U-JOINT IDENTIFICATION

Transcription

1 U-JOINT IDENTIFICATION Bearing Quantity Type Page 4 Grooved Round Bearings Plain Round Bearings Grooved Round Bearings 2 Plain Round Bearings Welded Plate Round Bearings Welded Plate Round Bearings 2 Plain Round Bearings Knurled Round Bearings Slotted Round Bearings Wing Bearings Wing Bearings 2 Grooved Round Bearings Wing Bearings 2 Plain Round Bearings Wing Bearings 2 Welded Plate Round Bearings Popular Round Bearing Combination U-Joints U-JOINT IDENTIFICATION 1

2 D + = I Dimension D Bearing Diameter 0.788" (20.0mm) 0.886" (22.5mm) 0.938" ( 15 /16") " ( 15 /16") " ( 31 /32") 0.969" ( 31 /32") 0.985" (25.0mm) 1.000" (1") 1.024" (26.0mm) 1.044" (26.5mm) U-JOINTS WITH 4 GROOVED ROUND BEARINGS First, measure the outside diameters of two adjacent bearings to see if they are the same or different. Locate the diameter(s) in the first column using the smaller diameter first if the bearings are of two sizes. Second, remove the seals from two bearings opposite each other and re-install the bearings on the cross. Measure the distance from the inside edge of the lock ring groove on one bearing across the joint to the same point on the opposite bearing and write it down. See drawing above. Next measure the thickness of two lock rings together. Add this measurement to the first measurement and the total should be slightly less than the installed or yoke span dimension shown in the second column. If necessary, note the type and location of any lube fittings. Dimension I Includes Locks 1.496" (38.0mm) 1.496" (38.0mm) 1.485" (1 31 /64") 1.500" (1 1 /2") 1.500" (1 1 /2") 1.444" (1 29 /64") 1.444" (1 29 /64") 1.688" (1 11 /16") 1.717" (43.6mm) 1.732" (44.0mm) 1.719" (1 23 /32") 2.344" (2 11 /32") 1.843" (46.8mm) 2.205" (56.0mm) 1.988" (50.5mm) dangled lube fitting in center of cross k k G 515p Nissan Mazda Neapco 0600 Spicer 1000 Combination 338 x 861 Rockwell L6S Rockwell L6N Mechanics 1.5 Mazda Nissan Subaru Mechanics 1.75 Mechanics 2 Toyota Kia Mazda kplain bearing - needles. pspecial pocketed cross forging. 2

3 U-JOINTS WITH 4 GROOVED ROUND BEARINGS (Cont d) Dimension D Bearing Diameter 1.063" " (1 1 /16" / 27.0mm) 1.078" (1 5 /64") " (1 5 /64") " (1 1 /8") 1.103" (28.0mm) 1.125" (1 1 /8") 1.142" (29.0mm) 1.181" (30.0mm) 1.188" (1 3 /16") 1.231" (1 15 /64") 1.250" (1 1 /4") 1.260" (32.0mm) 1.310" (1 5 /16") 1.313" (1 5 /16") 1.339" (34.0mm) 1.375" (1 3 /8") 1.625" (1 5 /8") Dimension I Includes Locks 1.640" (1 41 /64") 1.818" 1.930" (49.0mm) 2.188" (2 3 /16") 2.343" (2 11 /32") 2.375" (2 3 /8") 2.375" x 2.781" 2.781" (2 25 /32") 2.125" (2 1 /8") 2.125" (2 1 /8") 2.625" (2 5 /8") 2.205" (56.0mm) 2.323" (59.0mm) 1.95" 2.125" (2 1 /8") 2.557" 2.625" (2 5 /8") 3.250" (3 1 /4") 2.047" (52.0mm) 2.087" (53.0mm) 2.835" (72.0mm) 2.290" (58.15mm) 2.993" (74.5mm) 2.188" (2 3 /16") dangled lube fitting in center of cross " (2 9 /16") 3.125" (3 1 /8") 2.000" (2") 3.000" (3") 2.14" 2.520" (64.0mm) 2.795" (2 51 /64") 3.313" (3 5 /16") 4.313" (4 5 /16") 2.205" (56.0mm) 2.915" (74.0mm) 3.000" (3") 3.702" (94.0mm) 3.780" (96.0mm) 4.375" (4 3 /8") Yesi Yesi G M H p 534G Yesi H iflush-type lube fitting in bearing. pspecial pocketed cross forging. Spicer 1210-WJ Rockwell L12N Nissan Spicer 1310-WJ Spicer 1310 Cleveland S55 Combination 429 x 433 Cleveland P55 Detroit 7260 Combination 315G x 316 Nissan Subaru Mazda Howse 14 Mechanics 2.5 Mechanics 3, Saginaw 44 American Axle 1344 Detroit 7290 Mechanics 4 Toyota Isuzu Mitsubishi Spicer 1310-WJ Cleveland R55 Cleveland O55 Detroit 5160 Detroit 5380 Howse 35 Toyota Rockwell 44R Mechanics 5 Mechanics 6 Walterscheid II American Axle 1485-WJ Spicer 1480-WJ (SPL55) American Axle 1555-WJ Spicer 1550-WJ (SPL70) Mechanics 7 3 U-JOINT IDENTIFICATION

