LPS 1 GREASELESS LUBRICANT

Transcription

1 H2 PACKAGE SIZES Net Contents 11 wt.oz. / 312 g/ 379 ml aerosol 20 fl.oz. (591 ml) trigger spray 144 single wipes per case 1 gal. (3.78 L) 5 gal. (18.93 L) 55 gal. (208 L) 312 g/ 11 wt.oz. /379 ml aerosol (Canada) APPLICATIONS Cables Circuit Breakers Electric Motors Electronic Connectors Generators LPS 1 GREASELESS LUBRICANT LPS 1 Greaseless Lubricant is specially formulated to penetrate minute crevices, displace moisture, and leave behind a thin, dry lubricating film. It is the top choice for drying out critical electrical/electronic components and lubricating precision instruments. Hinges Ignition Systems Locks Micrometers Molds Part No C30116 FEATURES Provides a dry, thin, lubricating film Resists oil, dust, and dirt build-up Removes carbon build-up from surfaces Displaces moisture Loosens rusted or frozen parts Provides a short term, light, corrosion resistant barrier Ideal for delicate mechanisms Safe on paint, fabric, and most plastics Non-conductive Used worldwide in aviation VOC compliant in all 50 states NSF Registered H2 Acceptable for use in Canadian Food Processing Establishments SPECIFICATIONS AND APPROVALS Approved/Qualified to: Allied Signal ES-2092 Boeing B Task C00 Bombardier (Canadair) BAMS Delta Airlines Lockheed Martin EPSN G Pratt & Whitney Canada CPMC Rev. C Rolls Royce Overhaul Process 340 Nonfood Compounds Program Listed Category Code: H2 Registration # (Aerosol); # (Bulk) Acceptable for use in Canadian Food Processing Establishments MIL-C-23411A NSN (11 wt. oz.) NSN (11 wt. oz.) NSN (5 gal.) Nuts and Bolts Precision Open Gears Power Tools Relays Sliding Mechanisms Switch Gears Weapon cleaner LUBRICANT/PENETRANT TECHNICAL DATA SHEET

2 LPS 1 GREASELESS LUBRICANT Scan QR Code to view demo video of LPS 1 or go to product-videos PROPERTIES Appearance/physical state Liquid Flammable limits (estimated) Upper: 7.0% Lower: 0.6% Color Pale amber Auto-ignition temperature > 442 F (> 228 C) Odor Characteristic VOC Aerosol: <25% per U.S. State and Federal Consumer Product Regulations Bulk: <25% per U.S. State and Federal Consumer Product Regulations Vapor pressure < C Evaporation rate < 0.1 (BuAc = 1) Vapor density > 1 Viscosity < C Boiling point 415 F (213 C) Percent volatile 95 96% Solubility (water) Not soluble Dielectric strength 32 kv Specific gravity C Flash point 175 F (79 C) TCC-dispensed liquid DIRECTIONS Mix well before using. Spray on clean surface. Use attached extension tube for pinpoint application. Safe to use on plastic, rubber and paint. Use only in well ventilated areas. Avoid all sources of ignition (spark or flame). STORAGE Keep container in a cool, well-ventilated area. Avoid all sources of ignition (spark or flame). Store between 40 F (5 C) and 120 F ( 49 C). Store aerosols as Level 3 Aerosol (NFPA 30B). Store all materials in a dry, well-ventilated area. Avoid breathing vapors. DISPOSAL INFORMATION Waste must be disposed of in accordance with any and all applicable environmental control rules and/or regulations. MATERIAL SAFETY DATA SHEETS AVAILABLE UPON REQUEST OR VISIT OUR WEB SITE : LPS Laboratories An Illinois Tool Works Company 4647 Hugh Howell Road Tucker, GA TEL: (800) or (770) FAX: (800) or (770) Internet Web Site: LPS Laboratories LPS and LPS 1 are registered trademarks of Illinois Tool Works Printed in U.S.A. All Rights Reserved Form #TDS_00116 Rev. 10/2013

