Movotec Drives > Folding Hand Cranks (small and large)

Transcription

1 Movotec Drives > Folding Hand Cranks (small and large) Can be mounted right-at-hand, yet folds completely out of the way when not in use. The small crank has a 100 mm radius and is intended for lifting light to medium weight loads. The large crank has a 130 mm radius and is designed to lift larger loads with less effort. Small Crank Technical Data Materials: nylon handle with spring-loaded steel locking mechanism Operating temperature range: 0º F (-18º C) to 115º F (46º C) Product Note Large folding cranks are also available in a corrosion-resistant version for application in environments subjected to periodic wash-down. Please contact your SUSPA sales representative for additional information. Large Crank Basic Lift System Configuration Movotec Lift System activation is controlled by a DRIVE. The DRIVE is connected to the PUMP input shaft. The PUMP is then attached to the CYLINDERS by a series of CONNECTORS. CYLINDER extension and retraction is controlled through the PUMP, by means of clockwise and counter-clockwise rotation of the DRIVE. Please see the accompanying Technical Support Sheets for the proper selection of your remaining lift system components. Drives Small Crank Large Crank Motor Drive Pumps Small Pump Large Pump Dual Drive Connectors Tubing Ferrule Compression Nuts Cylinders CE Cylinder CS Cylinder CH Cylinder CB Cylinder Accessories A.T.U. Large Bracket Small Bracket Glide Mounting Glide Refill Kit

2 Folding Hand Cranks Dimension Chart: Standard Description Model Number A B C (mm) (mm) (mm) Small Crank FC Large Crank FC (PIN PLACEMENT) Ø 10 A B C CLEARANCE FOR FOLDING RADIUS Operating Instructions for the Folding Hand Crank The hand crank can be folded back and away from the user to nearly disappear under the top of the work surface. Top View Hand crank in operational position TABLE TOP SURFACE Front View TABLE FRONT EDGE max. 65mm Hand crank must be pulled to a stop in the direction of its axis TABLE TOP SURFACE TABLE FRONT EDGE Hand crank can then be folded under the worksurface top TABLE TOP SURFACE TABLE FRONT EDGE

3 Movotec Drives > Motor Drive Unit Providing push-button convenience, the new and improved Movotec motor drives are lighter, smaller, faster-operating, and carry the CE recognition mark. The new modular design is easy to install, and consists of a motor drive, transformer, and activation switch. Its safety features including a low-voltage isolation transformer and thermal and current limits protect against overheating and overload conditions. A Technical Data Material (motor and transformer): welded sheet metal enclosure (painted) Material (activation switch): plastic Input voltage: 110 VAC, 240 VAC Input current: 1.6 amps, 0.8 amps Transformer voltage (secondary): 22 VAC Transformer current (secondary): 8 amps Switch voltage: 5 VDC Switch current: 25 milliamps Duty cycle: 10% (intermittent) Operating temperature range: 0º F (-18º C) to 115º F (46º C) Can be used with either small or large pumps B C E D A. Pump/Motor Unit, B. Mounted Switch, C. 110 VAC Transformer, D. Hand Held Switch, E. 240 VAC Transformer Motor Unit Basic Lift System Configuration Movotec Lift System activation is controlled by a DRIVE. The DRIVE is connected to the PUMP input shaft. The PUMP is then attached to the CYLINDERS by a series of CONNECTORS. CYLINDER extension and retraction is controlled through the PUMP, by means of clockwise and counter-clockwise rotation of the DRIVE. Please see the accompanying Technical Support Sheets for the proper selection of your remaining lift system components. Drives Small Crank Large Crank Motor Drive Pumps Small Pump Large Pump Dual Drive Connectors Tubing Ferrule Compression Nuts Cylinders CE Cylinder CS Cylinder CH Cylinder CB Cylinder Accessories A.T.U. Large Bracket Small Bracket Glide Mounting Glide Refill Kit

