INLINE fitting with paddle-wheel for flow measurement

Size: px
Start display at page:

Download "INLINE fitting with paddle-wheel for flow measurement"

Transcription

1 INLINE fitting with paddlewheel for flow measurement 06 to 65 Closed pipe system, i.e. sensor inside fitting Quarterturn technology Type can be combined with... Electronics available for Indication, Monitoring, Transmitting On/Off control, Batch control Type 8030 Type 8032 Type SE30 Ex Type 8035 Type 8036 Flow sensor On/Off flow sensor/switch Flow sensor TEX version Flow transmitter Flow transmitter The fitting has a builtin paddlewheel to measure the flowrate. When liquid flows through the pipe, the paddlewheel is set in rotation producing pulses which frequency is proportional to the flowrate. This leads to a very leakproof construction, called the INLINE Quarterturn technology. The paddlewheel rotation is detected contactless through the fitting wall. The sensor unit can be snappedon or removed without opening the pipe or interrupting the process. The Bürkert Quarterturn technology General data ipe diameter Measurement range Flow velocity ccuracy 1) Linearity 1) Repeatability Fitting port connection Metal lastic Materials Seal Body Screws addlewheel Shaft and bearing 06 up to 65 from 0.5 up to 1200 l/min 0.3 up to 10 m/s (see flow diagram) Individual works calibration (TeachIn, via a remote transmitter) or standard mean Kfactor see accuracy chart on next page. ±0.5% of F.S.* (at 10 m/s) ±0.4% of Reading* Internal or external thread, weld ends, Clamp or flange True union, spigot or external thread FKM or EM (depending on version, see ordering chart) Stainless steel (316L ), brass (CuZn39b2), VC,, VF Stainless steel (316L ) VF ( on request or stainless steel, see data sheet 8030HT) Ceramics (l2o3) Medium data Fluid temperature Fluid pressure (max.) Metal lastic Fluid Solid particles rate Viscosity 0 up to 50 C (32 to 122 F) for fitting in VC 0 up to 80 C (32 to 176 F) for fitting in 15 up to 100 C (5 to 212 F) for fitting in stainless steel, brass or VF see pressure / temperature chart N16 ( SI) (N40 (580.4 SI) on request) N10 (145.1 SI) clean, neutral or slightly aggressive, solidfree liquids max. 1%, size of particles 0.5 mm max. 300 cst. max. * F.S. = Full scale (10 m/s) 1) Under reference conditions i.e. measuring fluid = water, ambient and water temperature = 20 C, applying the minimum inlet and outlet pipe straights, matched inside pipe dimensions. p. 1/10

2 Environment mbient temperature (operating and storage) s and approvals ressure pproval / Certificate on request 15 up to 50 C (5 to 122 F) for fitting in VC 15 up to 80 C (5 to 176 F) for fitting in 15 up to 100 C (5 to 212 F) for fitting in stainless steel, brass or VF depending on associated electronics Complying with article 3 of 3 from 97/23/CE directive.* 3.1 Certificate; 2.2 Certificate; Rugosity Certificate; Calibration Certificate; F (with EM seal) stainless steel fitting only * For the 97/23/CE pressure directive, the device can only be used under following conditions (depend on max. pressure, pipe diameter and fluid). Type of fluid Fluid group 1, 1.3.a Fluid group 2, 1.3.a Fluid group 1, 1.3.b Fluid group 2, 1.3.b Conditions 25 only 32 or > 32 and N* 1000 N* ressure / temperature chart ressure [bar] Temperature [ C] : pplication range for complete device (fitting + sensor ) ccuracy diagram For Type 8030, SE30 Ex, 8035 For Type 8032 Installation Minimum straight upstream and downstream distances must be observed. ccording to the pipe s design, necessary distances can be bigger or use a flow conditioner to obtain the best accuracy. For more information, please refer to ISO ISO prescribes the straight inlet and outlet distances that must be complied with when installing fittings in pipe lines in order to achieve calm flow conditions. The most important layouts that could lead to turbulence in the flow are shown below, together with the associated prescribed minimum inlet and outlet distances. These ensure calm, problemfree measurement conditions at the measurement point. = orifice Fluid direction > Regulating valve 2 x 90 elbow joint Extension 2 x 90 elbow joint 3 dimensional 90 elbow joint or Tpiece Reduction p. 2/10

3 Installation The flow rate sensor, transmitter can be installed into either horizontal or vertical pipes. Selection fitting / pipe size Example: Correct Incorrect Specification of nominal flow: 10 m 3 /h Ideal flow velocity: m/s For these specifications, the diagram indicates a pipe size of 40 [or 50 for (*) mentioned fittings] Correct Incorrect Flow rate Incorrect Not recommended Correct Correct Incorrect ressure and temperature ratings must be respected according to the selected fitting material. The suitable pipe size is selected using the diagram Flow / Velocity /. Conception Holder Body addlewheel Shaft Seal Flow velocity * for following fittings: with external threads acc. to SMS 1145 with weldends acc. to, BS 4825 / SME BE or IN Series 2 Clamp acc. to, BS 4825 / SME BE or IN p. 3/10

4 INLINE fitting dimensions Internal thread connection G, NT or Rc in stainless steel (316L ) or brass (CuZn39b2) [inch] G 1/2 NT 1/2 Rc 1/ G 3/4 NT 3/4 Rc 3/ G 1 NT 1 Rc G 1 1/4 NT 1 1/4 Rc 1 1/ G 1 1/2 NT 1 1/2 Rc 1 1/ G 2 NT 2 Rc 2 L External thread connection G, NT or Rc in stainless steel (316L ), brass (CuZn39b2), VC (only 6 and 8) or VF (only 8) [inch] L G1/4 or G1/ /2** M 16 x G 3/ G G 1 1/ G 1 1/ M 55 x M 64 x ** G, NT, RC according to fitting version External thread connection SMS 1145, in stainless steel (316L ) Rd 40 x 1/ Rd 60 x 1/ Rd 70 x 1/6 p. 4/10

