Regenerative Principle

Transcription

1

2

3 Regenerative Principle Rotation In Out Air Flow The impeller blades passing the inlet port draw air or other gases into the blower. The impeller blades then, by centrifigal action, accelerate the air outward and forward. Here the regenerative principle takes effect as the air is turned back by the annular shaped housing to the base of the following blades, where it is again hurled outward. Each regeneration imparts more pressure to the air. When the air reaches the stripper section at the outlet (the stripper is the part of the blower located between the inlet and the outlet in which the annulus is reduced in size to fit closely to the sides and tips of the impeller blades), the air is stripped from the impeller and diverted out of the blower. The pressures or vacuums generated by each spinning, non-contacting, oil-free impeller are equal to those obtained by many larger multi-stage or positive displacement blowers. USA: Europe: Asia:

4 Table of Contents A: Nine Major Blower Application Areas B: Product Dimensional Listing C: Industrial / Chemical Processing Blowers DR HP Regenerative Blower C1 DR P15 4. / 6. HP Regenerative Blower DR S15 4. HP High Pressure Regenerative Blower C57 C59 D: Environmental / Chemical Processing Blowers EN 11 & CP 11 D1 DR 83 C3.5 HP Sealed Regenerative w/explosion-proof Motor.125 HP Regenerative Blower EN 33 & CP 33 DR 11 & CP 11 C5.5 HP Sealed Regenerative w/explosion-proof motor.33 HP Regenerative Blower EN 44 & CP 44 DR 22 & CP 22 C7 1. HP Sealed Regenerative w/explosion-proof Motor.33 HP Regenerative Blower EN 454 & CP 454 DR 33 & CP 33 C9 1.5 HP Sealed Regenerative w/explosion-proof Motor.33 HP Regenerative Blower EN 55 & CP 55 DR 353 & CP 353 C11 2. / 2.5 HP Sealed Regenerative w/explosion-proof Motor. HP Regenerative Blower EN 513 & CP 513 DR 44 & CP 44 C HP Sealed Regenerative w/explosion-proof Motor 1. HP Regenerative Blower EN 523 & CP 523 DR 454 & CP 454 C15 3. HP High Pressure Sealed Regenerative w/explosion-proof Motor 1.5 HP Regenerative Blower EN 6 & CP 6 D15 DR 55 & CP 55 C17 5. HP Sealed Regenerative w/explosion-proof Motor 2. / 3. HP Regenerative Blower EN & CP 633 D17 DR 513 & CP 513 C HP High Pressure Sealed Regenerative w/explosion-proof Motor 1.5 HP Regenerative Blower EN 656 & CP 656 D19 DR 523 & CP 523 C21 3. HP Sealed Regenerative w/explosion-proof Motor 3. HP High Pressure Regenerative Blower EN 7 Single-Phase and CP Options D21 DR 555 & CP 555 C23 Sealed Regenerative Blower w/explosion-proof Motor 3. / 4. HP Regenerative Blower EN 7 & CP 7 D23 DR 6 & CP 6 C25 3. / 5. HP Sealed Regenerative w/explosion-proof Motor 3. / 5. HP Regenerative Blower EN 88 Single-Phase and CP Options D25 DR 633 & CP 633 C27 Sealed Regenerative Blower w/explosion-proof Motor 3. / 4. / 5. HP Regenerative Blower EN 88 & CP 88 Three-Phase D27 DR 656 & CP 656 Sealed Regenerative Blower w/explosion-proof Motor C29 3. / 4. / 5. HP Regenerative Blower EN 833 & CP 833 D29 DR 7 & CP 7 C HP High Pressure Sealed Regenerative w/explosion-proof Motor 4. / 5. HP Regenerative Blower EN 858 & CP 858 D31 DR S7 C / 1. HP Sealed Regenerative w/explosion-proof Motor 7.5 HP High Pressure Regenerative Blower EN 99 & CP 99 D33 DR 88 & CP 88 C35 1. / 15. HP Sealed Regenerative w/explosion-proof Motor 5. / 7.5 HP Regenerative Blower EN 979 & CP 979 D35 DR 833 & CP 833 C37 2. HP Sealed Regenerative w/explosion-proof Motor 7.5 / 1. HP Regenerative Blower EN 14 & CP 14 D37 DR 858 & CP 858 C39 2. / 3. HP Sealed Regenerative w/explosion-proof Motor 7.5 / 1. HP Regenerative Blower DR P9 C41 E: Remote Drive (Motorless) Blowers MF573RD E1 15. / 2. HP Regenerative Blower SL2RD E2 DR S9 C43 DR/EN/CP 44RD E3 15. / 2. HP High Pressure Regenerative Blower DR/EN/CP 55RD E4 DR 99 & CP 99 C45 DR/EN/CP 513RD E5 1. / 15. HP Regenerative Blower DR/EN/CP 523RD E6 DR 979 & CP 979 C47 DR/EN/CP 6RD E7 15. / 2. HP Regenerative Blower DR/EN/CP 656RD E8 DR 1233 & CP 1233 C49 DR/EN/CP 7RD E9 2. HP High Pressure Regenerative Blower DR/EN/CP 858RD E1 DR P13 C51 DR/EN/CP 99RD E11 2. / 3. HP Regenerative Blower DR/EN/CP 979RD E12 DR S13 C53 DR/EN/CP 1233RD E13 2. / 3. HP High Pressure Regenerative Blower DR/EN/CP 14RD E14 DR 14 & CP 14 C55 2. / 25. / 3.HP Regenerative Blower D3 D5 D7 D9 D11 D13 USA: Europe: Asia:

5 Table of Contents F: Application Specific Blowers Minispiral Insrument Grade Regenerative Blower Minispiral MDC Variable Flow Regenerative Blower Minispiral 12/24V HDC Variable Flow Regenerative Blower Minispiral 12V HDC Extra Flow / Extra Wide Fat Boy Variable Flow Regenerative Blower SPIRAL Simplex SL2 Insrument Grade Regenerative Blower SPIRAL Duplex SL4 Insrument Grade Regenerative Blower SPIRAL Duplex SL5 Insrument Grade Regenerative Blower Nautilair DR 44/454/55/513/656 Spa Blowers DR 1RDNT/SS1RDNT/HS 1RDNT Remote Drive (Motorless) Blowers MD 11 Magnetic-Drive Regenerative Blower GVR313 Regenerative Blower G: Accessories Filtration - Inlet Filter (Single Connection) Filtration - Inline Filter (Dual Connection) Filtration - Filter Silencers (Single Connection) Filtration - Filter Element Filtration - Moisture Separator Measurement - Air Flow Meter Measurement - Digital Flowmeter Noise Reduction - Sound Attenuating Enclosure Noise Reduction - Inlet/Outlet Muffler (Single Connection) Noise Reduction - Inline Muffler (Dual Connection) Protection - Relief Valve - Mechanical Protection - Pressure Regulating Diaphram Valve Protection - Gauges System - Variable Frequency Drive System - Air Knives System - 5 Way, 3 Port, 2 Position Diverter Valve System - Air Flow Switch Pressure & Vacuum Arrangements H: Motor Blower Options I: Application Engineering Basics F1 F3 F5 F7 F9 F11 F13 F15 F17 F19 F21 F23 G1 G2 G3 G4 G5 G7 G9 G1 G11 G12 G13 G14 G15 G16 G17 G19 G21 G22 USA: Europe: Asia:

6 Nine Major Blower Application Areas Your own imagination and knowledge are probably the best source of in-plant and on-site applications for ROTRON regenerative blowers. This guide will help to pinpoint and stimulate your consideration of the many alternative sources we provide to replace costly and maintenance intensive suction and pressure units and systems. The nine major application groups are listed and a cross reference of the most common applications by industry will help you identify both identical and similar applications in your industrial operations. Application 1: Air-Assisted Breathing Manufacturing PARP Respiration Mining PARP Respiration Nose Mouth Throat Application 2: Air-Assisted Inflation or Support Part Material Handling Air Slides Air Tables Carbon Black Car Unloading Blower Flotation Tables Web Air Bags Air Film Support Paper Processing Flotation Tables Forming Bar Sheet Fluttering Turn Bars Textile Garment Flotation Tables Air Slides / Air Tables Plenum Pneumatic Suction Cups Blower Work General Parts Pick-Up Blower Box Vacuum Manipulator Blower Blower Turning & Forming Bars Application 3: Air-Assisted Vacuum Pick-Up or Hold-Down Work General Parts Hold-Down Flotation Tables Work Table Block Water Pollution Control Pollution Containment Waterway Management Manufacturing Bag Filling Equipment Cutting Tables Packaging Equipment Vacuum Manipulators Corrugated and Paperboard Boxes Flexible Packaging - Paper, Plastic, Aluminum Foil, Textile Packaging and Steel Strapping Rigid Packaging Beverage Containers Cosmetic and Toiletry Containers Blister Packs Pharmaceutical Packaging Food Packaging Sterile Medical Device Packaging Labels Pressure Sensitive Tape Paper or Plastics Handling Cutting Tables Diaper Making Equipment Printing Presses Blower Carboard Case Erector Textile Garment Cutting Tables Yarn Guiding and Tensioning Yarn Aspiration USA: Europe: Asia: A 1

7 Nine Major Blower Application Areas Application 4: Air & Gas Sampling, Boosting, or Circulating Blower Fluid Bed Regeneration Stack Lens Lens Light Beam Blower Blower Transmissometer Lens Purging Instrument Air Pollution Control Air Sampling Air Stream Release Monitoring Fire Prevention Air Sampling Flue Gas Sampling Foundry Combustion Air Boost Instrumentation Glove Box Pressurizing Incubator Air Circulation Weather Measurement Sampling Pharmaceutical Clean Room Air Circulation Oxygen Generator Plastics Handling Desiccant Dryer Bed Regeneration Blower Natural Gas Natural Gas Furnace Natural Gas Boost Minispiral Air & Gas Sampling Manufacturing Combustion Air Boost Natural Gas Boost Oil Demisting Gas Combustion Chamber Combustion Air Boost Application 5: Electronic Cooling Blower Electronics Electronics Instrumentation Engine/Motor Cooling Film Development System Cooling Lamp Bank Cooling Small Enclosure Cooling Blower Blower Pressurized Cabinet Soil Vapor Extraction & Landfill Gas Recovery Vacuum Pull-Through Cabinet Application 6: Gas, Vapor, & Fume Recovery, Venting, & Treatment Blower Treatment System Blower Scrubber Vent Header Off-Gassing Chemical Tank Agricultural Methane Gas Recovery Chemical Processing Vent Header Off-Gassing Environmental Gasoline Vapor Recovery Lagoon Gas Recovery Landfill Gas Recovery Radon Gas Collection Soil Vapor Extraction Foundry Lost Foam Off-Gassing Pharmaceutical Sterilization Gas (ETO) Recovery Refineries Centrifuge Venting Water Pollution Control Digester Gas Collection Blower Filter Fume & Smoke Removal Blower Flame Digester Digester Gas Collection Manufacturing - Plant Services Cabinet Fume Venting Environmental Test Chamber Venting Laser Smoke Removal Weld Smoke Removal USA: Europe: Asia: A 2

8 Nine Major Blower Application Areas Application 7: Solid Material Transporting, Separation, & Collection Pressure Blower Ejector Bin Rotary Airlock Cyclone Discharge To Process Dilute Phase Pneumatic Conveying Blower Pneumatic Tube Tube Carrier Foundry Sand Reclamation Manufacturing - Waste Control Chip, Dust, & Particle Removal Liquid & Solvent Removal Paper, Plastic Film, & Textile (Trim) Removal Material Handling Air Slides Blast Cleaning Dilute Phase Conveying Pneumatic Tube Packaging Bag Filling Blower Blower Collection Chamber Paper, Plastic, Film, & Textile (Trim) Removal General Material Separation & Collection Application 8: Parts Blow-Off & Drying Air Knife Hoist Air Knife Blower Blower Plating Tank Blower General Parts Blow-Off & Drying Solution Blow-Back Application 9: Solution & Media Agitation & Aeration Blower Blower Ground Level Soil Spargers Water Table Wastewater Treatment Tank Aeration Groundwater Sparging Aqueous Precision Cleaning Automotive Parts Drying Semiconductor Board Drying Food Processing Batter Blow-Off Bottle & Can Drying Label Drying Salt, Spice, & Flour Blow-Off Aquaculture Aquarium Fish Farm, Hatchery, & Pond Aeration Groundwater Sparging Manufacturing Concrete Fluid Bed Aeration Electroplating Tank Agitation Manufacturing Conveyor Belt Blow-Off Electroplating Fume Guiding Electroplating Parts Drying Electroplating Solution Blow-Back Flat or Irregular Metal Parts Drying Wire Drying Plating Bath Blower Electroplating Tank Aeration Blower Hot Tub Commercial Spa Aeration Material Handling Fluidized Beds Recreation Commercial Spa Aeration Product Bin Aerator (Air Pads) Blower Dock Water Management Boat, Dock, & Dam Face Deicing Blower Bin Pad & Fluidized Bed Aeration Boat & Dock Deicing Water Water Pollution Control UV Tube Agitation Watewater Filter Backwash Wastewater Treatment Tank Aeration USA: Europe: Asia: A 3

9 Product Dimensional Listing Blowers Shipping Wt (LBS) Carton Length (In) Width (In) Height (In) DR/EN 68 16/ / / / / / / / / / / / / / / S7 26/ / / / / S9 / P9 4/ / / / / S13 / P13 687/ S15 / P15 99/ Minispirals (SE2;12) 2/ Nautilairs (NC33) 18/ Spiral (SL2;4;5) 42/ Note: Model weight will vary by HP and voltage. Refer to individual specification sheets to verify. USA: Europe: Asia: B 1

10 Industrial / Chemical Processing Blowers AMETEK Dynamic Fluid Solutions ROTRON brand has long been a world leader in regenerative blower technologies, bringing regenerative advantages to a new level, providing quiet, maintenance-free, oil-free operation. Our industrial DR (Domestic Regenerative) blowers include: Rugged cast aluminum housing, cover, impeller, and muffler tower Removable cast iron flanges bolted to a sheet metal manifold TEFC motors on single-ended models, ODP motors on all double-ended models Carbon steel shaft and zinc plated hardware Permanently sealed motor bearings for 2,-25, hours life Our CP (Chemical Processing Regenerative) blowers include: Chem-Tough TM surface conversion corrosion resistant treatment for aluminum castings Teflon lip seal in a stainless steel case standard for leakage containment to 25 cc/min or less Chemical Duty motors with 33 stainless steel motor shafts Stainless steel hardware throughout Nickel plated flanges and muffler retainers USA: Europe: Asia:

11 Industrial / Chemical Processing Blowers DR HP Regenerative Blower DIA OUT O.D. (2) PLACES MM NOTES 1 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN..35 DIA. 9 (2) MTG. HOLES Part/ Model Number DR68DJ9Y Specification Units Motor Enclosure - Shaft Mtl. - TEFC - CS Horsepower - 1/8 Voltage AC 115/23 Phase - Frequency - Single - 6 Hz Insulation Class - B NEMA Rated Motor Amps Amps (A) 18/1.-.9 Service Factor - 1. Max. Blower Amps Amps (A) 1.18/.59 Locked Rotor Amps Amps (A) 8.7/4.35 NEMA Starter Size - / Shipping Weight Lbs 16 Kg 7.3 Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperaturs - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 1 USA: Europe: Asia:

12 Industrial / Chemical Processing Blowers DR HP Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant CE compliant - Declaration of Conformity on file Maximum flow: 13 SCFM Maximum pressure: 13.5 IWG Maximum vacuum: 13.5 IWG Standard motor: 1/8 HP, TEFC Cast aluminum blower housing, impeller & cover; slip-on steel flanges UL & CSA approved motor with permanently sealed ball bearings Inlet & outlet internal muffling Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) Various horsepowers for application-specific needs BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Cast iron (threaded) or face flanges for application-specific needs ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Switches - air flow, pressure, vacuum, or temperature External mufflers for additional silencing Air knives (used on blow-off applications) Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz DR DR This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 2 USA: Europe: Asia:

13 DR83DC9Y Industrial / Chemical Processing Blowers DR HP Regenerative Blower (2 PLACES) OUT MM NOTES 1 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN..397 DIA. 1.1 (2 MTG. HOLES) Part/ Model Number DR83DC9Y Specification Units Motor Enclosure - Shaft Mtl. - TEFC -CS Horsepower - 1/8 Voltage AC 115/23 Phase - Frequency - Single - 6 Hz Insulation Class - B NEMA Rated Motor Amps Amps (A) 1.8/1.-.9 Service Factor - 1. Max. Blower Amps Amps (A) 1.18/.59 Locked Rotor Amps Amps (A) 8.7/4.35 NEMA Starter Size - / Shipping Weight Lbs 18 Kg 8.2 Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperaturs - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 3 USA: Europe: Asia:

14 Industrial / Chemical Processing Blowers DR HP Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 24 IWG Maximum vacuum: 23.2 IWG Standard motor: 1/8 HP, TEFC UL & CSA approved motor with permanently sealed ball bearings Inlet & outlet internal muffling Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Cast iron (threaded) or face flanges for application-specific needs ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves External mufflers for additional silencing Air knives (used on blow-off applications) Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz DR DR This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 4 USA: Europe: Asia:

15 Industrial / Chemical Processing Blowers DR 11 & CP HP Regenerative Blower ROTATION DIRECTION MM MTG HOLES /2 FEMALE THREAD BOTH PORTS NOTES 1 TERMAL BOX CONNECTOR HOLE.88 (22) DIA. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. Part/ Model Number DR11Y9M DR11Y72M DR11Y86M CP11FB91MLR Specification Units Motor Enclosure - Shaft Mtl. - TEFC - CS TEFC - CS TEFC - CS CHEM TEFC - SS Horsepower Voltage AC 115/23 23/ /46 Phase - Frequency - Single - 6 Hz Three - 6 Hz Three - 6 Hz Three - 6 Hz Insulation Class - F F F F NEMA Rated Motor Amps Amps (A) 3.4/ /1.2/ /.6 Service Factor Max. Blower Amps Amps (A) 3.4/ / /.65 Locked Rotor Amps Amps (A) 16.4/ / /2.9 NEMA Starter Size - / -/ -/ Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperaturs - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 5 USA: Europe: Asia:

16 Industrial / Chemical Processing Blowers DR 11 & CP HP Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum flow: 31 SCFM Maximum pressure: 32 IWG Maximum vacuum: 28.5 IWG Standard motor:.33 HP, TEFC UL & CSA approved motor with permanently sealed ball bearings Inlet & outlet internal muffling Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves External mufflers for additional silencing Air knives (used on blow-off applications) Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz DR DR This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 6 USA: Europe: Asia:

17 Industrial / Chemical Processing Blowers DR 22 & CP HP Regenerative Blower STANDARD ROTATION MM DIA. 1 (4X) /4-11 1/2 NPSC STRAIGHT THREAD (2X) CAST IRON FLANGES NOTES 1 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. Part/ Model Number DR22Y9M DR22Y72M DR22Y86M CP22AE72MLR CP22FA91MLR Specification Units Motor Enclosure - Shaft Mtl. - TEFC - CS TEFC - CS TEFC - CS CHEM TEFC - CS CHEM TEFC - SS Horsepower Voltage AC 115/23 23/ /46 23/46 Phase - Frequency - Single - 6 Hz Three - 6 Hz Three - 6 Hz Three - 6 Hz Three - 6 Hz Insulation Class - F F F F F NEMA Rated Motor Amps Amps (A) 3.4/ / /.6 1.2/.6 Service Factor Max. Blower Amps Amps (A) 5.2/ / / /.77 Locked Rotor Amps Amps (A) 16.4/ / / /3.2 NEMA Starter Size - / / / / Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperaturs - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 7 USA: Europe: Asia:

18 Industrial / Chemical Processing Blowers DR 22 & CP HP Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 4 IWG Maximum vacuum: 35 IWG Standard motor:.33 HP, TEFC UL & CSA approved motor with permanently sealed ball bearings Inlet & outlet internal muffling Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models Cast iron (threaded) or face flanges for application-specific needs ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves External mufflers for additional silencing Air knives (used on blow-off applications) Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz DR DR This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 8 USA: Europe: Asia:

19 Industrial / Chemical Processing Blowers DR 33 & CP 33.5 HP Regenerative Blower L ROTATION DIRECTION DIA. 1.1 (4) MTG. HOLES MM 287 NOTES 1 TERMAL BOX CONNECTOR HOLE.88 (22.4) DIA. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. 1 1/4-11 1/2 NPSC FEMALE THREAD BOTH PORTS MODEL DR33AE9M DR33AE72M DR33AE86M L (/MM) 11.86/ / /33 Part/ Model Number DR33AE9M DR33AE72M DR33AE86M CP33FA91MLR Specification Units Motor Enclosure - Shaft Mtl. - TEFC - CS TEFC - CS TEFC - CS CHEM TEFC - SS Horsepower Voltage AC 115/23 23/ /46 Phase - Frequency - Single - 6 Hz Three - 6 Hz Three - 6 Hz Three - 6 Hz Insulation Class - F F F F NEMA Rated Motor Amps Amps (A) 6.2/ / /.6 Service Factor Max. Blower Amps Amps (A) 6/3 1.63/ /.83 Locked Rotor Amps Amps (A) 21/ / /4.6 NEMA Starter Size - / / / Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperaturs - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 9 USA: Europe: Asia:

20 Industrial / Chemical Processing Blowers DR 33 & CP 33.5 HP Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 48 IWG Maximum vacuum: 45 IWG Standard motor:.5 HP, TEFC (threaded) UL & CSA approved motor with permanently sealed ball bearings Inlet & outlet internal muffling Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves External mufflers for additional silencing Air knives (used on blow-off applications) Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz DR DR This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 1 USA: Europe: Asia:

21 Industrial / Chemical Processing Blowers DR 353 & CP 353. HP Regenerative Blower L ROTATION DIRECTION OUT Ø MM DIA. 12 (4) MTG HOLES NOTES 1 TERMAL BOX CONNECTOR HOLE.88 (22) DIA. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. 1 1/2-11 1/2 NPSC THREAD BOTH PORTS MODEL DR353BR9M DR353BR72M L (/MM) 13.97/ /317 Part/ Model Number DR353BR9M DR353BR72M DR353BR86M CP353BR72MLR CP353FD72MLR Specification Units Motor Enclosure - Shaft Mtl. - TEFC - CS TEFC - CS TEFC - CS CHEM TEFC - CS CHEM TEFC - SS Horsepower Voltage AC 115/23 23/ /46 23/46 Phase - Frequency - Single - 6 Hz Three - 6 Hz Three - 6 Hz Three 6 Hz Three 6 Hz Insulation Class - F F F F F NEMA Rated Motor Amps Amps (A) 1./5. 3./ /1.5 3./1.5 Service Factor Max. Blower Amps Amps (A) 12/6 3.5/ /1. 3.5/1. Locked Rotor Amps Amps (A) 59.6/ / / /7.6 NEMA Starter Size - / / / / Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperaturs - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 11 USA: Europe: Asia:

22 Industrial / Chemical Processing Blowers DR 353 & CP 353. HP Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 5 IWG Maximum vacuum: 45 IWG Standard motor: 3/4 HP, TEFC (threaded) UL & CSA approved motor with permanently sealed ball bearings Inlet & outlet internal muffling Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves External mufflers for additional silencing Air knives (used on blow-off applications) Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz DR DR This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 12 USA: Europe: Asia:

23 Industrial / Chemical Processing Blowers DR 44 & CP HP Regenerative Blower L MM NOTES 1 TERMAL BOX CONNECTOR HOLE.88 (22.4) DIA. KNOCK-OUT 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN..47 DIA (4) MTG. HOLES 1 1/2-11 1/2 NPSC FEMALE THREAD BOTH PORTS MODEL DR44AL58M DR44AL72M DR44AL86M L (/MM) 14.41/ / /339.9 Part/ Model Number DR44AL58M DR44AL72M DR44AL86M CP44CU72MLR Specification Units Motor Enclosure - Shaft Mtl. - TEFC - CS TEFC - CS TEFC - CS CHEM TEFC - SS Horsepower Voltage AC 115/23 23/ /46 Phase - Frequency - Single - 6 Hz Three - 6 Hz Three - 6 Hz Three - 6 Hz Insulation Class - F F F F NEMA Rated Motor Amps Amps (A) 11.4/5.7 3./ /1.5 Service Factor Max. Blower Amps Amps (A) 14.5/ / /2. Locked Rotor Amps Amps (A) 7/35 21./ /1.5 NEMA Starter Size - / / / Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperaturs - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 13 USA: Europe: Asia:

24 Industrial / Chemical Processing Blowers DR 44 & CP HP Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 58 IWG Maximum vacuum: 5 IWG Standard motor: 1. HP, TEFC (threaded) UL & CSA approved motor with permanently sealed ball bearings Inlet & outlet internal muffling Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves External mufflers for additional silencing Air knives (used on blow-off applications) Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz DR DR This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 14 USA: Europe: Asia:

25 Industrial / Chemical Processing Blowers DR 454 & CP HP Regenerative Blower L ROTATION DIRECTION OUT MM NOTES 1 TERMAL BOX CONNECTOR HOLE.88 (22) DIA. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN..59 DIA. 15 (6) MTG HOLES 1 1/2-11 1/2 NPSC FEMALE THREAD BOTH PORTS MODEL DR454R58M DR454R72M L (/MM) 14.47/ /338 Part/ Model Number DR454R58M DR454R72M DR454R86M CP454EZ72MLR Specification Units Motor Enclosure - Shaft Mtl. - TEFC - CS TEFC - CS TEFC - CS CHEM TEFC -SS Horsepower Voltage AC 115/23 23/ /46 Phase - Frequency - Single - 5/6 Hz Three - 5/6 Hz Three - 5/6 Hz Three - 5/6 Hz Insulation Class - F F F F NEMA Rated Motor Amps Amps (A) 15.6/ / /2.3 Service Factor Max. Blower Amps Amps (A) 18/9 5.2/ /2.6 Locked Rotor Amps Amps (A) 84/42 32/ /16 NEMA Starter Size - 1/ / / Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperaturs - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 15 USA: Europe: Asia:

26 Industrial / Chemical Processing Blowers DR 454 & CP HP Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 65 IWG Maximum vacuum: 6 IWG Standard motor: 1.5 HP, TEFC (threaded) UL & CSA approved motor with permanently sealed ball bearings Inlet & outlet internal muffling Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves External mufflers for additional silencing Air knives (used on blow-off applications) Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz DR DR This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 16 USA: Europe: Asia:

27 Industrial / Chemical Processing Blowers DR 55 & CP / 3. HP Regenerative Blower L DIA ROTATION DIRECTION 7.18 DIA C B OUT.37 REF. 9.4 MM DIA. 15 (4) MTG HOLES NOTES 1 TERMAL BOX CONNECTOR HOLE.88 (22) DIA. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. 1 1/2-11 1/2 NPSC FEMALE THREAD BOTH PORTS REF MODEL DR55AS58M DR55AS72M DR55AS86M DR55K58M DR55K72M L (/MM) 15.63/ / / / /397 B (/MM) 4.63/ / / / /111 C (/MM) 5.64/ / / / /131 Part/ Model Number DR55AS58M DR55AS72M DR55AS86M DR55K58M DR55K72M CP55FE72MLR CP55CT72MLR Specification Units Motor Enclosure - Shaft Mtl. - TEFC - CS TEFC - CS TEFC - CS TEFC - CS TEFC - CS CHEM TEFC - SS CHEM TEFC - SS Horsepower Voltage AC 115/23 23/ /23 23/46 23/46 23/46 Phase - Frequency - Single - 6 Hz Three - 6 Hz Three - 6 Hz Single - 6 Hz Three - 6 Hz Three - 6 Hz Three - 6 Hz Insulation Class - F F F F F F F NEMA Rated Motor Amps Amps (A) 18.2/ / / / / /2.7 Service Factor Max. Blower Amps Amps (A) 24/11.5 7/ /14 8.8/ / /3.4 Locked Rotor Amps Amps (A) 138/69 38/ /97 88/44 88/44 38/19 NEMA Starter Size - 1/ / 1.5/ / / / Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperaturs - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 17 USA: Europe: Asia:

28 Industrial / Chemical Processing Blowers DR 55 & CP / 3. HP Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 88 IWG Maximum vacuum: 73 IWG Standard motor: 2. HP, TEFC (threaded) UL & CSA approved motor with permanently sealed ball bearings Inlet & outlet internal muffling Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves External mufflers for additional silencing Air knives (used on blow-off applications) Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz DR55K72M 6 DR55AS72M DR55K58M 45 DR55AS58M DR55K72M 6 DR55AS72M 149 DR55K58M DR55AS58M This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 18 USA: Europe: Asia:

29 Industrial / Chemical Processing Blowers DR 513 & CP HP Regenerative Blower ROTATION OUT MM NOTES 1 TERMAL BOX CONNECTOR HOLE.88 (22) DIA. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN DIA (4) MTG HOLES /2-11 1/2 NPSC 12.8 FEMALE THREAD 325 BOTH PORTS Part/ Model Number DR513R72 DR513R58 DR513R86 CP513EZ72LR Specification Units Motor Enclosure - Shaft Mtl. - TEFC - CS TEFC - CS TEFC - CS CHEM TEFC -SS Horsepower Voltage AC 23/46 115/ /46 Phase - Frequency - Three - 6 Hz Single - 6 Hz Three - 6 Hz Three - 6 Hz Insulation Class - F F F F NEMA Rated Motor Amps Amps (A) 4.6/ / /2.3 Service Factor Max. Blower Amps Amps (A) 5/2.5 19/ /2.5 Locked Rotor Amps Amps (A) 43/21 12/ /21 NEMA Starter Size - / 1/ / Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperaturs - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 19 USA: Europe: Asia:

30 Industrial / Chemical Processing Blowers DR 513 & CP HP Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 88 IWG Maximum vacuum: 8 IWG Standard motor: 1.5 HP, TEFC (threaded) UL & CSA approved motor with permanently sealed ball bearings Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz DR DR This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 2 USA: Europe: Asia:

31 Industrial / Chemical Processing Blowers DR 523 & CP HP High Pressure Regenerative Blower L SEE NOTE ROTATION DIRECTION OUT MM DIA. 15. (4) MTG. HOLES 1 1/2-11 1/2 NPSC FEMALE THREAD BOTH PORTS NOTES 1 TERMAL BOX CONNECTOR HOLE.88 (22.4) DIA. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. MODEL DR523K72 DR523K58 L (/MM) 15.91/ /49.5 Part/ Model Number DR523K72 DR523K58 DR523K86 CP523CS72LR Specification Units Motor Enclosure - Shaft Mtl. - TEFC-CS TEFC-CS TEFC-CS TEFC-SS Horsepower Voltage AC 23/46 115/ /46 Phase - Frequency - Three-6 hz Single-6 hz Three-6 hz Three-6 hz Insulation Class - F F F F NEMA Rated Motor Amps Amps (A) 8.8-8,6/4.3 27/ /4.3 Service Factor Max. Blower Amps Amps (A) 8.9/4.45 3/ /4.45 Locked Rotor Amps Amps (A) 91.3/ / /45.7 NEMA Starter Size - / 1.5/1 / Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 21 USA: Europe: Asia:

32 Industrial / Chemical Processing Blowers DR 523 & CP HP High Pressure Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 158 IWG Maximum vacuum: 135 IWG Standard motor: 3. HP, TEFC (threaded) UL & CSA approved motor with permanently sealed ball bearings Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz DR DR This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 22 USA: Europe: Asia:

33 15.6 Industrial / Chemical Processing Blowers DR 555 & CP / 4. HP Regenerative Blower L NOTES 1 TERMAL BOX CONNECTOR HOLE.88 (22) DIA. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. MODEL DR555CK72 DR555K72 DR555K58 L (/MM) 17.44/ / /441 Part/ Model Number DR555CK72 DR555CK86 DR555K72 DR555K58 DR555K86 CP555CS72MLR Specification Units Motor Enclosure - Shaft Mtl. - TEFC - CS TEFC - CS TEFC - CS TEFC - CS TEFC - CS CHEM TEFC - SS Horsepower Voltage AC 23/ /46 115/ /46 Phase - Frequency - Three - 6 Hz Three - 6 Hz Three - 6 Hz Single - 6 Hz Three - 6 Hz Three - 6 Hz Insulation Class - F F F F F F NEMA Rated Motor Amps Amps (A) 1/ / / /3.8 Service Factor Max. Blower Amps Amps (A) 13/ /4.4 28/ /4.4 Locked Rotor Amps Amps (A) 94/ /44 194/ /44 NEMA Starter Size - 1/ / 1.5/1 / Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperaturs - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 23 USA: Europe: Asia:

34 Industrial / Chemical Processing Blowers DR 555 & CP / 4. HP Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 115 IWG Maximum vacuum: 92 IWG Standard motor: 4. HP, TEFC (threaded) UL & CSA approved motor with permanently sealed ball bearings Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz DR555CK72 DR555K72 DR555K DR555CK72 DR555K72 DR555K This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 24 USA: Europe: Asia:

35 Industrial / Chemical Processing Blowers DR 6 & CP 6 3. / 5. HP Regenerative Blower L MUFFLER /2 NPSC FEMALE THREAD BOTH PORTS ROTATION DIRECTION OUT MM NOTES 1 TERMAL BOX CONNECTOR HOLE 1.6 (26.9) DIA. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN..562 DIA. (4) MTG. HOLES MODEL DR6D89 DR6K72 L (/MM) 18./ /457.2 Part/ Model Number DR6D89 DR6D5 DR6D86 DR6K72 CP6FF72LR HiE6D89 Specification Units Motor Enclosure - Shaft Mtl. - TEFC-CS TEFC-CS TEFC-CS TEFC-CS CHEM TEFC-SS TEFC-CS Horsepower Voltage AC 23/ /46 23/46 23/46 Phase - Frequency - Three - 6 Hz Single - 6 Hz Three - 6 Hz Three - 6 Hz Three - 6 Hz Three - 6 Hz Insulation Class - F F F F F F NEMA Rated Motor Amps Amps (A) 11.2/ / / /7.8 Service Factor Max. Blower Amps Amps (A) 16/ / / /7.4 Locked Rotor Amps Amps (A) / / / /76 NEMA Starter Size - 1/ / 1/1 1/1 Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperaturs - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 25 USA: Europe: Asia:

36 Industrial / Chemical Processing Blowers DR 6 & CP 6 3. / 5. HP Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 11 IWG Maximum vacuum: 91.2 IWG Standard motor: 5. HP, TEFC (threaded) UL & CSA approved motor with permanently sealed ball bearings pc. MOTOR OPTIONS International voltage & frequency (Hz) designs BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz DR6D89 DR6K72 DR6D DR6D89 DR6K72 DR6D This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 26 USA: Europe: Asia:

37 Industrial / Chemical Processing Blowers DR 633 & CP / 7.5 HP High Pressure Regenerative Blower DIRECTION OF ROTATION OUT MM.98 (2X) NOTES 1 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN CLUDES LET FILTER 2" NPSC FEMALE THREAD BOTH PORTS Part/ Model Number DR633AY72M DR633AY86M DR633D89M CP633FG72LRM Specification Units Motor Enclosure - Shaft Mtl. - TEFC-CS TEFC-CS TEFC-CS CHEM TEFC-SS Horsepower Voltage AC 23/ /46 23/46 Phase - Frequency - Three - 6 Hz Three - 6 Hz Three - 6 Hz Three - 6 Hz Insulation Class - F F F F NEMA Rated Motor Amps Amps (A) 23-21/ / /1.5 Service Factor Max. Blower Amps Amps (A) / / /9 Locked Rotor Amps Amps (A) 17/ /76 17/85 NEMA Starter Size - 2/ / 2/1 Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 27 USA: Europe: Asia:

38 Industrial / Chemical Processing Blowers DR 633 & CP / 7.5 HP High Pressure Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 2 IWG Maximum vacuum: 19 IWG Standard motor: 7.5 HP, TEFC (threaded) UL & CSA approved motor with permanently sealed ball bearings Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz DR633AY72M DR633D89M DR633AY72M DR633D89M This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 28 USA: Europe: Asia:

39 Industrial / Chemical Processing Blowers DR 656 & CP / 3.5 HP Regenerative Blower L STD. DIRECTION OF ROTATION Ø MM (4X) MTG HOLES " NPSC STRAIGHT THDS BOTH PORTS NOTES 1 TERMAL BOX CONNECTOR HOLE.88 (22) DIA. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. MODEL DR656CK72X DR656K72X L (/MM) 17.5/ /46.4 Part/ Model Number DR656CK72X DR656CK86X DR656CK5X DR656K72X DR656K58X CP656CR72XLR Specification Units Motor Enclosure - Shaft Mtl. - TEFC - CS TEFC - CS TEFC-CS TEFC - CS TEFC - CS CHEM TEFC-SS Horsepower Voltage AC 23/ /46 115/23 23/46 Phase - Frequency - Three - 6 Hz Three - 6 Hz Single - 6 Hz Three - 6 Hz Single - 6 Hz Three - 6 Hz Insulation Class - F F F F F F NEMA Rated Motor Amps Amps (A) 1./ /3.7 29/ /5. Service Factor Max. Blower Amps Amps (A) 11.4/ / / /5.7 Locked Rotor Amps Amps (A) 94/ /27 172/86 94/47 NEMA Starter Size - 1/ 1 / 1.5/1. 1/ Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperaturs - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 29 USA: Europe: Asia:

40 Industrial / Chemical Processing Blowers DR 656 & CP / 3.5 HP Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 11 IWG Maximum vacuum: 89 IWG Standard motor: 4. HP, TEFC UL & CSA approved motor with permanently sealed ball bearings Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models Cast iron cover for additional noise resonance ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Blower Performance at Standard Conditions 6 Hz 5 Hz DR656K58X DR656K72X DR656CK72X DR656CK5X DR656K58X DR656K72X DR656CK72X DR656CK5X This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 3 USA: Europe: Asia:

41 Industrial / Chemical Processing Blowers DR 7 & CP 7 4. / 5. HP Regenerative Blower L ROTATION DIRECTION /2" NPSC FEMALE THREADS BOTH PORTS MM 2. 5 R NOTES 1 TERMAL BOX CONNECTOR HOLE 1.6 (26) DIA. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN C L OF BLOWER MODEL L (/MM) DR7CK72X 18.55/471 DR7CK86X 18.55/471 DR7D89X 18.55/471 DR7D86X 18.55/471 DR7D5MX 18.55/471 Part/ Model Number DR7CK72X DR7CK86X DR7D89X CP7FF72XLR CP7CR72XLR Specification Units Motor Enclosure - Shaft Mtl. - TEFC-CS TEFC-CS TEFC-CS CHEM TEFC-SS CHEM TEFC-SS Horsepower Voltage AC 23/ /46 23/46 23/46 Phase - Frequency - Three-6 hz Three-6 hz Three - 6 hz Three - 6 hz Three-6 hz Insulation Class - F F F F F NEMA Rated Motor Amps Amps (A) 1/ /6 12/6 1/5 Service Factor Max. Blower Amps Amps (A) 12/ / /7.6 12/6 Locked Rotor Amps Amps (A) 94/ /97 194/97 94/47 NEMA Starter Size - 1/ 1/ 1/ 1/ Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 31 USA: Europe: Asia:

42 Industrial / Chemical Processing Blowers DR 7 & CP 7 4. / 5. HP Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 83 IWG Maximum vacuum: IWG Standard motor: 4. HP, TEFC (threaded) UL & CSA approved motor with permanently sealed ball bearings Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz DR7D89X DR7CK72X DR7D89X DR7CK72X This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 32 USA: Europe: Asia:

43 Industrial / Chemical Processing Blowers DR S7 7.5 HP High Pressure Regenerative Blower /2 NPT FEMALE THREAD BOTH PORTS A /2 NPT FEMALE THREAD BOTH PORTS OUT NOTE 1 MM NOTES 1 TERMAL BOX CONNECTOR HOLE 1.6 (26.9) DIA. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. A DIA (4) MTG. HOLES SECTION VIEW A-A Part/ Model Number DRS7X72 DRS7X86 Specification Units Motor Enclosure - Shaft Mtl. - ODP-CS ODP-CS Horsepower Voltage AC 23/46 5 Phase - Frequency - Three-6 Hz Three-6 Hz Insulation Class - F F NEMA Rated Motor Amps Amps (A) 19.4/ Service Factor Max. Blower Amps Amps (A) 24/ Locked Rotor Amps Amps (A) 166/83 66 NEMA Starter Size - 1/1 1 Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 33 USA: Europe: Asia:

44 Industrial / Chemical Processing Blowers DR S7 7.5 HP High Pressure Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 14 IWG Maximum vacuum: 112 IWG Standard motor: 7.5 HP, ODP (threaded) UL & CSA approved motor with permanently sealed ball bearings MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz DRS DRS This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 34 USA: Europe: Asia:

45 Industrial / Chemical Processing Blowers DR 88 & CP / 7.5 HP Regenerative Blower L OUT C DIA (8) MTG. HOLES MM NOTES 1 TERMAL BOX CONNECTOR HOLE 1.6 (26.9) DIA. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. 2 1/2-8 NPSC FEMALE THREAD BOTH PORTS MODEL DR88AY72MX DR88D89MX L (/MM) 22.23/ /49.5 Part/ Model Number DR88AY72MX DR88AY86MX DR88D89MX CP88FG72MXLR HiE88AY72MX Specification Units Motor Enclosure - Shaft Mtl. - TEFC-CS TEFC-CS TEFC-CS CHEM TEFC-SS TEFC-CS Horsepower Voltage AC 23/ /46 23/46 23/46 Phase - Frequency - Three-6 hz Three-6 hz Three-6 hz Three-6 hz Three-6 hz Insulation Class - F F F F F NEMA Rated Motor Amps Amps (A) 17.8/ / / /8.9 Service Factor Max. Blower Amps Amps (A) 28/ /7 28/14 28/14 Locked Rotor Amps Amps (A) 12/ /76 12/6 12/6 NEMA Starter Size - 1/1 1 1/ 1/1 1/1 Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 35 USA: Europe: Asia:

46 Industrial / Chemical Processing Blowers DR 88 & CP / 7.5 HP Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 12 IWG Maximum vacuum: 95 IWG Standard motor: 7.5 HP, TEFC (threaded) UL & CSA approved motor with permanently sealed ball bearings Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz DR88AY72MX DR88D89MX DR88AY72MX DR88D89MX This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 36 USA: Europe: Asia:

47 Industrial / Chemical Processing Blowers DR 833 & CP / 1. HP Regenerative Blower DIRECTION OF ROTATION ROTATION 1.5 DIA OUT (2X) " /2 NPSC FEMALE THREAD BOTH PORTS MM MTG. HOLE DETAIL (4X) NOTES 1 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. FILTER CLUDED Part/ Model Number DR833BB72M DR833BB86M DR833AY72M DR833AY86M CP833FH72MLR Specification Units Motor Enclosure - Shaft Mtl. - TEFC-CS TEFC-CS TEFC-CS TEFC-CS CHEM TEFC-SS Horsepower Voltage AC 23/ / /46 Phase - Frequency - Three - 6 Hz Three - 6 Hz Three - 6 Hz Three - 6 Hz Three - 6 Hz Insulation Class - F F F F F NEMA Rated Motor Amps Amps (A) 31-28/ / /14 Service Factor Max Blower Amps Amps (A) 26-24/ / /12 Locked Rotor Amps Amps (A) 19/ / /95 NEMA Starter Size - 2/1 1 2/1 1 2/1 Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 37 USA: Europe: Asia:

48 Industrial / Chemical Processing Blowers DR 833 & CP / 1. HP Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 258 IWG Maximum vacuum: 174 IWG Standard motor: 1 HP, TEFC (threaded) UL & CSA approved motor with permanently sealed ball bearings Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz DR833BB72M DR833AY72M DR833BB72M DR833AY72M This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 38 USA: Europe: Asia:

49 Industrial / Chemical Processing Blowers DR 858 & CP / 1. HP Regenerative Blower L /2-8 NPSC FEMALE THREAD BOTH PORTS OUT ROTATION DIRECTION NOTE 1 MM NOTES 1 TERMAL BOX CONNECTOR HOLE 1.6 (26.9) DIA. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.. X 2. SLOT 19.5 X 5.8 (4) PLACES MODEL DR858AY72W DR858BB72W L (/MM) 23.6/ /589 Part/ Model Number DR858BB72W DR858BB86W DR858AY72W CP858FH72WLR HiE858BB72W Specification Units Motor Enclosure - Shaft Mtl. - TEFC-CS TEFC-CS TEFC-CS CHEM TEFC-SS TEFC-CS Horsepower Voltage AC 23/ /46 23/46 23/46 Phase - Frequency - Three-6 hz Three-6 hz Three-6 hz Three-6 hz Three-6 hz Insulation Class - F F F F F NEMA Rated Motor Amps Amps (A) 26/ /8.9 26/13 26/13 Service Factor Max. Blower Amps Amps (A) 28/ /14 28/14 28/14 Locked Rotor Amps Amps (A) 162/ /6 162/81 162/81 NEMA Starter Size - 2/1 1 1/1 2/1 2/1 Shipping Weight Lbs Kg Model (Base Mount) - DR858BB72X DR858BB86X DR858AY72X Part Number (Base Mount) Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 39 USA: Europe: Asia:

50 Industrial / Chemical Processing Blowers DR 858 & CP / 1. HP Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 125 IWG Maximum vacuum: 14.8 IWG Standard motor: 1 HP, TEFC (threaded) UL & CSA approved motor with permanently sealed ball bearings Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz DR858AY72W DR858BB72W DR858AY72W DR858BB72W This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 4 USA: Europe: Asia:

51 Industrial / Chemical Processing Blowers DR P9 15. / 2. HP Regenerative Blower DIA. SLIP-ON 11.6 A L ROTATION DIRECTION 18. DIA REF MM 2 1/2-8 NPSC FEMALE THREAD BOTH PORTS A DIA (4) PLACES SECTION VIEW A-A NOTES 1 TERMAL BOX CONNECTOR HOLE 1.37 (34.8) DIA. 2 PRESSURE OUTLET CONNECTION. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. MODEL DRP9BM72C DRP9BL72C L (/MM) 31./ /849.4 Part/ Model Number DRP9BM72C DRP9BM72D DRP9BM86C DRP9BM86D DRP9BL72C DRP9BL72D Specification Units Motor Enclosure - Shaft Mtl. - ODP-CS ODP - CS ODP-CS ODP - CS ODP-CS ODP - CS Horsepower Voltage AC 23/46 23/ /46 23/46 Phase - Frequency - Three-6 hz Three - 6 hz Three-6 hz Three - 6 hz Three-6 hz Three - 6 hz Insulation Class - F F F F F F NEMA Rated Motor Amps Amps (A) 49/ / / /18.5 Service Factor Max. Blower Amps Amps (A) 6/3 6/ /25 5/25 Locked Rotor Amps Amps (A) 36/153 36/ / /128 NEMA Starter Size - 3/2 3/ /2 2/2 Shipping Weight Lbs Kg Description - Pressure Mode Suction Mode Pressure Mode Suction Mode Pressure Mode Suction Mode Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 41 USA: Europe: Asia:

52 Industrial / Chemical Processing Blowers DR P9 15. / 2. HP Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 116 IWG Maximum vacuum: 95 IWG Standard motor: 2 HP, ODP (threaded) UL & CSA approved motor with permanently sealed ball bearings part # MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz DRP9BM72C DRP9BL72C DRP9BM72C DRP9BL72C This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 42 USA: Europe: Asia:

53 Industrial / Chemical Processing Blowers DR S9 15. / 2. HP High Pressure Regenerative Blower A L 2 1/2-8 NPSC FEMALE THREAD BOTH PORTS ROTATION DIRECTION X X X NOTE 1 MM A NOTES 1 TERMAL BOX CONNECTOR HOLE 1.37 (34.8) DIA. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN..6 X 1.35 SLOT(4) (DRS9BM72).56 (14.2) DIA. (DRS9BL72) SECTION VIEW A-A MODEL DRS9BM72 DRS9BL72 L (/MM) 31./ /849.4 Part/ Model Number DRS9BM72 DRS9BM86 DRS9BL72 Specification Units Motor Enclosure - Shaft Mtl. - ODP-CS ODP-CS ODP-CS Horsepower Voltage AC 23/ /46 Phase - Frequency - Three-6 Hz Three-6 Hz Three-6 Hz Insulation Class - F F F NEMA Rated Motor Amps Amps (A) 48/ /18 Service Factor Max. Blower Amps Amps (A) 56/ /28 Locked Rotor Amps Amps (A) 288/ /111 NEMA Starter Size - 3/2 2 2/2 Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 43 USA: Europe: Asia:

54 Industrial / Chemical Processing Blowers DR S9 15. / 2. HP High Pressure Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 26 IWG Maximum vacuum: 157 IWG Standard motor: 6 HP, ODP (threaded) UL & CSA approved motor with permanently sealed ball bearings part # MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz DRS9BL72C DRS9BM72C DRS9BL72C DRS9BM72C This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 44 USA: Europe: Asia:

55 Industrial / Chemical Processing Blowers DR 99 & CP / 15. HP Regenerative Blower MM NOTES 1 TERMAL BOX CONNECTOR HOLE 1.25 (31.8) DIA. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. Part/ Model Number DR99BE72W DR99BE86W DR99BB72W DR99BB86W CP99FJ72WLR HiE99BE72W Specification Units Motor Enclosure - Shaft Mtl. - TEFC-CS TEFC-CS TEFC-CS TEFC-CS CHEM TEFC-SS TEFC-CS Horsepower Voltage AC 28-23/ / / /46 Phase - Frequency - Three-6 hz Three-6 hz Three - 6 Hz Three-6 hz Three-6 hz Three-6 hz Insulation Class - F F F F F F NEMA Rated Motor Amps Amps (A) / / / /18.8 Service Factor Max. Blower Amps Amps (A) 42/ / /21 42/21 Locked Rotor Amps Amps (A) 318/ / / /159 NEMA Starter Size - 2/2 2 2/1 1 2/2 2/2 Shipping Weight Lbs Kg Model (Base Mount) Part Number (Base Mount) - - DR99BE72X DR99BE86X DR99BB72X DR99BB86X 8183 Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 45 USA: Europe: Asia:

56 Industrial / Chemical Processing Blowers DR 99 & CP / 15. HP Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 137 IWG Maximum vacuum: 16 IWG Standard motor: 15 HP, TEFC (threaded) UL & CSA approved motor with permanently sealed ball bearings Quiet operation within OSHA standards when properly piped and MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz DR99BE72W DR99BB72W DR99BE72W DR99BB72W This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 46 USA: Europe: Asia:

57 Industrial / Chemical Processing Blowers DR 979 & CP / 2. HP Regenerative Blower OUT ROTATION DIRECTION 4" NPSC PORTS B MM L E C D NOTES 1 TERMAL BOX CONNECTOR HOLE 1.9 DIA. (DR979BE72W) 1.3 DIA. (DR979BH72W). 2. (19.1) X 2. (5.8) 4X MOUNTG SLOTS. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. MODEL DR979BH72W DR979BE72W DR979BE86W L (/MM) 29./ / /655.6 B (/MM) C (/MM) 12.25/ / / / / /212.9 D (/MM) 13.19/ / /25.9 E (/MM) 8.9/ / /174.8 Part/ Model Number DR979BH72W DR979BE72W DR979BE86W DR979BH86W CP979FJ72WLR HiE979BE72W Specification Units Motor Enclosure - Shaft Mtl. - TEFC-CS TEFC-CS TEFC-CS TEFC-CS CHEM TEFC-SS TEFC-CS Horsepower Voltage AC 23/46 23/ /46 23/46 Phase - Frequency - Three-6 hz Three-6 hz Three-6 hz Three-6 hz Three-6 hz Three-6 hz Insulation Class - H H H H H H NEMA Rated Motor Amps Amps (A) 46/23 44/ /23 44/22 44/22 Service Factor Max. Blower Amps Amps (A) 6/3 52/ /33 52/26 52/26 Locked Rotor Amps Amps (A) 294/147 29/ /147 29/145 29/145 NEMA Starter Size - 3/2 2/2 2 3/2 2/2 2/2 Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 47 USA: Europe: Asia:

58 Industrial / Chemical Processing Blowers DR 979 & CP / 2. HP Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant CE compliant - Declaration of Conformity on file Maximum flow: 11 SCFM Maximum pressure: 8 IWG Maximum vacuum: 87 IWG Standard motor: 15 HP, TEFC Cast aluminum blower housing, impeller & cover; cast iron flanges (threaded) UL & CSA approved motor with permanently sealed ball bearings Inlet & outlet internal muffling Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) Chemical duty, high efficiency, inverter duty or industry-specific designs Vairous horsepowers for application-specific needs BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models Slip-on or face flanges for application-specific needs ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Switches - air flow, pressure, vacuum, or temperature External mufflers for additional silencing Air knives (used on blow-off applications) Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz DR979BE72W DR979BH72W DR979BE72W DR979BH72W This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 48 USA: Europe: Asia:

59 Industrial / Chemical Processing Blowers DR 1233 & CP HP High Pressure Regenerative Blower MM NOTES 1 TERMAL BOX CONNECTOR HOLE 1.38 (35) DIA. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. Part/ Model Number DR1233BH72W DR1233BH86W CP1233GD72LRW Specification Units Motor Enclosure - Shaft Mtl. - TEFC-CS TEFC-CS CHEM TEFC-SS Horsepower Voltage AC 28-23/ /46 Phase - Frequency - Three-6 Hz Three-6 Hz Three-6 Hz Insulation Class - F F F NEMA Rated Motor Amps Amps (A) 51-46/ /23 Service Factor Max. Blower Amps Amps (A) 5-46/ /23 Locked Rotor Amps Amps (A) 397/ /199 NEMA Starter Size - 3/2 2 3/2 Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 49 USA: Europe: Asia:

60 Industrial / Chemical Processing Blowers DR 1233 & CP HP High Pressure Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 255 IWG Maximum vacuum: 1 IWG Standard motor: 2 HP, TEFC (threaded) UL & CSA approved motor with permanently sealed ball bearings Inlet Filter part# Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz DR DR This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 5 USA: Europe: Asia:

61 Industrial / Chemical Processing Blowers DR P13 2. / 3. HP Regenerative Blower ROTATION DIRECTION NPSC FEMALE 1.53/38.86 DEEP FLEX TUBG (2X) H C E X 2. SLOT 19.1 X 5.8 (4X) G NPT (2X) FEMALE THREAD MM NOTES DRP13BP72C MODEL SHOWN. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. PART NUMBER MODEL C /MM H /MM G /MM E /MM DRP13BP72C DRP13BP72D DRP13BP86C DRP13BP86D DRP13BM72C DRP13BM72D 11.3/ / / / / / / / / / / / / / / / / / / / / / / /35.5 Part/ Model Number DRP13BP72C DRP13BP72D DRP13BP86C DRP13BP86D DRP13BM72C DRP13BM72D Specification Units Motor Enclosure - Shaft Mtl. - ODP-CS ODP-CS ODP-CS ODP-CS ODP-CS ODP-CS Horsepower Voltage AC 23/46 23/ /46 23/46 Phase - Frequency - Three-6 hz Three-6 hz Three-6 hz Three-6 hz Three-6 hz Three-6 hz Insulation Class - F F F F F F NEMA Rated Motor Amps Amps (A) 7/35 7/ / /24.5 Service Factor Locked Rotor Amps Amps (A) 38/19 38/ /153 36/153 Max. Blower Amps Amps (A) 11/55 11/ /32 64/32 NEMA Starter Size - 3/3 3/ /2 3/2 Shipping Weight Lbs Kg Description - Pressure Mode Suction Mode Pressure Mode Suction Mode Pressure Mode Suction Mode Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 51 USA: Europe: Asia:

62 Industrial / Chemical Processing Blowers DR P13 2. / 3. HP Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 115 IWG Maximum vacuum: 13 IWG Standard motor: 3 HP, ODP (threaded) UL & CSA approved motor with permanently sealed ball bearings (part# ) MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz DRP13BP72C DRP13BM72C DRP13BP72C DRP13BM72C This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 52 USA: Europe: Asia:

63 Industrial / Chemical Processing Blowers DR S13 2. / 3. HP High Pressure Regenerative Blower NOTES 1 TERMAL BOX CONNECTOR HOLE 2.5 (63.5) DIA NPSC FEMALE THREAD, BOTH PORTS 3 LABEL DICATES ROTATION DIRECTION AND & OUT PORT LOCATIONS. 5 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 6 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN OUT MM BOTH PORTS SECTION VIEW A-A SLOTS.x2. (19x5.8) (4) PLACES Part/ Model Number DRS13BP72 DRS13BP86 DRS13BM72 Specification Units Motor Enclosure - Shaft Mtl. - ODP-CS ODP-CS ODP-CS Horsepower Voltage AC 23/ /46 Phase - Frequency - Three-6 Hz Three-6 Hz Three-6 Hz Insulation Class - F F F NEMA Rated Motor Amps Amps (A) 78/ /24.5 Service Factor Max. Blower Amps Amps (A) 8/4 32 7/153 Locked Rotor Amps Amps (A) 38/ /153 NEMA Starter Size - 3/3 3 3/2 Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 53 USA: Europe: Asia:

64 Industrial / Chemical Processing Blowers DR S13 2. / 3. HP High Pressure Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 195 IWG Maximum vacuum: 132 IWG Standard motor: 3 HP, ODP (threaded) UL & CSA approved motor with permanently sealed ball bearings (part# ) MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz DRS DRS This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 54 USA: Europe: Asia:

65 Industrial / Chemical Processing Blowers DR 14 & CP / 25. / 3.HP Regenerative Blower SEE NOTE 1 SEE NOTE 1 OUT "-8 NPSC FEMALE THREAD BOTH PORTS (CAST IRON) ROTATION DIRECTION D DIA DIA MM SLOTS. x 2. (19.1 x 5.8) 4X PLACES NOTES L 1 LIFTG SLOT: 1. X 1.7 (25.4 X 43.2) 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. MODEL DR14DW72MW L (/MM) 31.55/81.4 D (/MM) 1.98/5.3 Part/ Model Number DR14DW72MW DR14DW86MW DR14DT72MW DR14BH72MW CP14FK72MWLR HiE14DW72MW Specification Units Motor Enclosure - Shaft Mtl. - TEFC-CS TEFC-CS TEFC-CS TEFC-CS CHEM TEFC-SS TEFC-CS Horsepower Voltage AC 23/ /46 23/46 23/46 23/46 Phase - Frequency - Three-6 hz Three-6 hz Three-6 hz Three-6 hz Three-6 hz Three-6 hz Insulation Class - F F F F F F NEMA Rated Motor Amps Amps (A) 66/ /29 46/23 66/33 66/33 Service Factor Max. Blower Amps Amps (A) 9/ /45 6/3 9/45 9/45 Locked Rotor Amps Amps (A) 43/ / /147 43/215 43/215 NEMA Starter Size - 3/3 3 3/3 3/2 3/3 3/3 Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 55 USA: Europe: Asia:

66 Industrial / Chemical Processing Blowers DR 14 & CP / 25. / 3.HP Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 15 IWG Maximum vacuum: 12 IWG Standard motor: 3 HP, TEFC (threaded) UL & CSA approved motor with permanently sealed ball bearings Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz DR14DW72MW DR14DT72MW DR14BH72MW DR14DW72MW DR14DT72MW DR14BH72MW This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 56 USA: Europe: Asia:

67 Industrial / Chemical Processing Blowers DR P15 4. / 6. HP Regenerative Blower A 2.81 DIA (2 PLACES) REF DIA OUT REF OUT MM NOTES 1 TERMAL BOX CONNECTOR HOLE 2.5 (63.5) DIA NPSC FEMALE THREAD, BOTH PORTS 3 PRESSURE CONNECTION 6-8 NPSC FEMALE THREAD. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN A X 2. SLOT (4) PLACES SECTION VIEW A-A Part/ Model Number DRP15EE72C DRP15EE72D DRP15BQ72C DRP15BQ72D DRP15BQ86C DRP15BQ86D Specification Units TBD TBD Motor Enclosure - Shaft Mtl. - ODP-CS ODP - CS ODP - CS ODP - CS ODP - CS ODP - CS Horsepower Voltage AC 23/46 23/46 23/46 23/ Phase - Frequency - Three-6 hz Three - 6 hz Three - 6 hz Three - 6 hz Three - 6 hz Three - 6 hz Insulation Class - F F F F F F NEMA Rated Motor Amps Amps (A) 14/7 14/7 96/48 96/ Service Factor Locked Rotor Amps Amps (A) 87/435 87/435 63/315 63/315 54/27 54/27 Max. Blower Amps Amps (A) 17/85 17/85 16/8 16/ NEMA Starter Size - 5/4 5/4 4/3 4/3 3 3 Shipping Weight Lbs Kg Description - Pressure Mode Suction Mode Pressure Mode Suction Mode Pressure Mode Suction Mode Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 57 USA: Europe: Asia:

68 Industrial / Chemical Processing Blowers DR P15 4. / 6. HP Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 15 IWG Maximum vacuum: 115 IWG Standard motor: 6 HP, ODP (threaded) UL & CSA approved motor with permanently sealed ball bearings (part# ) MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz DRP15EE72D DRP15BQ72C DRP15EE72D DRP15BQ72C This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 58 USA: Europe: Asia:

69 Industrial / Chemical Processing Blowers DR S15 4. HP High Pressure Regenerative Blower 5 OUT BOTH PORTS 2 OUT A MM NOTES 1 TERMAL BOX CONNECTOR HOLE.88 (22) DIA NPSC FEMALE THREAD, BOTH PORTS. 3 FOUR MOUNTG SLOTS. (19) X 2. (5.8). 4 TWO LIFTG SLOTS 1. (25.4) X 1.7 (43.2). 5 LABEL DICATES ROTATION DIRECTION AND & OUT PORT LOCATIONS. 6 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 7 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN A SECTION VIEW A-A Part/ Model Number DRS15BQ72 DRS15BQ86 Specification Units 8152 TBD Motor Enclosure - Shaft Mtl. - ODP-CS ODP-CS Horsepower Voltage AC 23/46 5 Phase - Frequency - Three-6 Hz Three-6 Hz Insulation Class - F F NEMA Rated Motor Amps Amps (A) 96/ Service Factor Max. Blower Amps Amps (A) 14/7 52 Locked Rotor Amps Amps (A) 63/ NEMA Starter Size - 4/3 3 Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 59 USA: Europe: Asia:

70 Industrial / Chemical Processing Blowers DR S15 4. HP High Pressure Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum flow: 925 SCFM Maximum pressure: 2 IWG Maximum vacuum: IWG Standard motor: 4 HP, ODP (threaded) UL & CSA approved motor with permanently sealed ball bearings Quiet operation within OSHA standards when properly piped or muffled - 1 inlet muffler included (part# ) MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves External mufflers for additional silencing Air knives (used on blow-off applications) Variable frequency drive package Blower Performance at Standard Conditions 6 Hz DRS This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. C 6 USA: Europe: Asia:

71

72 Environmental / Chemical Processing Blowers Our environmental EN blowers are designed the same as the DR blowers, except added features include: Heavy duty cast aluminum manifold Our spark resistant housing, cover, impeller, muffler tower, and manifold are vacuum impregnated Teflon lip seal in a stainless steel case standard for leakage containment to 25 cc/min or less Explosion-proof motors standard and available in a variety of world voltages All metal-to-metal surfaces are sealed with RTV sealant Various UL explosion-proof listings. Consult factory. Environmental (EN) regenerative blowers are also available in our Chemical Processing (CP) configuration: Chem-Tough TM surface conversion corrsion resistant treatment for all castings Teflon lip seal in a stainless steel case standard for leakage containment to 25 cc/min or less Chemical duty motors with 33 stainless steel motor shafts Stainless steel hardware throughout Nickel plated flanges and muffler retainers USA: Europe: Asia:

73 Environmental / Chemical Processing Blowers EN 11 & CP 11.5 HP Sealed Regenerative w/explosion-proof Motor ROTATION DIRECTION OUT MM (9.6) DIA 2X MTG. HOLES NOTES 1 TERMAL BOX CONNECTOR HOLE. NPT 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN /2 NPSC FEMALE THREAD BOTH PORTS Part/Model Number EN11AG58L EN11AG91L CP11FN58LR CP11FN91LR Specification Units Motor Enclosure - Shaft Mtl. - Explosion-proof-CS Explosion-proof-CS CHEM XP-SS CHEM XP-SS Horsepower Phase - Frequency Voltage - Single-6 hz Three-6 hz Single-6 hz Three-6 hz Motor Nameplate Amps AC 115/23 23/46 115/23 23/46 Max. Blower Amps Amps (A) 7.4/3.7.9/ /3.7.9/.45 Locked Rotor Amps Amps (A) 6/3 1.5/. 6/3 1.5/. Service Factor Amps (A) 38/19 8.9/4.5 38/19 8.9/4.5 Starter Size - / / / / Thermal Protection XP Motor Class - Group - Not Required Not Required Not Required Not Required - I-D I-D I-D I-D Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. XP Motor Class - Group - See Explosive Atmosphere Classification Chart in Section I USA: Europe: Asia: D 1

74 Environmental / Chemical Processing Blowers EN 11 & CP 11.5 HP Sealed Regenerative w/explosion-proof Motor FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 25 IWG Maximum vacuum: 23 IWG Standard motor:.5 HP, explosion-proof Cast aluminum blower housing, impeller, cover & manifold; cast iron UL & CSA approved motor with permanently sealed ball bearings for explosive gas atmospheres Class I Group D minimum Sealed blower assembly Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves External mufflers for additional silencing Air knives (used on blow-off applications) Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz EN EN USA: Europe: Asia: D 2 com

75 Environmental / Chemical Processing Blowers EN 33 & CP 33.5 HP Sealed Regenerative w/explosion-proof motor OUT MM NOTES 1 TERMAL BOX CONNECTOR HOLE 3/4 NPT FEMALE THREAD> 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN..397 DIA. 1 (4) MTG HOLES 1 1/4" /2 NPSC FEMALE THREAD BOTH PORTS Part/Model Number EN33AG58L EN33AG91L CP33FN58LR CP33FN91LR Specification Units Motor Enclosure - Shaft Mtl. - Explosion-proof-CS Explosion-proof-CS CHEM XP-SS CHEM XP-SS Horsepower Phase - Frequency Voltage - Single-6 hz Three-6 hz Single-6 hz Three-6 hz Motor Nameplate Amps AC 115/23 23/46 115/23 23/46 Max. Blower Amps Amps (A) 9./ /. 9./ /. Locked Rotor Amps Amps (A) 7.2/ / / /.83 Service Factor Amps (A) 38/19 8.9/ /19 8.9/4.45 Starter Size - / / / / Thermal Protection XP Motor Class - Group - Not Required Not Required Not Required Not Required - I-D I-D I-D I-D Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. XP Motor Class - Group - See Explosive Atmosphere Classification Chart in Section I USA: Europe: Asia: D 3

76 Environmental / Chemical Processing Blowers EN 33 & CP 33.5 HP Sealed Regenerative w/explosion-proof motor FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 5 IWG Maximum vacuum: 45 IWG Standard motor:.5 HP, explosion-proof UL & CSA approved motor with permanently sealed ball bearings for explosive gas atmospheres Class I Group D minimum Sealed blower assembly Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz EN EN USA: Europe: Asia: D 4

77 Environmental / Chemical Processing Blowers EN 44 & CP HP Sealed Regenerative w/explosion-proof Motor L ROTATION DIRECTION DIA MM NOTES 1 TERMAL BOX CONNECTOR HOLE 3/4 NPT. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN..47 DIA (4) MTG. HOLES 1 1/2-11 1/2 NPSC FEMALE THREAD BOTH PORTS MODEL EN44AR58ML EN44AR72ML L (/MM) 16.41/ /393.7 Part/Model Number EN44AR58ML EN44AR72ML CP44FQ58MLR CP44FQ72MLR Specification Units Motor Enclosure - Shaft Mtl. - Explosion-proof-CS Explosion-proof-CS CHEM XP-SS CHEM XP-SS Horsepower Phase - Frequency Voltage - Single-6 hz Three-6 hz Single-6 hz Three-6 hz Motor Nameplate Amps AC 115/ /46 115/ /46 Max. Blower Amps Amps (A) 11.4/ / / /1.6 Locked Rotor Amps Amps (A) 14.4/ / / /1.8 Service Factor Amps (A) 72/36 2.2/1.1 72/36 2.2/1.1 Starter Size - / / / / Thermal Protection XP Motor Class - Group - Class B - Pilot Duty Class B - Pilot Duty Class B - Pilot Duty Class B - Pilot Duty - I-D, II-F&G I-D, II-F&G I-D, II-F&G I-D, II-F&G Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. XP Motor Class - Group - See Explosive Atmosphere Classification Chart in Section I USA: Europe: Asia: D 5

78 Environmental / Chemical Processing Blowers EN 44 & CP HP Sealed Regenerative w/explosion-proof Motor *ATEX model certified FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 52 IWG Maximum vacuum: 48 IWG Standard motor: 1. HP, explosion-proof Cast aluminum blower housing, impeller, cover & manifold; cast iron UL & CSA approved motor with permanently sealed ball bearings for explosive gas atmospheres Class I Group D minimum Sealed blower assembly Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz EN EN USA: Europe: Asia: D 6

79 Environmental / Chemical Processing Blowers EN 454 & CP HP Sealed Regenerative w/explosion-proof Motor ROTATION DIRECTION OUT MM NOTES 1 TERMAL BOX CONNECTOR HOLE 3/4 NPT. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN..59 DIA. 15 (6) MTG. HOLES 1 1 1/2-11 1/2 NPSC FEMALE THREAD BOTH PORTS REF Part/Model Number EN454W58ML EN454W72ML CP454W72MLR CP454FR72MLR Specification Units Motor Enclosure - Shaft Mtl. - Explosion-proof-CS Explosion-proof-CS CHEM XP-CS CHEM XP-SS Horsepower Phase - Frequency - Single-6 hz Three-6 hz Three-6 hz Three-6 hz Voltage AC 115/ /46 23/46 23/46 Motor Nameplate Amps Amps (A) 15/ / / /2.3 Max. Blower Amps Amps (A) 19/ / / /2.8 Locked Rotor Amps Amps (A) /16 32/16 32/16 Service Factor - 1/ / / / Starter Size Thermal Protection - Class B - Pilot Duty Class B - Pilot Duty Class B - Pilot Duty Class B - Pilot Duty XP Motor Class - Group - I-D, II-F&G I-D, II-F&G I-D, II-F&G I-D, II-F&G Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. XP Motor Class - Group - See Explosive Atmosphere Classification Chart in Section I USA: Europe: Asia: D 7

80 Environmental / Chemical Processing Blowers EN 454 & CP HP Sealed Regenerative w/explosion-proof Motor FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 65 IWG Maximum vacuum: 59 IWG Standard motor: 1.5 HP, explosion-proof Cast aluminum blower housing, impeller, cover & manifold; cast iron UL & CSA approved motor with permanently sealed ball bearings for explosive gas atmospheres Class I Group D minimum Sealed blower assembly Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz EN EN USA: Europe: Asia: D 8

81 Environmental / Chemical Processing Blowers EN 55 & CP / 2.5 HP Sealed Regenerative w/explosion-proof Motor MM NOTES 1 TERMAL BOX CONNECTOR HOLE 3/4 NPT. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. Part/Model Number EN55AX58ML EN55AX72ML CP55FS58MLR CP55FS72MLR Specification Units Motor Enclosure - Shaft Mtl. - Explosion-proof-CS Explosion-proof-CS CHEM XP-SS CHEM XP-SS Horsepower Phase - Frequency - Single-6 hz Three-6 hz Single-6 hz Three-6 hz Voltage AC 115/23 23/46 115/23 23/46 Motor Nameplate Amps Amps (A) 22/11 5.8/2.9 22/11 5.8/2.9 Max. Blower Amps Amps (A) 24/12 6.4/3.2 24/12 6.4/3.2 Locked Rotor Amps Amps (A) 112/56 56/28 112/56 56/28 Service Factor - 1/ / 1/ / Starter Size Thermal Protection - Class B - Pilot Duty Class B - Pilot Duty Class B - Pilot Duty Class B - Pilot Duty XP Motor Class - Group - I-D, II-F&G I-D, II-F&G I-D, II-F&G I-D, II-F&G Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. XP Motor Class - Group - See Explosive Atmosphere Classification Chart in Section I USA: Europe: Asia: D 9

82 Environmental / Chemical Processing Blowers EN 55 & CP / 2.5 HP Sealed Regenerative w/explosion-proof Motor FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: IWG Maximum vacuum: 7 IWG Standard motor: 2. HP, explosion-proof Cast aluminum blower housing, impeller, cover & manifold; cast iron UL & CSA approved motor with permanently sealed ball bearings for explosive gas atmospheres Class I Group D minimum Sealed blower assembly Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz EN55AX72ML EN55AX58ML EN55AX72ML EN55AX58ML USA: Europe: Asia: D 1

83 Environmental / Chemical Processing Blowers EN 513 & CP HP Sealed Regenerative w/explosion-proof Motor ROTATION DIRECTION OUT MM NOTES 1 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN..59 DIA. 15 (4) MTG. HOLES 1 1/2-11 1/2 NPSC FEMALE THREAD BOTH PORTS Part/Model Number EN513W58L EN513W72L CP513FR58LR CP513FR72LR Specification Units Motor Enclosure - Shaft Mtl. - Explosion-proof-CS Explosion-proof-CS CHEM XP-SS CHEM XP-SS Horsepower Phase - Frequency Voltage - Single-6 hz Three-6 hz Single-6 hz Three-6 hz Motor Nameplate Amps AC 115/ /46 115/ /46 Max. Blower Amps Amps (A) 15/ /2.3 15/ /2.3 Inrush Amps Amps (A) 19.4/ / / /2.7 Service Factor Amps (A) / /16 Starter Size - 1/ / 1/ / Thermal Protection XP Motor Class - Group - Class B - Pilot Duty Class B - Pilot Duty Class B - Pilot Duty Class B - Pilot Duty - I-D, II-F&G I-D, II-F&G I-D, II-F&G I-D, II-F&G Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. XP Motor Class - Group - See Explosive Atmosphere Classification Chart in Section I USA: Europe: Asia: D 11

84 Environmental / Chemical Processing Blowers EN 513 & CP HP Sealed Regenerative w/explosion-proof Motor FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 88 IWG Maximum vacuum: IWG Standard motor: 1.5 HP, explosion-proof Cast aluminum blower housing, impeller, cover & manifold; cast iron UL & CSA approved motor with permanently sealed ball bearings for explosive gas atmospheres Class I Group D minimum Sealed blower assembly Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz EN EN USA: Europe: Asia: D 12

85 Environmental / Chemical Processing Blowers EN 523 & CP HP High Pressure Sealed Regenerative w/explosion-proof Motor SEE NOTE 1 ROTATION DIRECTION OUT MM DIA. 15 (4) MTG. HOLES NOTES 1 TERMAL BOX CONNECTOR HOLE 3/4 NPT FEMALE THREAD. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. 1 1/2-11 1/2 NPSC FEMALE THREAD BOTH PORTS Part/Model Number EN523M5L EN523M72L CP523FU5LR CP523FU72LR Specification Units TBD Motor Enclosure - Shaft Mtl. - Explosion-proof-CS Explosion-proof-CS CHEM XP-SS CHEM XP-SS Horsepower Phase - Frequency Voltage - Single-6 hz Three-6 hz Single-6 hz Three-6 hz Motor Nameplate Amps AC 23 23/ /46 Max. Blower Amps Amps (A) / /3.7 Locked Rotor Amps Amps (A) / /4 Service Factor Amps (A) / /31 Starter Size - 1 / 1 / Thermal Protection XP Motor Class - Group - Class B - Pilot Duty Class B - Pilot Duty Class B - Pilot Duty Class B - Pilot Duty - I-D I-D I-D I-D Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. XP Motor Class - Group - See Explosive Atmosphere Classification Chart in Section I USA: Europe: Asia: D 13

86 Environmental / Chemical Processing Blowers EN 523 & CP HP High Pressure Sealed Regenerative w/explosion-proof Motor FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 14 IWG Maximum vacuum: 135 IWG Standard motor: 3. HP, explosion-proof Cast aluminum blower housing, impeller, cover & manifold; cast iron UL & CSA approved motor with permanently sealed ball bearings for explosive gas atmospheres Class I Group D minimum Sealed blower assembly Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz EN EN USA: Europe: Asia: D 14

87 Environmental / Chemical Processing Blowers EN 6 & CP 6 5. HP Sealed Regenerative w/explosion-proof Motor L /2 NPSC FEMALE THREAD BOTH PORTS OUT MM NOTES 1 TERMAL BOX CONNECTOR HOLE 3/4 NPT FEMALE THREAD POSITIONED AT 12 O CLOCK. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN NOTE DIA (4) MTG. HOLES MODEL EN6F72L EN6F5L L (/MM) 2.5/ /529.2 Part/Model Number EN6F5L EN6F72L EN6F86L CP6FW5LR CP6FW72LR Specification Units TBD Motor Enclosure - Shaft Mtl. - Explosion-proof-CS Explosion-proof-CS Explosion-proof-CS CHEM XP-SS CHEM XP-SS Horsepower Phase - Frequency Voltage - Single-6 hz Three-6 hz Three-6 hz Single-6 hz Three-6 hz Motor Nameplate Amps AC 23 23/ /46 Max. Blower Amps Amps (A) / /7 Locked Rotor Amps Amps (A) 23 14/ /7 Service Factor Amps (A) 1 152/ /76 Starter Size - 2 1/ 2 1/ Thermal Protection XP Motor Class - Group - Class B - Pilot Duty Class B - Pilot Duty Class B - Pilot Duty Class B - Pilot Duty Class B - Pilot Duty - I-D, II-F&G I-D, II-F&G I-D, II-F&G I-D, II-F&G I-D, II-F&G Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. XP Motor Class - Group - See Explosive Atmosphere Classification Chart in Section I USA: Europe: Asia: D 15

88 Environmental / Chemical Processing Blowers EN 6 & CP 6 5. HP Sealed Regenerative w/explosion-proof Motor FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 11 IWG Maximum vacuum: 85 IWG Standard motor: 5. HP, explosion-proof Cast aluminum blower housing, impeller, cover & manifold; cast iron UL & CSA approved motor with permanently sealed ball bearings for explosive gas atmospheres Class I Group D minimum Sealed blower assembly Quiet operation within OSHA standards Muffler included (part# ) MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves External mufflers for additional silencing Air knives (used on blow-off applications) Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz EN6F72L EN6F5L EN6F72L EN6F5L USA: Europe: Asia: D 16

89 Environmental / Chemical Processing Blowers EN / CP HP High Pressure Sealed Regenerative w/explosion-proof Motor A C DIRECTION OF ROTATION B ROTATION OUT MM (2X) D MTG. HOLE DETAIL (4X) 2" /2 NPSC FEMALE THREAD BOTH PORTS NOTES MODEL A B C D 1 TERMAL BOX CONNECTOR HOLE 3/4 NPT FEMALE THREAD. EN DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. EN Part/Model Number EN633BA72LM CP633FY72LR Specification Units Motor Enclosure - Shaft Mtl. - XP-CS CHEM XP-SS Horsepower Voltage AC 28-23/ /46 Phase - Frequency - Three - 6 Hz Three - 6 Hz Insulation Class - B B NEMA Rated Motor Amps Amps (A) 2-18/ /9.3 Service Factor Max. Blower Amps Amps (A) 17/8.5 17/8.5 Locked Rotor Amps Amps (A) 177/ /88.7 Starter Size - 1/1 1/1 Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. XP Motor Class - Group - See Explosive Atmosphere Classification Chart in Section I USA: Europe: Asia: D 17

90 Environmental / Chemical Processing Blowers EN / CP HP High Pressure Sealed Regenerative w/explosion-proof Motor FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 2/195 IWG Maximum vacuum: 155/155 IWG Standard motor: 7.5 HP, explosion-proof Cast aluminum blower housing, impeller, cover & manifold; cast iron UL & CSA approved motor with permanently sealed ball bearings for explosive gas atmospheres Class I Group D minimum Sealed blower assembly Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz USA: Europe: Asia: D 18

91 Environmental / Chemical Processing Blowers EN 656 & CP HP Sealed Regenerative w/explosion-proof Motor STD. DIRECTION OF ROTATION MM (4X) MTG HOLES NOTES 1 TERMAL BOX CONNECTOR HOLE 3/4 NPT. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN " NPSC STRAIGHT THDS BOTH PORTS Part/Model Number EN656M5XL EN656M72XL EN656M86XL CP656FU72XLR Specification Units Motor Enclosure - Shaft Mtl. - Explosion-proof-CS Explosion-proof-CS Explosion-proof-CS CHEM XP-SS Horsepower Phase - Frequency - Single-6 hz Three-6 hz Three-6 hz Three-6 hz Voltage AC / /46 Motor Nameplate Amps Amps (A) / /3.7 Max. Blower Amps Amps (A) 17 1/ /5 Locked Rotor Amps Amps (A) / /27 Service Factor - 1 / / Starter Size Thermal Protection - Class B - Pilot Duty Class B - Pilot Duty Class B - Pilot Duty Class B - Pilot Duty XP Motor Class - Group - I-D, II-F&G I-D, II-F&G I-D, II-F&G I-D, II-F&G Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. XP Motor Class - Group - See Explosive Atmosphere Classification Chart in Section I USA: Europe: Asia: D 19

92 Environmental / Chemical Processing Blowers EN 656 & CP HP Sealed Regenerative w/explosion-proof Motor FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: IWG Maximum vacuum: 73 IWG Standard motor: 3. HP, explosion-proof Cast aluminum blower housing, impeller, cover & manifold; cast iron UL & CSA approved motor with permanently sealed ball bearings for explosive gas atmospheres Class I Group D minimum Sealed blower assembly Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz EN656M72XL EN656M5XL EN656M72XL EN656M5XL USA: Europe: Asia: D 2

93 Environmental / Chemical Processing Blowers EN 7 Single-Phase and CP Options Sealed Regenerative Blower w/explosion-proof Motor OUT ROTATION DIRECTION 2 1/2" NPSC FEMALE THREADS BOTH PORTS MM NOTES 1 TERMAL BOX CONNECTOR HOLE 3/4 NPT FEMALE THREAD. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.. X 2. SLOT 19/5.8 (4) PLACES Part/Model Number EN7FL5MWL CP7FX5MWLR Specification Units Motor Enclosure - Shaft Mtl. - Explosion-proof-CS CHEM XP-SS Horsepower Phase - Frequency - Single-6 hz Single-6 hz Voltage AC Motor Nameplate Amps Amps (A) Max. Blower Amps Amps (A) Locked Rotor Amps Amps (A) Service Factor Starter Size Thermal Protection - Class B - Pilot Duty Class B - Pilot Duty XP Motor Class - Group - I-D I-D Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. XP Motor Class - Group - See Explosive Atmosphere Classification Chart in Section I USA: Europe: Asia: D 21

94 Environmental / Chemical Processing Blowers EN 7 Single-Phase and CP Options Sealed Regenerative Blower w/explosion-proof Motor FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 8 IWG Maximum vacuum: IWG Standard motor: 5. HP, explosion-proof Cast aluminum blower housing, impeller, cover & manifold; cast iron UL & CSA approved motor with permanently sealed ball bearings for explosive gas atmospheres Class I Group D minimum Sealed blower assembly Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz EN7FL5WL USA: Europe: Asia: D 22

95 NAMEPLATE MOTOR Environmental / Chemical Processing Blowers EN 7 & CP 7 3. / 5. HP Sealed Regenerative w/explosion-proof Motor L ROTATION DIRECTION MODEL: PART NO /2" NPSC FEMALE THREADS BOTH PORTS OUT.88 MM R NOTES 1 TERMAL BOX CONNECTOR HOLE. NPT. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN C L OF BLOWER MODEL EN7M72XL EN7F72XL L (/MM) 19.72/ /533.4 Part/Model Number EN7M72XL EN7M86XL EN7F72XL CP7FW72XLR CP7FU72XLR Specification Units Motor Enclosure - Shaft - XP-CS XP-CS XP-CS CHEM XP-SS CHEM XP-SS Mtl. Horsepower Voltage AC 28-23/ / / /46 Phase - Frequency - Three-6 Hz Three-6 Hz Three - 6 Hz Three-6 Hz Three - 6 Hz Insulation Class - B B B B B NEMA Rated Motor Amps Amps (A) 7.2/ /7 14/7 7.2/3.6 Service Factor Maximum Blower Amps Amps (A) 1/ /7.5 15/7.5 1/5 Locked Rotor Amps Amps (A) 54/ /76 152/76 54/27 Starter Size - / 1/1 1/1 / Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. XP Motor Class - Group - See Explosive Atmosphere Classification Chart in Section I USA: Europe: Asia: D 23

