Making Tyre-Derived Materials a Commodity: A Comparison of the ASTM & CEN Standards
|
|
- Terence Houston
- 5 years ago
- Views:
Transcription
1 Making Tyre-Derived Materials a Commodity: A Comparison of the ASTM & CEN Standards MICHAEL BLUMENTHAL PRESIDENT, MARSHAY, INC. PRESENTED TO THE NEW ZEALAND SCRAP TYRE SUMMIT JUNE 3, 2015 AUCKLAND, NEW ZEALAND
2 ASTM International ASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence
3 Why are Standards Necessary? ASTM standards are recognized and accepted and can be used in court The US scrap tyre industry had a credibility problem in the early years: terms were being used without references Buyers were concerned about differences between what was promised and what was delivered Industry was facing many competitors whose materials had ASTM standards
4 ASTM Standards for Ground Rubber 2 standards for ground rubber were developed in was the first time that scrap tires were used as feed stock for ground rubber. Tire buffings, a byproduct of tire retreading, were the dominate material at that time. Developed as part of an effort by the RMA & NRC to get recycled materials onto the Chicago Board of Trade (CBOT). The effort failed, but the industry was able to standardize terminology and testing practices. Written by the F11 committee The two standards have not been updated since There was an effort to update the standards but there was very little input from the US ground rubber industry
5 ASTM Standards for Ground Rubber D : Standard Classification for Rubber Compounding Materials: Recycled Vulcanizate Particulate Rubber Terminology; Sizing of particles; Sampling procedures; Testing and Density How to run the tests to determine the size of the ground rubber D : Standard Classification for Rubber Compounding Materials: Determination of Particle Size Distribution of Recycled Vulcanizate Particular Rubber This standard was developed to establish the acceptable range of sizes in any size of ground rubber (10 mesh, 20 mesh, 30 mesh, etc.)
6 ASTM Standard on Tire Derived Fuel D : Standard Practice for Use of Scrap Tire-Derived Fuel Developed in 1996 Written at a time when TDF was becoming more refined: effort was to get rid of the term Nominal which was widely used but not a well defined term Last updated in 2012 Written by Michael Blumenthal, Mark Hope & Terry Gray
7 D Definitions Fuel analysis Sampling Testing procedures Particle sizing In 2016 the Standard should be updated to define smaller sized TDF
8 ASTM Standard for Asphalt Rubber Asphalt-Rubber as defined by ASTM D4, ASTM D6114 Asphalt-Rubber is a blend of asphalt cement, reclaimed tire rubber and certain additives, in which the rubber component is at least 15% by weight of the total blend and has reacted in the hot asphalt cement sufficiently to cause swelling of the rubber particles This is known as hot mix, Arizona mix or the McDonald Process Standard was developed between : The process to update this standard started in December 2014
9 D Terminology Testing procedures Particle distribution This standard cannot be changed to include other asphalt technologies which include ground tire rubber (warm mix, terminal blend). Warm mix will be performance graded (which AR is not) and terminal blending remains patented, which disallows it from having an ASTM standard
10 ASTM Standard: Tire Derived Aggregate D : Standard Practice for Use of Scrap Tires in Civil Engineering Applications Developed in 1996 Written, in part, as a result of the 2 internal heating episodes in Washington. Includes the guidelines for preventing hot spots. Since this document was written there have not been any other internal heating episodes Written by Dr. Dana Humphrey & Michael Blumenthal Updated in 2013
11 ASTM Standard: Tire-Derived Aggregate Definitions Particle size Material characteristics Construction practices Leachate Material properties MSDS
12 ASTM Std: Loose Fill Playground Rubber F Standard Specification for Loose-Fill Rubber for Use as a Playground Safety Surface under and around Playground Equipment: ASTM Volume Developed by Committee F08.63 and finalized in 2013, supported by efforts of ISRI & RMA Developed as a response to market challenges (competing materials have ASTM specs) and concerns about human/environmental health concerns The ASTM standard hasn t reduced concerns by some of the public but does address industrial concerns
13 ASTM Std: Loose Fill Playground Rubber Terminology Performance requirements Sampling Testing Size requirements Metal & fluff content There are many non-astm reports on human/health issues
14 ASTM Standard for Infill Rubber Being developed in the F08.65 subcommittee Currently has a ballot out for impact test which proposes lowering HIC & Gmax thresholds Discussions ongoing for new test method to measure infill depths Last meeting was May 2015 Benefit of an ASTM standard is to assist industry in standardizing material, have a bench-mark for comparison and compete against other infill materials
15 ASTM Standard for Rubber Infill Terminology Performance requirements Sampling Testing Size requirements Metal & fluff content
16 Conclusions The development of the ASTM standards for tire-derived removed an obstacle impeding the growth of markets and provides acceptable bench-marks ASTM standards gave legitimacy to the industry The ASTM standards place tire-derived materials on an equal level with competing materials The sale of ground rubber remains predominately an agreement between buyer & seller; ASTM standards provide a base line reference There remains the use of terms within the industry that are accepted and understood, but not consistent with the ASTM definitions: this still causes some confusion to outsiders Overall, the ASTM process has been a positive factor to our industry which should continue to be supported
17 CEN: The European Process The European Union has developed a series of standards for tire-derived materials: the standard setting organization is referred to as CEN CEN TS14243 characterizes the different materials derived from end of life tires in terms of dimensions (ELT cuts, shreds, chips, granulates and powders) and impurities (steel & textile) using (EU) harmonized methods of sampling and testing. The CEN TS standards were introduced in 2008 Work is on-going in CEN TC366 to validate and expand CEN TS14243 into an EU standard and to develop standards related to certain physical, composition characteristics of the materials produced from ELTs as well as to determine general properties of whole tires as required for further processing
