BH AUGERS BH 836, BH 1036, BH 841, BH 1041, BH 846, & BH 851 ASSEMBLY MANUAL

Size: px
Start display at page:

Download "BH AUGERS BH 836, BH 1036, BH 841, BH 1041, BH 846, & BH 851 ASSEMBLY MANUAL"

Transcription

1 BH AUGERS ASSEMBLY MANUAL Read this manual before using product. Failure to follow instructions and safety precautions can result in serious injury, death, or property damage. Keep manual for future reference. Part Number: R1 Revised: 25/5/11

2 This product has been designed and constructed according to general engineering standards a. Other local regulations may apply and must be followed by the operator. We strongly recommend that all personnel associated with this equipment be trained in the correct operational and safety procedures required for this product. Periodic reviews of this manual with all employees should be standard practice. For your convenience, we include this sign-off sheet so you can record your periodic reviews. Date Employee Signature Employer Signature a. Standards include organizations such as the American Society of Agricultural and Biological Engineers, American National Standards Institute, Canadian Standards Association, International Organization for Standardization, and/or others.

3 WHEATHEART - BH AUGERS TABLE OF CONTENTS 1. Introduction Safety First General Safety Assembly Safety Safety Decal Locations Decal Installation Decal Locations Assembly General Assembly Auger Tube Assembly Tube & Flighting Assembly Intake Assembly Drive Shaft Assembly Gearbox Assembly Drive Shaft Shield & Pulley Guard Assembly Truss & Cable Assembly Bridge/Cable Installation & Cable Tightening Lift Cable Installation Frame Assembly Lower Frame Assembly Lift Arm Assembly Tire Assembly Attaching To Tube Cross Member / Cable Pulley Assembly Hand Winch & Idler Assembly Drive Assembly Gas Engine & Components Electric Motor & Components PTO & Components Australian Belt Guard Assembly Decal Installation Decal Placement Appendix Bolt Torque Values Tightening O-Ring Fittings Limited Warranty R1 3

4 WHEATHEART - BH AUGERS R1

5 WHEATHEART - BH AUGERS 1. Introduction 1. INTRODUCTION Congratulations on the purchase of your new Wheatheart BH Auger. This piece of equipment will complement your agricultural operation by aiding in the safe and efficient movement of grain, pulse crops, fertilizer, or any other granular materials. Your new Wheatheart auger will serve you well if you understand how it operates, if you use it properly, and if you care for it properly. This manual is intended to help you assemble your equipment in a safe, efficient, and troublefree manner. Please read this manual completely before assembling your new grain auger. This assembly manual covers all BH augers built by Wheatheart Manufacturing, so please use the Table of Contents as a guide when searching for specific information. Keep this manual in a safe place for future reference. Should any information remain unclear after thoroughly reviewing this manual, contact your Wheatheart Dealer for clarification before assembling your auger. Knowing the serial number and date of purchase will save time in getting your questions answered. Please write down this information in the space provided below R1 5

6 1. INTRODUCTION WHEATHEART - BH AUGERS R1

7 WHEATHEART - BH AUGERS 2. Safety First 2. SAFETY FIRST The Safety Alert symbol to the left identifies important safety messages on the product and in the manual. When you see this symbol, be alert to the possibility of personal injury or death. Follow the instructions in the safety messages. Why is SAFETY important to you? Three big reasons: Accidents disable and kill. Accidents cost. Accidents can be avoided. SIGNAL WORDS Note the use of the signal words DANGER, WARNING, CAUTION, and NOTICE with the safety messages. The appropriate signal word for each message has been selected using the definitions below as a guideline. The Safety Alert symbol means: ATTENTION, BE ALERT! YOUR SAFETY IS INVOLVED. DANGER Indicates an imminently hazardous situation that, if not avoided, will result in serious injury or death. WARNING Indicates a hazardous situation that, if not avoided, could result in serious injury or death. CAUTION Indicates a hazardous situation that, if not avoided, may result in minor or moderate injury. NOTICE Indicates a potentially hazardous situation that, if not avoided, may result in property damage R1 7

8 2. SAFETY FIRST WHEATHEART - BH AUGERS 2.1. GENERAL SAFETY 2.1. GENERAL SAFETY Important: The general safety section includes instructions that apply to all safety practices. Any instructions specific to a certain safety practice (e.g., assembly safety), can be found in the appropriate section. Always read the complete instructional sections and not just these safety summaries before doing anything with the equipment. YOU are responsible for the SAFE use and maintenance of your equipment. YOU must ensure that you and anyone else who is going to work around the equipment understands all procedures and related SAFETY information contained in this manual. Remember, YOU are the key to safety. Good safety practices not only protect you, but also the people around you. Make these practices a working part of your safety program. It is the equipment owner and the operator's responsibility to read and understand ALL safety instructions, safety decals, and manuals and follow them before assembling, operating, or maintaining the equipment. All accidents can be avoided. Equipment owners must give instructions and review the information initially and anually with all personnel before allowing them to operate this product. Untrained users/operators expose themselves and bystanders to possible serious injury or death. Use this equipment for its intended purposes only. Do not modify the equipment in any way. Unauthorized modification may impair the function and/or safety, and could affect the life of the equipment. Any modification to the equipment voids the warranty. Do not allow children, spectators, or bystanders within the work area. Have a first-aid kit available for use should the need arise, and know how to use it. Provide a fire extinguisher for use in case of an accident. Store in a highly visible place. Wear appropriate protective gear. This list includes, but is not limited to: a hard hat gloves protective shoes with slip-resistant soles protective goggles hearing protection dust mask or respirator For Powered Equipment: before servicing, adjusting, or repairing powered equipment, unplug, place all controls in neutral or off position, stop the engine or motor, remove ignition key or lock out power source, and wait for all moving parts to stop R1

9 WHEATHEART - BH AUGERS 2. SAFETY FIRST 2.2. ASSEMBLY SAFETY Follow good shop practices: keep service area clean and dry be sure electrical outlets and tools are properly grounded use adequate light for the job at hand Think SAFETY! Work SAFELY! 2.2. ASSEMBLY SAFETY Read the instructions and familiarize yourself with the subassemblies and hardware making up the equipment. The components are large, heavy, and can be hard to handle. Be sure to use the proper tools, stands, jacks, and hoists for the job. Have 2 people handle the heavy bulky components. Place safety stands or large blocks under the machine or components before going beneath the component for assembly. Stay away from overhead power lines and obstructions when lifting the machine during assembly. Electrocution can occur without direct contact. Contact with obstructions can damage components or cause them to fail. Tighten all fasteners to their specified torque before using the machine SAFETY DECAL LOCATIONS Keep safety decals clean and legible at all times. Replace safety decals that are missing or have become illegible. See decal location figures that follow. Replaced parts must display the same decal(s) as the original part. Safety decals are available from your distributor, dealer, or factory DECAL INSTALLATION 1. Decal area must be clean and dry, with a temperature above 50 F (10 C). 2. Decide on the exact position before you remove the backing paper. 3. Align the decal over the specified area and carefully press the small portion with the exposed sticky backing in place. 4. Slowly peel back the remaining paper and carefully smooth the remaining portion of the decal in place. 5. Small air pockets can be pierced with a pin and smoothed out using the sign backing paper R1 9

10 2. SAFETY FIRST WHEATHEART - BH AUGERS 2.3. SAFETY DECAL LOCATIONS DECAL LOCATIONS Replicas of the safety decals that are attached to the equipment are shown in the figure(s) that follow. Proper safety procedures require that you familiarize yourself with the various safety decals and the areas or particular functions that the decals apply to as well as the safety precautions that must be taken to avoid serious, injury, death, or damage R1

11 WHEATHEART - BH AUGERS 2. SAFETY FIRST 2.3. SAFETY DECAL LOCATIONS DECAL #17102 DECAL #17098 DECAL #17096 DECAL #17109 DECAL #17101 DECAL #19960 DECAL #17097 DECAL #17113 Figure 2.1 Safety Decals R1 11

12 2. SAFETY FIRST WHEATHEART - BH AUGERS 2.3. SAFETY DECAL LOCATIONS DECAL # DECAL # DECAL # DECAL #17098 DECAL #17097 DECAL #17102 DECAL #17101 DECAL # Figure 2.2 Safety Decal Locations If safety signs have been damaged, removed, or become illegible, or if parts are replaced without safety signs, new signs must be applied. New safety signs are available from your authorized dealer R1

13 WHEATHEART - BH AUGERS 3. Assembly 3. ASSEMBLY 3.1. GENERAL ASSEMBLY Warning: Before continuing, please read the safety information relevant to this section in the safety section of this manual. Failure to follow the safety instructions can result in serious injury, death, or property damage. Important: Before starting the assembly of your new auger, please read the following instructions carefully, and familiarize yourself with all the sub-assemblies and hardware making up the auger. Ensure that all parts are on hand, arranging them for easy access as required. Assembly should be carried out in a large open area with a level surface. Do not take chances with safety. The components are large, heavy, and can be hard to handle. Be sure to use the proper tools, stands, jacks, and hoists for the job. These instructions are written on the assumption that two or more people will be available for the assembly procedure. Because of the weight, it is unwise to attempt assembly of the auger alone. Augers are available in various combinations. In most instances, the following instructions will apply to all augers. Where the assembly information for a particular set-up varies from a given step, additional instructions are included, indicated by an arrow at the appropriate point in the text. When tightening all fasteners, refer to Appendix for proper torque specifications GENERAL ASSEMBLY 1. Select an assembly area that is level, has a firm or hard surface, and is free of debris. Be sure it is large enough to allow access from all sides when the components are being assembled. 2. If assembling inside a building, be sure the ceiling is at least 14 (4.27 m) high to provide clearance when installing the undercarriage. 3. Bring all the tools, blocks, stands, jacks, and hoists to the assembly area before starting. The following tools and equipment are required to assemble the machine: : 2-4 Pipe stands 2 Saw horses (support capacity of 1200 lb, 544 kg) 1 Standard socket set and wrench set 1 Torque wrench 1 Standard 25' (7.7 m) tape measure 1 2' (600 mm) level 1 8" (200 mm) level, magnetic 2 C-clamps or vice grips R1 13

14 3. ASSEMBLY WHEATHEART - BH AUGERS 3.2. AUGER TUBE ASSEMBLY 1 Lifting device with minimum reach of 12' (3.7 m) and lb (1800 to 2700 kg) lifting capacity 1 100' measuring tape 1 Tire pressure gauge 1 Tire chuck 3.2. AUGER TUBE ASSEMBLY TUBE & FLIGHTING ASSEMBLY ALL AUGERS FIGURE 3.1 AND 3.2 See Table 3.1 for the number of tube sections and their lengths. 1. Align tube sections on a series of stands, placing a saw horse at each end with a stand at the flanges. Set the stand height so flanges are flush and level. 2. Slide the lower flighting shaft into the upper flighting shaft with flight ends butting together for continuous flow. Secure with two 7/16 x 2-1/4 GR8 bolts (1) and 7/16 locknuts (2) for the 8. (Use1/2 x 2-3/4 GR8 bolts and 1/2 locknuts for the BH 1036 and BH 1041). 3. Slide tube sections together and insert the eight 7/16 x 1 GR5 bolts (3) and 7/16 locknuts (4). Ensure the tube sections are aligned so the brackets are in the proper position. Tighten evenly. 4. Slide roller track shoe (5) onto track. Table 3.1 Model Total Number of Tube Sections BH 836, BH BH 841, BH BH BH Lower Tube Section Length 10' (3.05 m) 15' ( 4.57 m) 20' (6.10 m) 25 (7.62 m) Upper Tube Section Length 25' (7.62 m) 25' (7.62 m) 25' (7.62 m) 25' (7.62 m) R1

