2/2-way Angle-Seat Control Valve with stainless steel design for media up to +180ºC, DN 13-50

Transcription

1 2/2-way ngle-seat Valve with stainless steel design for media up to +180ºC, DN Excellent control characteristic and high fl ow rates High cycle life Clean design for optimal use in hygienic environment Quality certifi cations available Type 2300 can be combined with... Type 8692/8693 Type 8694 Type 8696 Type 8137 Typ 8222 ositioner / rocess ler Top ositioner Top asic ositioner Top asic Radar level transmitter Conductivity transmitter In line with ürkert s philosophy for modular valves and sensors the construction of the 2300 angle-seat valve fulfils tough criteria for process environments. Unrivalled cycle life and sealing integrity is guaranteed by the proven self adjusting packing gland. The parabolic trim results in a flow characteristic approximately 35% larger than conventional control valves. It is available in either stainless steel on stainless steel or with a durable TFE seal for tight shut-off. The design enables the easy integration of automation modules whether they are digital electropneumatic positioner or process controller. The fully integrated system has a compact and smooth design, integrated pneumatic lines, I65/67/NEM4X protection class and superior chemical resistance. This system has been engineered for reliable accurate control in applications where high flow rate is an advantage. Technical data DN 13 to 50 ort s Threaded port acc. to Welded acc. to Clamp acc. to ody material material Cover lug sealing Seat leakage IEC 534-4/EN 1349 Media G 1/2 to G 2, NT 1/2 to NT 2, Rc 1/2 to Rc 2 EN ISO 1127, DIN S2, SME E, SMS 3008, S 4825 ISO 2852, SME E Stainless steel 316L S Stainless steel (316Ti) TFE/St.st. (TFE/stainless steel) and St.st./St.st. (stainless steel/stainless steel) Shut-off class IV for St.st./St.st. Shut-off class VI for TFE/St.st. Water, alcohol, oils, fuels, hydraulic fl uids, salt solution, alkali solutions, organic solvents, steam Viscosity max. 600 mm 2 /s acking gland TFE V-rings with spring compensation Medium temperature -10 to +180 ºC (max C for TFE/St.st. sealing recommended) mbient temperature 0 to +60 ºC medium Compressed air ilot pressure 5.5 to 7 bar ilot air ports ush-in connector for external ø 6 mm or 1/4 tube Installation s required, preferably with actuator in upright position Content Valve specifications System spec. Continuous ELEMENT Request for quotation Type 2300 Type 8802-YG Type 8802-YG Technical data & ordering info. p. 1-7 Ordering info. & technical data p p p. 1/16

2 Technical data Type 2300, continued Kv values water/pressure size Kv value water Minimum pilot pressure +180º (m 3 /h) [bar] SF [bar] SF [bar] Flow rate: Kv value water [m 3 /h]: Measured at +20 C, 1 bar pressure at valve inlet and free outlet. ressure valves [bar]: Overpressure to the atmospheric pressure Flow characteristic Kv /Kvs [%] Stroke [%] Flow rate standard control valve Remarks on the flow characteristic Modified equi-percentile flow characteristic, engineered for a quick response during peak flow demand (an advantage for many processes like heating/cooling with heat exchangers) and fine control at lower flow. Kvs values [m 3 /h] ort size Stroke [%] and orifice / p. 2/16

3 Ordering chart Type 2300, flow direction below the seat (for gases and liquids) G threaded port size Ø ort thread TFE/St. st. St. st./st. st. 2/2-way valve, G 1/ G 3/ G G 1 1/ G 1 1/ G G 1/ G 3/ G G 1 1/ G 1 1/ G NT threaded port size Ø ort thread TFE/St. st. St. st./st. st. 2/2-way valve, NT 1/ NT 3/ NT 1/ NT 1 1/ NT 1 1/ NT NT 1/ NT 3/ NT 1/ NT 1 1/ NT 1 1/ NT RC threaded port size Ø ort thread pressure up to +180 C [bar] TFE/St. st. St. st./st. st. 2/2-way valve, RC 1/ RC 3/ RC 1/ RC 1 1/ RC 1 1/ RC RC 1/ RC 3/ RC 1/ RC 1 1/ RC 1 1/ RC p. 3/16

