Catalogue. HotShieldPTC TM. High Operating Temperature Smoke Management and Fire Dampers.

Transcription

1 Catalogue HotShieldPTC TM High Operating Temperature Smoke Management and Fire Dampers

2 Product Features Smoke Management & Fire Dampers operational up to 00 C for a period of two hours Thermally Insulated Electric Control Modes Pneumatic option available 50 C for one hour Halogen Free Low Smoke & Fume cabling supplied as a standard feature Low closed blade leakage HotShield Dampers when closed have up to 4 hours fi re resistance when tested to BS476 Parts 0 and Actionpac Damper Control System compatibility HotShield Vent PTC reverse action dampers for High Operating Temperature Smoke Control & Extract Applications HotBox Thermal Enclosure - superior performance to older thermal enclosures this uses our specially developed lightweight, high performance material. Introduction Actionair have developed a new technically advanced thermal enclosure that actually has the ability to absorb heat energy when subjected to a high temperature environment. The performance criteria involves continuous operation of the complete damper and actuator assembly at elevated temperatures. This new enclosure is made from a phenolic composite resin with excellent endothermic properties. A chemical reaction occurs within the insulating material when it is heated. This reaction has the effect of lowering the temperature inside the enclosure, thus prolonging the duration of the actuator s operation at elevated temperatures. Smoke and other products of combustion kill at least 80% of recorded fi re victims, smoke is debilitating and can render people unconscious minimising their chances of survival. Many more die weeks or months later from the lingering effects and toxic effects of smoke inhalation. Smoke and toxic gases the Silent Killers have to be managed and controlled quickly and effectively to avoid confusion and panic from the threat posed to life safety and the extraction and control of these deadly gases is of paramount importance for the safe evacuation of the buildings occupants. The importance of the subsequent smoke damage that can occur to adjacent property and fittings is also recognised, as this can have disastrous effects on homes and businesses as recognised in the Loss Prevention Council Design Guide for Fire Protection in Buildings. Actionair have developed the HotShield PTC High Temperature Smoke Management and Fire Dampers along with the HotShield Vent PTC Smoke Control and Extract Dampers to enable the concepts of fi re engineering to be employed in ducted smoke ventilation systems. These dampers designed, tested and approved to deliver high temperature operation at up to 00 C for two hours, provide the designer with the capability of extracting hot smoke and combustion gases through a common smoke extraction duct linked to adjacent fi re zones and floors. As smoke can spread rapidly and efficiently through a building ductwork system, damper operation needs to be initiated by a smoke detection system, as thermal sensing can often be too late. HotShield PTC and HotShield Vent PTC dampers are designed to be interfaced with a smoke detection/fi re alarm system.

