PRECISE. Glove Boxes

Transcription

1 PRECISE Glove Boxes

2 PRECISE Basic Glove Boxes All models feature: One-piece molded, medium-density polyethylene shell. Dry powder epoxy-coated steel superstructure. 1/4" thick laminated safety glass viewing window with powder-coated steel frame and neoprene gasket. Cutout is 26.4" w x 12.5" high. Window is easily removable for loading equipment. Space-saving inner and outer transfer chamber doors that pivot upward, are counterbalanced and equipped with quicklatches. Black, chemical-resistant phenolic core work surface sealed to the glove box floor. Interior ceiling-mounted electrical duplex receptacle with 5 amp maximum (100/115 volt models) or 2 amp maximum (230 volt models) circuit load. Pair of neoprene gloves, 0.15" thick, 30" long, size 9 3/4. Fluorescent lamp, 22 watts, with easy replacement from the top. Switches for light and innermost interior electrical receptacle. Precise Basic Glove Boxes are designed to provide a leak-tight physical barrier between the user and the materials inside the glove box. These simple, economical boxes are designed to allow the user to customize them with accessories to meet specific applications. Precise Basic Glove Box on Mobile Stand Approximately 13 cubic feet of interior space in main chamber, 33.5" w x 27.5" d maximum x 25.0" high, (85 x 70 x 64 cm). 11.0" nominal ID x 12.0" long transfer chamber. Factory leak tested with a mass spectrometer while glove box is pressurized with helium at 5 inches of water gauge. No detectable leaks greater than 1 x 10-4 ml/sec. Meet Class 1 atmosphere containment conditions for oxygen leak rates per ISO test method. Transfer chamber interior interlocking shelf of dry powder epoxy-coated steel. ETL listing, UL / and CAN/CSA C22.2 No conformity (100 and 115 volt models) CE Conformity Marking (230 volt models) Overall dimensions 52.7" w x 31.6" d x 40.0" high (134 x 80 x 102 cm). Shipping weight 255 lbs. (116 kg). All models require: Supporting base. See page 6 for Adjustable Height Base Stands or Work Surface and Protector Standard Base Cabinet. Ordering Information Catalog Electrical Number Configuration volts, 60 Hz, 8 amps * 230 volts, 50 Hz, 4 amps volts, 60 Hz, 4 amps * 100 volts, 50 Hz, 8 amps * 100 volts, 60 Hz, 8 amps Accessories include: See pages 6 and 7 for ordering information on these and additional accessories. Add-A-Valve Kit. Complete Valve Set. Pressure Relief Valve. Main Chamber Pressure Gauge. Transfer Chamber Pressure Gauge. Transfer Chamber High Vacuum Sleeve. Automatic Pressure Controllers for automatic purging/filling up to 199 cycles, automatic pressure regulation between - 5 to +5 inches of water gauge in the main glove box and 0 to -29 inches of mercury in the transfer chamber. Gas Fill/Vacuum Purge Tubing Kits that provide the necessary tubing to connect to an inert gas and a vacuum pump. Remote Blowers for pressure relief valve exhaust. Pressure Relief Valve Vent Kits for ducting to the outside or into the room. Drying Train components for removing oxygen, moisture, solvents and other vapors, which include Oxygen and Moisture Removal Column, Diaphragm Pumps, Traps, Stands and Flowmeter. Oxygen and Moisture Monitors. External Glove Port Covers. 2 Exclusive feature

3 PRECISE Controlled Atmosphere Glove Boxes All models feature: One-piece molded, medium-density polyethylene shell. Dry powder epoxy-coated steel superstructure. 