Clearmake Pty Ld. Product Appraisal Report TWA 0803

Transcription

1 Clearmake Pty Ld Product Appraisal Report TWA 0803 Separator Systems for Light Liquids CB1.0 SS 720L/hr CL1.5 SS 720L/hr CL1.5 SSD 1440L/hr CL3.0 SS 1600L/hr CL3.0 SSD 1140L/hr Published - February February 2010 Page 1

2 Overview of WSAA The Water Services Association of Australia (WSAA) is the peak body of the Australian urban water industry. Its 30 members and 31 associate members provide water and wastewater services to approximately 16 million Australians and to many of our largest industrial and commercial enterprises. WSAA membership also includes two members and one associate member from New Zealand. Urban water service providers have a critical role in ensuring that Australians have access to adequate and high quality water services. As Australia s population continues to grow, with most of this growth occurring in cities, that role becomes increasingly important. WSAA s vision is for Australian urban water utilities to be valued as leaders in the innovative, sustainable and cost effective delivery of water services. WSAA strives to achieve this vision by promoting knowledge sharing, networking and cooperation amongst members. WSAA identifies emerging issues and develops industry-wide responses. WSAA is the national voice of the urban water industry, speaking to government, the broader water sector and the Australian community. Copyright This document is copyrighted. Apart from any use as permitted under the Copyright Act 1968, no part of this document may be reproduced or transmitted in any form or by any means, electronically or mechanical, for any purpose, without the express written permission of the Water Services Association of Australia Ld. Water Services Association of Australia Ltd, 2008 ALL RIGHTS RESERVED 24 February 2010 Page 2

3 Table of Contents 1. Executive Summary Company Overview Scope of this Appraisal Appraisal Criteria Quality Assurance Requirements Compliance to the Appraisal Criteria Performance Requirements Applicability Specifications and Drawings Warranty Installation Requirements Operation and Maintenance Identification Outcomes of WSAA Network Review WSAA Member and Field Reports Future Works Discussion Report Recommendation Disclaimer Appendix A Product Specifications Appendix B Product Testing Appendix C Product Specifications/Drawings Appendix C Product Specifications/Drawings Appendix D Supplier Contacts February 2010 Page 3

4 1. Executive Summary Clearmake is an Australian-owned company that designs equipment from small, single-component systems such as GPT's and oil/water separators through to custom-engineered specialty systems that may incorporate rain water harvesting, storm water management, spill control, water treatment, water recycling and sludge dewatering. Products and systems comply with Local Council requirements, EPA, AQIS and OH&S regulations, and meet Australian Standards for manufacturing. The scope of this appraisal covers separator Systems for Light Liquids manufactured from stainless steel in Model Numbers CB1.0 SS, CL1.5 SS, CL1.5 SSD, CL3.0 SS, and CL3.0SSD with vertical-tube coalescing packs constructed from Oleophilic Polypropylene. The product range is applicable to the following applications a. Mechanical repair workshops b. Panel beating workshops c. Vehicle detailing d. Motor wreckers e. Motor vehicle dealerships f. Hire Companies This Appraisal Report has been compared against the requirements of the WSAA Specification WSA PS 810 Separator Systems for Light Liquids (See appendix A). Examination of all of the submitted documented material provides an expectation that the products described here in sourced and distributed by Clearmake Pty Ld are fit for purpose in the applications described in this report subject to future works items. It is recommended that WSAA Members and Associates, subject to any specific requirements of the Member or Associate, accept or authorise the Clearmake product range as detailed in this report for use in sewer networks provided design, installation, acceptance testing and commissioning are in accordance with relevant WSAA Codes, WSAA Member Integrated Codes, and the manufacturer s requirements. 2. Company Overview Clearmake is an Australian-owned company that designs equipment from small, single-component systems such as GPT's and oil/water separators through to custom-engineered specialty systems that may incorporate rain water harvesting, storm water management, spill control, water treatment, water recycling and sludge dewatering. Products and systems comply with Local Council requirements, EPA, AQIS and OH&S regulations, and meet Australian Standards for manufacturing. All design and manufacturing is centralised in SE Queensland for greater quality control and preinstall testing. This strong focus on design innovation and quality has seen Clearmake selected for The Australian Technology Showcase, a State and Federal Government initiative to promote Australian Innovation globally. 24 February 2010 Page 4

