System Verification Checklist

Size: px

Start display at page:

Download "System Verification Checklist"

Gwendolyn McCarthy
5 years ago
Views:

1 Manufacturer: Model Number: Unit Identification/Installation Equipment and Piping Identification Affixed, Specification Comply with Equipment Manufacturer s Written Installation Instructions Extra Materials (3) Sets of Filters, Spec A (1) Set of Fan Belts, Spec A Unit Mounting Concrete Equipment Pad (4 ), M-402/Note 11, M-502/Detail 3E, Spec A Access Access Doors Provided As Specified, Spec Unit Access Provided for Maintenance and Repair, Spec , C Chilled Water Coil Piping Unions Installed, P/T Plugs Installed, Temperature Control Valve Installed,, M-702/Detail 1A, Spec I Shutoff (Isolation) Valves Installed, Strainer with Blowdown Valve On Inlet, Manual Balancing Valves Installed, Drain With Hose End/Cap and Drain Valve, Thermometers Installed, Pressure Gauge Installed with Ball Valves, Remarks: IC-Installing Contractor; -Sheet Metal Contractor; -Mechanical Contractor; -Electrical Contractor; -Controls Contractor Page 1 of 7

2 Chilled Water Coil Piping (continued) Grommets Installed at Pipe Penetrations, Manual Air Vent Installed, M-501/Details 5B, 2A Heating Coil Piping Unions Installed, P/T Plugs Installed, Temperature Control Valve Installed,, M-702/Detail 1A, Spec I Shutoff (Isolation) Valves Installed, Strainer with Blowdown Valve On Inlet, Manual Balancing Valves Installed, Drain With Hose End/Cap and Drain Valve, Thermometers Installed, Pressure Gauge Installed with Ball Valves, Grommets Installed at Pipe Penetrations, Manual Air Vent Installed, M-501/Details 5B, 2A Preheat Coil Piping Unions Installed, P/T Plugs Installed, Temperature Control Valve Installed,, M-702/Detail 1A, Spec I Shutoff (Isolation) Valves Installed, Strainer with Blowdown Valve On Inlet, Manual Balancing Valves Installed, Remarks: IC-Installing Contractor; -Sheet Metal Contractor; -Mechanical Contractor; -Electrical Contractor; -Controls Contractor Page 2 of 7

3 Preheat Coil Piping (continued) Drain With Hose End/Cap and Drain Valve, Thermometers Installed, Pressure Gauge Installed with Ball Valves, Grommets Installed at Pipe Penetrations, Manual Air Vent Installed, M-501/Details 5B, 2A Pre-Heating Pump HWP-AHU-1 Mfr./Model #: Equipment and Piping Identification Affixed, Specification Comply with Equipment Manufacturer s Written Installation Instructions Install Pump with Motor and Pump Shafts Vertical, Spec E Spring Vibration Isolation Hangers Installed, M-501/Detail 1C, Spec E Unions Installed, M-501/Detail 1C Pressure Gauge w/ Shutoff Cocks Installed, M-501/Detail 1C Isolation Valves Installed, M-501/Detail 1C Strainer with Blowdown Valve Installed, M-501/Detail 1C Check Valve Installed, M-501/Detail 1C Condensate Drain Pan Drain Pan and Piping, Spec , 2.6.D, 3.3, M-501/Detail 3A Filter(s) Section Spec EA Filters Installed MERV 8 Rating, M-503, Spec Pre-Filters Installed MERV 8 Rating, Spec Remarks: IC-Installing Contractor; -Sheet Metal Contractor; -Mechanical Contractor; -Electrical Contractor; -Controls Contractor Page 3 of 7

4 Filter(s) Section (continued) Final Filters Installed MERV 14 Rating, Spec Differential Pressure Filter Switches, M702/Detail 1A, Spec I.3 Supply Fan Spec Perforated Liner Provided, M-601 Return Fan Spec Perforated Liner Provided, M-601 Enthalpy Heat Wheel ERU-1E/ERU-1S Spec , M-702/Detail 1A Sensible Heat Wheel SW-1E/SW-1S Spec , M-702/Detail 1A Dampers/Ductwork OA Motorized Damper (OAD-D) and Actuator(s), M-702/Detail 1A, Spec , 3.1.C EA Motorized Damper (EXA-D) Provided by Manufacturer and Actuator(s), M-702/Detail 1A, Spec , 3.1.C Ductwork Provided with Support From Structure As Specified, Spec Final Duct Connections With Flexible Connections, Spec Duct Silencer RA1-1 Installed, M-601 Duct Silencer SA1-1 Installed, M-601 Electrical Furnish and install all disconnect switches, N circuit protection, motor controllers, relays, devices, components as required for unit to provide complete and operable electrical system Supply Fan Motor Starter (MS-D6) Wired to Panel 34D1/Circuits 1,3,5, EP1E3, E-603, Spec , 3.3 T T Remarks: IC-Installing Contractor; -Sheet Metal Contractor; -Mechanical Contractor; -Electrical Contractor; -Controls Contractor Page 4 of 7

