Product Information. BTU + Total Treat (2410) BTU + Power Supplement & Cleaner (2420)

Transcription

1 Product Information BTU + Total Treat (2410) BTU + Power Supplement & Cleaner (2420) Diesel Fuel Improvers Reduce Emissions While Increasing Fuel Economy & Equipment Lifespan Using either of LE s two BTU + diesel fuel improvers, on- and off-road drivers are assured a clean engine and complete fuel combustion, which result in maximum fuel economy, longer equipment life, reduced emissions and a lower cost per mile or hour of operation. BTU + Total Treat (2410) and BTU + Power Supplement & Cleaner (2420) are both Ultra Low Sulfur Diesel (ULSD) compliant. BTU also includes a flow enhancer for better performance in cold temperatures. Beneficial Qualities Performance Boosts power Maintains smooth-running engine Provides superior rust and corrosion protection Disperses water better while dropping out free water Offers longer fuel stabilization Environment Lowers emissions Improves EGR system efficiency Helps reduce soot in oil Complies with ULSD standards Economy Ensures maximum fuel economy Requires less maintenance of fuel pumps and injectors, rings and valves Features economical treat rate with concentrated formula (1:1000 mix ratio is much higher than other aftermarket products) BTU + Total Treat (2410) Improves fuel lubricity Provides more complete combustion Cleans fuel system components, including pumps, injectors and combustion chamber Lowers pour point and cold filter plug point for enhanced coldweather performance, including easier starts BTU + Power Supplement & Cleaner (2420) Improves fuel lubricity Provides more complete combustion Cleans fuel system components, including pumps, injectors and combustion chamber The Lubrication Reliability Source

2 Technical Data BTU + Diesel Fuel Improvers (2410 & 2420) BTU + High Frequency Reciprocating Rig HFRR (ASTM D6079) BTU + Total Treat Cold Filter Plug Point Test CFPP (ASTM D6371) Performance Requirements Met or Exceeded ASTM D6079 ASTM D6371 BTU + Treat Rates Mix ratio 1:1000 Recommendations Mix ratio 1:1000. Store concentrate in warm area above 0 C (32 F). Typical Applications On-road and off-road diesel engines Improver 1 oz 2 oz 5 oz 10 oz 12 oz 16 oz* 32 oz 128 oz Fuel 8 gal 16 gal 40 gal 80 gal 96 gal 125 gal** 250 gal 1,000 gal Improver 30 ml 59 ml 148 ml 296 ml 355 ml 473 ml 946 ml 3,785 ml Fuel 30 L 59 L 148 L 296 L 355 L 473 L 946 L 3,785 L * 1 pint per tank ** Avg tank size/gal for OTR trucks LI Bailey Avenue Fort Worth, TX Fax: LE operates under an ISO 9001 Certified Quality System

