Lloyd s Register Type Approval System Test Specification Number GT04
|
|
- Alan Warren
- 5 years ago
- Views:
Transcription
1 Lloyd s Register Type Approval System Test Specification Number GT04 Gas Turbines Performance and test specifications for Gas Turbines to be used in Marine, Offshore and Industrial Applications 2004
2 Lloyd's Register Group Limited All rights reserved. Except as permitted under current legislation no part of this work may be photocopied, stored in a retrieval system, published, performed in public, adapted, broadcast, transmitted, recorded or reproduced in any form or by any means, without the prior permission of the copyright owner. Enquiries should be addressed to Lloyd's Register Group Limited, 71 Fenchurch Street, London, EC3M 4BS.
3 Foreword This Specification details the documentation, performance and tests required for the Lloyd's Register (LR) Approval of gas turbines for Marine, Offshore and Industrial applications. This test specification should be read in conjunction with the LR Type Approval System - Procedure TA02. Failure to comply with this requirement may render the test results unacceptable for the purposes of LR Type Approval. 1 Reference:
4 Table of Contents 1. Introduction General Phase Phase Details of Required Documentation Testing Procedures Visual Inspection and Certification Production Inspection and Certification Phase General Construction under Survey Alternative Quality Scheme of Inspection Reference:
5 1. Introduction 1.1. This specification is intended as an aid to assist a Producer seeking LR Type Approval of gas turbines for use in Marine, Offshore and Industrial applications and should be read in conjunction with the LR Type Approval System - Procedure TA02.` 1.2. Type Approval of gas turbines containing electrical and control components will be based on agreed performance and environmental tests. Assessment of Safety Systems fitted to such units will be carried out Electrical and control components may be required to meet the requirements of the LR Type Approval System - Test Specification No Separate Type Approval certificates are not issued for individual components on the basis of tests carried out on a composite product. 2. General 2.1. The Type Approval will be considered in three phases. During the Phase 1 review of the documentation and an appraisal of the design will be completed. The Type Testing and the issue of the appropriate certification will be carried out in the Phase 2. Phase 3 consists of the production inspection and certification Phase The submitted information will be forwarded by the Local LR office to the Type Approval Centre for consideration A document review will be conducted to determine such facts as product acceptability, compliance with relevant standards and LR s Rules, design appraisal, adequacy of proposed Type Test programme and relevance of previous certification and reports Phase Type Tests shall be carried out in accordance with the agreed test programme on a representative machine, to confirm that the performance provisions of the specified standard(s) are fulfilled. Type Tests are to be witnessed by the local LR representative, unless otherwise agreed in writing All test and measuring equipment shall be of proven accuracy, where appropriate traceable to a National or International standard of measurement Test area ambient conditions are to be monitored throughout testing Type Tests may be carried out at the manufacturer s works or at any establishment having suitable facilities acceptable to LR On completion of tests, a report shall be issued, identified by number and date, which accurately, clearly and unambiguously presents the test results and all other relevant information. The English language should be used Test reports shall be signed by the test personnel and countersigned, as verification of the results, by the LR or agreed independent representative witnessing the tests When the machine has been deemed to satisfy the procedures for LR Type Approval, a Type Approval Certificate will be authorised. 3 Reference:
6 3. Details of Required Documentation 3.1. Submission in triplicate of the following: Request for LR Type Approval via thelocal office, Detailed product specification, Relevant design drawings with materials specified, catalogues, data sheets, calculations and functional descriptions, Full details of: Sectional assembly drawing, Combustion chambers and heat exchangers, Rotors, bearings and couplings, Blades and blade attachments, Inlet and exhaust ducting, Securing arrangements, including details of resilient mounts where applicable, Control systems schematics, Fuel oil schematic, including controls and safety devices, Lubricating oil system schematic, Starting system schematic, Cooling water system schematic, where applicable Calculations of the critical speeds of blade and rotor vibration, giving full details of the basic assumptions Calculations concerning the amplitude and frequency of vibration associated with any resilient type mountings Proposed field of application and operational limitations Proposed Type Test programme, sufficiently detailed in order to demonstrate that the performance provisions of the specified standards may be fulfilled for acceptance, Certificates and reports for relevant tests previously obtained for the machine, Copies of the relevant standards where necessary. 4 Reference:
7 4. Testing Procedures 4.1. Generally, the requirements of BS 3135:1989 (ISO 2314:1989) will be used for the basis of the Test programme. The primary objective of the tests is to determine: Power output under specified operating conditions against ambient temperature (gas power, if only a gas generator is supplied), Thermal efficiency, heat rate or specific fuel consumption under specified operating conditions and, The adequacy of essential protective devices (i.e. emergency overspeed trip and flame failure trip, if installed) Additional tests to those detailed in 4.1 above, are: Performance of the following governing and protective systems; Constant speed regulation, Variable speed regulation, The gas turbine temperature control, gas turbine exhaust, turbine inlet or other limiting temperatures as applicable Low lubricating oil pressure, High lubricating oil temperature, High bearing temperature, Fuel supply pressure and, Handling characteristics, for example; Starting sequence, Starting reliability, Special starting characteristics, such as - black start, remote start, emergency start, dead load pick-up, alternative fuel start on dual fuel machines, starting power requirements, minimum self-sustaining speed determination and starting fuel consumption, Normal load pick-up, Time period for start-up and loading Amplitude and frequency of rotor vibration Amplitude and frequency of vibration associated with any resilient type mountings, (see above) Stack emissions, in accordance with a recognised test method, Exhaust mass flow and temperature (for waste heat recovery evaluation), Noise levels (generally in accordance with ISO 10494:1993), Dependent upon the field of application of the gas turbine, additional special testing may be required. This may include operating in excess of the maximum continuous rating and inclination tests. 5 Reference:
8 5. Visual Inspection and Certification 5.1. Following successful completion of Design Appraisal and Type Testing, the manufacturing facilities will be inspected to ensure that the appropriate procedures are in place in order to maintain conformity of manufacture for the five year life of the Type Approval Certificate Only when all outstanding points have been mutually resolved will the Type Approval Certificate be authorised and issued. 6. Production Inspection and Certification Phase General Type Approved gas turbines intended to be fitted into LR classed ships are to be surveyed at the manufacturer s works during their production The manufacturer has a choice of two production inspection and testing procedures. 6.2 Construction under Survey Individual gas turbine units are to be surveyed at the manufacturer s works. The Surveyors are to examine and test the materials and workmanship from the commencement of work until the final test of the gas turbine under full power working conditions in accordance with the rules. 6.3 Alternative Quality Scheme of Inspection Where gas turbines are manufactured as individual or series produced units a survey procedure based on quality assurance concepts utilising regular and systematic audits of the approved manufacturing and quality control processes and procedures as an alternative to the direct survey of individual items The procedure is detailed in LR Rules for Classification of Ships, Part 5, Chapter 1, Quality Assurance Scheme for Machinery. 6 Reference:
9 Lloyd s Register Group Limited 2018 Published by Lloyd s Register Group Limited Registered office (Reg. no ) 71 Fenchurch Street, London, EC3M 4BS United Kingdom
ShipRight Notice 1A for
ShipRight Notice 1A for Linked Supporting Services Planned Maintenance and Condition Monitoring, March 2013 The status of this ShipRight procedure is amended as shown and is now to be read in conjunction
More informationGuideline No.: E-03(201806) E-03 MOTORS. Issued date: June 7, China Classification Society
Guideline No.: E-03(201806) E-03 MOTORS Issued date: June 7, 2018 China Classification Society Foreword: This Guideline is a part of CCS Rules, which contains technical requirements, inspection and testing
More informationGuideline No.: E-04(201510) E-04 GENERATORS. Issued date: October 20,2015. China Classification Society
Guideline No.: E-04(201510) E-04 GENERATORS Issued date: October 20,2015 China Classification Society Foreword: This Guideline is a part of CCS Rules, which contains technical requirements, inspection
More informationGuideline No.: E-04(201610) E-04 GENERATORS. Issued date: October 28,2016. China Classification Society
Guideline No.: E-04(201610) E-04 GENERATORS Issued date: October 28,2016 China Classification Society Foreword: This Guideline is a part of CCS Rules, which contains technical requirements, inspection
More informationGuideline No.: E-03(201610) E-03 MOTORS. Issued date: October 28,2016. China Classification Society
Guideline No.: E-03(201610) E-03 MOTORS Issued date: October 28,2016 China Classification Society Foreword: This Guideline is a part of CCS Rules, which contains technical requirements, inspection and
More informationCLASSIFICATION NOTES. Type Testing Procedure for. Crankcase Explosion Relief Valves
CLASSIFICATION NOTES Type Testing Procedure for Crankcase Explosion Relief Valves Contents 1. Scope, Application 2. Recognized Standards 3. Purpose 4. Test Facilities 5. Explosion Test Process 6. Testing
More informationM-22 DUAL FUEL ENGINE
Guideline No.: M-22(201510) M-22 DUAL FUEL ENGINE Issued date: October 20,2015 China Classification Society Foreword: This Guide is a part of CCS Rules, which contains technical requirements, inspection
More informationSpecial Condition. Approval of Turbofan Engine Take-off Thrust at High Ambient Temperature (TOTHAT) rating.
Special Condition Approval of Turbofan Engine Take-off Thrust at High Ambient Temperature (TOTHAT) rating. This Special Condition is raised to support the approval of an additional rating for turbofan
More informationRESOLUTION MEPC.198(62) Adopted on 15 July GUIDELINES ADDRESSING ADDITIONAL ASPECTS TO THE NOx TECHNICAL CODE 2008 WITH REGARD TO
ANNEX 6 MEPC 62/24 Annex 6, page 1 2011 GUIDELINES ADDRESSING ADDITIONAL ASPECTS TO THE NO x TECHNICAL THE MARINE ENVIRONMENT PROTECTION COMMITTEE, RECALLING Article 38(a) of the Convention on the International
More information1.2 For the purpose of this UR, the following definitions apply: Low-Speed Engines means diesel engines having a rated speed of less than 300 rpm.