5 3. Scope of this Appraisal The scope of this appraisal covers separator Systems for Light Liquids manufactured from stainless steel in Model Numbers CB1.0 SS, CL1.5 SS, CL1.5 SSD, CL3.0 SS, and CL3.0SSD with vertical-tube coalescing packs constructed from Oleophilic Polypropylene. The Models designated SS have a Mono Helical low shear pump. The SSD Models have a diaphragm pump fitted. Both pumps are designed to transfer waste water without emulsifying the waste water stream and inhibiting separation efficiency. All other design characteristics are similar. Material of Construction CB 1.0SS CL1.5 SS CL1.5 SSD CL 3.0 SS CL3.0 SSD 304 Stainless Steel 1.6mm Thick 304 Stainless Steel 1.6mm Thick 304 Stainless Steel 1.6mm Thick 304 Stainless Steel 1.6mm Thick 304 Stainless Steel 1.6mm Thick Max. Flow Rate.28 L/s 0.42 L/s 0.31 L/s 0.83 L/s 0.31 L/s Actual Flow Rate.20 L/s 0.20 L/s 0.31 L/s 0.42 L/s 0.31 L/s Separation Process Coalescing Medium Dimensions Tube Pack Enhanced Gravity Vertical tube Packs x 1 Enhanced Gravity Vertical tube Packs x 1 Enhanced Gravity Vertical tube Packs x 1 Enhanced Gravity Vertical tube Packs x 2 Enhanced Gravity Vertical tube Packs x 2 Width 290 mm 370 mm 370 mm 370 mm 370 mm Length 775 mm 620 mm 620 mm 620 mm 620 mm Height 275 mm 350 mm 350 mm 350 mm 350 mm Weight Dry 49 kg 62 kg 56 kg 80 kg 80 kg Weight - Unfitted 41 kg 50 kg kg 78 Weight Full 205 kg 225 kg 225 kg 322 kg 322 kg Volume 156 L 169 L 169 L 242 L 242 L Inlet diameter 40 mm BSPF 40 mm BSPF 40 mm BSPF 40 mm BSPF 40 mm BSPF Outlet diameter 50 mm BSPF 50 mm BSPF 50 mm BSPF 50 mm BSPF 50 mm BSPF Oil skimmer Outlet diameter Stand Construction 40 mm BSPF 40 mm BSPF 40 mm BSPF 40 mm BSPF 40 mm BSPF 25mm SHS 304 Stainless Steel 25mm SHS 304 Stainless Steel Pump Model Mono CP11RJ Mono CP11RJ Dimensions: 25mm SHS 304 Stainless Steel Clearmake CM mm SHS 304 Stainless Steel Mono CP25RJ 25mm SHS 304 Stainless Steel Clearmake CM 1000 Width 360 mm 445 mm 445 mm 445 mm 445 mm 24 February 2010 Page 5

