Hydroflow Distributors (AUS) Pty Ltd PRODUCT APPRAISAL REPORT PA1710

Transcription

1 WSAA Product Appraisal Hydroflow Distributors (AUS) Pty Ltd PRODUCT APPRAISAL REPORT PA1710 PE100 Electrofusion and Spigot Fittings AS/NZS 4129:2008 Fittings for polyethylene (PE) pipes for pressure applications Publication Date: 5 October 2017

2 WSAA Product Appraisal Document History The following information indicates the changes made to this document. Date Version File Location 25/8/2017 Peer Review Draft 5/10/2017 Publication Version U:\PP1 Industry Performance and Regulation\PP1-012 Product Appraisals\Civil Asset Infrastructure\2017\PA 1710 Hydroflow Distributors Aust Ptd Ltd Plastatlia PE Fittings\PA 1710_Hydroflow_Electofusion and spigot fittings.docx U:\PP1 Industry Performance and Regulation\PP1-012 Product Appraisals\Civil Asset Infrastructure\2017\PA 1710 Hydroflow Distributors Aust Ptd Ltd Plastatlia PE Fittings\PA 1710_Hydroflow_Electofusion and spigot fittings final.docx Peer Reviewers Name/Title Organisation Date Product Appraisal Technical Advisory Group WSAA 2/10/2017 Expert Panel WSAA 2/10/2017 Alan Whittle, WSAA Contractor WSAA 25/8/2017 Carl Radford, Product Appraisal Manager WSAA 25/8/2017

3 WSAA Product Appraisal Overview of WSAA The Water Services Association of Australia (WSAA) is the peak industry body representing the urban water industry. Our members provide water and sewerage services to over 20 million customers in Australia and New Zealand and many of Australia's largest industrial and commercial enterprises. Based around our vision of 'customer driven, enriching life', WSAA facilitates collaboration, knowledge sharing, networking and cooperation within the urban water industry. We are proud of the collegiate attitude of our members which has led to industry-wide approaches to national water issues. WSAA can demonstrate success in the standardisation of industry performance monitoring and benchmarking, as well as many research outcomes of national significance. The WSAA Executive retains strong links with policy makers and legislative bodies and their influencers, to monitor emerging issues of importance to the urban water industry. WSAA was formed in 1995 as a non-profit organisation to foster the exchange of information between industry, government and the community, and to promote sustainable water resource management. The urban water industry is committed to anchoring its services to customers' values, and to enrich communities where water services have broad economic, environmental and social values. In line with this our main activities focus on four areas: 1. influencing national and state policies on the provision of urban water services and sustainable water resource management 2. promoting debate on environmentally sustainable development and management of water resources and the community health requirements of public water supplies 3. improving industry performance and establishing benchmarks and industry leading practices for water service processes; and 4. fostering the exchange of information on education, training, research, water and wastewater management and treatment and other matters of common interest. Copyright This document is copyrighted. Apart from any use as permitted under the Copyright Act 1968, no part of this document may be reproduced or transmitted in any form or by any means, electronically or mechanical, for any purpose, without the express written permission of Water Services Association of Australia Limited. Copyright 2017 by WATER SERVICES ASSOCIATION of Australia Limited All rights reserved.

4 WSAA Product Appraisal CONTENTS 1 EXECUTIVE SUMMARY Recommendations THE APPLICANT The Supplier The Manufacturer THE PRODUCT SCOPE OF THE APPRAISAL APPRAISAL CRITERIA Quality Assurance Requirements Performance Requirements COMPLIANCE WITH APPRAISAL CRITERIA Compliance with Quality Assurance Requirements Compliance with Performance Requirements FITTING INSTRUCTIONS, TRAINING AND INSTALLATION PRODUCT MARKING PACKAGING AND TRANSPORTATION PRODUCT WARRANTY WATER AGENCY EXPERIENCE WITH THE PRODUCT OR FIELD TESTING REPORT DISCUSSION OUTCOMES OF EXPERT PANEL PRODUCT REVIEW LIFE EXPECTANCY FUTURE WORKS DISCLAIMER Issue of Report Limits on Reliance on Information and Recommendations Disclaimer of liability Intellectual Property and other rights Need for independent assessment No Updating No Warranty APPENDIX A - TECHNICAL LITERATURE APPENDIX B - QUALITY CERTIFICATIONS APPENDIX C - WSA PRODUCT SPECIFICATION APPENDIX D - SUPPLIER CONTACTS APPENDIX E - NATA LABORATORY TEST RESULTS APPENDIX F - LABORATORY TEST RESULTS APPPENDIX G PRODUCT RANGE APPENDIX H MARKING DETAILS... 84

5 WSAA Product Appraisal EXECUTIVE SUMMARY Plastitalia supplies PLAST polyethylene fittings to the international market. It is based in Sicily and the comprehensive range of products is available globally through licensees and distributors. The products are distributed in Australia by Hydroflow. This appraisal applies to electrofusion fittings comprising couplers, elbows, tees, reducers, endcaps and saddles together with spigot fittings comprising tees, elbows, junctions and reducers. Saddles are supplied with NBR seals. Plastitalia electrofusion and spigot fittings are manufactured from black PE100 compound. The PE100 materials used are BorSafe HE3490-LS-H, BorSafe HE3490-IM, Sabic Vestolen A6060R 1000 or Sabic Vestolen A RELY 5922R The electrofusion range is produced in SDR11. Note that SDR11 pipe made with PE100 equates to PN 16 for water applications. Some EF couplings are also produced in other SDRs. The spigot fittings are available in SDR9, SDR11 and SDR17, equating to PN 20, PN 16 and PN 10 respectively. The manufacturing site has a management system third party certified to ISO The company also has a third party certified environmental management system to ISO and occupational health and safety system to ISO Notes: 1 -The following Plastitalia fittings are not included in this appraisal: a. Transition fittings metal to polyethylene. b. Fabricated fittings. A summary of the appraised product range is shown in Section 3 below. The full Product Certification Schedules that include the appraised product range are available at the members only section of the WSAA Product Appraisal Technical Advisory Groups website in the Products Guide and the Plastitalia web site The appraisal concludes that: The nominated Plastitalia fittings are fit for purpose and suitable for use in water supply and sewer gravity, pressure and vacuum systems. The Plastitalia electrofusion and spigot fittings are suitable for use with PE pipe conforming to AS/NZS ISO Type 5 product certification of the appraised range of Plastitalia electrofusion and spigot fittings has been adequately addressed to the satisfaction of WSAA Appraisal Network. Electrofusion and butt fusion techniques are established practices in polyethylene pipeline installations. However, it is important that installers and supervisors are trained and experienced. In particular, they need to be experienced in the installation of the diameter range of interest to the Water Agency. Tapping tees are supplied with NBR seals complying with EN This Standard has been cloned as AS Elastomeric seals Material requirements for pipe joint seals used in water and drainage applications Part 1: Vulcanized rubber. 1.1 Recommendations It is recommended that WSAA members, subject to any specific requirements of the member, accept or authorise the Plastitalia range of PLAST electrofusion and spigot fittings as detailed in this report for use in applications including water supply, gravity, vacuum and pressure sewers provided only appropriately trained and qualified operators are permitted to perform the welding and the design, installation, acceptance testing and operation are in accordance with the appropriate WSAA Codes, including WSAA member integrated Codes, nominated Standards and manufacturer s requirements.