1/4" thick laminated safety glass viewing window with powder-coated steel frame and neoprene gasket. Cutout is 26.4" w x 12.5" high. Window is easily removable for loading equipment. Space-saving inner and outer transfer chamber doors that pivot upward, are counterbalanced and equipped with quicklatches. Black, chemical-resistant phenolic core work surface sealed to the glove box floor. Pressure relief valve that activates at pressure/vacuum above 6 inches or below -6 inches of water gauge. Pressure relief valve vent, 4" nominal diameter. See page 7 for optional Filtered Pressure Relief Valve Vent Kits for outside or filtered room exhaust. Interior ceiling-mounted electrical duplex receptacle with 5 amp maximum (100/115 volt models) or 2 amp maximum (230 volt models) circuit load. Pair of neoprene gloves, 0.15" thick, 30" long, size 9 3/4. Fluorescent lamp, 22 watts, with easy replacement from the top. Precise Controlled Atmosphere Glove Boxes provide a leak-tight environment for work with contamination-sensitive materials. Procedures where low levels of oxygen, as low as 5 ppm, or moisture, as low as 50 ppm, are important, such as work with organometallics, alternative energy cells or hydrophilic chemicals, are typical applications for these glove boxes. Precise Controlled Atmosphere Glove Box on Mobile Stand Switches for light and innermost interior electrical receptacle. Approximately 13 cubic feet of interior space in main chamber, 33.5" w x 27.5" d maximum x 25.0" high, (85 x 70 x 64 cm). 11.0" nominal ID x 12.0" long transfer chamber. Factory leak tested with a mass spectrometer while glove box is pressurized with helium at 5 inches of water gauge. No detectable leaks greater than 1 x 10-4 ml/sec. Performance tested to maintain less than 5 ppm oxygen levels and less than 50 ppm moisture levels. Meet Class 1 atmosphere containment conditions for oxygen leak rates per ISO test method. Six manual valves with 3/8" compression fittings and 3/8" hose barbs. Two on the main chamber and two on the transfer chamber are for purging and filling. The other two on the main chamber are for drying train connections. For additional valves, see Add-A-Valve Kit, on page 6. Main chamber pressure gauge with readings from -5 to +5 inches of water gauge. Transfer chamber pressure gauge with readings from 0 to -29 inches of mercury. Transfer chamber high vacuum sleeve and interior interlocking shelf of dry powder epoxy-coated steel. ETL listing, UL / and CAN/CSA C22.2 No conformity (100 and 115 volt models) CE Conformity Marking (230 volt models) Overall dimensions 52.7" w x 31.6" d x 40.0" high (134 x 80 x 102 cm). Shipping weight 260 lbs. (118 kg). All models require: Supporting base. See page 6 for Adjustable Height Base Stands or Work Surface and Protector Standard Base Cabinet. Vacuum source for purging. See page 7 for Direct Drive Vacuum Pumps. Inert gas for filling. Contact your laboratory supply distributor. Ordering Information Catalog Electrical Number Configuration volts, 60 Hz, 8 amps * 230 volts, 50 Hz, 4 amps volts, 60 Hz, 4 amps * 100 volts, 50 Hz, 8 amps * 100 volts, 60 Hz, 8 amps Accessories include: See pages 6 and 7 for ordering information on these and additional accessories. Automatic Pressure Controllers for automatic purging/filling up to 199 cycles, automatic pressure regulation between -5 to +5 inches of water gauge in the main chamber and 0 to -29 inches of mercury in the transfer chamber. Gas Fill/Vacuum Purge Tubing Kits that provide the necessary tubing to connect to inert gas and vacuum pump. Remote Blowers for pressure relief valve exhaust. Pressure Relief Valve Vent Kits for ducting to the outside or into the room. Drying Train components for removing oxygen, moisture, solvents and other vapors, which include Oxygen and Moisture Removal Column, Diaphragm Pumps, Traps, Stands and Flowmeter. Oxygen and Moisture Monitors. External Glove Port Covers. Exclusive feature 3