4 D O 4 Dimension D Bearing Diameter 0.750" ( 3 /4") 0.788" (20.0mm) 0.868" (22.0mm) 0.875" ( 7 /8") 0.938" ( 15 /16") 0.945" (24.0mm) 0.985" (25.0mm) 1.005" (1") 1.024" (26.0mm) 1.063" " (1 1 /16" / 27.0mm) " (1 1 /16") " (1 1 /8") U-JOINTS WITH 4 PLAIN ROUND BEARINGS First, measure the outside diameters of two adjacent bearings to see if they are the same or different. Locate the diameter(s) in the first column using the smaller diameter first if the bearings are of two sizes. Second, remove the seals from two bearings opposite each other and re-install the bearings on the cross. Measure the overall dimension and locate it in the second column. te, the measured dimension should be slightly less than that shown. If necessary, note the type and location of any lube fittings. Dimension O Back to Back 1.906" (1 29 /32") 2.166" (55.0mm) 2.244" (57.0mm) 2.126" (54.0mm) 2.157" (54.8mm) 2.469" (2 15 /32") 2.910" (2 29 /32") 2.411" (2 13 /32") 2.490" (63.25mm) 2.524" (64.1mm) 3.012" (76.5mm) 3.910" (3 29 /32") 2.756" (70.0mm) 2.438" (2 7 /16") 2.650" (2 21 /32") 2.756" (70.0mm) 2.935" (2 15 /16") 3.218" x 3.622" bflush-type lube fitting in cross. clong lube fitting in cross. Yesb Yesi kl BL 341AG kl G AG BL BL 345 Use 430 Use 434 dangled lube fitting in center of cross. iflush-type lube fitting in bearing. 0400SG Kubota Toyota Bondioli 1 Walterscheid 2100 Rockwell L10N Rockwell 1FR Spicer 1100 Bondioli 2 Walterscheid 2200 Alfa Romeo Mitsubishi Rockwell 3DR Suzuki Spicer 1210 Saturn Bondioli 3 Walterscheid I Spicer 1300 Bondioli 4 Walterscheid 2300 Spicer 1310 Spicer 1310 x 1330 Spicer 1330 Visteon 1330 (Brg. OD 1.066") Ford 1310 Ford 1330 kplain bearing - needles. lknurling on portion of bearing.