6 WSAA Product Appraisal THE APPLICANT Hydroflow Distributors (Aus) Pty Ltd. 2.1 The Supplier Hydroflow Distributors (Aus) Pty Ltd. Hydroflow Distributors Australia was established in 2013 and operates out of a distribution centre located at Altona, Melbourne. The company s stated objective is to distribute leading industrial brands selected on the basis of product innovation and quality whilst providing quality, industry leading, technical support. The focus is on water and gas and on sourcing the world s most innovative products for safe control, quality and conservation. Hydroflow is also the exclusive distributor of the Watts/Ames range of backflow devices. Watts is part of the Watts Water Technologies family with operations in North America, Europe and Asia. Hydroflow provides technical specialists have extensive knowledge of the Watts backflow range and backflow issues in general. Hydroflow supplies product into the HVAC, Fire Protection and infrastructure markets with brands such as Victaulic and Erico. In addition Hydroflow Australia stocks the Italian SAB range of metric pipe fittings, Bugatti ball valve range and Plastitalia electrofusion fittings. 2.2 The Manufacturer Plastitalia S.p.A In 1975, N. Lenzo, commenced the business Eurocondotte on the eastern coast of Sicily utilising his family s experience of the construction and operation of water supply facilities. In 1988 the production division of Plastitalia was created and progressively equipped with modern production equipment in order to make an increasingly specialized range of products. The growth of Plastitalia was rapid, prompting the creation of a separate company Plastitalia S.r.l. (similar to a Limited Liability Company) in Since that time Plastitalia has further established itself on the international market. For example, on January 1, 1995, Plastitalia products became certified by the Italian national plastics institute - Istituto Italiano dei Plastici S.r.l. (IIP-UNI) to strengthen consumer confidence, distinguish itself from competitors, and increase brand recognition. Every new product is made in accordance with the certification requirements of IIP-UNI, covering the entire range of production. In order to satisfy clients, Plastitalia works to ensure consistent quality of product and services by obtaining the latest certifications from major institutes. In 2005, Plastitalia obtained an Environmental Declaration indicating endorsement by the Italian national environmental regulatory agency Eco-Management and Audit Scheme (EMAS) according to Regulations put into place by the EU. In 2010, Plastitalia also received Certification by the Italian national standardization organization Unificazione Nazionale Italiano (UNI) for mixed metal/polyethylene fittings for the conduction of combustible gas, as well as water and other fluids under pressure. Today, Plastitalia has obtained 60 international certifications and three major systems certifications. In the late 1990 s, Plastitalia positioned itself as a leader in the polyethylene fittings sector via an expansion in the world market and made a significant organizational transformation: Plastitalia changed its company name to Plastitalia S.p.A. This was an important milestone for the company.

7 WSAA Product Appraisal At the beginning of this century new technologies were adopted, the production of moulds was perfected thereby making them more sophisticated, all with the aim of creating better products. Production of electrofusion fittings commenced in The first product was the electrofusion coupler DN 110. Other diameters were added to the range, reaching up to DN Shortly after, other configurations were added up to DN 315. The wide range of electrofusion products brought about a requirement for a new way to install the fittings. Constant research and growth in technology led Plastitalia to create a new monovalent welding machine in 2003 PLAST 100. In 2012, a series of new welding machines, Iplast 105 and Iplast 30, was introduced to the market. These two machines are technically sophisticated, allowing the welding to be done safely. Research and continued improvement continues today allowing the frequent creation of new, reliable products at a competitive price. 3 THE PRODUCT The product range applicable to this appraisal, summarised in Table 1, comprises a wide range of PE100 electrofusion and long spigot pressure fittings in SDR11 which equates to PN 16 for water and sewerage applications. The electrofusion couplings are also available in other SDRs whilst spigot fittings are additionally offered in SDR9 (equivalent to PN 20 for water applications) and SDR17 (equivalent to PN 10 for water applications). The manufacturer produces other fittings that are not included in this appraisal. The manufacturer also advises they have the capability of producing special items designed to customer requirements. TABLE 1 PRODUCT RANGE Product Pressure Classes and SDR Range 1 Size Range Spigot fittings SDR9, SDR11, SDR17 DN25 to DN 400. Sizes available vary with type of fitting. Electrofusion fittings. Includes couplers, elbows, tees, reducers, endcaps and saddles. SDR11 full range. Couplings also available in SDR 7.4 and SDR 9 Comprehensive diameter range with actual sizes varying with the difference structures. Note 1 PE100 SDR9, SDR11 and SDR17 equate to PN20, PN16 and PN10 respectively The complete list of PE 100 electrofusion and spigot fittings is shown in Appendix G, noting that the metal PE transition fittings are excluded from this appraisal. 4 SCOPE OF THE APPRAIS AL This product appraisal applies to PE100 PLAST pressure fittings manufactured by Plastitalia S.p.A. The appraised range includes spigot and electrofusion fittings. The products are manufactured under ISO 9001 quality systems accreditation. The fittings are certified as complying with AS/NZS 4129 by Australian Certification Services (Certification based on ISO Guide 67 (system 5)). They are also certified for compliance with AS/NZS 4129 by Australian Certification Services to WaterMark Level 1. The products are produced using the following PE100 materials (a) (b) (c) BorSafe HE3490-LS-H, BorSafe HE3490-IM, Sabic Vestolen A6060R 1000 or (d) Sabic Vestolen A RELY 5922R 1000.

