Restoring Corrosion Protection Following Repair

Size: px
Start display at page:

Download "Restoring Corrosion Protection Following Repair"

Transcription

1 SECTION : Body Repairs 2009 Mustang Workshop Manual GENERAL PROCEDURES Procedure revision date: 09/05/2008 Restoring Corrosion Protection Following Repair Special Tool(s) Rust Inhibitor Installation Kit Undercoating Spray Gun Material Item Motorcraft Metal Surface Prep ZC-31-A Motorcraft Premium Undercoating PM-25-A Motorcraft Premium Undercoating Quart PM-25-B Motorcraft Rust Inhibitor Aerosol PM-24-A Motorcraft Rust Inhibitor Quart PM-24-B Specification WARNING: Always refer to Material Safety Data Sheet (MSDS) when handling chemicals and wear protective equipment as directed. Examples may include but are not limited to respirators and chemically resistant gloves. Failure to follow these instructions may result in serious personal injury. WARNING: Always wear protective equipment including eye protection with side shields, and a dust mask when sanding or grinding. Failure to follow these instructions may result in serious personal injury. NOTICE: Drilling access holes in body panels is not recommended. Drilling holes will break the original paint finish and promote corrosion. NOTE: Corrosion protection needs to be restored whenever it is necessary to sand or grind through painted surfaces or E-coat, or when bare metal repairs are made. NOTE: Refer to product label for preparation and handling instructions. 1. The surfaces must be free of oil, dirt and other foreign material. Carry out the process in the following sequence. 1. Thoroughly clean and degrease metal surfaces using metal surface prep to remove wax and grease. 2. For best results, the vehicle should be at room temperature. Attach the rust inhibitor canister to the

2 Rust Inhibitor Installation Kit Rust inhibitor should be applied after the welding and refinishing process. Product cannot be welded through. 4. Air pressure setting for applicator gun is kpa (65-75 psi). Use the long wand when spraying enclosed areas. The spray nozzle provides a 360-degree spray pattern. Insert the wand as far as possible into the access hole, pull the trigger and wait 2-3 seconds and slowly pull the wand out of the access hole. The short, hook-shaped wand sprays in one direction and must be rotated to provide complete coverage. Apply the material in light mist coats. Material displaces moisture. 5. Clean up any overspray with a mild solvent such as mineral spirits or bug and tar remover. NOTE: The following illustrations provide typical applications of body seams and spot welded flanges and are not vehicle specific. 2. NOTE: Door assembly lower view. Apply rust inhibitor as shown to the inside of the door shell on all the interior metal surfaces using the most suitable applicator wand. Apply material to the exposed edges after carrying out the welding process. Make sure horizontal surfaces are well protected as they are more susceptible to corrosion. Keep door drain holes clear to prevent moisture buildup. 3. NOTE: Quarter panel inner view. Apply rust inhibitor to the closed channel portion of the spot weld flange areas using the short, hookshaped wand. Apply material to the exposed edges after carrying out the welding process. Make sure horizontal surfaces are well protected as they are more susceptible to corrosion.

3 4. NOTE: Door frame opening view. Apply rust inhibitor to the closed channel portion of the spot weld flange areas using the short, hookshaped wand. Make sure horizontal surfaces are well protected as they are more susceptible to corrosion. Body and Frame Undercoating 1. WARNING: Always refer to Material Safety Data Sheet (MSDS) when handling chemicals and wear protective equipment as directed. Examples may include but are not limited to respirators and chemically resistant gloves. Failure to follow these instructions may result in serious personal injury. WARNING: Always wear protective equipment including eye protection with side shields, and a dust mask when sanding or grinding. Failure to follow these instructions may result in serious personal injury. NOTICE: Do not allow undercoating on powertrain components. Failure to follow these instructions may result in incorrect operation of these components. NOTE: Refer to product label for preparation and handling instructions.

4 NOTE: Avoid high-pressure water spray cleaning to treated underbody area for 24 hours. Wire brush the area and make sure the surfaces are free of oil, dirt and other foreign material. Carry out the undercoating process in the following sequence. 1. Thoroughly clean and degrease metal surfaces using metal surface prep to remove wax and grease. 2. For best results, the vehicle should be at room temperature. Canister attaches directly to the dispensing gun. Attach the undercoating canister to the Undercoating Spray Gun Undercoat should be applied after the welding and refinishing process. Product cannot be welded through. 4. Air pressure setting for applicator gun is kpa (80-90 psi). Apply light mist coats, applicator sprays in fogging pattern. Material displaces moisture. 5. Clean up any overspray with a mild solvent such as mineral spirits or bug and tar remover. NOTE: The following illustrations provide typical applications to frame rails and are not vehicle specific. 2. NOTE: Frame rail exterior spot-weld flange view. Apply undercoat material to the exterior exposed edges after carrying out the welding and refinishing process. 3. NOTE: Cross section view of typical unibody frame rail shown. Apply rust inhibitor to the inner surfaces of the rail after carrying out welding process. Use the long wand and insert as far as possible, depress trigger and wait 2-3 seconds and slowly pull the wand to make sure the area is completely fogged.

5 4. NOTE: Full frame vehicle, front rail-to-mid rail section repair shown. Apply undercoat material to the exposed surfaces after carrying out the welding process. Make sure to completely cover any bare metal areas.