5 INLINE fitting dimensions Weld ends connection ISO 1127/ ISO 4200,, BS 4825 / SME BE or IN Series 2 in stainless steel (316L ) SME BE IN Series 2 SME BE IN Series 2 SME BE IN Series 2 BS 4825 / SME BE IN Series 2 BS 4825 / SME BE IN Series 2 BS 4825 / SME BE IN Series 2 BS 4825 / SME BE IN Series 2 BS 4825 / SME BE IN Series s p. 5/10

6 INLINE fitting dimensions Clamp connection ISO (for pipe ), *, BS 4825 / SME BE* or IN in stainless steel (316L ) * vailable with internal surface finish Ra = 0.8 mm ISO (for pipe ) SME BE IN ISO (for pipe ) SME BE IN ISO (for pipe ) SME BE IN ISO (for pipe ) BS 4825 / SME BE IN ISO (for pipe ) BS 4825 / SME BE IN ISO (for pipe ) BS 4825 / SME BE IN ISO (for pipe ) BS 4825 / SME BE IN ISO (for pipe ) BS 4825 / SME BE IN Flange connection (ISO N16), NSI B or 10 K in stainless steel (316L ) NSI NSI NSI NSI NSI NSI L Z x14.0 4x15.8 4x x14.0 4x15.8 4x x14.0 4x15.8 4x x18.0 4x15.8 4x x18.0 4x15.8 4x x18.0 4x19.0 4x p. 6/10

7 INLINE fitting dimensions True union connection IN 8063, STM 1785/76 or K in VC, IN in or in VF 08* * Only available in VC IN / ISO STM IN / ISO STM IN / ISO STM IN / ISO STM IN / ISO STM IN / ISO STM IN / ISO STM Spigot connection IN 8063 in VC IN in or in VF IN 8063 IN IN 8063 IN IN 8063 IN IN 8063 IN IN 8063 IN IN 8063 IN L H p. 7/10

8 Ordering chart for fitting ort connection Seal 06 ** 1/4 06** 1/2 08** 1/ Brass with VF paddlewheel Temperature max. 100 C, N16 Internal FKM G thread NT Rc (ISO7) External FKM G thread NT Rc (ISO7) Metric FKM 16 x 1.5 mm Stainless steel with VF paddlewheel Temperature max. 100 C, N16 Internal FKM G thread NT Rc (ISO7) External FKM G thread NT Rc (ISO7) EM SMS Weld ends FKM ) EM BS 4825/ SME BE ) IN S Clamp FKM ISO (for pipe ISO 1127/ISO4200) EM * BS 4825 / SME BE BS 4825 / SME BE* IN Flange FKM NSI B K Stainless steel with VF paddlewheel Temperature max. 100 C, N40 Internal thr. FKM G VC with VF paddlewheel Temperature max. 50 C, N10 True union FKM IN STM 1785/ K Spigot FKM IN Extern. thr. FKM G True union FKM without spigot EM with VF paddlewheel Temperature max. 80 C, N10 True union FKM IN Spigot FKM IN VF with VF paddlewheel Temperature max. 100 C, N10 True union FKM Spigot FKM Extern. thr. FKM * internal surface finish Ra = 0.8 mm ** external thread 1) EM seal 2) 20 only available in SME BE p. 8/10

9 Ordering chart accessories / spare parts (other versions on request) escription Oring set FKM for metal fitting, 06 to EM for metal fitting, 06 to FKM for plastic fitting, FKM for plastic fitting, FKM for plastic fitting, FKM for plastic fitting, FKM for plastic fitting, FKM for plastic fitting, FKM for plastic fitting, EM for plastic fitting, EM for plastic fitting, EM for plastic fitting, EM for plastic fitting, EM for plastic fitting, EM for plastic fitting, EM for plastic fitting, Sensor holder Stainless steel with paddlewheel (VF), gasket (FKM), screws and certificate for 06 and Stainless steel with paddlewheel (VF), gasket (FKM), screws and certificate for 15 up to Stainless steel with paddlewheel (VF), gasket (EM), screws and certificate for 15 up to Stainless steel with paddlewheel (VF), gasket (EM), screws and certificate, Ra int.= 0.8 mm for 15 up to Stainless steel with paddlewheel (), gasket (EM), screws and certificate for 06 and Stainless steel with paddlewheel (), gasket (EM), screws and certificate for 15 up to Brass with paddlewheel (VF), gasket (FKM), screws and certificate for 06 and Brass with paddlewheel (VF), gasket (FKM), screws and certificate for 15 up to Brass with paddlewheel (VF), gasket (EM), screws and certificate for 15 up to Brass with paddlewheel (), gasket (EM), screws and certificate for 15 up to VC with paddlewheel (VF), gasket (FKM), screws and certificate for 06 and VC with paddlewheel (VF), gasket (FKM), screws and certificate for 15 up to VC with paddlewheel (VF), gasket (EM), screws and certificate for 15 up to VC with paddlewheel (), gasket (EM), screws and certificate for 15 up to with paddlewheel (VF), gasket (FKM), screws and certificate for 15 up to with paddlewheel (VF), gasket (EM), screws and certificate for 15 up to with paddlewheel (), gasket (FKM), screws and certificate for 15 up to with paddlewheel (), gasket (EM), screws and certificate for 15 up to VF with paddlewheel (VF), gasket (FKM), screws and certificate for 06 and VF with paddlewheel (VF), gasket (FKM), screws and certificate for 15 up to VF with paddlewheel (VF), gasket (EM), screws and certificate for 15 up to pproval / Certificate 3.1 certificate certificate Rugosity certificate points calibration certificate F approval ** Oring set for metal fitting Oring set for plastic fitting ** depending on sensor holder version : flat gasket to use for holder with groove (old version) ORing to use for holder with lug (new version) p. 9/10

