AGCO Conversion Manual a HEADSIGHT.COM

Transcription

1 AGCO 3300 Conversion Manual a HEADSIGHT.COM

2

3 About Headsight Headsight Contact Info Headsight, Inc B Road Bremen, IN Phone: Fax: Web: Technical Assistance Phone: About this Manual How to use this manual The instructions in this manual are in the order that they should be completed for new installations. Complete all applicable instructions in each section before proceeding. Note that some sections are labeled to indicate they only apply to certain machines or applications. An index is available in the front of the manual to help find technical information for previously installed systems. This icon designates information of which you should take note. This icon indicates a special tool needed for a given task. This icon designates an important instruction. Disclaimers Headsight, Horizon, Pinpoint, Insight, Foresight, Feathersight Truesense and Truesight are trademarks of Headsight, Inc. All other trademarks are property of their respective owners. Suggestions If you have any suggestions to improve this manual please call or info@headsight. com. Headsight s products are protected by one or more of the following US Patents , , , and other patents pending. Copyright Headsight, Inc i

4 Table of Contents About Headsight i About this Manual i 1 Identify the components 2 Sensor (Optional) 4 Insight Box Mounting 7 Header Adapter 7 Power Adapter : Late Models 7 Power Adapter : Early Models 8 Sensor Adjustment 9 Changing Swing 9 Increasing or Decreasing Voltage 9 Sensor Extensions 10 Parts 11 KIT - HT Insight Kit 12 Corn Sensor HT STATEMENT OF LIMITED WARRANTY 15 ii

5 Before working under header always: 1. Perform all combine and header manufacturer safety precautions for servicing header. 2. Insert stop to prevent movement of header. 3. Turn off combine and remove key from ignition. 4. Set combine parking brake. 5. Disconnect all drive shafts from the header. 1

6 Identify the components 1. Insight Interface Insight Mounting kit- BC-BOX 2. Insight Adapter harness QC1-AG12-XX Main Harness 3. Power adapter, late model PFI-AG3300-P MF 95xx & up Challenger 5x0C & up, Gleaner S9x & up 4. Power adapter, early model PFI-AG13-P MF 9x95 & prior Challenger 6x0B & prior Gleaner S8x & prior 2

7 5. OPTIONAL: HT2291 Sensor kit adds 3rd or 5th sensor 3

8 Sensor (Optional) 1. Install the sensor into the Mounting Bracket. Sensor HT2290 mount B2290 bolt kit 2. Remove the OEM skid shoe assembly and reinstall the front 2 bolts. 3. Mount the sensor assembly into the Snout. B2290 Bolt Kit 4. Remove the black plug from the end of the extension harness. Release the seal retainer Use the WeatherPack Removal Tool 4

9 5. Route the loose pins end of the extension harness up thru the snout mounting plate from back to front. 6. Reinstall the connector removed in Step 4. Flare latch wings on terminals slightly A- Black B- White C- Green Snap seal retainer shut 7. Route harness OVER pivot rod (See step 10 below) and forward to sensor. 8. Connect extension harness to sensor Leave a bit of slack in the sensor tail Secure connection with clamps on both sides Make sure connector is tucked into corner of snout Make sure connector latch faces UP against snout 9. Working from sensor back, secure sensor harness with clamps. 5

10 10. Secure harness around pivot as shown. Make sure to leave enough slack for full motion of snout 11. Route the cable around rear hinge as shown. Leave enough slack for motion Use zip tie on bar Secure to lower plate with clamp and bolt 12. Route harness OVER the drive shaft assembly under trough, secure as necessary. 13. Follow existing cables to left side of header. 14. Connect extension harness to S84 on Insight adapter harness. 6