6

Frame Members Rear. Special Tool(s) Rust Inhibitor Installation Kit Undercoating Spray Gun

Frame Members Rear. Special Tool(s) Rust Inhibitor Installation Kit Undercoating Spray Gun SECTION 501-35: Body Repairs 2009 Mustang Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 04/03/2009 Frame Members Rear Special Tool(s) Rust Inhibitor Installation Kit 286-00002 Undercoating

More information

CORROSION PROTECTION CORROSION PROTECTION FEATURING RUST MORT RUST SEAL RUST TRAP RUST SHIELD RUST PREVENTER CAVITY WAX UNDERCOATINGS COMPARISON CHART

CORROSION PROTECTION CORROSION PROTECTION FEATURING RUST MORT RUST SEAL RUST TRAP RUST SHIELD RUST PREVENTER CAVITY WAX UNDERCOATINGS COMPARISON CHART CP 0317 CORROSION PROTECTION CORROSION PROTECTION FEATURING RUST MORT RUST SEAL RUST TRAP RUST SHIELD RUST PREVENTER CAVITY WAX UNDERCOATINGS COMPARISON CHART RUST MORT WHEN TO USE IT: For the conversion

More information

2008 Crown Victoria/Grand Marquis Workshop Manual. REMOVAL AND INSTALLATION Procedure revision date: 01/25/2010

2008 Crown Victoria/Grand Marquis Workshop Manual. REMOVAL AND INSTALLATION Procedure revision date: 01/25/2010 SECTION 501-35: Body Repairs 2008 Crown Victoria/Grand Marquis Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 01/25/2010 Ballistic Door Panel Special Tool(s) Heavy Duty Riveter 501-D011

More information

Underbody Dimensions 4-Door 904

Underbody Dimensions 4-Door 904 Underbody Dimensions Wagon NOTE: Measurements are obtained on center, unless otherwise indicated. Underbody Dimensions 4-Door 904 SECTION 501-35: Body Repairs DESCRIPTION AND OPERATION Procedure revision

More information

CP01S Corrosion Protection

CP01S Corrosion Protection Uniform Procedures For Collision Repair CP01S Corrosion Protection 1. Description This procedure describes repair methods and inspection requirements for the application of corrosion protection materials

More information

SECTION Body Repairs

SECTION Body Repairs 501-35-i Body Repairs 501-35-i SECTION 501-35 Body Repairs CONTENTS PAGE Frame Members Front... 501-35-2 501-35-2 Body Repairs 501-35-2 Frame Members Front Special Tool(s) Rust Inhibitor Installation Kit

More information

GENERAL GUIDELINES FOR THE APPLICATION OF TECTYL AUTO/TRUCK/TRAILER RUSTPROOFING COMPOUNDS

GENERAL GUIDELINES FOR THE APPLICATION OF TECTYL AUTO/TRUCK/TRAILER RUSTPROOFING COMPOUNDS Number 17 GENERAL GUIDELINES FOR THE APPLICATION OF TECTYL AUTO/TRUCK/TRAILER RUSTPROOFING COMPOUNDS A. Equipment 1) Airless type spray equipment, designed for fluid pressure atomization. The spray gun

More information

SP91S Trunk Floor. Copyright 1999 Inter-Industry Conference On Auto Collision Repair v.4.0

SP91S Trunk Floor. Copyright 1999 Inter-Industry Conference On Auto Collision Repair v.4.0 Uniform Procedures For Collision Repair SP91S Trunk Floor Copyright 1999 Inter-Industry Conference On Auto Collision Repair v.4.0 1. Description This procedure describes the repair and complete or partial

More information

RF41 Finish Application

RF41 Finish Application Uniform Procedures For Collision Repair RF41 Finish Application 1. Description This procedure describes methods for applying paint finishes. Inspection and evaluation requirements are also included. 2.

More information

FR11S Fender, Welded-On

FR11S Fender, Welded-On Uniform Procedures For Collision Repair UPCR FR11S Fender, Welded-On 1. Description This procedure describes the repair and complete replacement of a welded-on steel fender. Inspection and evaluation requirements

More information

The Core Four Solutions

The Core Four Solutions 3M Tech Talk: The Core Four Solutions to Complete Corrosion Protection Have you ever seen a vehicle that has corrosion on only one panel? Do you then wonder why just one panel has corroded while the same

More information

HOW - TO SCRATCH & DENT REPAIRS

HOW - TO SCRATCH & DENT REPAIRS HOW - TO SCRATCH & DENT REPAIRS Tool And Material Checklist Wax and Grease Remover Sandpaper Assortment and Sanding Block Tack Cloth and Lint-free Cloths Glazing Putty Rubber Contour Squeegee Body Filler

More information

Copyright 1999 Inter-Industry Conference On Auto Collision Repair v.4.0

Copyright 1999 Inter-Industry Conference On Auto Collision Repair v.4.0 Uniform Procedures For Collision Repair UPCR SP11S Frame Copyright 1999 Inter-Industry Conference On Auto Collision Repair v.4.0 1. Description This procedure describes the repair and complete or partial

More information

SECTION Glass, Frames and Mechanisms

SECTION Glass, Frames and Mechanisms 501-11-i Glass, Frames and Mechanisms 501-11-i SECTION 501-11 Glass, Frames and Mechanisms CONTENTS PAGE Windshield Glass... 501-11-2 501-11-2 Glass, Frames and Mechanisms 501-11-2 Windshield Glass Special

More information

ATD PIECE HVLP SPRAY GUN SET INSTRUCTION MANUAL

ATD PIECE HVLP SPRAY GUN SET INSTRUCTION MANUAL ATD-6904 6 PIECE HVLP SPRAY GUN SET INSTRUCTION MANUAL Read this manual carefully and understand it completely. Retain manual for future use. Always follow safety precautions to prevent personal injury