10 Interconnection possibilities with the Remote electronics Type 8025 Flow transmitter / batch controller Wall or panel mounted 4 20 m Relay ulse Type 8619 multicell controller Type 8032 Flow switch / transmitter Wallmounted transistor Compact electronics Type 8032 Flow switch / transmitter 420 m Relay Transistor input: 420 m (external setpoint) Type 8035 Flow transmitter / batch controller 420 m Relay ulse Type 8036 Flow transmitter 420 m ulse Sensor Type 8030 /SE30 Ex Flow sensor Frequency Type 8030 Flow sensor Frequency Type Metal or plastic Fitting To find your nearest Bürkert facility, click on the orange box In case of special application conditions, please consult for advice. Subject to alteration. Christian Bürkert GmbH & Co. KG 1010/8_EUen_ p. 10/10 neutrol International Limited Unit 173 rgyle Industrial Estate, rgyle Street, Nechells, Birmingham B7 5TE sales@pneutrol.com Tel: +44 (0)

INLINE fitting with paddle-wheel for flow measurement

INLINE fitting with paddle-wheel for flow measurement ININE fitting with paddlewheel for flow measurement Type can be combined with... N 06 to N 65 Closed pipe system, i.e. sensor inside fitting Quarterturn technology Electronics available for Indication,

More information

INLINE sensor-fitting with paddle wheel for flow measurement

INLINE sensor-fitting with paddle wheel for flow measurement INLINE sensorfitting with paddle wheel for flow measurement Type S030 can be combined for... 06 to 65 Closed pipe system, i.e. sensor included in fitting Quarterturn technology Transmitter available also

More information

INSERTION fitting for flow measurement or analysis

INSERTION fitting for flow measurement or analysis INSERTION fitting for flow measurement or analysis Type S020 can be combined with... Universal fitting for INSERTION sensors, transmitters, batch controllers in pure, aggressive or contamined liquids arge

More information

INSERTION flow sensor for continuous flow measurement

INSERTION flow sensor for continuous flow measurement INSERTION flow sensor for continuous flow measurement Economic integration in pipe systems without any additional piping 3-wire frequency pulse version to directly interface with PLC s (both PNP and NPN)

More information

Paddle-wheel flow controller for On/Off control

Paddle-wheel flow controller for On/Off control Paddle-wheel flow controller for On/Off control Type 8032 can be combined with... Indication, monitoring, transmitting and On/Off control in one device Programmable outputs (transistor or relay) Automatic-calibration:

More information

Paddle-wheel flow controller with optical principle for On/Off control

Paddle-wheel flow controller with optical principle for On/Off control Paddle-wheel flow controller with optical principle for On/Off control Type 8039 can be combined with... Indication, monitoring, transmitting and On/Off control in one device. Programmable s (transistor

More information

Paddle-wheel flow controller for On/Off control

Paddle-wheel flow controller for On/Off control Paddle-wheel flow controller for On/Off control Type 803 can be combined with... Indication, monitoring, transmitting and On/Off control in one device Programmable s (transistor or relay) Automatic-calibration:

More information

Inline Paddle Wheel Flow Switch

Inline Paddle Wheel Flow Switch Inline addle Wheel Flow Switch Economic integration in pipe systems without any additional piping Magnetic measuring principle Mechanical adjustment of setpoint Type can be combined with... Valve Alarm

More information

INSERTION flowmeter with paddle wheel, ELEMENT design

INSERTION flowmeter with paddle wheel, ELEMENT design INSERTION flowmeter with paddle wheel, design Up to PN, size of measurement pipes: DN to DN400 Configurable outputs: one or two transistor output(s) and single or dual 4... ma analog output(s) Removable

More information

Insertion magnetic inductive flowmeter

Insertion magnetic inductive flowmeter Insertion magnetic inductive flowmeter Sensor without moving parts Flowmeter with On/Off control Application related calibration by Teach-In function Clean in place (CIP) FDA-compliant materials Type 8041

More information

INLINE Flow sensor for hazardous area II 1 G/D - II 2 D - II 3 GD - I M1

INLINE Flow sensor for hazardous area II 1 G/D - II 2 D - II 3 GD - I M1 INLINE Flow sensor for hazardous area II G/D - II D - II GD - I M Type SE0 Ex can be combined with... Flow meter with NAMUR or NPN/PNP output signal Mounting, dismounting of electronics by a Quarter-Turn

More information

Positive displacement flowmeter for continuous flow measurement

Positive displacement flowmeter for continuous flow measurement 8070 Positive displacement flowmeter for continuous flow measurement High accuracy Medium with high viscosity Mounting and dismounting of the electronics by a quarter-turn Connection to Bürkert devices

More information

display on the wall or in a panel away from the inline sensor SE30 for easy meter reading.

display on the wall or in a panel away from the inline sensor SE30 for easy meter reading. Analogue Flow Rate Indicator, DN 15...; PN 1...16 Advantages / Benefits Reduced costs of ownership up to 6% Economic integration in pipe systems without any additional piping Shows flow rate with a large

More information

INSERTION Adapter/Fitting for analytical devices

INSERTION Adapter/Fitting for analytical devices INSERTION / for analytical devices Universal adapter/fitting for Type 8202 and 8222 measuring devices in pure, aggressive or polluted liquids Adaptation into standard piping systems or conversion of Bürkert

More information

Type 2712 (8630) Continuous TopControl System. General data Compatibility Materials of wetted parts Body Rotor Shaft Seal

Type 2712 (8630) Continuous TopControl System. General data Compatibility Materials of wetted parts Body Rotor Shaft Seal Positive displacement flow fitting for continuous and batch control High accuracy ± 0.5% 1/2 TO 4 (DN 15 to 100) INLINE Quarter Turn technology For highly viscous fluids Electronics for indication, monitoring,

More information

Type S030. Operating Instructions. Symbols used. INLINE fitting. Bedienungsanleitung Manuel d'utilisation