4 PRECISE HEPA-Filtered Glove Boxes All models feature: One-piece molded, medium-density polyethylene shell. Dry powder epoxy-coated steel superstructure. 1/4" thick laminated safety glass viewing window with powder-coated steel frame and neoprene gasket. Cutout is 26.4" w x 12.5" high. Window is easily removable for loading equipment. Space-saving inner and outer transfer chamber doors that pivot upward, are counterbalanced and equipped with quick-latches. Black, chemical-resistant phenolic core work surface sealed to the glove box floor. Interior ceiling-mounted electrical duplex receptacle with 5 amp maximum (100/115 volt models) or 2 amp maximum (230 volt models) circuit load. Pair of neoprene gloves, 0.15" thick, 30" long, size 9 3/4. Built-in blower with speed control capable of airflow from 13 CFM to 100 CFM. Fluorescent lamp, 22 watts, with easy replacement from the top. Precise HEPA-Filtered Glove Boxes have inlet and outlet HEPA filters and provide a leak-tight physical barrier to protect the operator from hazardous airborne particulates and powders. These boxes have uses in pharmaceutical research, nanotechnology and biochemistry. Microorganisms, low-level radiochemicals, chemical carcinogens and asbestos may also be used in these boxes. These boxes may be used for cleanroom applications requiring ISO Class 3 (ISO ) conditions. Precise HEPA-Filtered Glove Box on Mobile Stand Switches for light, blower and innermost interior electrical receptacle. Inlet and outlet HEPA filters, 99.99% efficient on 0.3 micron particulates, and test port for challenging HEPA filter integrity. Main chamber static pressure gauge for monitoring HEPA filter loading. Approximately 13 cubic feet of interior space in main chamber, 33.5" w x 27.5" d maximum x 25.0" high, (85 x 70 x 64 cm). 11.0" nominal ID x 12.0" long transfer chamber. Transfer chamber interior interlocking shelf of dry-powder epoxy-coated steel ppm average tracer gas levels or less detected during perimeter scan testing (surpasses ASHRAE 110 standards). Airborne particulate cleanliness (measured under positive and negative pressures per ISO test method) exceeds ISO Class 5 conditions (equivalent to Class 100) and achieved ISO Class 3 conditions (equivalent to Class 1) at both minimum and maximum operational airflow volumes. Vibration less than 1.5 x 10-5 inches displacement measured at the work surface at both minimum and maximum airflow volumes. Factory leak tested with a mass spectrometer while pressurized with helium at 1 inch of water gauge. No detectable leaks greater than 1 x 10-3 ml/sec. ETL listing, UL / and CAN/CSA C22.2 No conformity (100 and 115 volt models). CE Conformity Marking (230 volt models). Overall dimensions 52.7" w x 31.6" d x 40.0" high (134 x 80 x 102 cm). Shipping weight 280 lbs. (127 kg). All models require: Supporting base. See page 6 for Adjustable Height Base Stands or Work Surface and Protector Standard Base Cabinet. Ordering Information Catalog Electrical Number Configuration volts, 60 Hz, 8 amps * 230 volts, 50 Hz, 4 amps volts, 60 Hz, 4 amps * 100 volts, 50 Hz, 8 amps * 100 volts, 60 Hz, 8 amps Accessories include: See pages 6, 7 and back cover for ordering information on these and additional accessories. Positive Pressure Conversion Kit to change negative pressure operation inside the glove box to positive pressure. Recirculation Kit to allow the blower exhaust to be connected to the inlet HEPA filter for recirculation of the exhaust air, useful for dry atmosphere operations. Blower Foot Switch. Anti-Static Ionizer Fan to reduce static charge during applications involving weighing. Blower Speed Control Dial Setting Min. Dial 20 Dial 40 Dial 50 Dial 60 Dial 80 Dial Max. Dial Air Volume Changes Per Minute Exhaust Volume (CFM) Noise Pressure db(a) Static Pressure in Glove Box (in. of H 2 O) Total System Static Pressure (in. of H 2 O) Exclusive feature

5 XPERT Weigh Boxes All models feature: One-piece molded, medium-density polyethylene shell. Dry powder epoxy-coated steel superstructure. 