More information

ATD MM TOUCH UP GUN W/CUP INSTRUCTION MANUAL

ATD MM TOUCH UP GUN W/CUP INSTRUCTION MANUAL ATD-6903 1.0MM TOUCH UP GUN W/CUP INSTRUCTION MANUAL Read this manual carefully and understand it completely. Retain manual for future use. Always follow safety precautions to prevent personal injury and/or

More information

ATD MM PRIMER GUN W/CUP INSTRUCTION MANUAL

ATD MM PRIMER GUN W/CUP INSTRUCTION MANUAL ATD-6902 1.8MM PRIMER GUN W/CUP INSTRUCTION MANUAL Read this manual carefully and understand it completely. Retain manual for future use. Always follow safety precautions to prevent personal injury and/or

More information

Revised April High School Graduation Years 2016, 2017 and 2018

Revised April High School Graduation Years 2016, 2017 and 2018 Unit/Standard Number High School Graduation Years 2016, 2017 and 2018 Autobody/Collision and Repair Technology/Technician CIP 47.0603 Task Grid Secondary Competency Task List 100 SAFETY 101 Establish general

More information

OEM APPROVED AND USED

OEM APPROVED AND USED OEM APPROVED AND USED Pro Form's Pliogrip Truck Line epoxy and urethane adhesives are part of a complete system designed for the most demanding bonding applications in the truck refinish industry. www.proformproducts.com

More information

Service Manual Trucks

Service Manual Trucks Service Manual Trucks Group 182 500 Rustproofing Cab VN, VHD PV776-TSP144735 Foreword The descriptions and service procedures contained in this manual are based on designs and methods studies carried out

More information

STRANDS AND STANDARDS

STRANDS AND STANDARDS STRANDS AND STANDARDS BASIC AUTOMOTIVE COLLISION REPAIR Course Description This course is the first in a sequence of courses that prepares individuals in repair and refinishing of uni-bodies and fenders

More information

Introduction to P1: About P1 Coatings and How to Prepare and Spray. United States - 4 December Jeff Bergmann -

Introduction to P1: About P1 Coatings and How to Prepare and Spray. United States - 4 December Jeff Bergmann - Introduction to P1: About P1 Coatings and How to Prepare and Spray United States - 4 December 2017 - Jeff Bergmann - jeff@eyecandycustomz.com INTRODUCTION AND APPLICATION GUIDE 1 Company Background Based

More information

Rust Bullet Automotive FAQ s

Rust Bullet Automotive FAQ s Rust Bullet Automotive FAQ s 1. What is the difference between Rust Bullet Standard (Gold Label) and Rust Bullet Automotive (Silver Label)? Both Rust Bullet Standard and Rust Bullet Automotive are industrial

More information

FOREWORD. Pub. No. RM029E RM427E

FOREWORD. Pub. No. RM029E RM427E FOREWORD This repair manual has been prepared as a supplement to TOYOTA SUPRA collision damaged repair manual to provide information on the repair methods (including cutting and welding operations, but

More information

LIQUID MEDIA BLASTER INSTRUCTIONS

LIQUID MEDIA BLASTER INSTRUCTIONS Item #20668 LIQUID MEDIA BLASTER INSTRUCTIONS Pressure Washer Not Included The EASTWOOD LIQUID MEDIA BLASTER is specifically designed to use high pressure water from a pressure washer as a source for powerful

More information

Fuel Additives. Turbo 108 Fuel Injector Cleaner. Turbo 108 Octane Boost 16 oz & 32 oz.

Fuel Additives. Turbo 108 Fuel Injector Cleaner. Turbo 108 Octane Boost 16 oz & 32 oz. Fuel Additives Turbo 108 Fuel Injector Cleaner Specially formulated to provide maximum engine performance in Fuel Injected gasoline engines Unclogs dirty injectors Eliminates hard starting and poor acceleration

More information

ATD-6810 SPRAY GUN W/CUP INSTRUCTION MANUAL

ATD-6810 SPRAY GUN W/CUP INSTRUCTION MANUAL ATD-6810 SPRAY GUN W/CUP INSTRUCTION MANUAL Read this Instruction Manual carefully and understand it completely, basic precaution should be strictly followed to prevent the damage to the tool and injury

More information

Standard Operating Procedures. Heavy Duty Truck Repair. 3M Automotive Aftermarket Division

Standard Operating Procedures. Heavy Duty Truck Repair. 3M Automotive Aftermarket Division Standard Operating Procedures Heavy Duty Truck Repair M Automotive Aftermarket Division Process for Success Standard Operating Procedures From metal and plastic repair, to sanding, paint finishing and

More information

RF81 Finish Defects. Copyright 1999 Inter-Industry Conference On Auto Collision Repair v.4.0

RF81 Finish Defects. Copyright 1999 Inter-Industry Conference On Auto Collision Repair v.4.0 Uniform Procedures For Collision Repair UPCR RF81 Finish Defects Copyright 1999 Inter-Industry Conference On Auto Collision Repair v.4.0 1. Description This procedure describes methods for correcting finish

More information

Pro Gun (Model: UCpro and UCPro Plus)

Pro Gun (Model: UCpro and UCPro Plus) Undercoating/Rustproofing Pro Gun (Model: UCpro and UCPro Plus) Professional Undercoating and Rustproofing gun designed to apply protective coatings such as waterborne and solvent based under coatings,