3 Application HotShield PTC High Operating Temperature Smoke Management and Fire Dampers Designed for installation in high temperature ductwork systems with mechanical smoke extraction. As these ductwork systems regularly serve more than one fire zone or floor when smoke extraction is conducted from one area, it is essential to fully fire protect adjoining fire zones from ductwork penetrations that are connected to the smoke extract duct. For this purpose HotShield PTC dampers, when closed are a fire resisting damper to BS 476 part 0 for up to four hours, thus providing the fire isolation required. Closure of the damper is achieved by removal/loss of the electrical supply. When used for smoke extraction, under authorised control, the HotShield PTC damper will remain open under electrical power for a period of two hours at temperatures of up to 00 C thus allowing the safe extraction of smoke and hot gases of combustion through the extended fire compartment created by the fire resisting ductwork. HotShield PTC Smoke Management Fire Dampers may also be used for controlled supply of make up air as a function of the fire engineering process. HotShield Vent PTC High Operating Temperature Smoke Control and Extract Dampers Provide flexible smoke management where other fire compartments are not interconnected to a common fire resisting ductwork system. Designed to spring to the open position by stored energy and remain closed when powered. HotShield Vent PTC dampers allow controlled smoke extraction to take place with a dedicated smoke control system if required, but retaining low leak closure of the smoke extract duct penetrations into the protected space during normal conditions. Casing Features With double skin spigotted galvanised steel (to BS EN 1014) casing the HotShield PTC dampers comply to Class A and B of Eurovent Document / and Test Procedures for Classes A, B and C of HVCA Ductwork Specification DW144. Damper casings are manufactured with welded spigotted connections suitable for Square, Rectangular, Circular and Flat Oval duct connections. As an extra cost option, casings can be manufactured in 40 grade (Type ) Ferritic or 16 grade (Type ) Austenitic stainless steel, 1.mm thick. Blade Features The Damper blades are aerodynamic,double skin 40 grade (Type ) to BS EN Ferritic stainless steel which are 75mm deep and interlock to form a positive smoke and fire resisting shield. Incorporated within the blade profile is a high temperature silicone seal to ensure low closed blade leakage at temperatures up to 00 C for two hours. Stainless steel blade end bearings and peripheral gasketting maintain the low closed blade leakage allowing for expansion under full fire conditions. Optional Blade construction 16 grade (Type ) Austenitic Stainless Steel. Parameters HotShield PTC and HotShield Vent PTC Dampers to maximum width and height dimensions can be used where the operating total system pressure is up to 1500 Pascals and duct velocities to 15m/second. As with any life safety damper product, a suitable planned inspection programme should be implemented. For specialist and/or aggressive applications, please refer to Actionair Sales Office. Proportional Torque Control A new generation High Operating Temperature Smoke Management and Fire Damper, thermally Insulated Control Mode assembly, with a unique and dedicated Proportional Torque Control for optimised Damper/ Control Mode torque performance. The unique snaplock drive interface ensures user friendly, easy and secure connection of the Control Mode to the damper. The drive interface, which is totally independent of the ductwork, and provides ease of connection to square, rectangular, circular and flat oval ductwork, including fire resisting ductwork.

4 Control Options A choice of a 4V or 0V Control Modes located outside the ductwork and (protected by its own thermally insulated enclosure) and Halogen Free Low Smoke and Fume cables, allows HotShield PTC Damper control up to 00 C for a period of two hours. The Control Mode upon receipt of the relevant supply voltage will motor the Damper to the open position. Closure of the Damper is achieved by removal/ loss of the electrical supply. The Damper when closed will provide up to four hours fire resistance in accordance with BS 476 Part 0. Control Modes have two separate volt free contacts for the provision of external damper status indication. (No thermal links available). HotShield Vent PTC Dampers and associated Control Modes are reverse action with spring opening. HotShield and Hot/VentShield HM5 PTC 10W (1.5VA) 4V end switches SPDT 50V 6()A HotShield Off Fail-safe Close HM6 PTC 1W (14VA) 0V end switches SPDT 50V 6()A HotShield Off Fail-safe Close HMV5 PTC Vent 10W (1.5VA) 4V end switches SPDT 50V 6()A Hot/VentShield Off Fail-safe Open HMV6 PTC Vent 1W (14VA) 0V end switches SPDT 50V 6()A Hot/VentShield Off Fail-safe Open HotShield and Hot/VentShield Control Modes HM5 PTC and HM6 PTC (operational for 00 C) are NOT supplied with the Electrical Thermal Release (ETR). They Fail-safe when the power is off/interrupted). HotShield and Hot/VentShield (Modulating) HM5-P PTC 4V 7W (10VA) end switches SPDT 50V 6()A HotShield Off Fail-safe Close -10V Set position HMV5-P PTC Vent 4V 7W (10VA) end switches SPDT 50V 6()A Hot/VentShield Off Fail-safe Open -10V Set position HotShield and Hot/VentShield Control Modes HM5 P PTC (operational for 00 C) are NOT supplied with Electrical Thermal Release (ETR) and Fail-safe when the power is off/interrupted. HotShield and Hot/VentShield Position Drive Open / Drive Closed 4 HM5-P PTC HM6-P PTC HM5-P and HM6-P are NOT supplied with ETR and remain in the desired emergency position when power is interrupted. 4V 7W (10VA), end switches SPDT 50V 6()A 0V 8W (1.5VA), end switches SPDT 50V 6()A HM9 PTC Pneumatic Air Off Fail-safe Close HMV9 PTC Vent Pneumatic Air Off Fail-safe Open Pneumatic version rated at 50 C for 1 hour.