8 WSAA Product Appraisal NBR seals used in PLAST tapping tees are included in the appraisal. 5 APPRAISAL CRITERIA 5.1 Quality Assurance Requirements The WSAA Product Appraisal Technical Advisory Group accepts polyethylene electrofusion and spigot fittings for pressure applications manufactured in compliance with AS/NZS 4129:2008 Fittings for polyethylene (PE) pipes for pressure applications and duly certified by means of an ISO Type 5 product certification scheme undertaken by a JAS-ANZ accredited Certification Assessment Body (CAB) or by an international accreditation system recognised by JAS-ANZ. The manufacturer is generally expected to have a production management and control system that has been duly accredited in accordance with (AS/NZS) ISO 9001 as a prerequisite to undergoing a product certification audit. 5.2 Performance Requirements Plastitalia S.p.A PLAST electrofusion and spigot PE100 fittings have been appraised for compliance with AS/NZS 4129:2008 Fittings for polyethylene (PE) pipes for pressure applications. Test reports have been provided confirming compliance with relevant ISO and EN Standards which encompass the same performance requirements as AS/NZS In particular, ISO 4427 (water), ISO 4437 (gas), EN 1555 (gas) and EN (water). Appraisal criteria are also determined by the WSAA Product Appraisal Technical Advisory Group and regularly reviewed to ensure that the criteria reflect the requirements of WSAA members. The following Product Specifications are also relevant to this application: WSA PS-208 Polyethylene (PE) Moulded Pressure Fittings for Pressure Applications - Water Supply and Sewerage. WSA PS-329 Tapping Saddles, Electrofusion, for Use with Polyethylene (PE) Mains for Pressure Applications - Water Supply and Sewerage Copies of the above Product Specifications can be downloaded from the WSAA website. 6 COMPLIANCE WITH APPRAISAL CRITERIA 6.1 Compliance with Quality Assurance Requirements Plastitalia S.p.A is a Quality Endorsed Company certified to ISO 9001:2008 Certificate of Registration No. 179 for the Planning and production through injection moulding, welding and mechanical working of PE80 and PE100 fittings for the transport of water, gas and under pressure fluids. The ISO 9001 certificate is issued by the accredited Istituto Italiano Dei Plastics (IIP). Note the certification procedure in Italy is that IIP is a member of CISQ (Certifying Bodies Italian Association) which is the official Italian partner recognised by IQNET which receives the accreditation certificate from IIP and releases it internationally. 6.2 Compliance with Performance Requirements Plastitalia electrofusion and spigot fittings are required to comply with AS/NZS Compliance has been confirmed by viewing the Australian Certification Services ISO Type 5 product certification certificate as listed below and sighting test reports confirming satisfactory performance to the relevant tests in the Standard. Australian Certification Services has also issued Plastitalia with a Level 1 WaterMark Certificate No. AMI for compliance with AS/NZS 4129:2008. ISO Type 5 Certificate of Conformity for product compliance with AS/NZS 4129 provides confidence that the Plastitalia electrofusion fittings are manufactured for compliance with the nominated standards and requirements.

9 WSAA Product Appraisal Declaration No 0001/2013 for the elastomeric seal compound TEC N41-70 has been provided. The test results, detailed in the DVGW test report dated 2007 show compliance with UNI EN A certificate issued by DVGW for the seal manufacturer s Quality Assurance System (Expiry date 2012) has been provided as has KIWA product certificate K55481/04 issued to Tecnogomma International SPA for Vulcanised rubber products for cold and hot drinking water applications (Issued 2016). Finally a NSF certificate declaring compliance with ANSI NSF61 (Drinking Water System Components Health Effects) has been provided for the seals. AMS Laboratories test certificate demonstrating compliance with AS/NZS 4020:2005 Products for use in contact with drinking water - has been provided. The certificate is dated 27/6/2012 and has just become due for renewal. 7 FITTING INSTRUCTIONS, TRAINING AND INSTALLATION Welding instructions are provided in a technical manual, pages 18 to 23 available to registered users on the Plastitalia website Polyethylene pipe systems have been commonly used in the Australian urban water industry for many years. PE pipe manufactured in compliance with AS/NZS 4130 Polyethylene pipes for pressure applications is compatible with fittings manufactured in accordance with AS/NZS 4129:2008 Fittings for polyethylene (PE) pipes for pressure applications. It is recommended that reference be made to the suppliers or manufacturers of the fittings for the installation instructions as the method may be specific to the fitting geometry. Electrofusion welding and butt fusion processes may be used for joining pipe-to-pipe or fitting-to-pipe. All welding shall be performed by welders who have successfully completed training by a Registered Training Organisation, endorsed by the Plastics Industry Pipe Association for the relevant welding method(s). The Plastics Industry Pipe Association provides technical guidelines for electrofusion and butt welding in the following documents. (a) (b) POP001 Electrofusion Jointing of Pipe and fittings for Pressure Applications POP003 Butt Fusion Jointing of PE Pipes and Fittings Recommended Parameters. POP001 contains recommendations for equipment required, for jointing, maintenance, servicing and calibration procedures, records to be kept and the training program to be respected to produce good fusion joints in polyethylene pipes. POP003 is a guide to the butt fusion of polyethylene pipe using AS/NZS 4130 material as a basis, recommending the butt fusion procedures and parameters as specified in ISO Copies of these documents can be downloaded from the PIPA website Polyethylene pipe systems should be installed in accordance with AS/NZS 2033:2008 Installation of polyethylene pipe systems and AS/NZS Buried flexible pipelines Part 2 Installation. PE pipe shall be stored in accordance with the storage requirements of POP005 Packaging, handling and storage of polyethylene pipe and fittings. 8 PRODUCT MARKING All Plastitalia electrofusion and spigot fittings are marked in accordance with the requirements of AS/NZS 4129 and includes: (a) (b) Manufacturers Name or registered trademark: Identification, including grade and type of material, of the plastics material used for the body of the fitting, abbreviated in accordance with ISO , ASTM D1600 or AS/NZS 4131.

10 WSAA Product Appraisal (c) (d) (e) Nominal size (DN) of the pipe to which the fitting is suited. Classification in accordance with the pipe classification for which the fitting is to be used. Note for water applications the classification is PN. Date of manufacture or batch code (f) The number of this standard: AS/NZS 4129 (g) (h) (i) (j) Product Certification Licence Number: LN3013 WaterMark symbol: W Special Application information as appropriate: e.g. Example PE100 spigot fittings Plastitalia.100 PE100 dn160 SDR11 PN ST AS/NZS4129 LN3013 W Tee 90. Refer to Appendix H for other examples. 9 PACKAGING AND TRANSPORTATION All EF fittings are packed in individual bags then collectively in cartons. The number of fittings per carton being dependent upon the size and type of fitting. EF fittings should be kept in their individual plastics bag up to immediately before installation. Spigot fittings are packaged in cartons. 10 PRODUCT WARRANTY The products are covered by the normal commercial and legal requirements of the Competition and Consumer Act 2010 (Cth), which covers manufacture to the relevant standard, and details of Plastitalia warranty, is included in their terms and conditions of sale. 11 WATER AGENCY EXPERIENCE WITH THE PRODUCT OR FIELD TESTING REPORT A field testing report of the Plastitalia electrofusion and spigot fittings has not been submitted. 12 DISCUSSION The appraisal concludes that: The Plastitalia electrofusion and spigot fittings are fit for purpose and suitable for use in water supply and sewer gravity, pressure and vacuum systems. The Plastitalia electrofusion and spigot fittings spigot fittings are suitable for use with PE pipe conforming to AS/NZS The Australian Certification Services ISO Type 5 product certification certificate for the Plastitalia electrofusion and spigot fittings is accepted as meeting the additional conformity assessment requirements specified in WSAA TN OUTCOMES OF EXPERT PANEL PRODUCT REVIEW Comments received by members of the Expert Panel during the peer review period have been addressed in this version of the Report. 14 LIFE EXPECTANCY Plastitalia declares the electrofusion spigot end fittings comply with the requirements of EN for which is secured a useful life cycle of 50 years, at a temperature of 20 C and with a maximum circumferential stress of 8.0 MPa. For correctly manufactured and installed systems, the actual life cannot be predicted, but can reasonably be expected to be well in excess of 100 years before major rehabilitation is required. This rating is only a general guide to life expectancy and may vary with the quality of installation workmanship, system operating conditions, operating environment and other site specific factors.

