SCHMEISER TILL AN BEDDER 2-BAR AND 4-BAR MODELS 12 FT. TO 20 FT. WIDE ASSEMBLY & PARTS MANUAL

Transcription

1 SCHMISR TILL AN BDDR -BAR AND -BAR MODLS FT. TO 0 FT. WID ASSMBLY & PARTS MANUAL T.G. SCHMISR CO., INC. P.O. BOX 07 FRSNO, CA 97 (559) 6- FAX (559) VRSION. FOR UNITS BUILT AFTR MAY 00 COPYRIGHT 0 T.G.SCHMISR CO., INC 07-0

2 INTRODUCTION Your Schmeiser Till An Bedder is designed to give you many years of dependable service. This manual has been prepared to instruct you in the safe and efficient operation of this machine. Read and study it thoroughly. Follow all instructions carefully. Should your Till An Bedder require replacement parts, go to your Schmeiser dealer. Always order genuine Schmeiser replacement parts. It is important that you complete and send in your Warranty Card because it is not valid unless it is on file at Schmeiser. If you need information not contained in this manual, contact your Schmeiser dealer. Space has been provided below for you to record the model number and serial number of your Till An Bedder. Be sure to bring this information with you to your dealer when ordering parts or attachments for your Till An Bedder. Thank you for buying a Schmeiser Till An Bedder. SRIAL NUMBR MODL NUMBR DAT PURCHASD DALR NAM

3 TABL OF CONTNTS Introduction... Table of Contents.. Safety Sheet... -Bar Till An Bedder Assembly.. 5 Assembly Instructions.. 6 -Bar Till An Bedder Pull Frame Assembly... -Bar Till An Bedder Pull Frame Assembly 9 Till An Bedder Hitch Assembly... 0 S-Tine Assembly... S-Tine Quantity Tables. S-Tine Bar Handle Assembly.... S-Tine Tie Clamp Assembly... Wheel Axle Bearing Assembly. 5 Till An Bedder Wheel Axle Assembly Rock Shaft to Main Frame Assembly... 7 Rock Shaft to Leveling Pipe Frame Assembly. Rock Shaft to Weeder Blade Assembly. 9 Bar Till An Bedder Hydraulic Cylinder Configurations Hydraulic Diagram for -Bar Till An Bedder Hydraulic Diagram for -Bar Till An Bedder Units... Hydraulic Diagram for -Bar Till An Bedder 6 Units Hydraulic Diagram for -Bar Till An Bedder 0 Units... Limited Warranty.. 5 Maintenance and Repair Record Notes.. 7

4 SAFTY The safe operation of any machinery is an important concern to farmers and manufactures. There are obvious and hidden potential hazards involved in the operation of this implement. Carefully read and follow all safety precautions before operation. Serious injury or death may occur unless care is taken to insure the safety of both the operator and any other persons in the area.. Never permit anyone to ride on or walk beside the implement when moving.. Never permit anyone to ride on tractor when implement is being moved.. When performing operating functions, never allow anyone to be near the implement or the tractor.. Do not enter tractor when tractor is moving. Avoid serious injury or death from contact with rotating tires. nter and exit the tractor only when it is completely stopped. 5. Be sure of water, gas, sewer, or electric line locations before operating implement. 6. When in transport, use accessory lights and devices for adequate warning to operators of other vehicles. Comply with all Federal, State and local laws when traveling on public roads. 7. Use Slow Moving Vehicle emblem for warning vehicles approaching from the rear.. When transporting, remember that the implement may be wider than your tractor and extreme care must be taken to allow for safe clearance. 9. Never allow inexperienced or untrained personnel to operate the implement or tractor without supervision. 0. When using compressed air to clean implement, wear safety glasses.. Check all fasteners for tightness or damage before and after operation. Repair immediately if required.. Store implement in a stable position. Insure that safety stands are extended and locked in place before detaching from tractor.

