OPERATING AND PARTS MANUAL

Transcription

1 OPERTING ND PRTS MNUL 600, 800 & 1000 ROW CROP SPREDERS 2018 Daltong.com E. Van Buren Lenox, Iowa % Employee Owned

2

3 TBLE OF CONTENTS TO YOU THE OWNER... 1 LIMITED WRRNTY STTEMENT... 2 NEW MCHINE CHECKOUT... 3 OPERTION ND SFETY... 4 LUBRICTION SCHEDULE... 5 LUBRICTION DETIL... 6 BOLT TORQUE CHRT... 7 MCHINE DJUSTMENT... 8 SPECIFICTIONS... 9 SPRED DJUSTMENT ND PPLICTION RTES SPRED PTTERN DETILS SPRED SETUP SPRED SETUP DISTRIBUTOR BLDE TUNING SPRED PTTERN DECL SPRED PTTERN DECL SPRED PTTERN DECL OR 60 SPRED PTTERN DECL, VRIBLE RTE FRME ND DRIVELINE PTO PTO TON XLE/HUB PRTS TON XLE/HUB PRTS TON XLE/HUB PRTS GROUND DRIVE SSEMBLY FRONT TNK SSEMBLY RER RE SSEMBLY GTE JCK SSEMBLY IDLER MOUNT, CHIN BELT DISTRIBUTOR GER BOX HYDRULIC SPINNER GER BOX TRCTOR HYDRULIC DRIVEN SPINNERS DIGITL REDOUT VRIBLE RTE CONTROL, ELECTRICL PLN VRIBLE RTE CONTROL, HYDRULIC PLN SPREDER CONSTNT VLUE CLIBRTION NUMBERS FOR VRIBLE RTE SPREDERS SCLE DETIL GTE MRKER DECL DECL LYOUT PRTS ORDERING PROCEDURE... 43

4 TO YOU, THE OWNER Your Dalton g Equipment is the most modern, up-to-date, versatile, machine available for fertilizer application. The machine is the result of many years of experience, research, development and testing of equipment for fertilizer application. It is soundly engineered and carefully built to rigid specifications. It is of rugged and simple construction, with a minimum of moving parts. However, to obtain maximum performance from your Dalton g Equipment, it is necessary to follow the instructions and safety suggestions in this manual. Each section has been carefully prepared for the purpose of providing needed and valuable information to the owner and operator. Each operator of this unit should be familiar with the contents of this manual. Keep it in a safe and convenient location. THERE RE MNY SFETY SUGGESTIONS (CUTION RES) PRINTED THROUGHOUT THIS MNUL. CREFULLY RED THEM LL BEFORE OPERTING THIS UNIT. DESIGN IMPROVEMENTS Dalton g Products follows a policy of continuous products improvement. We therefore reserve the right to make design improvements, and changes in specifications and prices, without incurring obligations to make revisions or additions to equipment previously sold. REGISTER WRRNTY ONE OF FOUR WYS Register on-line at: Fax your completed warranty registration form to: your completed warranty registration form to: office@daltonag.com Mail your completed warranty registration form to: Dalton g, Inc. P.O. Box 70 Lenox, I

5 LIMITED WRRNTY STTEMENT DLTON G, INC. warrants to the original purchaser only that all products manufactured under the Dalton g and Mobility Brands will be free from defects in material and workmanship under normal use and service. DLTON G s obligation under this warranty is limited to repairing or replacing, as it may elect, free of charge and without charge for installation, at the place of business of a dealer or distributor authorized to handle the equipment covered by this warranty or at a DLTON G facility, any parts that prove, in DLTON G's judgment, to be defective in material or workmanship within two (2) years after delivery to the original purchaser. DLTON G shall not be liable for personal injuries or any special or consequential damages of any kind, either direct or indirect. This warranty is subject to acts of God, fire and existing conditions of supply and demand, production, ability or inability to deliver, or for any other valid reason beyond the reasonable control of DLTON G. No distributor, dealer, agent or DLTON G employee (other than DLTON's President in writing) is authorized to extend or make any other or further express or implied warranty or incur any additional obligation on DLTON G s behalf in connection with the sale of this product. Customer Responsibility Product Registration - It is a condition of this warranty that the original purchaser fill out the warranty card furnished by DLTON G and return it to DLTON G to be recorded in DLTON G s owner file. Registration may also be done on line at If the original purchaser's card or electronic registration is not on file at DLTON G s office, the warranty period will extend only from date equipment was picked up or shipped from the DLTON G plant. Maintenance - It is the customer s responsibility to maintain their equipment in accordance with the instructions provided in the Operator s Manual. DLTON G recommends that you keep records and receipts as the customer may be required to verify the maintenance instructions have been followed. Operation It is the customer s responsibility to operate the equipment only for the purpose for which it was designed and in accordance with all safety and operational recommendations contained in the Operator's Manual. If a defect in materials or workmanship occurs, it is the customer s responsibility to cease operating the equipment until authorized repairs are made. Damage incurred from continued operation after a defect is discovered may not be covered by this warranty. What this Warranty Covers This warranty covers failures caused by defects in materials or workmanship only. This Warranty does not cover failures caused by: - Improper operation - Natural calamities - Unauthorized modifications - Unauthorized repairs - Use of Non DLTON G parts - Neglected maintenance This Warranty does not cover replacement of Wear or Maintenance Items including, but not limited to: - Lubricants - Hoses - Disks - Idlers - Filters - Tires - Chains - Blades This Warranty does not cover: Pickup and delivery of the equipment Service Calls or Travel Time to and from sites Rental of replacement equipment during repair period Products that have been declared a total loss and subsequently salvaged Overtime labor charges - Usage contrary to the intended purpose of the product - Belts - Bearings Parts Warranty DLTON G warrants its replacement parts against defects in materials or workmanship for a period of 90 days or the remainder of the product warranty, whichever is longer under the terms set out above. Remedy for defective replacement parts for units that are beyond the original product warranty, will be limited to replacement of the failed part. Daltong.com 602 E. Van Buren Lenox, Iowa PHONE: % Employee Owned FX:

6 NEW MCHINE CHECKOUT Before attempting to use or operate the spreader it is important to be thoroughly familiarized with the contents of this manual. Then the machine should be checked using the following check list: 1. Ground drive tire inflated to 22 PSI. Tires inflated to manufacturing specifications. 2. ll bearings lubricated and tightly mounted with collars securely locked. (See lubrication schedule page 5.) 3. Conveyor chains, drive chain & ground drive chain adjusted to correct tension. Conveyor chain should be flush or just below the bottom of the trough in the area approximately 2 behind the front roller. 4. Sprockets tightened & in proper alignment. 5. Inspect entire machine for loose bolts, especially in the spinner assembly and drive line area. 6. Distributor fan blades set properly. (See spread adjustment and application rates) 7. Setting of metering gate. With the pointer on the number 1 of the spread rate chart decal, the lower edge of the metering gate should be 1 ¼ above the trough floor. 8. Tighten wheel bolts daily 95 foot pounds single axle spreaders. 9. Check drive line for ease of operation by turning shaft by hand. If the foregoing inspection reveals that additional lubrication or adjustment is required, refer to the proper section of this manual for detailed instructions. 10. Ground drive wheel and universal joint shear pins in place and tight. 11. Check both spinner gear boxes for oil; fill to level of pipe plug with SE No. 90 non-detergent oil. 3