Type S030. Operating Instructions. Symbols used. INLINE fitting.   Bedienungsanleitung Manuel d'utilisation Type S030 INLINE fitting We reserve the right to make technical changes without notice. Technische Änderungen vorbehalten. Sous réserve de modifications techniques. Operating Instructions Bedienungsanleitung

More information

Inductive conductivity meter

Inductive conductivity meter Inductive conductivity meter Type 8228 can be combined with... Configurable outputs: up to 2 transistor and up to 2 analog 4... 20 ma outputs Removable backlighted display Simulation of process values

More information

Positive displacement flowmeter

Positive displacement flowmeter Positive displacement flowmeter Configurable outputs: one or two transistor output(s) and single or dual 4...20 ma current output(s) Removable backlit display of flow rate and/or 2 two totalized volumes

More information

3/2-way Miniature Rocker Solenoid Valve for pneumatic systems

3/2-way Miniature Rocker Solenoid Valve for pneumatic systems 66 /2-way Miniature Rocker Solenoid Valve for pneumatic systems Direct-acting High cycling rate Reduced power consumption CNOMO and Bürkert flange interface Type 66 can be combined with TEX Ex ia on request

More information

3/2-way Miniature Rocker Solenoid Valve for pneumatic systems

3/2-way Miniature Rocker Solenoid Valve for pneumatic systems 66 /2-way Miniature Rocker Solenoid Valve for pneumatic systems Direct-acting High cycling rate Reduced power consumption CNOMO and Bürkert flange interface Type 66 can be combined with TEX Ex ia on request

More information

INSERTION Adaptor for analysis

INSERTION Adaptor for analysis INSERTION Adaptor for analysis Type can be combined with... Universal adaptor for type 8202 and 8222 ELEMENT s in pure, aggressive or contaminated liquids Adaptation into standard piping systems or conversion

More information

2/2-way Quarter-Turn Ball Valve in stainless steel with pneumatic rotary actuator, DN 10-50

2/2-way Quarter-Turn Ball Valve in stainless steel with pneumatic rotary actuator, DN 10-50 2/2-way Quarter-Turn Ball Valve in stainless steel with pneumatic rotary actuator, 10-50 (2652) (2655) 2 or ball valve Pneumatic actuator Compact design Visual position indicator Types 2652/2655 can be

More information

3/2-way and 2 x 3/2-way Solenoid Valve for pneumatics

3/2-way and 2 x 3/2-way Solenoid Valve for pneumatics 654 3/-way and x 3/-way Solenoid Valve for pneumatics Compact design Single and manifold mounting Low power consumption Fast response times Space saving ( x 3/-way version) Type 654 can be combined with...

More information

2/2- and 3/2-way Ball Valve with pneumatic rotary actuator, plastic body, DN 10-50

2/2- and 3/2-way Ball Valve with pneumatic rotary actuator, plastic body, DN 10-50 /- and 3/-way Ball Valve with pneumatic rotary actuator, plastic body, DN -50 Radially expandable body Pneumatic actuator in compact model Optical position indicator Control valve acc. to NAMUR Type 5

More information

Type Pressure Transmitter with display. Pressure Transmitter. Technical data. DN15-50 Body material. Stainless steel 316L Actuator material

Type Pressure Transmitter with display. Pressure Transmitter. Technical data. DN15-50 Body material. Stainless steel 316L Actuator material 2/2-way Angle Seat Valve, manually operated, for media up to +180 C Position indication Adjustable flow rates Stainless steel 316L valve body Compact industrial design with long service life Excellent

More information

Positive displacement batch controller

Positive displacement batch controller 8075 Batch controller Positive displacement batch controller Type 8075 can be combined with... Compact version for DN15 to DN100 Dosing On site calibration by Teach-In Check of input/output signals Total

More information

Inductive conductivity meter

Inductive conductivity meter Inductive conductivity meter CIP version Type 8228 can be combined with... Standard version Perfect for concentrated liquids and wide conductivity range Pre-parameterized versions available for direct

More information

2/2 or 3/2 way direct acting rocker solenoid valve

2/2 or 3/2 way direct acting rocker solenoid valve 2/2 or 3/2 way direct acting rocker solenoid valve With isolating diaphragm Ultra low dead volume Type 6126 can be combined with... High back-pressure tightness Normally closed, normally open or universal

More information

2/2-way Angle Seat Valve, manually operated, for media up to +180 C

2/2-way Angle Seat Valve, manually operated, for media up to +180 C 2/2-way Angle Seat Valve, manually operated, for media up to +180 C Position indication Adjustable flow rates Stainless steel 316L valve body Compact industrial design with long service life /2702 can

More information

Magnetic Paddle Flow Sensor/Switch for Easy On/Off Control

Magnetic Paddle Flow Sensor/Switch for Easy On/Off Control Magnetic Paddle Flow Sensor/Switch for Easy On/Off Control INLINE Quarter-Turn ON/OFF Control System for Monitoring and Switching Mechanical adjustment of set point No contact to Fluid thanks to INLINE

More information

2/2-way Globe Valve for media up to +180 C, DN

2/2-way Globe Valve for media up to +180 C, DN 2/2-way Globe Valve for media up to +180 C, DN 10-100 Compact globe valve version Flange, threaded and welded ports as standard Stainless steel 316L valve body vailable with flow direction below and above

More information

2/2-way ball valve with electric rotary actuator, ball valve in stainless steel, DN 10-65

2/2-way ball valve with electric rotary actuator, ball valve in stainless steel, DN 10-65 2/2-way ball valve with electric rotary actuator, ball valve in, N 10-65 Suitable for aggressive media High flow rate value -piece Actuator with adjustable limit switches 2-piece Visual position indicator

More information

2/2- or 3/2-way- Rocker Solenoid Valve

2/2- or 3/2-way- Rocker Solenoid Valve 2/2- or /2-way- Rocker Solenoid Valve Direct acting Hermetic isolation of fluid 0 145 SI 1) DN 2 mm Type 6128 can be combined with... Sub-base, threaded port 22mm width per station Type 2507 Cable lug

More information

2/2 and 3/2-way Flipper Solenoid Valve, with hermetic isolation of fluid

2/2 and 3/2-way Flipper Solenoid Valve, with hermetic isolation of fluid 2/2 and 3/2-way Flipper Solenoid Valve, with hermetic isolation of fluid Low internal volume Low power consumption High back pressure tightness Optional impulse model Type 6124 can be combined with...

