Transcription

1

2

3

4

5

6 Project: Customer: Engineer: Pump Manufacturer: Drawing Submittal Package Model GPL Limited Service Full Voltage Across the Line Start Electric Pump Controller Contents: Submittal Data Sheets Dimensional Data Wiring Schematics Field Connections NOTE: The drawings included in this package are for controllers covered under our standard offering. Actual AS BUILT drawings may differ from what is shown in this package March 2012

7 Submittal Data Sheet Model GPL Electric Pump Controller From normal incoming power through Circuit Breaker (CB)* CR4 3L2 3L1 1M 4L2 1M T2 T1 M 3L1 3L2 600 Across-the-line starting Starting Method: Full Voltage Across the line (Direct on line) Typical Voltage Applied at Start: 100% Inrush Current: 6 x normal load current Starting Torque: 100% Motor Type: Across the line (Direct on line) No. of Contactors: 1 at 100% of horsepower Line current % of full load Locked rotor current No. of Motor Connections & Sizing: 3 at 100% of Full load Current (FLC) Full load current Percent of motor speed (%) Shortcircuit Withstand Rating Standard 208V to 240V - 1ph - 50/60Hz 65,000 A Listings, Approvals and Certifications Enclosure Standard Underwriters Laboratory (UL) New York City Protection Rating Standard: NEMA 2 Optional NEMA 12 NEMA 3 NEMA 3R NEMA 4 Accessories Wall mounting lugs Keylock handle UL218 - Fire pump controllers CSA C22.2 No. 14 Industrial Control Equipment Accepted for use in the City of New York by the Department of Buildings NEMA 4X-304 sst painted NEMA 4X-304 sst brushed finish NEMA 4X-316 sst painted NEMA 4X-316 sst brushed finish Paint Specifications Red RAL3002 Powder coating Glossy textured finish *Please see Disconnecting Means and Locked Rotor Protector details on page 2. 1

8 Submittal Data Sheet Model GPL Electric Pump Controller Limitations Pressure Sensing Surge Suppression Across the line starting only Horsepower rating of maximum 30hp Can only be installed where acceptable by the authority having jurisdiction Not accepted in FM insured property Pressure transducer for fresh water application Pressure sensing connection 1/2 Female NPT Rated for 0-500psi working pressure Internally mounted Surge arrestor rated to suppress surges above line voltage Disconnecting Means & Locked Rotor Protector Circuit breaker (inverse time non ajustable) rated between 150% and 250% of motor full load current Service Entrance Rating Emergency Start Handle Electrical Readings Pressure Readings Pressure and Event Recorder Suitable as service entrance equipment Push and slide to lock Across the line start (direct on line) Voltage phase to phase Amperage of each phase when motor is running Continuous system pressure display Cut-in and Cut-out pressure settings Pressure readings with date stamp Event recording with date stamp Stored in memory for lifetime of controller Data viewable on operator interface display screen Downloadable by USB port to external memory device 2

9 Submittal Data Sheet Model GPL Electric Pump Controller Audible Alarm Visual Indications and Alarms 4 alarm bell - 85 db at 10ft. (3m) Power available Locked rotor Manual start Phase reversal Periodic test Deluge valve start Motor run Fail to start Remote automatic start Pump room alarm Low discharge pressure Remote manual start Motor trouble Low pump room temperature Overcurrent Phase loss Pump room temperature (ºF or ºC) Undercurrent Phase unbalance Pump on demand/automatic start Undervoltage Low water level Emergency start Overvoltage Remote Alarm Contacts ViZiTouch Operator Interface Operation SPDT-8A-250V.AC Power available Phase reversal Motor run Common pump room alarm Overvoltage gh Undervoltage p mp r om Phase unbalance Low pump room temperature High pump room temperature Common motor trouble Overcurrent Fail to start Undercurrent Ground fault Embedded microcomputer with software PLC logic 4.2 color touch screen (HMI technology) Upgradable software Automatic Start Manual Start Stopping Timers Actuation Mode ** Can only be used if approved by the AHJ Expandable storage Multi-language Start on pressure drop Remote start signal from automatic device Start pushbutton Run test pushbutton Deluge valve start Remote start from manual device Manual with Stop pushbutton Automatic after expiration of minimum run timer ** Se Minimum uent al run start timer** (off r ( delay) n Field Adjustable & Visual Countdown Sequential start timer (on delay) Periodic test timer Pressure Non-pressure Visual Indication Automatic Non-automatic 3

