Resource Center. 30.5mm pilot devices. Answers for industry.

Transcription

1 Resource Center 30.5mm pilot devices Answers for industry.

2 Siemens 30.5mm Pilot Device Resource Center Table of Contents General Information 1 Technical Specifications 2 Pushbuttons 3 Non-Illuminated Illuminated Selector Switches; 4-Position/Specialty 15 Non-Illuminated Specialty Pilot Lights 5 Plastic Glass Push-Pull Operators; 2-Position Maintained 17, 19 Non-Illuminated, Illuminated Twist to Release 7 Non-Illuminated Illuminated Push-Pull Units; 3-Position Momentary 17, 21 Non-Illuminated, Illuminated Selector Switches; 2-Position 9 Non-Illuminated Illuminated Keyed Push-Pull Units; 3-Position Push-Maintained, Pull Momentary 23, 25 Non-Illuminated Illuminated Selector Switches; 3-Position 11, 13 Non-Illuminated Illuminated Keyed Accessories 27 Cam and Contact Block Selection 28

3 Siemens 30.5mm Pilot Devices General Information Features n Octagonal Mounting Nuts n Meets Type 1, 3, 3R, 4, 4X, 12, 13 and Automotive Standards n Heavy Duty Rated NEMA A600/P600 Contacts n Positive Indexing Selectors n Bifurcated Movable Contacts n Attractive Chrome Plating or Black Matte Finish n Boots Not Required for Type 4 n UL Listed File # E22655 n CSA Certified File # LR6535 n Touchsafe Terminals Application Siemens pilot devices and accessories are designed to provide long, trouble free service in the most demanding of industrial applications. These controls are water, oil, and dust tight and meet NEMA Type 1, 3, 3R, 4, 4X, 12, and 13 specifications. Rugged Industrial control operators are of durable one piece castings. Heavy duty plastic buttons resist oils and corrosion. Silver contacts carry heavy duty ratings while standard gold flashing on contacts allows for use in low current applications. Flexible Accessories modify standard pushbuttons, selector switches, and pilot lights. Building block construction of contact blocks makes it possible for many circuitry combinations. Industrial Appearance Pilot controls add luster to panels. Chrome plating covers exposed metal parts. The black matte finish of Black Max pilot device operators allows for an alternative look to finished panels while still offering corrosion resistance and superior ingress protection. Pushbutton Operators The pushbutton operator base consists of a durable, one piece casting. The base is equipped with a heavy duty actuator with a stainless steel spring, a neoprene actuator sealing ring to prevent water, oil, and dust from penetrating to the contact blocks, a neoprene gasket to seal operator mounting hole, and a chrome plated locknut. Mushroom Head Pushbutton Operators Operator base construction is identical to the pushbutton operator base. The actuator is molded of high impact material for either a 1⁵ ₈ inch or 2 ¹ ₂ inch diameter molded head. Contact Blocks Contact blocks have double-break bifurcated silver contacts, with gold flashing as standard, which improves contact fidelity. Contact blocks are heavy duty rated NEMA A600/P600 and suitable for applications down to 5V/1MA solid state outputs. Molded bodies and pushers resist arcing and tracking. All units have stainless steel springs that resist corrosion and provide strong contact pressure. Captive mounting screws speed panel assembly. Push-Pull Operators Push-pull operators combine two or three functions in one unit. The maintained operator has two positions, typically pull to start, push to stop. The momentary operator with three positions provides spring return from both pull and push positions. A three-position operator with push maintained and pull momentary is available. Push-pull operators are available in illuminated or non-illuminated versions. Two-button Maintained Operator Two-button maintained operator pushbuttons consist of two Pushbuttons and a latching assembly. When actuated the button remains depressed and is freed only by the release operator to which it is linked. The button assembly adjusts for mounting from a 1¹³ ₁₆ inch to a 2 ⁵ ₈ inch center. Transformer Type Pilot Lights Transformer type pilot lights are available with a 120, 240, 277, 480, or 600 Volt primary (50/60 Hertz) and a separate secondary winding which supplies reduced voltage to a miniature bayonet base 6 Volt lamp. These units are suitable for applications where vibration is present and long bulb life is desirable. Full Voltage Type Pilot Lights Full voltage pilot lights are available for 6, 12, 24, 120, 277V, and 240 Volt AC and DC applications. The 240 volt pilot light is supplied with a 120 volt lamp and a voltage dropping resistor. LED Type Pilot Lights and LED Module The integrated LED modules are a single unit combining all the features of a LED bulb and lighting module into one. These will have extended life and are the most resistant to vibration. LEDs (light emitting diodes) can be used in pilot lights instead of incandescent bulbs because of their extremely long life, resistance to vibration, and ambient sensitivity. Selector Operators Selector operators have positive action indexing. Operators are available with either a short or long lever. The molded black lever is designed to accept a color insert. A white insert is provided as standard; however, eight alternative lever insert colors are available. Each operator is equipped with a cam to actuate plungers of contact blocks assembled behind the operator. Two, three, and four position operators are available with seven different cams. 1

4 Siemens 30.5mm Pilot Devices Technical Specifications Standards UL Listed File # E22655 CSA Certified File # LR6535 Utilization Category NEMA A600/P600 Degree of Protection 52B, 52P-, 52S-, 52M- Operators NEMA: 1, 3, 3R, 4, 4X, 12 and 13 IEC 529; IP10, IP11, IP14, IP52, IP54, and IP56 Rated Operational Current NEMA A Continuous Amps Voltage AC Make Amps Break Amps 120V V V V Total VA NEMA P600 - Rating Codes for DC Control Circuit Application Thermal Continuous Test Current Amps 5.0 Maximum Make or Break; Current / Amps 125V V V 0.20 Maximum Make or Break Volt amperes at 300V or Less 138 Contact Blocks 52BAK, -BAJ, -BAH, -BAU, -BJK 600VAC Maximum, Heavy Duty 52BAR 200VAC.25 Amp, 10 Watt Maximum 200VDC.50 Amp, 10 Watt Maximum Contact blocks are suitable for applications down to 5V/1MA low voltage applications as found in PLCs. 52BAR are Class 1; Division 2 Compliant Pilot Light Full Voltage 52PL4 -B (6-8V), -C (12V), -D (24V), -E (120V) 120V AC/DC Maximum LED Module 52PL5 -L (24V), -M (120V) -N (240V) 240V AC Maximum Transformer Type 52BL452BL5 -G (120V), -H (240V), -J (480V), K (600V) 600V AC Maximum, 50/60 Hz Push-to-Test Full Voltage 52PT6 -B (6-8V), -C (12V), -D (24V), -E (120V) 24V AC/DC Maximum LED Module 52BP6 -L (24V), -M (120V), -N (240V) 240V AC Maximum Transformer -G (120V), -H (240V), -J (480V), -K (600V) 600VAC Maximum, 50/60 Hz Illuminated Push-Pull Full Voltage LED Module 52PP2(3,7) -B (6-8V), -C (12V), -D (24V), -E (120V) 24V AC/DC Maximum -L (24V), -M (120V), - N (240V) 240V AC Maximum Transformer 52BP2(3,7) -G (120V), -H (240V), -J (480V), -K (600V) 600VAC Maximum, 50/60 Hz Illuminated Selector Full Voltage 52SA7 -AD,-BD,-CD 24V AC/DC Maximum Switch Transformer 52SA7 -AG, (120V), -BG (120V), -CG (120V), 240VAC Maximum, 50/60 Hz -BH (240V), -CH (240V) Dielectric Strength 2200V for one minute Mechanical Design Life Cycles Vibration Frequency 5-60Hz.; Disp..030 inches, sweep 5 minutes for a duration of 30 minutes on each axis. Not to exceed 5.5 G s for maximum of 1 minute. Pushbuttons Momentary, Non-illuminated 5,000,000 Operating Cycles Momentary, Illuminated 300,000 Operating Cycles Push-Pull Maintained 300,000 Operating Cycles Momentary 2,000,000 Operating Cycles Twist-to-Release 300,000 Operating Cycles Selector Non-illuminated 2,000,000 Operating Cycles Switches Illuminated, Key-operated 2,000,000 Operating Cycles Contact Operation Standard Contact Black Logic Reed Wire Gauge #18-12 AWG Terminal Screw Torque 2-10 lb-in / 20 lb-in max; 8 lb-in recommended Locknut Torque 15 ft. lbs. max Temperature Operating 31F to +158F (-35C to +70C) Range Storage 40F to +185F (-40C to +85C) All parts are designed and manufactured of corrosion resistant material or are plated or painted as corrosion protection. All contact block contacts are gold flashed as a standard offering. Internal return spring mechanisms of operators and contact blocks of stainless steel. RoHS Compliant. Declaration of Conformity The products listed below, to which this declaration relates, are in conformity with the following standards, following the provisions of the Low Voltage Directive (LVD) (73/23/EEC), and the Electromagnetic Compatibility Directive (89/336/EEC.) Products: Contact Blocks: Cat Nos. 52BAE, 52BAH, 52BAJ, 52BAK, 52BAR, 52BAU and 52BJK, with suffixes. Pilot Lights: Cat Nos 52P, with suffixes. Operators: Cat Nos 52S or 52P, with suffixes. Applicable Standards: EN Low-Voltage Switchgear and controlgear. Enclosed devices meet the requirements of environmental ratings of IP10, IP11, IP14, IP52, IP54, and IP56. Open devices, when mounted as instructed, in environmental type IP10, IP11, IP14, IP52, IP54 or IP56 enclosures, maintain the environmental requirements for those enclosure types. 2