18 Why Are EU Standards Being Updated? The lack of standardization in the tyre recovery field is a threat for the existing markets and a barrier for accessing new ones Without specific standards, tyre derived materials are often compared with other substitute materials, or "virgin materials", by means of improper testing methods that sometimes are not even suitable for rubber based goods The development of EU standards contributes to a significant increase of the quality level of tyre derived products while opening the market to new applications, promoting technology exchanges and access to know how
19 CEN has Established 4 Working Groups CEN/TC 366 / WG1 is working on the standard for ground rubber Determination of particle size for shreds (including sampling methods both laboratory and "in the field") Determination of particle size in powders, granulates and chips (including sampling methods both laboratory and "in the field") Determination of protruding wires in shreds Determination of free steel content for granulates and powder Determination of other impurities for granulates and powder
20 CEN/TC 366 WG2 Establishing standards for certain physical characteristics of the materials produced from ELTs Classification of materials produced from tyre. Terminology and characteristics Bulk density for shreds Bulk density for granulates and powder Bulk density for textile Bulk density for steel Determination of surface and geometry of granulates Determination of specific surface for granulates Determination of specific surface for powder Determination of hydraulic conductivity, permeability, settlement and compressibility for shreds Abrasion resistance of granulates
21 CEN/TC 366 WG3 Establishing standards for certain composition characteristics of the materials produced from ELTs Determination of NR/synthetic rubber in vulcanize material Determination of type of rubber (tyres and other scraped rubbers) Determination of non elastomeric content in rubber Determination of Carbon Black content in rubber Sampling method for elemental analysis Determination of moisture content for granulates, powder and textile fraction Determination of non metallic content for steel
22 CEN/TC 366 WG4 Standard on TDA Establishing standards for certain physical characteristics of whole tyres that are required in recovery and recycling processes. Quality criteria for the selection of whole tyres, for recovery and recycling processes. Characteristics of whole tyres for their use in Civil Engineering applications (porosity, crushing resistance).
23 CEN TC 343 Standard on TDF There is no one standard specific to ELT but some of then could be apply for determination of some characteristics of Tyre Derived Fuels. EN 15359:2011 EN 15400:2011 CEN/TS15401:2010 EN 15442:2011 CEN/TR 15591:2007 the 14C method Solid recovered fuels - Specifications and classes Solid recovered fuels - Determination of calorific value. Solid recovered fuels - Determination of bulk density Solid recovered fuels - Methods for sampling Solid recovered fuels - Determination of the biomass content based on
24 Infill & Playground Standards Infill (synthetic sport surfaces) CEN/TC 217Sport Surfaces / WG 10 Environmental Aspects: CEN TS Synthetic Sport System for Outdoor Leaching Test Playground Cover Activities on the field of Sports, playground and other recreational facilities and equipment are covered in the CEN TC 136 Main Standard related ELT material is EN 1177:2008 Impact attenuating playground surfacing - Determination of critical fall height
25 Implications Most of the CEN standards will look at the same characteristics as the ASTM standards Many of the CEN standards will conduct tests which have already been established by ASTM The CEN standards propose to analyze certain components of ELTs which significant variations (carbon black, synthetic rubber) CEN testing requirements could be expensive, which could actually be counterproductive to their goals The changing composition of tyres could present significant challenges to the CEN testing standards, rendering them almost useless If testing protocols are used by CEN are different than the ASTM testing protocols then the results, and subsequent standards will be different
26 ASTM Standards vs. CEN Standards Two sets of standards on the same material (tires) which are similar but have clear distinctions The new/revised CEN standards are expected by the end of 2015 ASTM standards do not present information on the chemical or physical properties of tires; this information is available through other sources. The CEN standards will include information not in the ASTM standards Coordination of these standards should take place so there aren t significant differences which could cause questions or difficulties within the international tire recycling industry
27 Contact Information Michael Blumenthal President Marshay, Inc. On the web: scraptireexpert.com
Global Overview: Legislative & Regulatory Environment. Scrap Tyre Management in the United States and the EU
Global Overview: Legislative & Regulatory Environment. Scrap Tyre Management in the United States and the EU MICHAEL BLUMENTHAL MARSHAY, INC. SCRAP TYRE SUMMIT, AUCKLAND, NEW ZEALAND, JUNE 2, 2015 Scrap
More informationDeveloping a Woodchip Heating Fuel Quality Standard for the U.S. Northeast Biomass Heating Expo April 27, 2017 Charlie Niebling, INRS
Developing a Woodchip Heating Fuel Quality Standard for the U.S. Northeast Biomass Heating Expo April 27, 2017 Charlie Niebling, INRS Presentation Background: Why a National Wood Chip Heating Fuel Quality
More informationStandards for solid biofuels - Status and prospects
Institut für Energetik und Umwelt Institute for Energy and Environment Research, Development, Services for - Energy - Environment Standards for solid biofuels - Status and prospects N. Becher, J. Witt,
More informationComparison of IG Testing Standard. IGMA Summer Meeting August 8, 2004
Comparison of IG Testing Standard IGMA Summer Meeting August 8, 2004 1 The Task Compare the new Harmonized standards to: Old ASTM stds. Canadian stds. CEN stds. (Europe) ISO std. (proposed) 2 The Standards
More informationFeedstock. Guide page 41. Home. Feedstock for the complete set of guidance please visit 1.