3

4

5 LUBRICATION ENGINEERS, INC. P.O. Box 7128 FORT WORTH, TX MATERIAL SAFETY DATA SHEET SECTION I - PRODUCT IDENTIFICATION SUPPLIER: EMERGENCY TELEPHONE NUMBERS.: Lubrication Engineers, Inc. Company: (817) P.O. Box 7128 In the event of an emergency spill, fire, or exposure Call: Fort Worth, TX Chemtrec: (Within USA) (800) (Outside USA call collect) (703) CHEMICAL NAME AND SYNONYMS: TRADE NAME AND SYNONYMS: Not applicable 2410 BTU+ Total Treat CHEMICAL FAMILY: Hydrocarbon FORMULA: Not applicable SECTION II - TYPICAL CHEMICAL AND PHYSICAL PROPERTIES APPEARANCE: 210 F, 100 C, cst Light green fuel supplement Not applicable Not applicable ODOR: 100 F, 40 C, cst Lube oil odor Not applicable Not applicable RELATIVE DENSITY: SOLUBILITY IN WATER: PH: 6-8 (Air=1) >1 Negligible MELTING POINT: F POUR POINT: F Not applicable -17 BOILING POINT: F FLASH POINT: F (Method) Not determined 160 F (T.C.C.) VAPOR PRESSURE: SPECIFIC GRAVITY: (H 2 O=1) (mm 60 F) < SECTION III - INGREDIENTS WT PCT TLV ORAL DERMAL (APPROX) LD50 LD50 HAZARDOUS INGREDIENTS: Oil Mist (mineral) < mg/m 3 -TWA Unknown Unknown Diethylene glycol monomethyl ether Unknown Unknown Unknown Heavy aromatic naphtha ppm-twa Unknown Unknown Naphthalene ppm-twa Unknown Unknown 1,2-4-Trimethylbenzene <1.0 Unknown Unknown Unknown Vinyl acetate monomer < ppm-twa Unknown Unknown NON-HAZARDOUS INGREDIENTS: ADDITIVES AND/OR OTHER INGREDIENTS: This product is a mixture. The specific chemical identity of hazardous ingredients and non-hazardous ingredients, their C.A.S. numbers and their exact percent of composition are proprietary to Lubrication Engineers, Inc. and are being withheld as Trade Secrets. The above listing of hazardous ingredients discloses the properties, approximate concentration and known toxicological effects of the hazardous ingredients. This material is an automotive/fuel additive. The product is formulated with ingredients that are not designated as harmful to the ozone. REGULATORY INFORMATION: SARA Title III: This product does not contain any chemical substance on the SARA Extremely Hazardous Substances list. If this product contains any chemicals that are subject to the reporting requirements of Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 and 40 CFR Part 372, they will be listed in the above HAZARDOUS INGREDIENTS section. TSCA: This material is in compliance with the Toxic Substances Control Act (15 USC ) and all components of this product appear on the Toxic Substance Control Act (TSCA) inventory list. Clean Air Act: No ozone depleting chemicals listed in Title VI, Stratospheric Ozone Protection, Section 602 of the Clean Air Act are present or used in the manufacturing process of this product. SECTION IV - FIRE AND EXPLOSION HAZARD DATA FLASH POINT: F (Method) FLAMMABLE LIMITS: LEL UEL 160 F (T.C.C.) Unknown EXTINGUISHING MEDIA: Foam, dry chemical, water fog, or carbon dioxide SPECIAL FIRE FIGHTING PROCEDURES: Do not direct a solid stream of water into fire. Treat as a petroleum oil fire. Respiratory protection required for fire fighting personnel. UNUSUAL FIRE AND EXPLOSION HAZARDS: None SECTION V - HEALTH HAZARD DATA THRESHOLD LIMIT VALUE: (If Established) Not established. Oil mist = 5mg/m 3 10 ppm suggested EFFECTS OF OVEREXPOSURE: Although there are no consistent primary routes of entry, the product may cause mild dermatitis upon prolonged contact and is expected to be an eye and lung irritant. Any existing skin, eye, or lung irritation may be aggravated by direct contact. Slightly irritating to eyes, but does not injure eye tissue. Testing of vinyl acetate monomers show some evidence of animal carcinogenicity but the findings are questionable as to the significance to humans. SECTION VI - EMERGENCY AND FIRST AID PROCEDURES EYE CONTACT: Flush immediately with water until irritation subsides. Contact a physician. SKIN CONTACT: Wash affected skin area with mild soap and water BTU+ Total Treat Effective Date: January 19, 2005 Print Date: January 27, 2005 Page 1