5 T. G. SCHMISR CO., INC. -BAR TILL AN' BDDR ASSMBLY 9 0 MANUAL CANISTR SRIAL PLAT Ref No. New Part No. Old Part No. Description Qty * Pull Frame. TBU-00B000 Pull Arm * Front Roller * Main Frame * S-Tine Frame Assembly * Leveling Pipe Frame * Rock Shaft Assembly * Rear Roller 9. SLL 5 SLL 5 Wheel Axle Bearing Assembly * Wheel Axle. GHC-500T SLL 0.5" x " Tie Rod Hydraulic Cyl. varies **. GWD-0LB Lockout Bar for " x 0" Hyd. Cyl. varies **. GHC-000T SLL 09 " x 0" Tie Rod Hydraulic Cyl. varies **. GHC-500W SLL 00.5" x " Welded Hydraulic Cyl. 5. GMB-HITCHCA CAT III Perfect Hitch * Part numbers vary depending on width and model number. ** Quantity of cylinders varies. See page 7 for all cylinder configurations. (559) 6- Fax (559)

6 S C IN IN I S R T. G. SCHMISR CO., INC. ASSMBLY INSTRUCTIONS STP C D. Install Pull Arms (A) as shown. Mount Pull Frame (B) to Pull Arms. Install bolts as shown: theads pointed upward.. Connect -/" X " Welded Hydraulic Cylinder(s) (C) on to Main Frame (D) and to Pull Frame Pivot Link(s) () as shown STP B A. Disconnect X 0 Hydraulic Cylinder (F) from Wheel Axle Transport Arm (G). Lift rear of machine approximately ' to '. Support machine securely to prevent falling.. Mount Wheels to Transport Axle Hubs (H). F G. Lower machine and reconnect X 0' Hydraulic Cylinder. H STP *. Mount Rock Shaft (J) to Main Frame (D). D. Mount Rear Leveling Bar (K) to Main Frame.. Mount -/ X Hydraulic Cylinder (L) to Main Frame and Rock Shaft. J K L * Refer to pages 5 and 6. (559) 6- Fax (559)

7 S C H IN M IN I S R T. G. SCHMISR CO., INC. STP. Secure Rear Roller Arms (M) to Main Frame (D).. Mount Rear Ring Roller Assembly (N) to Rear Roller Arms.. Rollers (N) can be mounted for either tilling or packing. When the curved teeth at the rear are pointed upward, the unit is ready for tilling, cultivating and mulching. When the curved teeth point downward, the unit is ready for packing and pulverizing. D M N PACKING DIRCTION TILLING DIRCTION STP 5. Mount Lead Hose Holders (P) to Brackets on Pull Frame *.. Insure that all hoses and fasteners are securely connected on Implement. P. Connect Lead Hoses (not included) to Hydraulic Manifold and Tractor. * Two cylinder configuration is shown. See page 7 for all configurations. (559) 6- Fax (559)

8 T. G. SCHMISR CO., INC. -BAR TILL AN' BDDR PULL FRAM ASS'Y Ref No. Part No. Description Qty.. GMB-HITCHCA CAT III Perfect Hitch. CSNC5096 /" X 6" NC Cap Screw. TB-00J00 Pull Frame. CSNC56 " X 7" NC Cap Screw 5. NYNUT-6NC " Nylon NC Hex Nut 6. TBU-00B000 Pull Arm 7. CSNC5 /" X " NC Cap Screw. HXNUT-NC /" NC Hex Nut 7 9. LWASHR- /" Lock Washer 7 (559) 6- Fax (559)

9 T. G. SCHMISR CO., INC. -BAR TILL AN' BDDR PULL FRAM ASSMBLY Ref No. Part No. Description Qty.. GMB-HITCHCA CAT III Perfect Hitch. CSNC5096 /" X 6" NC Cap Screw. TB-0J00 Pull Frame for ' and ' Units TB-0J00 Pull Frame for 6', ', and 0' Units. CSNC56 " X 7" NC Cap Screw 5. NYNUT-6NC " Nylon NC Hex Nut 6. TBU-00B000 Pull Arm 7. CSNC5 /" X " NC Cap Screw. HXNUT-NC /" NC Hex Nut 7 9. LWASHR- /" Lock Washer 7 (559) 6- Fax (559)