15 WHEATHEART - BH AUGERS 3. ASSEMBLY 3.2. AUGER TUBE ASSEMBLY Figure 3.1 See Table 3.2 for track shoe stop bracket location. 5. For the BH 841,BH 1041, BH 846, and BH 851 augers, the upper angle-iron track stop (6) is attached to the set of holes in the track closest to the discharge end. For the BH 836 and BH 1036 auger, use the second set of holes (7) from the discharge end. (See Figure 3.2.) 6. Secure the upper angle-iron track stop (6, 7) with two 7/16 x 1 bolts (8) and locknuts (9). (See Figure 3.2.) 7. Locate the lower angle-iron track stop (10) location according to Table 3.2, and attach it with two 7/16 x 1 bolts (8) and locknuts (9). See Figure 3.2. Table 3.2 Model Z Y BH 836, BH /8 (2.69 m) BH 841, BH /16 (3.36 m) - BH /16 (3.87 m) - BH /16 (4.40 m) - Figure R1 15

16 3. ASSEMBLY WHEATHEART - BH AUGERS 3.2. AUGER TUBE ASSEMBLY INTAKE ASSEMBLY ALL AUGERS SEE FIGURE Clean dirt and paint from lower flighting stub (1) and from inside of the bushing (2) on the intake. 2. Slide the intake flighting (3) over the lower flighting shaft (4) and tighten the 3/8 x 2-1/2 bolt (5) and locknut (14). 3. Attach the bolt-on intake guard (6) to lower auger tube (7) using six 7/16 x 1 bolts (8) and 7/16 locknuts (9). TIGHTEN SECURELY. 4. Maintain a 1/2 (1.27 cm) clearance between the bushing and the end of the flighting. 5. Attach the hitch clevis (10) to the intake guard (6) with a 5/8 clevis pin (11) and a hairpin (12). 6. Make sure that the grease zerk (13) is installed and secure. Grease the bushing. See the Operation Manual for regular maintenance procedures. INTAKE ASSEMBLY TOP Figure R1

17 WHEATHEART - BH AUGERS 3. ASSEMBLY 3.2. AUGER TUBE ASSEMBLY DRIVE SHAFT ASSEMBLY Important: ALL AUGERS SEE FIGURE 3.4 See Table 3.3 for the lower driveshaft length and diameter. 1. Clean dirt and paint from the driveshaft ends (1, 2) and the shaft connector (3). Refer to Figure After installing the Woodruff key (4), slide connector (3) halfway onto the last pre-installed driveshaft segment (1) as shown in Figure 3.4. It may ease installation if the bolts on the bearings are loosened or removed. 3. Slip the lower driveshaft segment (5) through the bearing(s) (6) on the lower tube section, install a Woodruff key (7), and slide it into the shaft connector (3) as shown in Figure 3.4. The BH 836, BH 1036, BH 841 and BH 1041 augers do not have bearings on the lower tube section. 4. Center the coupler on the keys so an 1/8 (3 mm) is sticking out each end and tighten the set screws (8) on the shaft connector (3). Refer to Figure 3.4. Place a few drops of oil at each driveshaft bearing location to allow for a break-in period. These bearings will not require any further lubrication as they are selflubricated. Table 3.3 Model BH 836, BH 1036 BH 841, BH 1041 BH 846 BH 851 Length 17" (0.43 m) 53" (1.35 m) 89" (2.26 m) 125" (3.18 m) Lower Driveshaft Diameter 1-1/4 (3.2 cm) 1-1/4 (3.2 cm) 1-1/4 (3.2 cm) 1-1/4 (3.2cm) R1 17

18 3. ASSEMBLY WHEATHEART - BH AUGERS 3.2. AUGER TUBE ASSEMBLY Figure GEARBOX ASSEMBLY ALL AUGERS Check the gearbox oil level; gearbox should be half full. Use only EP90 lube oil and fill to HALF FULL only. See the Operation Manual for the correct maintenance procedures. 1. Secure the coupler (1) to the driveshaft (2) using a woodruff key (3) and set screw (4). The driveshaft should be flush with the sprocket (see Figure 3.5.). 2. Bolt the mounting plate (5) to the gearbox (6) using four 3/8 x 3/4 bolts (7) and 3/8 lock washers (8) as shown in Figure Slide the gearbox shaft (14) into the coupler (1). Secure the gearbox and mounting plate assembly to the mounting bracket (9) welded to the tube using four 7/16 x 1 bolts (10) and 7/16 locknuts (11). Refer to Figure Attach the other end of the coupler to the gearbox shaft (14) with a 5/16 x 2-3/4 bolt (12) and 5/16 locknut (13) as shown in Figure 3.5. Ensure a gap of 1/16 (1.6 mm) between the chain coupler sprockets. 5. If the driveshaft is too long or too short, do the following: If driveshaft is too long, take up the extra length in the coupler between the two shafts R1

19 WHEATHEART - BH AUGERS 3. ASSEMBLY 3.2. AUGER TUBE ASSEMBLY If driveshaft is too short, slide coupler (1) off driveshaft (2) up to 1/8 (3 mm). If more length is required, the chain cover at the discharge end will need to be removed. Loosen the set screws that hold the gear and locking collar on the driveshaft. Unlock the camlock collar and slide the driveshaft until the holes in the gearbox shaft (14) and the coupler (1) line up. Relock the camlock. Line up the sprockets and retighten the set screws. 6. If the chain cover at the discharge end is in place, remove it. 7. Fill the cover half full of grease and lube the chain with chain lube. Reinstall the cover. Figure DRIVE SHAFT SHIELD & PULLEY GUARD ASSEMBLY See Table 3.4 for shield sizes and quantity. Shield installation starts at the gearbox and ends at the discharge end. 1. Clean dirt and paint from the gearbox shaft (1) and the pulley (2) as shown in Figure 3.6. Pulley used depends on the power source; refer to Drive Assembly on pg. 35 for the correct pulley selection. NORTH AMERICA ONLY: 2. Install a 1/4 x 1-1/2 square key (3) on the gearbox shaft (1) and slide the pulley (2), with the hub facing the gearbox, until it is flush with the shaft. Secure by tightening the set screw (4). Refer to Figure R1 19

20 3. ASSEMBLY WHEATHEART - BH AUGERS 3.2. AUGER TUBE ASSEMBLY NORTH AMERICA ONLY: Attach the connector shield (5) and the pulley guard (6) to the gearbox (7) using three 3/8 x 3/4 bolts (8), three 3/8 lock washers (9) and one 3/8 flat washer (10) used as a spacer between the pulley guard and the gearbox as shown in Figure 3.6. AUSTRALIA ONLY: Attach the connector shield (5) to the gearbox (7) using two 3/8 x 3/4 bolts (8) and two 3/8 lock-washers (9). Refer to Figure Attach the first driveshaft shield (11) to the connector shield (5) with one 1/4 x 3/4 bolt (12), punched flat iron plate (13), and a 1/4 locknut (14). Refer to Figure 3.6. The driveshaft shield is pinched between the flat iron plate and the connector shield. 4. The next driveshaft shield (15) is placed on top of the first shield (11) and secured in place with a shield strap (16) and two 1/4 x 5/8 self-tapping screws (17) as shown in Figure Repeat until the last shield (18) is secured to the bearing adjustment plate (19) with a shield strap (20) and two 1/4 x 5/8 self-tapping screws (21). Refer to Figure 3.6. Repeat until the second last shield is completed. Table 3.4 Model Shield Length (Starting at Gearbox) Total Number of First Middle Last Shields BH 836, BH " 60" 48" (0.61 m) (1.52 m) (1.22 m) 6 BH 841, BH " 60" 48" (1.52 m) (1.52 m) (1.22 m) 6 BH " 60" 48" 7 BH 851 (1.07 m) 60" (1.52 m) (1.52 m) 60" (1.52 m) (1.22 m) 48" (1.22 m) R1

21 WHEATHEART - BH AUGERS 3. ASSEMBLY 3.3. TRUSS & CABLE ASSEMBLY Figure TRUSS & CABLE ASSEMBLY BRIDGE/CABLE INSTALLATION & CABLE TIGHTENING BH 851 AUGER ONLY Refer to Figure 3.7 for following instructions. 1. Fasten the cable bridge (1) to the bracket (2) welded to the tube with two 7/16 x 1 GR5 bolts (3) and 7/16 locknuts (4). 2. Loosely attach cable clamps - two cable clamps (17) on the cable bridge and one clamp (18) on the cable return bracket. 3. Slide the truss cable anchors (5) onto the pivot bushings (6) using 1 SAE washers (7) as spacers. Temporarily secure the anchors in place with 1/2 flat washers (8), 1/2 lock washers (9), and 1/2 x 1 bolt (10). When the frame is attached to the tube, the washers, lock washers, and bolts will be removed and used to secure the lower frame arms in place. 4. Slide the two 5/16 x 12 clear hose (19) pieces onto the truss cable, placing them approximately at the midpoint of the cable length. 5. Thread a jam nut (14) onto an eyebolt (11) all the way. Attach the eyebolt (11) to one end of the truss cable (12) with two 1/4 cable clamps (13) doublingback about 8 of cable. Insert the eyebolt (11) into the truss cable anchor bracket (5) and thread on a 1/2 locknut (15) a short way. 6. Pull the truss cable (12) over the cable bridge (1), through the cable clamps (17, 18), around the cable return bracket (16), back over the cable bridge (1), R1 21

22 3. ASSEMBLY WHEATHEART - BH AUGERS 3.3. TRUSS & CABLE ASSEMBLY and back to the other cable anchor bracket (5). Ensure that the two 5/16 x 12 clear hoses (19) are on opposite sides of the cable return bracket (16) and approximately in the position where the cable will contact the tube. DO NOT tighten the cable clamps at this time. 7. Thread a jam nut onto the other eyebolt all the way, place the eyebolt in the cable anchor bracket, and thread on a 1/2 locknut a short way. 8. Thread the end of the truss cable through the eyebolt and pull the cable snug. Double-back the cable and secure in place with two cable clamps as in step 5. If there isn t enough cable, loosen the clamps on the opposite eyebolt and adjust the cable. Retighten clamps. 9. Place the two 5/16 x 12 clear hoses (19) so that none of the truss cable is in contact with the tube. 10. Tighten the eyebolts evenly to take the remaining slack out of the truss cable. DO NOT put tension in the cable or the auger will have too much droop at the flange when it is in the lowered position. 11. Check for proper side-to-side alignment and then tighten the cable clamps on the cable bridge and the cable return bracket. Tighten the jam nuts (14) against the cable anchor bracket (5) holding the eyebolt (11) from turning and such that the cable clamps (13) won t scratch the tube R1

23 WHEATHEART - BH AUGERS 3. ASSEMBLY 3.3. TRUSS & CABLE ASSEMBLY Figure R1 23

24 3. ASSEMBLY WHEATHEART - BH AUGERS 3.3. TRUSS & CABLE ASSEMBLY LIFT CABLE INSTALLATION ALL AUGERS See Table 3.5 for the proper cable length. 1. Attach the cable (1) to the cable attach rod (2) welded to the bottom of the track by wrapping it around the rod and doubling-back about 6 (15 cm) of cable, as shown in Figure Secure the cable in place by installing and tightening two cable clamps (3). Refer to Figure Thread the cable (4) under the angle iron track stop (6) and through the track shoe (5) as shown in Figure Coil the remaining cable and secure it to the tube making sure that the track shoe can slide all the way to the track stop at the discharge end of the track. Table 3.5 Model Lift Cable Length 35' BH 836, BH 1036 (10.7 m) 40' BH 841, BH 1041 (12.2 m) 44' BH 846 (13.4 m) 49' BH 851 (14.9 m) R1

