TRANSPORT AUGER - DRIVES

Transcription

1

2 INDEX Section B TRANSPORT AUGER - DRIVES DRIVES for models W and WR TRANSPORT AUGERS B Description Page MD Motor drive... B2 EMD Electric motor drive: W & WR x 26' & 31'... B3 W & WR 60 x 36' - 61' / x 36'-51'... B4 W 130 X 41'... B5 W & WR 80 x 56' - 71' / all W & WR B6-7 PTO-BD Drive, W & WR B8-9 PTO-SD Drive W & WR 60 x 31' - 61' / x 31'-51'... B10-11 W & WR 80 x 56' - 71' / all W & WR B12 W 130 X 41' - 71'... B13 LD Drive... B14-15 B1

3 MD - Motor Drive (W & WR60, 70, 80 Series) PART B Pulley shield Belt,B95, for 26' to 41' augers x Belt, B100, for W & WR70-46' to 51' augers x " Pulley, single groove, W & WR60 only, 1" bore " Pulley, double groove, W & WR70/80, 1" bore " roundshaft, 7-1/2" long " flangette bearing Engine carriage w/shaft & bearings 1 6A Engine carriage/level brace, bundle as shipped Shield, U-joint Slip universal joint, w/set screw & grease fitting 1 8A U-joint cross kit x /4" square shaft Std. universal joint, w/set screw & grease fitting Attach bracket, engine carriage Release strap, single, for 26' to 41' augers Release strap, single, for W & WR70-46' to 51' Motor mount Belt release handle Pulley shield, motor Criss cross leveler bracket Leveler, engine carriage Bolt, 1/4" - 20 x 1/2", grade 2 x Bolt, 5/16" - 18 x 3/4", grade 2 x Bolt, 7/16" - 14 x 1", grade 5 x PART Bolt, 7/16" - 14 x 1-3/4", grade 5 x Bolt, 1/2" - 13 x 1-1/4", grade 5 x Bolt, 5/8" - 11 x 1-1/2", grade 5 x Selftapping screw, 1/4" - 14 x 5/8", w/washerhead x Washer locknut, 1/4" - 20 x Washer locknut, 5/16" - 18 x Locknut, 7/16" - 14 x Locknut, 1/2" - 13 x Locknut, 5/8" - 11 x Set screw, 3/8" - 16 x 3/8" x Threaded grease fitting x Woodruff key, 1/4" x 1" x Square key, 1/4" x 1-1/2" x Washer locknut, 3/8" Hold down bracket Battery tray Bolt, 3/8" - 16 x 10-1/2", special 2

4 (W & WR60, 70, 80 x 26 & 31 ) EMD - Electric Motor Drive WR Double Pulley Guard Assm March 2006 and later A 18 18B 18C PART Gearbox Gearbox mount, (W & WR60) Gearbox mount, (W & WR70) Gearbox mount, (W & WR80) Shield securing bracket Tube halfband, (W & WR60) Tube halfband, (W & WR70) Tube halfband, (W & WR80) Halfband bracket, (W & WR60) Halfband bracket, (W & WR70) Halfband bracket, (W & WR80) Mount strap Electric motor mount Slip connector shield Driveshaft shield, 24" long Driveshaft shield, 42" long x Driveshaft shield, 48" long x Pulley shield Pulley shield extension Shield bracket Attach bracket Double groove 13" pulley, 1" bore Belt, B62 2 PART Flex connector, 1" x 1" bore 1 18A Flex connector sprocket, 1" bore w/keyway 1 18B Roller chain 1 18C Flex connector sprocket, 1" bore w/bolt Bolt, 1/4" - 20 x 1/2", grade 2 x Bolt, 5/16" - 18 x 5", grade 2 x Bolt, 5/16" - 18 x 2-1/2", grade 2 x Bolt, 7/16" - 14 x 1", grade 5 x Bolt, 3/8" - 16 x 3/4", grade 2 x Bolt, 1/2" - 13 x 9", special x Lockwasher, 3/8" x Washer-locknut, 1/4" - 20 x Locknut, 5/16" - 18 x Locknut, 7/16" - 14 x Hex nut, 1/2" - 13 x Setscrew, 3/8" - 16 x 3/8" x Woodruff key, 1/4" x 1" x Sq. key, 1/4" x 1-1/2" x Driveshaft connector, 1" bore Driveshaft, 1" x 28" long WR Double Pulley Guard Assm WR Double Guard Backplate Small Plastic Guard only 1 B3