10 T. G. SCHMISR CO., INC. HITCH ASSMBLY C I IMPORTANT: INSTALL BOLTS AS SHOWN: THRADS POINTD UPWARD MAIN FRAM S S R 5 6 PULL FRAM IN IN 7 Ref No. New Part No. Description TB Qty. TB Qty.. GHC-500W.5" X " Welded Hydraulic Cyl.. GWD-5LB Lockout Bar For.5" X " Hydraulic Cyl.. TBU-00D000 Pivot Plate. CSNC56 " X 7" NC Cap Screw Gr NYNUT-6NC " NC Nylon Hex Nut 6. GPN-6X00 " X -/" Clevis Pin 7. GPN-0XC /" X -/" Cotter Pin. CSNC5006 CSNC5000 /" X -/" NC Cap Screw Gr. 5 (for -5/6" Bearings) 5/" X -/" NC Cap Screw Gr. 5 (for -/6" Bearings) LWASHR-0 LWASHR-0 /" Lock Washer (for -5/6" Bearings) 5/" Lock Washer (for -/6" Bearings) HXNUT-0NC HXNUT-0NC /" NC Hex Nut (for -5/6" Bearings) 5/" NC Hex Nut (for -/6" Bearings) CSNC560 " X " NC Cap Screw Gr. 5. NYNUT-6NC " NC Nylon Hex Nut. CSNC5 /" X 7" NC Cap Screw. HXNUT-NC /" NC Hex Nut 5. LWASHR- /" Lock Washer Specify Ring Size 5 /ft 5 /ft 7. TPP 57-5/6" Flange Bearing for Units 5' and under * TPP 5 -/6" Flange Bearing for Units 6' and over *. PMCK-500 Seal Kit for.5" x " Welded Hydraulic Cyl. 9. FWASHR-0 /" Flat Washer (for -5/6" Bearings) 6 6 FWASHR-0 5/" Flat Washer (for -/6" Bearings) 6 6 * NOT: Models, fabricated before July 997, use -/6" and -5/6" Pillow Block Bearings. (559) 6- Fax (559)

11 T. G. SCHMISR CO., INC. S-TIN ASSMBLY Ref No. New Part No. Old Part No. Description Qty. * SQT5W0 GST-505S GST-CL50 CBNC5006 LWASHR-0 HXNUT-0NC GST-550P GST-06BN SBM 550A SBM 55 SBM 55 -/" X -/" S-Tine Bar (specify length) /" X -/" S-Tine -/" S-Tine Bar Clamp /" X " Round Head Square Neck Bolt /" Lock Washer /" NC Hex Nut /" Standard S-Tine Point /" X -/" lliptical Head Metric Plow Bolt w/nut varies varies varies varies varies varies varies varies SBM 55 SBM 55 S-Tine Bar Clamp Assembly (includes items,, 5, and 6) * See page S-Tine Quantity Table for all quantities varies (559) 6- Fax (559)

12 T. G. SCHMISR CO., INC. S-TIN QUANTITY TABLS TABL FOR -BAR TILL AN' BDDR Ref. # Part Number Description Qty. ' ' 6' ' 0' TBU-00K0 GST-550S GST-CL50 CBNC5006 LWASHR-0 HXNUT-0NC GST-550P GST-06BN -/" X -/" S-Tine Bar /" X -/" S-Tine -/" Tool Bar Clamp /" X " Round Head Square Neck Bolt /" Lock Washer /" NC Hex Nut /" Standard S-Tine Point /" X -/" lliptical Head Metric Plow Bolt w/nut TABL FOR -BAR TILL AN' BDDR Ref. # Part Number Description Qty. ' ' 6' ' 0' TBU-00K0 GST-550S GST-CL50 CBNC5006 LWASHR-0 HXNUT-0NC GST-550P GST-06BN -/" X -/" S-Tine Bar /" X -/" S-Tine -/" Tool Bar Clamp /" X " Round Head Square Neck Bolt /" Lock Washer /" NC Hex Nut /" Standard S-Tine Point /" X -/" lliptical Head Metric Plow Bolt w/nut (559) 6- Fax (559)

13 T. G. SCHMISR CO., INC. S-TIN BAR HANDL ASSMBLY Ref No Part No. TBU-00K500 Description S-Tine Bar Handle TB Qty. TB Qty. GPN-X00 /" X -/" Clevis Pin GPN-0XC /" X -/" Cotter Pin TB-00K600 TB Front S-Tine Adjustment Lockout Arm - TB-00K600 TB Front S-Tine Adjustment Lockout Arm - Small - TB-00K700 TB Rear S-Tine Adjustment Lockout Arm - Large - HXNUT-0NC 5/" NC Hex Nut LWASHR-0 5/" Lock Washer SQT5W0 -/" X -/" S-Tine Bar (Specify Length) UBNC0XS 5/" X " Square Bend U-bolt (559) 6- Fax (559)