7 OPERTION SPREDER SFETY Before starting in motion please read the following words of caution.. It is recommended that initial spreading be done in as low a range as possible to permit easy break-in. B. lways shut off or disconnect power to spreader before attempting to repair or adjust the spreader. C. Do not transport machine with ground drive wheel engaged. D. NEVER back-up spreader with ground drive wheel engaged. E. Make sure that the towing vehicle brakes are operating properly and are capable of stopping the towing vehicle. F. If a pick-up is used as the towing vehicle, it is wise to add ballast for additional safety and traction. We recommend that all towing vehicles be ballast loaded to their recommended G.V.W. G. Hitches should be of heavy construction and should be welded or bolted directly to the towing vehicle frame. Hitches should be checked routinely for loose bolts, cracked welds, etc. H. Never tow a spreader with a drawbar pin less than 1 in diameter. Pins should also have a locking device. I. Do not tow spreader at speeds in excess of 20 mph loaded or 40 mph empty. J. Remember, that the stopping and braking distances vary with load and vehicle speed. It is well to familiarize yourself with the characteristics of your machine under different load and speed conditions. K. Be sure to attach safety break-away chain and the safety chain to towing vehicle to assure control of spreader in the case of pin or hitch failure. L. The unit is designed for hitching to vehicles with drawbar heights between 12 and 18 inches above the ground level. It will operate with all standard tractor hitches and PTO s. WRNING: Hydraulically mounted drawbars must be securely and mechanically locked because a fully loaded spreader applies a load in the order of 2000 lbs. to the hitch. M. WRNING: Remember this unit is designed for agricultural use only and is primarily an off-the-road vehicle and should be towed at tractor speeds ONLY, not to exceed 20 mph loaded or 40 mph empty. Inspect hubs routinely to see if they are heating, which indicates either a need for lubrication or improper adjustment of brakes or bearings, also check stud nuts for tightness. N. WRNING: The maximum capacity of this unit is 6 tons (600) or 200 cubic feet, based on a material density of 60 pounds per cubic foot. DO NOT EXCEED THIS LIMIT! OPERTING INSTRUCTIONS Please read the following completely before spreading. 1) ttach spreader to towing vehicle, make sure hitch and hitch pin are sound. 2) ttach PTO shaft to proper rpm PTO. 3) Spinner discs, adjustable chute and conveyor floor should be clean for accurate metering. 4) Set metering gate to desired spread rate according to decal on the back end sheet of tank. lways keep the machine in the lowest possible range. 5) Before starting to spread, rotate the ground drive wheel several revolutions by hand to make sure the conveyor chain is operating freely. If chain is frozen or moves with too much resistance, correct problem before using spreader. 6) If the ground drive wheel operates properly, check with chain and sprocket arrangement for desired range setting and chain tension. 7) When spreading is complete, disengage ground drive assembly from the tire and install transport lockup. 4

8 LUBRICTION SCHEDULE LL MODELS (4) BERINGS (2) U-JOINTS DRIVELINE (1) BERING GROUND DRIVE (4) U-JOINTS (2) TELESCOPING TUBES DILY LUBRICTION SCHEDULE CONVEYOR DRIVE LL MODELS (6) BERINGS (2) SHFT HOUSINGS GROUND DRIVE LL MODELS (2) U-JOINTS TELESCOPING TUBE (2) SQUIRTS OF SE 90 OIL INTO JCK CRNK OIL CP Pay particular attention to the daily cleaning and greasing of the telescoping tube assembly. WEEKLY LUBRICTION SCHEDULE CHINS OIL LUBRICTE PIN JOINTS WITH SE PTO SHFT GRESE (2) U-JOINTS ND SLIP TUBE SPINNER GERBOX GRESE UNIVERSL GRESE ON ECH FITTING UNDER SPINNER HUB MONTHLY LUBRICTION SCHEDULE DRIVE SHFT SPLINES SPINNER GER BOX COT WITH GRESE OR NTI-SEIZE COMPOUND CHECK TO SEE THT OIL LEVEL IS UP TO OIL LEVEL PLUG. USE SE 90 OIL NNUL LUBRICTION SCHEDULE WHEEL BERINGS GER BOXES REPCK DRIN, FLUSH, ND REFILL WITH SE 90 OIL MINTENNCE SCHEDULE WEEKLY WSH SPREDER CHECK GROUND DRIVE TIRE INFLTION (22 PSI) CORRECT BELT TENSION DJUST TENSION OF CONVEYOUR ND DRIVE CHINS (SEE MCHINE CHECKOUT) SEMI-NNULLY TIGHTEN LOOSE BOLTS REPLCE WORN OR FILED PRTS TOUCH-UP PINT 5

9 LUBRICTION DETIL DETIL SCLE 4 : DRWN BY CHECKED BY PRINT DTE RICH SMOTHERS CONFIG. Default PROPRIETRY ND CONFIDENTIL COMMENTS: THE INFORMTION CONTINED IN THIS DRWING IS THE SOLE PROPERTY OF DLTON G. NY REPRODUCTION IN PRT OR S WHOLE WITHOUT THE WRITTEN PERMISSION OF DLTON G IS PROHIBITED. F O R P R T S, C L L /28/ /9/2010 LUBRICTION SCHEDULE 1 SLIP JOINT DILY 2 PIVOT BUSHING EVERY 10 HRS 3 UNIVERSL JOINT EVERY 15 HRS 4 BLL BERING EVERY 15 HRS 5 CTUTOR EVERY 15 HRS 6 SPINNER HUB EVERY 15 HRS 7 GER BOX EVERY 75 HRS 8 GTE JCK (OIL) WEEKLY 9 WHEEL BERING TWICE YER DWG: SIZE SHEET TITLE: REV SCLE: 1:26 w w w. D a l t o n g. c o m LUBRICTION SCHEDULE Sheet1 SHEET 1 OF 1

10 IMPORTNT : Over tightening hardware can be as damaging as under tightening. Tightening beyond recommended torque will reduce the fastener s shock load capacity. WRNING: Never work around any raised implement while in the raised position without using safety lockups. 7

11 MCHINE DJUSTMENT WHEEL BERING DJUSTMENT fter repacking or when inspecting wheel bearings, the following adjustment procedure should be followed. Place flat washer and spindle nut on spindle. Turn hub as you tighten nut. When a pronounced drag is felt in the bearings, back off nut one complete slot. If necessary continue to back off the nut until the next slot aligns with the cotter pin hole and install cotter pin and dust cap. CONVEYOR CHIN DJUSTMENT Loosen chain take-up locking nuts on outside of front end of trough. djust take-up bolts evenly until chain clears main frame members and axle tube by ¾ ½. Inspect shaft bearing mounting bolts and shaft locking collars for tightness of set screws (6 places). Reset take-up locking nuts. STORGE Before storing the spreader for more than a few days, the machine should be emptied completely and thoroughly washed both inside and out. This precaution will minimize the severity of fertilizer acid corrosion, extend the useful life of the machine, and prevent damage to drive line and conveyor chain from fertilizer compaction and caking. We further recommend that the machine be thoroughly greased after washing. Before operating the machine after extended periods of storage, re-lubricate the entire spreader in accordance with the lubrication section of this manual. lso check the entire spreader, following the New Machine Checkout Procedure to be found in a foregoing section of the manual. Remember that oil and grease are your least expensive corrosion inhibitors. DDITIONL INSTRUCTIONS: CUTION Do not operate your spreader with less than one and a half (1 1/2) inch of metering gate opening as material will compact against metering gate and cause failure of the conveyor chain. CUTION Do not disconnect implement from tractor with material remaining in box. 8