5 Application and Wiring Mode HM5 (4V System) On Damper motors open. Off Spring closure. Cable specification: Si HF Low Smoke and Fume, Halogen Free, to IEC Conforming to 7//EEC directive. Release Time secs. Reset Time 60 secs. (Connect 4V via a safety isolating transformer.) AC/DC 4V 50 / 60 Hz 1.5 VA 10/ W Imax 5ms C CONTINUOUS AC 50V 6()A M SUPPLY 4V AC or DC VOLT FREE CONTACT CLOSED WHEN DAMPER RELEASED VOLT FREE CONTACT CLOSED WHEN DAMPER RESET IP54 Rated Mode HM6 (0V System) On Damper motors open. Off Spring closure. Cable specification: Si HF Low Smoke and Fume, Halogen Free, to IEC Conforming to 7//EEC directive. Release Time secs. Reset Time 60 secs. (To isolate from main power supply, the system must incorporate a device which disconnects the phase conductors, with a least mm contact gap.) AC 0V 50 / 60 Hz 14 VA 1/4 W C CONTINUOUS AC 50V 6()A M BLUE BROWN N L1 1 4 SUPPLY 0V AC 50/60 Hz VOLT FREE CONTACT CLOSED WHEN DAMPER RELEASED VOLT FREE CONTACT CLOSED WHEN DAMPER RESET IP54 Rated 5

6 Application and Wiring Mode HM5-P (4V System) open Damper motor opens close Damper motor closes x end switches SPDT <60s for 90 o Cable specification: AC/DC4V 50/60 Hz 18VA 1/0.5W T (1) () () (4) T AC/DC 4 V No. 4 Not Required. Snip off/terminate. Si HF Low Smoke and Fume, Halogen Free, to IEC Conforming to 7//EEC directive. (To isolate from main power supply, the system must incorporate a device which disconnects the phase conductors, with a least mm contact gap.) Close Open IP54 Rated Mode HM6-P (0V System) open Damper motor opens close Damper motor closes x end switches SPDT <60s for 90 o Cable specification: Si HF Low Smoke and Fume, Halogen Free, to IEC Conforming to 7//EEC directive. (Connect 4V via a safety isolating transformer.) IP54 Rated Mode HM5-P (4V System) 6 On Damper motors open. Off Spring closure. DC-10V Signal - Variable Position Cable specification: Si HF Low Smoke and Fume, Halogen Free, to IEC Conforming to 7//EEC directive. Release Time 16 secs. Reset Time 10 secs. AC/DC4V 50/60 Hz 10VA 7/W T BLACK (1) RED () WHITE () ORANGE (5) T AC/DC 4 V (Connect 4V via a safety isolating transformer.) IP54 Rated

7 Thermal Enclosure Damper/Control Mode Interface Actionair has developed a new thermal enclosure to surround the actuator. Our new enclosure is manufactured from a technically advanced material, designed specifically for Actionair, this makes the new enclosure is far more robust and offers improved performance over previous enclosures. The enclosure is made specially designed lightweight material with excellent endothermic properties, which means the thermal enclosure has the ability to absorb heat energy when subjected to extremely high HotShield PTC Damper with unique snaplock Damper/ Control Mode Interface The Actionair unique snaplock drive interface ensures user friendly, easy and secure connection of the Control Mode to the damper. The drive interface which is totally independent of the ductwork, eliminates the need for costly dedicated duct sections, and provides ease of connection to square, rectangular, circular and flat oval ductwork. The drive interface can be used up to wall thicknesses of 50mm. The interface allows the Control Modes Enclosure Position One temperatures. Vertical Orientation Drawing No: Sheet Rev (cables exit Third down) Angle A All dimensions in mm. Do NOT scale from drawing. If in doubt ASK! Enclosure Positioning Projection be fitted in any one of three orientations i.e. Vertically down, Position 1 Horizontally, Position, (standard) or Vertically up, Position. This can be simply and easily carried out on site, by the using Actionair multi positions kit. This flexibility ensures that the damper and control mode require the minimal amount of room. This drive interface also guarantees that only the correct and certified Actionair products can be used. Creat D 5 Clearance C (Enclosure) 06 (Enclosure) Ctrs Enclosure Position 1 Details i.e. Vertical orientation with cable exit down 116 Ctr 17.5 Ctr B 400 (Enclosure) 48 A (Enclosure) 410mm Minimum distance required for the installation & removal of the Thermal Enclosure & Interface Assembly 6 5 4