10 Submittal Data Sheet Model GPL Electric Pump Controller ViZi Touch Operator Interface ? Power LED 2 - Color touch screen 3 - Alarm LED 4 - HOME page button 5 - ALARM page button 6 - CONFIGURATION page button 7 - HISTORY page button 8 - USB port 9 - START button 10 - Contextual navigation pad 11 - STOP button 12 - RUN TEST button 13 - HELP button 5

11

12

13

14

15

16 Albany Pump Company ltd. cep-860 Series 0-4 gpm/0-150 psi 3/8 npt Utility duty gear pumps The CEP series Utility Gear Pumps are a close tolerance, low flow, high pressure positive displacement pump. A standard in the fire sprinkler industry for excess pressure service. APPLICATIONS Excess Pressure Pump Liquid Transfer/Circulation Small Booster Jockey Pump Spray Nozzles/Misting Hydraulic/Hydrostatic Flow: GPM L/s m 3 /hr Pressure: PSI 10.5 Bar Ft. FEATURES Precision Spur Style Gears Self Priming due to close manufacturing tolerances Suction lift of up to 20 feet Pump housings are of bronze Pump shafts are of stainless steel Lip seals of Buna or Viton Carbon graphite shaft bearings Bearings never need lubrication Easy maintenance and service SPECIFICATIONS PORTS CAPACITY PRESSURE INLET PRESSURE TEMPERATURE 3/8 NPT / mm 4.6 USGPM / 0.29 L/s (Max.) 150 PSI / 10.5 Bar (Max.) 50 PSI / 3.5 Bar (Max.) 225 F (100 C) (Buna Seal) Performance GPM Performance Curve - CEP 860 Capacity 1750 RPM HP RPM PSI H P ROTATION Precision Spur Style Gears Self Priming due to close manufacturing tolerances Suction lift of up to 20 feet Pump housings are of bronze Maintenance To ensure a long life to this pump a strainer is always recommended in front of the pump inlet. DIMENSIONS /2 HP /8" NPT Phone: (888) Fax: (888) Web: sales@albanypump.com

17

18

19

20 For Commercial, Institutional and Industrial Applications ES-530C Job Name Contractor Job Location Approval Engineer Contractor s P.O. No. Approval Representative Series 530C Calibrated Pressure Relief Valves Sizes: 1 2" or 3 4" (15 or 20mm) Series 530C Calibrated Pressure Relief Valves are spring operated brass valves designed for use only as protection from the build up of excessive pressure in systems containing water, oil or air. Series 530C valves incorporate a calibrated adjustment feature for setting the valve to the relief pressure required. These valves are ideally suited for bypass thermal expansion relief. Features Calibrated adjustment feature for setting valve to relief pressure required Adjustable range psi ( bar) All brass construction All stainless steel spring Buna-N disc on machined body seat Inlet (bottom), male NPT threaded Outlet (side), female NPT threaded Pressure Temperature Maximum Temperature: 180 F (82 C) Spring Ranges 1 2" or 3 4" (15 or 20mm): psi ( bar) 3 4" (20mm): psi ( bar) Application Note: The Watts Series 530C are not ASME approved safety relief valves and should not be used in system application with this requirement. MODEL SIZE (DN) DIMENSIONS WEIGHT Height Width in. mm in. mm in. mm lbs. kg. 530C 1 2 or or Materials Inlet Pressure Capacity (530C) psi bars X = Set Point Flow Model 530C 1. Body Brass 2. Bonnet Brass 3. Disc Holder Brass 4. Disc Buna-N (Nitrile) 5. Adjustable Spring Stainless Steel 6. O-ring Buna-N (Nitrile) 7. Spring Washer Brass 3 4" (20mm) 1 2" (15mm) gpm lpm Watts product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements, please contact Watts Technical Service. Watts reserves the right to change or modify product design, construction, specifications, or materials without prior notice and without incurring any obligation to make such changes and modifications on Watts products previously or subsequently sold. USA: 815 Chestnut St., No. Andover, MA ; Canada: 5435 North Service Rd., Burlington, ONT. L7L 5H7; Water Safety & Flow Control Products ES-530C 0630 Watts Regulator Company, 2006