1/4" thick laminated safety glass viewing window with powder-coated steel frame and neoprene gasket. Cutout is 26.4" w x 12.5" high. Window is removable for loading equipment. Space-saving inner and outer transfer chamber doors that pivot upward, are counterbalanced and equipped with quick-latches. Black, chemical-resistant phenolic core work surface sealed to the glove box floor. Interior ceiling-mounted electrical duplex receptacle with 5 amp maximum (100/115 volt models) or 2 amp maximum (230 volt models) circuit load. Pair of neoprene gloves, 0.15" thick, 30" long, size 9 3/4. Built-in blower with speed control capable of airflow from 13 CFM to 100 CFM. Fluorescent lamp, 22 watts, with easy replacement from the top. XPert Weigh Boxes have inlet and outlet HEPA filters and provide a leak-tight physical barrier to protect the operator from hazardous airborne particulates and powders. These boxes include an anti-static ionizer fan to reduce static charge and a balance vibration isolator, both useful during weighing operations. XPert Weigh Box on Stationary Stand Switches for light, blower and innermost interior electrical receptacle wired for ionizer fan. Inlet and outlet HEPA filters, 99.99% efficient on 0.3 micron particulates, and test port for challenging HEPA filter integrity. Main chamber static pressure gauge for monitoring HEPA filter loading. Anti-static ionizer fan, mounted on the interior ceiling, to circulate ionized air inside the box to reduce static charge during weighing. Balance vibration isolator, consisting of a 13.4" w x 20.4" d x 2.7" thick (34 x 52 x 7 cm) marble slab with isolator pads and type 304 stainless steel cover. Approximately 13 cubic feet of interior space in main chamber, 33.5" w x 27.5" d maximum x 25.0" high, (85 x 70 x 64 cm). 11.0" nominal ID x 12.0" long transfer chamber. Transfer chamber interior interlocking shelf of dry-powder epoxy-coated steel ppm average tracer gas levels or less detected during perimeter scan testing (surpasses ASHRAE 110 standards). Airborne particulate cleanliness (measured under positive and negative pressures per ISO test method) exceeds ISO Class 5 conditions (equivalent to Class 100) and achieved ISO Class 3 conditions (equivalent to Class 1) at both minimum and maximum operational airflow volumes. Vibration less than 1.5 x 10-5 inches displacement measured at the work surface at both minimum and maximum airflow volumes. Factory leak tested with a mass spectrometer while pressurized with helium at 1 inch of water gauge. No detectable leaks greater than 1 x 10-3 ml/sec. ETL listing, UL / and CAN/CSA C22.2 No conformity (100 and 115 volt models). CE Conformity Marking (230 volt models). Overall dimensions 52.7" w x 31.6" d x 40.0" high (134 x 80 x 102 cm). Shipping weight 350 lbs. (159 kg). All models require: Supporting base. See page 6 for Adjustable Height Base Stands or Work Surface and Protector Standard Base Cabinet. Ordering Information Catalog Electrical Number Configuration volts, 60 Hz, 8 amps * 230 volts, 50 Hz, 4 amps volts, 60 Hz, 4 amps * 100 volts, 50 Hz, 8 amps * 100 volts, 60 Hz, 8 amps Accessories include: See pages 6, 7 and back cover for ordering information on these and additional accessories. Positive Pressure Conversion Kit to change negative pressure operation inside the glove box to positive pressure. Recirculation Kit to allow the blower exhaust to be connected to the inlet HEPA filter for recirculation of the exhaust air, useful for dry atmosphere operations. Blower Foot Switch. Blower Speed Control Dial Setting Min. Dial 20 Dial 40 Dial 50 Dial 60 Dial 80 Dial Max. Dial Air Volume Changes Per Minute Exhaust Volume (CFM) Noise Pressure db(a) Static Pressure in Glove Box (in. of H 2 O) Total System Static Pressure (in. of H 2 O) Exclusive feature 5

6 Catalog Number Description Precise Glove Boxes General Accessories Adjustable Height Mobile Base Stand with permanently-mounted black laminate work surface and casters. Includes a lower shelf to support accessory equipment. 60.0" w x 31.0" d x 33.0" to 40.0" high Adjustable Height Stationary Base Stand with permanently-mounted black laminate work surface and leveling feet. Includes a lower shelf to support accessory equipment. 