5 Electrical (continued) Return Fan Motor Starter (MS-D7) Wired to Panel 34D1/Circuits 7,9,11, EP1E3, E-603, Spec , 3.3 HWP-AHU-1 Motor Starter (MS-D13) Wired to Panel 34D1/Circuits 14,16,18, EP1E3, E-603, Spec , 3.3 Energy Recovery Wheel Motor Starter (MS-D8) Wired to Panel 34D1/Circuits 13,15,17, EP1E3, E- 603, Spec , 3.3 Unit Lights Provided, Spec A, 115V GFCI Receptacle(s) Provided for Unit, Spec Junction Box for Lighting and Receptacles Connected to Panel 32D1/Circuit 11, EP1E3/Note 29 Grounding For Components and Unit, Spec Controls HVAC DDC Controller, Spec C Low Limit Freezestat; Hardwired to Unit Fan(s), M-702/Detail 1A, Spec E, 3.2.H.12 Supply Air Duct Smoke Detector (SA-SD) Hard Wired to Unit Fan(s), M-702/Detail 1A Return Air Duct Smoke Detector (RA-SD) Hard Wired to Unit Fan(s), M-702/Detail 1A Sensors Pre-Heat Coil Discharge Temperature Sensor, M702/Detail 1A, Spec H.10 Cooling Coil Discharge Temperature Sensor, M702/Detail 1A, Spec H.10 Relief Exhaust Temperature Sensor (RXH EA-T), M702/Detail 1A, Spec H.10 Enthalpy Wheel Discharge Temperature Sensor (EWDA-T), M702/Detail 1A, Spec H.10 Remarks: IC-Installing Contractor; -Sheet Metal Contractor; -Mechanical Contractor; -Electrical Contractor; -Controls Contractor Page 5 of 7

6 Sensors (continued) Exhaust Discharge Temperature Sensor (EXH DA-T), M-702/Detail 1A, Spec H.10 Supply Air Temperature Sensor (SADA-T), Return Air Temperature Sensor (RA-T), Outside Air Global Temperature Sensor (OA-T), Outside Air Temperature Sensor (OA-T), Supply Air Humidity Sensor (SA-H), M-702/Detail 1A, Spec C Return Air Humidity Sensor (RA-H), M-702/Detail 1A, Spec C Sensible Heat Wheel Temperature Sensor (SHW DAT), M-702/Detail 1A, Spec H.10 Variable Frequency Drives Exhaust Air Fan VFD Installed, M-702/Detail 1A, Spec , A, Outside Air Fan VFD Installed, M-702/Detail 1A, Spec , A, Supply Air Fan VFD Installed, M-702/Detail 1A, Spec , A, Enthalpy Heat Wheel VFD Installed, M-702/Detail 1A, Spec , A, Sensible Heat Wheel VFD Installed, M-702/Detail 1A, Spec , A, Remarks: IC-Installing Contractor; -Sheet Metal Contractor; -Mechanical Contractor; -Electrical Contractor; -Controls Contractor Page 6 of 7

7 Variable Frequency Drives (continued) VFD s Provided with Shaft Grounding Rings, M-601 Identify VFD s, Components And Control Wiring, Spec , A Operating Instructions Mounted on Front of VFD s, Spec B Outside Air Fan VFD Wired, Spec , Exhaust Air Fan VFD Wired, Spec , Supply Air Fan VFD Wired, Spec , Notes: Remarks: IC-Installing Contractor; -Sheet Metal Contractor; -Mechanical Contractor; -Electrical Contractor; -Controls Contractor Page 7 of 7

Air Handling Unit Construction Checklist

Air Handling Unit Construction Checklist Project: Date: AHU Tag: Location: Submittal / Approvals Submittal. The above equipment and systems integral to them are complete and ready for functional testing.