14 T. G. SCHMISR CO., INC. S-TIN TI CLAMP ASSMBLY Ref No. Part No. Description TB '-6' TB '-0' TB '-6' TB '-0'. HXNUT-0NC 5/" NC Hex Nut 6 6. LWASHR-0 5/" Lock Washer 6 6. SQT5W0 -/" S-Tine Bar (specify length). UBNC0XS 5/" X " Sq. Bend U-bolt 6 5. TBU-00L00 Tie Clamp Bracket 6 6. CSNC500 /" X -/" NC Cap Screw Gr FWASHR- /" Flat Washer NYNUT-NC /" NC Nylon Hex Nut FTB-00R0 S-Tine Tie Bar for -Bar Unit TB-00K0 S-Tine Tie Bar for -Bar Unit - - (559) 6- Fax (559)

15 T. G. SCHMISR CO., INC. WHL AXL BARING ASSMBLY 5 NOT: -nsure equal amount of space on each side before tightening U-bolts. -nsure equal number of threads on each side of U-Bolt. Ref No.. Part No. SLL 5 Description Bearing Cradle Cap Weldment Qty.. SLL 50 Bearing Cap Casting Machined. UBNC6R " Bearing U-bolt. HXNUT-6NC " NC Hex Nut 5. LWASHR-6 " Lock Washer SLL 5 SLL 5 U-Bolt Assembly (includes items,, and 5) Wheel Bearing Assembly (includes items,,,, and 5) (559) 6- Fax (559)

16 T. G. SCHMISR CO., INC. TILL AN' BDDR WHL AXL ASSMBLY Ref No Part No. Description TBU-0G000 Wheel Axle Weldment for TB ' to 6' and TB ' Units TB-G000 Wheel Axle Weldment for TB ' Units TB-0G000 Wheel Axle Weldment for TB 0' Units TB-G000 Wheel Axle Weldment for TB ' Units TB-6G000 Wheel Axle Weldment for TB 6' Units TB-G000 Wheel Axle Weldment for TB ' and 0' Units TBU-0G06 " x 0-/" Double nded Spindle for TB ('-') & TB ('-') TBU-0G06 " x -/" Double nded Spindle for TB (0') & TB (6'-0') GHB-6X6GSL Grease Seal WHB-0X06 /" x " UNF Wheel Bolts for 6 on 6 Std. Hub GHB-6X6ICN Inner Bearing Cone for 6 on 6 Std. Hub GHB-6X6IRC Inner Bearing Cup for 6 on 6 Std. Hub GHB-6X6STD Standard 6 on 6 Hub Assembly Complete (includes items,, 5, 6,, 9, ) GHB-6X6ORC Outer Bearing Cup for 6 on 6 Std. Hub GHB-6X6OCN Outer Bearing Cone for 6 on 6 Std. Hub GSP-SPWA Spindle Washer GSP-CANT Spindle Castle Nut GPN-0XC /6" x " Cotter Pin GHB-6X6CAP Hub Cap GWT x 5 Ply Tire with Wheel - for all TB & TB ' Units GWT x 5 Ply Tire with Wheel - for TB ' to 0' Units CSNC /6" x -/" NC Cap Screw LWASHR-07 7/6" Lock Washer HXNUT-07NC 7/6" NC Hex Nut SSNCS0X6 /" NC Square Head Set Screw Qty. (559) 6- Fax (559)

17 T. G. SCHMISR CO., INC. ROCK SHAFT TO MAIN FRAM ASS'Y MAIN FRAM * * Note orientation of Cylinder Anchor () in relation to Clevis Plates (*). Ref No. New Part No. Old Part No. Description. TBU-00L00 Hydraulic Cylinder Anchor Weld.. TBU-00L00 Rock Shaft Bracket Weldment. SQT5W0 -/" Main Tube (specify length). UBNC0XS TB-L7 5/" X " Square Bend U-bolt 5. LWASHR-0 5/" Lock Washer 6. HXNUT-0NC 5/" Standard NC Hex Nut 7. CSNC500 5/" X " NC Cap Screw. GHC-500T SLL 0.5" X " Tie Rod Hydraulic Cyl. 9. GPN-6X0 " X " Clevis Pin 0. GPN-0XC /" X -/" Cotter Pin. PMCK-500 Seal Kit for.5" x " Hydraulic Cyl. TB TB '- 6' TB '- 0' (559) 6- Fax (559)