(Feb 2015) (Corr.1 June 2016) Type Testing of I.C. Engines 1. General 1.1 Type approval of I.C. engine types consists of drawing approval, specification approval, conformity of production, approval of
More informationCompatibility Between Electric Trains and Electrification Systems
Compatibility Between Electric Trains and Electrification Systems Synopsis Process for managing change that affects the compatibility between electric trains and electrification systems Submitted by Signatures
More informationRULES PUBLICATION NO. 98/P
RULES PUBLICATION NO. 98/P GUIDELINES REGARDING THE REQUIREMENTS FOR MARINE DIESEL ENGINES FITTED WITH NO X SELECTIVE CATALYTIC REDUCTION (SCR) SYSTEMS 2016 January Publications P (Additional Rule Requirements)
More informationDNVGL-CP-0110 Edition March 2016
CLASS PROGRAMME Type approval DNVGL-CP-0110 Edition March 2016 The electronic pdf version of this document, available free of charge from http://www.dnvgl.com, is the officially binding version. FOREWORD
More informationRapid Response. Lineside Signal Spacing. Railway Group Standard GK/RT0034 Issue Three Date September 1998
Rapid Response Railway Group Standard Lineside Signal Spacing Synopsis This Standard specifies the minimum distance that must be provided between the first signal displaying a cautionary aspect and the
More informationMARINE DIESEL ENGINES
ABCD LR NOx EMISSIONS CERTIFICATION OF MARINE DIESEL ENGINES April 2010 Lloyd's Register, 71 Fenchurch Street, London EC3M 4BS, UK ABCD Lloyd s Register 71 Fenchurch Street London EC3M 4BS Telephone +44
More informationRULES PUBLICATION NO. 98/P
RULES PUBLICATION NO. 98/P GUIDELINES REGARDING THE REQUIREMENTS FOR MARINE DIESEL ENGINES FITTED WITH NO X SELECTIVE CATALYTIC REDUCTION (SCR) SYSTEMS 2018 January Publications P (Additional Rule Requirements)
More informationBallast Water Management Surveyor Guidance An outline of Maritime NZ requirements of Surveyors for the purposes of Ballast Water Management
Ballast Water Management Surveyor Guidance An outline of Maritime NZ requirements of Surveyors for the purposes of Ballast Water Management Ballast water management surveyor guidance Page 1 of 9 Ballast
More informationRisk Management of Rail Vehicle Axle Bearings
Railway Group Standard Risk Management of Rail Vehicle Axle Bearings Synopsis This Railway Group Standard mandates that there shall be riskbased processes to minimise and detect failures of rail vehicle
More informationRULES PUBLICATION NO. 4/P IC ENGINES AND ENGINE COMPONENTS SURVEY AND CERTIFICATION July
RULES PUBLICATION NO. 4/P IC ENGINES AND ENGINE COMPONENTS SURVEY AND CERTIFICATION 2017 July Publications P (Additional Rule Requirements) issued by Polski Rejestr Statków complete or extend the Rules
More informationM-04 TRANSMISSION GEARS
Guideline No.: M-04(201510) M-04 TRANSMISSION GEARS Issued date: October 20,2015 China Classification Society Foreword: This Guide is a part of CCS Rules, which contains technical requirements, inspection
More informationGuideline No.: E-07(201610) E-07 TRANSFORMERS. Issued date: October 28,2016. China Classification Society
Guideline No.: E-07(201610) E-07 TRANSFORMERS Issued date: October 28,2016 China Classification Society Foreword: This Guide is a part of CCS Rules, which contains technical requirements, inspection and
More informationGuideline No.: E-07(201712) E-07 TRANSFORMERS. Issued date: December 26, China Classification Society
Guideline No.: E-07(201712) E-07 TRANSFORMERS Issued date: December 26, 2017 China Classification Society Foreword: This Guide is a part of CCS Rules, which contains technical requirements, inspection
More informationControl, Safe Use and Operation of Excavators, Loaders and Earth Moving Equipment
Control, Safe Use and Operation of Excavators, Loaders and Earth Moving Equipment Page 1 of 14 Part A Synopsis A standard detailing the requirements for the control, safe use and operation of excavators,
More informationNCC Leisure Battery Verification Scheme. Leisure Accommodation Vehicles
The UK trade body for the caravan, motorhome, caravan holiday and park home industry. NCC Leisure Battery Verification Scheme Leisure Accommodation Vehicles Page 1 of 11 1 Scope The NCC Battery Verification
More informationN-03 STEERING GEAR CONTROL SYSTEMS
Guideline No.: N-03(201510) N-03 STEERING GEAR CONTROL SYSTEMS Issued date: October 20,2015 China Classification Society Foreword: This Guideline is a part of CCS Rules, which contains technical requirements,
More informationBallast Water Management Surveyor checklist
Ballast Water Management Surveyor checklist Last updated: July 2017 This document is uncontrolled if printed, please refer to the Maritime New Zealand website for the latest version. Use this checklist
More informationAIR LUBRICATION SYSTEM INSTALLATION