6 INGESTION: Do not induce vomiting. Contact a physician. INHALATION: Remove to fresh air. If not breathing, give artificial respiration. Contact a physician. SECTION VII - REACTIVITY DATA STABILITY: (Thermal, Light, Etc.) CONDITIONS TO AVOID: Stable Contact with nuclear radiation and strong oxidizing materials. INCOMPATIBILITY: (Materials to avoid) Strong oxidizing materials. HAZARDOUS DECOMPOSITION PRODUCTS: Dense smoke; oxides of C, S, and N; hydrogen sulfide. HAZARDOUS POLYMERIZATION: Will not occur. SECTION VIII - SPILL OR LEAK PROCEDURES STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Remove all sources of ignition. Treat as a petroleum oil spill. WASTE DISPOSAL METHOD: Incinerate where permitted under federal, state, and local laws. Used petroleum products may be recycled through re-refining processes. SECTION IX - SPECIAL PROTECTION INFORMATION EYE PROTECTION: Sufficient to avoid direct contact. SKIN PROTECTION: Protective neoprene or plastic gloves may be desired. RESPIRATORY PROTECTION: Usually not needed in open, unconfined areas. In enclosed areas, sufficient ventilation to meet specified TWA-TLV. VENTILATION: Usually not needed in open, unconfined areas. In enclosed areas, sufficient ventilation to meet specified TWA-TLV. OTHER: Usually not needed. SECTION X - SPECIAL PRECAUTIONS Close containers when not in use. Keep away from heat, sparks, open flames, and strong oxidants. Avoid eye contact and prolonged skin contact. Avoid breathing oil mists. Wash thoroughly after handling. SECTION XI - HAZARD RATINGS There are several recognized and accepted systems that assign hazard ratings to materials. Although this product has not been evaluated specifically against these systems, the ratings for the National Fire Protection Association (NFPA) and the National Paint and Coatings Association's Hazardous Material Identification System (HMIS) are: NFPA HMIS Health 2 2 Flammability 2 2 Reactivity BTU+ Total Treat Effective Date: January 19, 2005 Print Date: January 27, 2005 Page 2

7 LUBRICATION ENGINEERS, INC. P.O. Box 7128 FORT WORTH, TX MATERIAL SAFETY DATA SHEET SECTION I - PRODUCT IDENTIFICATION SUPPLIER: EMERGENCY TELEPHONE NUMBERS.: Lubrication Engineers, Inc. Company: (817) P.O. Box 7128 In the event of an emergency spill, fire, or exposure Call: Fort Worth, TX Chemtrec: (Within USA) (800) (Outside USA call collect) (703) CHEMICAL NAME AND SYNONYMS: TRADE NAME AND SYNONYMS: Not applicable 2420 BTU+ Power Supplement and Cleaner CHEMICAL FAMILY: FORMULA: Hydrocarbon Not applicable SECTION II - TYPICAL CHEMICAL AND PHYSICAL PROPERTIES APPEARANCE: 210 F, 100 C, cst Orange fuel supplement Not applicable Not applicable ODOR: 100 F, 40 C, cst Lube oil odor Not applicable Not applicable RELATIVE DENSITY: SOLUBILITY IN WATER: PH: 6-8 (Air=1) >1 Negligible MELTING POINT: F POUR POINT: F Not applicable <-40 BOILING POINT: F FLASH POINT: F (Method) Not determined 167 F (T.C.C.) VAPOR PRESSURE: SPECIFIC GRAVITY: (H 2 O=1) (mm 60 F) < SECTION III - INGREDIENTS WT PCT TLV ORAL DERMAL (APPROX) LD50 LD50 HAZARDOUS INGREDIENTS: Oil Mist (mineral) < mg/m 3 -TWA Unknown Unknown Diethylene glycol monomethyl ether Unknown Unknown Unknown Heavy aromatic naphtha ppm-twa Unknown Unknown Naphthalene ppm-twa Unknown Unknown NON-HAZARDOUS INGREDIENTS: ADDITIVES AND/OR OTHER INGREDIENTS: This product is a mixture. The specific chemical identity of hazardous ingredients and non-hazardous ingredients, their C.A.S. numbers and their exact percent of composition are proprietary to Lubrication Engineers, Inc. and are being withheld as Trade Secrets. The above listing of hazardous ingredients discloses the properties, approximate concentration and known toxicological effects of the hazardous ingredients. This material is an automotive/fuel additive. The product is formulated with ingredients that are not designated as harmful to the ozone. REGULATORY INFORMATION: SARA Title III: This product does not contain any chemical substance on the SARA Extremely Hazardous Substances list. If this product contains any chemicals that are subject to the reporting requirements of Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 and 40 CFR Part 372, they will be listed in the above HAZARDOUS INGREDIENTS section. TSCA: This material is in compliance with the Toxic Substances Control Act (15 USC ) and all components of this product appear on the Toxic Substance Control Act (TSCA) inventory list. Clean Air Act: No ozone depleting chemicals listed in Title VI, Stratospheric Ozone Protection, Section 602 of the Clean Air Act are present or used in the manufacturing process of this product. SECTION IV - FIRE AND EXPLOSION HAZARD DATA FLASH POINT: F (Method) FLAMMABLE LIMITS: LEL UEL 167 F (T.C.C.) Unknown EXTINGUISHING MEDIA: Foam, dry chemical, water fog, or carbon dioxide SPECIAL FIRE FIGHTING PROCEDURES: Do not direct a solid stream of water into fire. Treat as a petroleum oil fire. Respiratory protection required for fire fighting personnel. UNUSUAL FIRE AND EXPLOSION HAZARDS: None SECTION V - HEALTH HAZARD DATA THRESHOLD LIMIT VALUE: (If Established) Not established. Oil mist = 5mg/m 3 10 ppm suggested EFFECTS OF OVEREXPOSURE: Although there are no consistent primary routes of entry, the product may cause mild dermatitis upon prolonged contact and is expected to be an eye and lung irritant. Any existing skin, eye, or lung irritation may be aggravated by direct contact. Slightly irritating to eyes, but does not injure eye tissue. No components are listed on OSHA, I.A.R.C., or N.T.P. lists for carcinogens. SECTION VI - EMERGENCY AND FIRST AID PROCEDURES EYE CONTACT: Flush immediately with water until irritation subsides. Contact a physician. SKIN CONTACT: Wash affected skin area with mild soap and water. INGESTION: Do not induce vomiting. Contact a physician. INHALATION: 2420 BTU+ Power Supplement and Cleaner Effective Date: January 19, 2005 Print Date: January 27, 2005 Page 1