More information

3/2-way Small Solenoid Valve, G 1/8 - G 1/4 and sub-base

3/2-way Small Solenoid Valve, G 1/8 - G 1/4 and sub-base 3/2-way Small Solenoid Valve, G 1/8 - G 1/4 and sub-base Sub-base Direct-acting, normally closed and normally open Brass and stainless steel body Electrical cable plug Form A With or without manual override

More information

2/2 and 3/2-way ball valve with pneumatic rotary actuator

2/2 and 3/2-way ball valve with pneumatic rotary actuator 2/2 and 3/2-way ball valve with pneumatic rotary actuator Pneumatic rotary actuator Stainless steel ball valve External regulation of the pistons Full bore Type 8805 can be combined with Favourable flow

More information

Digital ph transmitter

Digital ph transmitter Digital ph transmitter Compact, remote versions for DN 15 to 200 Fully programmable ph transmitter functions for all kinds of ph-measurement tasks Large range of process connections with various fittings

More information

Flowmeter for Gases. Type Type can be combined with... Type 8802-YG Process control valve. Type 5281 Solenoid valve

Flowmeter for Gases. Type Type can be combined with... Type 8802-YG Process control valve. Type 5281 Solenoid valve Flowmeter for Gases Thermal mass flow measurement Pipe sizes up to 2" Integrated inlet and outlet pipes for flow conditioning -20mA signal output of process value Type can be combined with... Type 8802-YG

More information

2/2 or 3/2-way Miniature Rocker Solenoid Valve

2/2 or 3/2-way Miniature Rocker Solenoid Valve 2/2 or 3/2-way Miniature Rocker Solenoid Valve Type 0127 can be combined with... For maximum chemical resistance requirements Compact design with mm width and Cv ratings up to 0.08 Proven reliability since

More information

2/2 or 3/2 way ball valve with pneumatic rotary actuator

2/2 or 3/2 way ball valve with pneumatic rotary actuator 2/2 or 3/2 way ball valve with pneumatic rotary actuator Pneumatic rotary actuator Stainless steel ball valve External regulation of the pistons Full bore Type 8805 can be combined with Favourable flow

More information

2/2 way Angle-Seat Valve for medium up to C, DN15-50

2/2 way Angle-Seat Valve for medium up to C, DN15-50 Type 2000 can be combined with 2/2 way Angle-Seat Valve for medium up to + 180 C, DN15-50 High flow rates Very high cycle life Clamp body according to EN ISO 2852, BS 4825 or ASME BPE For process valves

More information

Digital ph transmitter

Digital ph transmitter Digital ph transmitter Compact, remote versions for DN 15 to 200 Fully programmable ph transmitter functions for all kinds of ph-measurement tasks Large range of process connections with various fittings

More information

Simple float switch TCL001/8181

Simple float switch TCL001/8181 Simple float switch Switch for neutral and aggressive liquids NO/NC, alternating Reed contact Vertical or horizontal mounting Molded lying leads (Type 8181) or cable (Type TCL001) Float switch with hermetically

More information

2/2-way ball valve with electric rotary actuator, ball valve in plastic, DN 10-50

2/2-way ball valve with electric rotary actuator, ball valve in plastic, DN 10-50 2/2-way ball valve with electric rotary actuator, ball valve in plastic, DN 10-50 Suitable for aggressive media High flow rate value Actuator with adjustable limit switches Visual position indicator Safe

More information

2/2-way Angle-Seat Control Valve with stainless steel design for media up to +180ºC, DN 13-50

2/2-way Angle-Seat Control Valve with stainless steel design for media up to +180ºC, DN 13-50 2/2-way ngle-seat Valve with stainless steel design for media up to +180ºC, DN 13-50 Excellent control characteristic and high fl ow rates High cycle life Clean design for optimal use in hygienic environment

More information

2/2-way Compact Solenoid Valve, G 1/4 - G 1/2

2/2-way Compact Solenoid Valve, G 1/4 - G 1/2 2/2-way Compact Solenoid Valve, G 1/4 - G 1/2 Stainless steel body Type 6027 Compact can be combined with Direct-acting, normally closed Brass and stainless steel body Electrical connection cable plug

More information

2/2-way-Globe Valve with stainless steel design for media up to +180ºC, DN 13-50

2/2-way-Globe Valve with stainless steel design for media up to +180ºC, DN 13-50 2/2-way-Globe Valve with stainless steel design for media up to +180ºC, DN 13-50 High cycle life Flow optimised body in stainless steel 316L Deliverable with fl ow direction below or above seat Clean design

More information

2/2 or 3/2 way direct acting rocker solenoid valve

2/2 or 3/2 way direct acting rocker solenoid valve 2/2 or 3/2 way direct acting rocker solenoid valve With isolating diaphragm Ultra low dead volume Type 6126 can be combined with... High back-pressure tightness Normally closed, normally open or universal

More information

2/2-way Solenoid Valve with servo diaphragm

2/2-way Solenoid Valve with servo diaphragm 2/2-way Solenoid Valve with servo diaphragm Type 5282 can be combined with... Pivoted armature pilot drive with manual override Magnetic drive completely isolated from fluid by diaphragm Circuit function

More information

2/2-way Solenoid Valve with servo diaphragm, G 3/8 - G 2

2/2-way Solenoid Valve with servo diaphragm, G 3/8 - G 2 2/2-way Solenoid Valve with servo diaphragm, G 3/8 - G 2 Type 6281 can be combined with... User friendly - one solenoid for all orifices Waterhammer free and low noise NC or NO Manual override optional