Guide for Air Lubrication System Installation GUIDE FOR AIR LUBRICATION SYSTEM INSTALLATION OCTOBER 2018 American Bureau of Shipping Incorporated by Act of Legislature of the State of New York 1862 2018
More informationA MODEL SYLLABUS FOR THE TRAINING OF TECHNICIANS INVOLVED IN THE EXAMINATION, TESTING, MAINTENANCE AND REPAIR OF PETROLEUM ROAD TANKERS
A MODEL SYLLABUS FOR THE TRAINING OF TECHNICIANS INVOLVED IN THE EXAMINATION, TESTING, MAINTENANCE AND REPAIR OF PETROLEUM ROAD TANKERS A MODEL SYLLABUS FOR THE TRAINING OF TECHNICIANS INVOLVED IN THE
More informationCERTIFICATE OF FIRE APPROVAL
LR427.203.2 CERTIFICATE OF FIRE APPROVAL This is to certify that The product(s) detailed below will be accepted for compliance with the applicable Lloyd s Register Rules and Regulations for use on offshore
More informationGuideline No.: E-07(201501) E-07 TRANSFORMERS. Issued date: October 20,2015. China Classification Society
Guideline No.: E-07(201501) E-07 TRANSFORMERS Issued date: October 20,2015 China Classification Society Foreword: This Guide is a part of CCS Rules, which contains technical requirements, inspection and
More informationEU RO Mutual Recognition Technical Requirements
1. PRODUCT DESCRIPTION... 1 2. DESIGN EVALUATION... 2 3. PRODUCTION REQUIREMENTS... 6 4. MARKING REQUIREMENTS... 6 5. TYPE APPROVAL CERTIFICATE CONTENT... 7 6. APPROVAL DATE AND REVISION NUMBER... 7 7.
More informationDEPARTMENT OF TRADE AND INDUSTRY NO APRIL 2016
Trade and Industry, Department of/ Handel en Nywerheid, Departement van 438 National Regulator for Compulsory Specifications Act (5/2008): Amendments to the Compulsory Specification for Earth Leakage Protection
More informationMicrogeneration Installation Standard: MCS 023
Microgeneration Installation Standard: MCS 023 Additional Requirements for MCS Contractors to demonstrate PAS2030 equivalence for the installation of Microgeneration technologies. Issue 2.1 This Microgeneration
More informationImplementation procedure for certification and continued airworthiness of Beriev Be-200E and Be-200ES-E
1. Scope 1.1 The general process is described in the implementation procedure for design approvals of aircraft, engine and propeller from CIS and in the implementation procedure for design approvals of
More informationPrinciple Decision by the Central Experience Exchange Circle of the Notified Bodies and the GS Bodies according to the Product Safety Act ZEK
-GB-2017-01: Defining the requirements for a GS mark approval Principle Decision by the Central Experience Exchange Circle of the Notified Bodies and the GS Bodies according to the Product Safety Act about
More informationESS Lighting Instruction Pack Original Energy Saver
ESS Lighting Instruction Pack Original Energy Saver For projects completed: AFTER 1 July 2014 This Instruction Pack is designed to simplify the processing of Energy Savings Certificates for commercial
More informationAIR POLLUTION AND ENERGY EFFICIENCY. Guidelines for onboard sampling and the verification of the sulphur content of the fuel oil used on board ships
E MARINE ENVIRONMENT PROTECTION COMMITTEE 68th session Agenda item 3 MEPC 68/3/18 6 March 2015 Original: ENGLISH AIR POLLUTION AND ENERGY EFFICIENCY Guidelines for onboard sampling and the verification
More informationUnderstanding BS 1363 Amendment No.4
Intertek Hilton House, Corporation Street, Rugby, Warwickshire, CV21 2DN UK info.uk@intertek.com 01788 578435 www.intertek.com Introduction A new Amendment applying to several parts of the BS 1363 standard
More information-SQA- SCOTTISH QUALIFICATIONS AUTHORITY NATIONAL CERTIFICATE MODULE: UNIT SPECIFICATION GENERAL INFORMATION. -Module Number Session
-SQA- SCOTTISH QUALIFICATIONS AUTHORITY NATIONAL CERTIFICATE MODULE: UNIT SPECIFICATION GENERAL INFORMATION -Module Number- 2210034 -Session-1994-95 -Superclass- -Title- ZJ MOTOR VEHICLE INSPECTION: TACHOGRAPHS
More informationThree-phase motors for marine use
Three-phase motors for marine use Contents Product description 11/2 Overview of technical data 11/7 Series K.../W4.. for Premium Efficiency IE3 11/8 Series K.../WE.. for High Efficiency IE2 11/12 Series
More informationRecommendation for petroleum fuel treatment systems for marine diesel engines
(July 2017) Recommendation for petroleum fuel treatment systems for marine diesel engines I Recommendation for the treatment of fuel oil on board ships 1 Application The following requirements should apply
More informationPART XV Metering Systems SECTION 2 GUIDE TO GAS METERING SYSTEMS
THE INSTITUTE OF PETROLEUM PETROLEUM MEASUREMENT MANUAL PART XV Metering Systems SECTION 2 GUIDE TO GAS METERING SYSTEMS THE INSTITUTE OF PETROLEUM PETROLEUM MEASUREMENT MANUAL PART XV Metering Systems
More informationISO INTERNATIONAL STANDARD. Road vehicles Brake lining friction materials Friction behaviour assessment for automotive brake systems