11 Insight Box Mounting 1. Mount Insight to existing slotted holes on back sheet of header. BCBOX Bolt Kit Header Adapter 1. Locate the adapter harness: QC1-AG12-XX. 2. Connect Y101 to the bottom of the Insight. 3. Locate the OEM connector TO HEADER MOD - X (12 pin Receptacle). 4. Disconnect jumper plug or adapter to AGCO module from X Store jumper in combine. 5. Connect Y548 to X If installing optional 3rd or 5th sensor, connect center sensor harness to S84. Power Adapter : Late Models 1. Choose Power Adapter (see Identify the Components). 2. Locate PFI-AG3300-P. 3. Locate the CENTER POS SEN - X (6 pin plugs for steering sensor) under center of head. 4. Tee power adapter Y573-Y574 into OEM plugs. 5. Route Y520 back toward the Insight box, following OEM harness. 6. Route Y521 on the Insight adapter down toward Y520, following OEM harness. 7. Connect Y520 to Y Make sure to tie up all cabling securely. 7

12 Power Adapter : Early Models 1. Locate power wire PFI-AG13-P. 2. Connect the power to a fuse in the cab fuse compartment. 3. If your fuse panel has spare fuse ¼ spades, remove the clip and connect the ¼ spade directly to the Spare fuse blade. 4. Otherwise snap clip around the output (fused) side of the AHC fuse. 5. Connect the ground ring to a bolt in the fuse compartmant. 6. Route Y520 out of the cab and down the feeder house to beside the single point. Route Y521 on the Insight adapter up the single point harness to beside the single point. 7. Connect Y520, Y521 (you will need to disconnect everytime the header is disconnected.) 8. Make sure to tie up all cabling securely. 8

13 Sensor Adjustment Insert header stop to prevent movement Changing Swing 1. Loosen the bolt A holding down stop. 2. Slide the down stop to new position in slotted hole. Raising down stop will increase voltage swing and allow higher maximum cutting height Lowering the down stop will decrease total voltage swing and help prevent arm from stabbing the ground when the headers is lowered A Calibration Increasing or Decreasing Voltage 1. Loosen sensor mounting nuts B. 2. Twist sensor to new position using slotted mounting holes. Twisting sensor clockwise will lower voltage Twisting sensor counterclockwise will increase voltage 3. Retighten the nuts B. B B 9

14 Sensor Extensions Headsight recommends using the lowest extension setting that allows you to run as high as you desire. Increasing the length of the extension will reduce header control sensitivity. 1. Remove flange locknut then remove arm and spring. 2. Install extension to sensor assembly with previously removed spring and flange locknut. 3. Install arm in extension with two bolts and nuts as pictured at desired length. Headsight does not recommend extensions unless you need to run higher If you desire to operate header higher than sensors will allow, you may add extensions 10

15 Parts KIT - HT ITEM QTY. PART NUMBER DESCRIPTION 1 1 HT2000-B Corn Sensor 2 1 B2290 Mounting Hardware 3 1 HT2290 Mounting Bracket 4 1 BCS1 Hardware/Extension Kit Pin Removal Tool 6 1 PFB17 Extension Harness Parts 11

16 Insight Kit a 4b ITEM QTY. PART NUMBER DESCRIPTION 1 1 INSIGHT Insight Controller 2 1 QC1-SG12-xx Main Harness 3 1 BCIBOX Mounting Hardware 4a AR PFI-AG3000-P Power Wire 4b AR PFI-AG13-P Power Wire Parts 12

17 DATE 4 3 UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES DIMENSIONS W/O TOL ARE BASIC THIRD ANGLE PROJECTION SHEET 1 OF 1 HEADSIGHT INC. THE INFORMATION CONTAINED ON THIS DRAWING IS PROPRIETARY TO HEADSIGHT, INC. ANY UNAUTHORIZED USE OF SUCH CONTENTS IS STRICTLY PROHIBITED. HT2000_PARTS 2 1 CHG LEVEL C H G F E D C B A Parts H G F E D C B A ITEM NUMBER PART NUMBER DESCRIPTION QUANTITY 1 HT2125 PIVOT ARM 1 2 HT2111 SPRING 1 3 HT2131 BUSHING BLUE 1 4 HT2132 BUSHING WHITE 1 5* HT2139 BUSHING ASSEMBLY WITH SEALS SNAP RING E-CLIP 1 7 HT2120 CORN BODY 1 8 HT2128 SENSOR M5x20 HEX BOLT 2 10 HT2130 SHIELD (OPTIONAL) M8x12 FLANGE BOLT 1 11A M8x12 FLANGE BOLT (OPTIONAL) 1 12 HT2105 STOP /16-18 FLANGE LOCK NUT 1 14 HT2110 SPRING /8-16 SERRATED FLANGE NUT 2 16 HT2117 EXTENSION /8-16x1-3/8 HEX BOLT 2 18 HT2113-B HT2113-Y 19 HT2000-B HT2000-Y 8 7 POLY ARM BLACK POLY ARM YELLOW COMPLETE SENSOR ASSEMBLY BLACK COMPLETE SENSOR ASSEMBLY YELLOW (ASSM EXCLUDES 10, 11A, 15, 16 & 17) * 5* 4 5* NOTE: SENSOR CALIBRATION TARGET HIGH VOLTAGE = 4.00V (ACCEPTABLE RANGE 3.95V V) HT2000_PARTS 8 9 5* A MATERIAL N/A JAN 30, 17 CORN SENSOR PARTS, HALL EFFECT 04 13