5 U-JOINTS WITH 4 PLAIN ROUND BEARINGS (Cont d) Dimension D Bearing Diameter " (1 1 /16") " (1 3 /16") 1.123" (28.5mm) 1.125" (1 1 /8") " (1 1 /8") " (1 3 /16") 1.181" (30.0mm) 1.188" (1 3 /16") 1.250" (1 1 /4") 1.260" (32.0mm) 1.300" (33.0mm) 1.375" (1 3 /8") 1.378" (35.0mm) 1.417" (36.0mm) 1.531" (1 17 /32") 1.562" (1 9 /16") 1.575" (40.0mm) 1.615" (41.0mm) 1.625" (1 5 /8") 1.654" (42.0mm) 1.937" (1 15 /16") 2.165" (55.0mm) 2.186" (2 3 /16") 2.362" (60.0mm) clong lube fitting in cross. dangled lube fitting in center of cross. Dimension O Back to Back 3.218" x 3.622" 3.071" (78.0mm) 2.625" (2 5 /8") 3.268" (83.0mm) 3.150" (80.0mm) 3.228" (82.0mm) 4.178" 4.187" (4 3 /16") 3.210" 2.992" (76.0mm) 3.662" (93.0mm) 3.701" (94.0mm) 4.178" 4.187" (4 3 /16") 4.956" 4.965" 4.092" (103.9mm) 3.496" (88.8mm) 4.312" (4 5 /16") 4.562" (4 9 /16") 4.527" (115.0mm) 4.252" (108.0mm) 4.955" (126.0mm) 5.064" (5 1 /16") 5.590" (5 19 /32") 4.094" (104.0mm) 5.934" (5 15 /16") 6.456" (164.0mm) 8.092" (8 3 /32") 6.417" (163.0mm) Yesi etwo regular lube fittings in cross. iflush-type lube fitting in bearing BL A 331AG 330A A Rr 351AG 358A Rr t t Combination 369 x 331 Combination 354 x 331 Toyota Rockwell L14N Combination 434 x 331 ZF Bondioli 5 Carraro Spicer 1350 (SPL30) American Axle 1355 Bondioli 6 Walterscheid 220 American Axle 1415 Spicer 1410 (SPL36) Rockwell 35N Walterscheid 2400 Isuzu Bondioli 7 American Axle 1485 Spicer 1480 (SPL55) Rockwell 148N Bondioli 8 Walterscheid 240 American Axle 1555 Spicer 1550 (SPL70) Rockwell 155N Isuzu Walterscheid 2500 Rockwell 55N Hardy Spicer 1510 Hino Isuzu Bondioli 9 Spicer SPL90/100 (1590) Rockwell 750N Spicer 1650 Walterscheid 2600 Rockwell 850N Spicer SPL170 Spicer 1850 Spicer SPL250 rincludes thrust plates and lock rings. tour kit is designed to fit applications with one half round yoke and one full round yoke. U-JOINT IDENTIFICATION 5

6 O I U-JOINTS WITH 2 GROOVED 2 PLAIN ROUND BEARINGS Bearing Diameter Type 1.000" Grooved 1.000" Grooved 1.125" Plain 1.063" Grooved 1.063" Grooved 1.125" Plain 1.078" Grooved 1.078" Grooved 1.125" Plain Dimension I Includes Locks 1.719" (1 23 /32") 2.344" (2 11 /32") 2.344" (2 11 /32") 2.188" (2 3 /16") 2.344" (2 11 /32") 2.375" (2 3 /8") 2.781" (2 25 /32") 2.125" (2 1 /8") 2.125" (2 1 /8") 2.125" (2 1 /8") 2.560" (2 9 /16") 2.625" (2 5 /8") 2.560" ( " Plain 9 /16") 2.560" ( " Plain 9 /16") 1.231" Grooved 3.000" (3") 1.188" Plain bflush-type lube fitting in cross. Dimension O Without Locks 2.438" (2 7 /16") 4.187" (4 3 /16") Yesb Yesb Series Combination 514G x 437G Combination 507 x 369 Combination 507 x 430 Combination 365 x 369 Combination 368 x 369 Ford dangled lube fitting in center of cross. Combination 315G x 369 Combination 315G x 354 Combination 315G x 430 Combination 513 x 369 Combination 534G x 369 Combination 534G x 354 Combination 316 x 369 Combination 316 x 354 Combination 534G x 434 Combination 534G x 331 Combination 304 x 330 6

7 L D Dimension D Bearing Diameter 1.562" (1 9 /16") 1.812" (1 13 /16") 1.875" (1 7 /8") 1.937" (1 15 /16") 2.186" (2 3 /16") 2.312" (2 5 /16") D L D L U-JOINTS WITH 4 WELDED PLATE TYPE ROUND BEARINGS First, measure the bearing diameter and locate it in the first column. Second, measure the distance between two opposite plates and locate it in column two. If necessary, note the type and quantity of any lube fittings. etwo regular lube fittings in cross. Dimension L Between Plates 4.562" (4 9 /16") 5.937" (5 15 /16") 5.312" (5 5 /16") 6.094" (6 3 /32") 7.000" (7") 7.547" (7 35 /64") 8.094" (8 3 /32") 6.594" (6 19 /32") m Spicer 1500 Allmetal 700 Spicer 1610 Spicer 1710 Spicer 1760 Spicer 1810 Spicer 1880 Spicer 1800 moriginal production used one piece bearings. U-JOINT IDENTIFICATION U-JOINTS WITH 2 WELDED PLATE 2 PLAIN ROUND BEARINGS First, measure the bearing diameter and locate it in the first column. Second, measure the distance between two opposite plates and locate it in column two. Third, verify the Back to Back dimension in column three. Dimension D Bearing Diameter 1.875" (1 7 /8") 1.937" (1 15 /16") etwo regular lube fittings in cross. uincludes Clamp Kit. Dimension L Between Plates 5.312" (5 5 /16") 6.094" (6 3 /32") 7.000" (7") 7.547" (7 35 /64") Dimension L Back to Back 5.312" (5 5 /16") 6.187" (6 3 /16") 7.093" (7 3 /32") 7.640" (7 41 /64") 475or875u 476or876u 477or877u 478or878u Spicer 1610 Spicer 1710 Spicer 1760 Spicer