60.0" w x 31.0" d x 33.0" to 40.0" high Black Epoxy Flat Work Surface, solid epoxy resin, 60.0" w x 30.0" d x 1.25" thick Protector Standard Base Cabinet, 30.0" w x 22.0" d x 35.5" to 36.75" high. Glacier white epoxy-coated steel. Includes two non-locking, manual-closing doors; four leveling feet; and one 8" filler panel to increase cabinet depth from 22" to 30". Two cabinets are required to support the glove box. Requires Black Epoxy Flat Work Surface Add-a-Valve Kit, includes the manual valve, O-ring and nut to add a service valve to the main glove box or transfer chamber. Requires installation and 0.688" dia. hole. Precise Controlled Atmosphere Glove Boxes include six manual valves Valve Identifier Label Set, includes labels for two VAC, two GAS, IN, OUT, AR, NIT, AIR, CO 2 and CW. For use when adding service valve(s) External Glove Port Covers, with clamps, for use in purge/fill operation and to preserve inert atmosphere. Set of two Remote Blower, for 115 volt, 60 Hz, 4.4 amp operation, provides 167 CFM at 0.87" static pressure. 1/4 hp direct drive motor, epoxy-coated steel housing and wheel, 6.00" ID inlet and 4.25" x 7.38" OD outlet. For use with Precise Controlled Atmosphere Glove Boxes for pressure relief valve vent exhausting to the outside or on Precise HEPA-Filtered Glove Boxes and XPert Weigh Boxes for exhausting to the outside * Remote Blower, for 115/230 volt, 50 Hz, 4.4 amp operation, provides 167 CFM at 0.87" static pressure. 1/4 hp direct drive motor, epoxy-coated steel housing and wheel, 6.00" ID inlet and 4.25" x 7.38" OD outlet. For use with Precise Controlled Atmosphere Glove Boxes for pressure relief valve vent exhausting to the outside or on Precise HEPA-Filtered Glove Boxes and XPert Weigh Boxes for exhausting to the outside Guardian Jr. Airflow Monitor, for 100/115/230 volt, 50/60 Hz operation, for monitoring airflow from the pressure relief valve vent on Precise Controlled Atmosphere Glove Boxes or monitoring exhaust airflow on Precise HEPA-Filtered Glove Boxes and XPert Weigh Boxes. Mounts to top of the glove box Vacuum Aspirator Kit, for 115 volt operation, includes the valve, hose, canister and diaphragm vacuum pump for evacuating fluids around the interior work surface * Vacuum Aspirator Kit, for 230 volt operation, includes the valve, hose, canister and diaphragm vacuum pump for evacuating fluids around the interior work surface Electrical Power Strip, 4 receptacles, for 115 volt, 5 amp operation, may be plugged into the interior receptacle * United Kingdom Electrical Power Strip, 6 receptacles, for 250 volt, 2 amp operation, may be plugged into the interior receptacle * European Electrical Power Strip, 4 receptacles, for 250 volt, 2 amp operation, may be plugged into the interior receptacle * Australian Electrical Power Strip, 6 receptacles, for 250 volt, 2 amp operation, may be plugged into the interior receptacle Power Strip Installation Tool, which aids connection to the interior receptacle without removing the viewing window Electrical 9 Pin Sealed Pass-Through Kit, includes sealed 9 pin connector (D-subminiature with male pins on one side and female pins on the other) and cord for connecting electrical equipment, such as a balance, inside the glove box to electrical equipment, such as a printer, outside the glove box. Requires installation. Installation Kit , with drill bits and hole saws, is recommended Acrylic Viewing Window, 1/2" thick, with dry powder epoxy-coated steel frame, to replace standard laminated glass window Rear Interior Storage Shelf Kit, with four stainless steel shelves, two are 21.2" w x 3.2" d, and two are 21.2" w x 3.5" d. Requires assembly Left-Side Interior Storage Shelf Kit, with four stainless steel shelves, each is 21.2" w x 3.5" d. Requires assembly IV Bar Kit. Requires or Storage Shelf Kit Hanging Utility Shelves, consist of three epoxy-coated steel shelves for miscellaneous supplies. Requires Storage Shelf Kit Hanging Bottle Holder, epoxy-coated steel with 3" diameter opening for holding squirt bottle. Requires Storage Shelf Kit Hanging Tissue Holder, epoxy-coated steel to hold box of wipes. Requires