EU Mutual Recognition Technical Requirements
|
|
- Camron Norton
- 5 years ago
- Views:
Transcription
1 1. PRODUCT DESCRIPTION a General description of the product b Application limitations c Intended use d System context DESIGN EVALUATION a Engineering evaluation requirements b Type testing requirements PRODUCTION REQUIREMENTS a General requirements MARKING REQUIREMENTS TYPE APPROVAL CERTIFICATE CONTENT APPROVAL DATE AND REVISION NUMBER BACKGROUND INFORMATION / REFERENCES PRODUCT DESCRIPTION 1.a General description of the product These Technical Requirements apply to devices, commonly known as spark arresters, which prevent the emission of sparks by diesel engines, boilers and equipment containing sources of ignition and which could lead to the ignition of flammable materials. 1.b Application limitations Limiting engine ratings shall be defined at type approval stage and not to be exceeded. Where an exhaust system also includes other features which significantly restrict the flow of gases, e.g. flame traps, restrictive silencers, etc., or the engine manufacturer specifies an unusually low back pressure limit, or where specific noise reduction levels are specified, the type and size of the spark arrester has to be chosen according to manufacturer's instructions. Manufacturer's installation guidelines shall be followed. All the above limitations shall be recorded in the Type Approval Certificate. Page 1 of 5
2 1.c Intended use Spark arrester intended for use in the exhaust line of diesel engines, boilers and equipment containing sources of ignition installed onboard ships or offshore units. 1.d System context Exhaust systems for diesel engines, boilers and equipment containing sources of ignition, onboard ships or offshore units. 2. DESIGN EVALUATION 2.a Engineering evaluation requirements 2.a i. Technical Requirements The spark arrester shall comply with the requirements defined by one of the standards below in agreement with the Manufacturer: (a) European Norm EN , (b) SAE standards J350, J342 and J997, (c) Other standards assessed to be equivalent with standards a) and b). 2.a.ii. Technical documents to be submitted For all documentation, the English language shall be used. The following documentation shall be submitted by the Manufacturer before type testing: (a) Technical data and characteristics including limiting engine ratings, (b) Identification of different variants of sub-types, (c) Construction drawings, (d) Dimensions and tolerances, (e) Instructions on fitting and assembly, Page 2 of 5
3 (f) Materials specification, (g) Proposed test program and test schedule as per one of the standards and norms defined in 2.a.i, (h) Description of the test specimen(s) including serial numbers, (i) Relevant information on the testing facility, (j) Installation manual and maintenance requirements. The following documentation shall be submitted by the Manufacturer after the completion of type testing: (a) Reports of tests as per one of the standards and norms defined in 2.a.i, including details of test laboratory, place and date of tests, (b) Builder installation manual and guidelines for maintenance. 2.b Type testing requirements The spark arrester shall be tested as required in standards and norms mentioned in 2.a.i. All tests should be carried out with one selected test specimen. In cases where the tests are conducted at a Nationally Accredited Laboratory, the presence of the RO s surveyor may be omitted. 3. PRODUCTION REQUIREMENTS 3.a General requirements Refer to EU RO Product Quality Assurance (PQA)" procedure (Annex VI of EU RO Framework Document for the Mutual Recognition of Type Approval.. Page 3 of 5
4 4. MARKING REQUIREMENTS The spark arrester, for the purposes of type approval, shall be permanently marked with: (a) manufacturer's name or trade mark (b) type number (c) serial number. 5. TYPE APPROVAL CERTIFICATE CONTENT The validity of the certificate shall be 5 years given the condition that: (a) The design and manufacture remain unmodified from the initial process, (b) The specified regulations or standards are not modified during the validity period, (c) The product remains satisfactory in service. The Type Approval Certificate shall clearly state all other complementary clauses that are part of the conditions of issue. The Type approval certificate shall be issued including the following information: (a) Company name and address, (b) General product designation (type and model), (c) Test standards with the date and/or number of edition, (d) Onboard environmental conditions considered, (e) Remarks like limitations, (f) Test reports with identification number and date, (g) Manufacturer s documentation identification number for the product or series with date, (h) Date of issue and date of expiry, (i) Place of Issue. Page 4 of 5
5 6. APPROVAL DATE AND REVISION NUMBER Date Revision Comment Accepted by Advisory Board Reference to EU RO Framework Document for the Mutual Recognition of Type Approval. 7. BACKGROUND INFORMATION / REFERENCES a) SAE standard J342 Spark Arrester Test Procedure for Large Size Engines. b) SAE standard J350 Spark Arrester Test Procedure for Medium Size Engines. c) SAE standard J997 Spark Arrester Test Carbon. d) European Norm EN Reciprocating internal combustion engines. Safety requirements for design and construction of engines for use in potentially explosive atmospheres. Group II engines for use in flammable gas and vapour atmospheres. e) EU RO Framework Document for the Mutual Recognition of Type Approval. End of Document Page 5 of 5
EU RO Mutual Recognition Technical Requirements
1. PRODUCT DESCRIPTION... 1 2. DESIGN EVALUATION... 2 3. PRODUCTION REQUIREMENTS... 5 4. MARKING REQUIREMENTS... 6 5. TYPE APPROVAL CERTIFICATE CONTENT... 6 6. APPROVAL DATE AND REVISION NUMBER... 6 7.
