13.ANNEX I DIESEL ENGINE CONSTRUCTION CHARACTERISTICS INJECTION SYSTEM N CLIENT REV. PAGE HOLD N VENDOR. 0 3 of 8 HOLD N RM/PO HOLD

Transcription

1 0 3 of 8 13.ANNEX I DIESEL ENGINE ITEM N o. 62-EG-0 QUANT.: APPLICABLE TO: PROPOSAL PURCHASE AS BUILT 02 SERVICE : AUXILIARY GENERATOR DIESEL ENGINE TYPE / MODEL: 36B 03 DRIVEN EQUIPMENT: AUXILIARY GENERATOR MANUFACTURER :CATERPILLAR 04 ORIGIN : NATIONAL IMPORTED NATIONALIZATION INDEX, WEIGHTS (%) 0 VALUE (%) 0 05 OPERATING CONDITIONS PERFORMANCE POWER. k 1800 RPM (DIN-6270A) POWER. kw: 1800 RPM (DIN-6270A) 08 TORQUE.Nm: 1800 RPM (DIN-6270A) TORQUE.Nm: 1800 RPM (DIN-6270A) 09 ABSORVED CONTINUOUS POWER kw: 1889,2 POWER (SERVICE CONDITIONS). kw RPM (MIN.) 10 MAX. ABSORV. CONTINUOUS POWER kw: 1889,2 TORQUE (SERVICE CONDITIONS). Nm: RPM (MIN.) 11 SERVICE: CONTINUOUS INTERMITTENT SPARE FUEL CONSUMPTION. g/kwh : 100% LOAD 12 LOAD: CONSTANT VARIABLE NOISE LEVEL. db (A) (note 3): 1 m 13 INSTALLATION: SHELTERED UNSHELTERED MAXIMUM VIBRATION LEVEL (PEAK TO PEAK): mile 14 DESIGN TEMPERATURE. O C: 25(SAE J1995) CONSUMPTION OF LUBRICATING OIL. kg/h: 1,04 15 RELATIVE HUMIDITY. % : 100% MEAN EFFECTIVE PRESSURE AT CONTINUOUS POWER.kPa: ALTITUDE. m: SEA LEVEL MEAN EFFECTIVE PRESSURE AT MAXIMUM POWER. kpa: 1824,2 17 ENVIRONMENT CORROSIVE NON-CORROSIVE MAX.GAS EXHAUST % LOAD. O C: 7,2_ 18 CLASSIFICATION OF AREAS (ABNT) : GROUP : NON HAZARDOUS TEMPERATURE 75% LOAD. O C: 9,6 19 ROTATION: (VIEWED FROM COUPLING END) : CW CCW (CONT./MAX. POWER) 100% LOAD. O C: 4,7 20 CONSTRUCTION CHARACTERISTICS PERFORMANCE TEST (WITNESSED) : NO YES 21 TEST REPORT DELIVERY : NO YES 22 CASING SAE NUMBER: SAE 0 23 CYLINDER DIAMETER. mm : 170 QUANT.: 16 INJECTION SYSTEM 24 LAY-OUT : HORIZ. VERT. IN LINE IN V FUEL OIL TANK CAPACITY. l : BY CLIENT 25 PISTON STROKE. mm : 190 FUEL OIL TANK HEIGHT. m : BY CLIENT 26 MEDIUM PISTON VELOCITY. m/s: 11,4 FUEL FILTER - TYPE : DIS ELEM 27 DISPLACEMENT. cm 3 : INJECTION MFR.:CATERPILLAR 28 N o OF TIMES : 4 COMP. RATIO: 14:1 PUMP MODEL : TYPE : 29 MAXIMUM EXHAUST DROP PRESSURE ( p), kpa: 6.7 FEED NO YES. TYPE : PUMP 30 WEIGHTS. kg : MOTOR : 7825 SKID : 60 DRIVER : FRONT SIDE. mm : _1000 NATURAL TURBOCHARGED 32 NECESSARY BACK SIDE. mm : 1000 INLET WITH AFTERCOOLER WITHOUT AF. COOLER 33 AREA TO VERTICAL mm : 1000 MFR. : MODE: MAINTENANCE COMPRESSOR 34 RIGHT SIDE. mm : _1000 PRESSURE. kpa: FLOW. m 3 /s : 35 LEFT SIDE. mm :1000 SINGLE DOUBLE 36 PISTON MATERIAL : FILTER OIL FLOOD DRY 37 CYLINDER MATERIAL : BLOCK : CAST IRON HEAD : CAST IRON LINER : ALLOY 38 PAINTING 39 SPECIFICATION : MANUFACTURER SPECIFICATION 40 NOTES: 41 1) PAINTING SHALL BE CATERPILLAR STANDARD PROPER FOR OFFSHORE INSTALLATIONS. 42 2) FUEL OIL TANK CAPACITY TO CONTINUOUS RUNNING DURING 18 HOURS. 43 3) THIS DATA REFER ONLY MECHANICAL SOUND.