More information

2/2-way ball valve with electric rotary actuator, ball valve in stainless steel, DN 10-65

2/2-way ball valve with electric rotary actuator, ball valve in stainless steel, DN 10-65 2/2-way ball valve with electric rotary actuator, ball valve in stainless steel, 10-65 Suitable for aggressive media High flow rate value -piece Actuator with adjustable limit switches 2-piece Visual position

More information

Direct-acting 3/2 way plunger valve

Direct-acting 3/2 way plunger valve Direct-acting 3/2 way plunger valve Direct-acting, compact valve with diameter of up to DN 2.5 Vibration-proof, bolted coil system Banjo threaded connection for direct mounting on pneumatic valves Type

More information

2/2-way Globe Valve for media up to +180 C, DN

2/2-way Globe Valve for media up to +180 C, DN 2/2-way Globe Valve for media up to +180 C, DN 10-100 Compact globe valve version Flange, threaded and welded ports as standard Stainless steel 316L valve body Available with flow direction below and above

More information

Cable Plug acc. to DIN EN , Form A

Cable Plug acc. to DIN EN , Form A Cable Plug acc. to DIN EN 175301-803, Form A Complete program Contact form 18 mm Also available with LED indicator Optional 4-pin version for pressure switch or impulse valves respectively Versions with

More information

2/2-way Angle Seat Valve, manually operated, for media up to +180 C

2/2-way Angle Seat Valve, manually operated, for media up to +180 C 2/2-way Angle Seat Valve, manually operated, for media up to +180 C Position indication Adjustable flow rates Stainless steel valve body Compact industrial design with long service life /2702 can be combined

More information

Pneumatically operated zero dead volume T-Valve CLASSIC

Pneumatically operated zero dead volume T-Valve CLASSIC Pneumatically operated zero dead volume T-Valve CLASSIC Zero dead volume body - no welds Hermetical separation of fluids from the operating mechanism by diaphragm Universal and robust actuators with modular

More information

mass flowmeter for compressed air

mass flowmeter for compressed air mass flowmeter for compressed air VARIOMASS LC pressure and temperature compensated flowmeter easy and cost effective installation of the senor no pressure loss caused by the sensor no moving parts, i.e.

More information

3/2-way Solenoid Valve, direct-acting, NC or NO

3/2-way Solenoid Valve, direct-acting, NC or NO 3/2-way Solenoid Valve, direct-acting, NC or NO Electrical connection cable plug, Form A With or without manual override as standard Threaded port and sub-base s Impulse optional Type 6014 can be combined

More information

Type SE35. Quickstart. English. Flowmeter Flow Transmitter

Type SE35. Quickstart. English. Flowmeter Flow Transmitter Flowmeter Flow Transmitter Quickstart 1. ABOUT THE QUICKSTART...3 2. INTENDED USE...4 3. BASIC SAFETY INFORMATION...4 4. GENERAL INFORMATION...6 5. DESCRIPTION OF THE NAME PLATE...6 6. TECHNICAL DATA...7

More information

2/2 and 3/2-way Flipper Solenoid Valve, with hermetic isolation of fluid

2/2 and 3/2-way Flipper Solenoid Valve, with hermetic isolation of fluid 2/2 and 3/2-way Flipper Solenoid Valve, with hermetic isolation of fluid Low internal volume Low power consumption High back pressure tightness Optional impulse model Type 612 can be combined with... DN

More information

82170/ /2-way diaphgram valves

82170/ /2-way diaphgram valves > > ort size: DN 8... 50, G1/4... 2 (ISO G/NT) > > For high contaminated fluids > > Solenoid hermetically sealed from fluid > > Compact valve for industrial applications > > Small dimension > > Vacuum

More information

2/2-way Diaphragm Valve with stainless steel design, weld end or clamp connection, DN 8-25

2/2-way Diaphragm Valve with stainless steel design, weld end or clamp connection, DN 8-25 2/2-way Diaphragm Valve with stainless steel design, weld end or clamp connection, DN 8-25 Type 2103 can be combined with Hermetical separation of fl uids from the operating mechanism by diaphragm Zero

More information

3/2-way Solenoid Valve for pneumatics

3/2-way Solenoid Valve for pneumatics 656 3/-way Solenoid Valve for pneumatics Compact design Single and manifold mounting Low power consumption Rocker pilot in DC Type 656 can be combined with... Fast response times Type 506 Type 510/511

More information

3/2-way Rocker Solenoid Valve for pneumatic systems

3/2-way Rocker Solenoid Valve for pneumatic systems 3/-way Rocker Solenoid Valve for pneumatic systems EEx ia versions Direct-acting High cycling rate Reduced power consumption Type 6104 can be combined with... Sub-base connection Approvals: Type 654 Servo-assisted

More information

2/2-way Angle-Seat Valve for medium up to +180 C, threaded port connection, DN 15-65

2/2-way Angle-Seat Valve for medium up to +180 C, threaded port connection, DN 15-65 2/2-way Angle-Seat Valve for medium up to +180 C, threaded port connection, DN 15-65 Type 2000 can be combined with High flow rate Long life cycle NC and NO universal s with modular universal accessory

More information

Belt Scales Milltronics belt scales

Belt Scales Milltronics belt scales Overview pplication provides continuous, in-line weighing at minimal cost. The stainless steel load cells ensure long-term, consistent, reliable measurement. The modular construction and easy assembly

More information

3/2-, 5/2- and 5/3-way Solenoid Valves for process pneumatics

3/2-, 5/2- and 5/3-way Solenoid Valves for process pneumatics /2-, 5/2-5/-way Solenoid Valves for process pneumatics Type 658 stard High flow-rate capacity Reduced power consumption Single or manifold mounting stard Type 658/659 can be combined with... Stard-, EEx