8 D L D L U-JOINTS WITH 4 KNURLED OR 4 SLOTTED ROUND BEARINGS First, measure the bearing diameter and locate it in the first column. Second, remove the seals from two bearings opposite each other and re-install the bearings on the cross. Measure the overall dimension and locate it in the second column. The actual figure should be slightly less than that shown. te if knurled or slotted. Dimension D Bearing Diameter 1.250" (1 1 /4") 1.375" (1 3 /8") 1.563" (1 9 /16") 1.937" (1 15 /16") 2.000" (2") Dimension L Back to Back 4.063" (4 1 /16") 4.188" (4 3 /16") 4.969" (4 31 /32") 4.563" (4 9 /16") 5.125" (5 1 /8") 5.937" (5 15 /16") dangled lube fitting in center of cross. Knurled Slotted Slotted Knurled Slotted Knurled Slotted Slotted Slotted Slotted 890 Use Use Use Rockwell 4N Cleveland D56 Cleveland U56 Rockwell 58N Rockwell 6N Rockwell 7N 8

9 U-JOINTS WITH WING BEARINGS A B C D U-JOINT IDENTIFICATION A Bolt Centers 1.31" 1.44" 1.44" 1.69" 1.69" 1.93" 1.94" 1.94" 1.94" 2.81" 2.81" SERIES IDENTIFICATION DIMENSIONS B Bolt Centers 2.34" 2.75" 3.44" 3.50" 4.50" 4.10" 4.25" 4.62" 6.88" 4.88" 6.62" C Pilot Dia. 3.12" 3.56" 4.25" 4.53" 5.53" 5.12" 5.31" 5.84" 8.12" 6.50" 8.25" D Swing Dia. 3.34" 3.81" 4.50" 4.78" 5.84" 5.70" 5.62" 6.22" 8.50" 6.88" 8.62" OE Series 2C 3C 4C 5C 6C * 58WB 7C 8C 8.5C 9C *Special for Sige Steering Axle 9

10 A B LWT Low Wing Threaded DWT Delta Wing Threaded LWD Low Wing Drilled HWD High Wing Drilled Dimension A Across Bearing 1.31" (1 5 /16") 1.44" (1 7 /16") 1.44" (1 7 /16") 1.69" (1 11 /16") Dimension B Across U-Joint 2.34" (2 11 /32") 2.75" (2 3 /4") 3.44" (3 7 /16") 3.50" (3 1 /2") clong lube fitting in cross. U-JOINTS WITH 4 WING BEARINGS Bearing Quantity Type 2 LWT 2 LWD 2 LWT 2 LWD 2 LWT 2 HWD 2 LWD 2 HWD 2 LWT 2 LWD 2 LWT 2 HWD 2 LWD 2 HWD 4 DWT 2 LWT 2 LWD 2 LWT 2 HWD 2 LWD 2 HWD Use o o 933o 993oq 558o oour production uses delta wing bearings in place of low wing bearings. q1¼" hole in center of cross. Mechanics 2C Mechanics 3C Mechanics 4C Mechanics 5C 10