12 SPECIFICTIONS Capacity (weight) 8 tons 10 tons Hopper length 120" 148" Hopper width 93" 93" Hopper capacity (volume) 270 cu. ft. 333 cu. ft. Overall length 215" 250" Overall height 120" 120" Overall width 136" 136" Empty weight 4,900 lbs 5,900 lbs Ground clearance 44" under spinners 37" under frame 44" under spinners 37" under frame Spread pattern 40', 50', 60' 40', 50', 60' Hopper construction 409 stainless 409 stainless Hub & spindle rating 15,000 lbs. ea. 22,500 lbs. ea. PTO drive 540 rpm or 1000 rpm N/ Conveyor trough Stainless Steel Stainless Steel Jack 5,000 lbs 5,000 lbs xle 80"-120" adjustable 80"-120" adjustable Drive chains Spreading width, average material #40 Ground Drive & #50 Conveyor Drive 66 TO 1,500 lbs. per acre at 9 MPH, OR 1,200 lbs. per min. #40 Ground Drive & #50 Conveyor Drive 66 TO 1,500 lbs. per acre at 9 MPH, OR 1,200 lbs. per min. Spindle diameter 3.5" 4.5" Conveyor drive 2-Speed or Hyd Hyd Gate jack Screw-type Screw-type Tires and wheels 380/90/R46 380/90/R46 Duals Optional 9

13 SPRED DJUSTMENT ND PPLICTION RTES For accurate and precise spreading rates, it is necessary that you know the weight in pounds per cubic foot of the material to be spread. If this is not known, the weight can be quickly and accurately determined by the following method: 1. Weigh an empty one gallon container. 2. Fill level full with the material to be used. 3. Weigh container and material, and then subtract the weight of the container to obtain the weight of the material. 4. Multiply the weight of the material by 7.5 to obtain the weight of the material in pounds per cubic foot. Example: Typical Material-Potash 1) Weight of empty one gallon container 1.00 lbs. 2) Weight of filled container lbs. 3) Weight of container (net) 9.35 lbs. 4) 9.35 X lbs. /cu ft. You would therefore use the column on the Spread Chart headed 70 to determine the proper gate opening for the desired application rate. Your Mobility Spreader with its heavy-duty distributor discs and blades will apply most materials in a 50 foot wide swath. 10

14 SPRED PTTERN DETILS n operational characteristic of this type of machine is the possibility of overloading the distributors at high rates of application. Such an overload results in an alteration of the spread pattern to a narrower swath with heavier application at the center. This can be avoided by reducing speed when using high application rates. MOBILITY DISTRIBUTORS RE DESIGNED FOR MXIMUM PPLICTION RTE OF 1500 POUNDS PER MINUTE OF VERGE 60 POUND PER CUBIC FOOT MTERIL. Caution: Be extra careful to check your spread pattern when using high application rates. djust your driving pattern to the actual delivered spread swath, the adjustment of the machine, and the material being used. Recommended ground or travel speed for most application rates (up to 700 pounds per acre) is 8 mph. When application rates are in excess of 700 pounds per acre, the ground speed should be proportionately reduced, (for example, at 1400 pounds per acre, maximum ground speed should be 4 mph.) We recommend that for very high application rates, to insure uniformity of application, that two lighter application passes be made preferably placing your second pass over the lap lines of the first pass. This also is recommended practice when spreading under very windy conditions or with a material that segregates easily. If your effective spread pattern is more than 50 feet wide the Metering Gate setting should be increased proportionately, according to the percentage of your spread width in excess of 50 feet. The gate setting should likewise be decreased if your effective spread pattern is less than 50 feet. EXMPLE: 60 foot effective spread width increase gate setting from Spread Chart by 20%; 40 foot effective spread pattern width decrease your gate setting from Spread Chart setting by 20%. Your spread pattern can be checked accurately and visually on a freshly worked, level area of ground. Such an area is also ideally suited to adjusting and fine tuning your machine. The following diagram graphically illustrates a typical spread pattern. Note on the illustration below that the lap point occurs at the point where the application rate is one-half of the spread chart rate. The profile of the spread pattern tapers at both edges and has a wide uniform area in the center. By careful attention to the lap point during application, a very uniform and even spread rate can be attained. The Mobility Spreaders have been designed to provide this good and uniform tapered profile to make spread width less critical. However, excessive or insufficient overlap of passes will result in a poor application pattern in the lap area of the total spread pattern. If you can attain this spread pattern and pay careful attention to the lap points, the dotted line on the illustration will represent your actual overall spread pattern. 11

15 50 SPRED SETUP # PRT NUMBER QTY DISTRIBUTOR DISC 2 2 MS EXTR LONG DISTRIBUTOR BLDE, 8, RIGHT 1 3 MS EXTR LONG DISTRIBUTOR BLDE, 8, LEFT 1 4 MS INCH DISTRIBUTOR BLDE, RIGHT 1 5 MS INCH DISTRIBUTOR BLDE, LEFT 1 6 MS DISTRIBUTOR BLDE, RIGHT 1 7 MS DISTRIBUTOR BLDE, LEFT 1 8 MS DISTRIBUTOR BLDE, 5.5, RIGHT 1 9 MS DISTRIBUTOR BLDE, 5.5, LEFT 1 50 FT SPRED SET UP ROTTION ROTTION VIEWED FROM BCK OF SPREDER PROPRIETRY ND CONFIDENTIL THE INFORMTION CONTINED IN THIS DRWING IS THE SOLE PROPERTY OF DLTON G. NY REPRODUCTION IN PRT OR S WHOLE WITHOUT THE WRITTEN PERMISSION OF DLTON G IS PROHIBITED. DRWN BY CHECKED BY PRINT DTE RICH SMOTHERS 4/17/2017 CONFIG. STNDRD SPRED PTERN, BLDE SETUP COMMENTS: F O R P R T S, C L L /16/2013 w w w. D a l t o n g. c o m DWG: 50 FT SPRED SET UP SIZE SHEET TITLE: SCLE: 1:6 Sheet1 SHEET 1 OF 1 REV 12

16 60 SPRED SETUP # PRT NUMBER QTY DISTRIBUTOR DISC 2 2 MS EXTR LONG DISTRIBUTOR BLDE, 8, RIGHT 1 3 MS EXTR LONG DISTRIBUTOR BLDE, 8, LEFT 1 4 MS INCH DISTRIBUTOR BLDE, RIGHT 1 5 MS INCH DISTRIBUTOR BLDE, LEFT 1 6 MS DISTRIBUTOR BLDE, RIGHT 1 7 MS DISTRIBUTOR BLDE, LEFT 1 8 MS DISTRIBUTOR BLDE, 5.5, RIGHT 1 9 MS DISTRIBUTOR BLDE, 5.5, LEFT 1 60 FT SPRED SET UP ROTTION 4 ROTTION VIEWED FROM BCK OF SPREDER PROPRIETRY ND CONFIDENTIL THE INFORMTION CONTINED IN THIS DRWING IS THE SOLE PROPERTY OF DLTON G. NY REPRODUCTION IN PRT OR S WHOLE WITHOUT THE WRITTEN PERMISSION OF DLTON G IS PROHIBITED. DRWN BY CHECKED BY PRINT DTE RICH SMOTHERS 4/17/2017 CONFIG. 60 FT SPRED PTTERN, BLDE SETUP COMMENTS: F O R P R T S, C L L /16/2013 w w w. D a l t o n g. c o m DWG: 60 FT SPRED SET UP SIZE SHEET TITLE: SCLE: 1:6 Sheet1 SHEET 1 OF 1 REV 13