5 EMD - Electric Motor Drive (W & WR60 x /70-80 x ) 18C 18B 18A 18 WR Double Pulley Guard Assm March 2006 and later REACH ARM EXTENSIONS SHOWN ON PAGE B10 PART B Gearbox Shield securing bracket Gearbox mounting plate Tube halfband, (W & WR60) 1 4A Over track halfband (WR60 x 51' & 61') Tube halfband, (W & WR70) Tube halfband, (W & WR80) Halfband bracket, (W & WR60) Halfband bracket, (W & WR70) Halfband bracket, (W & WR80) Mount strap Electric motor mount Slip connector shield Driveshaft shield, 24" long Driveshaft shield, 42" long x Driveshaft shield, 48" long x Pulley shield Pulley shield extension Shield bracket Attach bracket Double groove 13" pulley, 1" bore Belt, B Flex connector, 1" x 1" bore 1 18A Flex connector sprocket, 1" bore w/keyway 1 18B Roller chain 1 PART 18C Flex connector sprocket, 1" bore w/bolt Bolt, 1/4" - 20 x 1/2", grade 2 x Bolt, 5/16" - 18 x 5", grade 2 x Bolt, 5/16" - 18 x 2-1/2", grade 2 x Bolt, 7/16" - 14 x 1", grade 5 x Bolt, 3/8" - 16 x 3/4", grade 2 x Bolt, 1/2" - 13 x 9", special x Lockwasher, 3/8" x Washer-locknut, 1/4" - 20 x Locknut, 5/16" - 18 x Locknut, 7/16" - 14 x Hex nut, 1/2" - 13 x Setscrew, 3/8" - 16 x 3/8" x Woodruff key, 1/4" x 1" x Sq. key, 1/4" x 1-1/2" x Driveshaft connector, 1" bore Driveshaft, 1" x 4' 9" long (W&WR60, to 51') Driveshaft, 1-1/4" x 4' 6" long (W&WR80-36' & 41') Driveshaft, 1-1/4" x 10' 8-1/2" long (W80-46') Driveshaft, 1-1/4" x 10' 2-1/2" long (WR80-46') Driveshaft, 1-1/4" x 14' 4" long (W80-51') Driveshaft, 1-1/4" x 13' 10" long (WR80-51') WR Double Pulley Guard Assm WR Double Guard Backplate Small Plastic Guard only 1

6 (W 130 x 41 ) EMD - Electric Motor Drive PART Gearbox mount Gearbox Shield bracket Flex connector sprocket, 1-1/4" bore w/bolt Roller chain w/connector link Flex connector sprocket, 1-1/4" bore w/keyway Flex connector 1-1/4" x 1-1/4" bore Shield tiedown strap Flex connector shield " Triple groove pulley, 1-1/4" bore Tube halfband Electric motor mount Motor mount rail Adjust motor mount rail Narrow, shield mount angle Wide, shield mount angle Pulley shield Shield mount bracket Square washer Bolt, 1/4" - 20 x 1/2", grade 2 x PART Bolt, 5/16" - 18 x 5", grade 2 x Bolt, 3/8" - 16 x 3/4", grade 2 x Bolt, 3/8" - 16 x 2-3/4", grade 2 x Bolt, 7/16" - 14 x 1-1/4", grade 5 x Bolt, 1/2" - 13 x 1", grade 2 x Bolt, 1/2" - 13 x 9", special x Lockwasher, 1/2" x Washer - locknut, 1/4" - 20 x Washer - locknut, 5/16" - 18 x Washer - locknut, 3/8" - 16 x Locknut, 7/16" - 14 x Hex nut, 1/2" - 13 x Square key, 1/4" x 1-1/2" x Selftapping screw, 1/4" - 14 x 5/8" x B95 Belts 2 B5