Feedstock Guidance on the issues which will affect the accessibility, security and suitability of waste materials as fuel for energy from waste processes 1.0 Introduction 2.0 Feedstock types 3.0 Fuel preparation
More informationRe-refined Oil Definition Review Proposed Revision. California Assembly Bill 1195 (AB1195)
Re-refined Oil Definition Review Proposed Revision California Assembly Bill 1195 (AB1195) History of Re-refined Oil Definition API was asked to provide a definition of a rerefined oil for AB 1195 The definition
More informationWhat s going on with European Specifications?
What s going on with European Specifications? Jean-Pascal PLANCHE - Total Sept. 15-16, 2003, Las Vegas eurobitume Outline Process of European standardization Current specifications Need for changes CEN/TC336
More informationWET GRIP TEST METHOD IMPROVEMENT for Passenger Car Tyres (C1) Overview of Tyre Industry / ISO activities. Ottawa
WET GRIP TEST METHOD IMPROVEMENT for Passenger Car Tyres (C1) Overview of Tyre Industry / ISO activities Ottawa June 11 th, 2017 1 CURRENT REGULATORY FRAMEWORK CURRENT WET GRIP PROCEDURE TECHNICAL PRINCIPLES
More informationNatural Gas for Transportation Codes & Standards Issues
Natural Gas for Transportation Codes & Standards Issues The safe and cost efficient development of the natural gas for transportation market in North America depends on having a robust system of codes
More informationAC Binder Characterization Containing Crumb Tire Rubber
AC Binder Characterization Containing Crumb Tire Rubber Gaylon L. Baumgardner Paragon Technical Services, Inc. LOUSIANA TRANSPORTATION RESEARCH CENTER SUSTAINABLE MATERIALS FOR PAVEMENT INFRASTRUCTURE:
More informationSession IV: Value chains, sustainability, standardisation Part 3: Standardisation
Session IV: Value chains, sustainability, standardisation Part 3: Standardisation Final Project Meeting, 06.05.2015 in Leipzig Eija Alakangas, VTT Hans Hartmann, TFZ Christoph Göbl, ofi Ute Wolfesberger-Schwabl,
More informationCONFERENCE ON AVIATION AND ALTERNATIVE FUELS
International Civil Aviation Organization CAAF/2-WP/17 7/09/2017 WORKING PAPER CONFERENCE ON AVIATION AND ALTERNATIVE FUELS Mexico City, Mexico, 11 to 13 October 2017 Agenda Item 1: Developments in research
More informationEUROPEAN COMMISSION ENTERPRISE AND INDUSTRY DIRECTORATE-GENERAL
EUROPEAN COMMISSION ENTERPRISE AND INDUSTRY DIRECTORATE-GENERAL Consumer Goods and EU Satellite navigation programmes Automotive industry Brussels, 08 April 2010 ENTR.F1/KS D(2010) European feed back to
More informationAlternative Jet Fuels
Alternative Jet Fuels FAA Overview: R&D Activities and Coordination Efforts Presented to: 6 th Annual Aviation & Marine Biofuels Summit By: Dr. James I. Hileman Office of Environment and Energy Date: March
More informationNORTH AMERICAN STANDARDS FOR LOW-VOLTAGE FUSES
127 NORTH AMERICAN STANDARDS FOR LOW-VOLTAGE FUSES Dale A. Hallerberg, P.E. Underwriters Laboratories Inc. September 25, 1995 1 General 1.1 Abstract The ability of fuse manufacturers to access larger markets
More informationBiofuels Standards Coordination Activities
Biofuels Standards Coordination Activities ITA Building Biofuels Infrastructure Conference June 19, 2007 Presented by Frances E. Schrotter Senior Vice President and Chief Operating Officer 1 Coordination
More informationASTM International ASTM Committee F-20 on Oil Spills and Hazardous Materials. 15 June 2010 OPRC Conference London, England
ASTM International ASTM Committee F-20 on Oil Spills and Hazardous Materials 15 June 2010 OPRC Conference London, England 1 What is ASTM International? A one-hundred-and-ten year old forum for the development
More informationASTM International 1
1 ASTM International ASTM INTERNATIONAL Organized in 1898 Independent, private sector, not-for-profit Provides a global forum for the development of voluntary, consensus standards and promotion of related
More informationCONFERENCE ON AVIATION AND ALTERNATIVE FUELS
International Civil Aviation Organization CAAF/09-WP/23 18/11/09 WORKING PAPER CONFERENCE ON AVIATION AND ALTERNATIVE FUELS Rio de Janeiro, Brazil, 16 to 18 November 2009 GLOBAL FRAMEWORK FOR AVIATION
More informationRECYCLABILITY EVALUATION PROTOCOL FOR PE FILMS
Phone : +32 2 742 96 82 Fax : +32 2 732 12 18 e-mail : recyclass@plasticsrecyclers.eu website: www.recyclass.eu RECYCLABILITY EVALUATION PROTOCOL FOR PE FILMS Standard Laboratory Practice Version 1.0 Published