18 T. G. SCHMISR CO., INC. ROCK SHAFT TO LVLING PIP FRAM ASS'Y * LVLING PIP FRAM * Note orientation of Cylinder Anchor (*) in relation to Clevis Plates (). Ref No. Part No. Description. TBU-00L00 Linkage Clevis Plates Weldment. SQT5W0 -/" Main Tube (specify length). UBNC0XS 5/" X " Square Bend U-bolt. LWASHR-0 5/" Lock Washer 5. HXNUT-0NC 5/" Standard NC Hex Nut 6. TBU-00L500 Leveling Bar Link 7. CSNC500 /" X -/" NC Cap Screw. FWASHR- /" Flat Washer 9. NYNUT-NC /" NC Nylon Hex Nut 0. GPN-6X00 " X -/" Clevis Pin. GPN-00LYN /" X " Lynch Pin Qty. (559) 6- Fax (559)

19 T. G. SCHMISR CO., INC. ROCK SHAFT TO WDR BLAD ASS'Y * * Note orientation of Cylinder Anchor (*) in relation to Clevis Plates (). Ref No. Part No. Description. TBU-00L00 Linkage Clevis Plates Weldment. SQT5W0 -/" Main Tube (specify length). UBNC0XS 5/" X " Square Bend U-bolt. LWASHR-0 5/" Lock Washer 5. HXNUT-0NC 5/" Standard NC Hex Nut 6. TBU-00L600 TB Weeder Blade Assembly Link 7. TBU-00L700 TB Weeder Blade Middle Brace Wldm.. TBU-00L00 TB Weeder Blade Side Brace Wldm. 9. TBU-00L90 TB Weeder Blade ye Bolt 0. GPN-6X00 " X -/" Clevis Pin. GPN-00LYN /" X " Lynch Pin. HXNUT-NC /" NC Hex Nut. CSNC500 /" X -/" NC Cap Screw. NYNUT-NC /" NC Nylon Lock Hex Nut (559) 6- Fax (559) Qty.

20 T. G. SCHMISR CO., INC. -BAR TILL AN' BDDR HYD. CYL. CONFIGURATIONS ' AND ' UNITS 6' UNITS ' AND 0' UNITS Ref No. Old Part No. New Part No. (559) 6- Fax (559) Description. SLL 00 GHC-500W.5" X " Welded Hydraulic Cylinder. SLL 0 GHC-500T.5" X " Tie Rod Hydraulic Cylinder or. SLL 09 GHC-000T " X 0" Tie Rod Hydraulic Cylinder or Qty.

21 T. G. SCHMISR CO., INC. -BAR TILL AN' BDDR HYDRAULIC DIAGRAM PULL FRAM -/" x " WLDD CYL. TRANSPORT AXL " x 0" HYD. CYL. B B B B FRONT OF UNIT G G # # F F # # LVLING BAR -/" x " HYD. CYL. A A G F C # G F C #5 NOT: Typical for all -Bar Till An' Bedder models. FITTINGS (ALL FITTINGS AR 000#) A. () MB-MJ-- ADAPTR B. () MB-MJ-90-- LBOW C. () MJ-MJ-- BULKHAD STRAIGHT. () MJ- BULKHAD T F. () HN- BULKHAD LOCK NUT G. () FJ- CAPS HOSS (ALL HOSS AR /" Ø) #. () FJX-FJX " LONG #. () FJX-FJX 7" LONG #. () FJX-FJX 0" LONG #. () FJX-FJX " LONG #5. () FJX-FJX 9" LONG HYDRAULIC CYLINDRS () -/" x " Tie Rod Cylinder () -/" x " Welded Cylinder () " x 0" Tie Rod Cylinder (559) 6- Fax (559)