5 Siemens Pushbuttons Components Operator Specific Complete Units Operators Only Contact Blocks Accessories Flush Pushbuttons Non-Illuminated 52P*8*6* Chrome A A 1) K 1 NO BlackMax X F 2) J 1 NC A 1 NO + 1NC F 2 NO 1) Flush G 2 NC 2) Extended B 2 NO + 2 NC Flush Pushbuttons Non-Illuminated 52P*8*6 Kit All Colors 52P*8*N Chrome A A Flush Black Max X F Extended Contact Blocks For All Operators 52BAK 1 NO 52BAJ 1 NC 52BJK 1 NO + 1 NC 52BAH 1 NO Early Make 52BAE 1 NC Late Break 52BAU 1 NC Extra Late Break 52BAR 1 NO + 1 NC 2) 1) 52BAR 2) Hermetically Sealed, UL Listed for Class 1, Division 2,.25A Max., 200V AC, 10 Watt.5A Max., 200V AC, 10 Watt 1) Basic Pushbuttons For Basic Non-Illuminated Pushbuttons 52RA1*1 52RA1*2 52RA1*3 52RA1*4 52RA1*5 52RA1*6 52RA1*8 Kit All Colors 52RA1*N A Flush F Extended Extended Mushroom Head Momentary Pushbuttons Non-Illuminated 52P*9*1* 52P*9*2* 52P*9*3* 52P*9*4* 52P*9*5* 52P*9*6* 52P*9*8* Chrome B D 1) K 1 NO Black Max X E 2) J 1 NC A 1 NO + 1NC 1) 1⁵ ₈ Head F 2 NO 2) 2¹ ₂ Head G 2 NC B 2 NO + 2 NC Extended Mushroom Head Momentary Pushbuttons Non-Illuminated 52P*9*6 Kit All Colors 52P*9*N Chrome B D 1⁵ ₈ Head Black Max X E 2¹ ₂ Head Contact Blocks For All Operators 52BAK 1 NO 52BAJ 1 NC 52BJK 1 NO + 1 NC 52BAH 1 NO Early Make 52BAE 1 NC Late Break 52BAU 1 NC Extra Late Break 52BAR 1 NO + 1 NC 2) 1) 52BAR 2) Hermetically Sealed, UL Listed for Class 1, Division 2,.25A Max., 200V AC, 10 Watt.5A Max., 200V AC, 10 Watt 1) Mushroom Head Buttons For Extended Momentery Pushbuttons 52RB3*1 52RB3*2 52RB3*3 52RB3*4 52RB3*5 52RB3*6 52RB3*8 Kit All Colors 52RB3*N D 1⁵ ₈ Head E 2¹ ₂ Head 1) Illuminated Pushbuttons/Push-to-Test 52*T6*2A 1 NO + 1 NC 52*T6*3A 1 NO + 1 NC 52*T6*5A 1 NO + 1 NC 52*T6*9A 1 NO + 1 NC CL 52*T6*AA 1 NO + 1 NC WH 52*T6*BA 1 NO + 1 NC Less Lens 52*T6*NA 1 NO + 1 NC 1) Chrome P B 6-8V Full Voltage 2) BlackMax B D 24V Full Voltage 2) G 120V Transformer Type 2) 3) H 240V Transformer Type 2) 3) J 480V Transformer Type 2) 3) K 600V Transformer Type 2) 3) L 24V LED Module M 120V LED Module N 240V LED Module 1) Not available for LED. 2) For LED, add B to the end of the assembled number. 3) With 6V lamp. Contact Blocks For All Operators 52BAK 1 NO 52BAJ 1 NC 52BJK 1 NO + 1 NC 52BAH 1 NO Early Make 52BAE 1 NC Late Break 52BAU 1 NC Extra Late Break 52BAR 1 NO + 1 NC 2) 1) 52BAR 2) Hermetically Sealed, UL Listed for Class 1, Division 2,.25A Max., 200V AC, 10 Watt.5A Max., 200V AC, 10 Watt Illuminated Pushbutton Lenses For Illuminated Pushbuttons/Push-to-test 52RA5P2 CLR WH 52RA5P3 52RA5P5 52RA5P9 52RA5PA 52RA5PB 3

6 A B Pushbutton and Mushroom Head Momentary Non-Illuminated Cat. No. 52PA8, 52PX8, 52PB9, 52PX9 Installation Instructions Units are assembled as shown. 1. Assemble oil rings. 2. Mount unit on panel as shown in illustration. 3. Position trim ring or legend plate (trim ring is discarded when legend plate is used). 1) 4. Position index locking ring on unit as shown in illustration. 5. Assemble and tighten lock nut. 6. Position and press on color cap. Push-to-Test Illuminated Pushbutton Cat. No. 52PT6, 52BT6 Installation Instructions 1. Remove lock nut from operator. Mount operator base panel as shown and tighten to 15 ft. lbs. 2) 2. Place lens gasket around lamp, sealing it firmly in a groove provided. 3. Screw lens into threaded socket of operator base and tighten by hand. Installing Guard Accessory (52AAGL) 1. To install guard accessory, replace operator lock nut with lock nut from guard accessory kit. 2. Screw guard on the operator. NOTE: The guard is designed to protect the push button from accidental operation. 1) Second oil ring and trim ring not used on Black Max 4X devices. 2) Spacers and trim ring not used on black 4X devices. Notes for BlackMax 4X devices: The trim ring is not needed or supplied. Only use the index locking ring when using a metal nameplate. Discard when not using a name plate or when using a plastic nameplate. Use locknut wrench, 52MAWB. IMPORTANT THESE INSTRUCTIONS DO NOT PURPORT TO COVER ALL DETAILS OR VARIATIONS IN EQUIPMENT, NOR TO PROVIDE FOR EVERY POSSIBLE CONTINGENCY TO BE MET IN CONNECTION WITH INSTALLATION, OPERATION OR MAINTENANCE. SHOULD FURTHER INFORMATION BE DESIRED OR SHOULD PARTICULAR PROBLEMS ARISE WHICH ARE NOT COVERED SUFFICIENTLY FOR THE PURCHASER S PURPOSES, THE MATTER SHOULD BE REFERRED TO THE LOCAL SIEMENS SALES OFFICE. THE CONTENTS OF THIS INSTRUCTION MANUAL SHALL NOT BECOME PART OF OR MODIFY ANY PRIOR OR EXISTING AGREEMENT COMMITMENT OR RELATIONSHIP. THE SALES CONTRACT CONTAINS THE ENTIRE OBLIGATION OF SIEMENS. THE WARRANTY CONTAINED IN THE CONTRACT BETWEEN THE PARTIES IS THE SOLE WARRANTY OF SIEMENS. ANY STATEMENTS CONTAINED HEREIN DO NOT CREATE NEW WARRANTIES OR MODIFY THE EXISTING WARRANTY. A 2 1/8 1 5/8 1 5/ /8 4 3/8 This Side Up Oil Rings Color Cap 1/16-1/4 1 1/4 2 1/4 1 1/4 2 1/ Typical spacing shown. Automotive legend requires 2¹ ₂ spacing. Some accessories also require additional spacing. B Typical spacing shown. Automotive legend requires 2¹ ₂ spacing. Some accessories also require additional spacing..190 Panel Legend plate or Trim ring Index Locking Ring A Non-illuminated momentary push button flush extended B Push to test illuminated push button B styles with one contact block Legend Plates 2.25 (57) 1.52 (39) 1.09 (28) 1.05 (27) 1.74 (44) 1 5/8 Large Jumbo Automotive 2.74 (70) 2 1/ /8 1 5/8 Shaft Oil Rings 2 1/4 1/16-1/4 1 1/ /4 Panel Trim ring or Legend plate Index Locking Ring Lock Nut Lock Nut *Mushroom Head Momentary Operator Mounting. For Operator Dimensional Drawings See Page 1-6. Set Screw 3/32 Wrench Volts Lamps 6-8* # #1829 Wiring Instructions (Typical Motor Controller Application) Push-Pull Head 4 Hazardous voltage. Can cause death, serious personal injury, or property damage. To avoid electrical shock, turn off electrical power to controls before performing installation maintenance.