More informationBiofuels - Global Situation, Concerns and the Future
Brazilian Association of Vegetable Oil Industries Biofuels - Global Situation, Concerns and the Future International Oilseed Producers Dialogue - IOPD Daniel Furlan Amaral Rio de Janeiro RJ Brazil June
More informationOhio s Scrap Tire Program
Rubber Pavements Association How to Cut Cost with Asphalt Rubber Workshop September 15, 2009 Ohio s Scrap Tire Program Presented by: Bob Large Ohio EPA Division of Solid and Infectious Waste Management
More informationFuel Related Definitions
Fuel Related Definitions ASH The solid residue left when combustible material is thoroughly burned or is oxidized by chemical means. The ash content of a fuel is the non combustible residue found in the
More informationAviation and Oil Depletion. Energy Institute 7 November 2006
Aviation and Oil Depletion Energy Institute 7 November 2006 By Christopher Smith Captain, BA Connect The Aviation Industry Aviation is one of the fastest growing industry sectors in the world Aviation
More informationStandardization of biomethane as automotive fuel
Standardization of biomethane as automotive fuel Jaime del Álamo Technical Manager NGVA Europe GGG Workshop. Development of Legislation, Injection and Trade Paris, 5 th March 2013 5 th March 2013 GGG Workshop.
More informationJet fuels and the road to future Jet fuels. IATA Operations Michel Baljet Assistant Director, Fuel Services
Jet fuels and the road to future Jet fuels 1 IATA Operations Michel Baljet Assistant Director, Fuel Services Jet fuels Aircraft need energy (MJ/kg) More energy per unit mass means: less fuel to be carried
More informationEuropean new pellets standards Case non-woody pellets, 4 May 2010, Lyon
European new pellets standards Case non-woody pellets, 4 May 2010, Lyon Eija Alakangas, VTT Convenor of Fuel specification and classes, WG2 of CEN/TC 335 http://www.eubionet.net Multipart standard EN14961
More informationThe New EMC Requirements of Electric Cars
The New EMC Requirements of Electric Cars Author : Michael Koffink and Roland Gubisch 05/24/2009 Refinements are needed for better correlation between chip-level or module-level measurements and whole
More informationWET GRIP TEST METHOD IMPROVEMENT for Passenger Car Tyres (C1) GRBP 68 th session
Transmitted by the expert from ETRTO Informal document GRB-68-15 (68 th GRB, 12-14 September 2018, agenda item 6) WET GRIP TEST METHOD IMPROVEMENT for Passenger Car Tyres (C1) Overview of Tyre Industry
More informationTIER 3 MOTOR VEHICLE FUEL STANDARDS FOR DENATURED FUEL ETHANOL
2016 TIER 3 MOTOR VEHICLE FUEL STANDARDS FOR DENATURED FUEL ETHANOL This document was prepared by the Renewable Fuels Association (RFA). The information, though believed to be accurate at the time of publication,
More informationGLOBAL REGISTRY. Addendum. Global technical regulation No. 5
23 January 2007 GLOBAL REGISTRY Created on 18 November 2004, pursuant to Article 6 of the AGREEMENT CONCERNING THE ESTABLISHING OF GLOBAL TECHNICAL REGULATIONS FOR WHEELED VEHICLES, EQUIPMENT AND PARTS
More informationASTM International Committee D02 on Petroleum Products and Lubricants February NBC, Orlando, FL
ASTM International Committee D02 on Petroleum Products and Lubricants February 2008 NBC, Orlando, FL 1 Presentation Provide an overview of ASTM International and ASTM s standardization concepts Introduce
More informationWood Chip Heating Fuel Quality Standard for the U.S.
Wood Chip Heating Fuel Quality Standard for the U.S. Biomass Thermal Energy Council Webinar June 6th, 2018 Adam Sherman Jean Walsh Jim Dooley Quick Notes Two Audio Options: Streaming Audio and Dial-In.
More informationDO YOU WANT TO TURN WASTE TO FUEL AND PROFIT?
WASTE TO FUEL Some see a problem, others see an opportunity. DO YOU WANT TO TURN WASTE TO FUEL AND PROFIT? The best way to do that is to get a complete TYRANNOSAURUS plant from BMH Technology. You will
More informationANNEX MOTOR VEHICLES AND MOTOR VEHICLES' PARTS. Article 1. General Provisions
ANNEX MOTOR VEHICLES AND MOTOR VEHICLES' PARTS Article 1 General Provisions 1. This Annex shall apply to motor vehicles in UNECE vehicle regulations' category M1 as well as parts and equipment regulated
More informationQ&A ON EMISSIONS TESTING
Q&A ON EMISSIONS TESTING 1. How does ACEA react to the VW situation?... 1 2. How does the current lab test work?... 1 3. Why are there differences between the lab tests and real-world emissions?... 3 4.