96 Environmental / Chemical Processing Blowers EN 7 & CP 7 3. / 5. HP Sealed Regenerative w/explosion-proof Motor FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 8 IWG Maximum vacuum: IWG Standard motor: 5. HP, explosion-proof Cast aluminum blower housing, impeller, cover & manifold; cast iron UL & CSA approved motor with permanently sealed ball bearings for explosive gas atmospheres Class I Group D minimum Sealed blower assembly Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz EN7F72XL EN7M72XL EN7F72XL EN7M72XL USA: Europe: Asia: D 24

97 Environmental / Chemical Processing Blowers EN 88 Single-Phase and CP Options Sealed Regenerative Blower w/explosion-proof Motor OUT ROTATION DIRECTION 2 1/2" NPSC FEMALE THREADS BOTH PORTS MM NOTES 1 TERMAL BOX CONNECTOR HOLE 3/4 NPT FEMALE THREAD. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN.. X 2. SLOT 19/5.8 (4) PLACES Part/Model Number EN7FL5MWL EN88FL5MWL CP7FX5MWLR CP88FX5MWLR Specification Units Motor Enclosure - Shaft Mtl. - Explosion-proof-CS Explosion-proof-CS CHEM XP-SS CHEM XP-SS Horsepower Phase - Frequency - Single-6 hz Single-6 hz Single-6 hz Single-6 hz Voltage AC Motor Nameplate Amps Amps (A) Max. Blower Amps Amps (A) Locked Rotor Amps Amps (A) Service Factor Starter Size Thermal Protection - Class B - Pilot Class B - Pilot Class B - Pilot Class B - Pilot XP Motor Class - Group - Duty I-D Duty I-D Duty I-D Duty I-D Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. XP Motor Class - Group - See Explosive Atmosphere Classification Chart in Section I USA: Europe: Asia: D 25

98 Environmental / Chemical Processing Blowers EN 88 Single-Phase and CP Options Sealed Regenerative Blower w/explosion-proof Motor FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 8 IWG Maximum vacuum: IWG Standard motor: 5. HP, explosion-proof Cast aluminum blower housing, impeller, cover & manifold; cast iron UL & CSA approved motor with permanently sealed ball bearings for explosive gas atmospheres Class I Group D minimum Sealed blower assembly Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz EN88FL5MWL USA: Europe: Asia: D 26

99 Environmental / Chemical Processing Blowers EN 88 & CP 88 Three-Phase Sealed Regenerative Blower w/explosion-proof Motor ROTATION DIRECTION NOTE OUT MM NOTES 1 TERMAL BOX CONNECTOR HOLE. NPT CONDUIT. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN DIA (8) MTG. HOLES /2-8 NPSC FEMALE THREAD BOTH PORTS Part/Model Number EN88BA72MXL EN88BA86MXL CP88FY72MXLR Specification Units Motor Enclosure - Shaft Mtl. - Explosion-proof-CS Explosion-proof-CS CHEM XP-SS Horsepower Phase - Frequency - Three-6 hz Three-6 hz Three-6 hz Voltage AC 23/ /46 Motor Nameplate Amps Amps (A) 18.6/ /9.3 Max. Blower Amps Amps (A) 22./ /11. Locked Rotor Amps Amps (A) 126/ /63 Service Factor - 1/1 1 1/1 Starter Size Thermal Protection - Class B - Pilot Duty Class B - Pilot Duty Class B - Pilot Duty XP Motor Class - Group - I-D, II-F&G I-D, II-F&G I-D, II-F&G Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. XP Motor Class - Group - See Explosive Atmosphere Classification Chart in Section I USA: Europe: Asia: D 27

100 Environmental / Chemical Processing Blowers EN 88 & CP 88 Three-Phase Sealed Regenerative Blower w/explosion-proof Motor FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 85 IWG Maximum vacuum: 9 IWG Standard motor: 7.5 HP, explosion-proof Cast aluminum blower housing, impeller, cover & manifold; cast iron UL & CSA approved motor with permanently sealed ball bearings for explosive gas atmospheres Class I Group D minimum Sealed blower assembly Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves External mufflers for additional silencing Air knives (used on blow-off applications) Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz EN EN USA: Europe: Asia: D 28

101 Environmental / Chemical Processing Blowers EN / CP HP High Pressure Sealed Regenerative w/explosion-proof Motor 1.3 A 26.2 C DIRECTION OF ROTATION B ROTATION OUT (2X) D " /2 NPSC FEMALE THREAD BOTH PORTS MM MTG. HOLE DETAIL (4X) NOTES 1 TERMAL BOX CONNECTOR HOLE 3/4 NPT FEMALE THREAD. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. MODEL A B C D EN EN Part/Model Number EN833BA72LM CP833FY72LRM Specification Units Motor Enclosure - Shaft Mtl. - XP-CS CHEM XP-SS Horsepower Voltage AC 28-23/ /46 Phase - Frequency - Three - 6 Hz Three - 6 Hz Insulation Class - B B NEMA Rated Motor Amps Amps (A) 2-18/ /9.3 Service Factor Max. Blower Amps Amps (A) 19/9.5 19/9.5 Locked Rotor Amps Amps (A) 177/ /88.7 Starter Size - 1/1 1/1 Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. XP Motor Class - Group - See Explosive Atmosphere Classification Chart in Section I USA: Europe: Asia: D 29

102 Environmental / Chemical Processing Blowers EN / CP HP High Pressure Sealed Regenerative w/explosion-proof Motor FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 2/195 IWG Maximum vacuum: 155/155 IWG Standard motor: 7.5 HP, explosion-proof Cast aluminum blower housing, impeller, cover & manifold; cast iron UL & CSA approved motor with permanently sealed ball bearings for explosive gas atmospheres Class I Group D minimum Sealed blower assembly Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz Inches of Water USA: Europe: Asia: D 3

103 Environmental / Chemical Processing Blowers EN 858 & CP / 1. HP Sealed Regenerative w/explosion-proof Motor L /2" NPSC FEMALE THREAD BOTH PORTS ROTATION DIRECTION OUT NOTE 1 MM NOTES 1 TERMAL BOX CONNECTOR HOLE 3/4 NPT. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN MODEL L (/MM) EN858BA72WL 23.65/6.7 EN858BD72WL 26./66.4 Part/Model Number EN858BD72WL EN858BD86WL EN858BA72WL CP858FZ72WLR Specification Units Motor Enclosure - Shaft Mtl. - Explosion-proof-CS Explosion-proof-CS Explosion-proof-CS CHEM XP-SS Horsepower Phase - Frequency - Three-6 hz Three-6 hz Three-6 hz Three-6 hz Voltage AC 23/ /46 23/46 Motor Nameplate Amps Amps (A) 24/ /9.3 24/12 Max. Blower Amps Amps (A) 3/ /13 3/15 Locked Rotor Amps Amps (A) 234/ /63 234/117 Service Factor - 2/1 1 1/1 2/1 Starter Size Thermal Protection - Class B - Pilot Duty Class B - Pilot Duty Class B - Pilot Duty Class B - Pilot Duty XP Motor Class - Group - I-D, II-F&G I-D, II-F&G I-D, II-F&G I-D, II-F&G Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. XP Motor Class - Group - See Explosive Atmosphere Classification Chart in Section I USA: Europe: Asia: D 31

104 Environmental / Chemical Processing Blowers EN 858 & CP / 1. HP Sealed Regenerative w/explosion-proof Motor FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 12 IWG Maximum vacuum: 95 IWG Standard motor: 1 HP, explosion-proof Cast aluminum blower housing, impeller, cover & manifold; cast iron UL & CSA approved motor with permanently sealed ball bearings for explosive gas atmospheres Class I Group D minimum Sealed blower assembly Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz EN858D72WL EN858BA72WL EN858D72WL EN858BA72WL USA: Europe: Asia: D 32

105 EN99BG72WL Environmental / Chemical Processing Blowers EN 99 & CP / 15. HP Sealed Regenerative w/explosion-proof Motor L OUT 4-8 NPSC FEMALE THREAD BOTH PORTS ROTATION DIRECTION MM NOTES 1 TERMAL BOX CONNECTOR HOLE 1 1/4 NPT FEMALE THREAD. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN SEE NOTE 1. X 2. SLOT (4) PLACES MODEL L(/MM) EN99BG72WL 3.17/766.3 EN99DB72WL 23.66/61. Part/Model Number EN99BG72WL EN99BG86WL EN99BD72WL CP99GA72WLR Specification Units Motor Enclosure - Shaft Mtl. - Explosion-proof-CS Explosion-proof-CS Explosion-proof-CS CHEM XP-SS Horsepower Phase - Frequency - Three-6 hz Three-6 hz Three-6 hz Three-6 hz Voltage AC 23/ /46 23/46 Motor Nameplate Amps Amps (A) 36/ /12 36/18 Max. Blower Amps Amps (A) 48/ /16 48/24 Locked Rotor Amps Amps (A) 24/ /117 24/12 Service Factor - 2/2 2 2/1 2/2 Starter Size Thermal Protection - Class B - Pilot Duty Class B - Pilot Duty Class B - Pilot Duty Class B - Pilot Duty XP Motor Class - Group - I-D, II-F&G I-D, II-F&G I-D, II-F&G I-D, II-F&G Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. XP Motor Class - Group - See Explosive Atmosphere Classification Chart in Section I USA: Europe: Asia: D 33

106 Environmental / Chemical Processing Blowers EN 99 & CP / 15. HP Sealed Regenerative w/explosion-proof Motor FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 14 IWG Maximum vacuum: 112 IWG Standard motor: 15 HP, explosion-proof Cast aluminum blower housing, impeller, cover & manifold; cast iron UL & CSA approved motor with permanently sealed ball bearings for explosive gas atmospheres Class I Group D minimum Sealed blower assembly Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz EN99BG72WL EN99BD72WL EN99BG72WL EN99BD72WL USA: Europe: Asia: D 34

107 Environmental / Chemical Processing Blowers EN 979 & CP HP Sealed Regenerative w/explosion-proof Motor 1.5 DIA. (38.1) LIFTG LUG OUT " NPSC PORTS ROTATION DIRECTION MM NOTES TERMAL BOX CONNECTOR HOLE 1 1/4 NPT FEMALE THREAD. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN Part/Model Number EN979BK72WL EN979BK86WL CP979GB72WLR Specification Units Motor Enclosure - Shaft Mtl. - Explosion-proof-CS Explosion-proof-CS CHEM XP-SS Horsepower Phase - Frequency Voltage - Three-6 hz Three-6 hz Three-6 hz Motor Nameplate Amps AC 23/ /46 Max. Blower Amps Amps (A) 46/ /23 Locked Rotor Amps Amps (A) 6/3 24 6/3 Service Factor Amps (A) 334/ /167 Starter Size - 3/2 2 3/2 Thermal Protection XP Motor Class - Group - Class B - Pilot Duty Class B - Pilot Duty Class B - Pilot Duty - I-D, II-F&G I-D, II-F&G I-D, II-F&G Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. XP Motor Class - Group - See Explosive Atmosphere Classification Chart in Section I USA: Europe: Asia: D 35

108 Environmental / Chemical Processing Blowers EN 979 & CP HP Sealed Regenerative w/explosion-proof Motor FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 9 IWG Maximum vacuum: 9 IWG Standard motor: 2 HP, explosion-proof Cast aluminum blower housing, impeller, cover & manifold; cast iron UL & CSA approved motor with permanently sealed ball bearings for explosive gas atmospheres Class I Group D minimum Sealed blower assembly Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz EN EN USA: Europe: Asia: D 36

109 Environmental / Chemical Processing Blowers EN 14 & CP / 3. HP Sealed Regenerative w/explosion-proof Motor OUT NPSC FEMALE THREAD BOTH PORTS (CAST IRON) ROTATION DIRECTION MM NOTES L 1 TERMAL BOX CONNECTOR HOLE 1 1/4 NPT FEMALE THREAD. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. SLOTS. x 2. (19.1 x 5.8) 4X PLACES MODEL LENGTH (/MM) EN14BK72MWL 32.12/815.9 EN14DX72MWL /792.1 Part/Model Number EN14BK72MWL EN14DX72MWL EN14DX86MWL CP14GB72MWLR CP14GC72MWLR Specification Units TBD Motor Enclosure - Shaft Mtl. - Explosion-proof-CS Explosion-proof-CS Explosion-proof-CS CHEM XP-SS CHEM XP-SS Horsepower Phase - Frequency Voltage - Three-6 hz Three-6 hz Three-6 hz Three-6 hz Three-6 hz Motor Nameplate Amps AC 23/ / / /46 Max. Blower Amps Amps (A) 46/23-66/ /23-66/33 Locked Rotor Amps Amps (A) 6/3 82/ /3 82/41 Service Factor Amps (A) 294/ / / /224 Starter Size - 3//2 3/3 3 3/2 3/3 Thermal Protection XP Motor Class - Group - Class B - Pilot Duty Class B - Pilot Duty Class B - Pilot Duty Class B - Pilot Duty Class B - Pilot Duty - I-D, II-F&G I-D, II-F&G I-D, II-F&G I-D, II-F&G I-D, II-F&G Shipping Weight Lbs Kg Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 3 phase motors are factory tested and certified to operate on both: 28-23/ VAC-3 ph-6 Hz and 19-28/ VAC-3 ph-5 Hz. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. XP Motor Class - Group - See Explosive Atmosphere Classification Chart in Section I USA: Europe: Asia: D 37

110 Environmental / Chemical Processing Blowers EN 14 & CP / 3. HP Sealed Regenerative w/explosion-proof Motor FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 144 IWG Maximum vacuum: 115 IWG Standard motor: 3 HP, explosion-proof Cast aluminum blower housing, impeller, cover & manifold; cast iron UL & CSA approved motor with permanently sealed ball bearings for explosive gas atmospheres Class I Group D minimum Sealed blower assembly Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz EN14DX72MWL EN14BK72MWL EN14DX72MWL EN14BK72MWL USA: Europe: Asia: D 38

111

112 Remote Drive (Motor-less) Blowers AMETEK Technical & Industrial Products ROTRON brand has long been a world leader in regenerative blower technologies, bringing regenerative advantages to a new level, providing quiet, maintenance-free, oil-free operation. Our industrial (_RD) Remote Drive Blowers are motorless models built with DR/EN/CP/SL blower features and include: Rugged cast-iron arbor and bearing suspension system Oversized shaft to withstand heavy-duty side loads Precision balanced impellers for low vibration operation High speed versions built with heat treated impellers available. USA: Europe: Asia:

113 Remote Drive (Motorless) Blowers MF573RD A ROTATION B C AIR E F AIR OUT NOTES D 1 CONTACT FACTORY FOR PULLEY OPTIONS. 2 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 3 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. G Specification /MM Model Number Part Number A B C D E F G MF573RD Pressure Blower Performance at Standard Conditions Suction , RPM 14, RPM , RPM 1, RPM , RPM 1, RPM Input Horsepower.8.4 1, RPM 14, RPM 12, RPM Input Horsepower.8.4 1, RPM 14, RPM 12, RPM Do not exceed maximum speed shown on each graph. Do not exceed maximum speed shown on each graph. USA: Europe: Asia: E 1

114 Remote Drive (Motorless) Blowers SL2RD B J K E 4 MTG HOLES Q L G N OUT ROTATION P S FLAT C F T 4 MTG HOLES (SAME AS OPPOSITE SIDE) NOTES 1 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. A H D 1/4-2 UNC - 2B X 44 4 HOLES EQ SPACED ON 4.43 DIA R Specification /MM Model Number Part Number A B C D E F G H J K L M N P Q R S T SL2RD Pressure Blower Performance at Standard Conditions Suction C AIR AT 1 C 5 C 25 C 35 RPM 3 RPM 25 RPM 45 RPM 4 RPM 5 RPM 55 RPM 6 RPM AIR AT 1 C 3 RPM 25 RPM C 5 C 4 RPM 35 RPM 45 RPM 55 RPM 5 RPM 25 C 6 RPM Input Horsepower RPM 3 RPM 25 RPM Do not exceed maximum speed shown on each graph or 1 C. Do not exceed maximum speed shown on each graph or 1 C. 35 RPM 4 RPM 45 RPM 5 RPM 55 RPM 6 RPM Input Horsepower 3 RPM 35 RPM 4 RPM 45 RPM 5 RPM 55 RPM 6 RPM USA: Europe: Asia: E 2

115 Remote Drive (Motorless) Blowers DR/EN/CP 44RD B B A A M NPSC L E KEY D F D E KEY F N P OUT ROTATION C C G G Q K J TYP H DIA. TYP 4 MTG HOLES K J TYP H DIA. TYP 4 MTG HOLES DR MODELS EN MODELS DR/EN MODELS NOTES 1 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. R Specification /MM Model Number Part Number A B C D E F G J H K L M N P Q R DR44RDNT EN44RDML Pressure Blower Performance at Standard Conditions Suction AIR AT 1 C C 5 C 6 25 C 4 55 RPM 45 RPM 65 RPM AIR AT 1 C C 5 C 6 25 C 4 55 RPM 65 RPM RPM RPM 1 RPM 35 RPM 45 RPM 5 25 RPM 35 RPM Input Horsepower Do not exceed maximum speed shown on each graph or 1 C. Input Horsepower Do not exceed maximum speed shown on each graph or 1 C. USA: Europe: Asia: E 3

116 Remote Drive (Motorless) Blowers DR/EN/CP 55RD B B A A M NPSC L E KEY D F D E KEY F N P OUT ROTATION C C G G Q K J TYP H DIA. TYP 4 MTG HOLES K J TYP H DIA. TYP 4 MTG HOLES DR MODELS EN MODELS DR/EN MODELS NOTES 1 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. R Specification /MM Model Number Part Number A B C D E F G J H K L M N P Q R DR55RDNT EN55RDML Pressure Blower Performance at Standard Conditions Suction Input Horsepower RPM 25 RPM 1 35 RPM RPM 45 RPM RPM AIR AT 1 C 45 C 5 C 25 C Do not exceed maximum speed shown on each graph or 1 C Input Horsepower RPM 25 RPM 1 AIR AT 1 C 35 RPM RPM C 45 RPM 5 C RPM 25 C Do not exceed maximum speed shown on each graph or 1 C USA: Europe: Asia: E 4

117 Remote Drive (Motorless) Blowers DR/EN/CP 513RD B B A A M NPSC L E KEY D F D E KEY F N P OUT ROTATION C C G G Q K J TYP H DIA. TYP 4 MTG HOLES K J TYP H DIA. TYP 4 MTG HOLES DR MODELS EN MODELS DR/EN MODELS NOTES 1 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. R Specification /MM Model Number Part Number A B C D E F G J H K L M N P Q R DR513RDNT 3876 EN513RDL Pressure Blower Performance at Standard Conditions Suction RPM 1 C C 5 C 25 C C C 5 C 25 C RPM 6 RPM 3 25 RPM 35 RPM 45 RPM 6 RPM 25 RPM 55 RPM RPM Input Horsepower Do not exceed maximum speed shown on each graph or 1 C. Input Horsepower Do not exceed maximum speed shown on each graph or 1 C. USA: Europe: Asia: E 5

118 Remote Drive (Motorless) Blowers DR/EN/CP 523RD B B A A M NPSC L E KEY D F D E KEY F N P OUT ROTATION C C G G Q K J TYP H DIA. TYP 4 MTG HOLES K J TYP H DIA. TYP 4 MTG HOLES DR MODELS EN MODELS DR/EN MODELS NOTES 1 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. R Specification /MM Model Number Part Number A B C D E F G J H K L M N P Q R DR523RDNT EN523RDL Pressure Blower Performance at Standard Conditions Suction AIR AT 1 C RPM C 5 C 25 C RPM 35 RPM 45 RPM 55 RPM AIR AT 5 C 6 RPM C 1 1 RPM 35 RPM 45 RPM 55 RPM 6 RPM RPM Input Horsepower Do not exceed maximum speed shown on each graph or 1 C. Input Horsepower Do not exceed maximum speed shown on each graph or 1 C. USA: Europe: Asia: E 6

119 Remote Drive (Motorless) Blowers DR/EN/CP 6RD B B A A M NPSC L E KEY D F D E KEY F N P OUT ROTATION C C G G Q K J TYP H DIA. TYP 4 MTG HOLES K J TYP H DIA. TYP 4 MTG HOLES DR MODELS EN MODELS DR/EN MODELS NOTES 1 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. R Specification /MM Model Number Part Number A B C D E F G J H K L M N P Q R DR6RDNT EN6RDL* Pressure Blower Performance at Standard Conditions Suction AIR AT 1 C 45 RPM C 5 C 55 RPM RPM AIR AT 1 C C 5 C 45 RPM 55 RPM C 3 25 RPM 25 C 1 RPM 25 RPM 35 RPM RPM Input Horsepower Do not exceed maximum speed shown on each graph or 1 C. 55 Input Horsepower Do not exceed maximum speed shown on each graph or 1 C. * Dual mufflers provided in place of muffler tower. USA: Europe: Asia: E 7