6 Length 1260 mm 1210 mm 1210 mm 1945 mm 1945 mm Height 1230 mm 1240 mm 1240 mm 1240 mm 1240 mm 4. Appraisal Criteria This Appraisal Report has been compared against the requirements of the WSAA Specification WSA PS 810 Separator Systems for Light Liquids (See appendix A). 5. Quality Assurance Requirements The WSAA product appraisal network accepts system (ISO 9001) and product certification by a Certification Body at the manufacturing site of strategic products to appropriate Australian or internationally recognised standards. The Certification Body shall have relevant accreditation by the Joint Accreditation System of Australia and New Zealand (JAS-ANZ) or by an equivalent international accreditation system recognised by JAS-ANZ. The manufacturer Clearmake is not ISO9001:2000 certified at this time. 6. Compliance to the Appraisal Criteria 6.1. Materials of Construction Separation Tank and Stand The Separation tank is manufactured from 304 Stainless Steel and is supported by a specifically engineered and constructed 304 Stainless Steel frame. (316 Stainless Steel Tanks are available as an option for installations in harsh or corrosive environments) Vertical-Tube Coalescing Pack The Vertical-Tube Coalescing Pack is constructed from Oleophilic Polypropylene, which provides increased efficiency and performance via its enhanced flow, phase separation characteristics and longevity Access Covers and Lids The lids that are used for the Clearmake product range are manufactured from 304 stainless steel and attached to the main body of the unit using stainless steel clips Internal Surface Coating The internal surface coating of the product range is not specially coated. 7. Performance Requirements 7.1. Process Description Clearmake separators are designed to reduce effluent oil content to less than 30 ppm. They use a Vertical-Tube Coalescing (VTC) pack, which utilises a block of vertically oriented 40 mm tubes that consist of bonded strands of spaced-apart polyethylene in a helical pattern. The waste stream enters the chamber and is forced through the open structure of the tubes. The solids are induced by gravity to the sludge hopper below and the waste stream continues a circuitous passage through the tube pack. Oil droplets coalesce on the surface of the tubes and then rise to the surface. The resultant build-up of oil on the surface is automatically skimmed off to the waste oil tank. The cleansed wastewater then flows under the underweir and over a final weir into a chamber 24 February 2010 Page 6

7 containing a filter bag before exiting through the outlet port. Design flow rate for systems fitted with a Mono CP11 pump is metres suction head. Design Flow rate for systems fitted with a diaphragm pump is 0.31 litres per 4.5 metres head. It is a requirement that appropriate Quick Break detergents & degreasers are being used. All other cleaners will cause the oily waste to emulsify and resist separation. Please refer to Clearmake for details on the appropriate products to be used 7.2. Effluent quality Clearmake has conducted sampling and testing in accordance with Sydney water requirements in 2003 at a Wash down Bay at Canterbury Timber One of the test reports have been made available and is included in Appendix B. The report is incomplete its inclusion in this Appraisal is noted as information only. A full trial is subject to a future works item (Part 16). 8. Applicability The product range is applicable to the following applications a. Mechanical repair workshops b. Panel beating workshops c. Vehicle detailing d. Motor wreckers e. Motor vehicle dealerships f. Hire Companies 24 February 2010 Page 7

8 g. Marinas h. Carwashes i. Lawnmower repairs 9. Specifications and Drawings The product specifications and drawings are included in Appendix C. 10. Warranty Clearmake Pty Ltd makes the following warranties of its products: PUMPS Manufacturer s warranty of 12 months from date of sale. j. Small engine repair shops The Mono pump operation and longevity is enhanced by the addition of a gooseneck in the pipework on the suction side of the pump to conserve a full reservoir of water within the pump cavity at all times. This arrangement is shown in the Mono Helical Rotor pump detail in the Typical Installation Layout drawing on page 13. The standard pump is not self-priming and requires a foot valve to be fitted to the base of the suction line to prevent it from losing prime when not running, if debris obstructs the foot valve or jams it open the pump will not prime itself. Care should therefore be taken during installation and maintenance procedures that the foot valve is placed and preserved accordingly SEPARATOR TANK, STAND & VERTICAL TUBE COALESCING 3 year warranty from date of sale. Note: The warranty on the separator tank is limited to normal applications where no corrosive elements are present. The tank is constructed of 304 stainless steel but is still susceptible to corrosion if exposed to certain substances. Check with Clearmake if in doubt as to your particular usage FLOAT SWITCH 1 Year manufacturer s warranty from date of sale OTHER COMPONENTS 1 Year manufacturer s warranty from date of sale. 11. Installation Requirements Installation Instructions a) Please consult your local trade waste/plumbing inspector before installing this separator to ensure that these instructions meet local requirements. b) ALWAYS USE LICENSED ELECTRICAL AND PLUMBING CONTRACTORS c) Place the separator into position and bolt the stand down. (ensure before you commence work that the concrete base you re installing this equipment on is suitable to hold the weight of the equipment.) Level the separator unit using the adjustable legs on the stand. Make sure the unit is level in both planes. NOTE: Read all instructions provided for this equipment and refer to all diagrams in this manual for assistance with installation. d) Connect the outlet pipe to sewer as per the Specification Drawing. 24 February 2010 Page 8