17 DISTRIBUTOR BLDE TUNING FINE TUNING OF DISTRIBUTOR ND BLDE SETTINGS ll Mobility Spreaders are given an average standard factory setting of distributor blades. Such a setting, of course, cannot be perfect for all field conditions and materials. The following information will be helpful in adjusting the distributor blades on your machine to give optimum performance for your specific conditions. Your spread pattern will be affected by 1) the material used, 2) the distributor blade setting, and 3) the rotation speed of the distributors. The distributors are designed to be operated at 750 RPM (540 tractor P.T.O. RPM). plus or minus 10% change in distributor RPM will increase or decrease spread pattern width accordingly. n increase in PTO RPM will tend to deposit less material at the center of the spread pattern, while a decrease will deposit more material at the center. The physical characteristics of the materials being spread, which are important to the spread pattern, include bulk density, particle size, particle shape, physical strength and rugosity or surface roughness. For best performance it is recommended that you fine tune your machine to the material being used. The spreading profile and spread swath width can be changed drastically by alteration of the setting of the distributor blades. The drawing on the next page shows had blades may be extended from or retracted toward the center of the disc. lso, the angle of blade intersection with a radius of the disc may be altered. They may be advanced toward coincidence with the disc radius or retarded away from it. Further, blade lengths are not all equal. These adjustments affect the spread pattern in the following ways: 1. dvance long blades--more material to the outside of spread pattern; also will increase spread pattern width. 2. Retard long blades--opposite effect of above. 3. dvance short blades helps eliminate problem of streaking in the middle of spread pattern. 4. Retard short blades puts more material in the center of spread pattern. 5. Extend blades away from center of spinner increases spread width somewhat. 6. Retract blades (more towards center of spinner) opposite effect of above. 7. Moving flow divider (or chute) toward the front of spreader will tend to put more material in center of spread pattern. This is because material is deposited on outer edge of spinner causing it to leave earlier. 8. Moving divider toward the rear of the spreader has the opposite effect. DISTRIBUTOR BLDE TUNING, MOBILITY EXTENDED BLDE RETRCTED BLDE DVNCED BLDE RETRDED BLDE ROTTION 14 ROTTION

18 40 SPRED LOW RNGE 12 TO 72 T. GTE OPENING GTE OPENING NOTICE PPROXIMTELY 40 FT. SPRED MTERIL WEIGHT IN POUNDS PER CUBIC FOOT HIGH RNGE 24 TO 48 T. MTERIL WEIGHT IN POUNDS PER CUBIC FOOT PPLICTION RTE EXPRESSED IN POUNDS PER CRE PRT NO

19 50 SPRED LOW RNGE 12 TO 72 T. GTE OPENING GTE OPENING NOTICE PPROXIMTELY 50 FT. SPRED MTERIL WEIGHT IN POUNDS PER CUBIC FOOT HIGH RNGE 24 TO 48 T. MTERIL WEIGHT IN POUNDS PER CUBIC FOOT PPLICTION RTE EXPRESSED IN POUNDS PER CRE PRT NO

20 60 SPRED LOW RNGE 12 TO 72 T. GTE OPENING GTE OPENING NOTICE PPROXIMTELY 60 FT. SPRED MTERIL WEIGHT IN POUNDS PER CUBIC FOOT HIGH RNGE 24 TO 48 T. MTERIL WEIGHT IN POUNDS PER CUBIC FOOT PPLICTION RTE EXPRESSED IN POUNDS PER CRE PRT NO

21 50 or 60 SPRED, VRIBLE RTE 18

22 FRME ND DRIVELINE REVISIONS 21 REV. DESCRIPTION DTE PPROVED STNDRD: HD CLEVIS BOLT, 1" X 7" NUT, 1" CENTERLOCK OPTIONL: BULL PULL HITCH, CT BULL PULL PIN # PRT NUMBER Q 1 6 TON & 8 TON FRME BOLT,.375 NC x 1.25, PLTD BOLT,.375 NC x 1.5, G5, PLTD PILLOW BLOCK BERING SHFT BERING RM, FRONT SPLIT POLY BERING & HOUSING SPLIT POLY INSERT ONLY SHIELD, MOUNTING BRCKET, RH SHIELD, MOUNTING BRCKET, LH FLT WSHER,.375 SS FLT WSHER,.375 SS NUT,.375 NC SS SHFT, FRONT, 1x133, 8TON PULLEY, 4.75 DI FOR 1000 PTO 1 PROPRIETRY ND CONFIDENTIL THE INFORMTION CONTINED IN THIS DRWING IS THE SOLE PROPERTY OF DLTON G. NY REPRODUCTION IN PRT OR S WHOLE WITHOUT THE WRITTEN PERMISSION OF DLTON G IS PROHIBITED. HITCH: BOLT ON DRWN BY RICH SMOTHERS 1/15/2013 CHECKED BY PRINT DTE 5/2/2017 CONFIG. FRME & DRIVELINE ROW CROP COMMENTS: F O R P R T S, C L L # PRT NUMBER Q PULLEY, 6.75 DI FOR 540 PTO PULLEY, 8.25 DI FOR 1000 PTO PULLEY, 6.25 DI FOR 540 PTO PTO COMPLETE, N RPM PTO HLF SHFT BELT U-JOINT, DRIVE SHFT SHFT, BCK, 1 x 21, 8 TON PTO SHIELD TLL 5000 LBS JCK CRRIGE BOLT,.4375 x SPRING LOCK NUT, HD HITCH CLEVIS 1 28B BULL PULL HITCH, CT LOCK WSHER,.375 STD SS 54 w w w. D a l t o n g. c o m DWG: FRME & DRIVELINE ROW CROPS SIZE SHEET TITLE: 6 ND 8 TON ROW CROP SCLE: 1:32 SHEET 1 OF 1 REV 19

23 540 PTO PTO COMPLETE, N PTO HLF 12 N FEMLE, IMPLEMENT W SHIELD PTO SHEILD KIT PTO SHIELD ONLY, INNER w RETINER PTO SHIELD ONLY, OUTER w RETINER RETINER KIT, 12N PTO HLF, MLE TRCTOR HLF W SHIELD REPIR KIT, U-JOINT, 12N LOCK PIN REPIR KIT DRWN BY CHECKED BY PRINT DTE RICH SMOTHERS 7/28/2014 CONFIG. Default PROPRIETRY ND CONFIDENTIL COMMENTS: THE INFORMTION CONTINED IN THIS DRWING IS THE SOLE PROPERTY OF DLTON G. NY REPRODUCTION IN PRT OR S WHOLE WITHOUT THE WRITTEN PERMISSION OF DLTON G IS PROHIBITED. F O R P R T S, C L L /7/2014 w w w. D a l t o n g. c o m DWG: RPM PTO SHFT OPTION SIZE SHEET TITLE: Sheet1 REV SCLE: 1:10 SHEET 1 OF 1 20