4 Motor Drive Unit Description Model Number Notes Motor Drive Unit - TB (North America) M1S-TB for use w/ small pumps Motor Drive Unit - PB (North America) M1S-PB for use w/ large pumps Motor Drive Unit - TB (Europe) M2R-TB for use w/ small pumps Motor Drive Unit - PB (Europe) M2R-PB for use w/ large pumps Dimension Chart The C dimension depicted on this drawing varies depending on the size of the pump utilized in your lift system (longer adjustment ranges require longer pumps). Use the following chart to determine the actual dimension. Pump Model Number C (mm) TB1809, TB2809, PB3809, PB4809, PB5809, PB TB1812, TB2812, PB3812, PB4812, PB5812, PB TB1818, TB2818, PB3818, PB4818, PB5818, PB TB1824, TB2824, PB3824, PB4824, PB5824, PB PB3612, PB4612, PB5612, PB PB3615, PB4615, PB5615, PB PB3623, PB4623, PB5623, PB PB3631, PB4631, PB5631, PB To determine which pump is required for your lift system, please refer to the System Specification Guide on page 8. CABLE (2 METERS) CABLE (2 METERS) 7.5 (4X) 240 VAC 10.5 (4X) EUROPLUG (CEE 7/16) PLUG (NEMA 5-15P) 110 VAC Motor Unit TYP 90 TYP PB PROFILE TB PROFILE TB PROFILE PB PROFILE 57.5 TYP 70 Ø 4.3 HOLE (4X) CABLE (0.5 METERS) ACTIVATION SWITCH JACK TRANSFORMER JACK PB 54 PB R (10) TYP ENCLOSURE (BLACK) CABLE (BLACK) (1.8 METERS) LARGE PUMP PROFILE LARGE PUMP PROFILE Ø 6 HOLE ROCKER SWITCH (BLACK) Hand Held Switch LABEL Ø POSITION CIRCULAR DIN PLUG (BLACK) Motor/Pump SMALL PUMP PROFILE SMALL PUMP PROFILE C CABLE (BLACK-3M LONG) Ø 13.4 R 6 HOLE (2X) Ø 4.7 (2X) 25.4 TYP TYP 12 TYP 45 TYP 6 (2X) C OF PUMP Ø 6 HOLE (2X) Mounted Switch

5 Movotec Pumps > Small and Large Pump The small pump is the activation mechanism for 1-2 cylinder lift systems. The large pump is the activation mechanism for 3-6 cylinder lift systems. Technical Data Material: extruded aluminum housing/black matte anodized (durable long-lasting finish) Operating temperature range: 0º F (-18º C) to 115º F (46º C) Maximum drive speed: 110 rpm System operating parameters (maximum load ratings and actual adjustment ranges) are determined by specific pump and cylinder combinations. Please see the System Specification Guide (pg. 8) for detailed operating data and ordering information. Product Note Large pumps are also available in a corrosion-resistant version for application in environments subjected to periodic wash-down. Please contact your SUSPA sales representative for additional information. Small Pump Large Pump Basic Lift System Configuration Movotec Lift System activation is controlled by a DRIVE. The DRIVE is connected to the PUMP input shaft. The PUMP is then attached to the CYLINDERS by a series of CONNECTORS. CYLINDER extension and retraction is controlled through the PUMP, by means of clockwise and counter-clockwise rotation of the DRIVE. Please see the accompanying Technical Support Sheets for the proper selection of your remaining lift system components. Drives Small Crank Large Crank Motor Drive Pumps Small Pump Large Pump Dual Drive Connectors Tubing Ferrule Compression Nuts Cylinders CE Cylinder CS Cylinder CH Cylinder CB Cylinder Accessories A.T.U. Large Bracket Small Bracket Glide Mounting Glide Refill Kit

