POWER BANK 规格书 POWER BANK SPECIFICATION. Cell(1S2P)+Housing 电芯 (1S2P)+ 胶壳 MB 组合类型 : Product Model. 成品型号 : Pack Capacity (mah) Pack Type

Transcription

1 POWER BANK 规格书 POWER BANK SPECIFICATION Pack Type Cell(1S2P)+Housing 组合类型 : Product Model 成品型号 : Pack Capacity (mah) 电芯 (1S2P)+ 胶壳 MB-5200 成品容量 (mah): 6000 Customer Code 客户代码 : Total Page 文件页数 : 9 Registered 编制 Checked 审核 Approved 批准 Dept. 部门 QA Dept 品质 R&D Dept 研发 Approved 批准 Customer Approve 客户确认 Signature 签名 Date 日期 File NO/ 文件编号 :BT-0176 版本 REV:A IES-QR-R-028 A0 Page 1 of 9

2 Content 1 Modified List Scope... 錯誤! 尚未定義書籤 3 Battery Appearance arts Identification Method of Charging the Product Method of Charging Digital Products Battery Indicator Mechanical Characteristics Safety Characteristics Standard Environmental Test Condition Free-responsibility Declaration...9 File NO/ 文件编号 :BT-0176 版本 REV:A IES-QR-R-028 A0 Page 2 of 9

3 1 Modified List Product Modified Record List Revision Date Mark Modified content Approved by A / FIRST RELEASE / File NO/ 文件编号 :BT-0176 版本 REV:A IES-QR-R-028 A0 Page 3 of 9

4 2 Scope This product is a multi-functional portable power with built-in environment-friendly and high safety lithium polymer battery. It is very convenient and practical for using. No matter where you are, you can timely charge your ipad, iphone, MP4, and other digital products, even without AC adapter on hand. Please read the instructions carefully before using. 3 Battery Appearance File NO/ 文件编号 :BT-0176 版本 REV:A IES-QR-R-028 A0 Page 4 of 9

5 4 Arts Identification 5 Method of Charging the Product Charge the product with the adapter or computer USB port. (Please select the adapter or USB port with output DC5.0V±0.3V and above 1A. If out of the range, the charging time will be prolonged.) 5.1. Connect the power bank with the adapter or computer USB port by USB data cable 5.2. Turn on the power and begin to charge the product. In charging, the instructor light is blinking cyclically and all four lights will be on if full of power. Charging connection is shown as below: File NO/ 文件编号 :BT-0176 版本 REV:A IES-QR-R-028 A0 Page 5 of 9

6 6 Method of Charging Digital Products 6.1. Choose correct tip or use the original data cable of your digital products to connect the portable power bank with the digital products Press the button to charge your digital products and the indicator lamp is lighting. Power-up schematic diagram as below: 6.3. Note: Check the charging voltage before charging your digital products. It will be broken or couldn t power up the digital products if the output voltage of the portable power bank doesn t match the charging voltage of digital products The product can charge ipad, iphone and other digital products at the same time. It will stop output and access hibernation model when the digital products are fully charged. 7 Battery Indicator 7.1. Charging instructions: The power bank will be charged when connected with the adaptor or computer USB port. The two USB ports of the power bank are ready for charge, as well as LED lighting can measure the battery power. File NO/ 文件编号 :BT-0176 版本 REV:A IES-QR-R-028 A0 Page 6 of 9