24 1000 PTO RPM PTO SHFT RPM PTO SHFT PTO HLF 12 N FEMLE, IMPLEMENT W SHIELD PTO SHIELD KIT PTO SHIELD ONLY, INNER w RETINER PTO SHIELD ONLY, OUTER w RETINER RETINER KIT, 12N PTO HLF, MLE, TRCTOR REPIR KIT, U-JOINT, 12N PTO KIT, SNP HITCH 1000 RPM DRWN BY CHECKED BY PRINT DTE RICH SMOTHERS 12/24/2015 CONFIG. Default PROPRIETRY ND CONFIDENTIL COMMENTS: THE INFORMTION CONTINED IN THIS DRWING IS THE SOLE PROPERTY OF CMC-DLTON G. NY REPRODUCTION IN PRT OR S WHOLE WITHOUT THE WRITTEN PERMISSION OF CMC-DLTON G IS PROHIBITED. F O R P R T S, C L L /7/2014 w w w. D a l t o n g. c o m DWG: RPM PTO SHFT SIZE SHEET TITLE: Sheet1 REV SCLE: 1:10 SHEET 1 OF 1 21

25 6 TON DJUSTBLE XLE & HUB PRTS 6 TON DJUSTBLE XLE & HUB PRTS CENTER DJ XLE CLMP , BOLT.625X9.5 NC FLT WSHER, OUTSIDE DJ XLE CLMP LOCK WSHER, NUT,.625 NC, PLTD DJUSTBLE XLE, 6 TON ROW CROP DJUSTBLE XLE, 6 TON ROW CROP, GROUND DRIVE DJUSTBLE XLE, 6 TON ROW CROP, SCLE DJUSTBLE XLE, 6 TON ROW CROP, GROUND DRIVE, SCLE S5199-K-00-3"X16" SPINDLE , SCLE SPINDLE HUB, COMPLETE SEL SCLE SPINDLE SEL BERING RCE HUB HUB w RCES & LUGS HUB BOLT RCE RC DJ, 6 TON PROPRIETRY ND CONFIDENTIL THE INFORMTION CONTINED IN THIS DRWING IS THE SOLE PROPERTY OF DLTON G. NY REPRODUCTION IN PRT OR S WHOLE WITHOUT THE WRITTEN PERMISSION OF DLTON G IS PROHIBITED. 5 4 DRWN BY CHECKED BY PRINT DTE CONFIG. COMMENTS: RICH SMOTHERS 10/17/2017 EXPLODED XLE FOR DRWING F O R P R T S, C L L SPINDLE WSHER BERING SLOTTED NUT, FULL CSTLE NUT, 1.25, SCLE DUST CP P COTTER PIN,.1875 x 2.5 2/9/ HUB REBUILD KIT HUB REBUILD KIT 758 SCLE DWG: 602 E. VN BUREN ST., LENOX, I TON DJUSTBLE XLE & HUB PRTS SHEET TITLE: SIZE SCLE: 1:52 6 TON SHEET 1 OF 1 1 REV 22

26 8 TON DJUSTBLE XLE & HUB PRTS 8 TON DJUSTBLE XLE & HUB PRTS RC SINGLE XLE CLMP , BOLT.625X9.5 NC FLT WSHER, OUTER DJ XLE CLMP LOCK WSHER,.625, PLTD NUT,.625 NC, PLTD DJUSTBLE XLE, 8 TON ROW CROP DJUSTBLE XLE, 8 TON ROW CROP, GROUND DRIVE DJUSTBLE XLE, 8 TON ROW CROP, SCLE DJUSTBLE XLE, 8 TON ROW CROP, GROUND DRIVE, SCLE , SLEEVE INTERMEDITE S-5296-L -12 SPINDLE, 3.50X SCLE SPINDLE SEL SCLE SEL BERING HUB, COMPLETE RCE HUB HUB w RCES & LUGS RCE BERING SPINDLE WSHER COTTER PIN SLOTTED NUT, 1.25 NC CSTLE NUT, 1.25, SCLE RC DJ, 8 TON PROPRIETRY ND CONFIDENTIL THE INFORMTION CONTINED IN THIS DRWING IS THE SOLE PROPERTY OF DLTON G. NY REPRODUCTION IN PRT OR S WHOLE WITHOUT THE WRITTEN PERMISSION OF DLTON G IS PROHIBITED. DRWN BY CHECKED BY PRINT DTE CONFIG. COMMENTS: RICH SMOTHERS EXPLODED XLE PRTS 10/17/2017 F O R P R T S, C L L GSKET, DUST CP 1/15/ DUST CP BOLT,.3125 x HUB REBUILD KIT HUB REBUILD KIT 873 SCLE DWG: 8 TON DJUSTBLE XLE & HUB PRTS SHEET TITLE: SIZE SCLE: 1: E. VN BUREN ST., LENOX, I TON SHEET 1 OF 1 1 REV 23

27 10 TON DJUSTBLE XLE & HUB PRTS 10 TON DJUSTBLE XLE & HUB PRTS SSEMBLY DJUSTBLE XLE, 10 TON SLEEVE, TINTERMEDITE, SCLE KIT G281914, SPINDLE , SCLE SPINDLE HUB, COMPLETE SEL SCLE SEL BERING RCE RCE HUB G HUB W/RCES & LUGS BERING SPINDLE WSHER COTTER PIN,.375 x SLOTTED NUT, 2-12 NC DUST CP BOLT,.3125 x.75 DRWN BY CHECKED BY PRINT DTE CONFIG. COMMENTS: LLong EXPLODED XLE PRTS 11/15/ HUB REBUILD KIT 881/ HUB REBUILD KIT 881/891 SCLE 3/31/ E. VN BUREN ST., LENOX, I DWG: 10 TON DJUSTBLE XLE & HUB PRTS PROPRIETRY ND CONFIDENTIL THE INFORMTION CONTINED IN THIS DRWING IS THE SOLE PROPERTY OF DLTON G. NY REPRODUCTION IN PRT OR S WHOLE WITHOUT THE WRITTEN PERMISSION OF DLTON G IS PROHIBITED. SIZE SHEET TITLE: Sheet1 REV C:\_EPDM_Vault\Spreader\MOBILITY\ms assemblies\ SCLE: 1: SHEET 1 OF 1 24