22 T. G. SCHMISR CO., INC. -BAR TILL AN' BDDR HYD. DIA. '-' UNITS /" x " HYD. CYL. " x 0" HYD. CYL. PULL FRAM TRANSPORT AXL A RSTRICT OIL GOING INTO CYLINDR RSTRICT OIL GOING OUT OF CYLINDR FLOW F H B MANIFOLD B B /" x " HYD. CYL. LVLING BAR F H B # C # B H F FLOW FLOW G A A D # # #6 #5 #9 #9 C #0 D # #7 #0 D RSTRICT OIL GOING OUT OF CYLINDR /" x " HYD. CYL. PULL FRAM G D XT. RT. RT. XT. FITTINGS: A. () MB-MJ 90º LBOW B. (5) MB-MJ STGHT LINK C. () MJR CROSS FITTING D. () HN BULKHAD LOCK NUT. () MJ-MJH BULKHAD STRGHT F. () MB-MB 90º LBOW G. () FJX-FJX COUPLING H. () FB IN-LIN RSTRICTORS W/ /" Ø HOL NOT: ALL FITTINGS 000# CAP. HYD. CYLINDRS () /" x " TI ROD CYL. () /" x " WLDD CYL. () " x 0" TI ROD CYL. HOSS: # - () FJX-FJX " LONG # - () FJX-FJX 0" LONG # - () FJX-FJX 5" LONG # - () FJX-FJX 5" LONG #5 - () MJ-FJX 7" LONG #6 - () MJ-FJX 0" LONG #7 - () MJ-FJX 0" LONG # - () MJ-FJX 6" LONG NOT: ALL HOSS AR /" Ø PIP LINS: #9 - () STL TUB, 7" LONG #0 - () STL TUB, 5" LONG ALL STL TUBS AR FJX-FJX (559) 6- Fax (559)

23 T. G. SCHMISR CO., INC. -BAR TILL AN' BDDR HYD. DIA. 6' UNIT RAR #0 #9 B B /" x " HYD. CYL. LVLING BAR # J #6 " x 0" HYD. CYL. TRANSPORT AXL A J A FLOW #7 #5 FLOW F H B B H F # # # # " x 0" HYD. CYL. TRANSPORT AXL RSTRICT OIL GOING INTO CYLINDR RSTRICT OIL GOING OUT OF CYLINDR /" x " HYD. CYL. PULL FRAM F A MANIFOLD D D # G # H B D B H FLOW FLOW C # # G FRONT D RT. XT. XT. BOTTOM RT. TOP FITTINGS: A. () MB-MJ 90º B. (6) MB-MJ ADAPTR C. () MJ CROSS FITTING D. () HN BULKHAD LOCK NUT. () MJ-MJ BULKHAD ADAPTR F. () MB-MB 90 LBOW G. () FJX-FJX-- COUPLING H. () FB INLIN RSTRICTORS W/ /" Ø HOL J. () MJ T FITTING FRONT OF UNIT C RSTRICT OIL GOING INTO CYLINDR RSTRICT OIL GOING OUT OF CYLINDR F A HOSS: # - () FJX-FJX 6 LONG # - () FJX-FJX LONG # - () FJX-FJX 67" LONG # - () FJX-FJX 60" LONG #5 - () FJX-FJX 5" LONG #6 - () FJX-FJX 0" LONG #7 - () FJX-FJX 95 LONG # - () FJX-FJX " LONG #9 - () MJ-FJX 5" LONG #0 - () MJ-FJX 50" LONG /" x " HYD. CYL. PULL FRAM PIP LINS: # - () STL TUB FJX-FJX 5" LONG NOT: ALL HOSS AR /" Ø NOT: ALL FITTINGS 000# CAP. (559) 6- Fax (559)

