More Commercial Equipment by TurfVent.

Transcription

1 TM EARTH AUGERS THERE IS A BADGER EARTH AUGER FOR ANY PROJECT SIZE. LIGHTWEIGHT - Lightweight unit for use by one person or two. AUGER - Equipped with Carbide Tipped Pilot Point, Augers are available in diameters from 2 to 12. PORTABLE - Easy to move from one place to another. WIDE STANCE CONTOUR HANDLES - Provides positive grip and Control. (Cushion Contour on the BADGER Plus) Offered as a kit, the affordable BADGER BUDDY BAR bolts onto any BADGER earth auger to convert it from a one-man to a two-man unit in seconds! More Commercial Equipment by TurfVent POWERHEAD Powerhead Weight - 19 lbs Engine - Two Horsepower, 49.2c.c. Two Stroke Engine Gear Box - 28:1 gear ratio, Six Sealed Ball Bearings, Centrifugal Clutch, Heated Gears, Factory Lubricated and Sealed, Clockwise Rotation. Engine Controls - Easy Access Choke and Run-Stop Control Switch, Thumb Actuated Throttle Linkage Rod. A FEW OF THE USES FOR A BADGER ARE: Fencing Deck Installation Trail Markers Bulb Planting Signs Tree/Shrub Planting Support Poles Soil Testing Deep Root Fertilization Ice Fishing (with optional ice drill) Jiffy Ice Drill Assembly 8 Diameter Part # 1882 Tune up your Power Drill with Jiffy-Badger Spark Plug Fuel Cap fits all 2HP Drills with Tecumseh Engines Powered by TECUMSEH Engines 8 Left Hand Earth Auger Blade BADGER AUGER DETAIL: Full Flighted Auger GEAR BOX Two Stage 28-1 Gear Ratio Rugged Heat Treated Side Blade, Easy Replacement! Six Sealed Ball Bearings Alluminum Alloy Gear Case Long Life CARBIDE Tipped Pilot Point Factory Lubricated and Sealed Centrifugal Clutch Heat Treated Steel Gears Output Shaft: 160 rpm, Clockwise Rotation ENGINEERING AND MANUFACTURING CO., INC. 520 FOREST AVENUE SHEBOYGAN FALLS, WI PHONE: Canada FAX admin@jiffyonice.com

2 TurfVent SeriesTwo Lawn Aerator Models TV 32, TV 40, TV 48 The BEST Next to Mother Earth GM3298 (05/09) Page 1

3 ASSEMBLING YOUR TurfVent SeriesTwo 32, 40 or 48 You will need the following tools to properly assemble your TurfVent: 2 (two) 9/16 wrenches or sockets 2 (two) 3/4 wrenches or sockets 2 (two) 15/16 wrenches or sockets 1 (one) adjustable wrench would be handy 1 accurate square, such as a framing square Grease gun and general purpose grease Carefully unpack the contents of both shipping cartons and verify that you have all the components identified on the exploded parts diagrams and parts list. Place the components in an area that provides you with enough space to fit the components together safely. Keep contents of the two boxes separate until it is time to assemble components to the frame assembly. TurfVent SeriesTwo Core Plug Aerator with Drawbar and Wheel ASSEMBLY TV 32-W Part #3232 (contains 1 box Frame Assembly #3779 & 1 box Drawbar Assembly #3782) TV 40-W Part #3240 (contains 1 box Frame Assembly #3780 & 1 box Drawbar Assembly #3782) TV 48-W Part #3248 (contains 1 box Frame Assembly #3781 & 1 box Drawbar Assembly #3782) TurfVent Series Two Core Plug Aerator with 3 - Point Hitch TV 32 H Part #3332 (contains 1 box Frame Assembly #3779 & 1 box 3pt Hitch Assembly #3783) TV 40 H Part #3340 (contains 1 box Frame Assembly #3780 & 1 box 3pt Hitch Assembly #3783) TV 48 H Part #3348 (contains 1 box Frame Assembly #3781 & 1 box 3pt Hitch Assembly #3783) Page 2