7 Siemens Pilot Lights Components Operator Specific Complete Units Operators Only Lighting Modules Accessories Pilot Lights Plastic Lens 52*L4*9 CL 52*L4*A WH 52*L4*B Less Lens 52*L4*N 1) Chrome P B 6V Full Voltage 2) BlackMax B C 12V Full Voltage 1) 2) D 24V Full Voltage 2) E 120V Full Voltage 2) G 120V Transformer 2) 3) H 240V Transformer 2) 3) J 480V Transformer 2) 3) K 600V Transformer 2) 3) L 24V LED Module 4) M 120V LED Module 4) N 240V LED Module 4) Pilot Lights Glass Lens 52*L5*9 CL 52*L5*A WH 52*L5*B Less Lens 52*L5*N 1) Chrome P B 6V Full Voltage 2) BlackMax B C 12V Full Voltage 1) 2) D 24V Full Voltage 2) E 120V Full Voltage 2) G 120V Transformer 2) 3) H 240V Transformer 2) 3) K 600V Transformer 2) 3) L 24V LED Module 4) M 120V LED Module 4) N 240V LED Module 4) Pilot Lights without Lighting Module Plastic Lens 52*L4X2 52*L4X3 52*L4X5 52*L4X9 CL 52*L4XA WH 52*L4XB Less Lens 52*L4XN Chrome P BlackMax B Pilot Lights without Lighting Module Glass Lens 52*L5X2 52*L5X3 52*L5X5 52*L5X9 CL 52*L5XA WH 52*L5XB Less Lens 52*L5XN Chrome P BlackMax B Lighting Modules Full Voltage WHT/CLR Incandascent 2) Transformer WHT/CLR Incandascent 2) LED Module WHT/CLR 52AAF*2B 1) 52AAF*3B 1) 52AAF*5B 1) 52AAF*9B 52AAF*BB 52AAF*B B 6V D 24V E 120V 52AAT*2B 1) 52AAT*3B 1) 52AAT*4B 1) 52AAT*5B 52AAT*BB 52AAT*B G 120V H 240V J 480V K 600V 52AAI*2 52AAI*3 52AAI*4 52AAI*5 52AAI*B L 24V M 120V N 240V 1) For cluster LED, replace the last digit B with a Y. 2) All colors can be used with incandescent bulb. Pilot Light Lenses 52RA4*2 52RA4*3 52RA4*5 52RA4*9 CLR 52RA4*A WHT 52RA4*B S Plastic T Glass 1) Not available for LED. 2) For single LED, add XB to end of assembled number. For cluster LED, add XY to end of assembled number. 3) With 6V lamp. 4) Integrated LED module utilizes a single LED. 5

8 Pilot Light Cat. Nos. 52PL, 52BL Installation Ins tructions Units are assembled as shown. 1. Assemble oil rings. 2. Mount unit on panel as shown in illustration. 2a. When installing a pilot light in a NEMA 4 plastic or non-corrosive enclosure, a grounding ring and two oil rings must be installed. See Fig. 1A for placement. (Order kit #52AL which includes 1 ground ring and 1 oil ring). 3. Position trim ring or legend plate (trim ring is discarded when legend plate is used). 1) 4. Position index locking ring on unit as shown in illustration. 5. Assemble and tighten lock nut to 15 ft. lbs. 1) Trim ring not used on black 4X devices. Notes for BlackMax 4X devices: The trim ring is not needed or supplied. Only use the index locking ring when using a metal nameplate. Discard when not using a name plate or when using a plastic nameplate. Use locknut wrench, 52MAWB. IMPORTANT THESE INSTRUCTIONS DO NOT PURPORT TO COVER ALL DETAILS OR VARIATIONS IN EQUIPMENT, NOR TO PROVIDE FOR EVERY POSSIBLE CONTINGENCY TO BE MET IN CONNECTION WITH INSTALLATION, OPERATION OR MAINTENANCE. SHOULD FURTHER INFORMATION BE DESIRED OR SHOULD PARTICULAR PROBLEMS ARISE WHICH ARE NOT COVERED SUFFICIENTLY FOR THE PURCHASER S PURPOSES, THE MATTER SHOULD BE REFERRED TO THE LOCAL SIEMENS SALES OFFICE. Typical spacing shown. Automotive legend requires 2¹ ₂ spacing. Pilot light, plastic lens, transformer or full voltage, lighting module 1.24 (31) 1.70 (43) (49) 1.09 (28) Pilot light, plastic lens, integral LED, lighting module 1.24 (31) 1.70 (43) (47) 1.00 (25) THE CONTENTS OF THIS INSTRUCTION MANUAL SHALL NOT BECOME PART OF OR MODIFY ANY PRIOR OR EXISTING AGREEMENT COMMITMENT OR RELATIONSHIP. THE SALES CONTRACT CONTAINS THE ENTIRE OBLIGATION OF SIEMENS. THE WARRANTY CONTAINED IN THE CONTRACT BETWEEN THE PARTIES IS THE SOLE WARRANTY OF SIEMENS. ANY STATEMENTS CONTAINED HEREIN DO NOT CREATE NEW WARRANTIES OR MODIFY THE EXISTING WARRANTY (89) 1.70 (43) 3.31 (84) 1.70 (43) Legend Plates Hazardous voltage. Can cause death, serious personal injury, or property damage. To avoid electrical shock, turn off electrical power to controls before performing installation maintenance. Pilot light, glass lens, integral LED, lighting module 1.42 (36) 3.50 (89) 1.70 (43) (47) 1.00 (25) Pilot light, glass lens, transformer or full voltage, lighting module 3.68 (93) 1.42 (36) 1.70 (43) 1.94 (47) 1.09 (28) 1.70 (43) 1.63 (41) Large Jumbo Automotive 6

9 Siemens Twist-to-Release Units Components Operator Specific Complete Units Operators Only Contact Blocks Accessories 1) Twist-to-Release Non-Illuminated Chrome BlackMax 52*R8W2A 52*R8W3A 52*R8W5A P B 1 NO + 1 NC 1 NO + 1 NC 1 NO + 1 NC Twist-to-Release Non-Illuminated Chrome BlackMax 52*R8W2 52*R8W3 52*R8W5 P B Contact Blocks For All Operators 52BAK 1 NO 52BAJ 1 NC 52BJK 1 NO + 1 NC 52BAH 1 NO Early Make 52BAE 1 NC Late Break 52BAU 1 NC Extra Late Break 52BAR 1 NO + 1 NC 1) 1) Hermetically Sealed, UL Listed for Class 1, Division 2,.25A Max., 150V AC, 10 Watt.5A Max., 150V AC, 10 Watt 1 3/4 Mushroom Head Plastic For Non-Illuminated Twist-to-Release 52RC3R2 52RC3R3 52RC3R5 1) Twist-to-Release Illuminated 52*R8*RA 1 NO + 1 NC 52*R8*SA 1 NO + 1 NC 52*R8*TA 1 NO + 1 NC Chrome P B 6V Full Voltage 2) BlackMax B C 12V Full Voltage 1) 2) D 24V Full Voltage 2) E 120V Full Voltage 2) G 120V Transformer Type 2) 3) H 240V Transformer Type 2) 3) J 480V Transformer Type 2) 3) K 600V Transformer Type 2) 3) L 24V LED Module 4) M 120V LED Module 4) N 240V LED Module 4) Twist-to-Release Illuminated 52*R8*R 52*R8*S 52*R8*T Chrome P B 6V Full Voltage 4) BlackMax B C 12V Full Voltage 1) 4) D 24V Full Voltage 4) E 120V Full Voltage 4) G 120V Transformer Type 4) 2) H 240V Transformer Type 4) 2) J 480V Transformer Type 4) 2) K 600V Transformer Type 4) 2) L 24V LED Module 3) M 120V LED Module 3) N 240V LED Module 3) Contact Blocks For All Operators 52BAK 1 NO 52BAJ 1 NC 52BJK 1 NO + 1 NC 52BAH 1 NO Early Make 52BAE 1 NC Late Break 52BAU 1 NC Extra Late Break 52BAR 1 NO + 1 NC 1) 1) Hermetically Sealed, UL Listed for Class 1, Division 2,.25A Max., 150V AC, 10 Watt.5A Max., 150V AC, 10 Watt 1 3/4 Mushroom Head Plastic For Illuminated Twist-to-Release 52RC3RR 52RC3RS 52RC3RT 1) Not available for LED. 2) For single LED, add B to end of the assembled number. 3) With 6V lamp. 4) Integrated LED module utilizes a single LED. 1) Not available for LED. 2) With 6V lamp. 3) Integrated LED module utilizes a single LED. 4) For a single LED, add XB to end of the assembled number. 7