120 Remote Drive (Motorless) Blowers DR/EN/CP 656RD B B A A M NPSC L E KEY D F D E KEY F N P OUT ROTATION C C G G Q K J TYP H DIA. TYP 4 MTG HOLES K J TYP H DIA. TYP 4 MTG HOLES DR MODELS EN MODELS DR/EN MODELS NOTES 1 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. R Specification /MM Model Number Part Number A B C D E F G J H K L M N P Q R DR656RDNT 861 EN656RDL Pressure Blower Performance at Standard Conditions Suction C C C RPM 55 RPM 6 RPM C RPM 35 RPM 45 RPM 55 RPM 6 RPM 5 C RPM 35 RPM 45 RPM RPM Input Horsepower Do not exceed maximum speed shown on each graph or 1 C. Input Horsepower Do not exceed maximum speed shown on each graph or 1 C. USA: Europe: Asia: E 8

121 Remote Drive (Motorless) Blowers DR/EN/CP 7RD B B A A M NPSC L E KEY D F D E KEY F N P OUT ROTATION C C G G Q K J TYP H DIA. TYP 4 MTG HOLES K J TYP H DIA. TYP 4 MTG HOLES DR MODELS EN MODELS DR/EN MODELS NOTES 1 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. R Specification /MM Model Number Part Number A B C D E F G J H K L M N P Q R DR7RDNT EN7RDML Pressure Blower Performance at Standard Conditions Suction AIR AT 1 C AIR AT 1 C RPM 35 RPM 299 C C 55 RPM C 45 RPM 5 C 55 RPM RPM RPM 35 RPM Input Horsepower Do not exceed maximum speed shown on each graph or 1 C. 55 Input Horsepower Do not exceed maximum speed shown on each graph or 1 C. 55 USA: Europe: Asia: E 9

122 Remote Drive (Motorless) Blowers DR/EN/CP 858RD B B A A M NPSC L E KEY D F D E KEY F N P OUT ROTATION C C G G Q K J TYP H DIA. TYP 4 MTG HOLES K J TYP H DIA. TYP 4 MTG HOLES DR MODELS EN MODELS DR/EN MODELS NOTES 1 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. R Specification /MM Model Number Part Number A B C D E F G J H K L M N P Q R DR858RDNT EN858RDL Pressure Blower Performance at Standard Conditions Suction AIR AT 1 C C 5 C 4 RPM C AIR AT 1 C C 35 RPM 5 C 4 RPM RPM 25 RPM 35 RPM 3 1 RPM 25 RPM 25 C Input Horsepower Do not exceed maximum speed shown on each graph or 1 C. 4 Input Horsepower Do not exceed maximum speed shown on each graph or 1 C. 4 USA: Europe: Asia: E 1

123 Remote Drive (Motorless) Blowers DR/EN/CP 99RD B B A A M NPSC L E KEY D F D E KEY F N P OUT ROTATION C C G G Q K J TYP H DIA. TYP 4 MTG HOLES K J TYP H DIA. TYP 4 MTG HOLES DR MODELS EN MODELS DR/EN MODELS NOTES 1 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. R Specification /MM Model Number Part Number A B C D E F G J H K L M N P Q R DR99RDNT EN99RDL Pressure Blower Performance at Standard Conditions Suction AIR AT 1 C RPM C 5 C 45 RPM AIR AT 1 C C 35 RPM 5 C 45 RPM RPM 1 RPM 25 RPM RPM Input Horsepower Do not exceed maximum speed shown on each graph or 1 C. Input Horsepower Do not exceed maximum speed shown on each graph or 1 C. USA: Europe: Asia: E 11

124 Remote Drive (Motorless) Blowers DR/EN/CP 979RD B B A A M NPSC L E KEY D F D E KEY F N P OUT ROTATION C C G G Q K J TYP H DIA. TYP 4 MTG HOLES K J TYP H DIA. TYP 4 MTG HOLES DR MODELS EN MODELS DR/EN MODELS NOTES 1 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. R Specification /MM Model Number Part Number A B C D E F G J H K L M N P Q R DR979RDNT 876 EN979RDL Pressure Blower Performance at Standard Conditions Suction AIR AT 1 C C C AIR AT 1 C 12 C C RPM 25 RPM 37 RPM 3 1 RPM 25 RPM 37 RPM 35 RPM RPM Input Horsepower Do not exceed maximum speed shown on each graph or 1 C. Input Horsepower Do not exceed maximum speed shown on each graph or 1 C. USA: Europe: Asia: E 12

125 Remote Drive (Motorless) Blowers DR/EN/CP 1233RD N +/-.25 ROTATION B M +/-.25 (2X) H (4X) F.39 1 L +/-.12 (2X) T (4X) R DETAIL AA NOTES 1 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. 3 FILTER # PIECE C +/-.6 SEE DETAIL AA D G +/-.25 E (2X) P NPSC THD K +/-.12 Q +/-.12 A J +/-.12 OUT Specification Model Number Part Number A B C D E F G J H K L M N P Q R T DR1233RD EN1233RDL Pressure Blower Performance at Standard Conditions Suction AIR AT 1 C AIR AT 1 C RPM 35 RPM 4 RPM C 5 C C 5 C 4 RPM 45 RPM RPM RPM 35 RPM Input Horsepower Do not exceed maximum speed shown on each graph or 1 C. Input Horsepower Do not exceed maximum speed shown on each graph or 1 C. This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. E 13 USA: Europe: Asia:

126 Remote Drive (Motorless) Blowers DR/EN/CP 14RD B B A A M NPSC L E KEY D F D E KEY F N P OUT ROTATION C C G G Q K J TYP H DIA. TYP 4 MTG HOLES K J TYP H DIA. TYP 4 MTG HOLES DR MODELS EN MODELS DR/EN MODELS NOTES 1 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. R Specification /MM Model Number Part Number A B C D E F G J H K L M N P Q R DR14RDNT 814 EN14RDL Pressure Blower Performance at Standard Conditions Suction AIR AT 1 C RPM 25 RPM 374 C C RPM 37 RPM RPM AIR AT 1 C C 25 RPM 35 RPM 5 C 37 RPM Input Horsepower Do not exceed maximum speed shown on each graph or 1 C Input Horsepower Do not exceed maximum speed shown on each graph or 1 C USA: Europe: Asia: E 14

127

128 Application Specific Regenerative Blowers Specialty blowers for Commercial Spa, High Temperature, Natural Gas, and Gasoline Vapor Recovery applications. Our industrial NC (Nautilair TM Centraxial) blowers include: Fiberglass or aluminum housing Aluminum impellers Permanently sealed bearings for 5, hours life Our instrument grade and variable flow SE (Minispiral TM Regenerative) blowers include: AC and DC versions available for world voltages and maximum flow variability Glass filled molded phenolic impeller; aluminum and phenolic case 3, hour bearing life Small size and lightweight construction Quiet to NC-47 office equipment standards Our instrument grade SL (Spiral Regenerative) blowers include: Rugged diecast aluminum housing, endbells, and impellers Compact size with encased muffler for maximum noise reduction Low amp draw with highly efficient motor Permanently sealed bearings for 4, hours life Hermetically sealed models designed for glovebox use USA: Europe: Asia:

129 Application Specific Blowers Minispiral Insrument Grade Regenerative Blower DIA MM REF MAX O.D. TYP NOTES 1 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN..44 REF. TYP TYP..25 REF OUT Ø2.24 DIA REF..212 DIA (2) MTG. HOLES Part/Model Number SE2B21 SE62B21 SE2B21A Specification Units Phase - Frequency - Single-5/6 Hz - Single-5/6 Hz Voltage AC 11/ /115 RPM RPM 285/34 285/34 285/34 Insulation Class - B B B Full - Load Amps Amps (A).17/ /.14 Locked Rotor Amps Amps (A).17/ /.15 Shipping Weight Lbs Kg Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. 2 Maximum blower amps corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. USA: Europe: Asia: F 1

130 Application Specific Blowers Minispiral Insrument Grade Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 3.5 IWG Maximum vacuum: 3.5 IWG Maximum ambient: 4 C Shaded pole motor with ball bearings B1 bearing life: 3, hours Weight: 1.1 lb (.5 kg) Envelope size: 4.18 x 1.83 inches (16.2 x 46.5 mm) OPTIONS Sealed units International voltage and frequency (Hz) EQUIVALENT SOUND PRESSURE LEVEL db (re.2 microbar) 3 FEET (.91 METERS) FROM NOISE SOURCE OCTAVE BAND CENTER FREQUENCY Hz NC SOUND POWER LEVEL db (re 1-12 Watts) Blower Performance at Standard Conditions 6 Hz 5 Hz Minispiral Minispiral USA: Europe: Asia: F 2

131 Application Specific Blowers Minispiral MDC Variable Flow Regenerative Blower 2 leads. 2 ga. TFE covered. UL style 118 (12" long, stripped 5") DIA MM REF MAX O.D. TYP REF. TYP NOTES 1 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. 2.9 TYP..25 REF OUT Ø2.24 DIA DIA (2) MTG. HOLES 4.16 REF Part/Model Number SE12V21 SE24V21 Specification Units Voltage Range VDC RPM RPM Insulation Class - B B Full - Load Amps Amps (A) Weight Lbs Kg.4.4 WARNG ON MDC MODEL:EXCEEDG 1. AMP MAY DAMAGE CIRCUIT BOARD. USA: Europe: Asia: F 3

132 Application Specific Blowers Minispiral MDC Variable Flow Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 7./1.3 IWG (15/32 volts) Maximum vacuum: 7./1.3 IWG (15/32 volts) Maximum ambient: 4 C & impeller Shaded pole motor with ball bearings B1 bearing life: 2, - 3, hours Weight:.86 lbs (.39 kg) Envelope size: 4.18 x 1.83 inches (16.2 x 46.5 mm) OPTIONS Sealed blowers for contamination control Electronic speed control db (re.2 microbar) 3 FEET (.91 METERS) FROM NOISE SOURCE OCTAVE BAND CENTER FREQUENCY Hz NC db (re 1-12 Watts) Blower Performance at Standard Conditions 12 V-MDC 24 V-MDC Minispiral MDC Minispiral MDC V-MDC 15 V-MDC V-MDC 32 V-MDC 26 V-MDC V-MDC USA: Europe: Asia: F 4

133 .57 OD 14.5 Application Specific Blowers Minispiral 12/24V HDC Variable Flow Regenerative Blower GA. TFE COVERED UL STYLE " LONG, STRIPPED 1/2" Ø Ø MM OD 19.1 BOTH PORTS NOTES 1 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. Part/Model Number SE12RE21 SE24RE21 Specification Units Voltage Range VDC RPM RPM Insulation Class - B B Full - Load Amps Amps (A) Weight Lbs Kg.5.5 WARNG ON HDC MODEL:MOTOR IS NOT POLARITY PROTECTED. CHECK POLARITY CAREFULL Y BEFORENERGIZG BLOWER. USA: Europe: Asia: F 5

134 Application Specific Blowers Minispiral 12/24V HDC Variable Flow Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant 12 VDC operation: VDC 24 VDC operation: VDC Maximum pressure: 2.7 IWG (15) Maximum vacuum: 2.7 IWG (15) Maximum ambient: 4 C & impeller Brushless DC motor with integrated control electronics Stainless steel ball bearings permanently lubricated for B1 bearing life: 2, - 3, hours Weight: 1.9 lbs (.86 kg) Envelope size: 4.18 x 1.83 inches (16.2 x 46.5 mm) OPTIONS Sealed blowers for contamination control Electronic speed control Low voltage option International voltage and frequency (Hz) EQUIVALENT SOUND PRESSURE LEVEL db (re.2 microbar) 3 FEET (.91 METERS) FROM NOISE SOURCE OCTAVE BAND CENTER FREQUENCY Hz NC SOUND POWER LEVEL db (re 1-12 Watts) Blower Performance at Standard Conditions Minispiral HDC Minispiral HDC V-HDC 15 V-HDC V-HDC LOW VOLTAGE OPERATION 7.5 V-HDC USA: Europe: Asia: F 6

135 .56 ID 14.2 Application Specific Blowers Minispiral 12V HDC Extra Flow / Extra Wide Fat Boy Variable Flow Regenerative Blower GA. TFE COVERED UL STYLE " LONG, STRIPPED 1/4" Ø Ø REF MM OD 19.1 TYP. BOTH PORTS REF. TYP NOTES 1 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. Part/Model Number SE12RE21A Specification Units RPM RPM Voltage Range VDC Insulation Class - B Full - Load Amps Amps (A) Weight Lbs 2.5 Kg 1.1 WARNG ON HDC MODEL:MOTOR IS NOT POLARITY PROTECTED. CHECK POLARITY CAREFULL Y BEFORENERGIZG BLOWER. USA: Europe: Asia: F 7

136 Application Specific Blowers Minispiral 12V HDC Extra Flow / Extra Wide Fat Boy Variable Flow Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 26 IWG (15) Maximum vacuum: 26 IWG (15) Maximum ambient: 4 C Brushless DC motor with integrated control electronics Stainless steel ball bearings permanently lubricated for B1 bearing life: 2, - 3, hours Weight: 1.9 lbs (.86 kg) Compact high performance design: 4.18 x 1.83 inches (16.2 x 46.5 mm) OPTIONS Sealed blowers for contamination control Electronic speed control Low voltage option Speed sensing output (FPS) EQUIVALENT SOUND PRESSURE LEVEL db (re.2 microbar) 3 FEET (.91 METERS) FROM NOISE SOURCE OCTAVE BAND CENTER FREQUENCY Hz NC SOUND POWER LEVEL db (re 1-12 Watts) Blower Performance at Standard Conditions Minispiral HDC Minispiral HDC V-HDC 12 V-HDC 15 V-HDC LOW 1 VOLTAGE 5 OPERATION USA: Europe: Asia: F 8

137 Application Specific Blowers SPIRAL Simplex SL2 Insrument Grade Regenerative Blower OPTIONAL OUTLET TRIMMER OPTIONAL LET TRIMMER /2" CONDUIT HOLE (1) EACH END O.D OUT 1.6 I.D. 4.6 MM TYP UNC -2B X.31 DEEP (4 MOUNTG HOLES EACH END) NOTES 1 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN Part/Model Number SL2P2 SL2P52 SL2P9 Specification Units Motor Enclosure - Shaft Mtl. - ODP-CS ODP-CS ODP-CS Horsepower Voltage AC /46 Phase - Frequency - Single-5/6 Hz Single 6 Hz Three-5/6 Hz Insulation Class - B B B Full - Load Amps Amps (A) 2.45/3.6.95/ /.41 Service Factor Locked Rotor Amps NEMA Amps (A) Starter Size - / / / Shipping Weight Lbs Kg USA: Europe: Asia: F 9

138 Application Specific Blowers SPIRAL Simplex SL2 Insrument Grade Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 32 IWG Maximum vacuum: 31.3 IWG Standard motor:.5 HP, ODP Motor with permanently sealed ball bearings Quiet operation within OSHA standards Thermal overload protection OPTIONS International voltage & frequency (Hz) Hermetically sealed UL & CSA approved motor Remote drive (motorless) model ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Blower Performance at Standard Conditions 6 Hz 5 Hz Spiral SL Spiral SL USA: Europe: Asia: F 1

139 Application Specific Blowers SPIRAL Duplex SL4 Insrument Grade Regenerative Blower 6.56 MAX MAX /2 CONDUIT HOLE (1) EACH END CAPACITORS ON SGLE PHASE MODELS ONLY 13.3 MAX OUT I.D O.D DIA MM 3. TYP UNC-2B X.31 DEEP (6) MOUNTG HOLES EACH END NOTES 1 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. Part/Model Number SL4P2 SL4P52 Specification Units Motor Enclosure - Shaft Mtl. - ODP-CS ODP-CS Horsepower -.. Voltage AC Phase - Frequency - Single-5/6 Hz Single 6 Hz Insulation Class - B B Full - Load Amps Amps (A) 3.7/ /2.2 Service Factor Locked Rotor Amps NEMA Amps (A) Starter Size - / / Shipping Weight Lbs Kg USA: Europe: Asia: F 11

140 Application Specific Blowers SPIRAL Duplex SL4 Insrument Grade Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 6 IWG Maximum vacuum: 55.8 IWG Standard motor:. HP, ODP Motor with permanently sealed ball bearings Quiet operation within OSHA standards Thermal overload protection OPTIONS International voltage & frequency (Hz) Hermetically sealed UL & CSA approved motor Remote drive (motorless) model ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Blower Performance at Standard Conditions 6 Hz 5 Hz Spiral SL Spiral SL USA: Europe: Asia: F 12

141 Application Specific Blowers SPIRAL Duplex SL5 Insrument Grade Regenerative Blower MAX MAX /2" CONDUIT HOLE (1) EACH END CAPACITORS ON SGLE PHASE MODELS ONLY 13.3 MAX OUT I.D O.D DIA MM 3. TYP NOTES 1 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN UNC-2B X.31 DEEP (6) MOUNTG HOLES EACH END Part/Model Number SL5P2 SL5P52 Specification Units Motor Enclosure - Shaft Mtl. - ODP-CS ODP-CS Horsepower -.. Voltage AC Phase - Frequency - Single-5/6 Hz Single 6 Hz Insulation Class - B B Full - Load Amps Amps (A) 4.58/ /2.55 Service Factor Locked Rotor Amps NEMA Amps (A) Starter Size - / / Shipping Weight Lbs Kg USA: Europe: Asia: F 13

142 Application Specific Blowers SPIRAL Duplex SL5 Insrument Grade Regenerative Blower FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 31 IWG Maximum vacuum: 31.3 IWG Standard motor:. HP, ODP Motor with permanently sealed ball bearings Quiet operation within OSHA standards Thermal overload protection OPTIONS International voltage & frequency (Hz) Hermetically sealed UL & CSA approved motor Remote drive (motorless) model ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Blower Performance at Standard Conditions 6 Hz 5 Hz Spiral SL Spiral SL USA: Europe: Asia: F 14

143 Application Specific Blowers Nautilair E E MM 5.38 (136.65) D (REF) 1.23 (31.35) 3.49 (88.) D 1. (44.45) 3.5 (88.9) 1. (44.45) 3.5 (88.9) A A NOTES 1 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. B Ø.4 HOLE (4X) B.495 (12.57) C X KNOCKOUT FOR AIRFLOW SWITCH (BOTH SIDES) W Y TEFC MODEL.495 (12.57) C X KNOCKOUT FOR AIRFLOW SWITCH (BOTH SIDES) Ø7.69 (195.28) W Ø5.19 (131.83) HOLES FOR ELECTRICAL CONNECTIONS 1/4-2 UNC-2B X.5 DP. (4) MTG HOLES EQUALLY SPACED ON A DIA. B.C. 1/4-2 UNC-2B X.5 DP. (4) MTG HOLES STANDARD MODEL Y 1.5 (38.1) H (TYP.) K G V Z J L F R S 2.5 (63.5) AA T K G V Z J L R S 2.53 (64.31) T F (4X) MTG HOLES.28 DIA P U M U M N N O 11.3 (286.96) (4X) MTG HOLES.28 DIA O P (DIA. LET) A B C D E F G H J K L M N O P R S T U V W X Y Z AA NC33A (STD) (293.2) 6.7 (154.2).495 (12.6) 6.4 (153.4) 1.76 (273.3) 5.19 (131.8) 4.25 (18).25 (6.4) 1. (44.5) 5.1 (129.5) 3.13 (79.5) 4. (12.7) 5.59 (142) 5.9 (149.9) 6. (152.4) 1.97 (5) 2.78 (7.6) 7.26 (184.4) 2.38 (6.5) 2.13 (54.1) 2.96 (.2).84 (21.3) 4. (11.6) 2.5 (63.5) --- NC33AE9 (TEFC) (293.2) 6.7 (154.2).495 (12.6) 6.4 (153.4) 1.76 (273.3) 5.19 (131.8) 4.25 (18).25 (6.4) 1. (44.5) 5.1 (129.5) 3.13 (79.5) 4. (12.7) 5.59 (142) 5.9 (149.9) 6. (152.4) 3.52 (89.4) 2.78 (7.6) (339.1) 2.38 (6.5) 2.13 (54.1) 2.96 (.2).84 (21.3) 4. (11.6) 2.5 (63.5) 7.13 (181.1) NC33AG58 (XP) (293.2) 6.7 (154.2).495 (12.6) 6.4 (153.4) 1.76 (273.3) 5.19 (131.8) 4.25 (18).25 (6.4) 1. (44.5) 5.1 (129.5) 3.13 (79.5) 4. (12.7) 5.59 (142) 5.9 (149.9) 6. (152.4) 4.2 (16.7) 2.78 (7.6) (354.1) 2.38 (6.5) 2.13 (54.1) 2.96 (.2).84 (21.3) 4. (11.6) 2.5 (63.5) --- Part/Model Number NC33A2G NC33A3G NC33A33G NC33AE9 NC33AG58 Specification Units Phase - Frequency - Single-5/6 Hz Single-5/6 Hz Three-5/6 Hz Single-5/6 Hz Single-5/6 Hz Voltage AC / /23 115/23 RPM on 5/6 Hz - 29/35 29/35 29/35 29/35 29/35 Insulation Class - B B B F F Full - Load Amps Amps (A) 3.44/ / / / Locked Rotor Amps Amps (A) /1.5 38/19 Shipping Weight Lbs Kg Motor Enclosure - Standard Standard Standard TEFC XP USA: Europe: Asia: F 15