11 WSAA Product Appraisal FUTURE WORKS No future works items have been identified. 16 DISCLAIMER This Product Appraisal Report (Report) is issued by the Water Services Association of Australia Limited on the understanding that: This Report applies to the product(s) as submitted. Any changes to the product(s) either minor or major shall void this Report. To maintain the recommendations of this Report any such changes shall be detailed and notified to the Product Appraisal Manager for consideration and review of the Report and appropriate action. Appraisals and their recommendations will be the subject of continuous review dependent upon the satisfactory performance of products. WSAA reserves the right to undertake random audits of product manufacture and installation. Where products fail to maintain appraised performance requirements the appraisal and its recommendations may be modified and reissued. Appraisal reports will be reviewed and reissued at regular intervals not exceeding five (5) years. The following information explains a number of very important limits on your ability to rely on the information in this Report. Please read it carefully and take it into account when considering the contents of this Report. Any enquiries regarding this report should be directed to the Program Manager, Carl Radford, Phone: carl.radford@wsaa.asn.au Issue of Report This Report has been published and/or prepared by the Water Services Association of Australia Limited and nominated Project Manager and peer group of technical specialists (the Publishers). The Report has been prepared for use within Australia only by technical specialists that have expertise in the function of products such as those appraised in the Report (the Recipients). By accepting this Report, the Recipient acknowledges and represents to the Publisher(s) and each person involved in the preparation of the Report that the Recipient has understood and accepted the terms of this Disclaimer Limits on Reliance on Information and Recommendations Disclaimer of liability Neither the Publisher(s) nor any person involved in the preparation of the Report accept(s) any liability for any loss or damage suffered by any person however caused (including negligence or the omission by any person to do anything) relating in any way to the Report or the product appraisal criteria underlying it. This includes (without limitation) any liability for any recommendation or information in the Report or any errors or omissions Intellectual Property and other rights The Water Services Association of Australia Limited does not undertake any assessment of whether the importation, manufacture, sale or use of the Product the subject of this Report infringes the intellectual property rights or proprietary rights of any person. Recipients of the report should undertake their own assessment of whether (as relevant) the importation, manufacture, sale or use of the relevant Products infringe the intellectual property rights or other proprietary rights of any person. If the Product infringes intellectual property rights or other proprietary rights, there is potential for the supply of the Products to be interrupted.

12 WSAA Product Appraisal From time to time the Water Services Association of Australia Limited and the other Publishers may receive notice of allegations that the importation, manufacture, sale or use of the Product infringes intellectual property rights or other proprietary rights. The Water Services Association of Australia Limited's policy is to not refer to such allegations in its reports or take any other steps to put Recipients on notice of such allegations, unless and until it is aware that the allegations have been admitted or proved in Court. As such, Recipients acknowledge, agree and accept that the Water Services Association of Australia Limited may have information in its possession about intellectual property rights infringement allegations or other infringement allegations in relation to the Product which are not referred to or disclosed in this Report and which are not otherwise communicated to Recipients Need for independent assessment The information and any recommendation contained (expressly or by implication) in this Report are provided in good faith (and subject to the limitations noted in this Report). However, you should treat the information as indicative only. You should not rely on that information or any such recommendation except to the extent that you reach an agreement to the contrary with the Publisher(s). This Report does not contain all information that a person might require for the purposes of assessing any product discussed or appraised within it. The product appraisal criteria used in preparing this Report may not address all relevant aspects of the Product. Recipients should seek independent evidence of any matter which is material to their decisions in connection with an assessment of the Product and consult their own advisers for any technical information required. Any decision to use the Product should take into account the reliability of that independent evidence obtained by the Recipient regarding the Product. Recipients should also independently verify and assess the appropriateness of any recommendation in the Report, especially given that any recommendation will not take into account a Recipient s particular needs or circumstances. WSAA has not evaluated the extent of the product liability and professional indemnify insurance that the provider of the product maintains. Recipients should ensure that they evaluate the allocation of liability for product defects and any professional advice obtained in relation to the product or its specification including the requirements for product liability and professional indemnity insurance No Updating Neither the Publisher(s) nor any person involved in the preparation of this Report [has] [have] any obligation to notify you of any change in the information contained in this Report or of any new information concerning the Publisher(s) or the Product or any other matter No Warranty The Publisher(s) do[es] not, in any way, warrant that steps have been taken to verify or audit the accuracy or completeness of the information in this Report, or the accuracy, completeness or reasonableness of any recommendation in this Report.

13 WSAA Product Appraisal APPENDIX A - TECHNICAL LITERATURE

14 WSAA Product Appraisal

15 WSAA Product Appraisal

16 WSAA Product Appraisal APPENDIX B - QUALITY CERTIFICATIONS Copies of the following Quality Certification Certificates are available for downloading from the WSAA Members Only Product Appraisal Technical Advisory Group Portal Website. TABLE B1 PLASTITALIA MANAGEMENT SYSTEMS Applicant s Business Plastitalia S.p.A Via Ferrara snc Brolo (Messina) Italy Quality Systems Standard UNI EN ISO 9001:2008 Certification licence no. Certifying agency IIP Certificate number 179 IQNET Registration number IT-3355 CISQ First date of certification 2/10/2014 Current date of certification 2/10/2014 Expiry date of certification 2/11/2017 TABLE B2: HYDROFLOW DISTRIBUTORS LTD MANAGEMENT SYSTEMS Address: Hydroflow Distributors Ltd Albany, 221 & 221A Bush Road, Albany, Auckland, NZ Hydroflow Distributors Ltd Wigram, 58 Hammersmith Drive, Wigram, Christchurch, NZ Hydroflow Distributors Ltd Hornby, 5 Canada Crescent, Hornby, Christchurch, NZ Hydroflow (Aust) Pty Ltd Melbourne, 24 Harcourt Road, Altona, Melbourne, AU Quality Systems Standard AS/NZS ISO 9001:2008 Certification Registration no Certifying agency Telarc SAI Ltd First date of certification 5 August 2011 Current date of certification 3 July 2017 Expiry date of certification 15 September 2018 TABLE B3 PLASTITALIA PRODUCT CERTIFICATION Manufacturing Plant Plastitalia S.p.A Via Ferrara snc Brolo (Messina) Italy Product Standard/Spec. AS/NZS 4129:2008 Confirmation No Expires 5/4/2021 Issuing certification body Australian Certification Services Pty Ltd