6 Small Pump (TB) and Large Pump (PB) Model Number and Dimension Chart The A and B dimensions depicted on this drawing vary depending on the size the pump utilized in your lift system (longer adjustment ranges require longer pumps). Use the following chart to determine the actual dimension. Description Model Number Dimensions 1 cylinder 2 cylinder 3 cylinder 4 cylinder 5 cylinder 6 cylinder A B pumps pumps pumps pumps pumps pumps (mm) (mm) Small Pump TB1809 TB Small Pump TB1812 TB Small Pump TB1818 TB Small Pump TB1824 TB Large Pump - - PB3809 PB4809 PB5809 PB Large Pump - - PB3812 PB4812 PB5812 PB Large Pump - - PB3818 PB4818 PB5818 PB Large Pump - - PB3824 PB4824 PB5824 PB Large Pump - - PB3612 PB4612 PB5612 PB Large Pump - - PB3615 PB4615 PB5615 PB Large Pump - - PB3623 PB4623 PB5623 PB Large Pump - - PB3631 PB4631 PB5631 PB To determine which pump is required for your lift system, please refer to the System Specification Guide on page Ø 5.8 HOLE (3X) Ø 5.8 HOLE (3X) A B A B Small Pump Large Pump Ø Ø 10

7 Movotec Pumps > Dual Drive The dual drive is the activation mechanism for 8 cylinder lift systems. This unit must be used in conjunction with heavy-duty CB cylinders only. The dual drive is a combination drive/pump unit, and is only offered in a motorized configuration. Technical Data Material: welded sheet metal enclosure (painted) 904 kg (2,000 U.S. lbs.) load capacity (maximum) Operating temperature range: 0º F (-18º C) to 115º F (46º C) Maximum drive speed: 60 rpm System operating parameters (maximum load ratings and actual adjustment ranges) are determined by specific pump and cylinder combinations. Please see the System Specification Guide (pg. 8) for detailed operating data and ordering information. Basic Lift System Configuration Movotec Lift System activation is controlled by a DRIVE. The DRIVE is connected to the PUMP input shaft. The PUMP is then attached to the CYLINDERS by a series of CONNECTORS. CYLINDER extension and retraction is controlled through the PUMP, by means of clockwise and counter-clockwise rotation of the DRIVE. Please see the accompanying Technical Support Sheets for the proper selection of your remaining lift system components. Drives Small Crank Large Crank Motor Drive Pumps Small Pump Large Pump Dual Drive Connectors Tubing Ferrule Compression Nuts Cylinders CE Cylinder CS Cylinder CH Cylinder CB Cylinder Accessories A.T.U. Large Bracket Small Bracket Glide Mounting Glide Refill Kit

8 Dual Drive Model Number and Dimension Chart The W dimension depicted on this drawing varies depending on the size of the pump utilized in your lift system (longer adjustment ranges require longer pumps). Use the following chart to determine the actual dimension. Model Number W (mm) PB PB To determine which pump is required for your lift system, please refer to the System Specification Guide on page W Ø 6.5 HOLES (4X)

9 Movotec Connectors > Compression Nuts / Ferrules / Tubing Compression Nuts / Ferrules Constructed of brass, these components ensure a time-tested seal. Two ferrules and compression nuts (each) are required for each cylinder in your application. Like the majority of our customers, let our production specialists assemble your system for you. Technical Data Material: brass Require a torque of 89 inch-pounds for a proper seal Tubing Flexible yet durable, Movotec tubing makes installation of your lift system simple and easy, whether you re retrofitting one table or manufacturing one thousand. Tubing can be custom-cut to desired lengths, please specify when ordering. Technical Data Material: nylon O.D.: 4 mm (0.157 in.) Minimum bend radius: 5 cm (2 in.) Maximum available length: 500 cm (16 ft.) Minimum available length: 40 cm (16 in.) Maximum ratio: 5:1 (the ratio of longest to shortest tube length cannot exceed 5:1) Basic Lift System Configuration Movotec Lift System activation is controlled by a DRIVE. The DRIVE is connected to the PUMP input shaft. The PUMP is then attached to the CYLINDERS by a series of CONNECTORS. CYLINDER extension and retraction is controlled through the PUMP, by means of clockwise and counter-clockwise rotation of the DRIVE. Please see the accompanying Technical Support Sheets for the proper selection of your remaining lift system components. Drives Small Crank Large Crank Motor Drive Pumps Small Pump Large Pump Dual Drive Connectors Tubing Ferrule Compression Nuts Cylinders CE Cylinder CS Cylinder CH Cylinder CB Cylinder Accessories A.T.U. Large Bracket Small Bracket Glide Mounting Glide Refill Kit kg = 1 U.S. lb. / 25.4 mm = 1 in. SUSPA Incorporated > Phone (616) > LIT M

