MANUFACTURER OF CONSTANT VELOCITY DRIVEAXLE COMPONENTS TH AVENUE ROCKFORD, ILLINOIS PHONE (815) FAX (815)

Transcription

1 TOOL DESIGNS & APPLICATIONS MANUFACTURER OF DRIVEAXLE COMPONENTS TH AVENUE, ILLINOIS PHONE (815) FAX (815)

2 Driveaxle Service Items B T CV Joint Bearing Removal Tool - Rotates The Race Allowing You To Remove The Bearings And Cage Inner Race Driver - Aids In Removing Internal Clip Type Joints Pneumatic Cut Off Tool - For Cutting Cage & Race Off Of Shaft B Pneumatic Cut Off Tool Replacement Wheel Side Cutters - For General Use GM Boot Seal Ring Installer Set - Used To Remove And Install The Boot Retaining Rings Found On Many Early GM Axles T Snap Ring Pliers - Use To Disengage Flat Faced Snap Rings C.V. Joint Disassembly Tool: Fits All FWD Inner Race Driver: For Removal of Joints With Frozen Internal Snap Rings Pneumatic Cut Off Tool: Joint Removal When Internal Circlips Lock Joint On Shaft Side Cutters: For General Use GM Boot Retainer InstallerSet: Heavy Duty Construction 2

3 Polishing Materials F M MT FT A Cartridge Rolls (Pkg of 10) - Fine Grit A Cartridge Rolls (Pkg of 10) - Course - 60 Grit Arbor For Cartridge Rolls F Buffing Wheel - Fine 8" OD - 1" Thick FT Buffing Wheel - Fine 6" OD - 1/2" Thick M Buffing Wheel - Medium 8" OD - 1" Thick MT Buffing Wheel - Medium 6" OD - 1/2" Thick /2" Arbor for 8" Wheel - (Set of Two) T 1/2" Arbor for 6" Wheel - (Set of Two) T Cartridge Roll & Arbor Assembly: For Polishing Ball Wear in Joints Buffing Wheel & Arbor Assembly: For Polishing Ball Wear in Races 3

4 Banding & Clamping Materials A A A T T Banding Tool - Used For Crimp Type Clamps Banding Tool - Used For Strap Type Clamps A Banding Tool (Racthet Design) - Used For Strap Type Clamps Stainless Steel Band Roll, 5/16 Wide A Stainless Steel Band Roll, 3/8 Wide Steel Band Clips - Pkg Of 100 Fits 5/16 Wide Band A Steel Band Clips - Pkg Of 100 Fits 3/8 Wide Band Band Straps - 11 Long, 5/16 Wide (Pkg Of 6) Band Straps - 16 Long, 3/8 Wide (Pkg Of 6) Band Straps - 21 Long, 3/8 Wide (Pkg Of 6) T Banding Tool: For Strap Type Clamps Banding Tool: For Crimp Type Clamps 4

5 Axle Shaft Removal and Installation Items T T Hub Installer Tool - Pulls The CV Thru The Hub On Subaru s T Deep Well Socket - 36mm Shaft Removal Tool - Allows You To Remove The Drivers Side Shaft Thru The Transaxle On Ford Applications OB Joint Punch - Remove The Joint From Hubs W/O Damaging The Stub (Ford And Subaru Applications) Hub Installer Tool - Pulls The CV Thru The Hub On Ford s T Deep Well Socket - 30mm Crossgroove Assembly T (Set) TB TA T Crossgroove Assembly Tool Set TA Crossgroove Assembly Tool - Beretta TB Crossgroove Assembly Tool - Lemans Auto TC Crossgroove Assembly Tool - Lemans Man & Bravada TC 5