More information

Basic Automotive Collision Repair

Basic Automotive Collision Repair Basic Automotive Collision Repair EXAM INFORMATION Items 43 Points 45 Prerequisites NONE Grade Level 10-12 Course Length ONE SEMESTER DESCRIPTION This course prepares individuals to repair automotive,

More information

OPR Replacement Foxbody Floor Pans Pair (79-93 All)

OPR Replacement Foxbody Floor Pans Pair (79-93 All) OPR Replacement Foxbody Floor Pans Pair (79-93 All) Time Necessary: Approximately 40-hours Tools Required: Spot Weld Cutter Tool Corded Drill Center Punch MIG Welder (minimum recommended: 110VAC/135A)

More information

METAL BLACKENING SYSTEM

METAL BLACKENING SYSTEM Item #15357 METAL BLACKENING SYSTEM INSTRUCTIONS The Eastwood Metal Blackening System replicates the factory Black Oxide coating found on many automotive bolts and fasteners as well as numerous small parts.

More information

Perkins Statewide Articulation Agreement. Documentation item: Secondary Competency Task List Coversheet

Perkins Statewide Articulation Agreement. Documentation item: Secondary Competency Task List Coversheet Perkins Statewide Articulation Agreement Documentation item: Secondary Task List Coversheet The Secondary School agrees to: A. Implement the approved PDE Program(s) of Study. B. Provide assessment of student

More information

Airless Spray Gun INSTRUCTIONS DP psi (345 bar) Maximum Working Pressure

Airless Spray Gun INSTRUCTIONS DP psi (345 bar) Maximum Working Pressure INSTRUCTIONS DP-6376 Airless Spray Gun 5000 psi (345 bar) Maximum Working Pressure INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. Table of Contents Warnings......................................

More information

Copyright 1999 Inter-Industry Conference On Auto Collision Repair v.4.0

Copyright 1999 Inter-Industry Conference On Auto Collision Repair v.4.0 Uniform Procedures For Collision Repair UPCR SP08A Rail, Rear 1. Description This procedure describes the repair and complete or partial replacement of an aluminum rear rail. Inspection and evaluation

More information

Most dust and water leaks occur due to missing or mis-installed body sealer or components. The source of the leak is detected by:

Most dust and water leaks occur due to missing or mis-installed body sealer or components. The source of the leak is detected by: SECTION 501-00: Body System General Information 2009 Mustang Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 03/26/2010 Body System Material Seam Sealer TA-2 Item Silicone Gasket and Sealant

More information

January 2007 Product Information D8080

January 2007 Product Information D8080 GLOBAL REFINISH SYSTEM January 2007 Product Information D8080 D8080 UV Cured Primer Surfacer D8403 Surface Degreaser for UV Primer PRODUCT DESCRIPTION D8080 UV Cured Primer Surfacer is a unique UV cured

More information

5. Front Bumper FRONT BUMPER

5. Front Bumper FRONT BUMPER 5. Front Bumper A: REMOVAL 1) Disconnect the ground cable from battery. 2) Remove the front grille. 3) Remove the nine clips on the upper part of bumper. EXTERIOR/INTERIOR

More information

c/ Required pre-requisite procedure(s): PREP Rev.01 Pre-painted or Primed Aluminum cleaning Procedure

c/ Required pre-requisite procedure(s): PREP Rev.01 Pre-painted or Primed Aluminum cleaning Procedure a/title : Application Process for D200 on Pre-painted or Primed Aluminum b/ Description : This document explains the process of applying AquaSurTech D200 to pre-painted or primed aluminum using HVLP or

More information

Toyota Hydrobase Application

Toyota Hydrobase Application Toyota Hydrobase Application Basecoat and Fade-out process 1, CLEANING After sanding the surfacer clean the fade-out area with Toyota Hydro Cleaner Dry thoroughly. 2, SANDING The leading edge of the fade-out

More information

POR-15 Kits. Super Starter Kits $22.99

POR-15 Kits. Super Starter Kits $22.99 POR-15 Kits Super Starter Kits $22.99 We created the SUPER STARTER KIT in response to requests from customers anxious to try out the entire 3-step rust-stopping system, as well as those customers who need

More information

No Infrared Refrigerant Leak Detector

No Infrared Refrigerant Leak Detector No. 22791 Infrared Refrigerant Leak Detector Operator s Manual Product Description The Robinair No. 22791 uses infrared optics to create a refrigerant leak detector that combines sensitivity, speed, battery

More information

8. Front Bumper. Front Bumper A: REMOVAL EI FRONT BUMPER BEAM ASSEMBLY 1. FRONT BUMPER FACE

8. Front Bumper. Front Bumper A: REMOVAL EI FRONT BUMPER BEAM ASSEMBLY 1. FRONT BUMPER FACE 8. A: REMOVAL 1. FRONT BUMPER FACE 1) Disconnect the ground cable from the battery. 2) Remove the front grille. 3) Turn over the front mud guard, and remove the

More information

STAINLESS STEEL DETERGENT INJECTOR AW

STAINLESS STEEL DETERGENT INJECTOR AW STAINLESS STEEL DETERGENT INJECTOR AW-8000-0001 OPERATING INSTRUCTIONS & PARTS LIST CAUTION RISK OF INJURY! READ ENTIRE MANUAL BEFORE OPERATING! THIS MANUAL IS AN IMPORTANT PART OF THE INJECTOR AND MUST