10 Movotec Cylinders > CE, CS, and CH Cylinder Designed for O.E.M. applications, each cylinder utilizes a unique set of end-fitting configurations to assist in your design and manufacturing process. These cylinders must be used in conjunction with an external guide mechanism to prevent non-axial loading of the cylinder. The Movotec A.T.U. telescoping leg unit was engineered to support CE cylinders. CE cylinders have a 90º tubing port and grooved end-fittings for use with e-ring type fasteners. CS cylinders have an in-line tubing port and grooved end-fittings for use with e-ring type fasteners. CH cylinders have a 90º tubing port and end-fittings containing chamfered holes for use with pin- or bolt-type fasteners. Technical Data Materials: brass body with stainless steel rod Cylinders are single-acting, requiring an external force of kg (15-25 U.S. lbs.) for retraction Operating temperature range: 0º F (-18º C) to 115º F (46º C) Maximum cylinder load = 113 kg (250 U.S. lbs.) System operating parameters (maximum load ratings and actual adjustment ranges) are determined by specific pump and cylinder combinations. Please see the System Specification Guide (pg. 8) for detailed operating data and ordering information. CH CS CE Basic Lift System Configuration Movotec Lift System activation is controlled by a DRIVE. The DRIVE is connected to the PUMP input shaft. The PUMP is then attached to the CYLINDERS by a series of CONNECTORS. CYLINDER extension and retraction is controlled through the PUMP, by means of clockwise and counter-clockwise rotation of the DRIVE. Please see the accompanying Technical Support Sheets for the proper selection of your remaining lift system components. Drives Small Crank Large Crank Motor Drive Pumps Small Pump Large Pump Dual Drive Connectors Tubing Ferrule Compression Nuts Cylinders CE Cylinder CS Cylinder CH Cylinder CB Cylinder Accessories A.T.U. Large Bracket Small Bracket Glide Mounting Glide Refill Kit

11 CE, CS, and CH Cylinder Model Number and Dimension Chart The A and L dimensions depicted on this drawing vary depending on the size of the cylinder utilized in your lift system. Use the following chart to determine the actual dimension. Model Number A L CE Cylinder CS Cylinder CH Cylinder (mm) (mm) CE415 CS415 CH CE420 CS420 CH CE430 CS430 CH CE440 CS440 CH To determine which cylinder is required for your lift system, please refer to the System Specification Guide on page 8. Ø 11.9 Ø Ø 8.1 THROUGH HOLE Ø 11.9 Ø Ø 16 A Ø 16 A Ø 16 A Ø 10 Ø 10 Ø 10 L L L 11 Ø 8 Ø Ø 5 THROUGH HOLE 6 13 Ø 8 Ø CE Cylinder CH Cylinder CS Cylinder