11 Dimension A Across Bearing 1.69" (1 11 /16") 1.69" (1 11 /16") x 1.94" (1 15 /16") 1.93" (49mm) 1.94" (1 15 /16") 1.94" (1 15 /16") 1.94" (1 15 /16") 2.81" (2 13 /16") 2.81" (2 13 /16") Dimension B Across U-Joint 4.50" (4 1 /2") 4.50" (4 1 /2") x 4.62" (4 5 /8") 4.10" (104mm) 4.25" (4 1 /4") 4.62" (4 5 /8") 6.88" (6 7 /8") 4.88" (4 7 /8") 6.62" (6 5 /8") etwo regular lube fittings in cross. ftwo angled lube fittings in cross. gfour long lube fittings in cross. U-JOINTS WITH 4 WING BEARINGS (Cont d) Bearing Quantity Type 4 DWT n 2 LWT 2 LWD 2 LWT 2 HWD 2 DWT 2 HWD 2 LWT 2 LWT 2 LWT 2 HWD 2 HWD 2 LWT 2 HWD 2 HWD 4 DWT 2 DWT 2 HWD 4 DWT 2 LWT 2 LWD 2 LWT2 HWD 2 DWT 2 HWD 2 LWD 2 HWD 4 DWT 2 LWT 2 LWD 2 LWT2 HWD 2 DWT 2 HWD 4 DWT 2 LWT2 HWD 2 DWT 2 HWD 4 DWT 2 LWT2 HWD 2 DWT 2 HWD Yesg Yesf Yesf Yesf Yesf Yesf Yesf ntwo HWD bearings double keyed for CV. oour production uses delta wing bearings in place of low wing bearings. wincludes 12-pt cap screws. 560o o o 563o o 569o 924o w 894w 896w 570o o o 574o o 581o o o 583o o ow o o CBw o 792 Mechanics 6C Rockwell 62N Mechanics 6C x Mechanics 7C Sige Axle Rockwell 58WB Mechanics 6.5C Mechanics 7C Rockwell 72N Mechanics 8C Rockwell 82N Rockwell 85WB Mechanics 8.5C Mechanics 9C Rockwell 92N U-JOINT IDENTIFICATION 11

12 A D U-JOINTS WITH 2 WING BEARINGS 2 GROOVED ROUND BEARINGS Dimension A Across U-Joint 2.34" (2 11 /32") 2.75" (2 3 /4") 3.44" (3 7 /16") 3.50" (3 1 /2") 4.50" (4 1 /2") 4.62" (4 5 /8") 6.88" (6 7 /8") Bearing Diameter Type " Round Grooved 2 Low Wing Threaded 2 Low Wing Drilled " Round Grooved 2 Low Wing Threaded " Round Grooved 2 Low Wing Threaded 2 Low Wing Drilled " Round Grooved 2 Low Wing Threaded 2 Low Wing Drilled " Round Grooved 2 Low Wing Threaded " Round Grooved " Round Grooved clong lube fitting in cross G o 557o o Mechanics 2 Mechanics 3 Mechanics 4 Mechanics 5 Mechanics 6 Mechanics 7 Mechanics 8 oour production uses delta wing bearings in place of low wing bearings. 12

13 B C A D U-JOINTS WITH 2 WING BEARINGS 2 PLAIN ROUND BEARINGS or 2 WELDED PLATE ROUND BEARINGS MECHANICS ROCKWELL TO SPICER Bearing Type Diameter 2 Low Wing Threaded " Round Plain 2 Low Wing Threaded " Round Plain " Round Plain " Round Plain " Round Plain " Round Plain 2 Delta Wing Threaded " Round Plain " Round w/ Welded Plate " Round w/ Welded Plate etwo regular lube fittings in cross. Dimensions A B/C A 2.34" (2 11 /32") B 3.22" (3 7 /32") A 3.44" (3 7 /16") B 4.19" (4 3 /16") A 3.44" (3 7 /16") B 4.19" (4 3 /16") A 3.50" (3 1 /2") B 4.19" (4 3 /16") A 4.25" (4 1 /4") B 4.97" (4 31 /32") A 4.50" (4 1 /2") B 4.97" (4 31 /32") A 4.50" (4 1 /2") B 4.97" (4 31 /32") A 6.62" (6 5 /8") C 7.55" (7 35 /64") C 8.09" (8 3 /32") A D Mechanics 2C to Spicer 1310 Mechanics 4C to Spicer 1410 Mechanics 5C to Spicer 1480 Rockwell 58WB to Spicer 1550 Mechanics 6C to Spicer 1550 Mechanics 9C to Spicer 1810 Spicer 1880 U-JOINT IDENTIFICATION 13

14 POPULAR ROUND BEARING COMBINATION U-JOINTS O To find the correct combo joint, first determine the two individual joints to be combined, one at a time. Then put them in numerical order and refer to the first column. Grooved Plain I Combines U-Joints Combination U-Joint Bearing Diameter Type Dimension I Includes Locks Dimension O Without Locks " Grooved 3.00" " Plain 4.19" 315G 1.078" Grooved 2.12" " 3.22" " 315G " Grooved 2.12" 3.22" " Plain G " Plain 2.56" 3.22" G G " Grooved 1.188" Plain 2.12" 2.62" 2.56" 3.22" " 315G G " Grooved 1.188" Plain 2.12" 2.62" 2.56" 14