10 Twist-to-Release Unit Cat. No. 52PR8, 52BR8 A illuminated B Non-illuminated Installation Instructions 1. Remove push-pull head (turn counter clockwise to loosen) 2. Remove locknut, lock ring, and trim ring. 3. Mount unit in panel as shown. Secure locknut to 15 ft.-lbs. 4. Replace push-pull head. Make sure gasket in in place. Contact Operation 1. For normally open contacts, use 52BAK contact block 2. For normally closed contacts, use 52BAJ contact block Notes for BlackMax 4X devices: The trim ring is not needed or supplied. Only use the index locking ring when using a metal nameplate. Discard when not using a name plate or when using a plastic nameplate. Use locknut wrench, 52MAWB. Typical spacing shown. Automotive legend requires 2¹ ₂ spacing. Some accessories also require additional spacing. 1 IMPORTANT THESE INSTRUCTIONS DO NOT PURPORT TO COVER ALL DETAILS OR VARIATIONS IN EQUIPMENT, NOR TO PROVIDE FOR EVERY POSSIBLE CONTINGENCY TO BE MET IN CONNECTION WITH INSTALLATION, OPERATION OR MAINTENANCE. SHOULD FURTHER INFORMATION BE DESIRED OR SHOULD PARTICULAR PROBLEMS ARISE WHICH ARE NOT COVERED SUFFICIENTLY FOR THE PURCHASER S PURPOSES, 1 THE MATTER SHOULD BE REFERRED TO THE LOCAL SIEMENS SALES OFFICE. Illuminated twist-to-release full voltage or transformer Ø1.79 (45) Illuminated twist-to-release LED module Ø1.79 (45) Non-illuminated twist-to-release Ø1.79 (45) THE CONTENTS OF THIS INSTRUCTION MANUAL SHALL NOT BECOME PART OF OR MODIFY ANY PRIOR OR EXISTING AGREEMENT COMMITMENT OR RELATIONSHIP. THE SALES CONTRACT CONTAINS THE ENTIRE OBLIGATION OF SIEMENS. THE WARRANTY CONTAINED IN THE CONTRACT BETWEEN THE PARTIES IS THE SOLE WARRANTY OF SIEMENS. ANY STATEMENTS CONTAINED HEREIN DO NOT CREATE NEW WARRANTIES OR MODIFY THE EXISTING WARRANTY (57) 1.75 (45) 1.74 (44) 2.01 (51) 1.75 (45) 1.74 (44) 1.75 (45) 1.74 (44) Hazardous voltage. Can cause death, serious personal injury, or property damage. To avoid electrical shock, turn off electrical power to controls before performing installation maintenance (28) Legend Plates 1.05 (27) 2.74 (70) 1.00 (25) 1.05 (27) 2.74 (70) 2.74 (70) 1.05 (27) 2.10 (53) Large Jumbo Automotive 8

11 Siemens Selector Switches 2-Position Components Operator Specific Complete Units Operators Only Contact Blocks Accessories 1) 2-Position Selector Switch Non-Illuminated Maintained A Cam 52S*2AAB*1 Chrome Short Lever A K 1 NO Chrome Long Lever B J 1 NC Black Max Short Lever X A1 NO + 1 NC Black Max Long Lever W Spring Return From Right A Cam 52S*2ACB*1 Chrome Short Lever A K 1 NO Chrome Long Lever B J 1 NC Black Max Short Lever X A1 NO + 1 NC Black Max Long Lever W 2-Position Selector Switch Non-Illuminated Maintained A Cam 52S*2AAB Chrome Short Lever A Chrome Long Lever B Black Max Short Lever X Black Max Long Lever W Spring Return From Right A Cam 52S*2ACB Chrome Short Lever A Chrome Long Lever B Black Max Short Lever X Black Max Long Lever W Contact Blocks For All Operators 52BAK 1 NO 52BAJ 1 NC 52BJK 1 NO + 1 NC 52BAH 1 NO Early Make 52BAE 1 NC Late Break 52BAU 1 NC Extra Late Break 52BAR 1 NO + 1 NC 2) 1) 52BAR 2) Hermetically Sealed, UL Listed for Class 1, Division 2,.25A Max., 200V AC, 10 Watt.5A Max., 200V AC, 10 Watt Lever Inserts For Selector Switches 52RA2*2 52RA2*3 52RA2*4 52RA2*5 52RA2*6 WHT 52RA2*8 52RA2*B A Short Lever B Long Lever 1) 2-Position Selector Switch Illuminated Maintained A Cam 52SA7A*2A0 1 NO + 1 NC 52SA7A*2A0 1 NO + 1 NC 52SA7A*2A0 1 NO + 1 NC D 24V Full Voltage G 120V Transformer H 240V Transformer 2-Position Selector Switch without Lens Illuminated Maintained A Cam 52SA7A*N D 24V Full Voltage G 120V Transformer H 240V Transformer Contact Blocks For All Operators 52BAK 1 NO 52BAJ 1 NC 52BJK 1 NO + 1 NC 52BAH 1 NO Early Make 52BAE 1 NC Late Break 52BAU 1 NC Extra Late Break 52BAR 1 NO + 1 NC 2) 1) 52BAR 2) Hermetically Sealed, UL Listed for Class 1, Division 2,.25A Max., 200V AC, 10 Watt.5A Max., 200V AC, 10 Watt Lens Kit (Knob plus Insert) For Illuminated Selector Switches 52RA6P2 52RA6P3 52RA6P5 52RA6P9 CLR 52RA6PA WHT 52RA6PB 1) 2-Position Key Selector Switch Maintained A Cam 52SC6AF*1 K 1 NO J 1 NC A 1 NO + 1 NC Spring Return From Right A Cam 52SC6AX*1 K 1 NO J 1 NC A 1 NO + 1 NC 2-Position Key Selector Switch Maintained A Cam 52SC6A* E All Key Removal F Left Key Removal Contact Blocks For All Operators 52BAK 1 NO 52BAJ 1 NC 52BJK 1 NO + 1 NC 52BAH 1 NO Early Make 52BAE 1 NC Late Break 52BAU 1 NC Extra Late Break 52BAR 1 NO + 1 NC 2) 1) 52BAR 2) Hermetically Sealed, UL Listed for Class 1, Division 2,.25A Max., 200V AC, 10 Watt.5A Max., 200V AC, 10 Watt 9

12 A Selector Operators Non-Illuminated Cat. No. 52SA2, 52SB2, 52SX2, 52SW2 and 52SC6 For Contact and Cam Selection for Non-Illuminated Selector and Key Operators, see Page 1-28 A Selector Operators Non-illuminated 2 1/8 1 5/8 1 5/8 B Selector Operators Illuminated Cat. No. 52SA7 For Contact and Cam Selection for Illuminated Selector Operators, see Page /8 2 3/8 Installation Instructions Units are assembled as shown. 1. Position and press in color insert if required. 2. Assemble oil rings. 3. Mount unit on panel as shown in the illustration. 4. Position trim ring or legend plate (trim ring is discarded when legend plate is used). 1) 5. Position index locking ring on unit as shown in illustration. 2) 6. Assemble and tighten lock nut to 15 ft. lbs. To add another color insert, remove unit from panel and pry out white insert with small screwdriver. Snap in new color insert. Typical spacing shown. Automotive legend requires 2¹ ₂ spacing. 1) Trim ring not used on black 4X devices. 2) Locking ring not needed with plastic legend plates. B Selector Operators Illuminated Notes for BlackMax 4X devices: The trim ring is not needed or supplied. Only use the index locking ring when using a metal nameplate. Discard when not using a name plate or when using a plastic nameplate. Use locknut wrench, 52MAWB. IMPORTANT THESE INSTRUCTIONS DO NOT PURPORT TO COVER ALL DETAILS OR VARIATIONS IN EQUIPMENT, NOR TO PROVIDE FOR EVERY POSSIBLE CONTINGENCY TO BE MET IN CONNECTION WITH INSTALLATION, OPERATION OR MAINTENANCE. SHOULD FURTHER INFORMATION BE DESIRED OR SHOULD PARTICULAR PROBLEMS ARISE WHICH ARE NOT COVERED SUFFICIENTLY FOR THE PURCHASER S PURPOSES, THE MATTER SHOULD BE REFERRED TO THE LOCAL SIEMENS SALES OFFICE. THE CONTENTS OF THIS INSTRUCTION MANUAL SHALL NOT BECOME PART OF OR MODIFY ANY PRIOR OR EXISTING AGREEMENT COMMITMENT OR RELATIONSHIP. THE SALES CONTRACT CONTAINS THE ENTIRE OBLIGATION OF SIEMENS. THE WARRANTY CONTAINED IN THE CONTRACT BETWEEN THE PARTIES IS THE SOLE WARRANTY OF SIEMENS. ANY STATEMENTS CONTAINED HEREIN DO NOT CREATE NEW WARRANTIES OR MODIFY THE EXISTING WARRANTY. 1 15/16 1 5/8 1 5/ /8 2 3/8 Typical spacing shown. Automotive legend requires 2¹ ₂ spacing. Volts Lamps 6-8* # # #120MB *Also transformer type Hazardous voltage. Can cause death, serious personal injury, or property damage. To avoid electrical shock, turn off electrical power to controls before performing installation maintenance. Selector switches and keyed selector switches illuminated and non-illuminated Legend Plates Large Jumbo Automotive 10