12 Movotec Cylinders > CB Cylinder Designed for O.E.M. or retrofit applications, CB cylinders incorporate their own guide/support system and can be bolted onto virtually any surface, for use as a stand-alone telescoping leg unit. Technical Data Materials: extruded aluminum body (painted) with nickel-plated rod Cylinders are single-acting, requiring an external force of kg (20-30 U.S. lbs.) for retraction Operating temperature range: 0º F (-18º C) to 115º F (46º C) Offered in standard and heavy-duty configurations (for larger load ratings) Maximum standard cylinder load: 113 kg (250 U.S. lbs.) Maximum heavy-duty cylinder load: kg (330 U.S. lbs.) System operating parameters (maximum load ratings and actual adjustment ranges) are determined by specific pump and cylinder combinations. Please see the System Specification Guide (pg. 8) for detailed operating data and ordering information. Product Note CB cylinders are also available in a corrosion-resistant version for application in environments subjected to periodic wash-down. Please contact your SUSPA sales representative for additional information. Basic Lift System Configuration Movotec Lift System activation is controlled by a DRIVE. The DRIVE is connected to the PUMP input shaft. The PUMP is then attached to the CYLINDERS by a series of CONNECTORS. CYLINDER extension and retraction is controlled through the PUMP, by means of clockwise and counter-clockwise rotation of the DRIVE. Please see the accompanying Technical Support Sheets for the proper selection of your remaining lift system components. Drives Small Crank Large Crank Motor Drive Pumps Small Pump Large Pump Dual Drive Connectors Tubing Ferrule Compression Nuts Cylinders CE Cylinder CS Cylinder CH Cylinder CB Cylinder Accessories A.T.U. Large Bracket Small Bracket Glide Mounting Glide Refill Kit

13 CB Cylinder Model Number and Dimension Chart: Standard The A, B and L dimensions depicted on this drawing vary depending on the size of the cylinder utilized in your lift system. Use the following chart to determine the actual dimension. Model Number A B L (mm) (mm) (mm) CB CB CB CB CB615* CB631* *Heavy duty cylinders for larger loads. Please see the System Specification Guide (pg. 8) for detailed operating data M5x0.8 (7.0 DEEP) HOLE (4X) B A 35 L 12 M10x1.5 Ø 25

14 Movotec Accessories > Aluminum Telescoping Uprights (A.T.U.) With smooth telescoping movement and rigid structural integrity, our two-piece anodized aluminum extrusion was designed to support the application of CE cylinders. Engineered to be used as a free-standing leg unit or external guide mechanism, the A.T.U. supports the use of many types of brackets, hardware, or other structural components. For O.E.M. applications only. Technical Data Materials: extruded aluminum with clear matte anodized finish Adjustment range: 300 mm (11.8 in.) 600 mm (23.6 in.) fully compressed 900 mm (35.4 in.) fully extended Operating temperature range: 0º F (-18º C) to 115º F (46º C) Designed to be used with CE cylinders Basic Lift System Configuration Movotec Lift System activation is controlled by a DRIVE. The DRIVE is connected to the PUMP input shaft. The PUMP is then attached to the CYLINDERS by a series of CONNECTORS. CYLINDER extension and retraction is controlled through the PUMP, by means of clockwise and counter-clockwise rotation of the DRIVE. Please see the accompanying Technical Support Sheets for the proper selection of your remaining lift system components. Drives Small Crank Large Crank Motor Drive Pumps Small Pump Large Pump Dual Drive Connectors Tubing Ferrule Compression Nuts Cylinders CE Cylinder CS Cylinder CH Cylinder CB Cylinder Accessories A.T.U. Large Bracket Small Bracket Glide Mounting Glide Refill Kit

15 Aluminum Telescoping Uprights (A.T.U.) Description Movotec guide mechanism Model Number ATU-600/300-E BOSS ACCEPTS 5/16 " 18 THREAD FORMING SCREW FOR WORK SURFACE OR FOOT 42.5 BOSS ACCEPTS 1/4 " HEX HEAD SCREW OR BOLT FOR CROSS BEAM UPPER BEARING ASSEMBLY TO 300 ADJUSTMENT