Storage Shelf Kit Hanging Bin Organizer, plastic, 5.4". Requires Storage Shelf Kit Hanging Bin Organizer, plastic, 7.4". Requires Storage Shelf Kit Exterior Transfer Chamber Shelf, 10.7" wide x 15.1" deep, dry powder epoxy-coated steel, mounts to top of transfer chamber to maximize exterior work area Anti-Static Ionizer Fan, for 100/115 volt, 50/60 Hz operation, for circulating ionized air inside the glove box to reduce static charge. Includes hardware to mount to the interior ceiling. Requires installation. Included with 100/115 volt XPert Weigh Boxes Anti-Static Ionizer Fan, for 230 volt, 50/60 Hz operation, for circulating ionized air inside the glove box to reduce static charge. Includes hardware to mount to the interior ceiling. Requires installation. Included with 230 volt XPert Weigh Boxes Balance Vibration Isolator, minimizes vibration to sensitive balances. Includes a 13.4" w x 20.4" d x 2.7" thick marble slab, four isolator pads, and a type 304 stainless steel protective top cover. Included with XPert Weigh Boxes Neoprene Gloves, size 8 1/2, one piece, seamless, gauge, with O-rings. One pair Neoprene Gloves, size 9 3/4, one piece, seamless, gauge, with O-rings. One pair. Included with Precise Glove Boxes Butyl Gloves, size 8 1/2, one piece, seamless, gauge, with O-rings. Provide high dexterity and impermeability to water vapor, gases and toxic chemicals. Resistant to oxygenated solvents and most oxidizing chemicals. One pair Butyl Gloves, size 9 3/4, one piece, seamless, gauge, with O-rings. Provide high dexterity and impermeability to water vapor, gases and toxic chemicals. Resistant to oxygenated solvents and most oxidizing chemicals. One pair Hypalon Gloves, size 8 1/2, one piece, seamless, gauge, with O-rings. Resistant to abrasion, ozone and oxidizing chemicals. One pair Hypalon Gloves, size 9 3/4, one piece, seamless, gauge, with O-rings. Resistant to abrasion, ozone and oxidizing chemicals. One pair. 6

7 Catalog Number Description Precise Glove Boxes Drying Train Accessories Diaphragm Pump, for 115 volt, 60 Hz operation, for drying train circulation, with switch * Diaphragm Pump, for 230 volt, 50 Hz operation, for drying train circulation Canister with Stand for holding trap insert (Trap Inserts sold separately. See below.) Moisture & Solvent Trap Insert, contains molecular sieve to achieve less than 50 ppm moisture (when used with the Precise Controlled Atmosphere or Basic Glove Boxes) Acid Trap Insert, contains acid neutralizing desiccant that changes from off white to purple when exhausted Radioisotope Trap Insert, contains activated carbon Ammonia Trap Insert, contains impregnated carbon Flowmeter, for inline drying train connection to provide visual confirmation of drying train circulation Moisture Drying Train Tubing Kit, includes tubing and fittings for connection to , , or Trap Insert (sold separately) Gas and Vacuum 0.2 Micron Filter, for drying train or vacuum pump exhaust, traps particulates, " ID. Catalog Number Description Precise Controlled Atmosphere and Basic Glove Boxes Additional Accessories Direct Drive Rotary Vane Vacuum Pump, for 115 volt, 50/60 Hz, 4.6 amp operation, with NEMA 5-15P plug, 117 liters/minute displacement (at 60 Hz), for purging main chamber and transfer chamber Direct Drive Rotary Vane Vacuum Pump, for 230 volt, 50/60 Hz, 2.4 amp operation, with NEMA 6-15P plug, 117 liters/minute displacement (at 60 Hz), for purging main chamber and transfer chamber * Direct Drive Rotary Vane Vacuum Pump, for 230 volt, 50/60 Hz, 2.4 amp operation, with reverse IEC plug, 117 liters/minute displacement (at 60 Hz), for purging main chamber and transfer chamber Automatic Pressure Controller, for 115 or 100 volt operation, for up to 199 automatic purging/filling cycles in the main chamber and transfer chamber. Automatically regulates vacuum/pressure between -5 and +5 inches of water gauge in the main chamber and 0 and -29 inches of mercury in the transfer