7 44 EMD - Electric Motor Drive (W & WR80 x /all W & WR100) WR Triple Pulley Guard Assm March 2006 and later 45 B6

8 B7 PART PART DESCRIPTION Gearbox Gearbox mount, (W & WR80) Gearbox mount, (W & WR100) Tube halfband, (W & WR80) Tube halfband, (W & WR100) 3 3A Over track halfband (WR80 x 56' & 61') 1 3A Over track halfband (WR100 x 61') Halfband bracket, (W & WR80) Halfband bracket, (W & WR100) Mount strap Electric motor mount Gearbox shield Driveshaft shield, 24" long Driveshaft shield, 42" long X Driveshaft shield, 48" long X Pulley shield Pulley shield extension Shield bracket Attach bracket " triple groove pulley (1-1/4" bore) Belt, B Flex connector sprocket, 1-1/4" bore w/bolt Roller chain w/connector link Flex connector sprocket, 1" bore w/keyway Flex connector sprocket, 1-1/4" bore w/keyway Flex connector, 1" x 1-1/4" bore Flex connector, 1-1/4" x 1-1/4" bore Bolt, 1/4" - 20 x 1/2", grade 2 X Bolt, 5/16" - 18 x 5", grade 2 X Bolt, 3/8" - 16 x 2-3/4", grade 2 X Bolt, 7/16" - 14 x 1, grade 5 X Bolt, 1/2" - 13 x 1, grade 2 X Bolt, 1/2" - 13 x 9", special X Lockwasher, 1/2 X Washer-locknut, 1/4" - 20 X Locknut, 5/16" - 18 X Washer-locknut, 3/8" - 16 X Locknut, 7/16" - 14 X Hex nut, 1/2" - 13 X Setscrew, 3/8" - 16 x 3/8" X Square key, 1/4" x 1-1/2" X Driveshaft connector, (W & WR80) Driveshaft connector, (W & WR100) Shield securing bracket PART PART DESCRIPTION Driveshaft, 1-1/4" x 18' 9" (W & WR80-56' & 61') Driveshaft, 1" x 6" W80-71' only Driveshaft, 1" x 19" WR80-71' only Driveshaft, 1-1/4" x 3' 10" (W & WR100-31') Driveshaft, 1-1/4" x 6' 2-1/2" (W & WR100-41') Driveshaft, 1-1/4" x 11' 8" (W& WR100-51') Driveshaft, 1-1/4" x 18' 9" (W & WR100-61') Driveshaft, 1-1/4" x 6" W100-71' only Driveshaft, 1-1/4" x 19" WR100-71' only Shield for 3 shaft gearbox Chain coupler shield Shield tie down strap Selftapping screw, 1/4" - 14 x 5/8" Bolt, 3/8" - 16 x 3/4", grade WR Triple Pulley Guard Assm WR Triple Guard Backplate Large Plastic Guard only 1 EMD - Motor Drive (W & WR80 x / all W & WR 100)