8 6 Drawing No: Sheet Rev 5 Third Angle Projection A 4 All dimensions in mm. Do NOT scale from drawing. If in doubt ASK! Enclosure Position Two D Horizontal Orientation (cables exit sideways) 5 Clearance C (Enclosure) (Enclosure) Enclosure Position Details i.e. Horizontal orientation with cable exit sideways 4.5 Ctrs 17.5 Ctr B 06 (Enclosure) A R D C A P Drawing No: 6 Sheet8 78Rev8 116 Ctr 58mm Min 5 distance required for installation & 4 removal of Third Enclosure Angle & Interface Assy A All dimensions in mm. Do NOT scale from drawing. If in doubt ASK! Projection C P Cr D P In E D 6 Enclosure Position Three Vertical Orientation (cables exit up) 5 4 The information disclosed herein was originated by and is the property of Swegon Air Management Limited (SAML). SAML reserves all patent, proprietary,design, use, sale, manufacturing and reproduction rights thereto. Th D 5 Clearance C (Enclosure) 06 (Enclosure) Enclosure Position Details i.e. Vertical orientation with cable exit up B 4.5 Ctrs (Enclosure) (Enclosure) A mm Min distance required for installation & removal of Enclosure & Interface Assy The information disclosed herein was originated by and is the property of Swegon Air Management Limited (SAML). SAML reserves all patent, proprietary,design, use, sale, manufacturing and reproduction rights there

9 HotShield Damper Interface Enclosure (HDIE) Actionair have developed a unique thermal enclosure to protect the Actionpac LNS range of damper interfaces currently available. The enclosure consists of two separate materials, enabling the HDIE to function at the extreme temperature specified. The outer casing has endothermic properties that significantly slows down the internal temperature rise in a high temperature emergency condition and the inner casing is a special thermal insulating material. The maximum temperature is 00 C for up to two hours, this has been tested and independently witnessed by BRE (Ref Test No. 1067A). The HDIE enclosure is to be used in HotShield PTC applications where the Actionpac LNS system is being used to control the dampers. Unit s and SDIs can be installed within the HDIE enclosure. The HDIE can be mounted in any orientation, on a flat surface or alternative suitable mounting system. Sectional View of HDIE Enclosure HDIE Lid The, or SDI units are supplied without the damper interface electronics, which will be supplied separately at commissioning stage. Maximum normal external operating temperature: 0 C Total Weight (including internal DIs) = 11.5kg (approx) Typical Installation 1. Fix the -off mounting brackets provided to the underside of the HDIE enclosure by screwing into the threaded inserts with the M5 screws provided. Allowing suitable cable access around the HDIE enclosure, position it in the desired location and mark fi xings positions using the bracket holes as a template. Remove the HDIE enclosure lid by unscrewing the 6-off long screws/large flat washers 4. Securely mount the HDIE base in its intended position. Hole specification and fi xings by others 5. Remove DI/CMS lid 6. Connect cables and refit lid in union with Actionpac catalogue information 7. Refit enclosure lid with the 6-off screws/ large flat washers taking care to position cables in grooves. The inside insulation is sufficiently soft to compress locally around cables when the lid is screwed down. Note: HDIE lid may need to be removed and refitted again during testing/commissioning HDIE Dimensions H HDIE Base 9