6 Axle Shaft Removal and Installation Items For Re-Threading Damaged Outboard Housing Threads For Re-Threading Damaged Outboard Housing Threads From The Bottom Of The Threads Where They Can Be Easily Started S Thread Die Set - Includes Holder & 11 Solid Dies S Thread Die Set - Includes Holder & 11 Split Dies A Die (26 x 1.25mm) - GM (Eldorado & Toronado 67-78) AS Split Die (26 x 1.25mm) - Same as Above B Die (24 x 1.5mm) - Acura CL, (Legend 87-90) & Vigor, AMC Eagle, GM (Eldorado & Toronado 79-85), Honda (Accord & Prelude 90-up), Nissan (Stanza & Maxima 87-up), Subaru (exc. SVX, XT6 & Justy) BS Split Die (24 x 1.5mm) - Same as Above C Die (22 x 1.5mm) - Acura Integra, Audi 100 & 5000, BMW, Chrysler Domestic (exc. LH Body) & Imports, Diahatsu, Ford Contour, (Escort 92-96), Explorer, (Probe 88-98), T-Bird, Honda (Accord & Prelude 72-89), (Civic 80-98), Hyundai, Infinity G20, Kia Sephia, Lexus ES300, Mazda (MX6, Protege, ), Mitsubishi, Nissan (Altima, Pulsar, Sentra 87-97), Saab 9000, Subaru Forester, Legacy, Impreza, SVX & XT, Toyota Paseo & Previa CS Split Die (22 x 1.5mm) - Same as Above D Die (20 x 1.5mm) - Audi (exc. 5000), Eagle Medallion & Premier, Ford Aspire, Festiva, Probe 83-87, Taurus, Tempo & Windstar, GM With 3/4" Thread Dia 80-99, Mazda (MX6 & ), Renault, Subaru Justy 89-94, Volkswagen DS Split Die (20 x 1.5mm) - Same as Above E Die (24 x 2.0mm) - GM With 1" Thread Dia Including 4x4 Trucks ES Split Die (24 x 2.0mm) - Same as Above F Die (19 x 1.5mm) - Toyota Camry, Celica, Corolla & Tercel FS Split Die (19 x 1.5mm) - Same as Above G Die (22 x 1.0mm) - Datsun 310/F10, Mazda 929, Nissan (Pulsar, Sentra, Stanza 82-86) GS Split Die (22 x 1.0mm) - Same as Above H Thread Die Holder - Handle Only I Die (18 x 1.5mm) - Chevy Metro & Sprint, Geo Metro, Subaru Justy 87-88, Suzuki Swift IS Split Die (18 x 1.5mm) - Same as Above J Die (20 x 1.0mm) - GM LeMans & Spectrum, Geo Storm, Isuzu I-Mark, Impluse & Stylus JS Split Die (20 x 1.0mm) - Same as Above K Die (27 x 2.0mm) - Chrysler LH Body, GM (C Body & H Body 91-95) KS Split Die (27 x 2.0mm) - Same as Above L Die (26 x 1.5mm) - Acura Legend LS Split Die (26 x 1.5mm) - Same as Above 6

7 Benchwork : Air Vice Pneumatic Air Vise - (Foot pedal allows for hands free operation) Benchwork : Bushing Driver Benchwork : Seal Driver 176-E T 176-E6 Disk Joint Bushing Installer/Remover - (Toyota Previa Equipment Drive Shafts) 412-2T Seal Driver - for Late Model Spicer Design Stud Yokes - (Use On Dust Shield) 7

8 Benchwork : Crimping Fixtures & Repair Parts (100-14TA TN) TDS TBS TBF TAF TAS TA Crimping Fixture - ACI Chrysler, ACI Ford Tempo ( Boot Flange) TAF Replacement Flange Nut (Ea.) - Fits 1/2" Stud TAS Replacement Stud (Ea.) - 1/2" x 5" TB Crimping Fixture - Pontiac LeMans RH Auto Trans (712-3A Boot Assembly) TBF Replacement Flange Nut (Ea.) - Fits 5/8" Stud TBS Replacement Stud (Ea.) - 5/8" x 5" TC Crimping Fixture - Pontiac LeMans Manual Trans (712-4A Boot Assembly) TD Crimping Fixture - Nissan 300ZX Non-Turbo (280-4 Boot Assembly) TDS Replacement Stud (Ea.) - 5/8" x 6" TE Crimping Fixture - Mercedes Benz (230-4 Boot Assembly) TF Crimping Fixture - Ford Taurus ACI, Mercury Sable ACI ( Boot Flange) TG Crimping Fixture - Chevrolet Camaro, Oldsmobile Bravada, Pontiac Firebird (421-10A & C Boot Assemblies) TH Crimping Fixture - BMW 318i, BMW 325e (320-AS Boot Flange) TI Crimping Fixture - Lincoln Continental (714-4AS Boot Flange) TJ Crimping Fixture - Lexus GS300, LS400, SC300 & SC400 (550-4AS Boot Flange) TK Crimping Fixture - Mercedes Benz (220-3AS Boot Flange) TL Crimping Fixture - BMW 3 Series (804-4AS Boot Flange) TM Crimping Fixture - Ford Thunderbird, Mercury Cougar ( Boot Flange) TN Crimping Fixture - BMW Lineshafts 99mm Joints (804-10A Boot Assembly) 12