4 Ordering chart Type 2300, flow direction below the seat (for gases and liquids), continued Weld end acc. to EN ISO 112 size Ø ort tube-ø TFE/St. st. St. st./st. st. 2/2-way valve, x x x x x x x x x x x x Weld end acc. to DIN S2 size Ø ort tube-ø TFE/St. st. 2/2-way valve, x x x x x x x x x x x x p. 4/16

5 Ordering chart Type 2300, flow direction below the seat (for gases and liquids), continued Weld end acc. to SME E size Ø ort tube-ø TFE/St. st. 2/2-way valve, x x x x x x x x x x Weld end acc. to SMS 3008 size Ø ort tube-ø TFE/St. st. 2/2-way valve, x x x x x x x x x x Weld end acc. to S 4825 size Ø ort tube-ø TFE/St. st. 2/2-way valve, x x x x x x x x x x p. 5/16

6 Ordering chart Type 2300, flow direction below the seat (for gases and liquids), continued Clamp acc. to ISO 2852 size Ø ort clamp external Ø TFE/St. st. 2/2-way valve, Clamp acc. to SME E size Ø ort clamp external Ø TFE/St. st. 2/2-way valve, p. 6/16

7 Materials Type ilot air ports ush-in connector (standard) 2 S 3 Cover Stainless steel (316Ti) 4 iston seal FKM 5 Spring Stainless steel ipe Stainless steel (316) ( (316L) on request) 7 V-seals TFE 8 Spindle Stainless steel (316) ( (316L) on request) 9 Wiper EEK 10 lug Stainless steel lug seal Stainless steel (+TFE disc for soft seat sealing) 12 Valve body Stainless steel 316L p. 7/16

8 Ordering information for valve system Continuous ELEMENT Type 8802-YG valve system Continuous ELEMENT Type 8802-YG consists of an angle-seat control valve Type 2300 and a digital electropneumatic ositioner Type 8692, a digital electropneumatic rocess ler Type 8693 or a digital electropneumatic ositioner asic Type 8694 (for valve actuator sizes ø 70/90 mm) or a digital electropneumatic ositioner Type 8696 (for valve actuator size ø 50 mm) (see separate datasheets). For the configuration of further valve systems pleasee use the "Request for quotation" on p. 16 You order two components and receive a complete assembled and certified valve. Ordering the valve system Continuous ELEMENT Type 8802-YG with valve actuator sizes ø 70/90 mm ngle seat valve Type 2300 with actuator sizes ø 70/ ø 90 mm unit Type 8692 Type 8693 Type 8694 ngle seat valve with desired control unit Valve system Continuous ELEMENT Type 8802-YG-I Valve system Continuous ELEMENT Type 8802-YG-J Valve system Continuous ELEMENT Type 8802-YG-L Click on the orange box "More info." below... you will come to our website for the resp. product where you can download the datasheet. ositioner Top Type 8692 rocess ler Top Type 8693 ositioner Top asic Type 8694 The new generation of integrated positioners/process controllers for combination with actuators from the process valve series Type 23xx/2103 is specially designed for the requirements of hygienic process environments. The easy handling and the selection of additional software s are done either on a big graphic display with backlight and keypad or via a C interface. contact-free analog position sensor registers the valve position without deterioration. Single-acting or double-acting actuators are controlled via the integral positioner system. With Type 8693, the process controller is superimposed on the position control loop. rofibus DV1 and DeviceNet communication interfaces are available as options. Main customer benefits: Compact design of the valve system with integrated positioner/process controller meets the demands for plant washdown environments through the selection of materials, external seals and integrated control air supply to the actuator Extremely simple commissioning and operation thanks to the backlighting of the graphics display and proven multilingual software structure utomatic parameterisation of the positioner and process controller using the TUNE s Field bus communication via rofibus DV1 or DeviceNet ir intake filter enhances the process valve system availability Simple and reliable actuator adaption Explosion-proof models for zone 2/22 The new generation of integrated positioners for combination with actuators from the process valve series Type 23xx/2103 is specially designed for the requirements of hygienic process environments. The operation and selection of the software s close tight, inversion of the operating direction of the setpoint signal, characteristic curves selection and switching manual/automatic operation are effected via push-buttons and DI switches or via the C interface. The position setpoint is set using the standard signal 4-20 m. In addition, the enable can be controlled via the binary input and an optional position feedback can be integrated. The positioner, Type 8694, registers the valve position without deterioration through a contact-free analogue position sensor. Single-acting or double-acting actuators are controlled via the integral positioner system. n S-Interface communication interface is available as an option. Main customer benefits: Compact design of the valve system with integrated positioner meets the demands for plant washdown environments through the selection of materials, external seals and integrated control air supply to the actuator utomatic parameterisation of the process controller using the rocess TUNE Field bus communication via optional S-Interface ir intake filter enhances the process valve system availability Simple and reliable actuator adaption allowing additional actuators of the process valve series, Type 20xx or actuators from other manufacturers to be used Explosion-proof models for zone 2/22 p. 8/16