10 Damper Installation & Control Mode Fitting The Actionair unique snaplock drive interface ensures user friendly, easy and secure connection of the control mode to the damper. The drive interface allows the control modes to be fitted in any one of three orientations i.e. y Vertically down - Position 1 y Horizontally - Position (standard) y Vertically up - Position Typical Installation 1. Install the HotShield PTC damper following the relevant install method detailed in the IO&M. Connect and fit ductwork to damper spigots. Remove the transit plate and discard/ recycle 4. Slide the snaplock drive interface into the damper drive shroud. Pull the key ring on the easy pull lever, this snaplocks the drive interface into position Care must be taken when back filling to ensure that the snaplock retaining pin location hole and the entry slot of the damper drive shroud is clear of builders work debris. Changing the Control Mode of the HotShield PTC to position 1 and on site: 1. Remove the 4-off M6 bolts and washers and lift off the thermal enclosure assembly. Rotate the interface input shaft fully anti-clock wise. Line up the output shaft slot on the underside of the interface with the slot on the interface plate 4. Locate the thermal enclosure assembly to desired position and fix it to the mounting flanges with M6 bolts and washers 5. Fully close the damper 6. Pull the key ring on the easy pull lever, insert the interface assembly into the damper shroud, line up its dotted line with the end of the shroud, release the lever to lock 7. Refer to standard O&M for testing 8. The information contained herein is subject to change without notice due to continuing research and development Reverse Mounting The thermal enclosure and control mode can be reverse mounted (as shown below) available on request. 10

11 Multiple Assemblies LHD STD RHD LHD Square and rectangular casings are available in multiple module arrangements, supplied complete with blanking strips for site assembly by others. Additional support as well as provision for thermal expansion (4mm/metre) should be allowed for multiple assemblies. STD RHD STD RHD PLAN VIEW LHD LHD STD RHD STD RHD PLAN VIEW Multiple assemblies require installation approval by the relevant local authority. STD RHD LHD STD RHD Installation Systems Types of installation frames available: DWFX TM (Dry Wall Fix) Installation System Typically for installation into Dry Wall and Stud Partitions HEVAC/HVCA Galvanised Steel Installation Frames Typically for installation into Blockwork and Concrete walls and floors DWFX-F (Dry Wall Fix - Frame) DWFX-C (Dry Wall Fix - Cleat) The Actionair DWFX-F installation method is BRE assessed to BS476 Pt 0/ for two hours. The Actionair DWFX-F consists of a 1.mm galvanised steel peripheral flange with 50 x 50mm angle cleats with 14 x 4mm oval slots, welded to damper casing for drop rod support. The Actionair DWFX-C consists of 50 x 50mm angle cleats with 14 x 4mm oval slots. Fully welded to damper casing for drop rod support prior to wall construction. 11 DWFX-C Dimensional Data mm x 4mm SLOT IN CLEATS

12 HEVAC/HVCA Galvanised Steel Installation Frames Galvanised Steel Installation Frames (as technical specification by HEVAC 6/5/8 Rev. March 01.) Installation frames are delivered to site as a complete assembly with the appropriate damper fitted therein. The frame shall be installed centrally in the thickness of a brick, blockwork or concrete surrounding wall or floor, or in the case of thick walls or floors, so that the centre line of the frame is at least 50mm away from the nearest face of the wall or floor in which the assembly is mounted. The building ties forming each fixing point shall provide a positive fixing into the structure. Multiple assembly dampers up to 1500 x 1500 or 000 x 1000 can be fitted into fully assembled installation frames and delivered as one piece. Dampers in excess of these sizes will be supplied in sections with the installation frame supplied in kit form (Drg AA/F/ This drawing and method statement will be supplied for assembly on site). The maximum size of kit form installation frames is 500 wide x 000mm high. 1. In brick or blockwork walls the tabs shall be bent out and solidly built into the mortar joints between the brick or blockwork. In the case of reinforced concrete walls and floors, the tabs shall be bent out and tied with wire to the reinforcing bars which will be deliberately left protruding into the opening The gap between the installation frame and builders work shall be backfilled with mortar or concrete on both sides of the flange. Adjacent frame assemblies must be separated by builders work of a minimum distance of 00mm (between installation frame upstand flanges) unless approval has been previously obtained from the appropriate authority. In no case shall the HEVAC/HVCA frame and damper assembly be held in position merely by the adjacent ductwork. It should be noted that in reinforced concrete structures (especially floors), it will not be sufficient to only backfill between the damper installation frame and the surrounding opening with mortar or fine aggregate concrete mix without provision for tying in the frame to the surrounding reinforced concrete structure. 1 Approximate Weights Square or Circular Duct Size (mm) Series 501 Square Series 501 Square + I/F Series 601 Circular Series 601 Circular + I/F Weights in KG. Weights provided exclude Control Mode/Thermal Enclosure. For total weight please add 10.4 kg for the Modes 5/6 actuator. (If ordered with optional 5m cables add 0.6kg)