9 PTO - BD (Belt Drive) W & WR60, 70, 80 Series 33 9A 9B9C 9 10 B8

10 B9 PART PART DESCRIPTION Small pulley shield " pulley, single groove, W & WR60 only 1" bore x " pulley, double, W & WR70 & 80 only 1" bore x Gearbox, BD Shield, slip connector x " shield, driveshaft Shield securing bracket Driveshaft, 1" x 4' 9" long, W & WR60, 70-36' to 51' Driveshaft, 1-1/4" x 4' 5-1/2" long, W80-36' & 41' Driveshaft, 1-1/4" x 10' 8-1/2" long, W80-46' only Driveshaft, 1-1/4" x 10' 2-1/2" long, WR80-46' only Driveshaft, 1-1/4" x 14' 4" long, W80-51' only Driveshaft, 1-1/4" x 13' 10" long, WR80-51' only Driveshaft connector Flex connector, 1" x 1" bore 1 9A Flex connector sprocket, 1" bore w/keyway 1 9B Roller chain 1 9C Flex connector sprocket, 1" bore w/bolt Mounting plate, gearbox Spacer bracket Extension, left reach arm Extension, right reach arm " crossmember Channel, belt guide Belt guide, single /4" support tube, W &WR60, 70, 80-36' augers /4" support tube, W & WR60, 70, 80-41' augers /4" support tube, W & WR70, 80-46' augers /4" support tube, W & WR70, 80-51' augers " support tube, 36' to 41' augers " support tube, 46' to 51' augers Sliding bracket, jackshaft, 36' augers Sliding bracket, jackshaft, 41' to 51' augers Transport saddle, PTO driveline, less pin & bolt Saddle pin, less hairpin Hairpin PTO driveline, 48" " round shaft, 23" long, for 36' to 46' augers " round shaft, 28" long, for 51' augers " Flangette bearing " Bearing, less flanges Jackshaft w/bearings & shaft, for 36' to 46' augers Jackshaft w/bearings & shaft, for 51' augers " pulley, single groove, W & WR60 augers 1" bore 1 PART PART DESCRIPTION " pulley, double groove, 1" bore, W & WR70/80 augers X Belt B180, for 36' augers, 1 on W & WR60, 2 on W & WR70/80 X Belt B210, for 41' augers, 1 on W & WR60, 2 on W & WR70/80 X Belt B240, for 46' augers Belt B270, for 51' augers Pulley shield, large Bolt, 1/4" - 20 x 1/2", grade 2 X Bolt, 5/16" - 18 x 3/4", grade 2 X Bolt, 5/16" - 18 x 2-1/2", grade 2 X Bolt, 3/8" - 16 x 3/4", grade 2 x Bolt 7/16" - 14 x 1, grade 5 x Bolt, 7/16" - 14 x 2-1/4", grade 8 x Bolt, 7/16" - 14 x 3", grade 2, for 36" augers x Bolt, 7/16" - 14 x 3-1/2", grade 2, for 41 to 51 augers x Bolt, 7/16" - 14 x 8", special x Bolt, 1/2" - 13 x 1-1/4", grade 5 x Bolt, 5/8" - 11 x 1-1/2", grade 5 x Washer locknut, 1/4" - 20 x Washer locknut, 5/16" - 18 x Washer locknut, 3/8" - 16 x Square key, 1/4" x 2-1/2" x Locknut, 7/16" - 14 x Locknut, 1/2" - 13 x Locknut, 5/8" - 11 x Lockwasher, 3/8" x Set screw, 3/8" - 16 x 3/8" x U-Bolt, 3/8" - 16 x 2", for 36' augers x U-Bolt, 3/8" - 16 x 2-1/2", for 41 to 51 augers x Woodruff key, 1/4" x 1" x Square key, 1/4" x 1-1/2" x Jackshaft w/bearings & shaft, for 36' to 46' augers Jackshaft w/bearings & shaft, for 51' augers Shield assembly with rubber Rubber flap Rubber mount strap PTO-BD (Belt Drive) (W & WR60, 70, 80 Series)