17 WSAA Product Appraisal TABLE B4 PLASTITALIA PRODUCT CERTIFICATION Manufacturing Plant Plastitalia S.p.A Via Ferrara snc Brolo (Messina) Italy Certificate of Conformity EN Confirmation No. No 437/2012 Rev 5 Issued 30/1/2017 Issuing certification body Istituto Italiano Dei Plastici S.r.L. TABLE B5 PLASTITALIA WATERMARK CERTIFICATION Manufacturing Plant Plastitalia S.p.A Via Ferrara snc Brolo (Messina) Italy Product Standard/Spec. AS/NZS 4129:2008 Confirmation No EXPIRES 3/6/2020 Issuing certification body Australian Certification Services Pty Ltd TABLE B6 PLASTITALIA ENVIRONMENTAL MANAGEMENT SYSTEM CERTIFICATION Manufacturing Plant Plastitalia S.p.A Via Ferrara snc Brolo (Messina) Italy Product Standard/Spec. ISO 14001:2004 Confirmation No. IT EXPIRES 2/11/2017 Issuing certification body CISQ TABLE B7 PLASTITALIA OCCUPATIONAL HEALTH AND SAFETY MANAGEMENT SYSTEMS Manufacturing Plant Plastitalia S.p.A Via Ferrara snc Brolo (Messina) Italy Product Standard/Spec. ISO 18001:2007 Confirmation No. IT EXPIRES 21/7/2019 Issuing certification body CISQ Laboratory accreditation Plastitalia S.p.A Certificate of conformity for fittings made in PE. Issued by Bureau Veritas. Certificate of conformity for fittings made in PE TABLE B8 PLASTITALIA OTHER CERTIFICATIONS Manufacturing Plant Plastitalia S.p.A Via Ferrara snc Brolo (Messina) Italy EN ISO/IEC Accreditation number 1622 Expires Awarded by Ilarc associated ACCREDIA Conformity to EN Plastics piping systems tor water supply, and tor drainage and sewerage under pressure - Polyethylene (PE) - Part 3: Fittings. Expiry date 03/03/2019 Conformity to EN Plastics piping systems tor water supply, and tor drainage and sewerage under pressure IIP. Expires 31/12/2017

18 WSAA Product Appraisal Certificate of compliance for polyethylene fittings issued by FM Approvals Certificate of compliance for fusion fittings made of PE issued by KIWA Water regulations advisory service (WRAS) Water regulations advisory service (WRAS) DVGW Type examination certificate Manufacturing Plant Plastitalia S.p.A Via Ferrara snc Brolo (Messina) Italy Approval dated September Compliance with KIWA guideline BRL-K17105 Piping systems for PE for transport of drinking water and raw water. Dated Compliance with UK water supply regulations. Valid until 31 December Certificate number Applies to PLAST range of butt weld and electrofusion fittings. Material approval for PLAST spigot and electrofusion black coloured PE100 fittings. Expiry date April 2018 Includes range of PE-HD spigot and electrofusion fittings. Expires Declaration by Plastitalia Materials used in the fittings are in accordance with EN Plastitalia Quality test plan NSF International KIWA Kiwa Product certificate K55481/04 NSF51 compliance certificate for Tecnogomma International SRL NBR seals. October 2010 Compliance of Tecnogomma International seals with EN Vulcanised seals. Issued 15/11/2016

19 WSAA Product Appraisal

20 WSAA Product Appraisal

21 WSAA Product Appraisal

22 WSAA Product Appraisal

23 WSAA Product Appraisal

24 WSAA Product Appraisal

25 WSAA Product Appraisal

26 WSAA Product Appraisal APPENDIX C - WSA PRODUCT SPECIFICATION

27 WSAA Product Appraisal

28 WSAA Product Appraisal

29 WSAA Product Appraisal APPENDIX D - SUPPLIER CONTACTS Andrew Thin National Business Development Manager PE Systems Hydroflow Distributors (Aust) Pty Ltd 24 Harcourt Road, Altona, Victoria, Mobile: +61 (0) Fax: Freecall

30 WSAA Product Appraisal APPENDIX E - NATA LABORATORY TEST RESULTS AMS Laboratories Report I dated 27/6/2012 for effect on drinking water.

31 WSAA Product Appraisal APPENDIX F - LABORATORY TEST RESULTS IIP Test report No 0006LP/2017 Dated 20/1/2017 covering carbon black content, OIT, MFR, dispersion, pressure testing and dimensions.

32 WSAA Product Appraisal EF FITTINGS APPPENDIX G PRODUCT RANGE ELECTROFUSION COUPLER Single shoot Double shoot SDR 17 dn code DE Z 90 MP090B MP110B MP125B MP140B MP160B MP180B MP200B MP225B MP250B MP280B MP315B MP355B MP400B MP450B MP500B * MP560B * MP630B *Double shoot Characteristics of the electric circuit Diameter of the connector (mm) 4.0 Voltage (V) 39.5

33 WSAA Product Appraisal ELECTROFUSION COUPLER Single shoot Double shoot SDR 11 *Double shoot Dn Code DE Z 20 MP020C MP025C MP032C MP040C MP050C MP063C MP075C MP090C MP110C MP125C MP140C MP160C MP180C MP200C MP225C MP250C MP280C MP315C MP355C MP400C * MP450C * MP500C * MP560C * MP630C Characteristics of the electric circuit Diameter of the connector (mm) 4.0 Voltage (V) 39.5

34 WSAA Product Appraisal ELECTROFUSION COUPLER Single shoot Double shoot SDR *Double shoot dn code DE Z 32 MP032H MP040H MP050H MP063H MP075H MP090H MP110H MP125H MP140H MP160H MP180H MP200H MP225H MP250H MP280H MP315H MP355H MP400H MP450G* MP500H* MP560H* MP630H* - - Characteristics of the electric circuit Diameter of the connector (mm) 4.0 Voltage (V) 39.5

35 WSAA Product Appraisal ELECTROFUSION ELBOW 90 SDR 11 dn code Z 20 GE9P020C GE9P025C GE9P032C GE9P040C GE9P050C GE9P063C GE9P075C GE9P090C GE9P110C GE9P125C GE9P140C GE9P160C GE9P180C GE9P200C GE9P225C GE9P250C GE9P280C GE9P315C 383 Characteristics of the electric circuit Diameter of the connector (mm) 4.0 Voltage (V) 39.5

36 WSAA Product Appraisal ELECTROFUSION ELBOW 45 SDR 11 dn code Z 20 GE4P020C GE4P025C GE4P032C GE4P040C GE4P050C GE4P063C GE4P075C GE4P090C GE4P110C GE4P125C GE4P140C GE4P160C GE4P180C GE4P200C GE4P225C GE4P250C GE4P280C GE4P315C 275 Characteristics of the electric circuit Diameter of the connector (mm) 4.0 Voltage (V) 39.5

37 WSAA Product Appraisal ELECTROFUSION ELBOW SDR 11 dn code Z 90 GE2250P090C GE2250P110C GE2250P125C GE2250P140C GE2250P160C GE2250P180C GE2250P200C GE2250P225C GE2250P250C GE2250P280C GE2250P315C 185 Characteristics of the electric circuit Diameter of the connector (mm) 4.0 Voltage (V) 39.5