8 Remove to fresh air. If not breathing, give artificial respiration. Contact a physician. SECTION VII - REACTIVITY DATA STABILITY: (Thermal, Light, Etc.) CONDITIONS TO AVOID: Stable Contact with nuclear radiation and strong oxidizing materials. INCOMPATIBILITY: (Materials to avoid) Strong oxidizing materials. HAZARDOUS DECOMPOSITION PRODUCTS: Dense smoke; oxides of C, S, and N; hydrogen sulfide. HAZARDOUS POLYMERIZATION: Will not occur. SECTION VIII - SPILL OR LEAK PROCEDURES STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Remove all sources of ignition. Treat as a petroleum oil spill. WASTE DISPOSAL METHOD: Incinerate where permitted under federal, state, and local laws. Used petroleum products may be recycled through re-refining processes. SECTION IX - SPECIAL PROTECTION INFORMATION EYE PROTECTION: Sufficient to avoid direct contact. SKIN PROTECTION: Protective neoprene or plastic gloves may be desired. RESPIRATORY PROTECTION: Usually not needed in open, unconfined areas. In enclosed areas, sufficient ventilation to meet specified TWA-TLV. VENTILATION: Usually not needed in open, unconfined areas. In enclosed areas, sufficient ventilation to meet specified TWA-TLV. OTHER: Usually not needed. SECTION X - SPECIAL PRECAUTIONS Close containers when not in use. Keep away from heat, sparks, open flames, and strong oxidants. Avoid eye contact and prolonged skin contact. Avoid breathing oil mists. Wash thoroughly after handling. SECTION XI - HAZARD RATINGS There are several recognized and accepted systems that assign hazard ratings to materials. Although this product has not been evaluated specifically against these systems, the ratings for the National Fire Protection Association (NFPA) and the National Paint and Coatings Association's Hazardous Material Identification System (HMIS) are: NFPA HMIS Health 2 2 Flammability 2 2 Reactivity BTU+ Power Supplement and Cleaner Effective Date: January 19, 2005 Print Date: January 27, 2005 Page 2