11 PTO - SD (Shaft Drive) (W & WR60 x /70-80 x ) 25 11C 11B 11A 11 B10

12 B11 PART 6" 7" 8" Gearbox Gearbox mount Tube halfband x Shield, gearbox Shield, slip connector " shield, driveshaft x 6A " shield, driveshaft x Bracket, shield securing " driveshaft, 4' 9" long, (W & WR60-36'/41', W & WR70-36' to 51') /4" driveshaft, 4' 5-1/2" long, W&WR80-36'/41' /4" driveshaft, 10' 8-1/2" long, W80-46' only /4" driveshaft, 10' 2-1/2" long, WR80-46' only /4" driveshaft, 14' 4" long, W80-51' only /4" driveshaft, 13' 10" long, WR80-51' only Driveshaft connector x " driveshaft, 7' 3/4" long, (W & WR31' models) " driveshaft, 3' 2-1/2" long, (W & WR36' models) " driveshaft, 4' 4" long, (W & WR41' models) " driveshaft, 5' 9" long, (W & WR46' models) " driveshaft, 7' 3/4" long, (W & WR51' models) /4" driveshaft, 3' 5-1/2" long, (W & WR36' models) /4" driveshaft, 47" long, (W & WR41' models) /4" driveshaft, 6' 0" long, (W & WR46' models) /4" driveshaft, 7' 4-1/2" long, (W & WR31' models) (W&WR51' models) Flex connector, 1" x 1" bore 1 11A Flex connector sprocket, 1" bore w/keyway 1 11B Roller chain 1 11C Flex connector sprocket, 1" bore w/bolt Strap-on bearing x Transport saddle Saddle pin Hairpin PTO driveline, 60" long Sprocket, Sprocket, Roller chain w/connector Bolt, 1/4" - 20 x 1/2", grade 2 X Bolt, 5/16" - 18 x 2-1/2", grade 2 x Bolt, 3/8" - 16 x 3/4", grade 2 x PART 6" 7" 8" Bolt, 7/16" - 14 x 1, grade 5 X Washer locknut, 1/4" - 20 X Washer locknut, 5/16" - 18 X Locknut, 7/16" - 14 X Lockwasher, 3/8" X Set screw, 5/16" - 18 x 3/8" x Set screw, 3/8" - 16 x 3/8" x Woodruff key, 1/4" x 1" x Square key, 1/4" x 1-1/2" x Cross member, 19" long, 46' - 51' models x Bolt, 1/2" - 13 x 1-1/4", grade 5 x Bolt, 5/8" - 11 x 1-1/2", grade 5 x Locknut, 1/2" - 13 x Locknut, 5/8" - 11 x Reach arm extension, left or right, 46'-51' models 2 37A Reach arm extension bundle Shield assembly with rubber Rubber flap Rubber mount strap Shield attach plate Bolt, 5/16" - 18 x 3/4", grade Washer locknut, 3/8" SD gearbox, mount, half connector, as packed 1 PTO-SD (Shaft Drive) (W & WR60 x / x )

13 PTO - SD (Shaft Drive) (W&WR 80x56-71 all W&WR 100) PART PART Gearbox, SD Locknut, 7/16" Mount, gearbox, less halfbands Lockwasher, 1/2" Halfband, tube Setscrew, 5/16" - 18 x 3/8" Shield, gearbox Sq. key, 1/4" x 1-1/2" Bracket, shield securing Bolt, 5/16" - 18 x 3/4", grade Sprocket, flex connector, 1-1/4" bore w/bolt hole Bolt, 3/8" - 16 x 3/4", grade Roller chain w/connector link Washer locknut, 5/16" Sprocket, flex connector 1" bore Self tapping screw, 1/4" - 14 x 5/8" Sprocket, flex connector, 1-1/4" bore Shield tiedown strap Complete flex connector Rubber flap Transport saddle, PTO, less halfband Rubber mount strap Saddle pin, less hairpin Shield assembly with rubber Hairpin Shield attach plate PTO driveline, 60" long Shield for 3 shaft gearbox Bolt, 1/4" - 20 x 1/2", grade Chain coupler shield Bolt, 3/8" - 16 x 2-3/4", grade SD gearbox, mount, flex connector, as packed Bolt, 7/16" - 14 x 1, grade Bolt, 1/2" - 13 x 1", grade Washer locknut, 1/4" Washer locknut, 3/8" - 16 B12