21 MUELLER O.S.&Y. Resilient Wedge Gate Valve q R : O.S.&Y. RESILIENT WEDGE GATE VALVE WITH FLANGE ENDS 2-1/2", 3", 4", 6", 8", 10" and 12" SIZES MEETS OR EXCEEDS ALL APPLICABLE REQUIREMENTS OF UL 262 AND FM 120/1130 SPECIFICATIONS AND COMPLIES WITH NSF-61 IRON BODY WITH MUELLER PRO-GARD FUSION EPOXY COATED INTERIOR & EXTERIOR SURFACES OUTSIDE SCREW AND YOKE (O.S.&Y.) FLANGED END DIMENSIONS AND DRILLING Options Stainless steel fasteners: Type 304 or 316 ASTM B98-C66100/H02 STEM PARTS LIST Catalog Part No. Description Material Material Standard G-1 Cap Nut Bronze ASTM B62 G-3 Hand Wheel Cast Iron ASTM A126 CL B G-4 Washer Brass G-5 Bush Nut Bronze ASTM B584 G-7 Gland Nut Bronze ASTM B21 Alloy 464 G-8 Packing Gland Ductile Iron ASTM A536 Grade G-10 Gland Bolt Stainless Steel Type 304 G-11 Yoke Bolt & Nut Stainless Steel Type 304 G-16 Bonnet Bolts & Nuts Stainless Steel Type 304 G-23 Stem Packing Lubricated Flax G-206 Guide Cap Bearings Celcon G-209 Wedge, Rubber Encapsulated Cast Iron** ASTM A126 CL B G-211 Bonnet Gasket Rubber ASTM D2000 G-212 Body Cast Iron ASTM A126 CL B G-213 Stem Bronze ASTM B138 G-214 Bonnet & Yoke w/bushing Cast Iron ASTM A126 CL B G-215 Bonnet Cast Iron ASTM A126 CL B G-216 Yoke Cast Iron ASTM A126 CL B G-217 O-ring Nitrile ASTM D2000 G-218 Disc Nut Bronze ASTM B62 G-219 Stem Nut Pin Stainless Steel Type 304 DIMENSIONS Size Dimension* 2-1/2" 3" 4" 6" 8" 10" 12" A 19.50" 19.25" 23.68" 31.38" 38.50" 47.00" 53.50" AA 15.75" 15.50" 19.00" 24.50" 29.50" 35.75" 40.50" E 7.00" 7.00" 10.00" 12.00" 14.00" 16.00" 16.00" R 7.00" 7.50" 9.00" 11.00" 13.50" 16.00" 19.00" FF 7.50" 8.00" 9.00" 10.50" 11.50" 13.00" 14.00" UU 5.50" 6.00" 7.50" 9.50" 11.75" 14.25" 17.00" FFF (number and size of holes) " " " " " 12--1" 12--1" Turns to open Weight (lbs.)* RUBBER ENCAPSULATED IRON WEDGE ADJUSTABLE PACKING HANDWHEEL OPEN LEFT OR OPEN RIGHT 200 PSIG (1379KPA) MAXIMUM WORKING PRESSURE 400 PSIG (2758 KPA) STATIC TEST EPOXY COATING MEETS OR EXCEEDS ANSI/AWWA C550 AND COMPLIES WITH NSF-61 See page B-1-22 for ordering insturctions. *All dimensions are in inches. All weights are in pounds and are approximate. ** Fully encapsulated in molded rubber with no iron exposed. 2-1/2" - 6" sizes have a one-piece bonnet & yoke. 8" - 12" sizes have a two-piece bonnet & yoke. FF Project: Address: Contractor: Engineer: Submittal Date: Notes 1: Notes 2: Mueller UL/FM PROJECT INFORMATION APPROVAL STAMP q Approved q Approved as noted q Not approved Remarks:

22 IPS CARBON STEEL PIPE FIRE PROTECTION VALVES FireLock Butterfly Valve SERIES 705W WITH WEATHERPROOF ACTUATOR MEA: E CSFM: :113 The Series 705W butterfly valve features an approved weatherproof actuator housing approved for indoor or outdoor use. It has a ductile iron body and disc with EPDM disc coating. The body is coated with a heat fused polyphenylene sulfide blend to meet FM requirements. Designed for fire protection services only. Series 705W valve is UL Listed and FM Approved for 300 psi/2065 kpa service. Contact Victaulic for details of agency approvals. WEATHERPROOF ACTUATOR Supervisory switches that monitor the valve in the fully open position for valves are available 2 1/2 12"/ mm pre-wired (PW). OPTIONAL SUPPLY-SIDE TAP Series 705W valves are available with a 1/2" NPT supply side tap designed to allow direct water supply connection to Victaulic FireLock actuated fire protection valves. See separate drawings below. This is an optional feature and must be clearly noted on all orders. MATERIAL SPECIFICATIONS Body: Ductile iron conforming to ASTM A-536, coated with polyphenylene sulfide blend. Disc: Ductile iron conforming to ASTM A-536, various grades, EPDM coated. Disc Coating: Grade E EPDM EPDM (Green color code). Temperature range 30 F to +230 F/ 34 C to +110 C. Recommended for cold and hot water service within the specified temperature range plus a variety of dilute acids, oil-free air and many chemical services. UL classified in accordance with ANSI/NSF 61 for cold +86 F/+30 C and hot +180 F/+82 C potable water service. NOT RECOMMENDED FOR PETROLEUM SERVICES. Stem Bearings: Teflon impregnated fiberglass with stainless steel backing. Stem Bearing Nuts: Type 416 Stainless Steel. Tap Plug: Carbon steel, plated. O-Ring: EPDM Bracket: Carbon steel, painted. Actuator: 21/2 8"/ mm: Bronze traveling nut on a steel lead screw, in a ductile iron housing "/ mm: Steel worm and cast iron quadrant gear, in a cast iron housing. JOB/OWNER CONTRACTOR ENGINEER System No. Submitted By Spec Sect Para Location Date Approved Date VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA. REV_G 10.18_1

23 IPS CARBON STEEL PIPE FIRE PROTECTION VALVES FireLock Butterfly Valve SERIES 705W WITH WEATHERPROOF ACTUATOR DIMENSIONS Nominal Size inches mm Size Actual Outside Diameter inches mm End to End A Dimensions inches/millimeters Aprx. Wgt. Each Hgt. B E F J O N P lbs/kg * / * mm * * * * mm mm * * * On Centerline These dimensions apply only to a Series 705W Butterfly Valve with a 1/2-inch NPT, supply-side tap 1. To prevent rotation of valves. it is recommended that Series 705W be installed with Victaulic Style 07 Zero-Flex, Style 005 FireLock, Style 009/009V FireLock EZ, or Style HP-70 Rigid Couplings. If Victaulic flexible couplings are used. additional support may be required. 2. Valve must not be installed with disc in full open position. Disc must be partly closed so that no part is protruding beyond end of valve body. 3. Victaulic grooved end butterfly valves are permitted for use with grooved end pipe (IPS) only. Not permitted for use with plain end (IPS) pipe. 4. Series 705W valves are designed for ambient weather conditions as opposed to submersible service. O O B ½" NPT Supply Tap B ½" NPT Supply Tap N N F J F A E P J A E P 2 1/2 4-INCH/ MM SIZES 5 12-INCH/ MM SIZES VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA. REV_G 10.18_3