9 Installation Fixture: T PATENT PENDING Install ABS Rings Onto The Housing Without Damage. Ensure Proper Function Of Anti-Lock System. Holder And Rings For 45 Applications T RingMaster (Complete Set) TA Driver Ring - Installs , , A, B, C, A, B, A, C, , TB Driver Ring - Installs , , , D, , , , B, A, TC Driver Ring - Installs , , , , TD Driver Ring - Installs A, TE Driver Ring - Installs , A, , , , A, A, , B, D, , TF Driver Ring - Installs , A, A, C TG Driver Ring - Installs

10 Benchwork : CV Joint Press Hydraulic C.V. Joint Press - Removes All C.V. Joints With Internal Snap Rings Quickly And Easily. Rockford Joint Press Applies 12 Tons Of Pressure To The Joint With Its Wedge Design. Benchwork : CV Joint Press Repair Parts L1LW L1CB CS LIB L1CBB (A-U) L1SW A Replacement Collet - # B Replacement Collet - # C Replacement Collet - # CS Complete Set of Collets Includes Wood Storage Block D Replacement Collet - # E Replacement Collet - # F Replacement Collet - # G Replacement Collet - # H Replacement Collet - # I Replacement Collet - # LIB Shaft Retainer I Bolt Assembly L1CB Collet Block L1CBB Collet Block Bolt L1LW Large Wedge L1SW Small Wedge S Replacement Collet - # SRB Shaft Retainer Block - (Not Pictured) T Replacement Collet - # U Replacement Collet - # V Replacement Collet - #13 14

11 Assembly A T Transmission Support Bearing Installation Driver - (Except Chrysler) A Transmission Support Bearing Removal & Installation Tool - (Chrysler) T Carrier Bearing Assembly Tool - (Alliance/Encore - Left Shafts) Fixed Tripod Clip Installation Washer - (Alliance, Encore, Stanza) Fixed Tripod Clip Installation Washer - (Renault Le Car) Fixed Tripod Clip Installation Washer - (Toyota Tercel) Gauge Sets: For GM & Chrysler Axles using Saginaw Components 817-G 816-G 815-G 440-G 915-G 440-G Outboard Housing Gauge Set - OD of gauges increase in increments of.002 from the smallest gauge to the largest gauge. Used for 440 Series Parts 815-G Outboard Housing Gauge Set - OD of gauges increase in increments of.002 from the smallest gauge to the largest gauge. Used for 815 Series Parts 816-G Outboard Housing Gauge Set - OD of gauges increase in increments of.003 from the smallest gauge to the largest gauge. Used for 816 Series Parts 817-G Outboard Housing Gauge Set - OD of gauges increase in increments of.003 from the smallest gauge to the largest gauge. Used for 817 Series Parts 915-G Outboard Housing Gauge Set - OD of gauges increase in increments of.002 from the smallest gauge to the largest gauge. Used for 915 Series Parts 16

12 Extra Service Items B Replacement Spindle Nut & Spring Pins Kit - Assortment of 17 Spindle Nuts & Spring Pins (194-14, & Pins, C, S, , , , , , , , , , & Spindle Nuts) in a durable storage box Replacement Snap Ring Kit - Assortment of 18 popular internal snap rings (161-16, , , , , , , , , , , A, , , , , , , , , , A & ) in a durable storage box 915-7B5 C.V. Joint Grease oz. Ea. (Pkg. of 5) 915-7B C.V. Joint Grease oz. Ea. (Individual Packs) 17

13 C.V. Driveaxle Grease: Dura-Grease & Pump Materials 915-7C High-Temperature Grease Specially Formulated for use with the Rockford Dura-Boot 915-7A Designed for use with the Three Dura-Grease Container Sizes 915-7GP GP GP C.V. Joint Dura-Grease - 35 Lbs A C.V. Joint Dura-Grease Lbs B C.V. Joint Dura-Grease Oz. Bag (Not Pictured) 915-7C C.V. Joint Dura-Grease Lbs GP1 Grease Pump - Fits 400 Lbs. Barrels 915-7GP2 Grease Pump - Fits 120 Lbs. Barrels 915-7GP3 Grease Pump - Fits 35 Lbs. Buckets 915-7GPG Replacement Grease Pump Gun - (Not Pictured) 915-7GPH Replacement Grease Pump Hose - (Not Pictured) 915-7GPK Extra Gun Kit - (Not Pictured) 915-7GPZ Replacement Grease Pump "Z" Swivel - (Not Pictured) Driveaxle Boxes : For Shipping Axles To Your Customers BX23 BX36 BX43 BX23 25 Driveaxle Boxes - 23" x 6" x 6" BX36 25 Driveaxle Boxes - 36" x 4" x 5" BX43 25 Driveaxle Boxes - 43" x 4" x 5" 18