9 Ordering information for valve system Continuous ELEMENT Type 8802-YG, continued valve system Continuous ELEMENT Type 8802-YG consists of an angle-seat control valve Type 2300 and a digital electropneumatic ositioner Type 8692, a digital electropneumatic rocess ler Type 8693 or a digital electropneumatic ositioner asic Type 8694 (for valve actuator sizes ø 70/90 mm) or a digital electropneumatic ositioner Type 8696 (for valve actuator size ø 50 mm) (see separate datasheets). For the configuration of further valve systems pleasee use the "Request for quotation" on p. 16 You order two components and receive a complete assembled and certified valve. Ordering the valve system Continuous ELEMENT Type 8802-YG with valve actuator size ø 50 mm ngle seat valve Type 2300 with actuator sizes ø 50 mm unit Type 8696 ngle seat valve with desired control unit Valve system Continuous ELEMENT Type 8802-YG-N Click on the orange box "More info." below... you will come to our website for the resp. product where you can download the datasheet. Top asic Type 8696 The new generation of integrated positioners for combination with small actuators from the process valve series Type 23xx/2103 is specially designed for the requirements of hygienic process environments. The operation and selection of the software s close tight, inversion of the operating direction of the setpoint signal, characteristic curves selection and switching manual/automatic operation are effected via push-buttons and DI switches or via the C interface. The position setpoint is set using the standard signal 4-20 m. In addition, the enable can be controlled via the binary input and an optional position feedback can be integrated. The positioner, Type 8696,, registers the valve end position without deterioration through a contact-free analogue position sensor. Single-acting actuators are controlled via the integral positioner system. Main customer benefits: Compact design of the valve system with integrated positioner meets the demands for plant washdown environments through the selection of materials, external seals and integrated control air supply to the actuator utomatic parameterisation of the positioner using the TUNE Simple and reliable actuator adaption Explosion-proof models for zone 2/22 p. 9/16

10 Dimensions for valve system Continuous ELEMENT Type 8802-YG Dimensions valve system Continuous ELEMENT Type 8802-YG-I with positioner Top Type 8692 or 8802-YG-J with process controller Top Type 8693 Threaded body ll bodies G NT Rc size H M C L SW D E D E D E G 3/4 16 NT 3/4 14 RC 3/ G 1 18 NT RC G 1 1/4 20 NT 1 1/ RC 1 1/ G 1 1/2 22 NT 1 1/ RC 1 1/ G 2 24 NT RC Clamp body ll clamp bodies ISO 2852 DIN S 4825 SME E size H T CT LT ød1t ød2t ST ød1t ød2t ST ød1t ød2t ST ød1t ød2t ST p. 10/16

11 Dimensions for valve system Continuous ELEMENT Type 8802-YG, continued Dimensions valve system Continuous ELEMENT Type 8802-YG-I with positioner Top Type 8692 or 8802-YG-J with process controller Top Type 8693 Welded body ISO 4200, DIN S2, SME E ll bodies acc. to ISO 4200, DIN S2, SME E, S 4825 ISO 4200 DIN S2 SME E S 4825 size H CS LS S WS ø DS WS ø DS WS ø DS WS ø DS SMS 3008 size H CS LS S CS LS WS ø DS p. 11/16