More information

Type Operating Instructions. Bedienungsanleitung Manuel d utilisation

Type Operating Instructions. Bedienungsanleitung Manuel d utilisation Flowmeter with paddle-wheel Durchfluss-Messgerät mit Flügelrad Débitmètre à ailette Operating Instructions Bedienungsanleitung Manuel d utilisation We reserve the right to make technical changes without

More information

Types 8025 / Operating Instructions. Bedienungsanleitung Manuel d utilisation. Flowmeter Durchflussmessgerät Débitmètre

Types 8025 / Operating Instructions. Bedienungsanleitung Manuel d utilisation. Flowmeter Durchflussmessgerät Débitmètre Types 805 / 8035 Flowmeter Durchflussmessgerät Débitmètre Operating Instructions Bedienungsanleitung Manuel d utilisation We reserve the right to make technical changes without notice. Technische Änderungen

More information

Electromagnetic amplifier type ModMAG M10 for all detectors

Electromagnetic amplifier type ModMAG M10 for all detectors Badger Meter Europa GmbH Nürtinger Str. 76 72639 Neuffen (Germany) Tel. +49-7025-9208-0 Fax +49-7025-9208-15 www.badgermeter.de badger@badgermeter.de Electromagnetic amplifier type ModMG M10 for all detectors

More information

2/2 or 3/2-way Solenoid Valve, with pivoted armature and isolating diaphragm

2/2 or 3/2-way Solenoid Valve, with pivoted armature and isolating diaphragm / or 3/-way Solenoid Valve, with pivoted armature and isolating diaphragm Type 0330 can be combined with Lockable manual override as standard For liquid, gaseous and aggressive media Long service life,

More information

Type Operating Instructions. Bedienungsanleitung Manuel d utilisation

Type Operating Instructions. Bedienungsanleitung Manuel d utilisation Flowmeter with paddle-wheel Durchfluss-Messgerät mit Flügelrad Débitmètre à ailette Operating Instructions Bedienungsanleitung Manuel d utilisation We reserve the right to make technical changes without

More information

Direct-acting 2/2- or 3/2-way pivoted armature valve

Direct-acting 2/2- or 3/2-way pivoted armature valve 0330 Direct-acting 2/2- or 3/2-way pivoted armature valve Direct-acting, media-separated valve with diameter of up to DN 5 Maintenance-free pivoted armature technology Vibration-proof, block screwed coil

More information

2/2- and 3/2-way solenoid valve for aggressive fluids

2/2- and 3/2-way solenoid valve for aggressive fluids 2/2- and 3/2-way solenoid valve for aggressive fluids Type 0121 can be combined with Direct-acting, media-separated valve with diameter of up to DN 8 Maintenance-free pivoted armature technology Vibration-proof,

More information

flow x3 flow monitoring

flow x3 flow monitoring flow x3 flow monitoring The FlowX3 System includes a complete range of paddle wheel flow sensors, instruments and sensor installation fittings. Also included are insertion type electromagnetic flow transmitters.

More information

Fluid Control System with Quarter-Turn Ball Valve for normal, aggressive and ultra-pure fluids. TOP Control System 265X

Fluid Control System with Quarter-Turn Ball Valve for normal, aggressive and ultra-pure fluids. TOP Control System 265X TOP Control System 65X /-Way; DN 0...80 mm; Plastic or Stainless Steel dvantages/benefits Decentralized ntelligence for ON/OFF control of processes Customized Fluid Control Systems for Easy LNK and Easy

More information

2/2 or 3/2-way Solenoid Valve, with pivoted armature and isolating diaphragm

2/2 or 3/2-way Solenoid Valve, with pivoted armature and isolating diaphragm 2/2 or 3/2-way Solenoid Valve, with pivoted armature and isolating diaphragm Lockable manual override as standard For liquid, gaseous and aggressive media Long service life, even in non-lube conditions

More information

2/2-way Diaphragm Valve with plastic body, pneumatically operated,

2/2-way Diaphragm Valve with plastic body, pneumatically operated, /-way Diaphragm Valve with plastic body, pneumatically operated, - pplications with aggressive media Flow-optimised body with zero dead volume Self-draining installation possible Removable radial true

More information

Solenoid valve. Technical data Orifice 1/4 4 Body materials Actuator material Seal material Media Viscosity. Control medium Port connections

Solenoid valve. Technical data Orifice 1/4 4 Body materials Actuator material Seal material Media Viscosity. Control medium Port connections /-way Diaphragm Valve with plastic body, pneumatically operated, 1/ 3 with true union 3 with fl ange pplications with aggressive media Flow optimised body with zero dead volume Self draining installation

More information

Direct-acting 2/2-way plunger valve

Direct-acting 2/2-way plunger valve Direct-acting 2/2-way plunger valve Type can be combined with Direct-acting and compact valve up to diameter of DN 6.0 Vibration-proof, bolted coil system Increased leak-tightness with welded plunger guiding

More information

Modular pneumatic valve unit

Modular pneumatic valve unit Modular pneumatic valve unit Compact design Modular configuration High flexibility Simple exchange of valves (with option P-shut-off - also possible during operation) Type 8640 can be combined with Type

More information

3/2-way and 2 x 3/2-way Rocker Solenoid Valve for pneumatics

3/2-way and 2 x 3/2-way Rocker Solenoid Valve for pneumatics 65 /-way and x /-way Rocker Solenoid Valve for pneumatics Type 65 can be combined with... Compact design Single and manifold mounting Low power consumption Rocker pilot in DC Fast response times Space

More information

86740/ /2-way piston valves

86740/ /2-way piston valves > > ort size: DN 8... 50, G1/4... 2 (ISO G/NT) > > Valve operates without differential pressure (Zero delta ) > > Suitable for vacuum > > Damped operation > > Valve piston with TFE guide-ring Technical

More information

Operating Instruction for Flowmonitor. Model: DF-WM

Operating Instruction for Flowmonitor. Model: DF-WM Operating Instruction for Flowmonitor Model: DF-WM 1. Contents 1. Contents... 2 2. Note... 3 3. Instrument Inspection... 3 4. Regulation Use... 4 5. Operating Principle... 5 6. Mechanical Connection...