38 WSAA Product Appraisal ELECTROFUSION ELBOW SDR 11 dn code Z 90 GE1125P090C GE1125P110C GE1125P125C GE1125P140C GE1125P160C GE1125P180C GE1125P200C 225 GE1125P225C GE1125P250C GE1125P280C GE1125P315C 170 Characteristics of the electric circuit Diameter of the connector (mm) 4.0 Voltage (V) 39.5

39 WSAA Product Appraisal ELECTROFUSION TEE 90 SDR 11 dn code H Z 20 TEP020C TEP025C TEP032C TEP040C TEP050C TEP063C TEP075C TEP090C TEP110C TEP125C TEP140C TEP160C TEP180C TEP200C TEP225C TEP250C TEP315C Characteristics of the electric circuit Diameter of the connector (mm) 4.0 Voltage (V) 39.5

40 WSAA Product Appraisal ELECTROFUSION REDUCED TEE 90 SDR 11 dn dn1 code H Z TREP090063C TREP090075C TREP110063C TREP125063C TREP125090C TREP140110C TREP160110C TREP180090C TREP180125C TREP200090C TREP200125C TREP200180C TREP225110C TREP225160C TREP250125C TREP250180C TREP315125C TREP315180C Characteristics of the electric circuit Diameter of the connector (mm) 4.0 Voltage (V) 39.5

41 WSAA Product Appraisal ELECTROFUSION REDUCER SDR 11 dn dn1 code Z REP025020C REP032020C REP032025C REP040020C REP040025C REP040032C REP050025C REP050032C REP050040C REP063025C REP063032C REP063040C REP063050C REP075050C REP075063C REP090050C REP090063C REP090075C REP110063C REP110075C REP110090C REP125063C REP125090C REP125110C REP140090C REP160090C REP160110C REP160125C 244

42 WSAA Product Appraisal dn dn1 code Z REP180090C REP180125C REP180140C REP180160C REP200160C REP200180C REP225160C REP250180C REP315200C 415 Characteristics of the electric circuit Diameter of the connector (mm) 4.0 Voltage (V) 39.5

43 WSAA Product Appraisal ELECTROFUSION END CAP SDR 11 dn code H Z 20 CAEP020C CAEP025C CAEP032C CAEP040C CAEP050C CAEP063C CAEP125C CAEP090C CAEP110C CAEP125C CAEP140C CAEP160C CAEP180C CAEP200C CAEP225C CAEP250C CAEP280C CAEP315C Characteristics of the electric circuit Diameter of the connector (mm) 4.0 Voltage (V) 39.5

44 WSAA Product Appraisal ELECTROFUSION TAPPING TEE SDR 11 dn dn1 code H H1 L CPCP040020C CPCP050020C CPCP063020C CPCP075020C CPCP090020C CPCP110020C CPCP125025C CPCP140020C CPCP160020C CPCP180020C CPCP200020C CPCP225020C CPCP250020C CPCP280020C CPCP315020C CPCP040025C CPCP050025C CPCP063025C CPCP075025C CPCP090025C CPCP110025C CPCP125025C CPCP140025C CPCP160025C CPCP180025C CPCP200025C CPCP225025C CPCP250025C CPCP280025C CPCP315025C

45 WSAA Product Appraisal dn dn1 code H H1 L CPCP040032C CPCP050032C CPCP063032C CPCP075032C CPCP090032C CPCP110032C CPCP125032C CPCP140032C CPCP160032C CPCP180032C CPCP200032C CPCP225032C CPCP250032C CPCP250032C CPCP315032C CPCP063040C CPCP075040C CPCP090040C CPCP110040C CPCP125040C CPCP140040C CPCP160040C CPCP180040C CPCP200040C CPCP225040C CPCP250040C CPCP280040C CPCP315040C CPCP063050C CPCP075050C CPCP090050C CPCP110050C CPCP125050C CPCP140050C CPCP160050C CPCP180050C CPCP200050C CPCP225050C CPCP250050C CPCP280050C CPCP315050C CPCP063063C CPCP075063C CPCP090063C CPCP110063C

46 WSAA Product Appraisal dn dn1 code H H1 L CPCP125063C CPCP140063C CPCP160063C CPCP180063C CPCP200063C CPCP225063C CPCP250063C CPCP280063C CPCP315063C Characteristics of the electric circuit Diameter of the connector (mm) 4.0 Voltage (V) 39.5

47 WSAA Product Appraisal ELECTROFUSION TAPPING TEE WITH SAFETY GAS STOP SDR 11 dn dn1 code H H CPCPGS040020C CPCPGS050020C CPCPGS063020C CPCPGS075020C CPCPGS090020C CPCPGS110020C CPCPGS125020C CPCPGS140020C CPCPGS160020C CPCPGS180020C CPCPGS200020C CPCPGS225020C CPCPGS250020C CPCPGS280020C CPCPGS315020C CPCPGS040032C CPCPGS050032C CPCPGS063032C CPCPGS075032C CPCPGS090032C CPCPGS110032C CPCPGS125032C CPCPGS140032C CPCPGS160032C CPCPGS180032C CPCPGS200032C CPCPGS225032C CPCPGS250032C CPCPGS280032C CPCPGS315032C Characteristics of the electric circuit Diameter of the connector (mm) 4.0 Voltage (V) 39.5

48 WSAA Product Appraisal ELECTROFUSION BALLON SADDLE SDR 11 dn code H 90 CPSP090RIPC CPSP110RIPC CPSP125RIPC CPSP140RIPC CPSP160RIPC CPSP180RIPC CPSP200RIPC CPSP225RIPC CPSP250RIPC CPSP280RIPC CPSP315RIPC 70 Characteristics of the electric circuit Diameter of the connector (mm) 4.0 Voltage (V) 39.5

49 WSAA Product Appraisal ELECTROFUSION BRANCH SADDLE SDR 11 dn dn1 code H CPSP040020C CPSP050020C CPSP063020C CPSP075020C CPSP090020C CPSP110020C CPSP125020C CPSP140020C CPSP160020C CPSP180020C CPSP200020C CPSP225020C CPSP250020C CPSP280020C CPSP315020C CPSP040025C CPSP050025C CPSP063025C CPSP075025C CPSP090025C CPSP110025C CPSP125025C CPSP140025C CPSP160025C CPSP180025C CPSP200025C CPSP225025C CPSP250025C CPSP280025C CPSP315025C 65

50 WSAA Product Appraisal dn dn1 code H CPSP040032C CPSP050032C CPSP063032C CPSP075032C CPSP090032C CPSP110032C CPSP125032C CPSP140032C CPSP160032C CPSP180032C CPSP200032C CPSP225032C CPSP250032C CPSP280032C CPSP315032C CPSP050040C CPSP063040C CPSP075040C CPSP090040C CPSP110040C CPSP125040C CPSP140040C CPSP160040C CPSP180040C CPSP200040C CPSP225040C CPSP250040C CPSP280040C CPSP315040C CPSP063050C CPSP075050C CPSP090050C CPSP110050C CPSP125050C CPSP140050C CPSP160050C CPSP180050C CPSP200050C CPSP225050C CPSP250050C CPSP280063C CPSP315063C CPSP063063C CPSP075063C CPSP090063C 75