24 IPS CARBON STEEL PIPE - FIRE PROTECTION VALVES FireLock Check Valves SERIES SEE VICTAULIC PUBLICATION FOR DETAILS Series 717 FireLock check valve is a CAD-developed design that is hydrodynamically efficient. A totally rubber encapsulated disc on 4 12"/ mm sizes provides superior corrosion resistance. This single disc design incorporates a spring assisted feature for non-slamming operation. For systems requiring a Riser Check option refer to section The 4"/100 mm and larger sizes are provided with upstream and downstream drains and a welded-in nickel seat design. All sizes of Series 717 can be installed in the vertical or horizontal position to provide leak-free sealing under conditions as low as five feet of head. Each valve is factory tested to 500 psi/3440 kpa. The 2 1/2 and 3"/65 and 80 mm sizes are UL/ ULC Listed and 4"/100 mm sizes and larger are UL/ULC Listed and FM Approved for services up to 250 psi/1725 kpa. Sizes 4 8"/ mm (except mm size) are VdS approved. Grooved ends allow fast, easy installation with just two Victaulic couplings or the valve may be mounted to flanged (ANSI CL.150) equipment using either to Victaulic Style 741 Vic-Flange or Style 744 FireLock flange adapters on either end. DIMENSIONS A TYPICAL 2 1/2 3 /65 80 MM P R B A 3 K 2 B J ½" NPT Upstream Drain ½" NPT Downstream Drain 2" NPT (Drain Optional) K B TYPICAL 4 8 / MM P 1 ½" NPT Upstream Drain 2 ½" NPT Downstream Drain A 2 1 J C C D E 1 C D E Nominal Size Inches mm Size Actual Outside Diameter Inches mm Dimensions- Inches/millimeters E to E A B C D E J K P R Approx. Wgt. Ea. 2 1/ mm mm mm VdS Approved Lbs. kg TYPICAL / MM JOB/OWNER CONTRACTOR ENGINEER System No. Submitted By Spec Sect Para Location Date Approved Date VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA. REV_H 10.08_1

25 IPS CARBON STEEL PIPE - FIRE PROTECTION VALVES FireLock Check Valves SERIES 717 MATERIAL SPECIFICATIONS Body: Ductile iron conforming to ASTM A-536, grade Ductile iron conforming to ASTM A 395, grade , is available upon special request. 2 1/2 3"/65 80 mm sizes PPS coated. 4 12"/ mm sizes painted black enamel. Body Seat: 21/2 3"/65 80 mm sizes PPS coated. 4 12"/ mm integrally welded on nickel alloy. Disc Seal or Coating: Grade E EPDM EPDM (Green color code). Temperature range 30 F to +230 F/ 34 C to +110 C. Recommended for cold and hot water service within the specified temperature range plus a variety of dilute acids, oil-free air and many chemical services. UL classified in accordance with ANSI/NSF 61 for cold +86 F/+30 C and hot +180 F/+82 C potable water service. NOT RECOMMENDED FOR PETROLEUM SERVICES. * Services listed are General Service Recommendations only. It should be noted that there are services for which these gaskets are not recommended. Reference should always be made to the latest Victaulic Gasket Selection Guide for specific gasket service recommendations and for a listing of services which are not recommended. Discs: 2 1/2 3"/65 80 mm Aluminum bronze conforming to ASTM B-148 with Grade E Seal. 4 12"/ mm ductile iron conforming to ASTM A-536, grade , fully encapsulated in Grade E elastomer. Shaft: 2 1/2 3"/65 80 mm Type 416 stainless steel. 4 12"/ mm Type 316 stainless steel. Spring: All sizes Type 302/304 stainless steel. Shaft Plug: 2 1/2 3"/65 80 mm only; SAE Hex Socket Type conforming to ASTM A-576, cadmium plated to military specifications QQ-P-416A, class 3 type "/ mm only; carbon steel zinc plated to ASTM B-633. Pipe Plug: 4 12"/ mm only; carbon steel zinc plated to ASTM B VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA _2 REV_H

26