More information

SOLVENT BORNE UNITS WITH WATER BORNE PAINT UNI-RAM CORPORATION ONTARIO CANADA

SOLVENT BORNE UNITS WITH WATER BORNE PAINT UNI-RAM CORPORATION ONTARIO CANADA USER MANUAL UM80 SERIES WALL MOUNT SPRAY GUN CLEANERS WATER BORNE UM80W, UM80WA,UM80WF SOLVENT BORNE CAUTION DO NOT USE WATER BORNE UNITS WITH SOLVENT BORNE PAINT OR SOLVENT BORNE UNITS WITH WATER BORNE

More information

2015 (LA) Challenger SRT Hellcat

2015 (LA) Challenger SRT Hellcat NUMBER: 23-031-14 GROUP: Body DATE: October 16, 2014 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored

More information

Hem Flange Rust Repair

Hem Flange Rust Repair Hem Flange Rust Repair 2016 and Prior GM Passenger Cars and Trucks This Bulletin also applies to any of the models that may be Export vehicles. This Bulletin has been revised to add the 2015-2016 Model

More information

OWNER'S MANUAL RED LINE EZ50

OWNER'S MANUAL RED LINE EZ50 OWNER'S MANUAL RED LINE EZ50 electrostatic powder coating gun Congratulations on your purchase of the RED LINE EZ50 electrostatic powder EZ50 coating gun. You could be a serious hobbyist or a first time

More information

Auto Detailing User Guide Part 1 Exterior & Part 2 Interior. Part 1 Exterior

Auto Detailing User Guide Part 1 Exterior & Part 2 Interior. Part 1 Exterior seperately Part 1 Exterior 1. Spot Cleaning Before washing the exterior of your vehicle, begin by spot cleaning of any particularly greasy, sticky, or dirty areas. Eco Green Auto Clean Freedom Multi-Purpose

More information

Procedure for Long-Term Storage of CYCLO DRIVE, BEIER VARIATOR, and BEIER-CYCLO VARIATOR

Procedure for Long-Term Storage of CYCLO DRIVE, BEIER VARIATOR, and BEIER-CYCLO VARIATOR 1/7 1. Notes on Using This Manual ---------------------------------------------------------------------------Page 1 of 7 2. Rust Prevention for Assembled Unit------------------------------------------------------------------Page

More information

SP06A Rail, Front Lower

SP06A Rail, Front Lower Uniform Procedures For Collision Repair SP06A Rail, Front Lower 1. Description This procedure describes the repair and complete or partial replacement of an aluminum front lower rail. Inspection and evaluation

More information

QTY 3D PART NO. DESCRIPTION

QTY 3D PART NO. DESCRIPTION QTY 3D PART NO. DESCRIPTION 1 691032 V6 FRONT AIR DAM 1 691023 SIDE SKIRT RIGHT 1 691024 SIDE SKIRT LEFT 1 691566 V6 DUAL EXHAUST REAR LOWER SKIRT- 8 3M 94 3M ADHESION PROMOTER 24 #8 X ¾ SELF DRILLING

More information

SP41A B-Pillar. Copyright 1999 Inter-Industry Conference On Auto Collision Repair v.4.0

SP41A B-Pillar. Copyright 1999 Inter-Industry Conference On Auto Collision Repair v.4.0 Uniform Procedures For Collision Repair SP41A B-Pillar 1. Description This procedure describes the repair and complete or partial replacement of an aluminum B-pillar assembly. Inspection and evaluation

More information

8. Front Bumper. Front Bumper A: REMOVAL EI FRONT BUMPER FACE. 5) For OUTBACK model, remove the side garnish of the front fender.

8. Front Bumper. Front Bumper A: REMOVAL EI FRONT BUMPER FACE. 5) For OUTBACK model, remove the side garnish of the front fender. 8. A: REMOVAL 1. FRONT BUMPER FACE 1) Disconnect the ground cable from the battery. 2) Turn over the front mud guard, and remove the clips connecting the fender and bumper. 5) For OUTBACK model, remove

More information

AUTOBASE PLUS SOLID, METALLIC AND PEARL COLORS (HP REDUCERS)

AUTOBASE PLUS SOLID, METALLIC AND PEARL COLORS (HP REDUCERS) Page 1 of 5 DESCRIPTION: Autobase Plus basecoat provides excellent coverage, metallic control and sprayability when used to duplicate OEM solid, metallic and pearl color effects. Autobase Plus must be

More information

Surface Preparation and Application of Ronass Pipe Shield 1319

Surface Preparation and Application of Ronass Pipe Shield 1319 Surface Preparation and Application of Ronass Pipe Shield 1319 RONASS TECHNICAL SUPPORT TEAM WWW.RONASS.COM SUPPORT@RONASS.COM PROTECTIVE COATINGS MARINE COATINGS DECORATIVE COATINGS Introduction Ronass

More information

ASSEMBLY AND OPERATING INSTRUCTION MANUAL

ASSEMBLY AND OPERATING INSTRUCTION MANUAL www.rainmakersprayers.com ASSEMBLY AND OPERATING INSTRUCTION MANUAL 18 VOLT LITHIUM ION BACKPACK SPRAYER-4 GALLON Product# 708910 Front View Back View Please read this manual for instructions and precautions

More information

SPECIFICATIONS Horsepower: 1.5 HP Running Maximum PSI: 125 PSI Tank Capacity: 15 Gallons CFM: 6 40 PSI 5 90 PSI

SPECIFICATIONS Horsepower: 1.5 HP Running Maximum PSI: 125 PSI Tank Capacity: 15 Gallons CFM: 6 40 PSI 5 90 PSI 15 GALLON AIR COMPRESSOR Model: 7678 DO NOT RETURN TO STORE Please call 800-348-5004 for parts and service CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials

More information

GENERAL INFORMATION 1 A IMPORTANT INFORMATION

GENERAL INFORMATION 1 A IMPORTANT INFORMATION GENERAL INFORMATION 1 A 23253 IMPORTANT INFORMATION Table of Contents Page How To Use This Manual.................. 1A-1 Page Numbering...................... 1A-1 Introduction..............................