9 Note: e) Plumb the suction line to the pump using the correct diameter pipe as per the model specifications. Note: It is a requirement in some areas to provide sampling taps on the inlet and outlet pipes of the separator. f) The suction line must be terminated approx. 200 mm from the bottom of the holding tank and have a foot valve fitted (not supplied). Provide a barrel union in the suction line to permit the suction line to be withdrawn and serviced/inspected. g) Install a waste oil pipe from the oil skimmer outlet on the bottom of the tank to a 25 litre waste oil drum (available from Clearmake as an option). h) Fit the supplied gate valve (1) to the sludge hopper. Make sure it is closed before filling the separator. i) Fasten the pump to the concrete slab as shown in the installation drawing. Plumb the pump to the separator using barrel unions in the pipes either side of the pump to aid in servicing, and plug the pump into the electrical controller (available from Clearmake as an option). Note: Ensure that the water level in the holding tank never drops below the level of the suction line inlet causing the pump to lose prime. j) Install the float switch to deactivate the pump approx. 25 mm from the suction line inlet level. Fasten the float switch lead to the suction line with plastic cable ties with care taken to ensure that the float travel is not impeded in any way. Set the pumping range at approximately mm (this dimension may be increased or decreased to suit specific site applications and tank size). When nearly vertical the float switch will activate the pump. Ensure a minimum working volume of 500 litres in the pit as per Sydney Water guide lines. k) The electrical controller has a gland provided at its base to introduce the float lead inside the controller housing where low voltage terminals are provided to attach the float lead wires per the wiring instructions enclosed. Fill the separator tank with clean water and fill the pump priming chamber which is capped with a blue plug on the top of the black plastic stator housing. The controller typically has three settings Off, Manual and Auto and the pump can be started by switching to Manual and must be reset to Auto once the pump has been started and checked for proper operation. Note: Do not start the pump without enough water in the holding tank to cover the suction pipe inlet. l) Once the pump is running and the water level in the tank has stabilized, adjust the oil skimmer per instructions in the Oil Skimmer Details on the Typical Installation Layout drawing. Typically the top of the skimmer will be set at 3 mm above the level of the water with the pump running. a) The oil skimmer may require adjustment again after a film of oil has built up on the surface. b) A tap protected by a High Hazard Backflow Prevention Device (BFPD) is required within 5 metres of the apparatus. c) Refer local Authority for BFPD installation, testing and Agreement guidelines d) Any installation must be bunded and should have a minimum capacity of the system plus the storage drum Typical Schematic Installation The following schematic diagrams show the typical installation requirements for the product range described in this product appraisal report. 24 February 2010 Page 9

10 2007 Clearmake 24 February 2010 Page 10

11 2007 Clearmake 12. Operation and Maintenance Operation Once installed all models required no specific operational procedures. It is required however that the maintenance described in 12.2 must be routinely conducted Maintenance Maintenance intervals may need to be shortened depending on the amount of use and qualities of the influent. Clearmake recommends that Clearmake Separators be fully serviced at a minimal three monthly intervals by accredited service personnel. 24 February 2010 Page 11