25 WHEATHEART - BH AUGERS 3. ASSEMBLY 3.4. FRAME ASSEMBLY Figure FRAME ASSEMBLY LOWER FRAME ASSEMBLY ALL AUGERS See Table 3.6 and Figure 3.9 for the correct frame size. 1. The lower frame (1) comes with the outer support arms (2) bolted in place. Cut the zip tie (3) that is used to secure the support arms for shipping and swing them into place as shown in Figure a. Australia only: Remove the 1/2 x 4 bolt from the drive belt side of the frame (4). Place the bracket (See Figure 3.32, item (6)) on top of the frame, then replace the bolt and nut. Do not tighten, as some adjustment to the bracket may be necessary later. Refer to Figure Make sure the lower frame (1) and axle (4) are arranged properly. The center crossmember (5) on the lower frame and the double tabs (6) on the axle should be facing up. The gussets (9) on the single tabs under the axle should R1 25

26 3. ASSEMBLY WHEATHEART - BH AUGERS 3.4. FRAME ASSEMBLY be closest to the lower frame (1) and intake end of the auger. Refer to Figure Center the lower frame on the axle as shown in. Bolt the lower frame to the axle using four 1/2 u-bolts that fit 2-1/2 square tubing (7) and 1/2 locknuts (8) as shown in Figure The u-bolts for the outer support arms should be to the inside of the lift arm tabs on the axle. Table 3.6 Model BH 836, BH 1036 BH 841, BH 1041 BH 846 BH 851 X 107" (2.72 m) 122" (3.10 m) 137" (3.48 m) 152" (3.89 m) Figure 3.9 Figure 3.10 Lower Frame (Top View) R1

27 WHEATHEART - BH AUGERS 3. ASSEMBLY 3.4. FRAME ASSEMBLY Figure 3.11 Lower Frame on Axle (Top View) Figure LIFT ARM ASSEMBLY ALL AUGERS See Table 3.7 and Figure 3.13 for the correct lift arm size. 1. Place stands (1) under the lower frame (2) and axle (4) as shown in Figure Bolt the lift arms (3) to the axle (4) using two 3/4 x 2-1/2 bolts (5) and 3/4 locknuts (6). Refer to Figure R1 27

28 3. ASSEMBLY WHEATHEART - BH AUGERS 3.4. FRAME ASSEMBLY Table 3.7 Model BH 836, BH 1036 BH 841, BH 1041 BH 846 BH 851 W 141" (3.58 m) 164-1/2 (4.17 m) 188" (4.78 m) 212" (5.38 m) Figure 3.13 Figure R1

29 WHEATHEART - BH AUGERS 3. ASSEMBLY 3.4. FRAME ASSEMBLY TIRE ASSEMBLY ALL AUGERS SEE FIGURE Install 15 tires (1) on rims (2) provided. Inflate to 24 psi (165 kpa), depending on size of the auger. Do not exceed the maximum recommended tire pressure for the tire. 2. Mount wheels to hubs (3) using four 1/2 x 1 1/4 wheel bolts (4) per tire. Before mounting the wheels, check to make sure the hub and wheel mounting surfaces are free from rust and debris. Finger tighten the wheel bolts and verify that the wheel is sitting flush on the hub. Torque the wheel bolts to 80 ft-lb ±10 ft-lb (108.5 Nm, ± 13.5 Nm) of torque while using the pattern shown below. WARNING Only properly trained individuals with the proper equipment should attempt to mount the tires as serious injury or death could result R1 29

30 3. ASSEMBLY WHEATHEART - BH AUGERS 3.4. FRAME ASSEMBLY Figure ATTACHING TO TUBE ALL AUGERS Important: Refer to Figure 3.17 for following instructions. 1. Remove the stand from the intake end of the auger tube and raise the discharge end with a block and tackle or a front end loader and a strong sling or chain as shown in Figure Height should be sufficient so the frame can be positioned under the tube and the lift arms can be easily attached to the track shoe. Be sure to use proper hoisting equipment and procedures and ensure sling is secured in position. Lock out the hoist apparatus before working around or under the raised tube. 2. Position the frame under the tube assembly. 3. Align the lift arms (1) and the track shoe (2) and attach using a 3/4 x 6-1/2 bolt (3) and 3/4 locknut (4). DO NOT over-tighten. Tighten snug only, this bolt acts as a pivot point. 4. Raise the discharge so the lower frame arms (5) can be aligned with the pivot bushings (6) on the welded bracket on the tube. 5. Remove the 1/2 x 1 bolts (7), 1/2 lock washers (8), 1/2 flat washers (9) and 1 flat washers (10) that are securing the cable anchor brackets in place. DO NOT remove the cable anchors. 6. Attach the lower frame to the pivot bracket and replace the washers and bolts R1

31 WHEATHEART - BH AUGERS 3. ASSEMBLY 3.4. FRAME ASSEMBLY The frame arms may need to be spread apart to fit onto the pivot bushings. It might be possible to spread them by hand; if not, a pry bar might be required. Figure 3.16 Figure CROSS MEMBER / CABLE PULLEY ASSEMBLY Refer to Figure 3.18 for following instructions. CURRENT AUGERS - BH 841, BH 1041, BH 846, BH Attach pulley mount (20) to auger tabs (21) with 1/2 x 1-1/2 bolts (19) and locknuts (21). 2. BH 851 only - Attach the lift arm x-support (1) by sliding it up between the lift arms (2) until it makes firm contact on both sides. Bolt the cross support in place with two 1/2 u-bolts that fit 2-1/2 square tubing (3) and 1/2 locknuts (4) R1 31

32 3. ASSEMBLY WHEATHEART - BH AUGERS 3.4. FRAME ASSEMBLY 2007 AND OLDER AUGERS - BH 841, BH 1041, BH 846, BH Assemble the cable idler by sliding the cable pulley (5) onto the 1/2 x 2-1/2 bolt (6) with a pulley mount strap (7) on each side and 1/2 flat washers (8) as spacers. Secure the assembly with a 1/2 locknut (9). DO NOT over-tighten. The pulley must rotate. 2. Secure a 5/8 eyebolt (10) to the pulley mount strap with a 1/2 x 2 bolt (11) and 1/2 locknut (12). DO NOT over-tighten. The straps and eyebolt must rotate. 3. Install the cable pulley mount (13) to the lower frame arms with two 1/2 x 4 bolts (14) and 1/2 locknuts (15) using 1/2 flat washers (16) as spacers. DO NOT over-tighten. The cable pulley mount must pivot. 4. Attach the cable return assembly to the cable pulley mount by sliding the eyebolt (10) through the hole (17) and securing with a 5/8 locknut (18). Tighten, then loosen the nut enough to let the eyebolt turn freely. 5. BH 851only - Attach the lift arm x-support (1) by sliding it up between the lift arms (2) until it makes firm contact on both sides. Bolt the cross-support in place with two 1/2 u-bolts that fit 2-1/2 square tubing (3) and 1/2 locknuts (4) AND OLDER CURRENT Figure R1

33 WHEATHEART - BH AUGERS 3. ASSEMBLY 3.4. FRAME ASSEMBLY HAND WINCH & IDLER ASSEMBLY ALL AUGERS Steps 1-5 are for North America only: 1. Locate the mounting bracket 36 (66 cm) from the lower frame arm pivot as shown in Figure Attach the mounting bracket (6) to the lower frame arm (9) using a 3/8 u-bolt to fit a 2-1/2 HSS (10), 3/8 flat washers (11) and 3/8 locknuts (12). DO NOT tighten. Refer to Figure Install both belts on gearbox pulley. Take the idler pulley (1) and place it under the back of both belts at point 21 as shown in Figure Assemble the idler by attaching the flush side of the idler pulley (1) to the idler guard (2) with a 1/2 x 2-1/2 bolt (3) and 1/2 locknut (4) using a 1/2 flat washer (5) as a spacer. DO NOT overtighten. Pulley must rotate freely (see Figure 3.20). Idler used on BH 841, 846, 851, and 1041 only. 5. Secure the pulley and guard assembly to the mounting bracket (6) using two 3/8 x 1 bolts (7) and 3/8 locknuts Figure 3.19 (8). Align the mounting bracket so that the idler pulley lines up with the gearbox pulley and tighten. Refer to Figure Assemble the winch (13) and mount plate (14) together with three 3/8 x 1-1/4 bolts (15), 3/8 flat washers (16) and 3/8 locknuts (17) as shown in Figure Locate the winch assembly 14 (35.5 cm) from the cross member to the center of the winch drum as shown in Figure 3.20 (BH 836, BH 1036) or 3.19 (BH 841, BH1041, BH 846, BH 851). 8. Loosely secure the winch assembly to the lower frame arm (18) using two 3/8 u-bolts to fit 2 1/2 square tubing (19) and 3/8 locknuts (20) as shown in Figure Release the coiled winch cable from the tube. Thread it down around the cable idler from the top (BH 841, BH 1041, BH 846, BH 851only) and attach it to the winch drum as shown in Figure Align the winch assembly with the roller in the track shoe set screw (36 ), or with the cable idler (BH 841, BH 1041, BH 846, BH 851) so that the cable will index properly on the winch drum when lifting the auger. Secure by tightening nuts (20). Make sure there is a minimum of three wraps on the winch drum when the auger is in the transport position R1 33

34 3. ASSEMBLY WHEATHEART - BH AUGERS 3.4. FRAME ASSEMBLY Figure R1

35 WHEATHEART - BH AUGERS 3.5. DRIVE ASSEMBLY 3. ASSEMBLY 3.5. DRIVE ASSEMBLY The following figures and tables apply to the gas, electric, and PTO drive assemblies. BH 836 PTO/ELEC BH 1036 PTO/ELEC BH 836 GAS BH 1036 GAS BH 841 PTO/ELEC BH 1041 PTO/ELEC BH 841GAS BH 1041 GAS BH 846 GAS BH 851 GAS BH 846 PTO/ELEC BH 851 PTO/ELEC Figure 3.21 Motor Mount Bracket Positions R1 35

36 3. ASSEMBLY WHEATHEART - BH AUGERS 3.5. DRIVE ASSEMBLY Figure 3.22 Table 3.8 Model Onan 20 Onan 24 BH 8 x 36 BH 8 x 41 BH 8 x 46 BH 8 x 51 BH 10 x 36 BH 10 x /4 (2.29 m) 105-1/4 (2.67 m) 120-1/4 (3.05 m) 135-1/4 (3.44 m) n/a 100 (2.54 m) 91-1/4 (2.32 m) 105-1/4 (2.67 m) 121-1/4 (3.08 m) 136-1/4 (3.46 m) 88-1/4 (2.24 m) 100 (2.54 m) V Kohler/Briggs & Stratton 90-3/8 (2.30 m) 105-3/8 (2.68 m) 121 (3.07 m) 135-3/8 (3.44 m) 88-1/4 (2.24 m) 100 (2.54 m) Honda/Robin 89-7/8 (2.28 m) 104-7/8 (2.66 m) 119-7/8 (3.04 m) 134-7/8 (3.50 m) 87-3/4 (2.23 m) 100 (2.54 m) PTO/Electric 87-3/8 (2.23 m) 102-3/8 (2.06 m) 117-3/8 (2.98 m) 132-3/8 (3.36 m) 85 (2.16 m) 97-1/4 (2.47 m) Figure GAS ENGINE & COMPONENTS Refer to Figure 3.25 (and additional figures and tables where mentioned) for following instructions. ALL AUGERS A double-groove 15 sheave is used on the gearbox for gas engines; see item (46) in Figure R1