4 Reference Diagram No. 1 For Steps 1 thru 3) TurfVent SeriesTwo ASSEMBLY TV 32-W, TV 40-W, TV 48-W (continued) 1. Lay out the four frame sections. Be sure the shorter (side) sections are beneath the longer (front rear) sections. From the top, put a 3/8-16 x 1 hex capscrew into each of the four corners of the frame and hand tighten the 3/8-16 Nylon insert lock nut. Tighten the four lock nuts until the frame sections are just snug. 2. Place the frame weight grill across the opening on the bottom of the frame between the front/rear frame sections. Place the four frame weight supports (Ref. No. 3.) on the grill, lining up the holes with the frame except the center holes, which are used by the drawbar. Special Note for TV 48-W: There are two frame support and brace components that are to be placed in the holes closest to the center holes. There will then be six frame/weight supports to be attached to this model. From the top, put a 3/8-16 x 1 hex capscrew into each of the holes of the frame/weight supports and hand tighten the 3/8-16 Nylon insert lock nut on the bottom of the frame. Using your square to make sure the frame is square. Re-check the frame, making sure it is as square as possible. Tighten the lock nuts securing the frame/weight supports. Verify that it has remained square after tightening the lock nuts and adjust if necessary. 3. Line up holes in the drawbar with the center holes in the frame and put a 3/8-16 x 2-1/4 hex capscrew into each of the two center holes of the frame and through the drawbar. Put a 3/8-16 Nylon insert lock nut on the capscrews and tighten securely. Page 3

5 4. (Reference Diagram No. 2. For Step 4) Assemble the hitch plates as shown with the drawbar between them. Put two 3/8-16 x 2-1/4 hex Capscrews through this assembly from the top and tighten the 3/8-16 Nylon insert lock nuts securely.. **(Reference Diagram No. 3. For Steps 5 thru 10) 5. With the drawbar in place, the front and rear of the TurfVent is now established as well as the direction of travel. The left and right side of the TurfVent is determined by the forward direction of travel. Look carefully at the core tine cluster and shaft assembly and find an arrow sticker on one of the tine plates that indicates the direction the tines should rotate. When the aerator is attached to a tractor and in use, the tines will penetrate the ground with the closed portion facing the direction of travel. Page 4

6 6. Place the side plate assemblies on each end of the core tine shaft, resting them on the flat surface of the side plate. Remove the vinyl shipping caps from the ends of shaft and carefully place the ends of the shaft into the bearing portion of the side plates. The core tine cluster and shaft assembly should now be resting only on the bearings in the side plates. 7. Place the four 1/2-13 x 1-1/4 hex capscrew into the side frame holes from the top of the frame and lower the core tine cluster and shaft assembly on to the frame, guiding the capscrews through the appropriate holes in the side plates. Put the 1/2-13 Nylon insert lock nuts on the capscrews and tighten securely. TurfVent SeriesTwo ASSEMBLY TV 32-W, TV 40-W, TV 48-W (continued) 8. Put a 5/8 ID flat washer over the end of a 5/8-11 x 4-1/2 hex capscrew and put the capscrew through the valve stem side of a wheel and tire assembly. Put another 5/8 ID flat washer over the end of the capscrew and into the large hole on the bottom of the wheel position lever. Tighten a 5/8-11 Nylon insert lock nut until the wheel just begins to bind and then back off slightly, allowing the wheel to turn freely without excess play. Repeat for both tire assemblies. 9. Add grease to all appropriate fittings on the tine clusters and tire assemblies. Wipe off any excess grease. 10. Lift the wheel position clips and move the wheel position lever until the clip captures the shoulder bolt, holding the wheels in the transport position. OPERATING YOUR TURFVENT 32-W, 40-W, 48-W 1. Connect your TurfVent to your tractor using an appropriate hitch pin through the hitch plates and tractor platform. 2. Place the correct amount of weight into the weight tray of your aerator frame, but DO NOT EXCEED the following maximums for the TurfVent model you have: Model TV 32-W TV 40-W TV 48-W Recommended Weight pounds pounds pounds Make certain the weight is secure so it will not shift when you move around your lawn. The amount of weight needed will vary with soil conditions. 3. Drive your tractor to the lawn area you wish to aerate. When the TurfVent s wheels are on the lawn, lift the end of the wheel position clip, releasing it from the shoulder bolt, and rotate the top of the wheel position lever to the rear. This will cause the wheel to rotate forward and lower the tines to the ground. Position the other wheel in the same manner. Page 5