More informationAIR POLLUTION AND ENERGY EFFICIENCY. Update on the proposal for "A transparent and reliable hull and propeller performance standard"
E MARINE ENVIRONMENT PROTECTION COMMITTEE 64th session Agenda item 4 MEPC 64/INF.23 27 July 2012 ENGLISH ONLY AIR POLLUTION AND ENERGY EFFICIENCY Update on the proposal for "A transparent and reliable
More informationRenewable Fuels Association One Massachusetts Ave. NW Suite 820 Washington, DC Telephone: (202) Fax: (202)
Guidelines for Establishing Ethanol Plant Quality Assurance and Quality Control Programs Renewable Fuels Association One Massachusetts Ave. NW Suite 820 Washington, DC 20001 Telephone: (202) 289-3835 Fax:
More informationPFI Standard Specification for Residential/Commercial Densified Fuel 18-June-2008
Pellet Fuel Institute (PFI) Standard Specification for Residential/Commercial Densified Fuel 1. Scope 1.1 This specification is applicable for the determination of fuel quality grade for Residential or
More informationThis presentation focuses on Biodiesel, scientifically called FAME (Fatty Acid Methyl Ester); a fuel different in either perspective.
Today, we know a huge variety of so-called alternative fuels which are usually regarded as biofuels, even though this is not always true. Alternative fuels can replace fossil fuels in existing combustion
More informationEuropean Tyre and Rim Technical Organisation RETREADED TYRES IMPACT OF CASING AND RETREADING PROCESS ON RETREADED TYRES LABELLED PERFORMANCES
European Tyre and Rim Technical Organisation RETREADED TYRES IMPACT OF CASING AND RETREADING PROCESS ON RETREADED TYRES LABELLED PERFORMANCES Content 1. Executive summary... 4 2. Retreaded tyres: reminder
More informationSAE Aerospace Standards Summit 2017 The role of Industry Standards in EASA regulatory framework
SAE Aerospace Standards Summit 2017 The role of Industry Standards in EASA regulatory framework Rachel Daeschler, Deputy Strategy and Safety Management Director Pascal Medal Chief Engineer EASA TE.GEN.00409-001
More informationTHE EU AND PALM OIL: WHAT S GOING ON?
THE EU AND PALM OIL: WHAT S GOING ON? RSPO Roundtable 9 Kota Kinabalu, 24 November 2011 Nina Činkole Delegation of the European Union to Malaysia 1 PRESENTATION OUTLINE EU Context & Policy background Biofuels:
More informationTechnical Committee Motor Vehicles 15 September RDE 3 discussion
Technical Committee Motor Vehicles 15 September 2016 RDE 3 discussion 1 RDE-LDV working group meetings on RDE-3 in 2016 23 January (launch) 20 April 17, 18 May 1 June (cold start web) 2 June (hybrid web)
More informationGC MERGE OF LIGHT ENDS WITH ASTM D7169 BOILING POINT DISTRIBUTION
GC MERGE OF LIGHT ENDS WITH ASTM D7169 BOILING POINT DISTRIBUTION Crude Oil Quality Association St. Louis, MO June 8, 2017 Arden Strycker, Ph.D. SGS North America Providing Solutions Across the Value Chain
More informationEfforts to Align US/EU/ISO Toy Standards for Cadmium
2011/SOM1/SCSC/CON1/005 Session 3 Efforts to Align US/EU/ISO Toy Standards for Cadmium Submitted by: Toy Industry Association (TIA) 6 th Conference on Good Regulatory Practice Washington, D.C., United
More informationEuropean Regulations for Formaldehyde
European Regulations for Formaldehyde Harald Schwab, Rainer Marutzky, Bettina Meyer Fraunhofer Institute for Wood Research Wilhelm-Klauditz-Institut Braunschweig / Germany Topics of this presentation Introduction
More informationASTM Consensus Standards The Latest in Packaging Testing. Presented by: Dhuanne Dodrill President Rollprint Packaging Products, Inc.