37 WHEATHEART - BH AUGERS 3. ASSEMBLY 3.5. DRIVE ASSEMBLY 1. Slide the bracket (1) onto the over-center handle (2) attached to the motor mount bracket (3). 2. Bolt the brackets to the lower frame arms (4) with four 7/16 x 3-1/2 carriage bolts (5) and 7/16 locknuts (6). Locate the brackets in the proper holes indicated by the arrows in Figure Set the length of the leveler bar (7) for the engine specified in Table 3.8. Adjust the nut (8) to change the length. See Figure Attach the leveler bar to the pivot bracket tab (9) with a 1/2 x 1-3/4 bolt (10) and 1/2 locknut (11). 5. Locate the proper hole in the motor mount for the engine specified in Table 3.9 and Figure Secure the leveler bar (7) to the proper hole with a 1/2 x 1-3/4 bolt (12) and 1/2 locknut (13). Table 3.9 Model Onan 20 Onan 24 Kohler/ Briggs & Stratton ALL AUGERS B A B,C a a. Use hole B for BH 846 augers, and hole C for all other augers. Honda/ Robin 7. Attach the motor pulley guard mount (14) to the motor mount with two 3/8 x 1 bolts (15), 3/8 locknuts (16), and four 3/8 flat washers (17). Do not tighten. 8. North America only: Secure the motor pulley guard (18) to the motor pulley guard mount with two 3/8 x 1 bolts (19), 3/8 flat washers (20), and 3/8 locknuts (21). Do not tighten. 9. Place the gas motor mounts (22) on top of the motor mount and orient them as shown in Figure 3.24 and Place the battery mount (23) under the motor mount and secure the 3 items together with four 3/8 x 1-1/2 bolts (24), 3/8 flat washers (25), and 3/8 locknuts (26). Do not tighten. When attaching the battery mount, use the first set of holes and slots closest to the battery holder (27). Different holes may be used depending on the space required for different features of the engine or options on the auger (muffler, mover kit, etc.). 10. Slide the pulley (28) on the engine s output shaft using a key (29). Tighten the set screw (30) on the pulley once the end of the shaft is flush with the pulley hub. All engines use a double-groove 4 x 1-1/8 pulley except for the Honda engine, which uses a 4 x 1 pulley. 11. Place the engine on the gas motor mounts and secure in place with four 3/8 x 1-3/4 bolts (31), 3/8 locknuts (32), and eight 3/8 flat washers (33). Do not tighten. 12. North America only: Align the engine pulley (46) and gearbox pulley (28) so the v-belts will run straight. Once the pulleys are aligned, tighten the 4 bolts (31) and nuts (32). Check the alignment of the idler pulley and adjust if necessary. C R1 37

38 3. ASSEMBLY WHEATHEART - BH AUGERS 3.5. DRIVE ASSEMBLY 13. Australia only: Slide the engine away from the motor mount bracket (3) until the center of the web between the 2 grooves on the pulley (46) is 2-1/8 from the edge of the bracket. Tighten the 4 bolts (31) and nuts (32). Steps are for North America only: 14. Install the v-belts (47) on the pulleys (28, 46); refer to Table 3.10 for belt size and center-to-center distance. Table 3.10 PULLEY CENTER-CENTER Model V-BELT SIZE DISTANCE BH 836, BH 1036 B /4 (230.5 cm) BH 841, BH 1041 B /4 (271 cm) BH 846 B /4 (308 cm) BH 851 B /2 (344cm) 15. Using the over-center handle (2), place the motor mount (3) in its working position. Slide the engine towards the discharge until the required center-tocenter distance between the engine and gearbox pulleys is obtained. This will ensure proper tension in the belt.tighten the 4 bolts (24) and nuts (26) to secure the engine. 16. Adjust the height, front-to-back, and side-to-side position of the motor pulley guard so the hole in the center of the motor pulley guard (34) is in the center of the pulley shaft. The guard must be less than 1 from the engine. 17. Tighten the 2 bolts (19) and nuts (21) on the motor pulley guard to secure the height of the guard. Tighten the 2 bolts (15) and nuts (16) on the motor pulley guard mount to secure the front-to-back and side-to-side position of the guard. 18. Space the tank mount brackets (35) as shown in Figure Attach the brackets using two 3/8 u-bolts to fit 2-1/2 square tube (36), and four 3/8 locknuts (37). Figure Place the gas tank (38) on the brackets and strap it in place using two gear clamps (39). 20. Attach the one end of the 1/4 x 3 hose (40) to the gas tank using a 1/4 hose clamp (41), and attach the other end of the hose to the engine using another 1/4 hose clamp (42). 21. Secure the battery (43) in the battery mount (27) using a 1/4 u-bolt that will fit the battery (44), and two 1/4 locknuts (45) R1

39 WHEATHEART - BH AUGERS 3. ASSEMBLY 3.5. DRIVE ASSEMBLY Figure ELECTRIC MOTOR & COMPONENTS Refer to Figure 3.26 (and additional figures and tables where mentioned) for following instructions. ALL AUGERS A double-groove 15 sheave is used on the gearbox for electric motors; see item (46) in Figure Slide the bracket (1) onto the over-center handle (2) attached to the motor mount bracket (3). 2. Bolt the brackets to the lower frame arms (4) with four 7/16 x 3-1/2 carriage bolts (5) and 7/16 locknuts (6). Locate the brackets in the proper holes indicated by the arrows in Figure Set the length of the leveler bar (7) for the electric motor specified in Table 3.8. Adjust the nut (8) to change the length. See Figure Attach the leveler bar to the pivot bracket tab (9) with a 1/2 x 1-3/4 bolt (10) and 1/2 locknut (11). 5. Locate the proper hole in the motor mount as specified in Figure R1 39

40 3. ASSEMBLY WHEATHEART - BH AUGERS 3.5. DRIVE ASSEMBLY 6. Secure the leveler bar (7) to the proper hole with a 1/2 x 1-3/4 bolt (12) and 1/2 locknut (13). 7. Attach the motor pulley guard mount (14) to the motor mount with two 3/8 x 1 bolts (15), 3/8 locknuts (16), and four 3/8 flat washers (17). Do not tighten. 8. Secure the motor pulley guard (18) to the motor pulley guard mount with two 3/8 x 1 bolts (19), 3/8 flat washers (20), and 3/8 locknuts (21). Do not tighten. 9. Place the electric motor mounts (22) on top of the motor mount and orient them as shown in Figure Secure with four 3/8 x 1 bolts (24), 3/8 flat washers (25), and 3/8 locknuts (26). Do not tighten. 10. Slide the pulley (28) on to the motor s output shaft using a key (29). Tighten the set screw (30) on the pulley once the end of the shaft is flush with the pulley face. All electric motors use a double-groove 8 pulley. 11. Place the motor on the electric motor mounts and secure it in place with four 3/8 x 1 bolts (31), 3/8 locknuts (32), and eight 3/8 flat washers (33). Do not tighten. 12. Align the electric motor pulley (28)and the gearbox pulley (46) so the v-belts will run straight. Once the pulleys are aligned, tighten the 4 bolts (31) and nuts (32). Check alignment of the idler and pulley, and adjust if necessary. 13. Install the v-belts (47) on the pulleys (28,46); refer to Table 3.11 for belt size. Table 3.11 Model V-BELT SIZE BH 836, BH 1036 B210 BH 841, BH 1041 B240 BH 846 B270 BH 851 B Slide the electric motor towards the discharge so there is adequate tension on the belt when the motor is engaged using the over-center handle. Tighten the 4 bolts (24) and nuts (26) to secure the motor. 15. Adjust the height, front-to-back, and side-to-side position of the motor pulley guard so the hole in the center of the motor pulley guard (34) is in the center of the pulley shaft. The guard must be less than 1 from the motor. 16. Tighten the 2 bolts (19) and nuts (21) on the motor pulley guard to secure the height of the guard. Tighten the 2 bolts (15) and nuts (16) on the motor pulley guard mount to secure the front-to-back and side-to-side position of the guard R1

41 WHEATHEART - BH AUGERS 3. ASSEMBLY 3.5. DRIVE ASSEMBLY Figure PTO & COMPONENTS Refer to Figure 3.27 (and additional figures and tables where mentioned) for following instructions. ALL AUGERS A double-groove 8 sheave is used on the gearbox for PTO driven augers; see item (47) in Figure Slide the bracket (1) onto the over-center handle (2) attached to the motor mount bracket (3). 2. Bolt the brackets to the lower frame arms (4) with four 7/16 x 3-1/2 carriage bolts (5) and 7/16 locknuts (6). Locate the brackets in the proper holes indicated by the arrows in Figure Set the length of the leveler bar (7) for a PTO driven auger as specified in Table 3.8. Adjust the nut (8) to change the length. See Figure Attach the leveler bar to the pivot bracket tab (9) with a 1/2 x 1-3/4 bolt (10) and 1/2 locknut (11). 4. Use hole B or C in Figure 3.23 to mount the leveler bar to the motor mount (use hole B for 8-46 augers, and hole C for all other augers). 5. Secure the leveler bar (7) to the proper hole with a 1/2 x 1-3/4 bolt (12) and 1/2 locknut (13) R1 41

42 3. ASSEMBLY WHEATHEART - BH AUGERS 3.5. DRIVE ASSEMBLY 6. Attach the PTO mount (14) to the motor mount with four 3/8 x 1 bolts (15), 3/8 locknuts (16), and 3/8 flat washers (17). Do not tighten. 7. Slide the 2 pillow block assemblies (18) onto the jackshaft (19) with the locking collars facing in. Slide the jackshaft through the hole in the PTO mount (20), and secure the pillow blocks to the PTO mount with four 1/2 x 1-1/2 bolts (21), 1/2 flat washers (22), and 1/2 locknuts (23). 8. Slide the pulley (24) on to the jackshaft with a key (25) using the inside groove (26). Do not tighten. All PTO driven augers use a double groove 15 x 1 pulley. 9. Align the PTO pulley (24) with the gearbox pulley(47) so the belts will run straight. Adjust both the jackshaft s position in the pillow blocks and the pulley s position on the jackshaft to properly align. Tighten both locking collars on the pillow blocks and the set screw (27) on the pulley. 10. Secure the PTO shaft shield (28) in place with two 1/2 x 1 bolts (29) and 1/2 locknuts (30). 11. Install the v-belts (46) on the pulleys (24,47). Refer to Table 3.12 for belt size. Check alignment of the idler and pulley, and adjust if necessary. Table 3.12 Model V-BELT SIZE BH 836, BH 1036 B210 BH 841, BH 1041 B240 BH 846 B270 BH 851 B Slide the PTO mount towards the discharge so there is adequate tension on the belt when the PTO is engaged using the over-center handle. Tighten the 4 bolts (15) and nuts (16) to secure the PTO. 13. Bolt the PTO front shield (31) to the PTO mount using four 3/8 x 3/4 bolts (32) and 3/8 lock washers (33). 14. Install the PTO rubber flap (34) onto the PTO front shield with the PTO rubber mount strap (35), two 5/16 x 3/4 bolts (36), and 5/16 locknuts (37). 15. Secure the PTO transport saddle (38) to the lower frame arms with a 3/8 u- bolt that fits 2-1/2 HSS (39) and two 3/8 locknuts (40). For 36 augers, measure 16-1/2 from cross plate edge to center of u-bolt. This measurement is not critical for other augers. 16. Install the 60 PTO driveline (41) onto the jackshaft with a key (42), and tighten the set screw to secure (43). 17. Place the driveline in the transport saddle and secure it with the PTO pin (44) and hairpin (45) R1

43 WHEATHEART - BH AUGERS 3. ASSEMBLY 3.5. DRIVE ASSEMBLY Figure AUSTRALIAN BELT GUARD ASSEMBLY AUSTRALIAN GAS DRIVE AUGERS See Table 3.13 and Figure 3.28 and 3.29 for the lower guard assembly. 1. Place the u-bolt half pivot arm (10) through the pipe on the engine end mount (4) and tighten the nut until it bottoms out, leaving the arm free to pivot. Mount the engine end mount guard (4) onto the motor pulley guard (1) using two 3/8 x 1 bolts (15), locknuts, and washers. The hole in the center of the engine end mount (4) should be lined up with the center of the slot in the motor pulley guard mount (1) and the same vertical height as the engine shaft. 2. Using two 1/4 x 5/8 self-tapping screws, mount the engine side cover plate (7) to the engine end mount guard (4). Slide the engine side cover plate (7) as close to the engine as possible. DO NOT over-tighten screws. 3. Fasten the engine side pivot (8) on the inside of the outer engine side guard (5) using two 1/4 x 5/8 self-tapping screws R1 43