More information

FRAME AND BUMPERS 13-1 FRAME AND BUMPERS CONTENTS

FRAME AND BUMPERS 13-1 FRAME AND BUMPERS CONTENTS J FRAME AND BUMPERS 13-1 FRAME AND BUMPERS CONTENTS BUMPERS... 5 BUMPERS... 16 FRAME... 1 FRAME... 10 FRAME INDEX Frame Dimensions... 1 Front Skid Plate... 1 Fuel Filler Hose Splash Shield XJ Vehicles...

More information

FR11A Fender, Welded-On

FR11A Fender, Welded-On Uniform Procedures For Collision Repair FR11A Fender, Welded-On 1. Description This procedure describes the repair and complete replacement of a welded-on aluminum fender. Inspection and evaluation requirements

More information

AUTOMOTIVE CARE. Lubricants Degreasers Rust Control - Cleaners Detailing Undercoatings Odor Neutralizers

AUTOMOTIVE CARE. Lubricants Degreasers Rust Control - Cleaners Detailing Undercoatings Odor Neutralizers Lubricants Degreasers Rust Control - Cleaners Detailing Undercoatings Odor Neutralizers www.emzone.ca Lubricants & Greases 45002 - Penetrating Lubricant 400 g / 14 oz Aerosol emzone PENETRATING LUBRICANT

More information

PENTECH, INC. BD Spray Gun. Operating Manual Parts Manual May, 2008 Issue 1. Plural Component, Impingement Mixing, Mechanical Purge Spray Gun

PENTECH, INC. BD Spray Gun. Operating Manual Parts Manual May, 2008 Issue 1. Plural Component, Impingement Mixing, Mechanical Purge Spray Gun PENTECH, INC. Operating Manual Parts Manual May, 2008 Issue 1 Plural Component, Impingement Mixing, Mechanical Purge Spray Gun BD Spray Gun PENTECH, INC. 7256 21 st Street East Sarasota, FL 34243 Phone:

More information

Handheld Tank Sprayer

Handheld Tank Sprayer Handheld Tank Sprayer Operator's Manual MODELS MS - 20 MS - 35 WARNING DANGER Read rules for safe operation and all instructions carefully. ECHO provides this Operator's Manual which must be read and understood

More information

(a) Short-term storage of tubeless wheel assemblies may be stored with the wheel o- ring packing installed between the two halves.

(a) Short-term storage of tubeless wheel assemblies may be stored with the wheel o- ring packing installed between the two halves. Manual AWBCMM0001-7.2/USA Section 300 External Design (2) Wheels Stored Without Tires Installed (a) Short-term storage of tubeless wheel assemblies may be stored with the wheel o- ring packing installed

More information

SP01A Rail, Front Upper

SP01A Rail, Front Upper Uniform Procedures For Collision Repair UPCR SP01A Rail, Front Upper 1. Description This procedure describes the repair and complete or partial replacement of an aluminum front upper rail. Inspection and

More information

16-17 PRODUCT CATALOGUE

16-17 PRODUCT CATALOGUE 16-17 PRODUCT CATALOGUE 2016-17 PRODUCT CATALOGUE CLEANUP PRODUCTS 1-2 Cleaners & Degreasers 1 Soaps 1 Dressings 2 Specialty Chemicals 2 PAINT RESTORATION & PROTECTION 3 Compounds 3 Polishes 3 Sealants

More information

LubeSite 500 Series. Grease, Metal Base, Corrosion Resistant. General. Application. Operation. Technical Data R0 06/09

LubeSite 500 Series. Grease, Metal Base, Corrosion Resistant. General. Application. Operation. Technical Data R0 06/09 LubeSite 500 Series Grease, Metal Base, Corrosion Resistant General LubeSite 500 Series are nickel-chrome, double-plated for applications where corrosive resistance is required, such as chemical and food

More information

99.95 Kit Kit Kit. Call to order: 4:1 Clear Coat 1 Gallon with Activator Medium or Fast $ Kit

99.95 Kit Kit Kit. Call to order: 4:1 Clear Coat 1 Gallon with Activator Medium or Fast $ Kit 4:1 Clear Coat with Activator Kit 4:1 Clear Coat with Activator 99.95 Kit 4:1 Original Speed Klearkote with Hardener 1 Kit Business Hours: Monday Saturday, 8 a.m. 6 p.m. Sunday, 10 a.m. 6 p.m. 4:1 Speed

More information

SECTION FIRST RESPONDER SERIES HEAVY DUTY PERSONNEL LOCKERS DEBOURGH MFG. CO. 10/15/2013

SECTION FIRST RESPONDER SERIES HEAVY DUTY PERSONNEL LOCKERS DEBOURGH MFG. CO. 10/15/2013 SECTION 10501 FIRST RESPONDER SERIES HEAVY DUTY PERSONNEL LOCKERS DEBOURGH MFG. CO. 10/15/2013 PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General

More information

Introduction to Automotive Collision Repair Technology

Introduction to Automotive Collision Repair Technology Introduction to Automotive Collision Repair Technology Introduction to Construction Materials Standard 01 Steel (Introduction to Construction Materials) Objective 01 I can explain steel strengths and the