ASTM Consensus Standards The Latest in Packaging Testing Presented by: Dhuanne Dodrill President Rollprint Packaging Products, Inc. ASTM Overview Established in 1898 Voluntary, Full-Consensus Standards
More informationOverview of the Biofuels Market. Timothy McCoy SCB Commodity Brokers
Overview of the Biofuels Market Timothy McCoy SCB Commodity Brokers Background Trinity College Graduate 2011 Civil, Structural & Environmental Engineering Trainee project manager with StructureTone in
More informationCreating intelligent technologies for land and water based industries
Creating intelligent technologies for land and water based industries Summary ISO standards ASABE and ASTM standards (US) Protocols What is missing for helping assure our data from one country can be considered
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD IEC 62281 Edition 2.0 2012-12 colour inside Safety of primary and secondary lithium cells and batteries during transport INTERNATIONAL ELECTROTECHNICAL COMMISSION PRICE CODE T ICS
More informationOverview of FAA Alternative Jet Fuel Efforts. Aaron Wilkins Senior Representative, UAE Federal Aviation Administration
Overview of FAA Alternative Jet Fuel Efforts Aaron Wilkins Senior Representative, UAE Federal Aviation Administration Aviation Environmental Challenges NOISE AIR QUALITY WATER QUALITY ENERGY GLOBAL CLIMATE
More informationDigital Copper Corrosion Measurement Vs. Visual Rating _ Incorporating New Technologies To Method Development
Digital Copper Corrosion Measurement Vs. Visual _ Incorporating New Technologies To Method Development Aaron Mendez Ph.D. and Juan Ayala Ayalytical Instruments Inc. 2787 W Fulton St, Chicago, IL 60612
More informationBrief on the PCFV Used Vehicle Working Group. Partnership for Clean Fuels and Vehicles (PCFV)
Brief on the PCFV Used Vehicle Working Group Partnership for Clean Fuels and Vehicles (PCFV) Henry Kamau Establishment of the Used Vehicles Working Group The Partnership for Clean Fuels and Vehicles (PCFV)
More informationGEODE Report: Flexibility in Tomorrow s Energy System DSOs approach
1 GEODE Report: Flexibility in Tomorrow s Energy System DSOs approach Report was prepared by Working Group Smart Grids of GEODE GEODE Spring Seminar, Brussels, 13th of May 2014 Hans Taus, Wiener Netze
More informationREGULATION No. 94 (Frontal collision) Proposal for draft amendments. Proposal submitted by France
Informal Document No. GRSP-42-31 (42nd GRSP, 11-14 December 2007, agenda item 17(b)) REGULATION No. 94 (Frontal collision) Proposal for draft amendments Proposal submitted by France 1 Aim The expert from
More informationTHE PRACTICE OF MANUFACTURING DURISOL NOISE BARRIER PANELS
THE PRACTICE OF MANUFACTURING DURISOL NOISE BARRIER PANELS MARTIN, ROHN; HUCHENG, QI Durisol, a Division of Armtec Limited Partnership 51 Arthur Street South, Mitchell, Ontario, Canada N0K 1N0 ABSTRACT
More informationHigh Speed Passenger Rail Interoperability in North America
High Speed Passenger Rail Interoperability in North America APTA Rail Conference - Boston Thomas Peacock Larry D. Kelterborn June15, 2011 Discussion Topics The New Transportation Vision Meaning of Interoperability
More informationOhio s Used Oil Regulations for Generators
Ohio s Used Oil Regulations for Generators Dan Sowry Office of Compliance Assistance & Pollution Prevention January 29 th, 2013 What we will cover Definition Generator responsibilities On-site management
More informationIEEE* American National Standards
IEEE* American National Standards T. Basso, NREL** and IEEE SCC21 Secretary; M. Coddington, NREL; P. McNutt, NREL; and R. DeBlasio, NREL and IEEE SCC 21 Chair and IEEE Smart Grid POC Solar America Board
More informationHow to Achieve a Successful Molded Gear Transmission
How to Achieve a Successful Molded Gear Transmission Rod Kleiss Figure 1 A molding insert tool alongside the molded gear and the gear cavitiy. Molded plastic gears have very little in common with machined
More informationLabelling Smart Roads DISCUSSION PAPER 4/2015
DISCUSSION PAPER 4/2015 December 2015 TABLE OF CONTENTS 1. Introduction... 3 2. The Smart Roads of the Future... 3 3. : Sustainability of road infrastructure... 4 4. : Sustainability in mobility management
More informationDOWNLOAD OR READ : RUBBER COMPANIES IN THE NETHERLAND EAST INDIES SCHOLARS CHOICE EDITION PDF EBOOK EPUB MOBI
DOWNLOAD OR READ : RUBBER COMPANIES IN THE NETHERLAND EAST INDIES SCHOLARS CHOICE EDITION PDF EBOOK EPUB MOBI Page 1 Page 2 rubber companies in the netherland east indies scholars choice edition rubber
More informationEconomic and Social Council
United Nations Economic and Social Council ECE/TRANS/WP.29/GRRF/2013/33 Distr.: General 5 July 2013 Original: English Economic Commission for Europe Inland Transport Committee World Forum for Harmonization
More informationEuropean and International Standards
International Biofuels Conference (5-6 July 2007) European and International Standards Ernst-Peter Ziethen CEN Vice-President Technical CEN European Committee for Standardization www.cenorm.eu 30 National
More informationRSB List of Documents and references
Type of document: Reference Document Date: 20 March 2017 RSB List of Documents and references RSB reference code: [RSB-DOC-10-001] Published by the Roundtable on Sustainable Biomaterials. This publication
More informationAddressing the API Licensing Fear Factor
Addressing the API Licensing Fear Factor Overview There are motor oil consumers who have a fear of using non-api certified motor oils, i.e. motor oils that do not have the API donut certification. The
More information2011 NDIA GROUND VEHICLE SYSTEMS ENGINEERING AND TECHNOLOGY SYMPOSIUM POWER AND MOBILITY (P&M) MINI-SYMPOSIUM AUGUST 9-11 DEARBORN, MICHIGAN
211 NDIA GROUND VEHICLE SYSTEMS ENGINEERING AND TECHNOLOGY SYMPOSIUM POWER AND MOBILITY (P&M) MINI-SYMPOSIUM AUGUST 9-11 DEARBORN, MICHIGAN Electrode material enhancements for lead-acid batteries Dr. William
More informationClaus unit Tail gas treatment catalysts
Claus unit Tail gas treatment catalysts The TK catalyst family Figure 1: Sulphur recovery flow scheme Tail gas treatment catalysts In the refining industry today, sulphur recovery is an extremely important
More informationDevelopment of Gearboxes for Conveyors in Poultry Processing Facilities by Technicon. November 6, 2018
Development of Gearboxes for Conveyors in Poultry Processing Facilities by Technicon November 6, 2018 1 Poultry Processing Facilities Have Many Gearboxes Driving Conveyors If you see poultry moving with
More informationRSB ROUNDTABLE ON SUSTAINABLE BIOMATERIALS RSB List of Documents and references. 18 January RSB reference code: RSB-DOC
RSB ROUNDTABLE ON SUSTAINABLE BIOMATERIALS RSB List of Documents and references 18 January 2019 RSB reference code: RSB-DOC-10-001 Published by the Roundtable on Sustainable Biomaterials. This publication
More informationENERGY STAR Program Requirements for Single Voltage External Ac-Dc and Ac-Ac Power Supplies. Eligibility Criteria.