44 3. ASSEMBLY WHEATHEART - BH AUGERS 3.5. DRIVE ASSEMBLY 4. Attach the outer engine side guard (5) to the inner engine side guard (6) using four 1/4 x 5/8 self-tapping screws. Figure 3.28 Lower Belt Guard Assembly Figure 3.29 Table 3.13 Lower Belt Guard Parts ITEM Part No. Description QTY MOTOR PULLEY GUARD MOUNT ENGINE MT Z BRACKET, DISCHARGE SIDE ENGINE MOUNT Z BRACKET, INTAKE SIDE ENGINE END MOUNT ENGINE SIDE GUARD, OUTER ENGINE SIDE GUARD, INNER ENGINE SIDE COVER PLATE ENGINE SIDE PIVOT U-BOLT HALF PIVOT ARM HINGE GA x 2 x 3 PLATE RUBBER SAFETY STRAP, 2-1/2, SINGLE RUBBER STRAP CATCH BOLT PACKAGE 1 Bolt package is for both the lower and upper guard assembly R1

45 WHEATHEART - BH AUGERS 3. ASSEMBLY 3.5. DRIVE ASSEMBLY 5. From the bolt package, assemble the 2 hinge (11), the 2 x 3 galvanized plate (12), and the rubber strap (13) using four #10-24 x 1/2 bolts and lock nuts. Bend the cotter pin over to retain rubber strap. Mount the assembled piece to the inner engine side guard (6) using two 1/4 x 5/8 self-tapping screws. Mount the catch (14) for the rubber strap on the outer side guard (5) with two 1/4 x 5/8 self-tapping screws. See Figure 3.28 and While holding the lower guard assembly (5, 6), vertical slide the engine side pivot (8) onto the half pivot arm (10). Swing the assembly to the side and rest on the tire to facilitate the upper guard assembly. See Table 3.14 and Figure 3.31 and 3.32 for the upper guard assembly. 7. BH 836 Model Only: Attach the two 3/16 plates (7) to the inside of the linkage mount (6) with the threaded rod facing out. Fasten with two 3/8 locknuts, leaving linkage loose enough to pivot. 8. All Other Models: Attach the two 3/16 plates (7) to the inside of the linkage mount (6) using two 3/8 x 1 bolts (14) and nuts. The bolts should be loose enough to allow the plates to pivot. 9. Place gearbox mount plate (5) through the inner gearbox guard (2). Fasten it using four 1/4 x 5/8 self-tapping screws (13). 10. Place end of inner belt guard (2) with gearbox mount plate (5) onto gearbox housing. 11. Place gearbox mount bracket (4) onto the capped side of the gearbox. Attach the other end of the bracket to the inner belt guard shield (2) using a 3/8 x 1 bolt and nut. 12. Using a 3/8 x 1 bolt (15) and nut, attach the lower end of the inner guard (2) to the inside linkage plate (7 or 7*) with the bolt facing outward and loose enough to allow the linkage to pivot. 13. Install the sheave with the long hub facing inward and tighten set screws. The sheave will not sit flush with the shaft. Front View Rear View Figure 3.30 Front and Rear Views of Latch Assembly Remaining parts will be in the bolt package. If the idler is not recessed on one side, the 2-7/8 spacer may need to have 5/32 (4 mm) of its length removed. Steps and 19. are excluded for BH 836 and BH 1036 augers. 14. Insert the 1/2 x 5-1/2 bolt (11) partially through the inner belt guard shield (2) as shown in Figure R1 45

46 3. ASSEMBLY WHEATHEART - BH AUGERS 3.5. DRIVE ASSEMBLY Table 3.14 Upper Belt Guard Parts Item Part No. Description QTY OUTER GEARBOX BELT GUARD INNER GEARBOX BELT GUARD GEARBOX INTAKE END COVER GEARBOX MOUNT BRACKET GEARBOX MOUNT PLATE LINKAGE MOUNT /16 LINKAGE PLATE (EXCLUDING 8 x 36 MODELS) 2 7* /16 LINKAGE PLATE (8 x 36 MODELS ONLY) /8 SPACER /8 SPACER /2 X 5-1/2 GR5 BOLT /2 UNC GR5 NYLOCK NUT IDLER Place the 3/8 spacer (8) on the 1/2 bolt (11). Then insert the idler (12) followed by the 2-7/8 spacer (9). The idler must be recessed on the 2-7/8 bushing side as shown in Figure Install the belts onto the gearbox and engine pulleys, running on top of the idler. It may be necessary to over-center the motor mount to install the belts. See Table 3.10 for belt size and center-to-center distances (when engine over-center is in working position). Adjust engine position by sliding the engine mount Z-brackets. This will ensure proper belt tension. Tighten bolts. The BH 836 and BH 1036 augers do not have an idler. 17. Referring to Figure 3.28, adjust the motor pulley guard mount (1) so that the outside face is 5-7/8 (14.9 cm) away from the motor mount bracket (9) face and that the center slot is aligned horizontally with the shaft center on the engine. Tighten bolts. 18. Attach the outer belt guard (1) to the inner belt guard (2) by first inserting the top 1/4 x 5/8 self-tapping screw nearest the discharge end. Repeat for the top hole nearest the intake end. Do not insert the remaining screws. Refer to Figure Push the 1/2 bolt (11) the remainder of the way through the outer guard and tighten using the 1/2 nylock nut (10). See Figure Insert the remaining 1/4 x 5/8 self-tapping screws into the guard assembly. 21. Attach the outer belt guard (1) to the other 3/16 plate (7 or 7*) with a 3/8 x 1 bolt (16) and nut. DO NOT over-tighten, leaving the assembly free to pivot as shown in Figure Attach the intake end gearbox belt cover (3) using four 1/4 x 5/8 selftapping screws as shown in Figure Re-install the lower guard assembly over the upper guard and latch the rubber strap to secure R1

MK AUGERS POWER SWING KIT ASSEMBLY & OPERATION MANUAL

MK AUGERS POWER SWING KIT ASSEMBLY & OPERATION MANUAL MK AUGERS POWER SWING KIT ASSEMBLY & OPERATION MANUAL Read this manual before using product. Failure to follow instructions and safety precautions can result in serious injury, death, or property damage.

More information

INTAKE HOPPER STX/TF/TFX/WR AUGERS OPERATOR AND ASSEMBLY MANUAL

INTAKE HOPPER STX/TF/TFX/WR AUGERS OPERATOR AND ASSEMBLY MANUAL INTAKE HOPPER STX/TF/TFX/WR AUGERS OPERATOR AND ASSEMBLY MANUAL Read this manual before using product. Failure to follow instructions and safety precautions can result in serious injury, death, or property

More information

MK FLEX AUGER ASSEMBLY & OPERATION MANUAL

MK FLEX AUGER ASSEMBLY & OPERATION MANUAL MK FLEX AUGER 71-111 ASSEMBLY & OPERATION MANUAL Read this manual before using product. Failure to follow instructions and safety precautions can result in serious injury, death, or property damage. Keep

More information

GRAIN CONVEYOR S-DRIVE

GRAIN CONVEYOR S-DRIVE GRAIN CONVEYOR S-DRIVE 55-100 1300 P / 1500 P SERIES ASSEMBLY MANUAL Read this manual before using product. Failure to follow instructions and safety precautions can result in serious injury, death, or

More information

GRAIN AUGER EMD GHR 80 X & 100 X ASSEMBLY & OPERATION MANUAL

GRAIN AUGER EMD GHR 80 X & 100 X ASSEMBLY & OPERATION MANUAL GRAIN AUGER EMD ASSEMBLY & OPERATION MANUAL Read this manual before using product. Failure to follow instructions and safety precautions can result in serious injury, death, or property damage. Keep manual

More information

GRAIN AUGERS WR 60/80/100 X EMD MODEL ASSEMBLY & OPERATION MANUAL

GRAIN AUGERS WR 60/80/100 X EMD MODEL ASSEMBLY & OPERATION MANUAL GRAIN AUGERS ASSEMBLY & OPERATION MANUAL WR EMD Augers covered in this manual: 60-26, 60-31, 60-36, 60-41, 60-51, 60-61 80-26, 80-31, 80-36, 80-41, 80-46, 80-51, 80-56, 80-61, 80-71 10-31, 10-41, 10-51,

More information

GRAIN AUGERS WR PTO-SD ASSEMBLY & OPERATION MANUAL

GRAIN AUGERS WR PTO-SD ASSEMBLY & OPERATION MANUAL GRAIN AUGERS WR PTO-SD ASSEMBLY & OPERATION MANUAL Read this manual before using product. Failure to follow instructions and safety precautions can result in serious injury, death, or property damage.

More information

GRAIN AUGER WR 60/80 X PTO-BD MODELS ASSEMBLY & OPERATION MANUAL

GRAIN AUGER WR 60/80 X PTO-BD MODELS ASSEMBLY & OPERATION MANUAL GRAIN AUGER ASSEMBLY & OPERATION MANUAL ORIGINAL INSTRUCTIONS WR PTO-BD Augers covered in this manual: 60-36, 60-41 80-36, 80-41, 80-46, 80-51 Read this manual before using product. Failure to follow instructions

More information

GRAIN AUGERS MK 80/100 X ASSEMBLY & OPERATION MANUAL

GRAIN AUGERS MK 80/100 X ASSEMBLY & OPERATION MANUAL GRAIN AUGERS ASSEMBLY & OPERATION MANUAL Read this manual before using product. Failure to follow instructions and safety precautions can result in serious injury, death, or property damage. Keep manual

More information

A1062 & A1072 AUGER ASSEMBLY MANUAL. Read & understand all instructions pertaining to this auger prior to use!

A1062 & A1072 AUGER ASSEMBLY MANUAL. Read & understand all instructions pertaining to this auger prior to use! A1062 & A1072 AUGER ASSEMBLY MANUAL Read & understand all instructions pertaining to this auger prior to use! Safety Alert Watch for this ALERT Symbol. It identifies potential hazards to Personal SAFETY

More information

CALF SHELTER 6, 12, 15, 18, & 24 MODELS ASSEMBLY MANUAL

CALF SHELTER 6, 12, 15, 18, & 24 MODELS ASSEMBLY MANUAL CALF SHELTER 6, 12, 15, 18, & 24 MODELS ASSEMBLY MANUAL Read this manual before using product. Failure to follow instructions and safety precautions can result in serious injury, death, or property damage.