INTERNATIONAL STANDARD ISO 26867 First edition 2009-07-01 Road vehicles Brake lining friction materials Friction behaviour assessment for automotive brake systems Véhicules routiers Matériaux de friction
More informationM-11 MARINE DIESEL ENGINE FUEL INJECTOR
Guideline No.M-11(201510) M-11 MARINE DIESEL ENGINE FUEL INJECTOR Issued date: 20 October 2015 China Classification Society Foreword This Guideline constitutes the CCS rules, and establishes the applicable
More informationControlling the Speed of Tilting Trains Through Curves
Controlling the Speed of Tilting Trains Through Curves Synopsis This document mandates the means by which Tilting Trains may be operated at higher speeds than nontilting trains around curves. Signatures
More informationCARES Technical Approval Report TA1C
CARES Technical Approval Report TA1C - 5057 Issue 1 LENTON Standard, Position, Parallel Bolt Couplers and Mechanical Anchor Assessment of the LENTON Standard, Standard Transition, Position, Parallel Bolt
More informationGREENER SHIPPING SUMMIT 2017
GREENER SHIPPING SUMMIT 2017 EU MRV Regulation Methods of Data Collection of Fuel Differences/Consequences/Evaluation of Methods Antonios Georgantzis 14 November 2017 Eugenides Foundation The EU MRV Timeline
More informationST. VINCENT AND THE GRENADINES
ST. VINCENT AND THE GRENADINES MARITIME ADMINISTRATION CIRCULAR N POL 022 FUEL OIL CONSUMPTION DATA COLLECTION SYSTEM Amendments to MARPOL Annex VI, MEPC.278(70) TO: APPLICABLE TO: EFFECTIVE AS FROM: SHIPOWNERS,
More informationReliable and Application specific. Slewing Drives for Wind Turbines
Reliable and Application specific 2 Powerful and versatile Yaw and pitch gearboxes based on proven technology: For almost 20 years Liebherr has been supplying highly reliable components to the wind industry.
More informationCertification Scheme
Certification Scheme Water-based surface-embedded heating and cooling systems in accordance with DIN EN 1264 (Version: November 2009) DIN CERTCO Alboinstraße 56 12103 Berlin Tel: +49 30 7562-1131 Fax:
More informationMicrogeneration Installation Standard: MCS
Microgeneration Installation Standard: MCS 001-01 MCS Contractor Certification Scheme Requirements Part 1: Requirements for MCS Contractors Issue 3.1 This Microgeneration Installation Standard is the property
More informationGUIDELINES FOR PORT STATE CONTROL UNDER MARPOL ANNEX VI
INTERNATIONAL MARITIME ORGANIZATION 4 ALBERT EMBANKMENT LONDON SE1 7SR Telephone: 020 7587 3152 Fax: 020 7587 3210 IMO E Ref. T5/1.08 MEPC/Circ.472 29 July 2005 GUIDELINES FOR PORT STATE CONTROL UNDER
More informationPart 5 Machinery Installations
2017 Rules for the Classification of Steel Ships Part 5 Machinery Installations 2017 Guidance Relating to the Rules for the Classification of Steel ships Part 5 Machinery Installations Rules Guidance 2017
More informationINCOMING INSPECTION DELEGATION GUIDELINES FOR ALENIA SUPPLIERS PROGRAM: ALL
INCOMING INSPECTION DELEGATION GUIDELINES FOR ALENIA SUPPLIERS PROGRAM: ALL THE CONTENT OF THIS DOCUMENT IS THE PROPERTY OF ALENIA AERONAUTICA S.p.A. THIS DOCUMENT IS SUPPLIED IN CONFIDENCE AND COMMERCIAL
More informationEU Mutual Recognition Technical Requirements
1. PRODUCT DESCRIPTION... 1 1.a General description of the product... 1 1.b Application limitations... 1 1.c Intended use... 2 1.d System context... 2 2. DESIGN EVALUATION... 2 2.a Engineering evaluation
More informationMINISTRY OF TRANSPORT, INFRASTRUCTURE, HOUSING, URBAN DEVELOPMENT AND PUBLIC WORKS
MINISTRY OF TRANSPORT, INFRASTRUCTURE, HOUSING, URBAN DEVELOPMENT AND PUBLIC WORKS STATE DEPARTMENT OF INFRASTRUCTURE KS 2295 IMPLEMENTATION GUIDELINE FOR LICENSING SPEED LIMITER SUPPLIERS 1. Preamble
More information.CITY & GUILDS. CROSS-BORDER..APPROVAL POLICY. Version 1.0 June 2015 For internal and external use
.CITY & GUILDS. CROSS-BORDER..APPROVAL POLICY. Version 1.0 June 2015 For internal and external use This is Version 1.0 of the City & Guilds Cross-border Approval Policy. It is the centre's responsibility
More informationMechanical Trainstop Systems
Mechanical Trainstop Systems Synopsis This document defines the functional requirements for mechanical trainstop systems and the requirements relating to their use on both track and trains. Signatures
More informationProposed Special Condition for limited Icing Clearances Applicable to Large Rotorcraft, CS 29 or equivalent. ISSUE 1
Proposed Special Condition for limited Icing Clearances Applicable to Large Rotorcraft, CS 29 or equivalent. ISSUE 1 Introductory note: The hereby presented Special Condition has been classified as important
More informationFUNCTIONAL SAFETY CERTIFICATE
FUNCTIONAL SAFETY CERTIFICATE This is to certify that the 1500 & 1600 Series 3/2 Single Pilot Operated Valves Manufactured by Rotork Midland Ltd Patrick Gregory Rd, Wolverhampton, West Midlands, WV11 3DZ.