More informationEU RO Mutual Recognition Technical Requirements
1. PRODUCT DESCRIPTION... 1 2. DESIGN EVALUATION... 2 3. PRODUCTION REQUIREMENTS... 6 4. MARKING REQUIREMENTS... 6 5. TYPE APPROVAL CERTIFICATE CONTENT... 7 6. APPROVAL DATE AND REVISION NUMBER... 7 7.
More informationVOLUNTARY CODE OF PRACTICE FOR ELECTROMAGNETIC COMPATIBILITY (EMC) OF MOTOR VEHICLES (13 October 2014)
FEDERAL CHAMBER OF AUTOMOTIVE INDUSTRIES VOLUNTARY CODE OF PRACTICE FOR ELECTROMAGNETIC COMPATIBILITY (EMC) OF MOTOR VEHICLES (13 October 2014) This code is prepared under the direction of the FCAl Board,
More informationAIR POLLUTION AND ENERGY EFFICIENCY. Guidelines for onboard sampling and the verification of the sulphur content of the fuel oil used on board ships
E MARINE ENVIRONMENT PROTECTION COMMITTEE 68th session Agenda item 3 MEPC 68/3/18 6 March 2015 Original: ENGLISH AIR POLLUTION AND ENERGY EFFICIENCY Guidelines for onboard sampling and the verification
More informationSKN_N0106AnnexJ_R2. Annex J - Specific requirements for PVT collector Certification. 1. Introduction and definition
Annex J - Specific requirements for PVT collector Certification 1. Introduction and definition PVT collectors (named hybrid collectors in ISO 9806) generate heat and electric power at the same time. They
More informationDEPARTMENT OF TRADE AND INDUSTRY NO APRIL 2016
Trade and Industry, Department of/ Handel en Nywerheid, Departement van 438 National Regulator for Compulsory Specifications Act (5/2008): Amendments to the Compulsory Specification for Earth Leakage Protection
More informationGuideline No.: E-07(201712) E-07 TRANSFORMERS. Issued date: December 26, China Classification Society
Guideline No.: E-07(201712) E-07 TRANSFORMERS Issued date: December 26, 2017 China Classification Society Foreword: This Guide is a part of CCS Rules, which contains technical requirements, inspection
More informationGuideline No.: E-07(201610) E-07 TRANSFORMERS. Issued date: October 28,2016. China Classification Society
Guideline No.: E-07(201610) E-07 TRANSFORMERS Issued date: October 28,2016 China Classification Society Foreword: This Guide is a part of CCS Rules, which contains technical requirements, inspection and
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 16852 Second edition 2016-10-15 Flame arresters Performance requirements, test methods and limits for use Arrête-flammes Exigences de performance, méthodes d essai et limites
More informationCLASSIFICATION NOTES. Type Testing Procedure for. Crankcase Explosion Relief Valves
CLASSIFICATION NOTES Type Testing Procedure for Crankcase Explosion Relief Valves Contents 1. Scope, Application 2. Recognized Standards 3. Purpose 4. Test Facilities 5. Explosion Test Process 6. Testing
More informationPOLLUTION PREVENTION AND RESPONSE. Application of more than one engine operational profile ("multi-map") under the NOx Technical Code 2008
E MARINE ENVIRONMENT PROTECTION COMMITTEE 71st session Agenda item 9 MEPC 71/INF.21 27 April 2017 ENGLISH ONLY POLLUTION PREVENTION AND RESPONSE Application of more than one engine operational profile
More informationAGREEMENT. done at Vienna on 13 November Addendum 1: Rule No. 1. Revision 1
6 March 2007 AGREEMENT CONCERNING THE ADOPTION OF UNIFORM CONDITIONS FOR PERIODICAL TECHNICAL INSPECTIONS OF WHEELED VEHICLES AND THE RECIPROCAL RECOGNITION OF SUCH INSPECTIONS done at Vienna on 13 November
More informationEU-Mexico Free Trade Agreement EU TEXTUAL PROPOSAL
This document contains an EU proposal for a legal text on an annex on motor vehicles and equipment and parts thereof to the Trade in Goods chapter in the Trade Part of a possible modernised EU-Mexico Association
More informationIMO UNIFIED INTERPRETATIONS TO SOLAS CHAPTER II-2, THE FSS CODE AND RELATED FIRE TEST PROCEDURES