7 4. The TurfVent Ejector Tines have a maximum coring depth of 3.5. The moisture content of the soil, the amount of weight in the weight tray, and the travel speed all affect the turf penetration. Moist or sandy soil conditions, maximum weight, and slow travel speed will provide the maximum coring depth. OPERATION CAUTIONS AND SUGGESTIONS WARNING! Under NO circumstances should children, adults or animals be allowed on any part of the TurfVent at any time for any reason! Do not operate the TurfVent near people or pets and stop the tractor if they approach you while you are operating the TurfVent. Hitch adjustments or weights on the aerator frame should not be adjusted or moved unless the tractor is stopped and the parking brake applied. Attach the TurfVent to your tractor and detach it from your tractor ONLY when both are on level ground. Do not pull the TurfVent across a slope or incline. Always pull it straight up or straight down a slope or incline. Do not allow the TurfVent to be pulled across paved or gravel roads, driveways, sidewalks, patios, etc., as the TurfVent tines will be damaged and the surface could also be damaged. Always raise the TurfVent to the transport position when you cross these surfaces. Do not pull the TurfVent over hoses, electrical cords, down-spout extensions, etc., as damage may occur. Make certain the lawn area to be aerated is clear of these and any other obstructions before you begin using the TurfVent. The TurfVent is NOT intended for highway travel. MAINTENANCE Lubricate the tine clusters at the grease fittings after every ten hours (using a general purpose grease) of operation to keep them turning freely. Check fasteners periodically to make sure they are tight. Maintain the transport tire pressure at the 30 psi maximum. Page 6

8 TurfVent SeriesTwo Core Plug Aerator, with Drawbar and Wheel Assemblies TurfVent Model Designation TV 32-W TV 40-W TV 48-W TurfVent Part Number Working Coring Width Tine to Tine Width Overall Maximum Width Overall Length 55 ½ Maximum Coring Depth Coring Density Vents Per Square Yard Net Weight 76 lb. 84 lb. 96 lb. Shipping Weight 89 lb. 97 lb. 106 lb. MAXIMUM Weight in Tray 150 lb. 175 lb. 200 lb. Dimensions Inside Tray Width Length 31 ½ 39 ½ 47 ½ Replacement TurfVent Ejector Tine Set Part Number: COMMON SPECIFICATIONS TV 32-W TV 40-W TV 48-W TurfVent Semi Closed Core Plug Tines Heat-treated and Tempered for Lasting Performance, Allows Easier Turf Penetration and Faster Ground Speed Tine Clusters Independent Turning with Oil Impregnated Bearings, Grease Fitting Provided on Each Cluster for Periodic Lubrication, Easy to Replace TurfVent Core Plug Tines Frame Construction 1 1/2 Angle Iron, All Brackets are 10 gauge H.R. Steel Drawbar 1-1/4 Square Steel Weight Tray Galvanized Expanded Metal Wheel Adjustment Levers 1 Square Steel with Yellow Industrial Grade Vinyl Grips Wheels Painted Steel with Oilite Bushing, 410/350 x 4 2-ply Tubeless Pneumatic Tires, 30 psi All Hardware Grade 5, Capscrews with Nylon Insert Lock Nuts Page 7

9 TurfVent SeriesTwo Core Plug Aerator FRAME ASSEMBLY OPERATING Manual and PARTS Guide Quantity Supplied Ref. TV 32-W TV 40-W TV 48-W Part No. #3232 #3240 #3248 Number Description Frame Components Front/Rear Frame Front/Rear Frame Front/Rear Frame Frame Side Frame Weight Support Frame Support and Shaft Brace Frame Weight Grill Frame Weight Grill Frame Weight Grill /8-16 x 1 Hex Capscrew, Gr /8-16 Nylon Insert Lock Nut /2-13 x 1-1/4 Hex Capscrew, Gr /2-13 Nylon Insert Lock Nut Core Tine Cluster and Shaft Assembly (with end plugs for shipping) Core Tine Cluster, includes: Core Tine Tine Plate & Tube Assembly /4-20 x 1-1/2 Hex Capscrew, Gr /4-20 Nylon Insert Lock Nut Tine Plate Flat Washer, 15/16 ID Spacer Tube Tine Shaft for TV Tine Shaft for TV Tine Shaft for TV-48 Page 8