3 H2 PACKAGE SIZES Net Contents 11 wt.oz. / 312 g/ 380 ml aerosol 20 fl.oz. (591 ml) trigger spray 1 gal. (3.78 L) 5 gal. (18.93 L) 55 gal. (208 L) 312 g/ 11 wt.oz. /379 ml aerosol (Canada) LPS 2 HEAVY-DUTY LUBRICANT LPS 2 Heavy-Duty Lubricant will penetrate, lubricate, and protect against corrosion. Its strong multipurpose capabilities allow its use in a variety of industrial applications. LPS 2 does not contain harmful chlorinated solvents and it is safe for use on most surfaces. Part No C30216 FEATURES Strong, multi-purpose lubricant, and penetrant Provides a non-drying, light, oily film for use on indoor/outdoor equipment Reduces wear caused by friction and corrosion Loosens rusted or frozen parts Provides up to one year of corrosion protection on steel parts Nonfood Compounds Program Listed Category Code: H2 Registration # (aerosol); # (bulk) SPECIFICATIONS AND APPROVALS Approved/Qualified to: Boise Cascade Canadian Food Inspection Agency Chrysler Corporation City Public Service Cummins Engine Dresser Rand Ford Motor Co. Halliburton Honda Corp. Inland Steel Kimberly-Clark Koch Refining Group Kodak Lockheed Martin CPC 2c & 3b lubricating Lockheed Martin EPSN G39.04 MIL-C-23411A MIL-C-81309D Type III MIL-PRF-16173E Grade 3 Class 1 Minntac - US Steel New York City Transit NSF International Occidental Chemicals Pratt & Whitney Canada CPMC Rev. C Shell Oil Tyco Electronics Tyson UPS M B LUBRICANT/PENETRANT TECHNICAL DATA SHEET APPLICATIONS Bearings & valves Cables & linkages Dies, bits & fasteners Engines & electric motors Metal parts Parts in storage Production equipment Pulleys & rollers Slides & tracks

4 LPS 2 HEAVY-DUTY LUBRICANT PROPERTIES Appearance/physical state Liquid Flammable limits (estimated) Upper: 7.0% Lower: 0.6% Color Brown Auto-ignition temperature > 442 F (> 228 C) Odor Petroleum/cherry VOC Aerosol: 0% per U.S. State and Federal Consumer Product Regulations Bulk: 0% per U.S. State and Federal Consumer Product Regulations Vapor pressure < C Evaporation rate < 0.1 (BuAc = 1) Vapor density 4.7 Viscosity <7 25 C Boiling point 383 F (195 C) Percent volatile 92 95% Solubility (water) 3% Dielectric strength 33 kv Specific gravity C Flash point 175 F (79 C) TCC-dispensed liquid DIRECTIONS Mix well before using. Spray on clean surface. Use attached extension tube for pinpoint application. Safe to use on plastic, rubber and paint. Use only in well ventilated areas. Avoid all sources of ignition (spark or flame). STORAGE Keep container in a cool, well-ventilated area. Avoid all sources of ignition (spark or flame). Store between 40 F (5 C) and 120 F ( 49 C). Store aerosols as Level 3 Aerosol (NFPA 30B). Store all materials in a dry, well-ventilated area. Avoid breathing vapors. DISPOSAL INFORMATION Waste must be disposed of in accordance with any and all applicable environmental control rules and/or regulations. MATERIAL SAFETY DATA SHEETS AVAILABLE UPON REQUEST OR VISIT OUR WEB SITE : LPS Laboratories An Illinois Tool Works Company 4647 Hugh Howell Road Tucker, GA TEL: (800) or (770) FAX: (800) or (770) Internet Web Site: LPS Laboratories LPS is a registered trademark of Illinois Tool Works Printed in U.S.A. All Rights Reserved Form #TDS_00216 Rev. 10/2013

5 H2 LPS 3 PREMIER RUST INHIBITOR LPS 3 Premier Rust Inhibitor is a specially formulated long-term corrosion inhibitor protecting metal parts in inside storage for up to two years. When applied it forms a soft, transparent, waxy film sealing out moisture, air, acid, alkali fumes, and other corrosive elements. FEATURES Protects for up to 2 years indoors Prevents rust and corrosion Provides non-sling lubrication Self-healing, soft, waxy film Penetrates to displace moisture Inhibits exfoliation and filiform corrosion of aluminum Safe on all metals NSF Certified: H2 Registration # (Aerosol); # (Bulk) Acceptable for use in Canadian Food Processing Establishments SPECIFICATIONS AND APPROVALS Approved/Qualified to: ASTM F-945 Bombardier dehavilland DHMS C4.12 Type I Grade 3 Embraer EMB 120 Brasilia C.P.M. 120/1811 Type A-1 Lockheed Martin EPSN G Lockheed Martin Heavy Duty CPC 2b McDonnell Douglas DMS 2150 Pratt & Whitney PWA Pratt & Whitney Canada LCPMC Rev. D Saab 340 Maintenance Manual United Airlines United Technologies USBI MIL-C-83933A MIL-PRF-16173E Grade 2 Class 1 NSN (11 wt. oz.) NSN (1 gal.) CORROSION INHIBITOR TECHNICAL DATA SHEET PACKAGE SIZES Net Contents 11 wt.oz. / 312 g/ 380 ml aerosol 20 fl.oz (591 ml) trigger spray 1 gal. (3.78 L) 5 gal. (18.93 L) 55 gal. (208 L) 312 g/ 11 wt.oz. /380 ml aerosol (Canada) Part No C30316 APPLICATIONS Aircraft fuselages Metal parts Battery terminals Offshore drilling equipment Cables, chains, and pulleys Outdoor electrical connections Cargo sections Outdoor storage and Elevators shipments Interior sections of vehicle doors Pumps and hose assemblies