28 GROUND DRIVE SSEMBLY (for 6 & 8 Ton only) GROUND DRIVE SSEMBLY RC RC #40 SS NUT,.25 NC, PLTD LOCK WSHER,.25 PLTD , #40 SS LINK DJUSTMENT HNDLE LOCK WSHER,.5, PLTD FLT WSHER,.5 PLTD IDLER BLOCK BOLT,.375 NC X 2, G5, PLTD FLT WSHER, DJUSTBLE LUG, GROUND DRIVE LOCK WSHER, NUT,.375 NC SS CYLINDER LOCK LOCK PIN, SQURE WIRE FEMLE DRIVE SHFT WELDMENT DRIVE SHFT, INTERMEDITE MLE DRIVE SHFT WELDMENT FLT WSHER,.25 PLTD HYDRULIC CYLINDER 2 x 4 x BOLT,.25x2.5 NC S.S SPROCKET, 12 TOOTH SPROCKET, 72 TOOTH WHEEL SSEMBLY TIRE WHEEL SPROCKET, 24 TOOTH KEY,.25 x.25 x SPROCKET, 48 TOOTH BERING, 1 INCH BORE CRRIGE BOLT,.5-13x GROUND DRIVE SHFT ROLL PIN.375x NUT,.3125 NC G8 PLTD LOCK WSHER,.3125 MED SPG PLTD BOLT,.3125x2 NC PLTD 8 TON WHEEL SHFT, GROUND DRIVE, 8 TON 6 TON WHEEL SHFT, GROUND DRIVE, 6 TON 6 TON GROUND DRIVE TOP, 6T 8 TON GROUND DRIVE TOP, 8T 5 PROPRIETRY ND CONFIDENTIL THE INFORMTION CONTINED IN THIS DRWING IS THE SOLE PROPERTY OF DLTON G. NY REPRODUCTION IN PRT OR S WHOLE WITHOUT THE WRITTEN PERMISSION OF DLTON G IS PROHIBITED. 4 DRWN BY CHECKED BY PRINT DTE CONFIG. COMMENTS: RICH SMOTHERS Default 5/15/2017 FOR USE WITH HYDRULIC CYLINDER ON/OFF F O R P R T S, C L L /13/ DWG: 602 E. VN BUREN ST., LENOX, I GROUND DRIVE SSEMBLY SHEET TITLE: 6 ND 8 TON ONLY SIZE SCLE: 1:10 SHEET 1 OF 1 1 REV 25

29 FRONT TNK SSEMBLY FRONT TNK SSEMBLY, ROW CROP SSEMBLY ROLL TRP, 93 X 120, MOBILITY 6 & 8 TON ROLL TRP, 93 X 148, MOBILITY 10 TON , CONVEYOR SHIELD, 6 & 8 TON , CONVEYOR SHIELD, 10 TON BOLT,.375 NC X 1.25, PLTD FLT WSHER,.375 SS LOCK WSHER,.375 STD SS NUT,.375 NC SS WINDOW GSKET SIGHT GLSS CONVEYOR SPLICE PIN DRG CHIN, 6 & 8 TON DRG CHIN, 10 TON BOLT, TKE UP BERING, TKE-UP FRONT ROLLER DRWN BY CHECKED BY PRINT DTE CONFIG. COMMENTS: 5/17/2017 FRONT TNK SSEMBLY, ROW CROP 5/2/2017 DWG: 602 E. VN BUREN ST., LENOX, I FRONT TNK SSEMBLY, ROW CROP PROPRIETRY ND CONFIDENTIL THE INFORMTION CONTINED IN THIS DRWING IS THE SOLE PROPERTY OF DLTON G. NY REPRODUCTION IN PRT OR S WHOLE WITHOUT THE WRITTEN PERMISSION OF DLTON G IS PROHIBITED. SIZE SHEET TITLE: 6, 8 ND 10 TON REV 5 C:\_EPDM_Vault\Spreader\MOBILITY\MS ssemblies\ SCLE: 1: SHEET 1 OF 1 26

30 RER RE SSEMBLY RER RE SSEMBLY PROPRIETRY ND CONFIDENTIL THE INFORMTION CONTINED IN THIS DRWING IS THE SOLE PROPERTY OF DLTON G. NY REPRODUCTION IN PRT OR S WHOLE WITHOUT THE WRITTEN PERMISSION OF DLTON G IS PROHIBITED. 4 DRWN BY CHECKED BY PRINT DTE CONFIG. COMMENTS: RICH SMOTHERS EXPLODED RER VIEW F O R P R T S, C L L /17/ /15/ ITEMS RE MODEL SPECIFIC DWG: 602 E. VN BUREN ST., LENOX, I RER RE SSEMBLY SIZE SHEET TITLE: SCLE: 1:18 Sheet1 SHEET 1 OF REV 27

31 RER RE SSEMBLY # PRT NUMBER Q 1 MS DIVIDER 1 2 MS DIVIDER WELDMENT WLD, FEMLE 0.5, DRIVE SHFT BUMPER WELDMENT GER BOX SET DISC CP WELDMENT R.H DISC CP WELDMENT L.H DRIVE SPROCKET SSEMBLY CST SPROCKET, MCHINED SPROCKET SHFT ROLL PIN.3125 x BERING, 1.25 BORE 2-BOLT FLNGE SPROCKET 50B SPROCKET, 50B BERING, 1 INCH BORE 2-BOLT BOLT,.375 NC x 1.5, G5, PLTD BOLT,.375 NC x 1.25, PLTD LOCK WSHER,.75, PLTD STINLESS #50 CHIN, 108 PITCH w CONNECTOR (8 TON GROUND DRIVE) STINLESS #50 CHIN, 125 PITCH w CONNECTOR (6 TON GROUND DRIVE) LINK /2 LINK (OFFSET) (6 TON) DISTRIBUTOR DISC SSEMBLY, L.H MS DISTRIBUTOR BLDE, LEFT 1 25 MS DISTRIBUTOR BLDE, 5.5, LEFT 1 26 MS INCH DISTRIBUTOR BLDE, LEFT 1 27 MS EXTR LONG DISTRIBUTOR BLDE, 8, LEFT DISTRIBUTOR DISC VR SPINNER HUB,VRIBLE RTE, MCHINED , LOCK WSHER,.3125 SS WSHER,.3125 SS BOLT,.3125 x.75 SS NUT,.3125 NC SS x1 NC SS DISTRIBUTOR DISC SSEMBLY, RH 1 36 MS INCH DISTRIBUTOR BLDE, RIGHT 1 37 MS DISTRIBUTOR BLDE, RIGHT 1 # PRT NUMBER Q 38 MS EXTR LONG DISTRIBUTOR BLDE, 8, RIGHT 1 39 MS DISTRIBUTOR BLDE, 5.5, RIGHT SPINNER HUB, STNDRD DISTRIBUTOR DISC x1 NC SS , LOCK WSHER,.3125 SS NUT,.3125 NC SS WSHER,.3125 SS KEY,.25 x.25 x NUT, NF, SS TROUGH EXTENSION BCK FLT WSHER,.375 SS LOCK WSHER,.375 STD SS NUT,.375 NC SS BOLT.375 x 1 NC SS 5 53 MS PRTER PLTE BOLT.375 x.75 NC SS x1 NC SS WSHER,.3125 SS , LOCK WSHER,.3125 SS NUT,.3125 NC SS 3 ** DISTRIBUTOR BLDE SET INCLUDES BOTH RIGHT SIDE ND LEFT SIDE BLDES. PROPRIETRY ND CONFIDENTIL THE INFORMTION CONTINED IN THIS DRWING IS THE SOLE PROPERTY OF DLTON G. NY REPRODUCTION IN PRT OR S WHOLE WITHOUT THE WRITTEN PERMISSION OF DLTON G IS PROHIBITED. DRWN BY RICH SMOTHERS CHECKED BY PRINT DTE CONFIG. COMMENTS: F O R P R T S, C L L w w w. D a l t o n g. c o m DWG: RER RE SSEMBLY SIZE SHEET TITLE: Sheet2 SCLE: 1:20 SHEET 2 OF 2 REV 28