18 14 This Page Is Intentionally Left Blank

19 STATEMENT OF LIMITED WARRANTY For Headsight Products Headsight Inc. (Headsight) warrants its new products to be free from defects in material and workmanship for a period of twelve (12) consecutive months following the date of purchase by the retail purchaser. Headsight Inc. (Headsight) warrants its new corn sensors assemblies for a period of thirty-six (36) months. Headsight warrants genuine Headsight replacement parts and components to be free from defects in material and workmanship for a period of six (6) consecutive months following the date of purchase or the remainder of the original equipment warranty period, whichever is longer. Headsight s obligation under these warranties shall be limited to repairing or replacing, free of charge to the original purchaser, any part that, in Headsight s judgment, shows evidence of such defect. Limitations to Warranty This warranty does not cover: Warranty claims directly resulting from improper installation of the product. Any product damaged by accident, abuse, misuse, or negligence after shipment from Headsight. Any unauthorized product alteration or modification. Any unauthorized repairs made with parts other than genuine Headsight parts. Any repairs performed by anyone other than Headsight or an authorized Headsight dealer unless specifically authorized by Headsight. Warranty Procedure Troubleshooting should be done between farmer/dealer and Headsight through our technical Labor reimbursement will occur only pre-arranged through Headsight technical assistance and be scheduled to a flat rate basis or reasonable time allowance in Headsight s judgment. There is no mileage reimbursement. Diagnostic time will not be reimbursed except in pre-arranged circumstances. Warranty claims should be on typical dealer service work order with a number and name to be attached for any future correspondence. All warranty work must be performed, and claims submitted, within thirty (30) days of the occurrence of the claim and within the warranty period. All parts removed during warranty repair must be returned to Headsight with Headsight s Return Form within thirty (30) days of the occurrence of the claim and within the warranty period. Headsight, Inc. reserves the right to either inspect the product at the original retail purchaser s location or require it to be returned to Headsight, Inc. for inspection. Limitation of Liability Headsight makes no express warranties other than those, which are specifically described herein. Any description of the goods sold hereunder, including any reference to buyer s specifications and any descriptions in circulars and other written material published by Headsight is for the sole purpose of identifying such goods and shall not create an express warranty that the goods shall conform to such description. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED. There are no implied warranties of merchantability or fitness of a particular purpose. This warranty states Headsight s entire and exclusive liability and buyer s exclusive remedy or any claim for damages in connection with the sale of furnishing of Headsight products, their design, suitability for use, installation or operation, or for any claimed defects herein. HEADSIGHT WILL IN NO EVENT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES WHATSOEVER, NOR FOR ANY SUM IN EXCESS OF THE PRICE RECEIVED FOR THE GOODS FOR WHICH LIABILITY IS CLAIMED. No representative of Headsight nor any dealer associated with Headsight has the authority to change the items of this warranty in any manner whatsoever, and no assistance to purchaser by Headsight in the repair of operation of any Headsight product shall constitute a waiver of the conditions of this warranty, nor shall such assistance extend or revive it. Headsight reserves the right to make improvements in design or changes in specifications at any time, without incurring any obligation to owners of units previously sold. Warranty: 1/

20 P F B Rd Bremen, IN info@headsight.com