6 LPS 3 PREMIER RUST INHIBITOR PROPERTIES Appearance/physical state Hazy Liquid Color Brown Odor Mild Cherry Vapor pressure Boiling/Condensation point F( C) Specific gravity (water=1) Solubility in water Aerosol: 307 F (153 C) Bulk: 354 F (179 C) Aerosol: C Bulk: C Aerosol: 5% in water Bulk: Negligible Flash point F( C) Flash point method Auto ignition Temperature F( C) Aerosol: ~4860 C Bulk: C Aerosol: <73 F (23 C) Bulk: 104 F (40 C) Tag-Closed Cup Aerosol: >446 F (230 C) dispensed liquid Bulk: 469 F (246 C) VOC Aerosol: 64% per U.S. State & Federal Consumer Product Regulations Bulk: 79.1% per U.S. State & Pour Point F( C) 0 F (-18 C) Federal Consumer Product Regulations Flammable limits (estimated) Lower: 1.0% Upper: 7.0% Viscosity C Volatiles Aerosol: 70% 80% Bulk: 70% 90% Coverage per gallon 401 ft 2 4 wet mils Wet Film Thickness 3 7 mils Dry Film Thickness 1 3 mils Humidity Cabinet Test (ASTM D 1748) No rust on 1029 steel panels after 30 days Salt Spray Cabinet Test (ASTM D 177) Propellant Carbon Dioxide Corrosion Protection Dry Time to Handle 6 8 hours Full Cure 24 hours No corrosion on 2024-T3 aluminum panels after 1500 hours Indoors: up to 2 years Outdoors: 9 months Dielectric Strength 19.5kV HMIS 1996 Aerosol: 1, 3, 0 Bulk: 1, 2, 0 Temperature Range F( C) -40 F 175 F (-40 C 79 C) HMIS III Aerosol: 1, 4, 2 Bulk: 1, 2, 0 Spray Pattern Cone shaped mist HANDLING DO NOT spray into or around ignition sources. DO NOT allow material to come in contact with eyes or skin. Wear appropriate protective equipment during handling. Keep container closed. Avoid breathing vapors or mists. Use only with adequate ventilation. Wash hands and contaminated clothing thoroughly after handling. DIRECTIONS STORAGE Keep container in a cool, well-ventilated area. Avoid all sources of ignition (spark or flame). Store between 40 F and 120 F (4.4 C and 49 C). Store aerosols as Level 3 Aerosol (NFPA 30B). Store all materials in a dry, well-ventilated area. Avoid breathing vapors. Aerosol: Shake well before using. Hold can 8 to 12 inches away from surface to be sprayed. Apply a light, even coat. For best results use at room temperature, 70 F (21 C). Attach extension tube for difficult to reach areas. Wipe off any excess. If an additional coat is desired, allow a minimum of 3 hours cure before applying second coat. Use only in well ventilated area. Avoid all sources of ignition (spark or flame). Bulk: Stir container with mechanical stirrer to ensure product consistency. Brush, roll, or spray light even coat onto metal surface using paint sprayer or airless spray equipment. For best results use at room temperature 70 F (21 C). Wipe off any excess. If an additional coat is desired, allow a minimum of 3 hours cure before applying second coat. Use only in well ventilated area. Avoid all sources of ignition (spark or flame). Always use proper personal protective equipment as listed on MSDS. ADDITIONAL INFORMATION Removal Information: Removal of LPS 3 is best accomplished using a solvent such as LPS PreSolve or LPS A-151 (mineral spirits will suffice but may require more time to remove). Apply degreaser via spraying, brushing or roller. Allow degreaser to dwell for 5-10 minutes on surface. Agitation on surface with stiff brush may increase the effectiveness. Dwell time may vary depending on corrosion inhibitor thickness. Remove by wiping with absorbent rags or by scraping. Repeat process if complete removal is not achieved. Dispose of waste according to local and federal regulations. MATERIAL SAFETY DATA SHEETS AVAILABLE UPON REQUEST OR VISIT OUR WEB SITE : LPS Laboratories An Illinois Tool Works Company 4647 Hugh Howell Road Tucker, GA TEL: (800) or (770) FAX: (800) or (770) Internet Web Site: LPS Laboratories LPS, LPS 3, and PreSolve are registered trademarks of Illinois Tool Works Printed in U.S.A. All Rights Reserved Form #TDS_00316 Rev. 1/2014