More information

MKX100-SERIES GRAIN AUGERS MKX100-53/63/73/83 ASSEMBLY & OPERATION

MKX100-SERIES GRAIN AUGERS MKX100-53/63/73/83 ASSEMBLY & OPERATION MKX100-SERIES GRAIN AUGERS ASSEMBLY & OPERATION ORIGINAL INSTRUCTIONS Read this manual before using product. Failure to follow instructions and safety precautions can result in serious injury, death, or

More information

GHR130 GRAIN AUGERS 41 PTO-SD & EMD MODELS ASSEMBLY & OPERATION MANUAL

GHR130 GRAIN AUGERS 41 PTO-SD & EMD MODELS ASSEMBLY & OPERATION MANUAL GHR130 GRAIN AUGERS 41 ASSEMBLY & OPERATION MANUAL ORIGINAL INSTRUCTIONS Read this manual before using product. Failure to follow instructions and safety precautions can result in serious injury, death,

More information

GRAIN AUGERS MK80 X ASSEMBLY & OPERATION MANUAL

GRAIN AUGERS MK80 X ASSEMBLY & OPERATION MANUAL GRAIN AUGERS ASSEMBLY & OPERATION MANUAL ORIGINAL INSTRUCTIONS Read this manual before using product. Failure to follow instructions and safety precautions can result in serious injury, death, or property

More information

Operator s Manual and Assembly

Operator s Manual and Assembly Operator s Manual and Assembly Published: Mar 24, 2017 Manual Part No. AH02-00-MAN Gatco Manufacturing Inc. www.gatcomfg.com Location: 2524 South Service Road West, Swift Current, SK, Canada Mail: Box

More information

X-SERIES 13" AUGERS X130-74, X130-84, X ASSEMBLY AND OPERATION MANUAL

X-SERIES 13 AUGERS X130-74, X130-84, X ASSEMBLY AND OPERATION MANUAL X-SERIES 13" AUGERS ASSEMBLY AND OPERATION MANUAL ORIGINAL INSTRUCTIONS Read this manual before using product. Failure to follow instructions and safety precautions can result in serious injury, death,

More information

CAM-LIFT WHEEL MOVE KIT 1500-SERIES S-DRIVE STANDARD CONVEYORS ASSEMBLY MANUAL

CAM-LIFT WHEEL MOVE KIT 1500-SERIES S-DRIVE STANDARD CONVEYORS ASSEMBLY MANUAL CAM-LIFT WHEEL MOVE KIT ASSEMBLY MANUAL This manual applies to the following models: 1565, 1575, 1585, 1590, 15100 ORIGINAL INSTRUCTIONS Read this manual before using product. Failure to follow instructions

More information

GHR130 GRAIN AUGERS - 51,61,71 PTO-SD MODEL ASSEMBLY & OPERATION MANUAL

GHR130 GRAIN AUGERS - 51,61,71 PTO-SD MODEL ASSEMBLY & OPERATION MANUAL GHR130 GRAIN AUGERS - 51,61,71 ASSEMBLY & OPERATION MANUAL ORIGINAL INSTRUCTIONS Read this manual before using product. Failure to follow instructions and safety precautions can result in serious injury,

More information

Portable Grain Belt Conveyor

Portable Grain Belt Conveyor Portable Grain Belt Conveyor Top Drive Assembly Manual This manual applies to: 1300 Series: 1330TD, 1335TD, 1340TD, 1345TD 1500 Series: 1530TD, 1535TD, 1540TD, 1545TD Original Instructions Read this manual

More information

4" UTILITY GRAIN AUGERS

4 UTILITY GRAIN AUGERS 4" UTILITY GRAIN AUGERS OPERATION & ASSEMBLY MANUAL Read this manual before using product. Failure to follow instructions and safety precautions can result in serious injury, death, or property damage.

More information

Portable Grain Belt Conveyor

Portable Grain Belt Conveyor Portable Grain Belt Conveyor Field Loader Top Drive Assembly Manual This manual applies to: 1300 Series: 1335FLTD, 1345FLTD 1500 Series: FX1535FLTD, FX1545FLTD Original Instructions Read this manual before

More information

GRAIN AUGERS W & 36 PTO-SD & EMD OPERATION & ASSEMBLY

GRAIN AUGERS W & 36 PTO-SD & EMD OPERATION & ASSEMBLY GRAIN AUGERS W130-31 & 36 PTO-SD & EMD OPERATION & ASSEMBLY Read this manual before using product. Failure to follow instructions and safety precautions can result in serious injury, death, or property

More information

GROUNDSMASTER. 52 Recycler. for 120 Traction Unit. Model No & UP. Operator s Manual

GROUNDSMASTER. 52 Recycler. for 120 Traction Unit. Model No & UP. Operator s Manual FORM NO. 8-980 Rev A GROUNDSMASTER 5 Recycler for 0 Traction Unit Model No. 077 79000 & UP Operator s Manual IMPORTANT: Read this manual carefully. It contains information about your safety and the safety

More information

T832 T842 ELECTRIC MOTOR OPTION ASSEMBLY MANUAL. Read & understand all instructions pertaining to this option prior to use!

T832 T842 ELECTRIC MOTOR OPTION ASSEMBLY MANUAL. Read & understand all instructions pertaining to this option prior to use! T832 T842 ELECTRIC MOTOR OPTION ASSEMBLY MANUAL Read & understand all instructions pertaining to this option prior to use! Safety Alert Watch for this ALERT Symbol. It identifies potential hazards to Personal

More information

Wheel Horse. 44 Snowthrower. for 5xi Lawn and Garden Tractors. Model No & Up. Operator s Manual

Wheel Horse. 44 Snowthrower. for 5xi Lawn and Garden Tractors. Model No & Up. Operator s Manual FORM NO. 8 Rev A Wheel Horse Snowthrower for 5xi Lawn and Garden Tractors Model No. 7966 890050 & Up Operator s Manual IMPORTANT: Read this manual, and your tractor manual, carefully. They contain information

More information

TRANSFER AUGER 8, 10, & 13 ASSEMBLY & OPERATION MANUAL

TRANSFER AUGER 8, 10, & 13 ASSEMBLY & OPERATION MANUAL TRANSFER AUGER 8, 10, & 13 ASSEMBLY & OPERATION MANUAL Read this manual before using product. Failure to follow instructions and safety precautions can result in serious injury, death, or property damage.

More information

SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS ASSEMBLY & OPERATION MANUAL

SELF-PROPELLED AUGER KIT WHEATHEART & COMPETITOR MODELS ASSEMBLY & OPERATION MANUAL SELF-PROPELLED AUGER KIT ASSEMBLY & OPERATION MANUAL Read this manual before using product. Failure to follow instructions and safety precautions can result in serious injury, death, or property damage.

More information

TRANSPORT AUGER TUBE / UNDERCARRIAGE / DRIVE COMPONENTS. INDEX Section L

TRANSPORT AUGER TUBE / UNDERCARRIAGE / DRIVE COMPONENTS. INDEX Section L INDEX Section L TRANSPORT AUGER TUBE / UNDERCARRIAGE / DRIVE COMPONENTS TRANSPORT AUGER TUBE / UNDERCARRIAGE/ TF WHEEL MOVE L Description Page TF3, TF3, TF03, TF03 Basic Auger...L-3 TF, TF0 Basic Auger...L-

More information

BEFCO. Operator s Manual BABY HOP & HOP FERTILIZER SPREADERS ACCESSORIES SIDE ROW DISCHARGE. AA4-120 (fits models Hop 209 & 212) DEFLECTOR

BEFCO. Operator s Manual BABY HOP & HOP FERTILIZER SPREADERS ACCESSORIES SIDE ROW DISCHARGE. AA4-120 (fits models Hop 209 & 212) DEFLECTOR BEFCO Operator s Manual BABY HOP & HOP FERTILIZER SPREADERS ACCESSORIES SIDE ROW DISCHARGE AA-0 (fits models Hop 09 & ) DEFLECTOR AA-0 (fits models Baby Hop 0 & 06) 009-95 (fits models Hop 0 & 06) 009-968

More information

R SERIES AUGERS R8-36, R8-41, R8-46, R8-51, R10-36, R10-41, & R10-51 OPERATION MANUAL

R SERIES AUGERS R8-36, R8-41, R8-46, R8-51, R10-36, R10-41, & R10-51 OPERATION MANUAL R SERIES AUGERS OPERATION MANUAL Read this manual before using product. Failure to follow instructions and safety precautions can result in serious injury, death, or property damage. Keep manual for future

More information

Two-Stage Snow Blower For 4WD Pick Up Trucks. Operator s Manual

Two-Stage Snow Blower For 4WD Pick Up Trucks. Operator s Manual Two-Stage Snow Blower For 4WD Pick Up Trucks Operator s Manual Distrubuted by: Metal Fabricating LLC P.O. Box 831 Brodheadsville, PA 18322 Phone: 570-992-9989 SnowVac.com WARRANTY POLICY Metal Fabricating

More information

SECTION V ASSEMBLY CAUTION THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE THOROUGHLY UNDERSTOOD BEFORE ATTEMPTING MACHINE ASSEMBLY.

SECTION V ASSEMBLY CAUTION THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE THOROUGHLY UNDERSTOOD BEFORE ATTEMPTING MACHINE ASSEMBLY. SECTION V ASSEMBLY CAUTION THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE THOROUGHLY UNDERSTOOD BEFORE ATTEMPTING MACHINE ASSEMBLY. 1. Wear personal protective equipment such as, but not limited to protection

More information

SELF-PROPELLED AUGER KIT

SELF-PROPELLED AUGER KIT SELF-PROPELLED AUGER KIT ASSEMBLY & OPERATION MANUAL Read this manual before using product. Failure to follow instructions and safety precautions can result in serious injury, death, or property damage.

More information

ProLine. 44 Mower. for 120 Traction Unit. Model No & Up. Operator s Manual

ProLine. 44 Mower. for 120 Traction Unit. Model No & Up. Operator s Manual FORM NO. 9 ProLine Mower for 0 Traction Unit Model No. 05 99000 & Up Operator s Manual IMPORTANT: Read this manual carefully. It contains information about your safety and the safety of others. Also become

More information

Wheel Horse. 36 Tiller. Model No & Up. Operator s Manual

Wheel Horse. 36 Tiller. Model No & Up. Operator s Manual FORM NO. 8 9 Rev. A Wheel Horse 6 Tiller for Classic Garden Tractors Model No. 7970 690000 & Up Operator s Manual IMPORTANT: Read this manual carefully. It contains information about your safety and the

More information

Package Contents Part A (3) I-Beam (1) Base (2) Other parts

Package Contents Part A (3) I-Beam (1) Base (2) Other parts Page 1 Installation Instructions for 81245 Adjustable Height Gantry Crane 1-Ton Capacity Table of Contents Important Safety Information pg. 2 Specific Operation Warnings pg. 2 Main Parts of Product pg.

More information

Quiet Collector. Model No & Up

Quiet Collector. Model No & Up FORM NO. -8GB Rev A Quiet Collector Model No. 795-890000 & Up Operator s Manual IMPORTANT: Read this manual, and your tractor manual, carefully. They contain information about your safety and the safety

More information

WOOD CHIPPER WC1103 5PQ (8/02/12)

WOOD CHIPPER WC1103 5PQ (8/02/12) O P E R A T O R ' S M A N U A L WOOD CHIPPER WC1103 5PQ990101 (8/02/12) To the Owner; Thank-You for choosing a quality product from Frontier Equipment. We strive to give you the best equipment and the

More information

BELT CONVEYOR WC1335 ASSEMBLY & OPERATION MANUAL

BELT CONVEYOR WC1335 ASSEMBLY & OPERATION MANUAL BELT CONVEYOR ASSEMBLY & OPERATION MANUAL Read this manual before using product. Failure to follow instructions and safety precautions can result in serious injury, death, or property damage. Keep manual

More information

Quiet Collector. Model No & Up

Quiet Collector. Model No & Up FORM NO. -0 Quiet Collector Model No. 79-990000 & Up Operator s Manual IMPORTANT: Read this manual, and your tractor manual, carefully. They contain information about your safety and the safety of others.

More information

OPERATOR'S MANUAL & PARTS LIST

OPERATOR'S MANUAL & PARTS LIST GRAVITY GRAIN BOES OPERATOR'S MANUAL & PARTS LIST GRAVITY GRAIN BOES Model 50 (After Serial #14860 & D-Series) Model 85 (After Serial #C104749 & D-Series) Model 90 (After Serial #D0580100 & Up) Model 450

More information

36 Tiller Wheel Horse Lawn and Garden Tractor Attachment

36 Tiller Wheel Horse Lawn and Garden Tractor Attachment Form No. 9 6 Rev B 6 Tiller Wheel Horse Lawn and Garden Tractor Attachment Model No. 797 890000 and Up Operator s Manual English(En) Contents Page Introduction................................ Safety.....................................