INTERNATIONAL MARITIME ORGANIZATION E IMO SUB-COMMITTEE ON FIRE PROTECTION 48th session Agenda item 3 FP 48/3/2 10 October 2003 Original: ENGLISH UNIFIED INTERPRETATIONS TO SOLAS CHAPTER II-2, THE FSS
More informationGuideline No.: E-07(201501) E-07 TRANSFORMERS. Issued date: October 20,2015. China Classification Society
Guideline No.: E-07(201501) E-07 TRANSFORMERS Issued date: October 20,2015 China Classification Society Foreword: This Guide is a part of CCS Rules, which contains technical requirements, inspection and
More informationIMO. REVIEW OF MARPOL ANNEX VI AND THE NO x TECHNICAL CODE. Proposal to harmonize a record book of engine parameters
INTERNATIONAL MARITIME ORGANIZATION E IMO SUB-COMMITTEE ON BULK LIQUIDS AND GASES 11th session Agenda item 5 BLG 11/5/7 12 January 2007 Original: ENGLISH REVIEW OF MARPOL VI AND THE NO x TECHNICAL CODE
More informationA SIMPLIFIED TEST PROCEDURES FOR KNAPSACK (OPERATOR- CARRIED) SPRAYERS CHAN CHEE WAN
A SIMPLIFIED TEST PROCEDURES FOR KNAPSACK (OPERATOR- CARRIED) SPRAYERS CHAN CHEE WAN CONTENTS I. INTRODUCTION II. ANTAM (ESCAP -CSAM) APPROVED STATUS III. GUIDELINES ON STANDARDS AND TEST PROCEDURES IV.
More informationTITLE: SPECIFICATION FOR BENCH VICE & BENCH GRINDER TABLE OF CONTENTS. 0.1 Circulation List. 0.2 Amendment Record
Page 1 of 10 TABLE OF CONTENTS 0.1 Circulation List 0.2 Amendment Record FOREWORD 1. SCOPE 2. REFERENCES 3. TERMS AND DEFINITIONS 4. REQUIREMENTS 5. TESTS AND INSPECTION 6. MARKING AND PACKING 7. DEMONSTRATION
More informationFlameproof Enclosures
Flameproof Enclosures The range comprises many standard sizes of enclosures manufactured in stainless steel 316L and/or in painted carbon steel. The enclosures allow for utilization of standard electrical
More informationMethod Implementation Document (MID)
Method Implementation Document (MID) BS EN 14792:2005 Stationary source emissions Determination of mass concentration of nitrogen oxides (NOx) Reference method: Chemiluminescence Environment Agency Version
More informationSystems and Arrangement for Meeting Regulations in Emission Control Areas (ECA)
RULES FOR CLASSIFICATION OF Ships PART 6 CHAPTER 25 NEWBUILDINGS SPECIAL EQUIPMENT AND SYSTEMS ADDITIONAL CLASS Systems and Arrangement for Meeting Regulations in Emission Control Areas (ECA) JANUARY 2010
More informationATEX LABELLING FOR MOTORS AND GEAR UNITS
ATEX LABELLING FOR MOTORS AND GEAR UNITS EN ATEX INFORMATION GAS AND DUST COMPLETE DRIVE SOLUTIONS FROM A SINGLE SOURCE RELIABLE n Reliable products n Coordinated components n NORD's own development and
More informationReg Consolidated to Supplement 2 (Revision 3 Amendment 2)Replacement Brake Linings
[PREAMBLE] E/ECE/324/Rev.1/Add.89/Rev.3/Amend 2-E/ECE/TRANS/505/Rev.1/Add.89/Rev.3/Amend 2 3 February 2015 AGREEMENT CONCERNING THE ADOPTION OF UNIFORM TECHNICAL PRESCRIPTIONS FOR WHEELED VEHICLES, EQUIPMENT
More informationJoint Meeting Standards Working Group Report of the second meeting, Bern, March 2003
Joint Meeting of the RID Safety Committee INF. 48 and the Working Party on the Transport of Dangerous Goods (Bern, 24-28 March 2003) Joint Meeting Standards Working Group Report of the second meeting,
More informationDate of hosting on website: 26 th October 2017 Last date for comments: 25 th November 2017
Date of hosting on website: 26 th October 2017 Last date for comments: 25 th November 2017 CHECK LIST FOR PREPARING AUTOMOTIVE INDUSTRY STANDARD Draft AIS-146/D0 : Requirements applying to stands fitted
More informationM-22 DUAL FUEL ENGINE
Guideline No.: M-22(201510) M-22 DUAL FUEL ENGINE Issued date: October 20,2015 China Classification Society Foreword: This Guide is a part of CCS Rules, which contains technical requirements, inspection
More informationE/ECE/324/Rev.2/Add.104/Rev.2 E/ECE/TRANS/505/Rev.2/Add.104/Rev.2
28 September 2011 Agreement Concerning the adoption of uniform technical prescriptions for wheeled vehicles, equipment and parts which can be fitted and/or be used on wheeled vehicles and the conditions