144 Application Specific Blowers Nautilair FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 3.5 IWG Thermoset plastic blower housing with aluminum impeller Permanently seal ball bearings in motor - L1 bearing life: 5, hours Quiet operation within OSHA standards Shipping weight: 18 lbs (8.2 kg) for standard model 28 lbs (12.7 kg) for TEFC model 3 lbs (13.6 kg) for XP model Designed for UL and CSA Automatic thermal overload protection on standard motor enclosures 8 9 EQUIVALENT SOUND PRESSURE LEVEL db (re.2 microbar) 3 FEET (.91 METERS) FROM NOISE SOURCE OCTAVE BAND CENTER FREQUENCY Hz NC33 4,8 1, SOUND POWER LEVEL -12 db (re 1 Watts) Blower Performance at Standard Conditions 6 Hz 5 Hz NC NC USA: Europe: Asia: F 16

145 Application Specific Blowers DR 44/454/55/513/656 Spa Blowers GND LUG F L G MM NOTES 1 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. MODEL DR44AQ58M DR454V58 DR55AW58M DR513V58 DR656K58X E D 1/2-14 NPSM THREAD "P" DIA A I H 2-" NPSC (4) MTG B THREAD HOLES C J A (/MM) B (/MM) C (/MM) D (/MM) E (/MM) F (/MM) G (/MM) H (/MM) I (/MM) J (/MM) K (/MM) L (/MM) 4./ / / / / / / / / / / / / / / / / / / / / / / /367 4./ / / / / / / / / / /15 15./381 4./ / / / / / / / / /349.59/ / / / /325.1 T-BOX 2.25/ / / / / / / / /393.9 Part/Model Number DR44AQ58M DR454V58M DR55AW58M DR513V58 DR656K58X Specification Units Motor Enclosure - Shaft Mtl. - SPA (ODP)-CS SPA (ODP)-CS SPA (ODP)-CS SPA (ODP)-CS TEFC-CS Horsepower Voltage AC 115/23 115/23 115/23 115/23 115/23 Phase - Frequency - Single-5/6 Hz Single-5/6 Hz Single-5/6 Hz Single-5/6 Hz Single-5/6 Hz Insulation Class - F F F F F NEMA Rated Motor Amps Amps (A) 15/ /7.6 21/ /7.6 31/15.5 Service Factor Maximum Blower Amps Amps (A) 8/4 17/8.5 26/13 17/ /13.9 Locked Rotor Amps Amps (A) 32/16 85/43 136/68 85/43 2/1 Recommended NEMA Starter Size- / 1/ 1/ 1/ 1.5/1 Shipping Weight Lbs Kg Recommended Number of Jets Voltage - ROTRON motors are designed to handle a broad range of world voltages and power supply variations. Our dual voltage 1 phase motors are factory tested and certified to operate on both: /28-23 VAC-1 ph-6 Hz and 1-11/2-22 VAC-1 ph-5 Hz. All voltages above can handle a ±1% voltage fluctuation. Special wound motors can be ordered for voltages outside our certified range. Operating Temperatures - Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. Maximum Blower Amps - Corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. Notes - The blower should not be stopped/started more than four times an hour. - Use of relief valve is required for all blowers. USA: Europe: Asia: F 17

146 Application Specific Blowers DR 44/454/55/513/656 Spa Blowers FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant Maximum pressure: 56, 58, 74, 69 or 88 IWG Standard motor: 1., 1.5, 2., 3. HP, Spa Duty ODP (threaded) UL & CSA approved motor with permanently sealed ball bearings and Class B rated thermal protection Quiet operation within OSHA standards MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Remote drive (motorless) models ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Variable frequency drive package Blower Performance at Standard Conditions 6 Hz 5 Hz DR44 DR454 DR55 DR513 DR DR44 DR454 DR55 DR513 DR USA: Europe: Asia: F 18

147 Application Specific Blowers DR 1RDNT/SS1RDNT/HS 1RDNT Remote Drive (Motorless) Blowers Part/Model Number DR1RDNT SS1RDNT HS1RDNT Specification Units Shaft Material - Carbon Steel Stainless Steel Hastelloy Speed Range Housing, Cover, Cover - Cast Iron Stainless Steel Hastelloy Shipping Weight Lbs Kg SS = Stainless Steel HS = Hastelloy 1 DR1RDNT not recommended for use with explosive gas due to material of construction Maximum operating temperature: Blower outlet air temperature should not exceed 26 C (air temperature rise plus inlet temperature). Contact factory for use above 26 C blower outlet air temperature. AMETEK will not be liable for blowers operated beyond factory specific RPM. All applications must be reviewed. Contact application engineering for assistance. USA: Europe: Asia: F 19

148 Application Specific Blowers DR 1RDNT/SS1RDNT/HS 1RDNT Remote Drive (Motorless) Blowers FEATURES Manufactured in the USA - ISO 91 and NAFTA compliant BLOWER OPTIONS Corrosion resistant surface treatments & sealing options Packaged on baseplate with V-belts or coupling, guard & motor High temperature Viton seals Krytox grease high temperature bearings PACKAGE/MOTOR OPTIONS International voltage & frequency (Hz) Packing gland or double faced seal options ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves External mufflers for additional silencing Variable frequency drive package Note: For accessories, special high temperature models may be required Pressure Blower Performance at Standard Conditions Suction AIR T 1 ºC RPM 35 RPM ºC 45 RPM 5 ºC AIR T 1 º C 35 RPM 45 RPM º C 5 º C RPM RPM 1 RPM Input Horsepower Input Horsepower USA: Europe: Asia: F 2

149 Application Specific Blowers MD 11 Magnetic-Drive Regenerative Blower OUTLET LET /2 NPT 2X RESET BUTTON Ø.87 CONDUIT HOLE ROTATION Ø TEFC MOTOR MD11CB4 MODEL SHOWN OUTLET LET Ø.28 MOUNTG HOLE /2 NPT 2X LEADS FAR SIDE.-14 NPT Ø ROTATION MM NOTES DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. XP MOTOR MD11CC4 MODEL SHOWN Ø.28 MOUNTG HOLE 7.1 Part/Model Number MD11CB4 MD11CC4 Specification Units Motor Enclosure - Shaft Mtl. - TEFC Explosion-proof Horsepower Phase - Frequency Voltage - Single-6 hz Single-6 hz Motor Nameplate Amps AC Max. Blower Amps Amps (A) Locked Rotor Amps Amps (A) Service Factor Amps (A) Starter Size Thermal Protection - XP Motor Class - Group - Class B - Automatic, Manual Reset Class B - Automatic - - I-D Shipping Weight Lbs 4 4 Kg Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. F 21 Rev. 2/4 USA: Europe: Asia:

150 Application Specific Blowers MD 11 Magnetic-Drive Regenerative Blower FEATURES Hermetically designed seal-less blower Continuous operation Manufactured in the USA Maximum pressure: 28 IWG Maximum vacuum: 26.5 IWG Standard motor:.25 HP, TEFC or XP Disconnect motor without disassembling from piping Permanently sealed ball bearings in housing and motor Quiet operation within OSHA standards BLOWER OPTIONS Corrosion resistant surface treatments & sealing options ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Pressure Blower Performance at Standard Conditions Suction NATURAL GAS SG =.56 AIR SG = NATURAL GAS SG =.56 AIR SG = USA: Europe: Asia: F 22

151 Application Specific Blowers GVR313 Regenerative Blower ROTATION (TYP.) OUT /2" NPTF (2) PLACES (GVR313) MM NOTES 1 DRAWG NOT TO SCALE, CONTACT FACTORY FOR SCALE CAD DRAWG. 2 CONTACT FACTORY FOR BLOWER MODEL LENGTHS NOT SHOWN. 3 GVR313AK4H MODELS SHOWN BOTTOM VIEW Part/Model Number GVR313AK4H GVR313AK58H GVR313AK72HA GVR313AK91H GVR313AE4HA Specification Units Motor Enclosure - Shaft Mtl. - Explosion-proof - CS Explosion proof - CS Explosion proof - CS ATEX - CS TEFC Horsepower Phase - Frequency Voltage - Single-6 hz Single-5/6 Hz Three-6 Hz Three-5 Hz Single-6 Hz Motor Nameplate Amps AC /22 23/ Max. Blower Amps Amps (A) / / Locked Rotor Amps Amps (A) / / Service Factor Amps (A) / Starter Size Thermal Protection - XP Motor Class - Group - Class B - Automatic Class B - Automatic Class B - Automatic Thermistors Class B - Automatic - I-D 1-D 1-D EExd IIB 1-D Shipping Weight Lbs Kg voltage, 1 phase motors are standard. 23 volt motors available. As an option, a transformer could be used. 2 Maximum operating temperature: Motor winding temperature (winding rise plus ambient) should not exceed 14 C for Class F rated motors or 12 C for Class B rated motors. Blower outlet air temperature should not exceed 14 C (air temperature rise plus inlet temperature). Performance curve maximum pressure and suction points are based on a 4 C inlet and ambient temperature. Consult factory for inlet or ambient temperatures above 4 C. 3 Maximum blower amps corresponds to the performance point at which the motor or blower temperature rise with a 4 C inlet and/or ambient temperature reaches the maximum operating temperature. Rev. 2/4 USA: Europe: Asia: F 23

152 Application Specific Blowers GVR313 Regenerative Blower FEATURES Manufactured in the USA Maximum pressure 45 IWG Maximum vacuum: 4.8 IWG Standard motor:.5 HP, TEFC Anodized cast aluminum blower housing, impeller & cover Quiet operation within OSHA standard ROHS gold irridite coatings on aluminum surfaces MOTOR OPTIONS International voltage & frequency (Hz) BLOWER OPTIONS ACCESSORIES Flowmeters reading in SCFM Filters & moisture separators Pressure gauges, vacuum gauges, & relief valves Pressure Blower Performance at Standard Conditions Suction GVR GVR USA: Europe: Asia: F 24

153

154 Accessories AMETEK Dynamic Fluid Solutions' ROTRON brand has long been a world leader in regenerative blower technologies, bringing regenerative advantages to a new level, providing quiet, maintenance-free, oil-free operation. Our accessories for regenerative blowers inlude: Filtration Accessories Measurement Accessories Noise Reduction Accessories Valves and Gauges VFD Drives Air Knives Blower Model Reference Key A = SPIRAL E = DR/EN/CP656, 6, 633, S7 B= DR/EN/CP68, 83, 11, 22 F = DR/EN/CP 7, 88, 858, S9, nlet P9 (I Only) C= DR/EN/CP33, 312, 313, 353 G= DR/EN/CP833, S13, P13 (Inlet Only) D = DR/EN/CP44, 454, 513, 55, 555, 523 H = DR/EN/CP99, 979, 1233, 14, S15, P15 (Inlet Only) Blower Connection Key NPT American National Standard Taper Pipe Thread (Male) NPSC American National Standard Straight Pipe Thread for Coupling (Female) SO Slip On (Smooth No Threads) USA: Europe: Asia:

155 Accessories Filtration - Inlet Filter (Single Connection) Inlet Filters protect the blower and the air distribution system from dust, and other airborne particles and contaminants. Normally used in pressure systems. B SPECIFICATIONS: HOUSG Steel MEDIA Polyester EFFICIENCY 97-98% (8 to 1 micron particle size) FILTER ELEMENT Replaceable (see filter elements) NOTE: Z MEDIA (1 to 3 micron particle size) available A Ø C Ø Part/Model Number Specification Units Filter Element - A B C, D E E F G H H Ref Blower Model Outlet Connection - 2. SO 1. NPT 1.5 NPT 2. NPT 2. NPT 2.5 NPT 3. NPT 4. NPT 6. NPT Dimension A Inches mm Dimension B Inches mm Dimension C Inches mm Z Media Filter PN Blower Model Reference Key A = SPIRAL E = DR/EN/CP 656, 6, 633, S7 B = DR/EN/CP 68, 83, 11, 22 F = DR/EN/CP 7, 88, 858, S9, P9 (Inlet Only) C = DR/EN/CP 33, 312, 313, 353 G = DR/EN/CP 833, S13, P13 (Inlet Only) D = DR/EN/CP 44, 454, 513, 55, 555, 523 H = DR/EN/CP 99, 979, 1233, 14, S15, P15 (Inlet Only) USA: Europe: Asia: G

156 Accessories Filtration - Inline Filter (Dual Connection) Inline Filters protect the blower from harmful dust and other particles that may be drawn into the blower through the air distribution system. Normally used in vacuum systems. C DIA. A SPECIFICATIONS: HOUSG Steel MEDIA Polyester EFFICIENCY 97-98% (8 to 1 micron particle size) FILTER ELEMENT Replaceable (see filter elements) NOTE: Z MEDIA (1 to 3 micron particle Inline filter PN 2712 is a straight through design Inlet is directly opposite of outlet size) available * Feature 1/4" threaded tap for gauge connection on inlet and outlet D DIA. B Part/Model Number Specification Units * * * Filter Element Ref Blower Model - A B C, D E F G H H Inlet Connection - 1. SO 1. NPSC-F 1.5 NPSC-F 2. NPSC-F 2.5 NPSC-F 3. NPT-M 4. NPT-M 6. NPT-M Outlet Connection - 2. SO 1. NPSC-F 1.5 NPSC-F 2. NPSC-F 2.5 NPSC-F 3. NPT-M 4. NPT-M 6. NPT-M Dimension A Inches mm Dimension B Inches mm Dimension C Inches mm Dimension D Inches mm Z Media Filter PN Blower Model Reference Key A = SPIRAL E = DR/EN/CP 656, 6, 633, S7 B = DR/EN/CP 68, 83, 11, 22 F = DR/EN/CP 7, 88, 858, S9, P9 (Inlet Only) C = DR/EN/CP 33, 312, 313, 353 G = DR/EN/CP 833, S13, P13 (Inlet Only) D = DR/EN/CP 44, 454, 513, 55, 555, 523 H = DR/EN/CP 99, 979, 1233, 14, S15, P15 (Inlet Only) USA: Europe: Asia: G 2

157 Accessories Filtration - Filter Silencers (Single Connection) Filter/Silencers reduce noise levels while ensuring clean air is provided to the blower and the air distribution system. Normally used in pressure applications. B SPECIFICATIONS: HOUSG Steel MEDIA Polyester EFFICIENCY 97-98% (8 to 1 micron size) FILTER ELEMENT Replaceable (see filter elements) A Ø C Ø Part/Model Number Specification Units Filter Element - B C, D E E F G H H Ref Blower Model Outlet Connection - 1. NPT 1.5 NPT 2. NPT 2. NPT 2.5 NPT 3. NPT 4. NPT 6. NPT Dimension A Inches mm Dimension B Inches mm Z Media Filter PN Dimension C Inches mm Blower Model Reference Key A = SPIRAL E = DR/EN/CP 656, 6, 633, S7 B = DR/EN/CP 68, 83, 11, 22 F = DR/EN/CP 7, 88, 858, S9, P9 (Inlet Only) C = DR/EN/CP 33, 312, 313, 353 G = DR/EN/CP 833, S13, P13 (Inlet Only) D = DR/EN/CP 44, 454, 513, 55, 555, 523 H = DR/EN/CP 99, 979, 1233, 14, S15, P15 (Inlet Only) USA: Europe: Asia: G

158 Accessories Filtration - Filter Element All ROTRON Air Filters and Filter/Silencers have replaceable filter elements. The filter media is polyester designed for high efficiency over a wide spectrum of industrial applications. See ÿlter element cross reference table. Filter elements supplied with foam pre-filter. ØID Standard Replacement Filter Element Cross Reference Table Filter Element Filter Element Filter Element HT For DR Blower Models ØOD Part/Model Number Specification Units Z Media Filter PN Dimension ID Inches mm Dimension OD Inches mm Area Sq/Ft Sq/M Dimension HT Inches mm USA: Europe: Asia: G

159 TM TM STALL FLOAT SW. Accessories Filtration - Moisture Separator By separating and containing entrained liquids, ROTRON S moisture separator helps protect our regenerative blowers and the end treatment system from corrosion and mineralization damage. Recommended for all soil vacuum extraction Applications. SPECIFICATIONS: SEPARATION METHOD High Effciency Cyclonic RELIEF VALVE MATERIAL Brass & Stainless Steel FLOAT MATERIAL Copper FLOAT SWITCH SPDT, Explosion-proof NEMA 7&9, 5 Amp max. "A" O.D. LET "A" O.D. 1/4" NPT (PLUGGED) FLOAT LEVEL LET SWITCH 1/4" NPT (PLUGGED) (OPTIONAL) "A" O.D. LET FLOAT LEVEL SWITCH (OPTIONAL) 1/4" NPT (PLUGGED) H applications. H H VACUUM GAUGE (OPTIONAL) VACUUM RELIEF VALVE FLOAT SWITCH (OPTIONAL) 3/4" NPT M OI S T U R E S E P A R AT OR B J D MOISTURE SEPARATOR DRA 3/4" NPT G OUTLET E F WATER LEVEL CAPACITY (PER CHART) VACUUM GAUGE (OPTIONAL) VACUUM RELIEF VALVE MOISTURE SEPARATOR URE T OR CYCLONIC ACTION CAUTION: FREEZG MAY CAUSE DAMAGE. MOISTURE SEPARATORS USED TEMPERATURES BELOW 32øF (øc) MUST BE PROPERLY WTERIZED. FO PACKET DRA 3/4" NPT G OUTLET J B E F J 3.9 (OPTIONAL LOW SWITCH) VACUUM GAUGE (OPTIONAL) VACUUM RELIEF VALVE B G OUTLET D E F D C C DRA - 1" NPT TERNAL THD PLASTIC P DESIGN METAL D DESIGN METAL B DESIGN USA: Europe: Asia: G 5 Part/Model Number MS2PS MS3PS MS35BS MS5BS MS6BS MS1BS Specification Units Dimension A Inches mm CFM Max. CFM m3/hr Dimension B Inches mm Dimension C Inches mm Dimension D Inches mm Dimension E Inches mm Dimension F Inches mm Dimension H Inches mm Dimension G Inches 4.5 OD 4.5 D 4.5 OD 6.63 ID 6.63 ID 8.62 OD mm Dimension J Inches mm Drain Internal Thd - 3/4 3/ Shipping Weight Lbs Kg

160 Accessories Filtration - Moisture Separator 2. Moisture Separator TM Specifications 2.1 Duty The moisture separator shall be designed for use in a soil vapor extraction system capable of continuous operation with a pressure drop of less than six inches of water at the rated flow of _ SCFM. The separator shall be capable of operation under various inlet conditions randing from a fine mist to slugs of water with high efficiency. 2.2 Principle of Operation The moisture separator shall incorporate cyclonic separation to remove entrained water. The separator must protect against an overflow by fail safe mechanical means. An electrical switch or contact(s) alone is not an acceptable means of protection against overflow, but is a good backup. 2.3 Construction The body of the moisture separator shall be constructed of heavy wall plastic or heavy gauge cold rolled steel. The steel interior and exterior shall be epoxy (powder) coated to resist abrasion, corrosion, and chipping that might expose the surface. The inlet shall be tangentially located and welded to the body. The outlet port shall be constructed of PVC or cast aluminum alloy, flanged and sealed to the center of the top of the separator. The separator shall incorporate a non-sparking copper float ball and an adjustable relief valve to protect against overflow and overheating the blower. 2.4 Capacity and Dimension The moisture separator must have a liquid capacity of _ gallons. The inlet shall be _ inch OD slip-on type. The outlet shall be _ inch OD slip-on type. 2.5 Pressure Drop 6 For DR/EN/CP Blower Model Selector Moisture Separator Model Liquidholding Capacity (gallons) Inlet (OD) Outlet Max Vacuum Allow (IHG) MS2PS MS3PS OD MS35BS MS5BS ID 22 MS6BS 4. MS1BS OD 5 Pressure Drop (IWG) MS2PS MS3PS MS35BS MS5BS MS6BS MS1BS Flow Rate (SCFM) USA: Europe: Asia: G 6

161 Accessories Measurement - Air Flow Meter FEATURES Direct reading in SCFM Low pressure drop (2-4" typical) across the flow meter Non-clogging, low impedance air stream Light weight aluminum No moving parts Large easy-to-read dial Accurate within 2% at standard conditions Good repeatability Available in 2", 3" and 4" sizes Factory conÿgured for quick installation.48" Allen key supplied for gauge adjustment OPTIONS Corrosion-resistant version with Chem-Tough or in stainless steel FDA-approved Food Tough surface conversion BENEFITS OPTIMIZE SYSTEM EFFICIENCY Measuring the correct air ow can assist you in ÿne-tuning to your system s optimal efficiency. BALANCE MULTI-PIPG SYSTEMS When evacuating CFM from more than one pipe, di erent run lengths or end system impedance can cause one pipe to handle more CFM than the other. With an accurate CFM reading, piping can be balanced by bleeding air in/out or by creating an extra impedance. DETECT CHANNELG OR PLUGGG For systems in which channeling or plugging can occur, a change in the CFM measured can help indicate the unseen changes in your system. Part/Model Number FM2C3Q FM2C45Q FM2C65Q FM2C125Q FM2C1Q FM2C225Q Specification Units Flow Rate CFM m3/hr Threads B Dimension C Inches mm Dimension D Inches mm Dimension E Inches mm Dimension F Inches mm Part/Model Number FM3C25Q FM3C35Q FM3C4Q FM4C45Q FM4C6Q FM4C85Q Specification Units Flow Rate CFM m3/hr Threads B Dimension C Inches mm Dimension D Inches mm Dimension E Inches mm Dimension F Inches mm USA: Europe: Asia: G 7