32 GTE JCK SSEMBLY , GTE JCK SSEMBLY NUT,.375 NC SS LOCK WSHER,.375 STD SS FLT WSHER,.375 SS , JCK, METERING U-BOLT,.375X 2.25X3.5 NC, SS BRCKET, METERING JCK BOLT.375 X 1 NC SS , BOLT.375 X 3 NC SS METERING GTE WELDMENT DRWN BY CHECKED BY PRINT DTE RICH SMOTHERS 10/19/2017 CONFIG. Default PROPRIETRY ND CONFIDENTIL COMMENTS: THE INFORMTION CONTINED IN THIS DRWING IS THE SOLE PROPERTY OF DLTON G. NY REPRODUCTION IN PRT OR S WHOLE WITHOUT THE WRITTEN PERMISSION OF DLTON G IS PROHIBITED. F O R P R T S, C L L /30/2017 w w w. D a l t o n g. c o m DWG: GTE JCK SSEMBLY SIZE SHEET TITLE: Sheet1 REV SCLE: 1:4 SHEET 1 OF 1 29

33 IDLER MOUNT, CHIN BELT IDLER MOUNT, CHIN BELT , VRIBLE RTE CHIN LINK , 1/2 LINK (OFFSET) NUT,.5 NC, LOCKING, PLTD FLT WSHER, SPROCKET, 50B-13.5 BORE, IDLER , DOM 1 X.25 X , GUSSET, VR MOUNT BOLT.5 NC X 3, G5 DRWN BY CHECKED BY PRINT DTE CONFIG. COMMENTS: LLong Default 5/15/2017 3/30/2017 DWG: 602 E. VN BUREN ST., LENOX, I IDLER MOUNT, CHIN BELT PROPRIETRY ND CONFIDENTIL THE INFORMTION CONTINED IN THIS DRWING IS THE SOLE PROPERTY OF DLTON G. NY REPRODUCTION IN PRT OR S WHOLE WITHOUT THE WRITTEN PERMISSION OF DLTON G IS PROHIBITED. C:\_EPDM_Vault\Spreader\MOBILITY\MS Documents\MS MNULS\RC 600 & 800\ SCLE: 1:3 SHEET TITLE: IDLER, DRIVE CHIN, GD SIZE SHEET 1 OF 1 REV 30

34 , DISTRIBUTOR GER BOX ITEM PRT # DESCRIPTION QTY BOX SSEMBLY, RH PLUG, SOFT BERING GER HOUSING, RH OIL PLUG KEY, WOODRUFF SHFT, TPERED RETINER RING RETINER RING SEL TUBE SSEMBLY HOUSING BRREL TUBE SSEMBLY SHFT, TPERED PINION GER BOX SSEMBLY, LH SHFT, TPERED HOUSING, LH BRREL SSEMBLY SHFT & GER SSEMBLY GSKET HHCS, 5/16-18 x 3/ LOCK WSHER, 5/ DEGREE GRESE ZERK 2 31

35 HYDRULIC SPINNER GER BOX ROW CROP HYD SPINNERS HYDRULIC MOTOR LOCK WSHER,.375, PLTD NUT,.375 NC, PLTD FLT WSHER,.375 PLTD LOCK WSHER,.375, PLTD NUT,.375 NC, PLTD FLT WSHER,.375 PLTD BRCKET, MOTOR MOUNT FLT WSHER,.375 PLTD LOCK WSHER,.25 PLTD BOLT,.375 NC x 1.5, G5, PLTD BOLT,.25 NF x.75 SS BOLT,.375 NC x 1.25, PLTD COUPLING, CHIN, # COUPLING, HLF,.625 BR 60-I-SS #60 SS CONNECTING LINK COUPLING, HLF, 1 BR KEY,.25 x.25 x 1.25 MS DOUBLE SPINNER MOTOR MOUNT SEL KIT FOR HYDRULIC MOTOR PRT # GER BOX SET PROPRIETRY ND CONFIDENTIL THE INFORMTION CONTINED IN THIS DRWING IS THE SOLE PROPERTY OF DLTON G. NY REPRODUCTION IN PRT OR S WHOLE WITHOUT THE WRITTEN PERMISSION OF DLTON G IS PROHIBITED. DRWN BY CHECKED BY PRINT DTE CONFIG. COMMENTS: RICH SMOTHERS Default 6/17/2016 F O R P R T S, C L L /3/2013 DWG: SHEET TITLE: SIZE SCLE: 1:4 602 E. VN BUREN ST., LENOX, I ROW CROP HYD SPINNERS Sheet1 SHEET 1 OF 1 REV 32

36 TRCTOR HYDRULIC DRIVEN SPINNERS TRCTOR HYDRULIC DRIVEN SPINNERS, PRIL HYDRULIC MOTOR , FLOW CONTROL VLVE B FRONT VIEW CLOSED CENTER TRCTOR RETURN FROM TRCTOR OPEN CENTER RER VIEW RETURN TO TRCTOR FCTORY SET TO 750 RPM PROPRIETRY ND CONFIDENTIL THE INFORMTION CONTINED IN THIS DRWING IS THE SOLE PROPERTY OF DLTON G. NY REPRODUCTION IN PRT OR S WHOLE WITHOUT THE WRITTEN PERMISSION OF DLTON G IS PROHIBITED. 5 DRWN BY CHECKED BY PRINT DTE CONFIG. COMMENTS: LLong Default 5/1/2017 C:\_EPDM_Vault\Spreader\MOBILITY\MS Documents\MS MNULS\RC 600 & 800\ 4 3/31/ E. VN BUREN ST., LENOX, I DWG: TRCTOR HYDRULIC DRIVEN SPINNERS, PRIL 2017 SIZE SHEET TITLE: REV SCHEMTIC SCLE: 1:4 SHEET 1 OF

37 DIGITL REDOUT DIGITL REDOUT BCK OF DIGITL REDOUT PNEL INP NOTE: SWITCHES 7 & 8 ON THE FIRST BNK RE UP. SWITCHES 1 & 2 ON SECOND BNK RE UP. LL OTHER SWITCHES RE DOWN. GND V+ NOT USED BLCK WIRE TO GND SILVER WIRE TO GND RED WIRE TO INP SPINNER HUB NUT,.375 NF, PLTD FROM SENSOR FLT WSHER,.375 PLTD BRCKET, SENSOR, SPINNER SPEED SENSOR, SPINNER, D.R.O. OPTION W/WIRING ENCLOSURE, SPINNER D.R.O. OPTION , PNEL, DIGITL REDOUT DIGITL REDOUT KIT SENSOR SPCING TO SPINNER HUB IS BETWEEN 1/32" ND 3/16" DRWN BY CHECKED BY PRINT DTE CONFIG. COMMENTS: LLong 4/12/2017 Default 5/18/2017 DWG: 602 E. VN BUREN ST., LENOX, I DIGITL REDOUT PROPRIETRY ND CONFIDENTIL THE INFORMTION CONTINED IN THIS DRWING IS THE SOLE PROPERTY OF DLTON G. NY REPRODUCTION IN PRT OR S WHOLE WITHOUT THE WRITTEN PERMISSION OF DLTON G IS PROHIBITED. SIZE SHEET TITLE: DIGITL REDOUT 5 C:\_EPDM_Vault\Spreader\MOBILITY\MS Documents\MS MNULS\RC 600 & 800\ SCLE: 1:4 SHEET 1 OF 1 1 REV 34