More information

GRAIN AUGER SELF-PROPELLED AUGER KIT ASSEMBLY & OPERATION

GRAIN AUGER SELF-PROPELLED AUGER KIT ASSEMBLY & OPERATION GRAIN AUGER ASSEMBLY & OPERATION Read this manual before using product. Failure to follow instructions and safety precautions can result in serious injury, death, or property damage. Keep manual for future

More information

ASSEMBLY INSTRUCTIONS

ASSEMBLY INSTRUCTIONS CONTENTS ASSEMBLY INSTRUCTIONS... 1 TO THE DEALER... 1 SAFETY... 1 UNPACKING AND CHECKING PARTS... 2 Unpacking Wooden Crate...2 Checking Parts...3 TRACTOR PREPARATION... 4 ASSEMBLY... 4 Boom Assembly...4

More information

OPE R AT O R S MANU A L QUICK-HITCH ADAPTER. 5BP (Field conversion kit)

OPE R AT O R S MANU A L QUICK-HITCH ADAPTER. 5BP (Field conversion kit) OPE R AT O R S MANU A L 5BP006750 (Field conversion kit) Manual 5BP97378B Date 06/8/05 SAFETY Take note! This safety alert symbol found throughout this manual is used to call your attention to instructions

More information

HYDROSTATIC SUPER SWEEP

HYDROSTATIC SUPER SWEEP HYDROSTATIC SUPER SWEEP PORTABLE & TRUCK MOUNT SUPERSWEEP ASSEMBLY & OPERATION MANUAL Read this manual before using product. Failure to follow instructions and safety precautions can result in serious

More information

DIAMONDBACK/EDGE GRASS COLLECTION SYSTEM PARTS & OPERATORS MANUAL

DIAMONDBACK/EDGE GRASS COLLECTION SYSTEM PARTS & OPERATORS MANUAL DIAMONDBACK/EDGE GRASS COLLECTION SYSTEM PARTS & OPERATORS MANUAL GRASS CATCHER W/WEIGHT: TUBE KIT: BLOWER KIT: 48 5101305 632093 632078 52 5101305 542119 632074 60 632086 542120 632081 3 WORLDLAWN POWER

More information

BALE KING GT40 Grain Feeder Operator's & Parts Manual Last Update: November 20, 2014 Bridgeview Manufacturing Inc - 1 -

BALE KING GT40 Grain Feeder Operator's & Parts Manual Last Update: November 20, 2014 Bridgeview Manufacturing Inc - 1 - BALE KING GT40 Grain Feeder Operator's & Parts Manual Last Update: November 20, 2014 Bridgeview Manufacturing Inc - 1 - Your Authorized Dealer: Your Serial Number: The Serial Number is located on the tank.

More information

TFX2 80 TFX TFX2 Series Augers

TFX2 80 TFX TFX2 Series Augers TFX2 80 TFX2 100 TFX2 Series Augers Our Best Farm Proven Features Main Tubes Main tube connections are welded and flanges are bolted togther for maximum strength. Aircraft cable trussing on longer units

More information

Swing-Away Grain Auger

Swing-Away Grain Auger Swing-Away Grain Auger MKX 100 Operator s Manual This manual applies to: MKX 100-53, MKX 100-63, MKX 100-73, MKX 100-83 Original Instructions Read this manual before using product. Failure to follow instructions

More information

OPERATOR AND PARTS MANUAL

OPERATOR AND PARTS MANUAL OPERATOR AND PARTS MANUAL Backsaver Auger Model 370, 385, 395 0305 FK35 6990633 (-3) Printed in U.S.A. Bobcat Company 03 0603 Rev 8866496 Table of Contents - 3" Backsaver Auger TABLE OF CONTENTS Manufacturer

More information

610 BUSHEL MANURE SPREADER

610 BUSHEL MANURE SPREADER 610 BUSHEL MANURE SPREADER RODA MANUFACTURING 1008 LOCUST ST. HULL, IA. 51239 Art s-way Manufacturing 712-439-2366 Co., Inc. Hwy 9 West - PO Box 288 WWW.RODAMFG.COM Armstrong, IA. 50514 U.S.A 2 INTRODUCTION

More information

GRAIN BELT CONVEYOR 1300, 1500, 1800, 2000, 2400 SERIES ( ) OPERATION MANUAL

GRAIN BELT CONVEYOR 1300, 1500, 1800, 2000, 2400 SERIES ( ) OPERATION MANUAL GRAIN BELT CONVEYOR 1300, 1500, 1800, 2000, 2400 SERIES (30-120 ) OPERATION MANUAL This manual applies to the following models: 1335, 1340, 1345, 1355 1535, 1540, 1545, 1550, 1555, 1565, 1575, 1585, 1590,

More information

WOOD CHIPPER WC1105 5PQ (8/08/2012)

WOOD CHIPPER WC1105 5PQ (8/08/2012) O P E R A T O R ' S M A N U A L WOOD CHIPPER WC1105 5PQ990102 (8/08/2012) To the Owner; Thank-You for choosing a quality product from Frontier Equipment. We strive to give you the best equipment and the

More information

GRASS CATCHER PART S & OPERATORS MANUAL

GRASS CATCHER PART S & OPERATORS MANUAL GRASS CATCHER PART S & OPERATORS MANUAL WORLDLAWN POWER EQUIPMENT, INC. WORLDLAWN.COM 2415 ASHLAND AVE BEATRICE, NE 68310 800-267-4255 FAX 402-223-4103 2 3 4 OPERATORS MANUAL This catcher manual is for

More information

Max IV Rear Axle Replacement For models after Serial Number and all rear splined axle replacements.

Max IV Rear Axle Replacement For models after Serial Number and all rear splined axle replacements. Max IV Rear Axle Replacement For models after Serial Number 19089 and all rear splined axle replacements. 10/8/03 Max IV Snap Ring Rear Axle replacement.doc Tools required: 9/16 Wrench 6 Extension Steel

More information

SAC Liquid Manure Flow Meter

SAC Liquid Manure Flow Meter LM300000 REV A 11/11/2009 QUALITY PEOPLE, QUALITY PRODUCTS SAC Liquid Manure Flow Meter Operation and Service Manual ASSEMBLY CALIBRATION OPERATION REPLACEMENT PARTS READ complete manual CAREFULLY BEFORE

More information

CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL

CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL 2 Table of Contents Section 1: General Information Page Handle Assembly Instructions 4 Maintenance All Models 6 Oil Change Procedures All Models 9 Height Adjustment

More information

Z Master. 62 Mower. for Z Master Z 255 Traction Unit. Model No & UP. Operator s Manual

Z Master. 62 Mower. for Z Master Z 255 Traction Unit. Model No & UP. Operator s Manual FORM NO. 9 88 Z Master 6 Mower for Z Master Z 55 Traction Unit Model No. 7408 89000 & UP Operator s Manual IMPORTANT: Read this manual carefully. It contains information about your safety and the safety

More information

Self-Propelled Auger Kit

Self-Propelled Auger Kit Self-Propelled Auger Kit STX2 / XTA Series Assembly Manual Original Instructions LOOKING FOR PARTS? Check out our online Parts Catalog! Read this manual before using product. Failure to follow instructions

More information

ProLine. 36 Mower. for Mid-Size Traction Unit. Model No & Up. Operator s Manual

ProLine. 36 Mower. for Mid-Size Traction Unit. Model No & Up. Operator s Manual FORM NO. 8 77 Rev A ProLine 6 Mower for Mid-Size Traction Unit Model No. 05 79000 & Up Operator s Manual IMPORTANT: Read this manual carefully. It contains information about your safety and the safety

More information

TFX SERIES GRAIN AUGERS 831, 836, 841, 846, 851, 1031, 1036, & 1041 MODELS ASSEMBLY & OPERATION MANUAL

TFX SERIES GRAIN AUGERS 831, 836, 841, 846, 851, 1031, 1036, & 1041 MODELS ASSEMBLY & OPERATION MANUAL TFX SERIES GRAIN AUGERS 831, 836, 841, 846, 851, 1031, 1036, & 1041 MODELS ASSEMBLY & OPERATION MANUAL Read this manual before using product. Failure to follow instructions and safety precautions can result

More information

W & A 12 ROW TOP LEVELING STACKER LEVEL BANDER

W & A 12 ROW TOP LEVELING STACKER LEVEL BANDER W & A 12 ROW TOP LEVELING STACKER LEVEL BANDER NO. 3640 OPERATOR S MANUAL TO THE OWNER: Congratulations on your purchase of a new W & A Top Leveling Stacker Level Bander. Your selection is an indication

More information

JEEVES. JEEVES Installation Manual. Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market

JEEVES. JEEVES Installation Manual. Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market 1 888-323-8755 www.nwlifts.com JEEVES Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market This manual will cover the installation procedure step-by-step. The installation of this dumbwaiter

More information

KING COBRA/CALIBER GRASS COLLECTION SYSTEM PARTS & OPERATORS MANUAL

KING COBRA/CALIBER GRASS COLLECTION SYSTEM PARTS & OPERATORS MANUAL KING COBRA/CALIBER GRASS COLLECTION SYSTEM PARTS & OPERATORS MANUAL GRASS CATCHER W/WEIGHTS: TUBE KITS: BLOWER KITS: 52 542128 52 542119 5101002 60 542129 60 542120 5101003 2 WORLDLAWN POWER EQUIPMENT

More information

LOG SPLITTER. Heavy Duty PTO Driven. Owners Illustrated Instruction Book & Parts List

LOG SPLITTER. Heavy Duty PTO Driven. Owners Illustrated Instruction Book & Parts List LOG SPLITTER Heavy Duty PTO Driven Owners Illustrated Instruction Book & Parts List Grovebury Road, Leighton Buzzard, Bedfordshire. LU7 4UX. UK. Tel:01525 375157. Fax:01525 385222. Email: enquires@brownsagricultural.co.uk

More information

DWHOIST. Drywall Hoist Assembly & Operating Instructions

DWHOIST. Drywall Hoist Assembly & Operating Instructions DWHOIST Drywall Hoist Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. This manual provides important information

More information

Riding Mowers. Z44 and Z52 Accu-Z Razor (S/N and above) SM Service Manual Printed 9/24/09

Riding Mowers. Z44 and Z52 Accu-Z Razor (S/N and above) SM Service Manual Printed 9/24/09 Riding Mowers Z44 and Z52 Accu-Z Razor (S/N 472620 and above) 23802 357-044SM Service Manual 2006 Printed 9/24/09 Copyright 2006 All rights Reserved Land Pride provides this publication as is without warranty

More information

OPERATOR AND PARTS MANUAL

OPERATOR AND PARTS MANUAL OPERATOR AND PARTS MANUAL Backsaver Auger Models 684 &604 0806 FK370 Revision 3 6990633 (-3) Printed in U.S.A. Bobcat Company 03 0603 Rev 8866496 Table of Contents - Backsaver Auger 684 & 604 TABLE OF

More information

OPERATOR'S MANUAL 304 Row Mulcher

OPERATOR'S MANUAL 304 Row Mulcher OPERATOR'S MANUAL 0 Row Mulcher PUBLICATION DATE: // Millcreek Manufacturing Company Reservoir Road Honey Brook PA MILLCREEK PART# 0 WARNING: DO NOT assemble, operate, or maintain this equipment without

More information

HR-520 HOIST. Installation & Operation Manual. To Be Filled In By Installer. Pump Installation And Operation Manual#: In Service Date: Dealer:

HR-520 HOIST. Installation & Operation Manual. To Be Filled In By Installer. Pump Installation And Operation Manual#: In Service Date: Dealer: Website: www.tbei.com E-mail: sales@tbei.com Phone: 1-800-869-9162 Rugby 1-800-255-4345 DuraClass 1-800-533-0494 Crysteel HR-520 HOIST Installation & Operation Manual To Be Filled In By Installer Hoist

More information

Section K WC1335 AND WC15 SERIES CONVEYORS TUBE / UNDERCARRIAGE / DRIVE INDEX

Section K WC1335 AND WC15 SERIES CONVEYORS TUBE / UNDERCARRIAGE / DRIVE INDEX INDEX Section K WC33 AND WC SERIES CONVEYORS TUBE / UNDERCARRIAGE / DRIVE Description Page WC33 basic conveyor... K2-3 WC basic transfer... K4- WC70 basic tube... K-7 WC80 basic tube... K8-9 WC90 basic

More information

TABLE OF CONTENTS. Winch (No. 1550) Drawing Winch (No. 1550) Parts List Winch (No. K2550) Drawing Winch (No. K2550) Parts List...