14 PTO-SD (Shaft Drive) (W130 x ) PART Gearbox Gearbox mount, less halfbands Tube halfband Flex connector sprocket, 1-1/4" bore w/bolt hole Flex connector sprocket, 1-3/4" bore Roller chain w/connector link Flex connector sprocket, 1-1/4" bore Flex connector sprocket, 1-1/2" bore Complete flex connector Chain coupler shield Shield tiedown strap Shield attach plate Shield assembly with rubber Rubber flap Rubber mount strap Transport saddle, less halfband PTO driveline Saddle pin, less hairpin Hairpin Bolt, 5/16" - 18 x 3/4", grade 2 PART Bolt, 3/8" - 16 x 3/4", grade Bolt, 3/8" - 16 x 2-3/4", grade Bolt, 7/16" - 14 x 1-1/4", grade Bolt, 1/2" - 13 x 1", grade Bolt, 5/8" - 11 x 1", grades Washer locknut, 5/16" Washer locknut, 3/8" Locknut, 7/16" Selftapping screw, 1/4" - 14 x 5/8" Setscrew, 5/16" - 18 x 3/8" Setscrew, 3/8" - 16 x 3/8" Square key, 1/4" x 1-1/2" Square key, 3/8" x 1-3/4" Lockwasher, 1/2" Lockwasher, 5/8" B13

15 LD - Drive 26A 26B 26C 26 B14

16 LD-Drive B15 PART PART DESCRIPTION Support tube assembly, outer Support tube assembly, inner Motor mount Assembly Leveling arm, long Extension, leveling arm (46' & 51' only) Leveling arm, short Right reach arm extension Left reach arm extension Shot crossmember Hanger bracket Leveler plate Belt release handle Release strap Support bracket, belt guide Belt guide Leaver guide Attach plate Attach bracket, leveler Spacer bracket Bracket, Pulley guard Guard, motor pulley Guard, gearbox pulley Shield, slip connector Driveshaft, shield 48" Gearbox Flex connector, 1" x 1" bore 1 26A Flex connector sprocket, 1" bore w/keyway 1 26B Roller chain 1 26C Flex connector sprocket, 1" bore w/bolt Gearbox mounting plate Pulley, 13" double groove, 1" bore Belt, B210, (41' augers) Belt, B240, (46' augers) Belt, B270, (51' augers) Driveshaft (641, 741, 746 & 751 augers) Driveshaft (841 auger) Driveshaft (846 auger) Driveshaft (851 auger) Driveshaft connector adjusting bolt Shield Securing bracket U-bolt, 3/8" x 2-1/2" Bolt, 1/4" - 20 x 1/2", Grade 2 x Bolt, 5/16" - 18 x 1", Grade 2 x PART PART DESCRIPTION Bolt, 5/16" - 18 x 2-1/2", Grade 2 x Bolt, 3/8" - 16 x 3/4", Grade 2 x Bolt, 7/16" - 14 x 1", Grade 5 x Bolt, 7/16" - 14 x 2-1/4", Grade 8 x Bolt, 7/16" - 14 x 3", Grade 5 x Bolt, 1/2" - 13 x 1-1/4", Grade 5 x Bolt, 3/4" - 10 x 2", Grade 5 x Set screw 3/8" - 16 x 3/8" x Washer locknut, 1/4" - 20 x Washer locknut, 5/16" - 18 x Washer locknut, 3/8" - 16 x Locknut, 7/16" - 14 x Locknut, 1/2" - 13 x Locknut, 3/4" - 10 x Lockwasher, 3/8" x Washer, 3/4" x Woodruff key, 1/4" x 1" Square Key, 1/4" x 1-1/2" Battery tray Hold down bracket Bolt, 3/8" - 16 x 10-1/2", special 2