More informationDNVGL-CP-0110 Edition March 2016
CLASS PROGRAMME Type approval DNVGL-CP-0110 Edition March 2016 The electronic pdf version of this document, available free of charge from http://www.dnvgl.com, is the officially binding version. FOREWORD
More informationGuideline No.: E-03(201806) E-03 MOTORS. Issued date: June 7, China Classification Society
Guideline No.: E-03(201806) E-03 MOTORS Issued date: June 7, 2018 China Classification Society Foreword: This Guideline is a part of CCS Rules, which contains technical requirements, inspection and testing
More informationE/ECE/324/Rev.2/Add.114/Rev.1 E/ECE/TRANS/505/Rev.2/Add.114/Rev.1
21 August 2013 Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles, Equipment and Parts which can be Fitted and/or be Used on Wheeled Vehicles and the Conditions for
More informationRide-on lawnmowers (combustion engine powered)
Compliance Guide Rev.2.3 Edition 04/2018 Ride-on lawnmowers (combustion engine powered) This guide is intended to help market surveillance authorities with the checking of conformity of combustion engine
More informationRESOLUTION MEPC.181(59) Adopted on 17 July GUIDELINES FOR PORT STATE CONTROL UNDER THE REVISED MARPOL ANNEX VI
MEPC 59/24/Add.1 RESOLUTION MEPC.181(59) THE MARINE ENVIRONMENT PROTECTION COMMITTEE, RECALLING Article 38(a) of the Convention on the International Maritime Organization concerning the functions of the
More informationIndia Comments on EPPR-13-09e
India Comments on EPPR-13-09e ECE/TRANS/WP.29/GRPE/2016/0X Proposal for a new Global technical regulation on the measurement procedure for two- or three-wheeled motor vehicles equipped with a combustion
More informationTillers Motor hoes (combustion engine powered)
Compliance Guide Rev.2.1, Edition 04/2018 This guide is intended to help market surveillance authorities with the checking of conformity of combustion engine powered brush-cutters and grass trimmers in
More informationLloyd s Register Type Approval System Test Specification Number GT04
Lloyd s Register Type Approval System Test Specification Number GT04 Gas Turbines Performance and test specifications for Gas Turbines to be used in Marine, Offshore and Industrial Applications 2004 Lloyd's
More informationA brief guide for identification of non-compliant construction machinery. Is this. Compactor / Roller compliant with European legislation?
A brief guide for identification of non-compliant construction machinery Is this Compactor / Roller compliant with European legislation? Introduction Construction equipment placed on the EU market for
More informationCarl Stuart Ltd. Tallaght Business Park, Whitestown, Dublin 24. Calibration Laboratory Registration number: 270C
Tallaght Business Park, Whitestown, Dublin 24 Calibration Laboratory Registration number: 270C is accredited by the Irish National Board (INAB) to undertake calibration as detailed in the Schedule bearing
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 8178-4 Second edition 2007-12-15 Reciprocating internal combustion engines Exhaust emission measurement Part 4: Steady-state test cycles for different engine applications Moteurs
More informationE/ECE/324/Rev.2/Add.102/Rev.1 E/ECE/TRANS/505/Rev.2/Add.102/Rev.1
30 August 2011 Agreement Concerning the adoption of uniform technical prescriptions for wheeled vehicles, equipment and parts which can be fitted and/or be used on wheeled vehicles and the conditions for
More informationInformation Sheet. concerning the Issuing of Multi-stage Typeapprovals in accordance with Directive 2007/46/EC (MMT) Version: March 2016.
Information Sheet concerning the Issuing of Multi-stage Typeapprovals in accordance with Directive 2007/46/EC (MMT) Version: March 2016 Typeapproval Contents Page 1 Introduction... 4 2 Definitions...