16 Movotec Accessories > Brackets / Glides Large and Small Mounting Brackets Mounted to the face of the CB cylinder body, these brackets assist in the application of the cylinder. Two brackets are required for each cylinder. Glides The standard foot pad for CB cylinders. This glide is adjustable for uneven floor surfaces. Mounting Glides Also for supporting the CB cylinder, this glide may be used as a mountable version of our standard glide, or inverted and used as a mounting bracket when the cylinder is mounted rod up (upside down). Technical Data Mounting bracket material: aluminum Glide material: nylon base, T.P.E. pad, steel stem Mounting glide material: aluminum base, steel stem Operating temperature range: 0 F (-18 C) to 115 F (46 C) Glide Product Note Glides and mounting glides are also available in a corrosion-resistant version for application in environments subjected to periodic wash-down. Please contact your SUSPA sales representative for additional information. Mounting Glide Small Mounting Bracket on cylinder Large Mounting Bracket on cylinder Small Mounting Bracket Large Mounting Bracket Basic Lift System Configuration Movotec Lift System activation is controlled by a DRIVE. The DRIVE is connected to the PUMP input shaft. The PUMP is then attached to the CYLINDERS by a series of CONNECTORS. CYLINDER extension and retraction is controlled through the PUMP, by means of clockwise and counter-clockwise rotation of the DRIVE. Please see the accompanying Technical Support Sheets for the proper selection of your remaining lift system components. Drives Small Crank Large Crank Motor Drive Pumps Small Pump Large Pump Dual Drive Connectors Tubing Ferrule Compression Nuts Cylinders CE Cylinder CS Cylinder CH Cylinder CB Cylinder Accessories A.T.U. Large Bracket Small Bracket Glide Mounting Glide Refill Kit

17 Small Mounting Bracket Large Mounting Bracket Fasteners not included Ø 5.8 TYP 31.8 Ø 5.8 TYP M6 NUT M6x1.0 THREAD Glide Mounting Glide Ø 36 Ø 50.8 R Ø 26 M10x1.5 THREAD M10 NUT Ø 5.6 (3X) 120 TYP

18 Movotec Refill Kit Should your Movotec Lift System ever become damaged, our refill kit contains enough components to make most minor repairs. The kit comes complete with: 10 meters tubing 0.5 liter of fluid 12 compression nuts 12 ferrules A filler bottle M.S.D.S. sheets Detailed instructions Basic Lift System Configuration Movotec Lift System activation is controlled by a DRIVE. The DRIVE is connected to the PUMP input shaft. The PUMP is then attached to the CYLINDERS by a series of CONNECTORS. CYLINDER extension and retraction is controlled through the PUMP, by means of clockwise and counter-clockwise rotation of the DRIVE. Please see the accompanying Technical Support Sheets for the proper selection of your remaining lift system components. Drives Small Crank Large Crank Motor Drive Pumps Small Pump Large Pump Dual Drive Connectors Tubing Ferrule Compression Nuts Cylinders CE Cylinder CS Cylinder CH Cylinder CB Cylinder Accessories A.T.U. Large Bracket Small Bracket Glide Mounting Glide Refill Kit

19 VERSALIFT Introducing SUSPA s new electronically-controlled Linear Actuator Systems that are designed for streamlined, efficient integration into desks and table legs. The systems are a premier solution for office furniture applications, due to their compact size, lifting strength, speed, and quiet operation. The new VERSALIFT includes an integrated motor-driven actuator/cylinder assembly, a power transformer, and a surface-mounted activation switch. SUSPA representatives are available to assist customers in the proper application of the Linear Actuator Systems. Leg Actuator Load kg ( U.S. lbs.) maximum load per leg Speed 5-25 mm/s (.2-1 in/s) Stroke mm (6-17 in.) Compact design Original equipment manufacturer Planetary gearbox Fully synchronized even in unbalanced loading conditions Control Box 100/110/240 VAC 50 Hz input power capability Controls up to six legs simultaneously Mounts with four screws Switch Up/down buttons Mounts with two screws Motor Detail

20 VERSALIFT Spindle Model Legs Stroke Pitch Voltage Number (mm) (mm) A B Ø 5 HOLE (3X) 5 Ø 4 HOLE (3X) Ø 3 HOLE (3X) Ø 9 Ø 22 6 mm Spindle Pitch: DO NOT EXCEED 90.4 kg (200 U.S. lbs.)

