AAB Solar Street Light

Size: px

Start display at page:

Download "AAB Solar Street Light"

Dwayne Perry
5 years ago
Views:

1 AAB Solar Street Light AAB-I & AAB-IS series Instruction Manual 1.Suit for bellow 20W of AAB-I and AAB-IS series 1.1 Press ON/OFF on controller 1.2 Factory standard lighting mode: A. 100% if people come close,30% far away for first 0-4hrs after dark. B. 70% if people come close,30% far away from 5-7hrs after dark. C. 50% if people come close,20% far away from 8-10hrs after dark. D.30% if people come close,10% far away from 11-12hrs after dark. Working methord 1-12hrs repeat after dark or solar panel been covered. PS: Smart Control on batteries, power would be adjusted automatically 1.3 Buttons instruction as following picture

2.Suit for above 20W of AAB-I and AAB-IS series 2.1 Press ON/OFF on small remote controller 2.2 Factory standard lighting mode: A. 100% if people come close,30% far away for first 0-4hrs after dark.

2 2.Suit for above 20W of AAB-I and AAB-IS series 2.1 Press ON/OFF on small remote controller 2.2 Factory standard lighting mode: A. 100% if people come close,30% far away for first 0-4hrs after dark. B. 70% if people come close,30% far away from 5-7hrs after dark. C. 50% if people come close,20% far away from 8-10hrs after dark. D.30% if people come close,10% far away from 11-12hrs after dark. Working methord 1-12hrs repeat after dark or solar panel been covered. PS: Smart Control on batteries, power would be adjusted automatically 2.3 Picture of sensor and remote controller 3. LED Indicators 1 PV Indicator Color Indication Working State Green On Solid PV is charging Battery Green Flash Fast Battery Over Voltage,refer to Trouble shooting. --- OFF PV voltage is low

3 2 Battery Indicator Color Indication Working State Green On Solid Battery is Normal Green Flash Battery is full Yellow On Solid Battery is under voltage Red On Solid Battery is over-discharged, turn off Load auto 3Load Indicator Color Indication Working State Yellow On Solid Load is ON -- OFF Load is off Yellow Flash Fast Load short circuit or open circuit Yellow Flast Slow Load led chaps series number is too low Or overload limited power output

4 4.Small remote controller manual for power above 20W of AAB-I & AAB-IS 1. OFF: The ON/OFF lamp button(sleep button),after the lamp is off(in sleep mode),you can press button again to light up the lamp(out of sleep mode to active battery),or the battery can be activated automatically by continuous light from solar panel for 10 minutes. 2. DEMO: The button of demonstration test uses,after press,it will light up the lamp from the maximum current to the minimum current within 10 seconds. Work Mode: 3. L button: Light control mode, woke mode according to the setting current (running current is sensor current,no sensor current NOT work), e.g. the whole night is 12 hours, if the setting time less than 12 hours,the rest of the time will run with the minimum current as setting in remote control to finish the whole night, if the setting time over than 12 hour,it will cut off the lamp after 12hours(the day is bright then). 4. T button Time control+light control mode: the lamp will be on by light control,and running as the time that you have set in the all time periods. For the current,it will run as sensor current(no sensor 5. M button The motion sensor mode, it will work according to the setting for working time and current. In the whole process, motion sensor is used to detect coming people, when people come,the lamp will work as setting sensor current,when people left,the lamp will work as setting NO sensor current,(sensor current will last for 10 seconds when people come as default,during the time,if another people come again,the time will be recalculated again for another 10s). 6. T+M button Time control+motion Sensor mode,the first two time periods(total have 4 time periods),the lamp will be working according to the setting with motion sensor current(no sensor current will not work in this two periods). After these two periods finished,enter into Motion sensor work mode, motion sensor is used to detect coming people, when people come,the lamp will work as setting sensor current,when people left,the lamp will work as setting NO sensor current,(sensor current will last for 10seconds when people come as default,during the time,if another people come again,the time will be recalculated again for another 10s).

5 5.Installing way A:AAB-I 10W-40W & AAB-IS 15W-60W Pole dia.:60m B: Suit for AAB-I 15W-40W C: AAB-IS Installing way 6.Height of Installing and working condition 6.1 Height of installing around 3M for power bellow 20W, 5M for power around 25W-60W. 6.2 Working Temperature: -20 to +70degree

6 AAB 太阳能灯 AAB-I 10W 认证 : 有的认证都写上去 AAB Solar Street Light AAB-I 10W Certificate:EMC/ROHS/LVD/FCC 英文

7 中文 AAB 磷酸铁锂电池 12.8V 12A 生产日期 : 使用寿命次环境温度 : 充电 0-70 度放电度警告 : 严禁短路投入水中超温使用防止撞击不要拆 xei 及刺穿以上均可能引起爆炸等危险

8 英文 AAB Lithium iron phosphate Battery(LiFePO4) 12.8V 12A Manufacture date: Lifespan: times Ambient Temperature:charge 0-70degree discharge degree Warning/Strictly prohibit: circuit Put into the water Overtemperature use Prevent impact Do not disassemble and pierce. All of above may cause explosion and other dangers. Short

AAB Solar Street Light

AAB Solar Street Light AAB-I & AAB-IS series Instruction Manual 1.Suit for bellow 20W of AAB-I and AAB-IS series 1.1 Press ON/OFF on controller 1.2 Factory standard lighting mode: A. 100% if people come