13 Dimensional Data For Rectangular dampers spigots that are 5mm under duct size. *Widths and heights available in 1mm increments. Rectangular Dampers - Series 501 & 501 Basic Dampers Dampers with Installations Systems DWFX-F HEVAC/HVCA IF OVERALL FLANGE WIDTH IS 98mm OVERALL FLANGE HEIGHT IS 95mm FOR DUCT WIDTHS AND HEIGHTS OF MM OVERALL WIDTH OF INSTALLTION FRAME IS 14mm OVERALL HEIGHT OF INSTALLATION FRAME IS 40mm THIS DRAWING HAS B THIS DRAWING HAS BEEN PREPARED ON ON INFORMATION GI INFORMATION GIVEN TO RUSKIN AIR MANAGEMENT LTD. MANAGEMENT LTD. THIS THIS DRAWING DRAWING HAS HAS BEEN BEEN PREPARED PREPARED ON ON INFORMATION INFORMATION GIVEN GIVEN TO TO RUSKIN RUSKIN AIR AIR MANAGEMENT MANAGEMENT LTD. LTD. THIS DRAWING HAS BEEN PREPARED ON INFORMATION GIVEN TO RUSKIN AIR MANAGEMENT LTD. OVERALL WIDTH OF INSTALLATION FRAME IS 64mm OVERALL HEIGHT OF INSTALLATION FRAME IS 90mm THIS THIS DRAWING HAS HAS BEEN BEEN PREPARED ON ON INFORMATION GIVEN GIVEN TO TO RUSKIN AIR AIR MANAGEMENT LTD. LTD. THIS DRAWING HAS BEEN PREPARED ON INFORMATION GIVEN TO RUSKIN AIR FOR DUCT WIDTHS AND HEIGHTS OF MM OVERALL FLANGE WIDTH IS 448mm OVERALL FLANGE HEIGHT IS 445mm MANAGEMENT LTD. FOR DUCT WIDTHS 00MM MM WITH HEIGHTS OF MM FOR OVERALL HEIGHTS SEE mm FOR OVERALL HEIGHTS SEE mm OR mm AS ABOVE OR mm AS ABOVE THIS DRAWING HAS BEEN PREPARED THIS DRAWING HAS BEEN PREPARED THIS DRAWING ON INFORMATION HAS BEEN PREPARED GIVEN TO RUSKIN AIR ON INFORMATION GIVEN TO RUSKIN AIR MANAGEMENT LTD. MANAGEMENT LTD. ON INFORMATION GIVEN TO RUSKIN AIR MANAGEMENT LTD. FOR DUCT WITH WIDTHS AND HEIGHTS OF MM OVERALL FLANGE WIDTH DUCT WIDTH + 198mm OVERALL FLANGE HEIGHT DUCT HEIGHT + 195mm OVERALL WIDTH OF INSTALLATION FRAME DUCT WIDTH + 114mm - OVERALL HEIGHT OF INSTALLATION FRAME DUCT HEIGHT + 140mm