2 0 4 of 8 STARTING SYSTEM TRANSMISSION SYSTEM STARTING MANUAL PNEUMATIC MOTOR TRANSMISSION EXISTING TO BE FURNISHED 04 INSIDE CYLINDERS MOTOR DIRECT GEARBOX METHOD TYPE 05 ELECTRICAL BY BATTERY SOURCE, V: 24Vdc 06 BATTERY QUANT.: 4 TYPE: DRY MANUFACTURER: MODEL: 07 VOLTS:24Vdc PLATES. QUANT.: GEARBOX AGMA SERVICE FACTOR: EFFIC. 08 BATTERY ALTERNATOR: POWER, kw: SAE CASING N o : 09 CHARGER EXTERNAL SOURCE, VOLTS: 220Vac 10 DEVICE PHASES: 2 POWER, kw: 0.8 CLUTCH MANUFACTURER: MODEL: 11 PRESSURE kpag: FLOW, m 3 /s: SAE N o : 12 FILTER: NO YES TRANSMISSION NO YES 13 STARTING RESERVOIR: NO YES SHAFT MANUFACTURER: MODEL: 14 COMPRESSOR: NO YES FLEXIBLE 15 SYSTEM RESERVOIR VOLUM, l: COUPLING MANUFACTURER: TBD MODEL: MANUFACTURER: MODEL: LUBRICATION SYSTEM TORQUE 18 SAE CASING N o 19 LUBRICANT SINGLE DOUBLE CONVERTER RESERVOIR: NO YES 20 OIL FILTER RENEWABLE WASHABLE CAPACITY, 21 OIL TYPE: GEAR COOLING OIL CIRCUIT: NO YES 22 PUMP DRIVER: BY DIESEL ENGINE SHAFT GOVERNOR 23 PRE-LUBE NO YES 24 OIL PUMP DRIVER: AC ELECTRIC MOTOR MANUFACTURER: CAT MODEL: ADEM 3 25 LUBE OIL PRESSURE, kpag: 385,0 NEMA CLASS: IP54 TYPE: ELETRONIC 26 HEAT EXCHANGER: NO YES VELOCITY: CONSTANT VARIABLE 27 OIL TEMPERATURE DROP, o C: NA ADJUST: PNEUMATIC ELECTRONIC MANUAL 28 OIL PRESSURE DROP, kpa: _385 max 138 min RANGE, RPM: MAX.: 1800 MIN.: LUBE OIL VOLUM, l: 807 SIGNALRANGE, kpa / ma: 30 RECOMMENDED LUBE OIL: SAE 10W-40 / SAE 15W-30 SIGNAL FAILURE: STOP FEED MAINTAIN FEED 32 COOLING SYSTEM (fresh water / sea water) SPECIAL PARTS 33 COOLER WATER FLYWHEEL: STD. SPECIAL, TYPE: 34 RADIATOR: SINGLE DOUBLE INSULATED COLLECTOR: NO YES 35 HEAT EXCHANGER: NO YES, TYPE: PLATE EXHAUST MUFFLER: NO YES 36 FAN: BLOWER EXHAUST WITH INSULATED WITH SPARK ARRESTER 37 FAN PROTECTION SCREEN: NO YES PIPING: INSULATED WATER COOLED DRAIN 38 PRE-HEATING: NO YES FLEXIBLE CONNECTION: NO YES 39 AFTERCOOLER NO YES, TYPE: SHELL-TUBE BASEPLATE TYPE: 40 WATER PUMP DRIVER: BY ENGINE SHAFT NO MOTOR 41 MOTOR COOLING TYPE: CENTRIFUGAL YES MOTOR AND ACCESSORIES 42 WATER PUMP DRIVER: BY ENGINE SHAFT MOTOR, ACCES. AND DRIVEN EQUIPMENT 43 LOCAL PANEL PANEL 44 SAFETY (FIXED ON MOTOR) LOCAL REMOTE SYSTEM ALARM SHUTDOWN ALARM SHUTDOWN ALARM SHUTDOWN LOW LUBE OIL PRESSURE HIGH COOLING WATER TEMPERATURE OVERSPEED INLET BLOCK IN CYLINDERS LOW WATER COOLING LEVEL