38 VRIBLE RTE CONTROL, ELECTRICL PLN DRWN BY CHECKED BY PRINT DTE RICH SMOTHERS CONFIG. PROPRIETRY ND CONFIDENTIL COMMENTS: THE INFORMTION CONTINED IN THIS DRWING IS THE SOLE PROPERTY OF CMC-DLTON G. NY REPRODUCTION IN PRT OR S WHOLE WITHOUT THE WRITTEN PERMISSION OF CMC-DLTON G IS PROHIBITED. F O R P R T S, C L L E. VN BUREN ST., LENOX, I DWG: VRIBLE RTE CONTROL, ELECTRICL PLN SIZE ELECTRICL PLUMBING SHEET TITLE: SCLE: 1:10 SHEET 1 OF 1 REV 35

39 VRIBLE RTE CONTROL, HYDRULIC PLN VRIBLE RTE CONTROL, HYDRULIC PLN RETURN TO TRCTOR TO FRONT OR BOTTOM PORT OF MOTOR ELBOW FITTING TO RER OR TOP PORT OF MOTOR FROM TRCTOR FST VLVE STRIGHT FITTING 08G-8MPX HOSE END , HYDRULIC MOTOR, PROPRIETRY ND CONFIDENTIL THE INFORMTION CONTINED IN THIS DRWING IS THE SOLE PROPERTY OF DLTON G. NY REPRODUCTION IN PRT OR S WHOLE WITHOUT THE WRITTEN PERMISSION OF DLTON G IS PROHIBITED. 4 DRWN BY CHECKED BY PRINT DTE CONFIG. COMMENTS: RICH SMOTHERS FOR DWG F O R P R T S, C L L /11/2017 4/12/ E. VN BUREN ST., LENOX, I DWG: VRIBLE RTE CONTROL, HYDRULIC PLN SHEET TITLE: SIZE HYDRULIC PLUMBING SCLE: 1:3 SHEET 1 OF 1 1 REV 36

40 Calculate the Spreader Constant Value The Spreader Constant value can be calculated in one of two ways: by performing a mathematical calculation, or by performing a catch test by applying and measuring the product used. Note: The Spreader Constant value must be recalculated every time the gate opening dimensions are changed! Formula Calculation: First, use a tape measure to measure the following dimensions on the machine: Gate height (GH) in inches [cm] Gate width (GW) in inches [cm] Distance of travel (D) in inches [cm] of the belt per one revolution of the sensor Second, determine the number of pulses emitted by the encoder per one revolution of the sensor. 1. Enter a METER CL value of Enter a TOTL VOL value of Turn the sensor exactly one revolution. The value in TOTL VOLUME is the number of encoder pulses per sensor revolution. Third, determine the cubic feet [cm] of discharge per one revolution of the sensor by multiplying the distance of the belt travel per one sensor revolution by the gate height by the gate width, then dividing it by 1728 (not necessary for determining cubic cm). For Example: Distance of Belt Travel per 1 Sensor Revolution (D) = 13 inches [33 cm] Gate Height (GH) = 3 inches [18 cm] Gate Width (GW) = 8 inches [38 cm] Number of Encoder Pulses per 1 Sensor Revolution (P) = 180 D x GH x GW = Cubic Feet of Discharge per 1 Sensor Revolution x 3 x 8 =.181 cubic feet of discharge per 1 sensor revolution 1728 Finally, calculate the Spreader Constant value using one of the following formulas, using the example of a 180 CPR granular encoder. Write down this number for future reference when programming the console. Rate in Pounds: P = Spreader Constant Value Cubic Feet of Discharge per 1 Sensor Revolution 180 = 994 Spreader Constant

41 Calibration Numbers for Variable Rate Ready Spreaders Inches of belt travel per revolution of rear roller = 13 Encoder pulses per revolution of rear roller = 180 Gate Width = 8 Gate Height = ctual inches above the floor (chain is ½ thick) Meter Cal = Product Density Speed Cal w/ Sky Trak = 600 Speed Cal w/stro II = Gate Height = Gate Height = Gate Height = Gate Height = Gate Height = Gate Height = Gate Height = 600 Spreader Constant # s *The spreader constant is entered by holding down the meter cal. button until the spreader constant menu comes available. *These numbers are a good starting point and may be need to be adjusted slightly if your actual rate is off. 38

42 SCLE DETIL JUNCTION BOX, SCLE KIT SCLE KIT JUNCTION BOX , JUNCTION BOX, SCLE KIT Material <not specified> TO RER WHEEL SENSOR TO RER WHEEL SENSOR TO TONGUE SENSOR TO MONITOR WIRING SHIELD = ORNGE +EXC = GREEN -EXC = BLCK +SIG = WHITE -SIG = RED HITCH, BOLT ON, SCLE SCLE, TONGUE WEIGH SCLE HITCH , SCLE, SPINDLE, 6 TON , SCLE, SPINDLE, 8 TON , SCLE, SPINDLE, 10 TON CBLE, JUNCTION BOX TO MONITOR MOITOR (640M) CBLE, MONITOR POWER BRCKET, MONITOR MOUNTING DRWN BY CHECKED BY PRINT DTE CONFIG. COMMENTS: LLong Default 6/15/2017 4/13/2017 DWG: 602 E. VN BUREN ST., LENOX, I JUNCTION BOX, SCLE KIT PROPRIETRY ND CONFIDENTIL THE INFORMTION CONTINED IN THIS DRWING IS THE SOLE PROPERTY OF DLTON G. NY REPRODUCTION IN PRT OR S WHOLE WITHOUT THE WRITTEN PERMISSION OF DLTON G IS PROHIBITED. SIZE SHEET TITLE: Sheet1 REV 5 4 C:\_EPDM_Vault\Spreader\MOBILITY\MS Parts\ SCLE: 1: SHEET 1 OF 1 39

43 GTE MRKER DECL INFO DECL, GTE HEIGHT MRKER, LL MOBILITY MODELS W/GROUND DRIVE To replace decal: Place 3/4 thick material on top of chain, lower gate to material, set pointer at DECL, GTE HEIGHT MRKER, LL MOBILITY MODELS W/VRIBLE RTE To replace decal (Mobility VR Model): Place 1/2 material on top of chain, lower gate to material, set pointer at 1 # #640588

44 DECL LYOUT GROUND DRIVE RC SPREDER VRIBLE RTE VR TRID PM (ORNGE) M2014 M TRID PM (YELLOW) 41

45 DECL LYOUT 5910 (YELLOW) TRID PM17- TRID PM BLUE (8TON) MS029 TRID PM BLUE (8TON) MS029 TRID PM (6TON) (6TON MS031 MS

46 PRTS ORDERING PROCEDURE Your Dalton g dealer is interested in your new fertilizer application equipment and has the desire to help you get the most value from it. Through the help of this manual, you will find you can do some of the regular maintenance yourself. For parts and service, contact the Dalton g Dealership from which you purchased your fertilizer application equipment or your local Dalton g dealer. When replacement parts are required, consult the applicable illustration and parts list to obtain the correct part name and number. When requesting a replacement part, always include the following information: 1. Complete Part Number 2. Description 3. Quantity Required 4. Machine and Model Number 5. Machine Serial Number - located on the topside of the frame near hitch 6. Provide complete name and address for where and how parts are to be shipped. NOTE: Right and left hand parts and sides of the units are determined by standing at the rear and facing in the direction of forward travel. EQUIPMENT MODEL: EQUIPMENT SERIL NO.: DTE OF PURCHSE: NME OF DELER: DELER S PHONE NUMBER: Thank you for your business! Daltong.com 602 E. Van Buren Lenox, Iowa % Employee Owned 43

47 NOTES 44

48 602 E. VN BUREN / LENOX, IOW /