13 Siemens Selector Switches 3-Position Components Operator Specific Complete Units Operators Only Contact Blocks Accessories 3-Position Selector Switch Non-Illuminated Maintained 52S*2* AB * Chrome Short Lever A C 1) A1 1 NO + 1 NC Chrome Long Lever B G 1) A2 2 NO + 2 NC Black Max Short Lever X J2K12 NC + 1 NO Black Max Long Lever W 1) Cam code Spring Return From Right 52S*2* CB * Chrome Short Lever A C 1) A1 1 NO + 1 NC Chrome Long Lever B G1) A2 2 NO + 2 NC Black Max Short Lever X J2 K1 2 NC + 1 NO Black Max Long Lever W 1) Cam code Spring Return From Left 52S*2* BB * Chrome Short Lever A C 1) A1 1 NO + 1 NC Chrome Long Lever B G1) A2 2 NO + 2 NC Black Max Short Lever X J2K1 2 NC + 1 NO Black Max Long Lever W 1) Cam code 3-Position Selector Switch Non-Illuminated Maintained 52S*2* AB Chrome Short Lever A B 1) Chrome Long Lever B C 1) Black Max Short Lever X D 1) Black Max Long Lever W E 1) G 1) 1) Cam code Spring Return From Right 52S*2* CB Chrome Short Lever A B 1) Chrome Long Lever B C 1) Black Max Short Lever X D 1) Black Max Long Lever W E 1) G 1) 1) Cam code Spring Return From Left 52S*2* BB Chrome Short Lever A B 1) Chrome Long Lever B C 1) Black Max Short Lever X D 1) Black Max Long Lever W E 1) G 1) 1) Cam code Contact Blocks For All Operators 52BAK 1 NO 52BAJ 1 NC 52BJK 1 NO + 1 NC 52BAH 1 NO Early Make 52BAE 1 NC Late Break 52BAU 1 NC Extra Late Break 52BAR 1 NO + 1 NC 2) 1) 52BAR 2) Hermetically Sealed, UL Listed for Class 1, Division 2,.25A Max., 200V AC, 10 Watt.5A Max., 200V AC, 10 Watt 1) Lever Inserts For Selector Switches 52RA2*2 52RA2*3 52RA2*4 52RA2*5 52RA2*8 52RA2*6 WHT 52RA2*B A Short Lever B Long Lever Spring Return From Right and Left 52S*2* DB * Chrome Short Lever A C 1) A1 1 NO + 1 NC Chrome Long Lever B G1) A2 2 NO + 2 NC Black Max Short Lever X J2K1 2 NC + 1 NO Black Max Long Lever W 1) Cam code Spring Return From Right and Left 52S*2* DB Chrome Short Lever A B 1) Chrome Long Lever B C 1) Black Max Short Lever X D 1) Black Max Long Lever W E 1) G 1) 1) Cam code 1) 3-Position Selector Switch Illuminated Maintained 52SA7* *2 52SA7* *3 52SA7* *9 B1) D 24V Full Voltage C1) G 120V Transformer H 240V Transformer 1) Cam code 3-Position Selector Switch without Lens Illuminated Maintained 52SA7* *N B1) D 24V Full Voltage C1) G 120V Full Voltage Transformer H 240V Transformer 1) Cam code Contact Blocks For All Operators 52BAK 1 NO 52BAJ 1 NC 52BJK 1 NO + 1 NC 52BAH 1 NO Early Make 52BAE 1 NC Late Break 52BAU 1 NC Extra Late Break 52BAR 1 NO + 1 NC 2) 1) 52BAR 2) Hermetically Sealed, UL Listed for Class 1, Division 2,.25A Max., 200V AC, 10 Watt.5A Max., 200V AC, 10 Watt Lens Kit (Knob plus Insert) For Illuminated Selector Switches 52RA6P2 52RA6P3 52RA6P5 CL 52RA6P9 52RA6PA WH 52RA6PB 11

14 A Selector Operators Non-illuminated Cat. No. 52SA2, 52SB2, 52SX2, 52SW2 and 52SC6 For Contact and Cam Selection for Non-Illuminated Selector and Key Operators, see Page 1-28 A Selector Operators Non-illuminated 2 1/8 1 5/8 1 5/8 B Selector Operators Illuminated Cat. No. 52SA7 For Contact and Cam Selection for Illuminated Selector Operators, see Page /8 2 3/8 Installation Instructions Units are assembled as shown. 1. Position and press in color insert if required. 2. Assemble oil rings. 3. Mount unit on panel as shown in the illustration. 4. Position trim ring or legend plate (trim ring is discarded when legend plate is used).1) 5. Position index locking ring on unit as shown in illustration.2) 6. Assemble and tighten lock nut to 15 ft. lbs. To add another color insert, remove unit from panel and pry out white insert with small screwdriver. Snap in new color insert. Typical spacing shown. Automotive legend requires 2¹ ₂ spacing. 1) Trim ring not used on black 4X devices. 2) Locking ring not needed with plastic legend plates. B Selector Operators Illuminated Notes for BlackMax 4X devices: The trim ring is not needed or supplied. Only use the index locking ring when using a metal nameplate. Discard when not using a name plate or when using a plastic nameplate. Use locknut wrench, 52MAWB. IMPORTANT THESE INSTRUCTIONS DO NOT PURPORT TO COVER ALL DETAILS OR VARIATIONS IN EQUIPMENT, NOR TO PROVIDE FOR EVERY POSSIBLE CONTINGENCY TO BE MET IN CONNECTION WITH INSTALLATION, OPERATION OR MAINTENANCE. SHOULD FURTHER INFORMATION BE DESIRED OR SHOULD PARTICULAR PROBLEMS ARISE WHICH ARE NOT COVERED SUFFICIENTLY FOR THE PURCHASER S PURPOSES, THE MATTER SHOULD BE REFERRED TO THE LOCAL SIEMENS SALES OFFICE. THE CONTENTS OF THIS INSTRUCTION MANUAL SHALL NOT BECOME PART OF OR MODIFY ANY PRIOR OR EXISTING AGREEMENT COMMITMENT OR RELATIONSHIP. THE SALES CONTRACT CONTAINS THE ENTIRE OBLIGATION OF SIEMENS. THE WARRANTY CONTAINED IN THE CONTRACT BETWEEN THE PARTIES IS THE SOLE WARRANTY OF SIEMENS. ANY STATEMENTS CONTAINED HEREIN DO NOT CREATE NEW WARRANTIES OR MODIFY THE EXISTING WARRANTY. 1 15/16 1 5/8 1 5/ /8 2 3/8 Typical spacing shown. Automotive legend requires 2¹ ₂ spacing. Volts Lamps 6-8* # # #120MB *Also transformer type Hazardous voltage. Can cause death, serious personal injury, or property damage. To avoid electrical shock, turn off electrical power to controls before performing installation maintenance. Selector switches and keyed selector switches illuminated and non-illuminated Legend Plates Large Jumbo Automotive 12