More informationECE/RCTE/CONF/4/Add.1/Rev.2
ECE/RCTE/CONF/4/Add.1/Rev.2 8 May 2018 Agreement Concerning the adoption of uniform conditions for periodical technical inspections of wheeled vehicles and the reciprocal recognition of such inspections
More informationANNEX MOTOR VEHICLES AND MOTOR VEHICLES' PARTS. Article 1. General Provisions
ANNEX MOTOR VEHICLES AND MOTOR VEHICLES' PARTS Article 1 General Provisions 1. This Annex shall apply to motor vehicles in UNECE vehicle regulations' category M1 as well as parts and equipment regulated
More informationGuideline No.: E-03(201610) E-03 MOTORS. Issued date: October 28,2016. China Classification Society
Guideline No.: E-03(201610) E-03 MOTORS Issued date: October 28,2016 China Classification Society Foreword: This Guideline is a part of CCS Rules, which contains technical requirements, inspection and
More informationImplementation procedure for certification and continued airworthiness of Beriev Be-200E and Be-200ES-E
1. Scope 1.1 The general process is described in the implementation procedure for design approvals of aircraft, engine and propeller from CIS and in the implementation procedure for design approvals of
More informationTHE ENERGY EFFICIENCY ACT. Regulations made by the Minister under section 23 of the Energy Efficiency Act
Government Notice No... of 2016 THE ENERGY EFFICIENCY ACT Regulations made by the Minister under section 23 of the Energy Efficiency Act 1. These regulations may be cited as the Energy Efficiency (Labelling
More informationInformation Bulletin. Fire Pump Battery Failures. Version 1.1 Approved for release August 2011
Version 1.1 Approved for release August 21 1.0 Purpose Statement The purpose of this is to raise awareness amongst stakeholders about concerning industry trends associated with batteries supporting fire
More informationLaboratory Evaluation Report for: Backflow Preventer for Beverage Dispensing Equipment
American Society of Sanitary Engineering Seal (Certification) Program Laboratory Evaluation Report for: Backflow Preventer for Beverage Dispensing Equipment Tested under ASSE Standard 1022 ASSE: 2003 ANSI:
More informationAMENDMENTS TO BUNKER DELIVERY NOTE TO PERMIT THE SUPPLY OF FUEL OIL NOT IN COMPLIANCE WITH REGULATION 14 OF MARPOL ANNEX VI
E SUB-COMMITTEE ON POLLUTION PREVENTION AND RESPONSE 3rd session Agenda item 10 PPR 3/10 10 December 2015 Original: ENGLISH AMENDMENTS TO BUNKER DELIVERY NOTE TO PERMIT THE SUPPLY OF FUEL OIL NOT IN COMPLIANCE
More informationTHE UNITED KINGDOM VEHICLE APPROVAL AUTHORITY EU TYPE-APPROVAL CERTIFICATE
Communication concerning: EU type-approval extension of EU type-approval refusal of EU type-approval withdrawal of EU type-approval THE UNITED KINGDOM VEHICLE APPROVAL AUTHORITY EU TYPE-APPROVAL CERTIFICATE
More informationE/ECE/324/Rev.1/Add.38/Rev.2 E/ECE/TRANS/505/Rev.1/Add.38/Rev.2
E/ECE/324/Rev.1/Add.38/Rev.2 24 January 2018 Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Equipment and Parts which can be Fitted and/or be
More informationKBA Kraftfahrt-Bundesamt
Kraftfahrt-Bundesamt (Federal Motor Transport Authority) Your central provider of services and information concerning vehicles and their users Vehicle Technology - Information Sheet on Approvals for New
More informationETSI EN V1.2.1 ( ) Harmonized European Standard (Telecommunications series)
EN 301 783-2 V1.2.1 (2010-07) Harmonized European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Commercially available amateur
More informationMattest (Ireland) Ltd
Unit 18 University Hall, Sarsfield Road, Wilton, Cork Registration number: 289T is accredited by the Irish National Board (INAB) to undertake testing as detailed in the Schedule bearing the Registration
More informationProposal for a new UNECE regulation on recyclability of motor vehicles
Transmitted by OICA Informal document No. GRPE-65-39 (65 th GRPE, 15-18 January 2013, agenda item 15) Proposal for a new UNECE regulation on recyclability of motor vehicles Informal Document GRPE-65-21
More informationINTERNATIONAL AIR POLLUTION PREVENTION CERTIFICATE. GOVERNMENTOFmELAND
INTERNATIONAL AIR POLLUTION PREVENTION CERTIFICATE No LDROIMMO/20150224110303 Issued under the provisions of the Protocol of 1997, as amended by resolution MEPC.176(58) in 2008, to amend the International
More informationANNEX MOTOR VEHICLES AND EQUIPMENT AND PARTS THEREOF. Article 1. Definitions