More informationEquipotential Bonding of Rail Vehicles to Running Rail Potential
Railway Group Standard Equipotential Bonding of Rail Vehicles to Running Rail Potential Synopsis This standard mandates the requirements for equipotenial bonding of rail vehicles to comply with the Electricity
More informationDocuments for the approval of diesel engines
(1982) (Rev.1 1983) (Rev.2 1984) (Rev.3 1986) (Rev.4 1989) (Rev.5 1992) (Rev.6 Nov 2003) (Rev.7 May 2004) (Rev.8 Mar 2015 Complete Revision) (Rev.9 Dec 2015) (Corr.1 June 2016) (Corr.2 Nov 2016) Documents
More informationDER Commissioning Guidelines Community Scale PV Generation Interconnected Using Xcel Energy s Minnesota Section 10 Tariff Version 1.
Community Scale PV Generation Interconnected Using Xcel Energy s Minnesota Section 10 Tariff Version 1.3, 5/16/18 1.0 Scope This document is currently limited in scope to inverter interfaced PV installations
More informationOffshore manufacturing and fabrication: guidelines for heavy trailers (class TC and TD)
Offshore manufacturing and fabrication: guidelines for heavy trailers (class TC and TD) 1. INTRODUCTION This guideline has been prepared to alleviate confusion regarding the difference in Rule requirements
More informationREDUNDANT PROPULSION SHIPS RULES FOR CLASSIFICATION OF NEWBUILDINGS DET NORSKE VERITAS SPECIAL EQUIPMENT AND SYSTEMS ADDITIONAL CLASS PART 6 CHAPTER 2
RULES FOR CLASSIFICATION OF SHIPS NEWBUILDINGS SPECIAL EQUIPMENT AND SYSTEMS ADDITIONAL CLASS PART 6 CHAPTER 2 REDUNDANT PROPULSION JANUARY 2011 CONTENTS PAGE Sec. 1 General Requirements... 4 Sec. 2 System
More informationCARES Technical Approval Report TA1B
CARES Technical Approval Report TA1B - 5029 Issue 4 LENTON Standard, Standard Transition, Position, Position Transition, Parallel Bolt Couplers and Mechanical Anchors Assessment of the LENTON Standard,
More informationGuideline No.M-10(201510) M-10 Marine Diesel Engine Fuel Injection Pump
Guideline No.M-10(201510) M-10 Marine Diesel Engine Fuel Injection Pump Issued date: 20 th October, 2015 China Classification Society Foreword This Guideline is a part of CCS Rules, which contains technical
More informationBACS APPROVED BUREAU SCHEME SUPPORT GUIDELINES
BACS APPROVED BUREAU SCHEME SUPPORT GUIDELINES VERSION 8.2 May 2017 CONTENTS 1 DOCUMENT INFORMATION 4 1.1 VERSION HISTORY 4 1.2 DOCUMENT REVIEWERS 4 1.3 COPYRIGHT STATEMENT 4 2 CONFIDENTIALITY 4 3 INTRODUCTION
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD IEC 61325 First edition 1995-03 Insulators for overhead lines with a nominal voltage above 1 000 V Ceramic or glass insulator units for d.c. systems Definitions, test methods and
More informationBrochure. Synchronous generators for steam and gas turbines Proven generators reliable power
Brochure Synchronous generators for steam and gas turbines Proven generators reliable power We provide motors, generators and mechanical power transmission products, services and expertise to save energy
More informationBranding of Wheels,Tyres and Axles
Branding of Wheels,Tyres and Axles Signatures removed from electronic version Submitted by G A Clayton Nominated Responsible Manager Synopsis This standard details the branding requirements for all wheels,