TABLE OF CONTENTS. Winch (No. 1550) Drawing Winch (No. 1550) Parts List Winch (No. K2550) Drawing Winch (No. K2550) Parts List... TABLE OF CONTENTS DESCRIPTION PAGE NUMBER Warranty... 1 Safety Instructions... 2 Safety Signs... 4 Operating Instructions... 6 Maintenance and Lubrication... 8 Storage... 8 Assembly Instructions... 9 Tube

More information

Installation Notes: #86000-R Race Series +3.5 L/T Kit

Installation Notes: #86000-R Race Series +3.5 L/T Kit 159 North Maple St. Unit J, CORONA CA 92880 P. 951-737-9682 F. 951-737-9006 WWW.CHAOSFAB.COM Installation Notes: #86000-R Race Series +3.5 L/T Kit Factory manual is recommended for removal and re-installation

More information

PORTA-DOCK, INC. 65A 1155 DOUBLE PERSONAL WATERCRAFT LIFT

PORTA-DOCK, INC. 65A 1155 DOUBLE PERSONAL WATERCRAFT LIFT Page 1 of 9 PORTA-DOCK, INC. 65A 1155 DOUBLE PERSONAL WATERCRAFT LIFT Thank you for purchasing our product! Please read these instructions and follow them step by step.* STEP 1. Separate and group like

More information

'99-03 CHEVROLET/GMC IFS 4WD 6" SUSPENSION SYSTEM P/N INSTALLATION INSTRUCTIONS

'99-03 CHEVROLET/GMC IFS 4WD 6 SUSPENSION SYSTEM P/N INSTALLATION INSTRUCTIONS 1/16/04 '99-03 CHEVROLET/GMC IFS 4WD 6" SUSPENSION SYSTEM P/N. 10-41099 INSTALLATION INSTRUCTIONS NOTE: Each Lift Kit and options to Lift Kits are packaged separately. Therefore, installation procedures

More information

OWNER S, INSTALLATION AND PARTS MANUAL

OWNER S, INSTALLATION AND PARTS MANUAL OWNER S, INSTALLATION AND PARTS MANUAL QUICK HITCH CONVERSION KIT CONVERTS 24/MT TO 26 SERIES HITCH FOR PLOW SERIAL NUMBERS AFTER 24G100000 24D100000 MTD200000 MTG200000 2005 Sno-Way International 97101198A

More information

MT2000 HYDRAULIC SWATH ROLLER COMMON HYDRAULIC ASSEMBLY INSTRUCTIONS Kit Part No

MT2000 HYDRAULIC SWATH ROLLER COMMON HYDRAULIC ASSEMBLY INSTRUCTIONS Kit Part No Free Form PLASTICS MT2000 HYDRAULIC SWATH ROLLER COMMON HYDRAULIC ASSEMBLY INSTRUCTIONS Kit Part No. 7101-02 ASSEMBLY INSTRUCTIONS & OPERATION EFFECTIVE S/N: 39632SR01 - DATE It is recommended to carefully

More information

Reproduction. Not for. Hybrid Frame Dual Stage Snowthrowers. Parts Manual

Reproduction. Not for. Hybrid Frame Dual Stage Snowthrowers. Parts Manual Parts Manual Attachment Mfg. No. Description 1695984 (I924E), 9TP 24" Dual Stage Snowthrower 1695993 (H924RX), 9TP 24" Dual Stage Snowthrower (CE/Export) Hybrid Frame Dual Stage Snowthrowers Not for Reproduction

More information

OperatOr and parts Manual 14" 122' Swing Drive Auger

OperatOr and parts Manual 14 122' Swing Drive Auger SZ106646 OperatOr and parts Manual 14" 122' Swing Drive Auger 06/2010 Introduction 14" 122' Swing Drive Auger TO THE OWNER Thank you for purchasing a Farm King 14" 122' Swing Drive Auger. Farm King Swing

More information

Hi Cap 54 Grain Cleaner

Hi Cap 54 Grain Cleaner OWNER S MANUAL Hi Cap 54 Grain Cleaner PNEG-1147 Date: 3-1-02 PNEG-1147 SAFETY INFORMATION PLEASE READ WATCH FOR THIS SYMBOL! IT POINTS OUT IMPORTANT SAFETY PRECAUTIONS. IT MEANS, ATTENTION - BECOME ALERT!

More information

42in GT Classic Single Stage Snowthrower Conversion Kit XT Series Garden Tractor

42in GT Classic Single Stage Snowthrower Conversion Kit XT Series Garden Tractor Form No. 9 66 in GT Classic Single Stage Snowthrower Conversion Kit XT Series Garden Tractor Part No. 06 88 Installation Instructions English (EN) This kit is for installing an existing 00 Series Classic

More information

Collector Drive for 60 Mower

Collector Drive for 60 Mower FORM NO. -66 Collector Drive for 60 Mower Model No. 7965-990000 & Up Operator s Manual IMPORTANT: Read this manual, and your tractor manual, carefully. They contain information about your safety and the

More information

ProPass-200 Top Dresser

ProPass-200 Top Dresser Setup Manual Form No. 3365-184 Rev A ProPass-200 Top Dresser Model No. 44700-Serial No. 310000001 and Up Model No. 44701-Serial No. 310000001 and Up Model No. 44704 Model No. 44705 Model No. 44706 Model

More information

CONVEYOR S-DRIVE P / 2000 P SERIES OPERATION MANUAL

CONVEYOR S-DRIVE P / 2000 P SERIES OPERATION MANUAL CONVEYOR S-DRIVE 55-100 1500 P / 2000 P SERIES OPERATION MANUAL Read this manual before using product. Failure to follow instructions and safety precautions can result in serious injury, death, or property

More information

OPERATOR AND PARTS MANUAL

OPERATOR AND PARTS MANUAL OPERATOR AND PARTS MANUAL Backsaver Auger Model and 04 SZ063 6990633 (-3) Printed in U.S.A. Bobcat Company 03 0603 Rev 8866496 Table of Contents - Backsaver Auger / TABLE OF CONTENTS Manufacturer s Statement:

More information

HR-540/HR-550 HOIST Installation & Operation Manual

HR-540/HR-550 HOIST Installation & Operation Manual Website: www.tbei.com E-mail: sales@tbei.com Phone: 1-800-869-9162 Rugby 1-800-255-4345 DuraClass 1-800-533-0494 Crysteel HR-540/HR-550 HOIST Installation & Operation Manual To Be Filled In By Installer

More information

ASSEMBLY INSTRUCTION MANUAL

ASSEMBLY INSTRUCTION MANUAL ASSEMBLY INSTRUCTION MANUAL 10" & 13" Backsaver Augers Electric Mover Kit 022014 SZ001099 Table of Contents - 10" and 13" Backsaver Augers - Electric Mover Kit Table of Contents Introduction...4 Safety...5

More information

tRIPr Chief Grain Cart. Operator s Manual. Operator s Manual

tRIPr Chief Grain Cart. Operator s Manual. Operator s Manual 125-000-01 125-000-01 1tRIPr 1tRIPr Operator s Manual 1210 Chief Grain Cart Operator s Manual Operator s Manual TO THE DEALER Predelivery/Delivery Checklist 1210 Grain Cart PREDELIVERY/DELIVERY CHECKLIST

More information

STOP. Broadcast Spreader. Operator's Manual. Model No Safety Assembly Operation Maintenance Parts

STOP. Broadcast Spreader. Operator's Manual. Model No Safety Assembly Operation Maintenance Parts Operator's Manual STOP Broadcast Spreader Model No. 486.2400 DO NOT RETURN TO STORE For Missing Parts or Assembly Questions Call 1-866-56-8388 CAUTION: Before using this product, read this manual and follow

More information

Wheel Horse. 48 Snow Blade. Model No & Up. Operator s Manual

Wheel Horse. 48 Snow Blade. Model No & Up. Operator s Manual FORM NO. 8 8 Wheel Horse 8 Snow Blade for Classic Graden Tractors Model No. 7950 890000 & Up Operator s Manual IMPORTANT: Read this manual carefully. It contains information about your safety and the safety

More information

EMB MANUFACTURING INC.

EMB MANUFACTURING INC. GROUND DRIVE SPREADER MODELS MX50G, MX80G ASSEMBLY INSTRUCTION MANUAL Please review and understand the operators manual before attempting to operate this machinery. EMB MANUFACTURING INC. 4144 BOOMER LINE

More information

Operating and Assembly Manual

Operating and Assembly Manual Model 1080 Operating and Assembly Manual Midwest Equipment Manufacturing, Inc. 5225 Serum Plant Road Thorntown, IN 46071 08-02-16 SAFETY RULES Remember, any power equipment can cause injury if operated

More information

Twin Screw Undercar Conveyor

Twin Screw Undercar Conveyor Twin Screw Undercar Conveyor Owner s Manual #19015700 05-00 Table of Contents Operator Qualifications...................................... 1 Safety.................................................. 2-4

More information

201B Series Belted Portable Drum Rollers Operator s Manual for Morse Belted Portable Drum Rollers

201B Series Belted Portable Drum Rollers Operator s Manual for Morse Belted Portable Drum Rollers Contents Page Receiving Procedures.................... 1 Warranty............................. 1 Safety Information..................... 1-2 Machine Description................... 3 Options.............................

More information

Drive Over- Pit. Belt Accelerator & Multi-Purpose Belt Loader OWNER'S MANUAL (08/08)

Drive Over- Pit. Belt Accelerator & Multi-Purpose Belt Loader OWNER'S MANUAL (08/08) Drive Over- Pit Belt Accelerator & Multi-Purpose Belt Loader OWNER'S MANUAL 00028100 (08/08) Belt Accelerator & Multi-Purpose Belt Loader Table of Contents Warranty Information................. Inside

More information

Model 858-RH. Operating and Assembly Manual. Palmor Products Inc Serum Plant Road Thorntown, IN 46071

Model 858-RH. Operating and Assembly Manual. Palmor Products Inc Serum Plant Road Thorntown, IN 46071 Model 5-RH Operating and Assembly Manual Palmor Products Inc. 55 Serum Plant Road Thorntown, IN 6071 3/31/015 SAFETY RULES Remember, any power equipment can cause injury if operated improperly or if the

More information

INSTALLATION / OPERATING INSTRUCTIONS Reese Elite Series FIFTH WHEEL SLIDER HITCH

INSTALLATION / OPERATING INSTRUCTIONS Reese Elite Series FIFTH WHEEL SLIDER HITCH INSTALLATION / OPERATING INSTRUCTIONS Reese Elite Series FIFTH WHEEL SLIDER HITCH DEALER/INSTALLER: (1) Provide this Manual to end user. (2) Physically demonstrate hitching and unhitching procedures in

More information

Assembly & Installation Instructions

Assembly & Installation Instructions TM P R O D U C T S Assembly & Installation Instructions FOR 28 SERIES SNOWPLOW PIVOT ASSEMBLY AND FLOAT LIMITER 99103000 FOR SERIAL NUMBERS 28D100000 TO 28D100770 97100552A 1. THINK SAFETY, ALWAYS WEAR

More information

CPHD POST HOLE DIGGER Operator s/parts Manual. Table of Contents

CPHD POST HOLE DIGGER Operator s/parts Manual. Table of Contents CPHD POST HOLE DIGGER Operator s/parts Manual Table of Contents Warranty Information... -3 Dealer Checklist... 4 Safety Precautions... 5-6 Federal Laws and Regulations... 7 Torque Specifications... 8 Important

More information