ANNEX MOTOR VEHICLES AND EQUIPMENT AND PARTS THEREOF Article 1 Definitions 1. For the purpose of this Annex, the following definitions apply: (a) WP.29 means the World Forum for Harmonisation of Vehicle
More informationSERIES 670E End-of-Line Deflagration Flame Arrester
SERIES 670E PROTECTOSEAL CAUTION: If any questions arise concerning the proper installation or maintenance of our products, please contact Protectoseal or one of our Authorized Representatives. When installing
More informationGASEOUS FUELS SAFETY ASPECTS
Ship Efficiency Conference by The German Society for Maritime Technology Hamburg, 29 September 2009 GASEOUS FUELS SAFETY ASPECTS Bruno DABOUIS 1. REGULATORY CONTEXT 2. USE OF GAS FUEL ENGINES ON SHIPS
More informationISO :2015/DAM 1
DRAFT AMENDMENT ISO 19973-2:2015/DAM 1 ISO/TC 131 Voting begins on: 2018-01-15 Secretariat: ANSI Voting terminates on: 2018-04-09 Pneumatic fluid power Assessment of component reliability by testing Part
More informationE/ECE/324/Rev.2/Add.106/Rev.6/Amend.5 E/ECE/TRANS/505/Rev.2/Add.106/Rev.6/Amend.5
28 October 2016 Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles, Equipment and Parts which can be Fitted and/or be Used on Wheeled Vehicles and the Conditions
More informationUNITED STATES DEPARTMENT OF AGRICULTURE FOREST SERVICE STANDARD FOR SPARK ARRESTERS. FOR INTERNAL COMBUSTION ENGINEs
Standard 5100-1d February 2013 Superseding 5100-1c September 1997 UNITED STATES DEPARTMENT OF AGRICULTURE FOREST SERVICE STANDARD FOR SPARK ARRESTERS FOR INTERNAL COMBUSTION ENGINEs Beneficial comments
More informationProposed Special Condition for limited Icing Clearances Applicable to Large Rotorcraft, CS 29 or equivalent. ISSUE 1
Proposed Special Condition for limited Icing Clearances Applicable to Large Rotorcraft, CS 29 or equivalent. ISSUE 1 Introductory note: The hereby presented Special Condition has been classified as important
More informationIrving Oil Whitegate Refinery Limited
Irving Oil Whitegate Refinery Limited Whitegate, Midleton, Co. Cork Testing Laboratory Registration number: 258T is accredited by the Irish National Board (INAB) to undertake testing as detailed in the
More informationICOMIA Global Conformity Guideline for ISO and ABYC Standards. Guideline Number 8 Ventilation of fuel systems
ICOMIA Global Conformity Guideline for ISO and ABYC Standards sponsored by ABYC, BMF, ICOMIA, IMCI, and NMMA Guideline Number 8 Ventilation of fuel systems 1. PURPOSE These documents were created by an
More information(Text with EEA relevance)
L 150/10 COMMISSION REGULATION (EU) 2015/924 of 8 June 2015 amending Regulation (EU) No 321/2013 concerning the technical specification for interoperability relating to the rolling stock freight wagons
More informationCETOP POSITION PAPER PP 07
CETOP POSITION PAPER PP 07 MACHINERY DIRECTIVE 2006/42/EC Valid since 26 th May 2010 CETOP General Secretariat Lyoner Straße 18 D-60528 Frankfurt am Main Phone: +49 69 6603 1201 Fax: +49 69 6603 2201 E-mail:
More information020: 2013 CEB SPECIFICATION MINIATURE CIRCUIT BREAKER (MCB)
020: 2013 CEB SPECIFICATION MINIATURE CIRCUIT BREAKER (MCB) CEYLON ELECTRICITY BOARD SRI LANKA Telephone: +94 11 232 0953 Fax: +94 11 232 3935 CONTENTS Page 1.0 Scope 3 2.0 System Parameters 3 3.0 Service
More informationPHILIPPINE DISTRIBUTION CODE 2017 EDITION
PHILIPPINE DISTRIBUTION CODE 2017 EDITION PDC 2017- Background Revised the PDC 2001 Starts of revision in 2010 April 18 and 24, 2012 conducted a series of expository presentation for Visayas and Mindanao
More informationChina Regulatory Update
Requirements on Marine Engine NOx Emission Limit for Imported Ships Engaged in Chinese Domestic Trading and Chinese Flag International Vessels Engaged in Domestic Waterway Transportation Advisory Services
More informationNATIONAL REGULATOR FOR COMPULSORY SPECIFICATIONS ACT (ACT 5 OF 2008) AS AMENDED THROUGH THE LEGAL METROLOGY ACT (ACT 9 OF 2014)
284 No. 41473 GOVERNMENT GAZETTE, 2 MARCH 2018 N0.173 DEPARTMENT OF TRADE AND INDUSTRY 02 MARCH 2018 NATIONAL REGULATOR FOR COMPULSORY SPECIFICATIONS ACT (ACT 5 OF 2008) AS AMENDED THROUGH THE LEGAL METROLOGY
More informationRecommendation for petroleum fuel treatment systems for marine diesel engines
(July 2017) Recommendation for petroleum fuel treatment systems for marine diesel engines I Recommendation for the treatment of fuel oil on board ships 1 Application The following requirements should apply