51 WSAA Product Appraisal dn dn1 code H CPSP110063C CPSP125063C CPSP140063C CPSP160063C / CPSP180/200063C / CPSP225/280063C / CPSP315/450063C /900* 63 CPSP500/900063C CPSP110075C CPSP125075C CPSP140075C CPSP160075C / CPSP180/200075C / CPSP225/280075C / CPSP315/450075C /900* 75 CPSP500/900075C CPSP090090C CPSP110090C CPSP125090C CPSP140090C CPSP160090C / CPSP180/200090C / CPSP225/280090C / CPSP315/450090C /900* 90 CPSP500/900090C 90 Characteristics of the electric circuit Diameter of the connector (mm) 4.0 Voltage (V) 39.5

52 WSAA Product Appraisal ELECTROFUSION HIGH VOLUME BRANCH SADDLE SDR 11 dn dn1 code H CPSP125110C CPSP160110C CPSP180110C / CPSP220/225110C / CPSP250/280110C / CPSP315/400110C / CPSP450/500110C / CPSP560/630110C CPSP160125C CPSP180125C / CPSP220/225125C / CPSP250/280125C / CPSP315/400125C / CPSP450/500125C / CPSP560/630125C / CPSP315/400160C / CPSP450/500160C / CPSP560/630160C CPSP315200C CPSP355200C CPSP400200C CPSP450200C CPSP500200C CPSP560200C CPSP630200C CPSP315225C CPSP355225C CPSP400225C CPSP450225C CPSP500225C CPSP560225C 160

53 WSAA Product Appraisal CPSP630225C CPSP500250C CPSP560250C CPSP630250C CPSP630315C 160 Characteristics of the electric circuit Diameter of the connector (mm) 4.0 Voltage (V) 39.5

54 WSAA Product Appraisal SPIGOT FITTINGS TEE 90 LONG SPIGOT INJECTION MOULDED SDR 17 dn code H Z 25 TP025B TP032B TP040B TP050B TP063B TP075B TP090B TP110B TP125B TP140B TP160B TP180B TP200B TP225B TP250B TP280B TP315B TP355B TP400B TP450B TP500B TP560B TP630B

55 WSAA Product Appraisal TEE 90 LONG SPIGOT INJECTION MOULDED SDR 11 dn code H Z 25 TP025C TP032C TP040C TP050C TP063C TP075C TP090C TP110C TP125C TP140C TP160C TP180C TP200C TP225C TP250C TP280C TP315C TP355C TP400C TP450C TP500C TP560C TP630C

56 WSAA Product Appraisal TEE 90 LONG SPIGOT INJECTION MOULDED SDR 9 dn code H Z 25 TP025G TP032G TP040G TP050G TP063G TP075G TP090G TP110G TP125G TP140G TP160G TP180G TP200G TP225G TP250G TP280G TP315G TP355G TP400G TP450G TP500G TP560G TP630G

57 WSAA Product Appraisal REDUCED TEE 90 LONG SPIGOT INJECTION MOULDED SDR 17 dn dn code H H1 Z TRP090050B TRP090063B TRP110050B TRP110063B TRP110090B TRP125063B TRP125090B TRP140063B TRP140090B TRP160063B TRP160090B TRP160110B TRP160125B TRP180063B TRP180090B TRP180110B TRP180125B TRP200063B TRP200090B TRP200110B TRP200125B TRP200160B TRP200180B TRP225090B TRP225125B TRP225160B TRP225180B TRP250110B TRP250125B TRP250160B

58 WSAA Product Appraisal dn dn code H H1 Z TRP250180B TRP250200B TRP280110B TRP315110B TRP315125B TRP315160B TRP315180B TRP315200B TRP315225B TRP355110B TRP355160B TRP355225B TRP400110B TRP400160B TRP400225B TRP450160B TRP450225B TRP450315B TRP500160B TRP500250B TRP560250B TRP630160B TRP630250B

59 WSAA Product Appraisal REDUCED TEE 90 LONG SPIGOT INJECTION MOULDED SDR 11 dn dn code H H1 Z TRP090050C TRP090063C TRP110050C TRP110063C TRP110090C TRP125063C TRP125090C TRP140063C TRP140090C TRP160063C TRP160090C TRP160110C TRP160125C TRP180063C TRP180090C TRP180110C TRP180125C TRP200063C TRP200090C TRP200110C TRP200125C TRP200160C TRP200180C TRP225090C TRP225125C TRP225160C TRP225180C TRP250110C TRP250125C TRP250160C TRP250180C

60 WSAA Product Appraisal dn dn code H H1 Z TRP250200C TRP280110C TRP315110C TRP315125C TRP315160C TRP315180C TRP315200C TRP315225C TRP355110C TRP355160C TRP355225C TRP400110C TRP400160C TRP400225C TRP450160C TRP450225C TRP450315C TRP500160C TRP500250C TRP560250C TRP630160C TRP630250C

61 WSAA Product Appraisal REDUCED TEE 90 LONG SPIGOT INJECTION MOULDED SDR 9 dn dn code H H1 Z TRP090050G TRP090063G TRP110050G TRP110063G TRP110090G TRP125063G TRP125090G TRP140063G TRP140090G TRP160063G TRP160090G TRP160110G TRP160125G TRP180063G TRP180090G TRP180110G TRP180125G TRP200063G TRP200090G TRP200110G TRP200125G TRP200160G TRP200180G TRP225090G TRP225125G TRP225160G TRP225180G TRP250110G TRP250125G

62 WSAA Product Appraisal dn dn code H H1 Z TRP250160G TRP250180G TRP250200G TRP280110G TRP315110G TRP315125G TRP315160G TRP315180G TRP315200G TRP315225G TRP355110G TRP355160G TRP355225G TRP400110G TRP400160G TRP400225G TRP450160G TRP450225G TRP450315G TRP500160G TRP500250G TRP560250G TRP630160G TRP630250G

63 WSAA Product Appraisal TEE 45 LONG SPIGOT INJECTION MOULDED SDR 17 dn code H H1 Z 63 T4P063B T4P075B T4P090B T4P110B T4P125B T4P140B T4P160B SDR 11 dn code H H1 Z 63 T4P063C T4P075C T4P090C T4P110C T4P125C T4P140C T4P160C

64 WSAA Product Appraisal ELBOW 90 LONG SPIGOT INJECTION MOULDED SDR 17 dn code H Z 25 G9P025B G9P032B G9P040B G9P050B G9P063B G9P075B G9P090B G9P110B G9P125B G9P140B G9P160B G9P180B G9P200B G9P225B G9P250B G9P280B G9P315B G9P355B G9P400B

65 WSAA Product Appraisal ELBOW 90 LONG SPIGOT INJECTION MOULDED SDR 11 dn code H Z 25 G9P025C G9P032C G9P040C G9P050C G9P063C G9P075C G9P090C G9P110C G9P125C G9P140C G9P160C G9P180C G9P200C G9P225C G9P250C G9P280C G9P315C G9P355C G9P400C