More informationINFORMATION FOR OWNERS AND OPERATORS OF HEAVY TRUCKS AND BUSES
VEHICLE STANDARDS BULLETIN 2 BULLETIN TITLE MAXIMUM ROAD SPEED LIMITING FOR HEAVY TRUCKS AND BUSES INITIATED BY Vehicle Safety Standards DATE OF ISSUE October 1990 DATE OF EFFECT 1 January 1991 AN INFORMATION
More informationTHE INSTITUTE OF PETROLEUM PROCEDURES FOR THE RECLAIM OF DUTY ON RECOVERED VAPOUR AT DUTY SUSPENDED INSTALLATIONS
THE INSTITUTE OF PETROLEUM PROCEDURES FOR THE RECLAIM OF DUTY ON RECOVERED VAPOUR AT DUTY SUSPENDED INSTALLATIONS THE INSTITUTE OF PETROLEUM PROCEDURES FOR THE RECLAIM OF DUTY ON RECOVERED VAPOUR AT DUTY
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD IEC 60470 Second edition 1999-10 High-voltage alternating current contactors and contactor-based motor-starters Contacteurs pour courants alternatifs haute tension et démarreurs
More informationNot to be reproduced without permission Last date for receipt of BIS or used as STANDARD of comments 15 September 2011
For Comments Only Doc: TED 19(821)W July 2011 Draft Indian Standard SHIPBUILDING TESTING OF MARINE DIESEL ENGINES- CODE OF PRACTICE (Second Revision of IS 3979) Not to be reproduced without permission
More informationRESOLUTION MEPC.181(59) Adopted on 17 July GUIDELINES FOR PORT STATE CONTROL UNDER THE REVISED MARPOL ANNEX VI
MEPC 59/24/Add.1 RESOLUTION MEPC.181(59) THE MARINE ENVIRONMENT PROTECTION COMMITTEE, RECALLING Article 38(a) of the Convention on the International Maritime Organization concerning the functions of the
More informationVOLUNTARY CODE OF PRACTICE FOR ELECTROMAGNETIC COMPATIBILITY (EMC) OF MOTOR VEHICLES (13 October 2014)
FEDERAL CHAMBER OF AUTOMOTIVE INDUSTRIES VOLUNTARY CODE OF PRACTICE FOR ELECTROMAGNETIC COMPATIBILITY (EMC) OF MOTOR VEHICLES (13 October 2014) This code is prepared under the direction of the FCAl Board,
More informationM-24 OUTBORD ENGINES
Guideline No.: M-24(201510) M-24 OUTBORD ENGINES Issued date: October 20,2015 China Classification Society Foreword: This Guide is a part of CCS Rules, which contains technical requirements, inspection
More informationAssisted School Travel Program. Eligible Service Provider Request for Increased Run Capacity
Version 1.0 Assisted School Travel Program Eligible Service Provider Request for Increased Run Capacity Eligible Service Providers to the Department of Education and Communities Assisted School Travel
More informationControl, Safe Use and Operation of Road-Rail Plant
Control, Safe Use and Operation of Page 1 of 13 Part A Synopsis A Standard detailing the requirements for the control, safe use and operation of road-rail plant in the railway environment. Approval and
More informationUtilities (Technical Regulation) (Electricity Transmission Supply Code) Approval 2016 (No 1)*
Australian Capital Territory Utilities (Technical Regulation) (Electricity Transmission Supply Code) Approval 2016 (No 1)* Disallowable instrument DI2016 189 made under the Utilities Technical Regulation
More informationProposed New ISO Rules Section Version 2.0 Generating Unit Technical Requirements ( New ISO Rules Section Version 2.
