11812 NE 116th Street TEL: Kirkland, WA USA FAX: TECHNICAL DATA SHEET AMFLOW AM9A FLOW CONTROL VALVE

Transcription

1 A & H Enterprises, Inc. Amflow NE 116th Street TEL: Kirkland, WA USA FAX: ah@amflow.com TECHNICAL DATA SHEET AMFLOW AM9A FLOW CONTROL VALVE Part Number: (*Reference Order Guide) Certifications and Patents: Certification of material type and condition, and all post processes, including anodizing, heat treatment, plating, and all chemical processes, will be maintained on file with A & H Enterprises, Inc. for a period not less than five years. ATEX II 2G EEx c T3 US PATENTS 5,427,139 * 5,494,070 * 6,189,564,B1 EU PATENT A & H Enterprises, Inc. reserves the right to amend and change specifications without prior notice US PATENTS: 5,427,139 * 5,494,070 * 6,189,564,B1 * EU PATENT * Rev. C, 04/16 Page 1 of 7

2 AM9AData Sheet GA DRAWING GA DRAWING: Port Jet Access Port Inlet Port Location (3/4 tube stub shown) Outlet Port Location (3/4 tube stub shown) Inlet and Outlet ports are Medium Pressure SF750 CX US PATENTS: 5,427,139 * 5,494,070 * 6,189,564,B1 * EU PATENT * Rev. C, 04/16 Page 2 of 7

3 FEATURES & OPTIONS Features Purge Port: Incorporated into the Amflow AM9A Valve is a purge port that allows the user to direct a high flow stream of chemical across the fixed orifice in order to flush any chemical residue that might accumulate over time. This feature reduces the necessity of opening the valve and cleaning the jet manually. The Purge port is located 180 degrees from the Inlet Port. Panel Mount Dimensions Actuated Options AM9A Shown with Amflow A6 Actuator US PATENTS: 5,427,139 * 5,494,070 * 6,189,564,B1 * EU PATENT * Rev. C, 04/16 Page 3 of 7

4 SPECIFICATIONS 1. FLOW RATES 1.01 Flow * MINIMUM: 120 LPH MAXIMUM: 1200 LPH 1.01a Flow Rate with Methanol ** 1370 LPH 1.02 Operating Pressure - Duplex 2205*** MINIMUM: 20 bar (300 PSI) MAXIMUM: 827 bar (11,995 PSI) 1.02a Operating Pressure - Super Duplex 2507*** MINIMUM: 20 bar (300 PSI) MAXIMUM: 827 bar (11,995 PSI) 1.02b Operating Pressure 17-4 PH SS*** MINIMUM: 20 bar (300 PSI) MAXIMUM: 920 bar (13,340 PSI) 1.02c Operating Pressure Titanium*** MINIMUM: 20 bar (300 PSI) MAXIMUM: 920 bar (13,340 PSI) 1.03 Hydrostatic Pressure Test 1241 bar (17,995 PSI) 1380 bar (20,010 PSI) 1.04 Pressure Drop **** STANDARD: 7 bar p MAXIMUM: 10 bar p 1.04 Operating Temperature MINIMUM: -15 C ( 5 F) MAXIMUM: 200 C (392 F) 2. TURNDOWN RATIO ***** UP TO - 10:1 3. ACCURACY & REPEATABILITY + 3% full range of flow 4. PORT CONFIGURATION Standard Inlet/Outlet Ports Standard Purge Ports 4.01 Positioned as shown on picture SF 750CX SF 250CX 5. NOISE Decibels 5.01 Less Than 70 db 6. CONSTRUCTION MATERIALS Standard Material Special Order 6.01 Body 17-4 PH SS Contact Manufacturer 6.02 Seals FFKM & PTFE Contact Manufacturer 7. DIMENSIONS Metric Imperial 7.01 Height (overall) 267 mm in 7.02 Diameter 120 mm 4.72 in 8. WEIGHT Metric Imperial kg 30 lb 9. PANEL MOUNT REQUIREMENTS Metric Imperial 9.01 Maximum Panel Thickness 7 mm 0.28 in 9.02 Mounting Hole Diameter 46 mm 1.8 in NOTES: FLOW RATE: Reference Flow Rate Guide for appropriate flow rate. * Depends on characteristics of media. ** Maximum Flow Rate with Methanol = 1370 LPH *** Inlet Pressure: Minimum recommended pressure supplied by pump to valve. **** Minimum Pressure Drop Across Valve: a.) Differential pressure can be set to customer requirements between 7-10 p. b.) A lower differential pressure drop can be accommodated; however, the turn-down ration will be reduced. TURNDOWN RATIO: ***** Turndown ratio can vary dependent upon chemical composition, flow rate, and p. FILTRATION: Filtration to 50 Micron is recommended. Some chemicals may require finer filtration because of emulsions. US PATENTS: 5,427,139 * 5,494,070 * 6,189,564,B1 * EU PATENT * Rev. C, 04/16 Page 4 of 7

5 ORDER GUIDE REFERENCE ORDER GUIDE DISCLAIMER There are a number of factors involved in the smooth operation of an Amflow valve. As the Amflow valve is custom built specifically to meet the end user s criteria, it is critical that Amflow receive accurate information. That information should include, among other things, the desired minimum & maximum flow rate AND pressure. Based on the concept that the inherent nature of any given media being processed through a valve is not linear in nature, the flow rate represented on the order guide reflect the options available to reach a flow rate within specific ranges using H2O. US PATENTS: 5,427,139 * 5,494,070 * 6,189,564,B1 * EU PATENT * Rev. C, 04/16 Page 5 of 7

6 ORDER GUIDE PRODUCT PRODUCT TYPE MATERIAL SEAL FLOW RATE Max. H2O* PORT TYPE ASSEMBLY PH SS -015 TITANIUM -002 DUPLEX 2205 SUPER DUPLEX FFKM LPH 001 SF750CX -03 SPECIAL ORDER -SO COMPLETE ORDER NUMBER: EXAMPLE TO ORDER: AM9A Flow Control Valve in 17-4 PH SS with FFKM Seals, 200 LPH Flow Rate And SF750CX Ports YOU WOULD ORDER #: US PATENTS: 5,427,139 * 5,494,070 * 6,189,564,B1 * EU PATENT * Rev. C, 04/16 Page 6 of 7

7 REPRESENTATIVES AMFLOW NORGE Norway, Sweden, Denmark, Netherlands, Germany, U.K., Italy Prinsens vei Sandnes Norway Telephone: Fax: AMFLOW CONTROLS ASIA SDN. BHD. Malaysia, Indonesia, Singapore, India, Thailand, Vietnam No Block 1, TTDI ADINA Jalan Judo 13/45, Seksyen Shah Alam, Selangor Malaysia Telephone: (+603) Mobile: (+6012) SUDIFLOW INTERGRATED SERVICES, LTD. Nigeria 25 Elelenwo Road Port Harcourt, Nigeria Telephone: , Amflow Copyright 2016 A & H Enterprises, Inc. All rights reserved A & H Enterprises, Inc NE 116th Street TEL: Kirkland, WA USA FAX: ah@amflow.com * Rev. C, 04/16 Page 7 of 7