12 a) DAILY/WEEKLY MAINTENANCE i) Clean all collection pits and silt traps. ii) Check waste oil tank level and arrange disposal of oil if necessary. iii) Visually inspect separator and remove any floating solids that may block tubes. iv) Check the filter bag to see if it is dirty or clogged. If it requires cleaning remove it by sliding it out of the track. Wash thoroughly and slide it back into place. Replace the bag if it is worn. Dispose of any waste water in accordance with Trade Waste policies v) Visually inspect discharge effluent and check that it appears to be clean. vi) Check the pump for normal operation and flow. vii) Check the holding tank sludge level and ensure the float switch is operating correctly. viii) Visually inspect all equipment for damage and correct operation. b) MONTHLY/QUARTERLY MAINTENANCE i) Perform those tasks listed in Daily/Weekly Maintenance. ii) Lower the oil skimmer below the water level to remove all oil from the water surface. iii) Drain the sludge hopper and dispose of correctly. (Usually to the holding tank) iv) Remove the Vertical-Tube Coalescing pack and clean thoroughly a pressure washer may be used. v) Clean out the separator thoroughly best achieved with a pressure washer. vi) Reinstall the Vertical-Tube Coalescing pack. vii) Fill the system with clean water. viii) Turn the power back on and check that the pump is primed and operating. 13. Identification Clearmake product authenticity is readily identified via reference to the compliance plate bearing the Clearmake proprietary information, and which is attached to the separator at the inlet end below the top rim. 24 February 2010 Page 12

13 14. Outcomes of WSAA Network Review Page 12 of the appraisal report - daily/weekly maintenance, item (iv) and monthly/quarterly maintenance, items, (iv) and (v) - It is important to provide advice to the reader on how the wastewater arising from those cleaning activities needs to be managed. An amendment has been made to the instructions to include the disposal of waste water from cleaning processes Pumping from a wet well (pump pit) not a silt sump should be a recommendation to the installer. 24 February 2010 Page 13

14 14.3. Oil water separators should be installed in a bunded area and connected back to the pump pit PVC not to be used in connection with the installation of an oil water separator Oil water separators to be connected to sewer through a typical industrial waste sample point WSAA Member and Field Reports At the time of publication a WSAA member field report was not available and this item has been referred as a future works and referenced in part 16 Future Works. 16. Future Works It is a requirement that within 2 years of the publication of this report that a report be provided for inclusion in this appraisal detailing the outcomes of effluent quality testing in accordance with WSA PS 810 (attached as an appendix) It is a requirement that within 12 months of the publication of this report that a WSAA member field report is provided for inclusion in this report. 17. Discussion Examination of all of the submitted documented material provides an expectation that the products described here in sourced and distributed by Clearmake Pty Ld are fit for purpose in the applications described in this report subject to future works items. 18. Report Recommendation It is recommended that WSAA Members and Associates, subject to any specific requirements of the Member or Associate, accept or authorise the Clearmake product range as detailed in this report for use in sewer networks provided design, installation, acceptance testing and commissioning and maintenance are in accordance with relevant WSAA Codes, WSAA Member Integrated Codes, and the manufacturer s requirements. 24 February 2010 Page 14

