insulator string securely Used to make insulator changes by supporting the string while

4 Phone: Fax: TRANSMISSION INSULATOR CRADLE EHV TROUGH-DESIGN INSULATOR CRADLE For making insulator changes on lines energized up to and including 500KV Also for lowering insulator strings on deadend and swinging corner construction, and to raise the insulators on long suspension units Deep trough design holds insulator string securely Used to make insulator changes by supporting the string while damaged insulators are replaced Also used to pivot the string so that it may be removed and lowered to the ground On deadends or running corners, cradles are used in conjunction with strain carriers In straight suspensions, they are used with various link sticks or adjustable strain pole assemblies H HOOK Capacity Weight H ' 10-10" Insulators H ' 14-10" Insulators 24 H ' 18-10" Insulators 27 STATIC GROUND BAIL 10" Insulator Capacity Wgt lbs H ' Insulator Cradle C "-4" Insulator Cradle H Insulator Cradle Carrier Eliminates electrostatis charge when working insulator strings Drains off charge from insulator string to tower leg 6' of No. 2 grounding cable is attached Flat face clamp at one end of grounding cable Adjustable jaws fit insulator caps 2.5" - 6" Weight HG with Eyescrew Clamp 5 lb C with "T" Handle Clamp 5 lb

176 Phone: 800-323-6606 Fax: 847-488-1285 www.hilineco.

bundle access lower string Shipped with bridle for attaching to swivel boom, an insulator retaining plate, and either 15" or 31" hook assemblies 500 lb max load for 9' cradle 1000 lb max load for 13'

C401-0354 16 Cradle, 15 Support Hooks 125 lb C401-0355 16 Cradle, 31 Support Hooks 131 lb C401-0361 (1) 15 Support Hook 10 lb C401-0362 (1) 31 Support Hook 12 lb C401-0455 Insulator Retaining Plate 8

5 176 Phone: Fax: EHV SIDE OPENING INSULATOR CRADLE SUSPENSION YOKES C For selective removal of any one string in deadend bundles, double, triple or quad Eliminates the need for removing top strings in bundle access lower string Shipped with bridle for attaching to swivel boom, an insulator retaining plate, and either 15" or 31" hook assemblies 500 lb max load for 9' cradle 1000 lb max load for 13' & 16' cradles Wgt C Cradle, 15 Support Hooks 93 lb C Cradle, 31 Support Hooks 98 lb C Cradle, 15 Support Hooks 119 lb C Cradle, 31 Support Hooks 124 lb C Cradle, 15 Support Hooks 125 lb C Cradle, 31 Support Hooks 131 lb C (1) 15 Support Hook 10 lb C (1) 31 Support Hook 12 lb C Insulator Retaining Plate 8 lb C C yoke is used with the H2947 series adjustable strain poles C yoke is used with clevis strain poles 15,000 lb max load per insulator string Has two spring loaded latches which engage and lock the pole clamp into position on the yoke, 26" apart center to center Wgt C Strain Pole Yoke - 3.5" Swivel Saddle 26 lb C Clevis Pole Yoke - 3.5" Swivel Saddle 23 lb ADJUSTABLE HOOK ASSEMBLY M A direct method of relieving load on suspension string Conductor clamp has contoured seat with a trapping gripper and is operated by an eyescrew Conductor range is 1-1/8" - 2-1/2" dia Can be positioned every 6" on the strain pole 3,500 lb max load J-HOOK ASSEMBLY SUSPENSION LINK STICKS C For removal of deadend insulator strings Plastisol-covered steel hook swivels on end of a 2" x 36" Epoxiglas pole 2.5" diameter pole clamp at the top end Useful in removing bottom string in a 3 bundle insulator string Rated working load: 250 lbs per hook These sticks are designed for use on conductors from 1" - 2-1/2" dia. and can be used with various types of takeup devices at the structure end. The lip of the hook, actuated by an eye screw, swivels to accommodate various conductor sizes. Max load: 6,500 lbs. Pole Dia & Lgth Weight H /2" x 84" 14 lb H /2 x 96" 16 lb H /2' x 114" 18 lb