More information

2/2-way Globe Control Valve, threaded port connection, DN 10-65

2/2-way Globe Control Valve, threaded port connection, DN 10-65 2/2-way Globe Control Valve, threaded port connection, DN 10-65 Type 2712 can be combined with... Classic design with interchangeable trims, 3 to 5 Kvs-value per connection port Excellent control characteristic

More information

/2-way piston valves

/2-way piston valves > > ort size: DN 15... 100, Flange connection, ressure rating N 40 > > djustable: Damped operation () > > Valve operates without differential pressure (Zero delta ) > > Valve piston with TFE guide-ring

More information

/2-way piston valves

/2-way piston valves > > ort size: DN 15... 100 Flange connection, ressure rating N 40 > > Valve operates without differential pressure (Zero delta ) > > Suitable for vacuum > > djustable: Damped operation () > > Valve piston

More information

Type Operating Instructions. Bedienungsanleitung Manuel utilisateur

Type Operating Instructions. Bedienungsanleitung Manuel utilisateur Water flow rate transmitter Wasser-Durchfluss-Transmitter Transmetteur de débit d eau Operating Instructions Bedienungsanleitung Manuel utilisateur We reserve the right to make technical changes without

More information

DFE10. solenoid control monoblock valve. Ordering codes. Description example : Diverter valve DFE10/3 A 18 ES - W VDC - SAE - <CVN>

DFE10. solenoid control monoblock valve. Ordering codes. Description example : Diverter valve DFE10/3 A 18 ES - W VDC - SAE - <CVN> DFE1 Ordering codes Description example : Diverter valve DFE1/3 18 ES - W 22-12VDC - SE - 1. 4. 5. 3. 5. 2. Valve is supplied painted as standard, with one coat of rimer black antirust paint II 5.

More information

SITRANS F flowmeters SITRANS F C

SITRANS F flowmeters SITRANS F C SITRNS F flowmeters Siemens G 2008 Overview is available as a standard version (DN 50 to DN 150 (2 to 6 )) and a hygienic, EHEDG certified version (DN 20 to DN 80 (¾ to 3 )). MC2 and MC2 hygienic are suitable

More information

Electromagnetic flowmeters Series FLOMAT Insertion electromagnetic flowmeter for conductive liquids

Electromagnetic flowmeters Series FLOMAT Insertion electromagnetic flowmeter for conductive liquids Electromagnetic flowmeters Series FLOMAT Insertion electromagnetic flowmeter for conductive liquids For use in large diameter pipes as an economical solution for flow measurement Flow rate measurement

More information

Type 2511/12. Type Type 2030 Cable plug. ASI cable plug. Dosing control. General technical data Orifice Type 6518

Type 2511/12. Type Type 2030 Cable plug. ASI cable plug. Dosing control. General technical data Orifice Type 6518 3/2-, 5/2- and 5/3-way Solenoid Valves for process pneumatics Type 658 standard standard High flow-rate capacity Reduced power consumption Single or manifold mounting Standard-, EEx m and EEx i versions

More information

Plug-in connections M3... M7, G 1/8... G 3/4

Plug-in connections M3... M7, G 1/8... G 3/4 Plug-in connections M3... M7, G 1/8... G 3/4 Nickel-plated brass, Stainless steel, Plastic, POM Straight threaded plug-in connections Basic fittings, short Basic fittings, long Schott-plug-in connections

More information

82610/ /2-way seat valves

82610/ /2-way seat valves > > ort size: DN 1,5... 5, 1/8... 3/8 (ISO G/NT) > > Suitable for vacuum > > High flow rate > > Functional compact design > > Solenoid interchangeable without tools (c) > > Valve operates without pressure

More information

Fluxi 2000/TZ Turbine Gas Meter

Fluxi 2000/TZ Turbine Gas Meter Fluxi 2000/TZ Turbine Gas Meter Turbine gas meters are flow meters. The flow of gas turns a turbine wheel, and thus, the rotating speed of the turbine is proportional to the linear speed of the gas. The

More information

2/2-way Diaphragm Valve, forged valve body, weld end and clamp connection, DN 8-100

2/2-way Diaphragm Valve, forged valve body, weld end and clamp connection, DN 8-100 2/2-way Diaphragm Valve, forged valve body, weld end and clamp, DN 8-100 Type 2031 with weld end Type 2031 can be combined with Type 2031 with clamp Hermetical separation of fluids from the operating mechanism

More information

Servo-operated 2/2-way solenoid valves Type EV220A

Servo-operated 2/2-way solenoid valves Type EV220A Data sheet Servo-operated 2/2-way solenoid valves Type is a compact servo-operated 2/2-way solenoid valve program, especially designed for use in machines and equipment with limited space. Features and

More information

3/2-way and 2 x 3/2-way Solenoid Valve for pneumatics

3/2-way and 2 x 3/2-way Solenoid Valve for pneumatics 654 3/-way and x 3/-way Solenoid Valve for pneumatics Compact design Single and manifold mounting Low power consumption Fast response times Space saving ( x 3/-way version) Type 654 can be combined with...

More information

Level Measurement Point level measurement - Vibrating switches

Level Measurement Point level measurement - Vibrating switches Overview Configuration Horizontal mounting (recommended mounting position, particularly for adhesive applications) Vertical mounting is a compact vibrating level switch for material detection in liquid

More information

PSF50 Paddle flow switch

PSF50 Paddle flow switch Paddle Flow Switch Paddle Flow Switch PSF50 Paddle flow switch Paddle flap flow / no flow switch Economically priced flow/no flow paddle operated flow switch. Simple and reliable design for liquids up

More information