15 Siemens Selector Switches 3-Position Components Operator Specific Complete Units Operators Only Contact Blocks Accessories 3-Position Key Selector Switch Maintained 52SC6CEA1 1 NO + 1 NC 52SC6CEJ2K1 1 NO + 2 NC 52SC6CEA2 2 NO + 2 NC Spring Return From Right 52SC6CZA1 1 NO + 1 NC 52SC6GZJ2K1 1 NO + 2 NC 52SC6CZA2 2 NO + 2 NC 3-Position Key Selector Switch Maintained 52SC6 * * B1) E All Key Removal C1) F Left Key Removal D1) G Right Key Removal E 1) H Center Key Removal G1) J Left and Right Key K Removal Left and Center Key Removal M Right and Center 1) Cam Code Key Removal 52SC6 * * Spring Return From Right 1) Cam Code Spring Return From Left 52SC6 * * B 1) U Center Key Removal C1) Z Left and Center D1) Key Removal E 1) G1) B 1) T Center Key Removal C1) W Right Key Removal D1) Y Right and Center E1) Key Removal 1) Cam Code G1) Contact Blocks For All Operators 52BAK 1 NO 52BAJ 1 NC 52BJK 1 NO + 1 NC 52BAH 1 NO Early Make 52BAE 1 NC Late Break 52BAU 1 NC Extra Late Break 52BAR 1 NO + 1 NC 2) 1) 52BAR 2) Hermetically Sealed, UL Listed for Class 1, Division 2,.25A Max., 200V AC, 10 Watt.5A Max., 200V AC, 10 Watt 1) Spring Return From Right and Left 52SC6CVA1 1 NO + 1 NC 52SC6GVJ2K1 1 NO + 2 NC 52SC6CVA2 2 NO + 2 NC 52SC6 * * Spring Return From Right and Left B 1) V Center Key Removal C 1) D1) E 1) G1) 1) Cam Code 13

16 Selector Operators Non-Illuminated Cat. No. 52SC6 For Contact and Cam Selection for Non-Illuminated Selector and Key Operators, see Page /8 2 1/8 1 5/8 Installation Instructions Units are assembled as shown. 1. Position and press in color insert if required. 2. Assemble oil rings. 3. Mount unit on panel as shown in the illustration. 4. Position trim ring or legend plate (trim ring is discarded when legend plate is used). 1) 5. Position index locking ring on unit as shown in illustration. 2) 6. Assemble and tighten lock nut to 15 ft. lbs /8 2 3/8 1) Trim ring not used on black 4X devices. 2) Locking ring not needed with plastic legend plates Notes for BlackMax 4X devices: The trim ring is not needed or supplied. Only use the index locking ring when using a metal nameplate. Discard when not using a name plate or when using a plastic nameplate. Use locknut wrench, 52MAWB. To add another color insert, remove unit from panel and pry out white insert with small screwdriver. Snap in new color insert. Typical spacing shown. Automotive legend requires 2¹ ₂ spacing. IMPORTANT THESE INSTRUCTIONS DO NOT PURPORT TO COVER ALL DETAILS OR VARIATIONS IN EQUIPMENT, NOR TO PROVIDE FOR EVERY POSSIBLE CONTINGENCY TO BE MET IN CONNECTION WITH INSTALLATION, OPERATION OR MAINTENANCE. SHOULD FURTHER INFORMATION BE DESIRED OR SHOULD PARTICULAR PROBLEMS ARISE WHICH ARE NOT COVERED SUFFICIENTLY FOR THE PURCHASER S PURPOSES, THE MATTER SHOULD BE REFERRED TO THE LOCAL SIEMENS SALES OFFICE. THE CONTENTS OF THIS INSTRUCTION MANUAL SHALL NOT BECOME PART OF OR MODIFY ANY PRIOR OR EXISTING AGREEMENT COMMITMENT OR RELATIONSHIP. THE SALES CONTRACT CONTAINS THE ENTIRE OBLIGATION OF SIEMENS. THE WARRANTY CONTAINED IN THE CONTRACT BETWEEN THE PARTIES IS THE SOLE WARRANTY OF SIEMENS. ANY STATEMENTS CONTAINED HEREIN DO NOT CREATE NEW WARRANTIES OR MODIFY THE EXISTING WARRANTY. Selector switches and keyed selector switches illuminated and non-illuminated Legend Plates Large Jumbo Automotive Hazardous voltage. Can cause death, serious personal injury, or property damage. To avoid electrical shock, turn off electrical power to controls before performing installation maintenance. 14

17 Siemens Selector Switches 4-Position and Specialty Components Operator Specific Complete Units Operators Only Contact Blocks Accessories 1) 4-Position Selector Switch Non-Illuminated Maintained 52S*2HAB Chrome Short Lever A Chrome Long Lever B Black Max Short Lever X Black Max Long Lever W Contact Blocks For All Operators 52BAK 1 NO 52BAJ 1 NC 52BJK 1 NO + 1 NC 52BAH 1 NO Early Make 52BAE 1 NC Late Make 52BAU 1 NC Extra Late Break 52BAR 1 NO + 1 NC 2) 1) 52BAR 2) Hermetically Sealed, UL Listed for Class 1, Division 2,.25A Max., 200V AC, 10 Watt.5A Max., 200V AC, 10 Watt Select/Push Operator Non-Illuminated Maintained 52SA** 52SA** 1 2 Flush 3 P 1) Raised 4 Q 1) R 1) S 1) 1) Cam code 15

18 Selector Operators Non-Illuminated Cat. No. 52SA2H, 52SB2H, 52SX2H, 52SW2H, 52SA3, 52SA4 For Contact and Cam Selection for Non-Illuminated Selector and Key Operators, see Page /8 2 1/8 1 5/8 Installation Instructions Units are assembled as shown. 1. Position and press in color insert if required. 2. Assemble oil rings. 3. Mount unit on panel as shown in the illustration. 4. Position trim ring or legend plate (trim ring is discarded when legend plate is used).1) 5. Position index locking ring on unit as shown in illustration.2) 6. Assemble and tighten lock nut to 15 ft. lbs /8 2 3/8 1) Trim ring not used on black 4X devices. 2) Locking ring not needed with plastic legend plates Notes for BlackMax 4X devices: The trim ring is not needed or supplied. Only use the index locking ring when using a metal nameplate. Discard when not using a name plate or when using a plastic nameplate. Use locknut wrench, 52MAWB. To add another color insert, remove unit from panel and pry out white insert with small screwdriver. Snap in new color insert. Typical spacing shown. Automotive legend requires 2¹ ₂ spacing. IMPORTANT THESE INSTRUCTIONS DO NOT PURPORT TO COVER ALL DETAILS OR VARIATIONS IN EQUIPMENT, NOR TO PROVIDE FOR EVERY POSSIBLE CONTINGENCY TO BE MET IN CONNECTION WITH INSTALLATION, OPERATION OR MAINTENANCE. SHOULD FURTHER INFORMATION BE DESIRED OR SHOULD PARTICULAR PROBLEMS ARISE WHICH ARE NOT COVERED SUFFICIENTLY FOR THE PURCHASER S PURPOSES, THE MATTER SHOULD BE REFERRED TO THE LOCAL SIEMENS SALES OFFICE. THE CONTENTS OF THIS INSTRUCTION MANUAL SHALL NOT BECOME PART OF OR MODIFY ANY PRIOR OR EXISTING AGREEMENT COMMITMENT OR RELATIONSHIP. THE SALES CONTRACT CONTAINS THE ENTIRE OBLIGATION OF SIEMENS. THE WARRANTY CONTAINED IN THE CONTRACT BETWEEN THE PARTIES IS THE SOLE WARRANTY OF SIEMENS. ANY STATEMENTS CONTAINED HEREIN DO NOT CREATE NEW WARRANTIES OR MODIFY THE EXISTING WARRANTY. Selector Push Operator Legend Plates Large Jumbo Automotive Hazardous voltage. Can cause death, serious personal injury, or property damage. To avoid electrical shock, turn off electrical power to controls before performing installation maintenance. Selector switches and keyed selector switches illuminated and non-illuminated 16