162 M A X P R E S S U R E REGENERATIVE BLOWER GROUP MIHELIC II P S I G M A X P R E S SU R E 3... P S AMETEK ROTRON T.I.P. TECHNICAL & DUSTRIAL PRODUCTS MIHELIC II.I G MOISTURE SEPARATOR I S TM REGENERATIVE BLOWER GROUP.. Accessories Measurement - Air Flow Meter TYPICAL FLOW METER ARRANGEMENT 3. ØF M A X P R E S S U R E 3.. P S I G DIA B MIHELIC II 2. FLOW DIRECTION 5.56 C TYPICAL GAUGE FACE M P A T O R O T U R E A R S E SYSTEM PIPG BLOWER LET FLOWMETER SYSTEM UNDER VACUUM HIGH TEMPERATURE/ PRESSURE CORRECTION HOW IT WORKS P1 P2 SCFM 2 = SCFM x ( Pf 2 ) ( Tf ) OUT Pf 2 = Absolute Pressure in PSIA Tf 2 = Temperature in F Use on inlet to limit need to correct for high pressure or elevated outlet temperature Standard model limits = 14 F and 3 PSIG ROTRON S flow meter is a venturi style design. After air enters the inlet, the pressure is measured in the P1 tap. The second tap, P2, measures the pressure at the throat. The differential between P1 and P2 registers across a special calibrated CFM gauge to provide accurate readings. The throat is then expanded back to the original size to keep pressure loss to under 2-4 IWG. USA: Europe: Asia: G 8

163 Accessories Measurement - Digital Flowmeter Remote air flow rate monitoring and system automation control can now be achieved through the use of 4-2 ma output signals. Our 4-2 ma analog outputs are proportional to system flow rates and can be used with PLC controlled operations to monitor system performance. Those same outputs provide digital displays for direct readings in SCFM when paired with our LCD Digital Readout option. Combined with our Variable Frequency Drives, you can now achieve a completely automated system capable of adjusting blower performance to meet changing system demands. Maintaining your system at peak performance gives your company the competitive edge needed in today s marketplace. DIFFERENTIAL PRESSURE TRANSMITTER 4-2 ma signal output control signals provide flow rate monitoring capabilities from remote locations NEMA 1R-raintight enclosure orotects the integrated DC power supply and rugged differential pressure transducer Suitable for remote mounting up to 1' form flow meter Weight: 3 lbs. Signal Output: 4-2 ma, DC 1 Hi/Lo pressure fittings feature snap lock action to unsure trouble-free connections 2 System includes standard flowmeter for on-site readings and troubleshooting Operating temperature: o F to 15 o F Drawing available LCD DIGITAL READOUT OPTIONS Factory configured to display direct readings in SCFM to a remote location up to 5' from signal output 1 NEMA 4, IP65 enclosure ready for panel mount instlation power supply and rugged differential pressure transducer Suitable for remote mounting up to 1' form flow meter installation Power input: 12 VAC, 5/6Hz AC, Field configurable to 24VAC Display: 5 digit, 7 segment,.5" high LED w/3.3hz update rate Operating temperature: 1 o C to 4 o C Weight: 1lb., 14oz COM OUT + EXC 1.87 HIGH LOW Ø.16 (2X) MOUNT HOLES Drawing available Note 1: 4-2 ma output control wiring to be customer supplies. Shielded, 2 conductor cables, 22 AWG is recommemeded for runs up to 1'. For longer runs contact factory 5.51 Note 2: Use 5/16" OD stiff wall tubing-connect "Lo" on flowmeter to "Lo" on 4-2 ma enclosure, "Hi" on flowmeter to "Hi" on 4-2 ma enclosure. Tubing must be equal in length. (Maximum length is 1o feet) DIFFERENTIAL PRESSURE TRANSMITTER FM2S3Q FM2S45Q FM2S65Q FM2S125Q FM2S1Q FM2S225Q FM3S25Q FM3S35Q FM3S4Q FM4S45Q FM4S6Q FM4S85Q LCD DISPLAY FM2L3Q FM2L45Q FM2L65Q FM2L125Q FM2L1Q FM2L225Q FM3L25Q FM3L35Q FM3L4Q FM4L45Q FM4L6Q FM4L85Q USA: Europe: Asia: G 9

164 Accessories Noise Reduction - Sound Attenuating Enclosure Frameless sound attenuating enclosures are a proven way to reduce regeenrative blower mechanical noise when additional mufflers are just not enough. Additional enclosure options are available. FEATURES: Excellent noise reduction (~1DbA) Resistance to elements and aesthetic appearance Compact size for ease of installation Easy access for routine maintenance (removable foor and sidewalls) LIFTG HOLE (PLUGGED) TWO (2) PER SIDE (TOTAL 4) 18" FAN ASSEMBLY SPECIFICATIONS: Roof, floor and walls: galvanized 16 ga. carbon steel sheet metal Louvers and/or hood: Riveted aluminum Hardware: Chrome plated aluminum handles with stainless steel fastners Latches: Over center glvanized with adjustable tension and padlock eye Sound attenuating material: 2" rigid polyester foam with mylar facing (rated UL-94) Exterior finish: Polyurethane enamel Enclosure ventilation: 1/3 HP, 23/46V, 3-phase or 1-phase 5/6Hz fan, TEFC or XP motors Fan Guard: Nickel plated wire type END SECTION END SECTION 31. CLEAR CLEAR Part/Model Number SAE3W72F SAE36W72F Specification Units Width Inches 3 36 mm Blower Size - 656, 77, 7, 88, 858, 99, 979, P9, S9 14, P13, S13, P15, S15 Height Inches mm Length Inches 5 6 mm USA: Europe: Asia: G 1

165 Accessories Noise Reduction - Inlet/Outlet Muffler (Single Connection) B Mufflers lower blower noise in areas where reduced sound levels are required. SPECIFICATIONS: HOUSG Steel MEDIA Acoustical Material D A C Part/Model Number Specification Units Ref Blower Model - B C D E E E Inlet Connection - 1. NPT Male 1.25 NPT Male 1.5 NPT Male 2. NPT Male 2. NPSC Female 2. NPT Male Dimension A Inches mm Dimension B Inches mm Dimension C Inches mm Dimension D Inches mm Blower Model Reference Key A = SPIRAL E = DR/EN/CP 656, 6, 633, S7 B = DR/EN/CP 68, 83, 11, 22 F = DR/EN/CP 7, 88, 858, S9, P9 (Inlet Only) C = DR/EN/CP 33, 312, 313, 353 G = DR/EN/CP 833, S13, P13 (Inlet Only) D = DR/EN/CP 44, 454, 513, 55, 555, 523 H = DR/EN/CP 99, 979, 1233, 14, S15, P15 (Inlet Only) USA: Europe: Asia: G 11

166 Accessories Noise Reduction - Inline Muffler (Dual Connection) Inline Mufflers are utilized for noise reduction in applications where piping systems are connected directly to both ends of the muffler. Muffler may be used on inlet or outlet of blower. C B SPECIFICATIONS: HOUSG Steel MEDIA Acoustical Material LET CONNECTION A OUTLET CONNECTION Part/Model Number Specification Units Ref Blower Model - D E E E F G G G H Inlet Connection NPT-M 2. NPT-M 2. NPSC-F 2. NPT-M 2.5 NPT-M 3. NPT-M 4. NPT-M 4. NPT-M 4. NPT-M Outlet Connection - 2. NPT-F 2. NPSC-F 2. NPSC-F 2. NPT-M 2.5 NPT-F 3. NPT-F 4. NPT-F 4. NPT-M 4. NPT-F Dimension A Inches mm Dimension B Inches mm Dimension C Inches mm Blower Model Reference Key A = SPIRAL E = DR/EN/CP 656, 6, 633, S7 B = DR/EN/CP 68, 83, 11, 22 F = DR/EN/CP 7, 88, 858, S9, P9 (Inlet Only) C = DR/EN/CP 33, 312, 313, 353 G = DR/EN/CP 833, S13, P13 (Inlet Only) D = DR/EN/CP 44, 454, 513, 55, 555, 523 H = DR/EN/CP 99, 979, 1233, 14, S15, P15 (Inlet Only) USA: Europe: Asia: G 12

167 Accessories Protection - Relief Valve - Mechanical Part/ Model Number Specification Units Ref Blower Model - B, C, D D, E, F A, B, C, D, E, F Range in. H2O Connection - 1 1/2 2 2 Description - Mechanical Mechanical Mechanical Vacuum Only Blower Model Reference Key A = SPIRAL E = DR/EN/CP 656, 6, 633, S7 B = DR/EN/CP 68, 83, 11, 22 F = DR/EN/CP 7, 88, 858, S9, P9 (Inlet Only) C = DR/EN/CP 33, 312, 313, 353 G = DR/EN/CP 833, S13, P13 (Inlet Only) D = DR/EN/CP 44, 454, 513, 55, 555, 523 H = DR/EN/CP 99, 979, 1233, 14, S15, P15 (Inlet Only) This document is for informational purposes only and should not be considered as a binding description of the products or their performance in all applications. The performance data on this page depicts typical performance under controlled laboratory conditions. AMETEK is not responsible for blowers driven beyond factory specified speed, temperature, pressure, flow or without proper alignment. Actual performance will vary depending on the operating environment and application. AMETEK products are not designed for and should not be used in medical life support applications. AMETEK reserves the right to revise its products without notification. The above characteristics represent standard products. For product designed to meet specific applications, contact AMETEK Technical & Industrial Products Sales department. G 13 USA: Europe: Asia:

168 Accessories Protection - Pressure Regulating Diaphram Valve The PRD Valve is installed to prevent excessive system pressure or vacuum that could result from line restrictions. Valves should be installed at the blower outlet (downstream) in pressure systems and at blower inlet (upstream) in vacuum systems. These valves are suitable for air, natural gas, propane, and other non-corrosive service. Note: PRD valves are not factory preset, but are easily field adjustable. SPECIFICATIONS: VALVE BODY Aluminum (1"), Cast Iron (2") VALVE SPRG Steel DIAPHRAGM Nitrile GAUGE PORT D Fig. 1 Fig. 2 C DIFFERENTIAL ADJUSTMENT SCREW B D B SEE NOTE A A PRESSURE RELIEF: B is the system port and A is the vent or atmospheric port. VACUUM RELIEF: A is the system port and B is the vent or atmospheric port. For vacuum mode, customer must remove snap ring and screen. NOTE: Replace cap after adjusting setting. Valve will not operate with cap removed. Differential adjustment screw is under the cap. C GAUGE PORT NOTE: Blower Model P13 requires two relief valves. Part/Model Number Specification Units Range in. H2O Description - Fig 1. Fig 1. Fig. 1 Fig. 2 Fig. 2 Fig. 2 Fig. 2 Pressure Vacuum Ref Blower Model - B, C, D, E B, C, D, E B, C, D, E F, G F, G F, G F, G H H Inlet Connection Outlet Connection Dimension A Inches mm Dimension B Inches mm Dimension C Inches mm Dimension D Inches mm Blower Model Reference Key A = SPIRAL E = DR/EN/CP 656, 6, 633, S7 B = DR/EN/CP 68, 83, 11, 22 F = DR/EN/CP 7, 88, 858, S9, P9 (Inlet Only) C = DR/EN/CP 33, 312, 313, 353 G = DR/EN/CP 833, S13, P13 (Inlet Only) D = DR/EN/CP 44, 454, 513, 55, 555, 523 H = DR/EN/CP 99, 979, 1233, 14, S15, P15 (Inlet Only) USA: Europe: Asia: G 14

169 14 16 Accessories Protection - Gauges ROTRON has a variety of gauges for pressure, vacuum and temperature measurements in various ranges. These gauges are reliable and rugged. SPECIFICATIONS: Pressure/ Vacuum CASE Drawn Steel Finished in Black Enamel DIAPHRAGM Bronze LENS Clear Plastic ACCURACY 2%WEIGHT 1/2 lb. CONNECTION 1/4" NPT FACE 2 1/2" dia. Temperature CASE Steel LENS Glass ACCURACY 1% WEIGHT 1/4 lb. CONNECTION 1/2" NPT FACE 3" Dial Pressure 3 2 PRESSURE 1 I 8 P NCHE S S I OF 1 WAT E R Vacuum 3.38 ± Ø 3.18 ± ±.6.25 ± F C 4 2 1/2 NPT CONNECTION Temperature Part/Model Number Specification Units Range - Pressure Pressure Vacuum Vacuum Temperature Description - -6 IWG -16 IWG -6 IWG -16 IWG -2 Deg C USA: Europe: Asia: G 15

170 Accessories System - Variable Frequency Drive A Variable Frequency Drive (VFD) is an adjustable speed AC motor control designed to speed the blower RPM up or down. Our VFDs are designed to minimize losses and deliver increased efficiency, low maintenance, and the long life expected from the ROTRON product line. FEATURES ncy by controlling motor RPMs Accepts 3Ø or 1Ø inputs to drive 3Ø motor blower assemblie saccepts 4-2 ma, -5 VDC or -1 VDC inputs for system automation control and intregation Provides dynamic breaking capabilities Replaces motor starter function Digital readout in either Hz or RPMs Keypad enclosure (NEMA4X-Indoor) vsn be mounted up to 1' from controller with cable assembly option SYSTEM REQUIREMENTS In cases where the distance between the controller and motor exceed 5', the use of a line reactor on load side is needed. XP motors must be UL listteedd for use with a Variable Frequency Drive. VARIABLE FREQUENCY DRIVE SELECTION There are some common guidelines in sizing a VFD for use on a AMETEK ROTRON blowers such as the allowable speed(table 1) for a given motor type. To determine the required RPM to achieve a desired flow and pressure form a specific bloewr, turn to the blower performance at variable speeds in section E of this catalog. The required RPM must fall within the allowable rate of the motor being used. Table 1 Motor Allowable Turndown Allowable Speedup Standard 36 RPM to 18 RPM 36 RPM to 9 RPM Inverter Motor 36 RPM to 36 RPM* 36 RPM to 72 RPM * Turndown of 1:1 is not typically done with regenerative blower designs. For all applications above 36 RPM, contact your Field Sales Engineer for proper horsepower sizing. USA: Europe: Asia: G 16 Specification Model Number Part Number Description IV11AE /1, Up to.5 HP, DR68-DR33 IV12AE /1, Up to.5 HP, DR68-DR33 IV11AL /1,. to 1. HP, DR353-DR44 IV12AL /1 or 3,. to 1. HP, DR353-DR44 IV13AL /3,. to 1. HP, DR353-DR44 IV12AS /1 or 3, 1.5 to 2. HP, DR454-DR55 IV13AS /3, 1.5 to 2 HP DR454-DR55 IV12K /1 or 3, 2.5 to 3 HP, DR55-DR555 IV13K /3, 2.5 to 3. HP, DR55-DR555 23/1 IV12D or 3, 3.5 to 5 HP, DR555-DR88D 46/3, IV13D to 5 HP DR555 to DR88D 23/3, 5.5 IV152AY to 7.5 HP, DR88-DR858 46/3 5.5 to 7.5, IV152AY DR88 DR858 IV152BB /3, 8 to 1 HP, DR858-DR99 IV153BB /3, 8 to 1 HP, DR858-DR99 IV152BC /3, 1.5 to 15 HP, DR99 IV153BC /3, 1.5 to 15 HP, DR99 IV152BH /3, 15.5 to 2 HP, DR9, DR14BH IV153BH /3, 15.5 to 2 HP, DR9, DR14BH IV152BP /3, 2.5 to 3 HP, DR13, DR14 IV153BP /3, 2.5 to 3 HP, DR13, DR14 IV152BQ /3, 3.5 to 4 HP, DR15 IV153BQ /3, 3.5 to 4 HP, DR15 IV153ED /3, 5.5 to 6 HP, DR15

171 Accessories System - Air Knives SGLE-ENDED SIDE VIEW* DOUBLE-ENDED SIDE VIEW** L L 2.5"-8 NPT (TYP) C L C L 2.5"-8 NPT (TYP) C L CL 3.15 TYP. 1.. C L.25-2 UNC X. LG * Air knives 3" and smaller MOUNTG VIEW C L 3.15 TYP. RAIL (REF) 4.58 CAPPED END VIEW GAP SETTG PER MODEL CL 1. S TYP UNC THRU Part/Model Number AK6S6 AK12S6 AK18S6 AK24S6 AK3S6 AK36S6 AK42S6 AK48S6 AK54S6 AK6S6 Specification Units Length (L) Inches mm Slot Length Inches mm Dimension S Inches mm Air Knives An Oil-free Blowing and Drying System Custom-fit for Your Application FEATURES: Lightweight aluminum plenum and rail, steel end cap, and cast-iron NPT flanges Engineered, extruded design to achieve 95% efficiency Adjustable slot (pre-set at.6") to control velocity from 5-35 fpm Custom cut lengths to fit system restraints Oil-free and lower cost alternative to compressed air for blow-off, solution blow-back, and drying applications OPTIONS: TM Chemical resistant designs utilizing Chem-Tough chemically resistant surface conversion, stainless steel hardware, and nickel plated end caps and flanges TM Food processing grade designs utilizing Food-Tough sanitary treatment surface conversion, stainless steel hardware, and nickel plated end caps and flanges Deionizers for sterile environments available Mirror image single-ended models for above and below conveyor operation The ROTRON air knife is located at a strategic point in your assembly line conveyor belt area. Air flows from the blower into the air knife, where a sheet of air is directed out through a proprietary linear nozzle design onto assembly line parts. The opening can be altered to adjust the air-flow rate, thus varying blow-off velocity to meet your application requirements. USA: Europe: Asia: G 17

172 Accessories System - Air Knives Precision Cleaning Air Knife and Blower Selection Chart 6" knife 12" knife 18" knife 24" knife 3" knife 36" knife 42" knife 48" knife 54" knife 6" knife 4, FPM DR88 DR858 DRP9 DRP15 35, FPM DR7 DR99 DR656 3, FPM Air Velocity DRP13 25, FPM DR14 2, FPM DR979 15, FPM SCFM USA: Europe: Asia: G 18

173 Accessories System - 5 Way, 3 Port, 2 Position Diverter Valve SPECIFICATIONS: Aluminum body and spool assembly 33 stainless steel shaft 115 V-6 Hz solenoid valve air OPTIONS Corrosion resistant surface treatments International voltage and frequency (Hz) Application specific designs These unique solenoid actuated diverter valves automatically change air piping from pressure to suction; greatly enhancing blower versatility and productivity. This valve is effective in blower applications that require frequent switching from pressure to suction and vice-versa. They are cost effective as applications normally requiring two blowers and/or intricate piping systems may be accomplished with one blower. Diverter valves may be purchased as blower/valve assemblies, or as separate stand-alone valve assemblies for use in other switched air applications. DR 55 BLOWER WITH DIVERTER VALVE The principle behind ROTRON s diverter valve system is a simple one: Some applications such as vacuum part pick-up, air tables, and pneumatic tube systems require both vacuum and pressure in their equipment s operation, but not simultaneously. They eliminate the need for two sep-arate blowers, and elaborate valving system, or cycling/reversing a spinning blower impeller. ROTRON s diverter valve changes the air passageways. By utilizing the side vent ports for incoming or outgoing air, the equipment/piping side of the valve changes from vacuum to pressure and back again by a signal sent to the solenoid coil. Part/Model Number Specification Units Description - DR44, DR454, DR55 DR6, DR88, DR858 DR6, DR88, DR858 Ref Blower Model - Small Large Large Piping Flange - Threads Threads Threads Blower Flange - Face Threads Face Dimension A Inches mm Dimension B Inches mm Dimension C Inches mm Dimension D Inches mm Dimension E Inches mm Dimension F Inches mm Dimension G Inches mm BLOWER SIDE Blower Blower D C OUT OUT A G E WORKG PART SOLENOID SOLENOID F B EQUIPMENT/PIPG SIDE Consult factory for proper selection and application. SUCTION PRESSURE ISO VALVE DRAWG "PRESSURE" AIR PATH DE-ENERGIZED POSITION "SUCTION" AIR PATH ENERGIZED POSITION USA: Europe: Asia: G 19

174 Accessories System - 5 Way, 3 Port, 2 Position Diverter Valve ROTRON RELEASED BLOWERS WITH DIVERTER VALVE MOUNTED Model * Part No. Mounted Components Diverter Valve Manifold DR353BR58MV 87 DR44AL72MV DR44AL58MV DR454R72V DR454R58V DR55AS72MV 3779 DR55AS58MV DR88AY72WV 884 DR858BB72WV DIVERTER VALVE MANIFOLD Models listed below include diverter valve and manifold. Blower Model Reference Key A = SPIRAL E = DR/EN/CP 656, 6, 633, S7 B = DR/EN/CP 68, 83, 11, 22 F = DR/EN/CP 7, 88, 858, S9, P9 (Inlet Only) C = DR/EN/CP 33, 312, 313, 353 G = DR/EN/CP 833, S13, P13 (Inlet Only) D = DR/EN/CP 44, 454, 513, 55, 555, 523 H = DR/EN/CP 99, 979, 1233, 14, S15, P15 (Inlet Only) USA: Europe: Asia: G 2