chamber * Automatic Pressure Controller, for 230 volt operation, for up to 199 automatic purging/filling cycles in the main chamber and transfer chamber. Automatically regulates vacuum/pressure between -5 and +5 inches of water gauge in the main chamber and 0 and -29 inches of mercury in the transfer chamber Manual Valve Gas and Vacuum Tubing Connection Kit, includes tubing to connect inert gas and rotary vane vacuum pump to manual valves Automatic Pressure Controller Gas and Vacuum Tubing Connection Kit, includes tubing to connect inert gas and rotary vane vacuum pump to or Automatic Pressure Controller (sold separately) Oxygen and Moisture Removal Column, to provide less than 5 ppm oxygen and less than 50 ppm moisture (refillable) Oxygen and Moisture Removal Column Support Stand, for holding Oxygen and Moisture Removal Column Oxygen and Moisture Drying Train Tubing Kit, includes tubing and fittings for connection to Oxygen and Moisture Removal Column (sold separately) Pressure Relief Valve, activates at pressure/vacuum above 6 inches of water gauge and below -6 inches water gauge. Included with Precise Controlled Atmosphere Glove Boxes and Complete Valve Kit. Requires installation Pressure Relief Valve Vent Kit, includes 3.9" OD x 3.8" ID thimble connection for ducting to the outside. Requires Pressure Relief Valve (included with Precise Controlled Atmosphere Glove Boxes) HEPA-Filtered Pressure Relief Vent Kit, includes 3.9" OD x 3.8" ID thimble connection and 99.99% efficient HEPA filter for ducting to the outside or the room. May be used with Vent Kit. Requires Pressure Relief Valve (included with Precise Controlled Atmosphere Glove Boxes) Carbon-Filtered Pressure Relief Vent Kit, includes 3.9" OD x 3.8" ID thimble connection and activated carbon filter for ducting to the outside or the room. May be used with Vent Kit. Requires Pressure Relief Valve (included with Precise Controlled Atmosphere Glove Boxes) Oxygen Monitor, for 115 or 100 volt operation, 0-10,000 ppm (with three ranges of ppm, ppm, and ,000 ppm) Oxygen Monitor, for 230 volt operation, 0-10,000 ppm (with three ranges of ppm, ppm, and ,000 ppm) Oxygen Monitor, for 100/115/230 volt operation, % Oxygen Monitor (1000 ppm lowest) Moisture Monitor/Hygrometer, for 115 or 100 volt operation, ppm (with three ranges of 1-10 ppm, ppm, and ppm) Moisture Monitor/Hygrometer, for 230 volt operation, ppm (with three ranges of 1-10 ppm, ppm, and ppm) Hand-held Digital Hygrometer, 0-100%, with temperature display, to measure humidity and temperature Complete Valve Kit, includes six manual valves, mounting brackets, pressure relief valve and labels. Requires installation and 0.688" diameter hole for each valve. Six valves are included with Precise Controlled Atmosphere Glove Boxes Main Chamber Pressure Gauge Kit, monitors pressures between -5 and +5 inches of water gauge. Includes pressure gauge, hose and fittings. Requires installation and 0.562" diameter hole. Included with Precise Controlled Atmosphere Glove Boxes Transfer Chamber Pressure Gauge Kit, monitors pressure/vacuum from 0 to -29 inches of mercury. Includes vacuum gauge, hose, mounting bracket and fittings. Requires installation. Included with Precise Controlled Atmosphere Glove Boxes Transfer Chamber High Vacuum Sleeve, epoxy-coated steel, mounts in the interior of the transfer chamber. Required when purging the transfer chamber. Included with Precise Controlled Atmosphere Glove Boxes. 7