12 Dimensions for valve system Continuous ELEMENT Type 8802-YG, continued Dimensions valve system Continuous ELEMENT Type 8802-YG-L with positioner Top asic Type 8694 Threaded body ll threaded bodies G NT Rc size H M C L SW D E D E D E G 3/4 16 NT 3/4 14 RC 3/ G 1 18 NT RC G 1 1/4 20 NT 1 1/ RC 1 1/ G 1 1/2 22 NT 1 1/ RC 1 1/ G 2 24 NT RC Clamp body ll clamp bodies ISO 2852 DIN S 4825 SME E size H T CT LT ø D1T ø D2T ST ø D1T ø D2T ST ø D1T ø D2T ST ø ø ST D1T D2T p. 12/16

13 Dimensions for valve system Continuous ELEMENT Type 8802-YG, continued Dimensions valve system Continuous ELEMENT Type 8802-YG-L with positioner Top asic Type 8694 Welded body ISO 4200, DIN S2, SME E ll welded bodies acc. to ISO 4200, DIN S2, SME E, S 4825 ISO 4200 DIN S2 SME E S 4825 size H CS LS S WS ø DS WS ø DS WS ø DS WS ø DS SMS 3008 size H S CS LS WS ø DS p. 13/16

14 Dimensions for valve system Continuous ELEMENT Type 8802-YG, continued Dimensions valve system Continuous ELEMENT Type 8802-YG with control head Type 8696 Threaded body ll threaded bodies ort G NT RC size H M CM SW LM D E D E D E G 1/2 14 NT 1/ RC 1/ G 3/4 16 NT 3/4 14 RC 3/ G 3/4 16 NT 3/4 14 RC 3/ G 1 18 NT RC G 1 18 NT RC G 1 1/4 20 NT 1 1/ RC 1 1/ Clamp body ll clamp bodies ISO 2852 DIN S 4825 SME E size H T CT LT ØD1T ØD2T ST ØD1T ØD2T ST ØD1T ØD2T ST ØD1T ØD2T ST p. 14/16

15 Dimensions for valve system Continuous ELEMENT Type 8802-YG, continued Dimensions valve system Continuous ELEMENT Type 8802-YG with control head Type 8696 Welded body ll welded bodies EN ISO 1127/ISO 4200 DIN S2 size H S CS LS ø DS WS S CS LS ø DS WS ll welded bodies SMS 3008 SME E size H S CS LS ø DS WS S CS LS ø DS WS ll welded bodies S 4825 size H S CS LS ø DS WS p. 15/16

16 Valve system Continuous ELEMENT Type 8802-YG - Request for quotation lease fill out and send to your nearest ürkert facility* with your inquiry or order Company Customer no. Contact person Department Note You can fill out the fields directly in the DF file before printing out the form. ddress ostcode/town Tel./Fax = mandatory fields to fill out Quantity Required delivery date data ipe line ipe material DN rocess medium Type of medium Liquid Steam Gas min standard max unit Flow rate (Q, QN, W) 1) Temperature at valve inlet T1 bsolute pressure at valve inlet 1 bsolute pressure at valve outlet 2 Steam pressure v Kinematic viscosity (ν) mm 2 /s or cst Dynamic viscosity (η) ma.s or c Standard density Kg/m 3 Max. sound level accepted d () 1) standard unit: Liquid Q = m 3 /h; Steam W = kg/h; Gas QN = Nm 3 /h Valve features Type of media Liquid Steam Gas lug seal material Nominal pressure Type of Standard lease specify item no. if known: N DN TFE/Stainless steel N Threaded Welded Clamp ISO DIN Other 2) 2) Stainless steel/stainless steel 2) : normally closed by spring action; : normally open by spring action unit features For actuator sizes 70/90 mm For actuator size 50 mm ositioner Top Type 8692 neumatic Single-acting Communication rofibus Electrical Cable gland rocess ler Top- Type 8693 Double-acting DeviceNet Multipol ositioner Top asic Type 8694 neumatic Single-acting ilot air ports ush-in connector external ø 6 mm or 1/4 Thread G 1/8 ositioner Top asic Type 8696 neumatic Single-acting Feedback Feedback Feedback 4-20 m 4-20 m + 2 binary outputs 4-20 m 4-20 m Initiator Initiator lease specify item no. if known: lease specify item no. if known: lease specify item no. if known: ilot air ports ush-in connector external ø 6 mm or 1/4 Thread G 1/8 Comments * To find your nearest ürkert facility, click on the orange box In case of special application conditions, please consult for advice. Subject to alteration. Christian ürkert GmbH & Co. KG 0909/6_EU-en_ p. 16/16