21 Movotec Quick-Ship Lift Systems Convenient, easy-to-install bolt-on ergonomic lift systems adjust work-station height to each person or task. They can be installed quickly with just a few common tools on tables, benches, desks, platforms, conveyors, etc. Attach the pump, route the flexible tubing, and bolt on the cylinders. Whether motorized or crank driven, you can transform your current workbench, platform or other structure into a height-adjustable workstation. Movotec Quick-Ship Lift Systems are available in five different adjustable ranges, and are capable of lifting loads of up to 452 kg (1,000 U.S. lbs.). Level elevation is achieved even when the system is subjected to unbalanced loading conditions. Crank Driven Lift System Each Movotec Quick-Ship system is shipped within 3-5 working days, comes completely assembled, and includes: Motorized switch and power supply available, or pump unit driven by our unique fold-away hand crank Two 8 ft. sections of flexible tubing Two 10 ft. sections of flexible tubing Four lift cylinders Four glides Ten tubing clips (adhesive backed) and cable ties A tube shortening kit Motor Driven Lift System B C Before Movotec E A D A. 110 VAC Transformer, B. Mounted Switch, C. 240 VAC Transformer, D. Hand Held Switch, E. Tubing Clips and Cable Ties After Movotec

22 Quick-Ship Systems / Manual Specification Chart and Dimensions The A, B, L, X and Y dimensions depicted on the drawings vary depending on the size of the cylinder utilized in your lift system. Use the following chart to determine the actual dimension. See the back page for folding hand crank positions. Adjustment Lift Model Number Range Capacity A B L X Y (mm) (U.S. lbs.) (mm) (mm) (mm) (mm) (mm) MQS MQS MQS MQS MQS MQS MQS CB Cylinder with Glide (for manual and motorized applications) Pump with Small Crank M5x0.8 (7.0 DEEP) HOLE (4X) Ø 5.8 HOLE (3X) B A X Y L kg = 1 U.S. lb. / 25.4 mm = 1 in.

23 Quick-Ship Systems / Motorized Specification Chart and Dimensions The A, B, L, and C dimensions depicted on the drawings vary depending on the size of the cylinder utilized in your lift system. Use the following chart to determine the actual dimension. Adjustment Lift Model Number Range Capacity A B L C (mm) (U.S. lbs.) (mm) (mm) (mm) (mm) MQS-00001M MQS-00002M MQS-00003M MQS-00004M MQS-00005M MQS-00006M MQS-00007M * Approximately 15 mm of stroke is lost due to sensor safety margin (for motorized only). Motor Cable and Motor Cable Plug CABLE (BLACK-3M LONG) Ø 13.4 Motor Drive Unit PB PROFILE TB PROFILE Ø 4.7 (2X) 25.4 TYP 50.8 TB PROFILE PB PROFILE ACTIVATION SWITCH JACK TRANSFORMER JACK PB 54 PB LARGE PUMP PROFILE LARGE PUMP PROFILE Ø 6 HOLE CABLE (2 METERS) CABLE (2 METERS) 240 VAC EUROPLUG (CEE 7/16) PLUG (NEMA 5-15P) SMALL PUMP PROFILE SMALL PUMP PROFILE C 7.5 (4X) 10.5 (4X) 99.8 TYP 90 TYP VAC 69 TYP 12 TYP 45 TYP R 6 HOLE (2X) 6 (2X) C OF PUMP TYP 70 Ø 4.3 HOLE (4X) CABLE (0.5 METERS) Ø 6 HOLE (2X)

24 Folding Hand Crank Positions The hand crank can be folded back and away from the user to nearly disappear under the top of the work surface. Top View Hand crank in operational position TABLE TOP SURFACE Front View TABLE FRONT EDGE max. 65mm Hand crank must be pulled to a stop in the direction of its axis TABLE TOP SURFACE TABLE FRONT EDGE Hand crank can then be folded under the worksurface top TABLE TOP SURFACE TABLE FRONT EDGE