Gasketed plate heat exchangers range

Transcription

1 Technical specifications Gasketed plate heat exchanger (GPHE) data and dimensions T2 M3 TL3 T5 M6 Plate types T2B M3/M3D TL3B/TL3P/TL3BD T5M/T5B M6, M6M, M6MD Frame type FG FG FG FG FG FD Height, H [mm] Width, W [mm] Min standard length, L [mm] Max standard length, L [mm] Vertical port distance, VC [mm] Horizontal port distance, HC [mm] Max temperature [ C] Max pressure [barg] PV codes and directives* ALS ALS, PED, ASME ALS, PED, ASME ALS, PED, ASME ALS, PED, ASME PED, ASME Flange size DN50/2 DN50/2 Pipe size 3/4 1¼ 1¼ 2 2 Max flow rate [kg/s] Gasketed plate heat exchangers range T2 M3 T5 6:17

2 T2 Plate Heat Exchanger Applications General heating and cooling duties Standard design The plate heat exchanger consists of a pack of corrugated metal plates with portholes for the passage of the two fluids between which heat transfer will take place The plate pack is assembled between a fix frame plate and a movable pressure plate and compressed by tightening bolts The plates are fitted with a gasket which seals the interplate channel and directs the fluids into alternate channels The number of plates is determined by the flow rate, physical properties of the fluids, pressure drop and temperature program The plate corrugations promote fluid turbulence and support the plates against differential pressure The plate and the pressure plate are suspended from an upper carrying bar and located by a lower guiding bar Connections are located in the frame plate or, if either or both fluids make more than a single pass within the unit, in the frame and pressure plates T2B-FG Typical capacities Liquid flow rate Up to 2 kg/s (30 gpm), depending on media, permitted pressure drop and temperature program Plate types T2-B Frame types FG Working principle Channels are formed between the plates and the corner ports are arranged so that the two media flow through alternate channels The heat is transferred through the plate between the channels, and complete counter-current flow is created for highest possible efficiency The corrugation of the plates provides the passage between the plates, supports each plate against the adjacent one and enhances the turbulence, resulting in efficient heat transfer Flow principle of a plate heat exchanger 6:21

3 STANDARD MATERIALS Frame plate Mild steel, Epoxy painted Dimensions mm (inch) 140 (55 ) 50 (17 ) Nozzles Pipe: Stainless steel, Titanium Plates Stainless steel Alloy 316, Titanium Gaskets Nitrile, EPDM TECHNICAL DATA Pressure vessel code pvcals TM Mechanical design pressure (g) / temperature FG 16 MPa / 180 C 380 (15") 298 (117") 27 (11 ) Maximum heat transfer surface 10 m² (1076 sq ft) (54-98 ) ¾" Connections Straight pipe thread ISO-R ¾" Particulars required for quotation - Flow rates or heat load - Temperature program - Physical properties of liquids in question (if not water) - Desired working pressure - Maximum permitted pressure drop 6:22

4 M3 Plate Heat Exchanger Applications General heating and cooling duties Heating by means of steam Standard design The plate heat exchanger consists of a pack of corrugated metal plates with portholes for the passage of the two fluids between which heat transfer will take place The plate pack is assembled between a fix frame plate and a movable pressure plate and compressed by tightening bolts The plates are fitted with a gasket which seals the interplate channel and directs the fluids into alternate channels The number of plates is determined by the flow rate, physical properties of the fluids, pressure drop and temperature program The plate corrugations promote fluid turbulence and support the plates against differential pressure The plate and the pressure plate are suspended from an upper carrying bar and located by a lower guiding bar Connections are located in the frame plate or, if either or both fluids make more than a single pass within the unit, in the frame and pressure plates M3-FG Typical capacities Liquid flow rate Up to 4 kg/s (60 gpm), depending on media, permitted pressure drop and temperature program Plate types M3 and M3-X, where M3 provides parallel and M3-X diagonal flow (see figures on the next page) M3D, double wall plates Frame types FG Water heating by steam 50 to 250 kw 6:23