19 Siemens Push-Pull Units Components Operator Specific Complete Units Operators Only Contact Blocks Accessories 1) 2-Position Push-Pull; Maintained Non-Illuminated 1³ ₄ Metal Mushroom Head Less Head 52*P2AZA 1 NO + 1 NC MTL 52*P2A2A 1 NO + 1 NC MTL 52*P2A3A 1 NO + 1 NC MTL 52*P2ACA 1 NO + 1 NC Chrome P BlackMax B 1³ ₄ Plastic Mushroom Head Less Head 52*P2WZA 1 NO + 1 NC 52*P2W1A 1 NO + 1 NC 52*P2W2A 1 NO + 1 NC 52*P2W3A 1 NO + 1 NC Chrome P BlackMax B 2-Position Push-Pull; Maintained Non-Illuminated 1³ ₄ Metal Mushroom Head Less Head 52*P2AZ MTL MTL 52*P2A2 MTL 52*P2A3 52*P2AC Chrome P BlackMax B 1³ ₄ Plastic Mushroom Head Less Head 52*P2WZ 52*P2W1 52*P2W2 52*P2W3 Chrome P BlackMax B Contact Blocks For All Operators 52BAK 1 NO 52BAJ 1 NC 52BJK 1 NO + 1 NC 52BAH 1 NO Early Make 52BAE 1 NC Late Break 52BAU 1 NC Extra Late Break 52BAR 1 NO + 1 NC 2) 1) 52BAR 2) Hermetically Sealed, UL Listed for Class 1, Division 2,.25A Max., 200V AC, 10 Watt.5A Max., 200V AC, 10 Watt 1³ ₄ Mushroom Head Plastic For Non-Illuminated Push-Pull 52RC3D2 52RC3D1 52RC3D3 52RC3D5 52RC3D4 52RC3D6 52RC3D8 Kit All Colors 52RC3DN 2¹ ₂ Plastic Mushroom Head Less Head 52*P2VZA 1 NO + 1 NC 52*P2V1A 1 NO + 1 NC 52*P2V2A 1 NO + 1 NC 52*P2V3A 1 NO + 1 NC Chrome P BlackMax B 2¹ ₂ Plastic Mushroom Head Less Head 52*PAVZ 52*P2V1 52*P2V2 52*P2V3 Chrome P BlackMax B 1³ ₄ Mushroom Head Metal For Non-Illuminated Push-Pull MTL MTL 52RC2FC MTL 52RC2F2 52RC2F3 3-Position Push-Pull; Momentary Non-Illuminated 1³ ₄ Metal Mushroom Head Less Head 52*P3AZU 1 NO + 1 NCXLB 1) 3TL 52*P3A1U 1 NO + 1 NCXLB1) CTL 52*P3A2U 1 NO + 1 NCXLB1) MTL 52*P3A3U 1 NO + 1 NCXLB1) Chrome P Black Max B 1³ ₄ Plastic Mushroom Head Less Head 52*P3WZU 1 NO + 1 NCXLB 1) 52*P3W1U 1 NO + 1 NCXLB1) 52*P3W2U 1 NO + 1 NCXLB1) 52*P3W3U 1 NO + 1 NCXLB1) Chrome P BlackMax B 2¹ ₂ (57.2mm) Plastic Mushroom Head Less Head 52*P3VZU 1 NO + 1 NCXLB 1) 52*P3V1U 1 NO + 1 NCXLB1) 52*P2V2U 1 NO + 1 NCXLB1) 52*PCV3U 1 NO + 1 NCXLB1) Chrome P Black Max B 1) Blocks cannot be interchanged (start-stop) circuit. 2¹ ₂ Mushroom Head Plastic For Non-Illuminated Push-Pull 52RC3E1 52RC3E2 52RC3E3 52RC3E4 52RC3E5 52RC3E6 52RC3E8 Kit All Colors 52RC3EN 17

20 Non-Illuminated Push-Pull Operators 2 Position Maintained, 3 Position Momentary Cat. No. 52PP2A, 52PP2W, 52PP2V, 52PP3A, 52PP3W, 52PP3V, 52BP2A, 52BP2W, 52BP2V, 52BP3A, 52BP3W, 52BP3V Installation Instructions 1. Remove push-pull head (turn counter clockwise to loosen). 2. Remove locknut, lock ring, and trim ring. 3. Mount unit in panel as shown. Secure locknut to 15 ft.-lbs. 4. Replace push-pull head. Make sure gasket in in place. Contact Operation Maintained Push-Pull 1. For normally open contacts, use 52BAK contact block. 2. For normally closed contacts, use 52BAJ contact block. Momentary Push-Pull (Factory assembled) 1. For normally open contacts, the 52BAJ (normally closed) contact block is used. When mounted on this operator, the contact block becomes normally open. 2. For normally closed contacts, the special 52BAU contact block is used. This contact block must be mounted last. Notes for BlackMax 4X devices: The trim ring is not needed or supplied. Only use the index locking ring when using a metal nameplate. Discard when not using a name plate or when using a plastic nameplate. Use locknut wrench, 52MAWB. Typical spacing shown. Automotive legend requires 2¹ ₂ spacing. Some accessories also require additional spacing. 1 3/4" mushroom head push-pull non-illuminated 1.75 (45) Ø1.75 (44) 2 1/2" mushroom head push-pull non-illuminated 1.75 (45) Ø2.50 (64) IMPORTANT THESE INSTRUCTIONS DO NOT PURPORT TO COVER ALL DETAILS OR VARIATIONS IN EQUIPMENT, NOR TO PROVIDE FOR EVERY POSSIBLE CONTINGENCY TO BE MET IN CONNECTION WITH INSTALLATION, OPERATION OR MAINTENANCE. SHOULD FURTHER INFORMATION BE DESIRED OR SHOULD PARTICULAR PROBLEMS ARISE WHICH ARE NOT COVERED SUFFICIENTLY FOR THE PURCHASER S PURPOSES, THE MATTER SHOULD BE REFERRED TO THE LOCAL SIEMENS SALES OFFICE (70) 1.74 (44) 2.74 (70) 1.74 (44) THE CONTENTS OF THIS INSTRUCTION MANUAL SHALL NOT BECOME PART OF OR MODIFY ANY PRIOR OR EXISTING AGREEMENT COMMITMENT OR RELATIONSHIP. THE SALES CONTRACT CONTAINS THE ENTIRE OBLIGATION OF SIEMENS. THE WARRANTY CONTAINED IN THE CONTRACT BETWEEN THE PARTIES IS THE SOLE WARRANTY OF SIEMENS. ANY STATEMENTS CONTAINED HEREIN DO NOT CREATE NEW WARRANTIES OR MODIFY THE EXISTING WARRANTY. Legend Plates 1.05 (27) 2.10 (53) 1.05 (27) 2.10 (53) Hazardous voltage. Can cause death, serious personal injury, or property damage. To avoid electrical shock, turn off electrical power to controls before performing installation maintenance. Large Automotive 18

21 Siemens Push-Pull Units Components Operator Specific Complete Units Operators Only Contact Blocks Accessories 1) 2-Position Push-Pull; Maintained Illuminated 1 ³ ₄ Metal Mushroom Head Less Head 52*P2*ZA 1NO +1 NC 52*P2*2A 1NO +1 NC 52*P2*3A 1NO +1 NC 52*P2*9A 1NO +1 NC Chrome P D 24V Full Voltage 1) BlackMax B G 120V Transformer 1) 2) H 240V Transformer 1) 2) J 480V Transformer 1) 2) K 600V Transformer 1) 2) L 24V LED Module 3) M 120V LED Module 3) N 240V LED Module 3) 2-Position, Maintained Push-Pull Illuminated 1 ³ ₄ Metal Mushroom Head Less Head 52*P2*Z 52*P2*9 Chrome P D 24V Full Voltage 1) BlackMax B G 120V Transformer 1) 2) H 240V Transformer 1) 2) J 480V Transformer 1) 2) K 600V Transformer 1) 2) L 24V LED Module 3) M 120V LED Module 3) N 240V LED Module 3) Contact Blocks For All Operators 52BAK 1 NO 52BAJ 1 NC 52BJK 1 NO + 1 NC 52BAH 1 NO Early Make 52BAE 1 NC Late Break 52BAU 1 NC Extra Late Break 52BAR 1 NO + 1 NC 2) 1) 52BAR 2) Hermetically Sealed, UL Listed for Class 1, Division 2,.25A Max., 200V AC, 10 Watt.5A Max., 200V AC, 10 Watt 1³ ₄ Mushroom Head Metal For Illuminated Push-Pull 52R*3H2 52R*3H3 52R*3H5 52R*3H9 CLR 52R*3HA WHT 52R*3HB Chrome B BlackMax X 1 ³ ₄ Plastic Mushroom Head Less Head 52*P2*ZA 1NO +1 NC 52*P2*RA 1NO +1 NC 52*P2*SA 1NO +1 NC 52*P2*TA 1NO +1 NC Chrome P D 24V Full Voltage 1) BlackMax B G 120V Transformer 1) 2) L 24V LED Module 3) M 120V LED Module 3) 1 ³ ₄ Plastic Mushroom Head Less Head 52*P2*Z 52*P2*R 52*P2*S 52*P2*T Chrome P D 24V Full Voltage 1) BlackMax B G 120V Transformer 1) 2) L 24V LED Module 3) M 120V LED Module 3) 1³ ₄ Mushroom Head Plastic For Illuminated Push-Pull 52RC3JR 52RC3JS 52RC3JT 2 ¹ ₂ Plastic Mushroom Head Less Head 52*P2*PA 1NO +1 NC 52*P2*DA 1NO +1 NC 52*P2*EA 1NO +1 NC 52*P2*FA 1NO +1 NC Chrome P D 24V Full Voltage 1) BlackMax B G 120V Transformer 1) 2) L 24V LED Module 3) M 120V LED Module 3) 2 ¹ ₂ Plastic Mushroom Head Less Head 52*P2*Z 52*P2*D 52*P2*E 52*P2*F Chrome P D 24V Full Voltage 1) BlackMax B G 120V Transformer 1) 2) L 24V LED Module 3) M 120V LED Module 3) 2¹ ₂ Plastic Mushroom Head For Illuminated Push-Pull 52RC3KR 52RC3KS 52RC3KT 1) For LED, add B to the end of assembled number. 2) With 6V lamp. 3) With single LED. 1) For LED, add XB to the end of assembled number. 2) With 6V lamp. 3) With single LED. 19