More information

SERVICE INSTRUCTIONS FOR SEAL REPLACEMENT OF POWER GEAR HYDRAULIC LEVELING LEGS

SERVICE INSTRUCTIONS FOR SEAL REPLACEMENT OF POWER GEAR HYDRAULIC LEVELING LEGS SERVICE INSTRUCTIONS FOR SEAL REPLACEMENT OF POWER GEAR HYDRAULIC LEVELING LEGS 82-L0352 REV 8 4-27-2011 WARNING! HYDRAULIC COMPONENTS CAN CAUSE SERIOUS INJURY OR DEATH IF PROPER SAFETY PRECAUTIONS ARE

More information

June 2014 Product Information D8082

June 2014 Product Information D8082 GLOBAL REFINISH SYSTEM June 2014 Product Information D8082 D8082 UV - Cured Primer Surfacer D8783 Activator for UV-Cured Primer Surfacer PRODUCT DESCRIPTION D8082 UV-Cured Primer Surfacer offers a route

More information

Part# C3132/C Up Ford Mustang 8-Point Roll Bar

Part# C3132/C Up Ford Mustang 8-Point Roll Bar Part# C3132/C3156 2005-Up Ford Mustang 8-Point Roll Bar Installation Instructions Please read the instructions completely BEFORE starting this project. Competition Engineering 8-Point Roll Bars are not

More information

(Autobase Plus Metallic) 1x1 Increase distance and apply a metallic orientation coat if necessary.

(Autobase Plus Metallic) 1x1 Increase distance and apply a metallic orientation coat if necessary. Description Autobase Plus basecoat provides excellent coverage, metallic control and sprayability when used to duplicate OEM solid, metallic and pearl color effects. Autobase Plus must be used in conjunction

More information

AUTOMATIC AIRSPRAY GUN

AUTOMATIC AIRSPRAY GUN INSTRUCTION MANUAL AUTOMATIC AIRSPRAY GUN Manual : 0407 573.011.212 Date : 19/07/04 Supersede : KREMLIN REXSON - Site de Stains : 150, avenue de Stalingrad 93 245 - STAINS CEDEX - FRANCE Téléphone : 33

More information

Standard Operating Procedures. for Collision Repair

Standard Operating Procedures. for Collision Repair Standard Operating Procedures for Collision Repair M Automotive Aftermarket Division May 0 Process for Success Standard Operating Procedures From metal and plastic repair, to sanding, paint finishing and

More information

REV READ BEFORE INSTALLATION OF KIT:

REV READ BEFORE INSTALLATION OF KIT: REV. 05-08 QTY 3D PN. FCS PART NUMBER DESCRIPTION 1 691509 A7EDG-7820049-AAPLN EDGE BODY KIT- V6 B PCS & EXH TIPS 1 691256 A 7 E D G - 7 8 20049-BAPLN EDGE BODY KIT- V6 8PCS & EXH TIPS W/HITCH 1 691501

More information

Handout Activity: HA511

Handout Activity: HA511 Using a tire pressure gauge Engines: Motive Power Types: Handout Activity: HA511 HA511-2 Student/Intern information: Name Date Class Using a tire pressure gauge Summary There are two main types of tire

More information

Top Side Door Door Model Work Area Height Door Options Opening Opening Gun Options Weight

Top Side Door Door Model Work Area Height Door Options Opening Opening Gun Options Weight FLOOR MODEL STEEL CABINETS 40403 40413 Standard Features for All Models 100 CFM dust collector included with all steel cabinets HD 14 gauge steel - welded seams Full width top door Optional additional

More information

MGFHVLP. Instructions/Parts. Mini Gravity Feed System E. Part No Includes MGFHVLP Mini Gravity Feed Spray Gun and MGC 125 Gravity Cup.

MGFHVLP. Instructions/Parts. Mini Gravity Feed System E. Part No Includes MGFHVLP Mini Gravity Feed Spray Gun and MGC 125 Gravity Cup. Instructions/Parts MGFHVLP Mini Gravity Feed System FOR PRODUCT INFORMATION CALL: 1-800-742-7731 309989E For gravity feed spraying of automotive colors and clears. Ideal for touch-up and detail work. Important

More information

Changing the way things have always been done. Not only from the way we interact with the customer, but how our chemicals are made.

Changing the way things have always been done. Not only from the way we interact with the customer, but how our chemicals are made. Changing the way things have always been done. Not only from the way we interact with the customer, but how our chemicals are made. Large Vehicle and Equipment Cleaning Alkaline (High ph) Products Alkaline

More information

2002 Mustang Workshop Manual

2002 Mustang Workshop Manual Page 1 of 13 SECTION 303-01B: Engine 4.6L (2V) 2002 Mustang Workshop Manual REMOVAL Procedure revision date: 01/02/2003 Cylinder Heads Special Tool(s) Remover, Crankshaft Vibration Damper 303-009 (T58P-6316-D)

More information

P Original Series Cargo Van Lift Mounting Instructions Fullsize Ford Van present. Preparing the Gate

P Original Series Cargo Van Lift Mounting Instructions Fullsize Ford Van present. Preparing the Gate Fullsize Ford Van- 1992-present Preparing the Gate 1. Remove the mounting hardware which is banded to the liftgate. 2. Verify mounting kit (Figure 1 and Table 1). S-400-40 STRAP VAN MOUNTING EAR BENT BRACKET

More information

Walk-Behind Sprayer SL-80 & SL-80SS. Owner's Manual and Installation Instructions Original Instructions CAUTION