10 TurfVent SeriesTwo Core Plug Aerator WHEEL AND DRAWBAR ASSEMBLY OPERATING Manual and PARTS Guide Ref. TV 32-W TV 40-W TV 48-W Part No. #3232 #3240 #3248 Number Description Frame Components /8-16 x 2-1/4 Hex Capscrew, Gr. 5 Side Plates for Attachment to Frame Side Plate Assembly, includes: Bronze Bearing, 7/8 ID x 3/4 Drawbar Components Drawbar, 35 long Hitch Plate /8-16 x 2-1/4 Hex Capscrew, Gr /8-16 Nylon Insert Lock Nut Wheel Position Levers, Wheels, and Wheel Position Clips Wheel Position Lever Lever End Cap (included) Wheel w/410/350x4 Pneumatic Tires /8-16 x 1-3/4 Hex Capscrew, Gr /8-16 Nylon Insert Lock Nut /2 x 1-15/16 Shoulder Bolt /2-13 x 2-1/2 Hex Capscrew, Gr /2-13 Hex Nut /8-11 x 4-1/2 Hex Capscrew, Gr /8-11 Nylon Insert Lock Nut Flat Washer, 3/8 ID Flat Washer, 1/2 ID Flat Washer, 5/8 ID Wheel Position Clip Right Vinyl Clip Cap (included) Wheel Position Clip Left Vinyl Clip Cap (included) Page 9

11 TurfVent SeriesTwo Core Plug Aerator 3PT HITCH ASSEMBLY OPERATING Manual and PARTS Guide Ref. TV 32-W TV 40-W TV 48-W Part No. #3232 #3240 #3248 Number Description Side Plates for Attachment to Frame Side Plate Assembly, includes: Bronze Bearing, 7/8 ID x 3/4 3PT Hitch Assembly Left Upright Right Upright Upright Spacer Weight Brace Assembly Support Tube Lower Arm Assembly Flat Washer 5/8 ID Lock Nut 5/ Hex Capscrew 5/8-11 x Hex Capscrew 3/8-16 x 2 1/ Hex Capscrew 3/8-16 x 1 3/ Lock Nut 3/ Hex Capscrew 3/8-16 x Side Plate Assembly, includes: Bronze Bearing, 7/8 ID x 3/ Draw Bar (Lift Arm Pin) for Category 0 Hitch Draw Bar (Lift Arm Pin) for Category 1 Hitch Page 10

12 TurfVent SeriesTwo Core Plug Aerator 3PT HITCH ASSEMBLY Page 11

13 Page 12

14 WARRANTY INFORMATION MANUFACTURER S Limited Warranty Feldmann Engineering and Manufacturing Co., Inc. warrants theturfvent SeriesTwo core plug aerator to be made of first quality materials and workmanship and will, at its option, repair or replace any component or part thereof found to be defective in such materials and workmanship if returned to the factory, prepaid, within ninety (90) days (thirty (30) days for Commercial and/or Rental Use) of the date of purchase by the original purchaser. Inbound and outbound transportation charges are paid by purchaser. Feldmann Engineering assumes no responsibility for tine wear or damage caused by misuse, careless handling, incorrect or improper assembly, or repairs made or attempted by unauthorized persons. Feldmann Engineering reserves the right to change the design or specifications without notice and without any obligation or liability whatsoever. FILL IN THE FOLLOWING FOR YOUR FUTURE REFERENCE: Model Number Part Number ` Serial Number (located on the side of the drawbar) Date of Purchase Purchased From Feldmann Engineering and Manufacturing Co., Inc. 520 Forest Avenue Sheboygan Falls WI FAX: admin@jiffyonice.com Website: Printed in U.S.A. Page 13