14 Dimensional Data For Circular and Flat Oval damper spigots are mm under duct size. Circular Dampers - Series 601 & 601 Basic Dampers Circular Dampers Series 601 FOR DAMPERS MM OVERALL FLANGE WIDTH = 98mm OVERALL WIDTH OF INSTALLTION FRAME IS 14mm OVERALL FLANGE HEIGHT = 95mm OVERALL HEIGHT OF INSTALLATION FRAME IS 40mm FOR CIRCULAR DAMPERS SERIES 601, DIAMETERS MM OVERALL FLANGE WIDTH = 448mm OVERALL WIDTH OF INSTALLATION FRAME IS 64mm OVERALL FLANGE HEIGHT = 445mm OVERALL HEIGHT OF INSTALLATION FRAME IS 90mm OVERALL WIDTH OF INSTALLATION FRAME = DUCT DIA + 166MM OVERALL HEIGHT OF INSTALLATION FRAME = DUCT FOR CIRCULAR DAMPERS SERIES 601, DIAMETERS MM OVERALL FLANGE WIDTH = DUCT DIA + 48mm DIA + 190MM OVERALL FLANGE HEIGHT = DUCT DIA + 45mm FOR DUCT DIAMETERS BETWEEN 970mm mm FOR DUCT DIAMETERS BETWEEN 970mm mm OVERALL WIDTH OF FLANGE WIDTH IS 1198mm OVERALL WIDTH OF FLANGE WIDTH IS 1198mm OVERALL HEIGHT OF INSTALLATION FRAME IS 1195mm OVERALL HEIGHT OF INSTALLATION FRAME IS 1195mm Flat Oval Dampers - Series 701 & 701 Basic Dampers Dampers with Installations Systems DWFX-F HEVAC/HVCA IF Flat Oval Dampers Series 701 OVERALL FLANGE WIDTH = DUCT DIA + 48mm OVERALL WIDTH OF INSTALLATION FRAME = DUCT DIA OVERALL FLANGE HEIGHT = DUCT DIA + 45mm + 166MM OVERALL HEIGHT OF INSTALLATION FRAME = DUCT DIA + 190MM Dampers with Installations Systems DWFX-F HEVAC/HVCA IF FOR DUCT WIDTHS BETWEEN 970mm mm FOR DUCT WIDTHS BETWEEN 970mm mm OVERALL WIDTH OF INSTALLATION FRAME IS OVERALL WIDTH OF INSTALLATION FRAME IS 1198mm 1198mm

15 Acoustic Data The data presented is from the Laboratory Determination of Acoustic and Aerodynamic Performance of HotShield PTC High Operating Temperature Smoke Management and Fire Dampers. A programme of extensive tests was carried out in the Reverberation Chamber and North Transmission Chamber of Sound research Laboratories Limited, Holbrook Hall, Sudbury, Suffolk, generally in accordance with BRITISH STANDARDS Nos. 4196, 477, 4856, 4857 and This independent test facility is approved under the NAMAS Scheme. From the selection of a duct velocity within the operational parameters of the damper a resultant pressure drop from the Pressure Drop Vs Velocity table can be determined and the sum of these two components applied to the Velocity x Pressure Drop Vs Sound Level Graph. The graph is the result of a full range of acoustic tests on HotShield PTC High Operating Temperature Smoke Management and Fire Dampers with the blades set in the fully open position. The Spectrum Correction Data is applied to the number obtained from the graph and a complete Sound Spectrum of Flow Generated Noise for both Outlet (in duct) and Breakout (casing radiated) is obtained. Example: Duct with a design velocity of 8m/sec HotShield PTC damper Series 501 fully open Pressure Drop = Pa Multiply Velocity x Pressure Drop 8 x = 176 From Sound Graph plot 176 on horizontal Velocity/Pressure axis against 501 outlet (induct) graph to obtain 47 dbw on Vertical Sound Level Axis. Add or subtract corrections to the 47 dbw to provide full spectrum analysis. Velocity (m/s) x Pressure Drop (Pa) Vs Sound Level (dbw) SOUND POWER LEVEL (dbw) Pressure Drop Vs Velocity PRESSURE DROP (Pa) EXAMPLE LINE 0 EXAMPLE LINE TYPE 50 1 TYPE VELOCITY (m/s) 501 BREAKOUT 601 BREAKOUT Leakage Data at Ambient Temperature (Cold smoke) Note: Damper Leakage HotShield PTC and HotShield Vent PTC closed blade leakage as tested on a damper 1000mm wide x 1000mm high. The leakage was achieved after a total immersion test at 00 C for 1 hour (as witnessed by the Loss Prevention Council). HotShield PTC Outlet (Induct) Spectrum Corrections Octave Band k k 4k 8k Hz Series db Series db HotShield PTC Breakout Spectrum Corrections OUTLET (INDUCT) VELOCITY X PRESSURE DROP (m/s Pa) 501 OUTLET (INDUCT) Octave Band k k 4k 8k Hz Series db Series db PRESSURE DIFFERENTIAL ACROSS CLOSED DAMPER (Pa) LEAKAGE (I/s) 15