Walk-Behind Sprayer SL-80 & SL-80SS. Owner's Manual and Installation Instructions Original Instructions CAUTION April 15, 2017 Lit. No. 74419, Rev. 00 Walk-Behind Sprayer SL-80 & SL-80SS Owner's Manual and Installation Instructions Original Instructions CAUTION Read this document before operating or servicing the

More information

ATTENTION! READ BEFORE ATTACHING THE AIR HOSE

ATTENTION! READ BEFORE ATTACHING THE AIR HOSE Binks SV50 HVLP GRAVITY FEED SPRAY GUN & TOUCHUP GUN ATTENTION READ BEFORE ATTACHING THE AIR HOSE HVLP AIR SUPPLY REQUIREMENTS FULL SIZE GUN: 30 PSI inlet pressure provides 10 PSI at the air cap. Consumes

More information

Removal and Installation of the DD15 and DD16 Cylinder Head April Removal of the DD15 and DD16 Cylinder Head

Removal and Installation of the DD15 and DD16 Cylinder Head April Removal of the DD15 and DD16 Cylinder Head 4 102-12 1 4 102-12 SUBJECT DATE Removal and Installation of the DD15 and DD16 Cylinder Head April 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0081

More information

SU470LV / SUA470LV OC-35

SU470LV / SUA470LV OC-35 A Universal Ancillary Brand OC-35 ONECHOICE is a 1K adhesion promoter for use within all North American markets and is recommended for use under PPG and NEXA AUTOCOLOR branded undercoats and topcoats.

More information

2-1/4 Gallon Sprayer

2-1/4 Gallon Sprayer 2-/4 Gallon Sprayer 94008 ASSEMBLY AND OPERATING INSTRUCTIONS 349 Mission Oaks Blvd., Camarillo, CA 930 Visit our Web site at http://www.harborfreight.com Copyright 2005 by Harbor Freight Tools. All rights

More information

Hello! Read on! Just like the first day

Hello! Read on! Just like the first day Hello! If you are reading this, most likely, you are a car enthusiast and love Keeping Your Car Looking New However, you always longed for an authentic place to get your car done. Just like the first day

More information

Safe Work Instructions Tools and Equipment

Safe Work Instructions Tools and Equipment Safe Work Instructions Version 1.00! 23 March 2015 Table of Contents PURPOSE AND SCOPE...4 HAND TOOLS...6 ELECTRIC POWER TOOLS...7 PETROL POWERED TOOLS...9 PORTABLE ELECTRICITY GENERATOR...12 PNEUMATIC

More information

3-1, Shinchi, Fuchu-cho, Aki-gun Hiroshima , Japan TEL : 81(82) FAX : 81(82) Technical

3-1, Shinchi, Fuchu-cho, Aki-gun Hiroshima , Japan TEL : 81(82) FAX : 81(82) Technical Service Information 3-1, Shinchi, Fuchu-cho, Aki-gun Hiroshima 730-8670, Japan TEL : 81(82)287-5323 FAX : 81(82)287-5220 Category Coverage S Distributor only Please inform your dealers Technical Please

More information

SECTION 6 5 SERVICE PROCEDURES AND SPECIFICATIONS. Body

SECTION 6 5 SERVICE PROCEDURES AND SPECIFICATIONS. Body SECTION 6 5 SERVICE PROCEDURES AND SPECIFICATIONS Body Specifications 236 Protecting your vehicle from corrosion 237 Washing and waxing 238 Cleaning the interior 239 235 SPECIFICATIONS DIMENSIONS AND WEIGHT

More information

Frequently Asked Questions for Automotive Applications

Frequently Asked Questions for Automotive Applications Frequently Asked Questions for Automotive Applications Rust Bullet Automotive 1. What is the difference between Rust Bullet Standard formula (Gold Label) and Rust Bullet Automotive formula (Silver Label)?

More information

Copyright 1999 Inter-Industry Conference On Auto Collision Repair v.4.0

Copyright 1999 Inter-Industry Conference On Auto Collision Repair v.4.0 Uniform Procedures For Collision Repair DO21 Door Copyright 1999 Inter-Industry Conference On Auto Collision Repair v.4.0 1. Description This procedure describes the repair or replacement of a vehicle

More information

Installation instructions Mustang Window Tint

Installation instructions Mustang Window Tint Installation instructions Mustang Window Tint Tools Required: Supplied Tool Kit Heat Gun Spray Bottle Prep: Fill spray bottle with water, mixing in a few drops of baby shampoo. This helps with lubricity

More information

SB20G. Large Pressurized Abrasive Blaster Assembly & Operating Instructions

SB20G. Large Pressurized Abrasive Blaster Assembly & Operating Instructions SB20G Large Pressurized Abrasive Blaster Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. This manual provides

More information

36-1 DP PLEASE READ BEFORE USING THIS EQUIPMENT

36-1 DP PLEASE READ BEFORE USING THIS EQUIPMENT 36-1 DP PLEASE READ BEFORE USING THIS EQUIPMENT DP 36-1 Assembly Instructions PLEASE READ INSTRUCTIONS COMPLETELY BEFORE STARTING We thank you for purchasing the DP-36 pressure system. This system has

More information

AIRMIX PUMP and LOW-PRESSURE PUMP air motor with reversing block

AIRMIX PUMP and LOW-PRESSURE PUMP air motor with reversing block INSTRUCTION MANUAL AIRMIX PUMP and LOW-PRESSURE PUMP air motor with reversing block Manual : 0306 573.002.212 Date : 12/06/03 Supersedes : 17/06/02 Modif. 1 + 4 added KREMLIN REXSON Site de Stains : 150,

More information