ENERGY STAR Program Requirements for Single Voltage External Ac-Dc and Ac-Ac Power Supplies Eligibility Criteria Table of Contents Section 1: Definitions 2 Section 2: Qualifying Products 3 Section 3: Energy-Efficiency
More informationVALVOLINE HYDRAULIC OILS PEOPLE WHO KNOW USE VALVOLINE
VALVOLINE HYDRAULIC OILS PEOPLE WHO KNOW USE VALVOLINE VALVOLINE I HYDRAULIC OILS TOGETHER, STRONGER! First brand - First in innovation Dr. John Ellis created the petroleum industry s first brand in 1866.
More informationBaghouse Conversion to Pleated Filter Elements From Standard Bag and Cage Setup - Cost Benefit Analysis
Baghouse Conversion to Pleated Filter Elements From Standard Bag and Cage Setup - Cost Benefit Analysis Prepared By Dominick DalSanto Table of Contents Summery 3 Introduction 1 What is a Pleated Baghouse
More informationMOBILITY STRATEGY AND APPROACH OF IEC. Dr. Bernhard Thies German National Committee of the IEC
MOBILITY STRATEGY AND APPROACH OF IEC Dr. Bernhard Thies German National Committee of the IEC Connecting an Electric Vehicle to the Grid (Smart) Grid Power generation Charging station Battery electric
More informationREVISED RECOMMENDATION FOR MATERIAL DATA SHEETS (MSDS) FOR MARPOL ANNEX I TYPE OIL AS CARGO IN BULK AND MARINE FUEL OIL
INTERNATIONAL SHIP CLASSIFICATION 10 Anson Road, #25-01 International Plaza Singapore 079903 Tel: +65 6225 2565 Fax: +65 6225 2265 Email: info@isclass.com Website: www.isclass.com To : All Office From
More informationRequest for Assistance (RFA)
Request for Assistance (RFA) RFA #: FY15-Consultant Canvas Development - 2 Issued on: July 13, 2017 For: Development services to support the implementation of an open-source instance of the Canvas LMS
More informationEuropean biomethane standards for grid injection and vehicle fuel use
European biomethane standards for grid injection and vehicle fuel use Biosurf Workshop 5 December 2017, Amsterdam Dr Arthur Wellinger European Biogas Association CEN TC 408 In the framework of Biosurf,
More information1 COPYRIGHT 2018, LUBES N GREASES MAGAZINE. REPRODUCED WITH PERMISSION FROM THE MAY 2018 ISSUE
1 COPYRIGHT 2018, LUBES N GREASES MAGAZINE. REPRODUCED WITH PERMISSION FROM THE MAY 2018 ISSUE Sulfur Cap Looms for Marine Lubes The marine industry is sailing toward a period of unprecedented change.
More informationCITY OF MINNEAPOLIS GREEN FLEET POLICY
CITY OF MINNEAPOLIS GREEN FLEET POLICY TABLE OF CONTENTS I. Introduction Purpose & Objectives Oversight: The Green Fleet Team II. Establishing a Baseline for Inventory III. Implementation Strategies Optimize
More informationThe Role of DSO as Facilitator of the Electricity Markets in Macedonia. Key aspects and considerations
The Role of DSO as Facilitator of the Electricity Markets in Macedonia Key aspects and considerations 30 th of May, 2017 Renewable Energy Production in Macedonia (1/5) Supportive Measures Installed capacity
More informationFRESH SOLUTIONS FOR PAINTS AND COATINGS
FRESH SOLUTIONS FOR PAINTS AND COATINGS SHELL GTL SOLVENTS ARE NEXT GENERATION, HIGH PURITY PARAFFINIC FLUIDS BASED ON INNOVATIVE GAS-TO-LIQUIDS TECHNOLOGY. Their unique synthetic composition, with low
More informationDME as LPG Blendstock: A Disruptive or Sustaining Innovation?