More informationE/ECE/324/Rev.2/Add.115/Amend.3 E/ECE/TRANS/505/Rev.2/Add.115/Amend.3
7 July 2011 Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles, Equipment and Parts which can be Fitted and/or be Used on Wheeled Vehicles and the Conditions for
More informationThis document is meant purely as a documentation tool and the institutions do not assume any liability for its contents
1970L0156 EN 12.07.2007 025.001 1 This document is meant purely as a documentation tool and the institutions do not assume any liability for its contents B COUNCIL DIRECTIVE of 6 February 1970 on the approximation
More informationIGS-M-CH-051-1(0) Jan مصوب. Approved IGS. Molecular Sieve, Type 3A
IGS-M-CH-051-1(0) Jan. 2013 Approved مصوب شرآت ملي گازايران امورتدوين استانداردها IGS مشخصات فني براي خريد مولكولارسيو نوع 3A Molecular Sieve, Type 3A براي استفاده ازاستانداردها فقط به ا خرين نسخه منتشرشده
More informationTHE UNITED KINGDOM VEHICLE APPROVAL AUTHORITY
THE UNITED KINGDOM VEHICLE APPROVAL AUTHORITY COMMUNICATION CONCERNING THE APPROVAL GRANTED (1) TO A COMPONENT TYPE- APPROVAL CERTIFICATE IN RESPECT OF A NON-ORIGINAL EXHAUST SYSTEM FOR A TYPE OF MOTORCYCLE
More informationLenze ATEX-compliant gearboxes Gearboxes for use in potentially explosive atmospheres
Lenze ATEX-compliant gearboxes Gearboxes for use in potentially explosive atmospheres ATEX for drive technology The ATEX directive, which has been in force since July 1, 2003, has been introduced in an
More informationForm of IOPP Certificate and Supplements * INTERNATIONAL OIL POLLUTION PREVENTION CERTIFICATE
Appendix II Appendices to Annex I Form of IOPP Certificate and Supplements * Annex I INTERNATIONAL OIL POLLUTION PREVENTION CERTIFICATE (Note: This Certificate shall be supplemented by a Record of Construction
More informationCIRCULAR IMO FAQ on the sulphur limits in Emission Control Areas (ECAs)
12 JANUARY 2015 / C15001 CIRCULAR IMO FAQ on the sulphur limits in Emission Control Areas (ECAs) The International Maritime Organization (IMO) has published Frequently Asked Questions about sulphur limits
More informationGuideline Specifications for Replacement Brake Lining Assemblies and Drum Brake Linings for Power-Driven Vehicles and their Trailers
AUTOMOTIVE INDUSTRY STANDARD Guideline Specifications for Replacement Brake Lining Assemblies and Drum Brake Linings for Power-Driven Vehicles and their Trailers PRINTED BY THE AUTOMOTIVE RESEARCH ASSOCIATION
More informationRequirements for Alteration Design Registration Based on Fitness-for-Service
the pressure equipment safety authority Requirements for Based on Fitness-for-Service AB 535 Edition 1, Revision 0 - Issued 2018-06-27 Table of Contents FOREWORD... ii 1.0 INTRODUCTION... 1 2.0 DEFINITIONS
More informationPrinciple Decision by the Central Experience Exchange Circle of the Notified Bodies and the GS Bodies according to the Product Safety Act ZEK
-GB-2017-01: Defining the requirements for a GS mark approval Principle Decision by the Central Experience Exchange Circle of the Notified Bodies and the GS Bodies according to the Product Safety Act about
More informationEconomic and Social Council
United Nations Economic and Social Council ECE/TRANS/WP.1/2014/8/Rev.1 Distr.: General 8 January 2015 Original: English Economic Commission for Europe Inland Transport Committee Working Party on Road Traffic
More informationAnalysis of the tyre choice for noise emission measurements within the context of vehicle type approval and COP compared to on road operation
TEXTE 04/2010 Analysis of the tyre choice for noise emission measurements within the context of vehicle type approval and COP compared to on road operation Development of criteria for more efficient imbedding
More informationE/ECE/324/Add.5/Rev.6/Amend.2 E/ECE/TRANS/505/Add.5/Rev.6/Amend.2
5 December 2017 Agreement Concerning the Adoption of Harmonized Technical United Nations Regulations for Wheeled Vehicles, Equipment and Parts which can be Fitted and/or be Used on Wheeled Vehicles and
More informationGuideline for Parallel Grid Exit Point Connection 28/10/2010
Guideline for Parallel Grid Exit Point Connection 28/10/2010 Guideline for Parallel Grid Exit Point Connection Page 2 of 11 TABLE OF CONTENTS 1 PURPOSE... 3 1.1 Pupose of the document... 3 2 BACKGROUND