22 Illuminated Push-Pull Operators 2 Position Maintained Cat. No. 52PP2, 52BP2 Installation Instructions 1. Remove push-pull head (turn counter clockwise to loosen). 2. Remove locknut, lock ring, and trim ring. 3. Mount unit in panel as shown. Secure locknut to 15 ft.-lbs. 4. Replace push-pull head. Make sure gasket in in place. Contact Operation 1. For normally open contacts,use 52BAK contact block 2. For normally closed contacts, use 52BAJ contact block Notes for BlackMax 4X devices: The trim ring is not needed or supplied. Only use the index locking ring when using a metal nameplate. Discard when not using a name plate or when using a plastic nameplate. Use locknut wrench, 52MAWB. Typical spacing shown. Automotive legend requires 2¹ ₂ spacing. Some accessories also require additional spacing. IMPORTANT THESE INSTRUCTIONS DO NOT PURPORT TO COVER ALL DETAILS OR VARIATIONS IN EQUIPMENT, NOR TO PROVIDE FOR EVERY POSSIBLE CONTINGENCY TO BE MET IN CONNECTION WITH INSTALLATION, OPERATION OR MAINTENANCE. SHOULD FURTHER INFORMATION BE DESIRED OR SHOULD PARTICULAR PROBLEMS ARISE WHICH ARE NOT COVERED SUFFICIENTLY FOR THE PURCHASER S PURPOSES, THE MATTER SHOULD BE REFERRED TO THE LOCAL SIEMENS SALES OFFICE. 1 3/4" plastic mushroom head push-pull illuminated Ø1.75 (45) 1 3/4" metal mushroom head push-pull illuminated Ø1.75 (45) Wiring Contact Position Maintained 2 Position THE CONTENTS OF THIS INSTRUCTION MANUAL SHALL NOT BECOME PART OF OR MODIFY ANY PRIOR OR EXISTING AGREEMENT COMMITMENT OR RELATIONSHIP. THE SALES CONTRACT CONTAINS THE ENTIRE OBLIGATION OF SIEMENS. THE WARRANTY CONTAINED IN THE CONTRACT BETWEEN THE PARTIES IS THE SOLE WARRANTY OF SIEMENS. ANY STATEMENTS CONTAINED HEREIN DO NOT CREATE NEW WARRANTIES OR MODIFY THE EXISTING WARRANTY (45) 2.25 (57) 1.74 (44) 2.25 (57) 1.88 (48) 1.74 (44) Hazardous voltage. Can cause death, serious personal injury, or property damage. To avoid electrical shock, turn off electrical power to controls before performing installation maintenance (28) 1.05 (27) 2.74 (70) 1.09 (28) 1.05 (27) 2.74 (70) Legend Plates Large Jumbo Automotive 20

23 Siemens Push-Pull Operators Components Operator Specific Complete Units Operators Only Contact Blocks Accessories 3-Position Push-Pull; Momentary Illuminated 1 ³ ₄ Metal Mushroom Head Less Head 52*P3*ZU 1NO +1 NCXLB3) 52*P3*2U 1NO +1 NCXLB3) 52*P3*3U 1NO +1 NCXLB3) 52*P3*9U Chrome P D 24V Full Voltage 1) BlackMax B G 120V Transformer 1) 2) H 240V Transformer 1) 2) J 480V Transformer 1) 2) K 600V Transformer 1) 2) L 24V LED Module 4) M 120V LED Module 4) N 240V LED Module 4) 1³ ₄ Mushroom Head Metal For Illuminated Push-Pull CLR WHT Chrome BlackMax 52R*3H2 52R*3H3 52R*3H5 52R*3H9 52R*3HA 52R*3HB B X 1 ³ ₄ Plastic Mushroom Head Less Head 52*P3*ZU 1NO +1 NCXLB3) 52*P3*RU 1NO +1 NCXLB3) 52*P3*SU 1NO +1 NCXLB3) 52*P3*TU 1NO +1 NCXLB3) Chrome P D 24V Full Voltage 1) BlackMax B G 120V Transformer 1) 2) L 24V LED Module 4) M 120V LED Module 4) 1³ ₄ Plastic Mushroom Head For Illuminated Push-Pull 52RC3JR 52RC3JS 52RC3JT 2 ¹ ₂ Plastic Mushroom Head Less Head 52*P3*ZU 1NO +1 NCXLB3) 52*P3*DU 1NO +1 NCXLB3) 52*P3*EU 1NO +1 NCXLB3) 52*P3*FU 1NO +1 NCXLB3) Chrome P D 24V Full Voltage 1) BlackMax B G 120V Transformer 1) 2) L 24V LED Module 4) M 120V LED Module 2¹ ₂ Plastic Mushroom Head For Illuminated Push-Pull 52RC3KR 52RC3KS 52RC3KT 1) For LED, add B to the end of assembled number. 2) With 6V lamp. 3) Blocks cannot be interchanged (start-stop circuit). 4) With single LED. 21

24 Illuminated Push-Pull Operators 3 Position Momentary Cat. No. 52PP3, 52BP3 Installation Instructions 1. Remove push-pull head (turn counter clockwise to loosen). 2. Remove locknut, lock ring, and trim ring. 3. Mount unit in panel as shown. Secure locknut to 15 ft.-lbs. 4. Replace push-pull head. Make sure gasket in in place. Contact Operation 1. For normally open contacts, the 52BAJ (normally closed) contact block is used. When mounted on this operator, the contact block becomes normally open. 2. For normally closed contacts, the special 52BAU contact block is used. This contact block must be mounted last. Typical spacing shown. Automotive legend requires 2¹ ₂ spacing. Some accessories also require additional spacing. Notes for BlackMax 4X devices: The trim ring is not needed or supplied. Only use the index locking ring when using a metal nameplate. Discard when not using a name plate or when using a plastic nameplate. Use locknut wrench, 52MAWB. IMPORTANT THESE INSTRUCTIONS DO NOT PURPORT TO COVER ALL DETAILS OR VARIATIONS IN EQUIPMENT, NOR TO PROVIDE FOR EVERY POSSIBLE CONTINGENCY TO BE MET IN CONNECTION WITH INSTALLATION, OPERATION OR MAINTENANCE. SHOULD FURTHER INFORMATION BE DESIRED OR SHOULD PARTICULAR PROBLEMS ARISE WHICH ARE NOT COVERED SUFFICIENTLY FOR THE PURCHASER S PURPOSES, THE MATTER SHOULD BE REFERRED TO THE LOCAL SIEMENS SALES OFFICE. 1 3/4" plastic mushroom head illuminated Ø1.75 (45) 1.75 (45) 1 3/4" metal mushroom head illuminated Ø1.75 (45) 1.88 (48) Momentary Contact 3 Position THE CONTENTS OF THIS INSTRUCTION MANUAL SHALL NOT BECOME PART OF OR MODIFY ANY PRIOR OR EXISTING AGREEMENT COMMITMENT OR RELATIONSHIP. THE SALES CONTRACT CONTAINS THE ENTIRE OBLIGATION OF SIEMENS. THE WARRANTY CONTAINED IN THE CONTRACT BETWEEN THE PARTIES IS THE SOLE WARRANTY OF SIEMENS. ANY STATEMENTS CONTAINED HEREIN DO NOT CREATE NEW WARRANTIES OR MODIFY THE EXISTING WARRANTY (57) 1.74 (44) 2.74 (70) 2.25 (57) 1.74 (44) 2.74 (70) Hazardous voltage. Can cause death, serious personal injury, or property damage (28) 1.05 (27) 1.09 (28) 1.05 (27) To avoid electrical shock, turn off electrical power to controls before performing installation maintenance. Legend Plates Large Jumbo Automotive 22