DME as LPG Blendstock: A Disruptive or Sustaining Innovation? Dr. Ron Sills, DME and Alternative Energy Consultant Former BP Gas Conversion Network Leader Purvin & Gertz International LPG Seminar The Woodlands,
More informationSynthesis of Optimal Batch Distillation Sequences
Presented at the World Batch Forum North American Conference Woodcliff Lake, NJ April 7-10, 2002 107 S. Southgate Drive Chandler, Arizona 85226-3222 480-893-8803 Fax 480-893-7775 E-mail: info@wbf.org www.wbf.org
More informationMarch, Status of U.S. Electric Drive Energy Learning Network Webinar. United States Department of Energy
Status of U.S. Electric Drive Energy Learning Network Webinar United States Department of Energy March, 2011 Vehicle Technologies Program Linda Bluestein We are Highly Dependent on Oil Natural Gas 3% Natural
More informationRailway noise control in urban areas. Jakob Oertli, SBB Infrastructure, Noise Abatement; Chair UIC Noise Groups
Railway noise control in urban areas Jakob Oertli, SBB Infrastructure, Noise Abatement; Chair UIC Noise Groups Contents. 1. Railway noise situation 2. Policy and legislation 3. Noise reduction technology
More information- 770 l. 770L Trash Bins 4 Wheeled Category
- 770 l 770L Trash Bins 4 Wheeled Category - 770l Features and Data Sheet Design McClean offers a wide range of mobile garbage bins (MGB) and waste containers, fitted for ergonomic design and robust features
More information-1100l. 1100L Trash Bins 4 Wheeled Category
-1100l 1100L Trash Bins 4 Wheeled Category - 1100l FEATURES AND DATA SHEET DESIGN McClean offers a wide range of mobile garbage bins (MGB) and waste containers, fitted for ergonomic design and robust features
More informationPART XV Metering Systems SECTION 2 GUIDE TO GAS METERING SYSTEMS
THE INSTITUTE OF PETROLEUM PETROLEUM MEASUREMENT MANUAL PART XV Metering Systems SECTION 2 GUIDE TO GAS METERING SYSTEMS THE INSTITUTE OF PETROLEUM PETROLEUM MEASUREMENT MANUAL PART XV Metering Systems
More informationDecember 2009, March 2010
March 2013 20 July 2013 21 March 2013 22 December 2009 23 December 2009, March 2010 24 March 2012 25 December 2012 26 March 2011 27 December 2013 28 November 2013 29 September 2011 30 January 2014 31 July
More informationPresentation of the European Electricity Grid Initiative
Presentation of the European Electricity Grid Initiative Contractors Meeting Brussels 25th September 2009 1 Outline Electricity Network Scenario European Electricity Grids Initiative DSOs Smart Grids Model
More informationAdams-EDEM Co-simulation for Predicting Military Vehicle Mobility on Soft Soil
Adams-EDEM Co-simulation for Predicting Military Vehicle Mobility on Soft Soil By Brian Edwards, Vehicle Dynamics Group, Pratt and Miller Engineering, USA 22 Engineering Reality Magazine Multibody Dynamics
More informationAccommodating High Levels of Variable Generation. EPRI Managing Complexity for Safety and Reliability September 14-15, 15, 2009
Accommodating High Levels of Variable Generation EPRI Managing Complexity for Safety and Reliability September 14-15, 15, 2009 Agenda About NERC About the Integration of Variable Generation Task Force
More informationUL ALTERNATIVE FUELS & STANDARDS UPDATE
UL ALTERNATIVE FUELS & STANDARDS UPDATE - 2008 Presented at the 2008 EPA UST Annual Tank Conference ROLAND RIEGEL - PRIMARY DESIGNATED ENGINEER Flammable Liquids Containment Products REVIEW of PREVIOUS
More informationDevelopment of long life structural asphalt
Build something great Development of long life structural asphalt Trevor Distin Sustainability opportunities for the asphalt industry Reusing RAP Preservation of raw materials bitumen & aggregates However
More informationDI Manfred Haider arsenal research. WG leader of PIARC TC 4.2 WG B Road Traffic Noise , Geneva Presentation to UN ECE/TRANS/ WP.
1 World Road Association (PIARC) Established in 1909 Non-political, non-profit organization Development of global road community 2 Mission Lead international forum Disseminate best practice Promote efficient
More informationEurailspeed Parallel Session F.1. Michael Schemmer Chairman UNIFE WG Transport and Environment Bombardier Transportation
Eurailspeed Parallel Session F.1 Michael Schemmer Chairman UNIFE WG Transport and Environment Bombardier Transportation 1 High-speed rail, the environmentally friendly solution for mobility Dr. Michael
More informationResults... Survey on Mechanical Issues Related to Biodiesel Blending
Results... Survey on Mechanical Issues Related to Biodiesel Blending Fall 2016 Prepared by: Dr. Thomas Butcher National Oilheat Research Alliance March 2017 NORA Report 17-1 National Oilheat Research Alliance
More informationPre-normative research on resistance to mechanical impact of composite overwrapped pressure vessels. Dr. Fabien Nony CEA
Pre-normative research on resistance to mechanical impact of composite overwrapped pressure vessels Dr. Fabien Nony CEA http://hypactor.eu/ Email Coordinator: fabien.nony@cea.fr Programme Review Days 2017
More informationSchedule of Accreditation issued by United Kingdom Accreditation Service 2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK
2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK The Old School Stillhouse Lane Bedminster BS3 4EB Contact: Dr Dimitris Xirouchakis Tel: +44 (0)117-9471000 Fax: +44 (0)117-9471004 E-Mail:
More information