More informationSFI SPECIFICATION 35.1 EFFECTIVE: AUGUST 26, 2008 *
SFI SPECIFICATION 35.1 EFFECTIVE: AUGUST 26, 2008 * PRODUCT: Stock Car Steel Wheels 1.0 GENERAL INFORMATION 1.1 This SFI Specification establishes uniform test procedures and minimum standards for evaluating
More informationMAC Refrigerant Blend Cooperative Research Program --- Update --- Enrique Peral-Antúnez, RENAULT [ Chair person ]
MAC Refrigerant Blend Cooperative Research Program --- Update --- Enrique Peral-Antúnez, RENAULT [ Chair person ] 12TMSS-0022 October 31, 2012 Presentation Overview Background MRB CRP phase I : outcomes
More informationISBN SANS 342:2006 Edition 4 SOUTH AFRICAN NATIONAL STANDARD Automotive diesel fuel Published by Standards South Africa 1 dr lategan roa
ISBN 0-626-18752-4 SOUTH AFRICAN NATIONAL STANDARD Automotive diesel fuel Published by Standards South Africa 1 dr lategan road groenkloof private bag x191 pretoria 0001 tel: 012 428 7911 fax: 012 344
More informationLaboratory Evaluation Report for: Laboratory Faucet Backflow Preventer
American Society of Sanitary Engineering Seal (Certification) Program Laboratory Evaluation Report for: Laboratory Faucet Backflow Preventer Tested under ASSE Standard 1035 Revised: April, 2008 Laboratory
More informationInstruction Manual. Ex-Time 40 / 50
Instruction Manual Ex-Time 40 / 50 Contents 1. Introduction 13 2. Safety Advice 13 3. Faults and Damage 13-14 4. Safety Regulations 14 5. Ex-Data 14-15 6. Technical Data 15-16 7. Use and Application /
More informationSmall craft Electric propulsion system
INTERNATIONAL STANDARD ISO 16315 First edition 2016-03-15 Small craft Electric propulsion system Petits navires Système de propulsion électrique Reference number ISO 16315:2016(E) ISO 2016 ISO 16315:2016(E)
More informationUC Irvine Environmental Health & Safety SECTION: TITLE: Powered Industrial Truck (Forklift) Safety Program
UC Irvine Environmental Health & Safety SECTION: TITLE: Powered Industrial Truck (Forklift) Safety Program INITIATOR: Desirée Villarreal REVISION DATE: 10/17/2014 1. Program Description 2. Scope 3. Definitions
More informationCertification Scheme
Certification Scheme Barbecues burning solid fuels in accordance with DIN EN 1860-1 (Edition: August 2015) DIN CERTCO Alboinstrasse 56 12103 Berlin Tel.: +49 30 7562-1131 Fax: +49 30 7562-1141 E-mail:
More informationSFI SPECIFICATION 15.2 EFFECTIVE: MAY 1, 2008 *
SFI SPECIFICATION 15.2 EFFECTIVE: MAY 1, 2008 * PRODUCT: Drag Race Front Wheels 1.0 GENERAL INFORMATION 1.1 This SFI Specification establishes uniform test procedures and minimum standards for evaluating
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 13043 First edition 2011-04-15 Road vehicles Refrigerant systems used in mobile air conditioning systems (MAC) Safety requirements Véhicules routiers Systèmes réfrigérants utilisés
More informationGUIDELINES FOR PORT STATE CONTROL UNDER MARPOL ANNEX VI
INTERNATIONAL MARITIME ORGANIZATION 4 ALBERT EMBANKMENT LONDON SE1 7SR Telephone: 020 7587 3152 Fax: 020 7587 3210 IMO E Ref. T5/1.08 MEPC/Circ.472 29 July 2005 GUIDELINES FOR PORT STATE CONTROL UNDER
More informationUNITED STATES DEPARTMENT OF AGRICULTURE FOREST SERVICE STANDARD FOR SPARK ARRESTERS FOR INTERNAL COMBUSTION ENGINES
Standard 00-c September Superseding 00-b July UNITED STATES DEPARTMENT OF AGRICULTURE FOREST SERVICE STANDARD FOR SPARK ARRESTERS FOR INTERNAL COMBUSTION ENGINES. SCOPE... Scope. This standard establishes
More informationNot to be reproduced without permission Last date for receipt of BIS or used as STANDARD of comments 15 September 2011
For Comments Only Doc: TED 19(821)W July 2011 Draft Indian Standard SHIPBUILDING TESTING OF MARINE DIESEL ENGINES- CODE OF PRACTICE (Second Revision of IS 3979) Not to be reproduced without permission
More informationANNEX. to the. Commission Delegated Regulation (EU).../...
EUROPEAN COMMISSION Brussels, XXX [ ](2016) XXX draft ANNEX 1 ANNEX to the Commission Delegated Regulation (EU).../... amending Regulation (EU) No 540/2014 of the European Parliament and of the Council
More informationBSS Examination Record Form for Privately Owned and Managed Vessels
BSS Examination Record Form for Privately Owned and Managed Vessels [Edition 1.04 April 2013] Current boat name Former name Reg. number or index Length (m) Berths Hull material Hull colour Superstructure
More information