5 Working principle Channels are formed between the plates and the corner ports are arranged so that the two media flow through alternate channels The heat is transferred through the plate between the channels, and complete counter-current flow is created for highest possible efficiency The corrugation of the plates provides the passage between the plates, supports each plate against the adjacent one and enhances the turbulence, resulting in efficient heat transfer STANDARD MATERIALS Frame plate Mild steel, Epoxy painted Nozzles Carbon steel Pipe: Stainless steel, Titanium Flow principle of an M3 plate heat exchanger Plates Stainless steel Alloy 316, Titanium Gaskets (Clip-on) Nitrile, EPDM, Viton Other grades and material available on request TECHNICAL DATA Pressure vessel codes PED, ASME, pvcals Mechanical design pressure (g) / temperature FG PED, pvcals 16 MPa / 180ºC FG ASME 150 psig / 350ºF Maximum heat transfer surface 39 m 2 (40 sq ft) Flow principle of an M3X plate heat exchanger Dimensions 180 (709") 60 (24") Connections FG PED Size 1¼ Pipe, thread ISO-R 1¼ FG pvcals Size 1¼ Pipe, thread ISO-R 1¼ FG pvcals Size 1¼ Internal thread ISO-G 1¼, carbon steel FG ASME Size 1¼ Pipe, thread NPT 1¼ 480 (189") 357 (141") S4 S1 Particulars required for quotation - Flow rates or heat load - Temperature program - Physical properties of liquids in question (if not water) - Desired working pressure - Maximum permitted pressure drop - Available steam pressure 62 (24") S3 S2 173 (68") (165"-244") 40 (16") Measurements mm (inch) The number of bolts may vary depending on pressure rating 6:24

6 T5 Plate Heat Exchanger Applications General heating and cooling duties Standard design The plate heat exchanger consists of a pack of corrugated metal plates with portholes for the passage of the two fluids between which heat transfer will take place The plate pack is assembled between a fix frame plate and a movable pressure plate and compressed by tightening bolts The plates are fitted with a gasket which seals the interplate channel and directs the fluids into alternate channels The number of plates is determined by the flow rate, physical properties of the fluids, pressure drop and temperature program The plate corrugations promote fluid turbulence and support the plates against differential pressure The plate and the pressure plate are suspended from an upper carrying bar and located by a lower guiding bar Connections are located in the frame plate or, if either or both fluids make more than a single pass within the unit, in the frame and pressure plates T5-FG Typical capacities Liquid flow rate Up to 14 kg/s (222 gpm), depending on media, permitted pressure drop and temperature program Plate types T5-B, T5-M Frame types FG Working principle Channels are formed between the plates and the corner ports are arranged so that the two media flow through alternate channels The heat is transferred through the plate between the channels, and complete counter-current flow is created for highest possible efficiency The corrugation of the plates provides the passage between the plates, supports each plate against the adjacent one and enhances the turbulence, resulting in efficient heat transfer Flow principle of a plate heat exchanger 6:27

7 STANDARD MATERIALS Frame plate Mild steel, Epoxy painted Nozzles Carbon steel Pipe: Stainless steel, titanium Plates Stainless steel Alloy 316 / Alloy 304 Titanium Dimensions 245 (97") 100 (39") Gaskets Nitrile, EPDM TECHNICAL DATA Pressure vessel codes PED, ASME, pvcals Mechanical design pressure (g) / temperature FG pvcals 16 MPa / 180ºC FG PED 16 MPa / 160ºC FG ASME 150 psig / 356ºF 742 (292") 553 (218") 1155 (45") 55 (22") (ISO-G2") 115 (45")(ISO-R2") 2" Maximum heat transfer surface (59-138") T5-B 71 m² (764 sqft) T5-M 44 m² (474 sqft) Connections Straight threaded Size 50 mm ISO G2 Tapered threaded Size 50 mm ISO R2, NPT2 Threaded inlet port Size 50 mm ISO-G2 Measurements mm (inch) Type H W h T5-FG 737 (290") 245 (96") 1155 (45") Particulars required for quotation - Flow rates or heat load - Temperature program - Physical properties of liquids in question (if not water) - Desired working pressure - Maximum permitted pressure drop 6:28