Stakeholder Comment and Rationale Form AESO AUTHORITATIVE DOCUMENT PROCESS Stakeholder Consultation Draft 2012-11-29 Proposed New ISO Rules Section 502.5 Version 2.0 Generating Unit Technical Requirements
More informationJersey Harbour Authority Maritime House, St Helier, Jersey, JE1 1HB Tel: +44 (0) Website:
Jersey Harbour Authority Maritime House, St Helier, Jersey, JE1 1HB Tel: +44 (0)1534 447788 Email: jerseyharbours@ports.je Website: www.ports.je Vessel bunkering operations and the transfer of waste liquids
More informationAGN 041 Alternator Operating Speed
Application Guidance Notes: Technical Information from Cummins Generator Technologies AGN 041 Alternator Operating Speed INTRODUCTION AvK and STAMFORD synchronous a.c. generators (alternators) are designed
More informationMSC Guidelines for Fired Thermal Fluid Heaters Procedure Number: E1-28 Revision Date: 06/11/2014
References P. W. Gooding, Chief of Engineering Division a. 46 CFR Part 52 Power Boilers b. 46 CFR Part 54 Pressure Vessels c. 46 CFR Part 63 Automatic Auxiliary Boilers Contact Information If you have
More informationISO INTERNATIONAL STANDARD. Gas turbines Procurement Part 3: Design requirements
INTERNATIONAL STANDARD ISO 3977-3 Second edition 2004-08-15 Gas turbines Procurement Part 3: Design requirements Turbines à gaz Spécifications pour l'acquisition Partie 3: Exigences de conception Reference
More informationSHOCK TESTING OF EQUIPMENT AND SYSTEMS NAVAL APPLICATIONS
CLASSIFICATION NOTES No. 57.1 SHOCK TESTING OF EQUIPMENT AND SYSTEMS NAVAL APPLICATIONS JANUARY 2002 Veritasveien 1, N-1322 Høvik, Norway Tel.: +47 67 57 99 00 Fax: +47 67 57 99 11 FOREWORD is an autonomous
More informationIMO UNIFIED INTERPRETATIONS TO SOLAS CHAPTER II-2, THE FSS CODE AND RELATED FIRE TEST PROCEDURES
INTERNATIONAL MARITIME ORGANIZATION E IMO SUB-COMMITTEE ON FIRE PROTECTION 48th session Agenda item 3 FP 48/3/2 10 October 2003 Original: ENGLISH UNIFIED INTERPRETATIONS TO SOLAS CHAPTER II-2, THE FSS
More informationEconomic and Social Council
United Nations Economic and Social Council ECE/TRANS/WP.29/2017/50 Distr.: General 23 December 2016 Original: English Economic Commission for Europe Inland Transport Committee World Forum for Harmonization
More informationTechnical Information
Subject Equipment for the Singapore flag vessels To whom it may concern Technical Information No. TEC-1045 Date 28 August 2015 Regarding the requirement for equipment installed Singapore registered ships
More informationCenterwide System Level Procedure
5.ARC.0004.2 1 of 10 REVISION HISTORY REV Description of Change Author Effective Date 0 Initial Release J. Hanratty 7/17/98 1 Clarifications based on 7/98 DNV Audit and 6/98 Internal Audit (see DCR 98-029).
More informationTHE INSTITUTE OF PETROLEUM GUIDELINES FOR THE DESIGN AND PROTECTION OF PRESSURE SYSTEMS TO WITHSTAND SEVERE FIRES
THE INSTITUTE OF PETROLEUM GUIDELINES FOR THE DESIGN AND PROTECTION OF PRESSURE SYSTEMS TO WITHSTAND SEVERE FIRES THE INSTITUTE OF PETROLEUM GUIDELINES FOR THE DESIGN AND PROTECTION OF PRESSURE SYSTEMS
More informationTOPAS 2130A (Draft v3)
TOPAS 2130A (Draft v3) Revision Date Scope Authorised by A (v1) 10/10/17 Draft A (v2) 11/11/17 Draft A (v3) 15/12/17 Draft Traffic Open Products And Specifications Limited 2017. This document is the property
More informationIMILV01 Carry out routine light vehicle maintenance
IMILV01 Carry out routine light vehicle maintenance Overview This NOS is about conducting routine maintenance, adjustment and replacement activities as part of the periodic servicing of light vehicles.
More informationE/ECE/324/Rev.2/Add.102/Rev.1 E/ECE/TRANS/505/Rev.2/Add.102/Rev.1
30 August 2011 Agreement Concerning the adoption of uniform technical prescriptions for wheeled vehicles, equipment and parts which can be fitted and/or be used on wheeled vehicles and the conditions for
More informationRUBBER BELLOWS TYPE 1A & 1S SERIES
RUBBER BELLOWS TYPE 1A & 1S SERIES Description: Vibracoustics Ltd Reiflexa Bellows are made from various elastomers reinforced with high tensile textile or steel cords to provide the flexible elements
More informationMSC Guidelines for Fired Thermal Fluid Heaters Procedure Number: E1-28 Revision Date: April 20, 2018
References C. J. Robuck, LCDR, Chief, Engineering Division a. 46 CFR Part 52 Power Boilers b. 46 CFR Part 54 Pressure Vessels c. 46 CFR Part 63 Automatic Auxiliary Boilers Contact Information If you have
More information13 th December Title: The Fire Resistance Performance Of Doorsets When Fitted With Perko Powermatic R100 Jamb Mounted Concealed Door Closers
Warringtonfire Holmesfield Road Warrington WA1 2DS T: +44 (0)1925 655 116 F: +44 (0)1925 655 419 info.warrington@warringtonfire.com warringtonfire.com Title: The Fire Resistance Performance Of Doorsets
More informationISO INTERNATIONAL STANDARD. Bi-directional and multi-directional fork-lift trucks Stability tests
INTERNATIONAL STANDARD ISO 15794 First edition 2001-02-15 Bi-directional and multi-directional fork-lift trucks Stability tests Chariots élévateurs à fourche bi-directionnelle et multi-directionnelle Essais
More informationTYPE APPROVAL CERTIFICATE
TYPE APPROVAL CERTIFICATE Certificate No: P-15161 File No: 791.70 Job Id: 262.1-008998-2 This is to certify: That the Flexible Hoses of Non-Metallic Material with Permanently Fitted Couplings with type
More information