a support for strain poles Yoke legs fit most tower structure configurations Max

yoke to the double plank crossarms and are adjustable to 9", 11", 13" Vertical

Swivel castings in end of yoke for proper alignment of strain poles Load rating

This bracket is used with steel arm yoke (above) where the steel arm is not

TOWER HANDLINE GIN M1979 3' x 3" x 1/4" with an aluminum-welded end-plate

handlines from dragging over tower structure Hook adjustment will fit tower angle

SUSPENSION INSULATOR TOOL Rolls a string of suspension insulators into the

tower arm using tower type wire tong saddles H4723-2 Fork Suspension Tool Attach.

5" x 12') H4723-4 Single Trolley Wheel with 2.

5" Pole Clamp HOT STICK TENSION PULLER H4723-2 H4723-4 C400-0152 Equipped with

on each end for positive hotstick operation Spring loaded gate rotates 135

5KV Hot Stick Tension Puller C400-0575 69KV Hot Stick Tension Puller C400-0600

6 Phone: Fax: STRUCTURE YOKES STEEL TOWER YOKE H Fits over tower arm, serving as a support for strain poles Yoke legs fit most tower structure configurations Max load: 12,000 lb WOOD OR H-FRAME TOWER YOKE C Two clamp bolts secure the yoke to the double plank crossarms and are adjustable to 9", 11", 13" Vertical take-up 9"-12" Max load: 12,000 lb STEEL ARM YOKE C Use on steel pole arm Swivel castings in end of yoke for proper alignment of strain poles Load rating dependent on angle of end plates Max load: 15,000 lb STEEL ARM BRACKET T This bracket is used with steel arm yoke (above) where the steel arm is not equipped with an end plate. TOWER HANDLINE GIN M1979 3' x 3" x 1/4" with an aluminum-welded end-plate securing bronze, free-swivel butt ring Snatch blocks hooked into butt ring keep handlines from dragging over tower structure Hook adjustment will fit tower angle from 1-3/4" x 1-3/4" up to 6" x 6" 21" long with a 500 lb max load TROLLEY POLE SUSPENSION INSULATOR TOOL Rolls a string of suspension insulators into the structure so that units can be replaced Can be fastened horizontally under the tower arm using tower type wire tong saddles H Fork Suspension Tool Attach. for 2.5" Pole H Trolley Pole (2.5" x 12') H Single Trolley Wheel with 2.5" Pole Clamp C Tandem Tolley Wheel with 2.5" Pole Clamp HOT STICK TENSION PULLER H H C Equipped with rings for use with a Grip-All Clampstick or with rubber gloves Non-swiveling hook on each end for positive hotstick operation Spring loaded gate rotates 135 degrees left or right from closed position C KV Hot Stick Tension Puller C KV Hot Stick Tension Puller C Tie Back Clamp (# kcmil ACSR) C Tension Puller Hook Adapter INSULATOR LIFTERS PSC This high-density, 12.6" dia. bell lifter is made of sturdy polyethylene. 400 lb Test Load Wgt: 13.5 lbs. LH95 This 10" dia. bell lifter is rubber coated to protect porcelain insulators. 8,000 lb Test Load Wgt: 65 lbs. PSC LH95

Transmission Tools. Catalog 2250 May Transmission Tools Phone: Web: hubbellpowersystems.

Transmission Tools. Catalog 2250 May Transmission Tools Phone: Web: hubbellpowersystems. Transmission Tools Catalog 2250 May 2016 Transmission Tools 2250 May 2016 Page 2251 STRAIN LINK STICK Tested per OSHA & ASTM F711 Used as insulation between rope blocks and a hot line wire grip For deadend