7 90%-100% --- ALL LED lighting 60%~90% --- LED 1 to 3 lighting, LED 4 flashing 40%~60% ---- LED 1 to 2 lighting, LED 3 flashing 20%~40% LED 1 lighting, LED 2 flashing 0%~20% LED 1 flashing 7.2. Discharge Instructions: Press the switch to charge the electrical appliances connected with the power bank. The LED lights indicate the battery power. The power bank will automatically hibernate when electrical appliances are full charged or no load is available LED flashlight Press the side button for 2-3S to turn on the flashlight, and another 2-3S to turn it off Product Specifications: 1) Built-in Lithium Polymer Battery Pack Specification: 6000mAh/3.7V 2) Input Voltage: DC 5.0V±0.3V 3) Input Current: Max 1200mA 4) Output Voltage: DC4.85V -5.25V (no load) 5) Output Current: 1000mA/2100mA 6) Cycle Life: 500 times 7) Weight: approx. 164g 8) Max Size: 96mm 62mm 23mm 9) With adapter charging time: about 7 hours 10) With over charge, over discharge, over current and short circuit protection 11) Temperature and humidity: This product can work properly when the temperature between 0-45, relative humidity 85%, atmospheric pressure 86kpa-106kpa. 12) The conditions of transportation and storage: When this product is stored or transported, the temperature should be between Relative humidity should be 75%. Higher temperature, lower temperature or humidity are harmful for this product, and may result in serious result. 8 Mechanical Characteristics NO Item Standard Test method File NO/ 文件编号 :BT-0176 版本 REV:A IES-QR-R-028 A0 Page 7 of 9

8 1 Vibration Impacting 2 Testing 3 Free fall The battery shall not rupture, smoke, catch fire, vent or leak and voltage of each cell should not be lower than 3.0V. After standard charge, the cell fixed in the vibration table and subjected to vibration cycling that the frequency is at the rate of 1Hz per minute between 10Hz~ 55Hz, the excursion of the vibration is 1.6mm.The cell shall be vibrated for 30 minutes per axis of XYZ axes. The change of vibration frequency is 1Hz per minute. After vibration, the battery will be impacted 1000±10 times (60±20 times per minute) with the acceleration of 100m/s and the pulse lasting time is 16ms. After impacting test, the battery will drop free five times in three mutually perpendicular directions from the height of 1.0m onto a hard board with the thickness of 20mm. 9 Safety Characteristics No Item Standard Test method Overcharge Performance Over Discharge Performance Short Circuit at Room Temperature No fire, No explosion After standard charge, charge at 3C 5A till the voltage of each battery reaches 10.0V, then observe the appearance of the battery. Store the battery at 20 ±5 after standard charge, discharge at 0.3C5A till the voltage reaches 0V. After standard charge,let the battery located in a fume hood and short-circuited by connecting the positive and negative terminals with an external load of less than 50 mω till the battery s case temperature has returned to near ambient temperature. 10 Standard Environmental Test Condition Unless otherwise specified, all tests stated in this Product Specification are conducted at below conditions: Temperature: 20±5 Humidity: % RH Atmospheric Pressure: 86KPa~106 kpa Notes 1. Please do not use sharp objects scratching the surface of the product housing. 2. Please use the adapter with output voltage of DC5.0±0.3V or computer USB port to charge the product. 3. Do not put it in water, fire, high temperature and low temperature environment, do not give it to children; keep children far away from the accessories. File NO/ 文件编号 :BT-0176 版本 REV:A IES-QR-R-028 A0 Page 8 of 9

9 4. Prohibit the demolition and alteration of the product in order to avoid the damage of the product's protection devices. Otherwise it may cause the danger of the heat, fire or explosion of the battery. 5. When the product charges the digital products, do not force the plug, so as to avoid the damage to ports which may lead to the poor contact. 6. If the product is not in the constant using, there will be the self-discharge less than 5%. Please make sure to charge the product fully at least once every three months. 7. If the customer does not use or place this product correctly, it may result in the reduction of product life or any damages. It is the customer s personal responsibility, not a factory warranty liability or responsibility. Please kindly understand. 8. As for the self-consuming of the materials, it is not belonging to the factory warranty liabilities, please kindly understand! 9. All accessories in this package only use for this product. 10. The developer and manufacturer of this product have the right of interpretation and determining and revising on all of the above terms. 11 Free-responsibility Declaration Before using the battery, you should read the specifications, usage instruction and some attentions carefully to learn its application method and areas. If the phenomenon such as error using method or wrong circuit connection, or input power data, working index are in consisted with the specifications happen and cause damage to production,circuit and its accessories, we are not responsible for it. Any matters that this specification does not cover should be conferred between the customer and IES. File NO/ 文件编号 :BT-0176 版本 REV:A IES-QR-R-028 A0 Page 9 of 9