3 0 5 of 8 LOCAL PANEL PANEL INSTRUMENTATION (4) 02 (FIXED ON MOTOR) LOCAL REMOTE 03 TACHOMETER DIGITAL RANGE:0 to 80,875 rpm 04 START MANOMETER RANGE: 05 LUBE OIL MANOMETER RANGE: 0 to 1000kPa 06 HOURMETER RANGE: 0 to ,75hr 07 VOLTMETER RANGE: 0 to 3212,75 v 08 AMMETER RANGE: 09 LUBE OIL THERMOMETER RANGE: -273 to 1734,96875 C 10 COOLING WATER THERMOMETER RANGE: -40 to 210 C 11 STARTING / STOPPING CONTROL 12 STOPPING CONTROL 13 PICK-UP CONTROL 14 DIESEL TANK LEVEL INDICATOR 15 LOW COOLANT WATER LEVEL GAUGE 16 DIESEL TANK "VENT" WITH FLAME ARRESTER 17 EXHAUST GAS TEMPERATURE RANGE: : -273 to 1734,96875 C 18 INLET PRESSURE BETWEEN FILTER AND ENGINE 19 LUBE OIL MAGNETIC PARTICLE DETECTOR SUPPLIED BY CLIENT ) DIESEL OIL SPECIFICATION: SPECIFIC GRAVITY: 843kg/m 3 VISCOSITY: 5,1cP SULPHUR CONCENTRATION: WATER: 0,1% FLASH POINT: 60 C NET HEATING VALUE: PARTICLE MAXIMUN SIZE: 10 micra NOTES GENERAL NOTE RANGE: 0 to 0kPa

4 0 6 of 8 SCOPEOF SUPPLY INCLUDED 04 DRIVEN EQUIPMENT 05 INSTRUMENTATION 06 CONTROL 07 JUNCTION BOX T0 INTERCONNECT INSTRUMENTATION 08 INSTRUMENTS PANEL (FIXED ON MOTOR) 09 CONTROL PANEL 10 INTERCONNECTING BETWEEN LOCAL INSTRUMENTATION AND LOCAL PANEL (FIXED ON MOTOR) 11 COMMON BASE FOR: DIESEL ENGINE DRIVEN EQUIPMENT GEARBOX 12 ANCHOR BOLTS AND PLATES 13 NON-VIBRATION SUPPORTS 14 COUPLING BETWEEN: DIESEL ENGINE AND DRIVEN EQUIPMENT 15 DIESEL ENGINE AND GEARBOX 16 GEARBOX AND DRIVEN EQUIPMENT 17 NON SPARKING GUARDS 18 FILTER 19 DISCHARGE MUFFLER (AISI 6 STEEL) 20 OIL / WATER AND GAS PIPING AT SKID LIMITS 21 OIL COOLER FAN COOLER 22 COOLING WATER SYSTEM WITH HEAT EXCHANGER 23 RADIATOR WITH FAN FAN SCREEN 24 PREFABRICATED PIPES BETWEEN RADIATOR AND ENGINE 25 PREFABRICATED PIPES BETWEEN ENGINE AND WATER COOLER 26 PREFABRICATED PIPES BETWEEN ENGINE AND OIL COOLER 27 GAS PREFABRICATED PIPES BETWEEN ENGINE AND MUFFLER 28 NOISE INSULATION 29 TURBOCHARGER 30 RESERVOIRS COMPRESSORS 32 BATTERY AND BATTERY CHARGER DEVICE 33 PIPING BETWEEN RESERVOIRS AND ENGINE 34 FUEL OIL TANK 35 PIPING BETWEEN FUEL OIL TANK AND ENGINE 36 TORSIONAL ANALYSIS 37 LOAD DIAGRAM 38 WRENCH AND SPECIAL TOOLS 39 TESTS CERTIFICATES 40 SPARE PARTS FOR COMMISSIONING, START-UP AND FOR 2 YEARS OPERATION

5 PICTOOIA!. YEW SCALf liou $iction SCAU 2;1 --.A.- IIOHI!o ENGI NE COOLANT IN " ll(l.t TIGtiTENNO SEQUENCE SCAt{ ll VIEW A A SEA WAHR OUT I Wlf H CUR IO S.U$ AW PI llaead(o SP'AtU.S IN locali$ 9 Uti 10. 9tt!l lltilhu 80l1$ I 1HRU e. If U.U[i- SII1U Ill lli(rui(iital $1[P$ 2 tili-o'li: t lf ll SAR$ UO nts :iro:i!. l QCATIOII$ 9 UD 10 l I.!ISU-ll Sr-'tUS, fjs)i[is.uf) iolls UliO LOCATICJS 9 AM10 Of ffio.t Ft.Aiff All) llmllef 4 IOfoot!l LTS IM toc1110lis IT!IRI 10 n PATUAN $.MO'Ih' tiol(a: Alf AlA 'Y.ll PA.it N0,8ll9S. J(I0 lltl'l( 0: AU nl!tl. IOt!llll r i(aiio MOl( (> i(rt:r TO $P((IAL I'.$UII.ICTI(IR AtH$ l5u UC IUI: SARS.UI) PillS AJ[ US!O II' locat U) )s t AN10 Of &C\ T T Hilll[JIIf$ SEQIJ(NC[ r A$S:(lIYl AND I)IS.ASSflmrOFPl ths ICIIJ.MER VPU.Si ti JIU TA.IIO JJO kpo 'fuel f:!iessir(