24 T. G. SCHMISR CO., INC. -BAR TILL AN' BDDR HYD. DIA. '-0' UNITS RAR LVLING BAR /" x " HYD. CYL. B # G #0 B LVLING BAR /" x " HYD. CYL. TRANSPORT AXL " x 0" HYD. CYL. A F B FLOW H B # # #7 G G #9 G B #6 #5 B A FLOW H F TRANSPORT AXL " x 0" HYD. CYL. RSTRICT OIL GOING INTO CYLINDR RSTRICT OIL GOING INTO CYLINDR # # # # RSTRICT OIL GOING OUT OF CYLINDR MANIFOLD D D RSTRICT OIL GOING OUT OF CYLINDR PULL FRAM /" x " HYD. CYL. F A H B # FLOW # C C J D # B FLOW # H F A PULL FRAM /" x " HYD. CYL. FRONT RT. XT. BOTTOM PIP LINS: # - () STL TUB FJX-FJX 5" LONG J RT. D FRONT OF UNIT XT. TOP FITTINGS: A. () MB-MJ 90º B. () MB-MJ STGHT LINK C. () MJ CROSS FITTING D. () HN BULKHAD LOCKING NUT. () MJ-MJ STRAIGHT BULKHAD LINK F. () MB-MB 90 LBOW G. () MJ T FITTINGS H. () FB INLIN RSTRICTORS W/ /" Ø HOL J. () FJX-FJX COUPLING NOT: ALL FITTINGS 000# CAP. NOT: ALL HOSS AR /" Ø HOSS: # - () FJX-FJX 90 6" LONG # - () FJX-FJX 90 " LONG # - () FJX-FJX 67" LONG # - () FJX-FJX 60" LONG #5 - () FJX-FJX 5" LONG #6 - () FJX-FJX 0" LONG #7 - () FJX-FJX 95" LONG # - () FJX-FJX " LONG #9 - () MJ-FJX 5" LONG #0 - () MJ-FJX 50" LONG # - () FJX-FJX 75" LONG # - () FJX-FJX 5" LONG (559) 6- Fax (559)

25 T.G. SCHMISR CO., INC. Limited Warranty Statement T. G. Schmeiser Co., Inc. warrants each new Schmeiser product to be free from defects in material and workmanship. This warranty is applicable only for the normal service life expectancy of the product or components, not to exceed twelve () consecutive months from the date of delivery of the new Schmeiser product to the original purchaser. Genuine T. G. Schmeiser Co., Inc. replacement parts and components will be warranted for 90 days from date of purchase, or the remainder of the original equipment warranty period, whichever is longer. Under no circumstances will it cover any merchandise or components thereof, which, in the opinion of the company, has been subjected to misuse, unauthorized modifications, alteration, an accident or if repairs have been made with parts other than those obtainable through T. G. Schmeiser Co., Inc. The Company in no way warrants engines, batteries, cylinders, tires or other trade accessories since these items are warranted separately by their respective manufacturer. xpendable components such as points, shanks, blades, rings, bearings, teeth, and the like are excluded from this warranty. Our obligation under this warranty shall be limited to repairing or replacing, free of charge to the original purchaser, any part that, in our judgment, shall show evidence of such defect, provided further that such part shall be returned within thirty (0) days from date of failure to T. G. Schmeiser Co., Inc., routed through the dealer and distributor from whom the purchase was made, transportation charges prepaid. This warranty shall not be interpreted to render T. G. Schmeiser Co., Inc. liable for injury or damages of any kind or nature to person or property. This warranty does not extend to the loss of crops, loss because of delay in harvesting, or any expense or loss incurred for labor, substitute machinery, rental or for any other reason. xcept as set forth above, T. G. Schmeiser Co., Inc. shall have no obligation or liability of any kind on account of any of its equipment and shall not be liable for special or consequential damages. T. G. Schmeiser Co., Inc. makes no other warranty, expressed or implied, and, specifically, T. G. Schmeiser Co., Inc. disclaims any implied warranty or merchantability or fitness for a particular purpose. Some states or provinces do not permit limitations or exclusions of implied warranties or incidental or consequential damages, so the limitations or exclusion in this warranty may not apply. This warranty is subject to any existing conditions of supply, which may directly affect our ability to obtain materials or manufacture replacement parts. T. G. Schmeiser Co., Inc. reserves the right to make improvements in design or changes in specifications at any time, without incurring any obligation to owners of units previously sold. No one is authorized to alter, modify or enlarge this warranty nor the exclusion, limitations and reservations. WARRANTY VOID IF NOT RGISTRD WITHIN 0 DAYS OF PURCHAS DAT 5

26 SCHMISR TILL AN' BDDR MAINTNANC AND RPAIR RCORD Date of Service or Repair Performed Parts Service Replaced 6

27 Notes 7

28 Notes