8 Precise HEPA-Filtered Glove Boxes and XPert Weigh Boxes Additional Accessories Catalog Number Description Blower Foot Switch, provides a hands-free means to shut off power to the built-in blower DOP Test Kit for HEPA Filters, includes the connections and hoses necessary to conduct the HEPA filter leak test Replacement Inlet or Outlet HEPA Filter, 99.99% efficient on 0.3 micron particles ULPA Filter, % efficient on 0.3 micron particles. May be used in place of the standard inlet or outlet HEPA filter Bag Set for Bag-in/Bag-out HEPA Filter Replacement. Includes two bags and two straps necessary for one filter replacement Positive Pressure Conversion Kit, for converting the built-in blower from negative pressure to positive pressure operation Transfer Chamber Pressure Gauge Kit, monitors pressure/vacuum from 0 to -29 inches of mercury. Includes vacuum gauge, hose, mounting bracket and fittings. Mounts to top of glove box. Requires installation Remote Wall-Mount Blower Kit, includes mounting hardware to place the built-in blower on a wall up to five feet away Waste Chute, provides a 4.5" diameter pass-through port to attach an external waste bag. Minimum waste bag size: 8.5" wide. Waste bags and bands are required (contact your laboratory supply dealer) Recirculation Kit, to allow the built-in blower exhaust to be connected to the inlet HEPA filter for recirculation of air, useful for dry atmosphere operations Mechanical or Electrical Straight Pass-Through Kit, provides three pass-through ports with ID sizes of 0.230/0.395, 0.230/0.530 and 0.450/0.705, useful for sealing cords and plumbing. Requires installation. Installation Kit , with drill bits, is recommended FilterMate Portable Exhauster, for 115 volt, 60 Hz operation, with 99.99% efficient HEPA filter * FilterMate Portable Exhauster, for 230 volt, 50 Hz operation, with 99.99% efficient HEPA filter FilterMate Portable Exhauster, for 115 volt, 60 Hz operation, for use with Carbon Filter (Carbon Filter sold separately) * FilterMate Portable Exhauster, for 230 volt, 50 Hz operation, for use with Carbon Filter (Carbon Filter sold separately) FilterMate Portable Exhauster, for 115 volt, 60 Hz operation, with 99.99% efficient HEPA filter, with 6.06" ID thimble for outside ducting * FilterMate Portable Exhauster, for 230 volt, 50 Hz operation, with 99.99% efficient HEPA filter, with 6.06" ID thimble for outside ducting FilterMate Portable Exhauster, for 115 volt, 60 Hz operation, with 99.99% efficient HEPA filter and for use with Carbon Filter (Carbon Filter sold separately) * FilterMate Portable Exhauster, for 230 volt, 50 Hz operation, with 99.99% efficient HEPA filter and for use with Carbon Filter (Carbon Filter sold separately) FilterMate Portable Exhauster, for 115 volt, 60 Hz operation, for use with two Carbon Filters (Carbon Filters sold separately) * FilterMate Portable Exhauster, for 230 volt, 50 Hz operation, for use with two Carbon Filters (Carbon Filters sold separately) Replacement HEPA Filter, 99.99% efficient, for FilterMate Portable Exhauster Replacement Bag for Bag-In/Bag-Out HEPA Filter, for FilterMate Portable Exhauster Organic Carbon Filter, Type AC, for FilterMate Portable Exhauster. Contains 12 pounds of granular activated carbon media Formaldehyde Carbon Filter, Type CI, for FilterMate Portable Exhauster. Contains 14 pounds of impregnated carbon media Ammonia Carbon Filter, Type CX, for FilterMate Portable Exhauster. Contains 16 pounds of impregnated carbon media Thimble Exhaust Connector, 5" diameter, for connecting the glove box to the FilterMate Portable Exhauster Thimble Exhaust Connector, 6" diameter, for connecting the glove box to building exhaust or remote blower for outside ducting Hard Duct Exhaust Connector, 6" diameter, for connecting the glove box to a remote blower, when by-passing the glove box s blower. Contact Labconco for ordering information on additional accessories including Exhaust Dampers and other ductwork. XPert Weigh Boxes include the Anti-Static Ionizer Fan. The Anti-Static Ionizer Fan or may be added as an accessory to any Precise Glove Box. XPert Weigh Boxes include the Balance Vibration Isolator. The Balance Vibration Isolator may be added as an accessory to any Precise Glove Box. LABCONCO CORPORATION 8811 Prospect Avenue Kansas City, MO or FAX labconco@labconco.com 2007 by Labconco Corporation. Printed in the U.S.A. Product design subject to change without notice /07-James-3M-R1