66 WSAA Product Appraisal ELBOW 90 LONG SPIGOT INJECTION MOULDED SDR 17 dn code H Z 25 G9P025G G9P032G G9P040G G9P050G G9P063G G9P075G G9P090G G9P110G G9P125G G9P140G G9P160G G9P180G G9P200G G9P225G G9P250G G9P280G G9P315G G9P355G G9P400G

67 WSAA Product Appraisal ELBOW 45 LONG SPIGOT INJECTION MOULDED SDR 17 dn code H Z 32 G4P032B G4P040B G4P050B G4P063B G4P075B G4P090B G4P110B G4P125B G4P140B G4P160B G4P180B G4P200B G4P225B G4P250B G4P280B G4P315B G4P355B G4P400B

68 WSAA Product Appraisal ELBOW 45 LONG SPIGOT INJECTION MOULDED SDR 11 dn code H Z 32 G4P032C G4P040C G4P050C G4P063C G4P075C G4P090C G4P110C G4P125C G4P140C G4P160C G4P180C G4P200C G4P225C G4P250C G4P280C G4P315C G4P355C G4P400C

69 WSAA Product Appraisal ELBOW 45 LONG SPIGOT INJECTION MOULDED SDR 9 dn code H Z 32 G4P032G G4P040G G4P050G G4P063G G4P075G G4P090G G4P110G G4P125G G4P140G G4P160G G4P180G G4P200G G4P225G G4P250G G4P280G G4P315G G4P355G G4P400G

70 WSAA Product Appraisal REDUCER LONG SPIGOT INJECTION MOULDED SDR 17 dn dn code H H1 Z RP025020B RP032020B RP032025B RP040020B RP040025B RP040032B RP050025B RP050032B RP050040B RP063025B RP063032B RP063040B RP063050B RP075032B RP075040B RP075050B RP075063B RP090050B RP090063B RP090075B RP110050B RP110063B RP110075B RP110090B RP125063B RP125075B RP125090B RP125110B RP140090B RP140110B RP140125B

71 WSAA Product Appraisal dn dn code H H1 Z RP160090B RP160110B RP160125B RP160140B RP180063B RP180110B RP180125B RP180140B RP180160B RP200090B RP200140B RP200160B RP RP225110B RP225160B RP225180B RP225200B RP250180B RP250200B RP250225B RP315225B RP315250B

72 WSAA Product Appraisal REDUCER LONG SPIGOT INJECTION MOULDED SDR 11 dn dn code H H1 Z RP025020C RP032020C RP032025C RP040020C RP040025C RP040032C RP050025C RP050032C RP050040C RP063025C RP063032C RP063040C RP063050C RP075032C RP075040C RP075050C RP075063C RP090050C RP090063C RP090075C RP110050C RP110063C RP110075C RP110090C RP125063C RP125075C RP125090C RP125110C RP140090C RP140110C RP140125C

73 WSAA Product Appraisal dn dn code H H1 Z RP160090C RP160110C RP160125C RP160140C RP180063C RP180110C RP180125C RP180140C RP180160C RP200090C RP200140C RP200160C RP200180C RP225110C RP225160C RP225180C RP225200C RP250180C RP250200C RP250225C RP315225C RP315250C

74 WSAA Product Appraisal REDUCER LONG SPIGOT INJECTION MOULDED SDR 9 dn dn code H H1 Z RP025020G RP032020G RP032025G RP040020G RP040025G RP040032G RP050025G RP050032G RP050040G RP063025G RP063032G RP063040G RP063050G RP075032G RP075040G RP075050G RP075063G RP090050G RP090063G RP090075G RP110050G RP110063G RP110075G RP110090G RP125063G RP125075G RP125090G RP125110G RP140090G RP140110G

75 WSAA Product Appraisal dn dn code H H1 Z RP140125G RP160090G RP160110G RP160125G RP160140G RP180063G RP180110G RP180125G RP180140G RP180160G RP200090G RP200140G RP200160G RP200180G RP225110G RP225160G RP225180G RP225200G RP250180G RP250200G RP250225G RP315225G RP315250G

76 WSAA Product Appraisal FLANGE ADAPTOR LONG SPIGOT INJECTION MOULDED SDR 17 dn code H F B C A 25 CP025C CP032C CP040C CP050C CP063B CP075B CP090B CP110B CP125B CP140B CP160B CP180B CP200B CP225B CP250B CP280B CP315B CP355B CP400B

77 WSAA Product Appraisal FLANGE ADAPTOR LONG SPIGOT INJECTION MOULDED SDR 11 dn code H F B C A 25 CP025C CP032C CP040C CP050C CP063C CP075C CP090C CP110C CP125C CP140C CP160C CP180C CP200C CP225C CP250C CP280C CP315C CP355C CP400C

78 WSAA Product Appraisal FLANGE ADAPTOR LONG SPIGOT INJECTION MOULDED SDR 9 dn code H F B C A 25 CP025G CP032G CP040G CP050G CP063G CP075G CP090G CP110G CP125G CP140G CP160G CP180G CP200G CP225G CP250G CP280G CP315G

79 WSAA Product Appraisal END CAP LONG SPIGOT INJECTION MOULDED SDR 17 dn code H Z 20 CAP020B CAP025B CAP032B CAP040B CAP050B CAP063B CAP075B CAP090B CAP110B CAP125B CAP140B CAP160B CAP180B CAP200B CAP225B CAP250B CAP280B CAP315B CAP315B CAP400B

80 WSAA Product Appraisal END CAP LONG SPIGOT INJECTION MOULDED SDR 11 dn code H Z 20 CAP020C CAP025C CAP032C CAP040C CAP050C CAP063C CAP075C CAP090C CAP110C CAP125C CAP140C CAP160C CAP180C CAP200C CAP225C CAP250C CAP280C CAP315C CAP315C CAP400C

81 WSAA Product Appraisal END CAP LONG SPIGOT INJECTION MOULDED SDR 9 dn code H Z 25 CAP025G CAP032G CAP040G CAP050G CAP063G CAP075G CAP090G CAP110G CAP125G CAP140G CAP160G CAP180G CAP200G CAP225G CAP250G CAP280G CAP315G CAP315G CAP400G

82 WSAA Product Appraisal CROSS LONG SPIGOT INJECTION MOULDED SDR 17 dn code H Z 63 CRP063B CRP075B CRP090B CRP110B CRP125B CRP140B CRP160B SDR 11 dn code H Z 63 CRP063C CRP075C CRP090C CRP110C CRP125C CRP140C CRP160C

83 WSAA Product Appraisal CROSS LONG SPIGOT INJECTION MOULDED SDR17 dn dn code H H1 Z Z CRP125090B SDR11 dn dn code H H1 Z Z CRP125090C Y LONG SPIGOT INJECTION MOULDED SDR 11 dn dn1 code H H1 Z YRP032025C YRP040032C YRP050040C

84 WSAA Product Appraisal APPENDIX H MARKING DETAILS

85 WSAA Product Appraisal

86 WSAA Product Appraisal