15 19. Disclaimer This Appraisal Report is issued by the Water Services Association of Australia Ld. on the understanding that : a) This appraisal applies to the product(s) as submitted. Any changes to the product(s) either minor or major shall void this appraisal. b) To maintain the recommendations of this appraisal any such changes shall be detailed and notified to the Product Appraisal Manager for consideration and review of the appraisal report and appropriate action. Appraisals and their recommendations will be the subject of continuous review dependent upon the satisfactory performance of products. c) WSAA reserves the right to undertake random audits of product manufacture and installation. Where products fail to maintain appraised performance requirements the appraisal and its recommendations may be modified and reissued. Appraisal reports will be reviewed and reissued at regular intervals not exceeding five (5) years. d) The following information explains a number of very important limits on your ability to rely on the information in this Product Appraisal Report. Please read it carefully and take it into account when considering the contents of this Product Appraisal Report e) Any inquiries regarding this report should be directed to the Appraisal Project Manager, Grant Leslie, Phone: grant.leslie@wsaa.asn.au Issue of Report This Product Appraisal Report (Report) has been published and/or prepared by the Water Services Association of Australia, Inc and nominated Project Manager and peer group of technical specialists (the Publishers). The Report has been prepared for use within Australia only by technical specialists that have expertise in the function of products such as those appraised in the Report (the Recipients). By accepting this Report, the Recipient acknowledges and represents to the Publisher[s] and each person involved in the preparation of the Report that the Recipient has understood and accepted the terms of this Disclaimer Limits on Reliance on Information and Recommendations Disclaimer of liability Neither the Publisher[s] nor any person involved in the preparation of the Report accept[s] any liability for any loss or damage suffered by any person however caused (including negligence or the omission by any person to do any thing) relating in any way to the Report or the product appraisal criteria underlying it. This includes (without limitation) any liability for any recommendation or information in the Report or any errors or omissions Need for independent assessment The information and any recommendation contained (expressly or by implication) in this Report are provided in good faith. However, you should treat the information as indicative only. You should not rely on that information or any such recommendation except to the extent that you reach an agreement to the contrary with the Publisher[s]. 24 February 2010 Page 15

16 This Report does not contain all information that a person might require for the purposes of assessing any product discussed or appraised within it (Product). The product appraisal criteria used in preparing this Report may not address all relevant aspects of the Product. Recipients should seek independent evidence of any matter which is material to their decisions in connection with an assessment of the Product and consul their own advisers for any technical information required. Any decision to use the Product should take into account the reliability of that independent evidence obtained by the Recipient regarding the Product. Recipients should also independently verify and assess the appropriateness of any recommendation in the Report, especially given that any recommendation will not take into account a Recipient's particular needs or circumstances. WSAA has not evaluated the extent of the product liability and professional indemnity insurance that the provider of the product maintains. Recipients should ensure that they evaluate the allocation of liability for product defects and any professional advice obtained in relation to the product or its specification including the requirements for product liability and professional indemnity insurance No updating Neither the Publisher[s] nor any person involved in the preparation of this Report [has][have] any obligation to notify you of any change in the information contained in this Report or of any new information concerning the Publisher[s] or the Product or any other matter No warranty The Publisher[s] do[es] not, in any way, warrant that steps have been taken to verify or audit the accuracy or completeness of the information in this Report, or the accuracy, completeness or reasonableness of any recommendation in this Report. 24 February 2010 Page 16

17 Appendix A Product Specifications 24 February 2010 Page 17

18 24 February 2010 Page 18

19 24 February 2010 Page 19

20 Appendix B Product Testing 24 February 2010 Page 20

21 24 February 2010 Page 21

22 24 February 2010 Page 22

23 Appendix C Product Specifications/Drawings Clearmake CB 1.0SS Drawing 24 February 2010 Page 23

24 24 February 2010 Page 24

25 24 February 2010 Page 25

26 Clearmake CL 3.0 SS DRAWING 24 February 2010 Page 26

27 Clearmake CL 3.0 SSD DRAWING 24 February 2010 Page 27

28 Appendix D Supplier Contacts Clearmake Pty Ltd 21 Project Ave Noosaville, Queensland 4566 Phone Fax February 2010 Page 28

29 Melbourne Office Level 8, 469 Latrobe Street Melbourne VIC 3000 PO Box Law Courts Post Office Melbourne VIC 8010 Phone: (03) Fax: (03) Sydney Office Suite 1, Level 30 9 Castlereagh St SYDNEY NSW 2000 GPO Box 915 Sydney NSW 2001 Phone: (02) Fax: (02) February 2010 Page 29

30 24 February 2010 Page 30