16 Specification HotShield PTC High Operating Temperature Smoke Management and Fire Dampers Comprising of 75mm stainless steel aerodynamic interlocking blades incorporating a high temperature synthetic seal, with stainless steel blade end bearings and peripheral gasketing. Housed in a galvanised fully welded, spigotted casing suitable for square, rectangular, circular or flat oval connections. The totally enclosed precise movement opposed blade drive shall be positioned out of the airstream for protection against damage, be hard wearing and free running. The Control Mode/Damper connection shall be by means of the snaplock drive interface mechanism, which is totally independent of the ductwork. HotShield PTC High Operating Temperature Smoke Management and Fire Dampers in association with their appropriate insulated control modes shall be arranged for motor open and spring closed operation interfaced with a smoke detection/fire alarm system. HotShield PTC Damper and selected thermally insulated Control Modes (HM5 and HM6) as supplied by Actionair. HotShield Vent PTC High Operating Temperature Smoke Control and Extract Dampers Comprising of 75mm stainless steel aerodynamic blades incorporating a high temperature synthetic seal, with stainless steel blade end bearings and peripheral gasketing. Housed in a galvanised fully welded, spigotted casing suitable for square, rectangular, circular or flat oval connections. The totally enclosed precise movement opposed blade drive shall be positioned out of the airstream for protection against damage, be hard wearing and free running. The Control Mode/Damper connection shall be by means of the snaplock drive interface mechanism, which is totally independent of the ductwork. HotShield Vent PTC High Operating Temperature Smoke Control and Extract Dampers in association with their appropriate insulated control modes shall be arranged for motor close and spring open operation interfaced with a smoke detection/fire alarm system. HotShield Vent PTC Damper and selected thermally insulated Control Modes (HVM5 and HVM6) as supplied by Actionair 16 Approvals Heat Degradation test witnessed by the Loss Prevention Council. Complies with the latest DW 144 casing leakage specification. HotShield PTC dampers when closed have up to four hours fire resistance when tested to BS476 Parts 0 and. The insulated Control Modes satisfy the requirements of EN and EN electro magnetic compatibility. Customer Service Actionair provides quality products backed by a dedicated team committed to providing the very best in customer service. Offering experienced technical backup, comprehensive sales and administrative customer support, product commissioning and maintenance service Maintenance The HotShield PTC dampers are designed for applications in normal dry filtered air systems and should be subjected to a planned inspection programme, with cleaning and light oil lubrication in accordance with BS9999. When exposed to fresh air intakes and/or inclement conditions this may need to be performed more regularly based on experience gained from previous inspections.

17 Ordering Information Example Quantity Series Acessories Duct Size Control Mode HS501 I/F 600(W) x 400(H) HM6 H Number of units required HS501/PTC HotShield PTC Square or Rectangular (Motor Open/Spring Closure) HS601/PTC HotShield PTC Circular (Motor Open/Spring Closure) HS701/PTC HotShield PTC Flat Oval (Motor Open/Spring Closure) HSV501/PTC HotShield Vent PTC Square or Rectangular (Motor Close/Spring Opening) HSV601/PTC HotShield Vent PTC Circular (Motor Close/Spring Opening) HSV701/PTC HotShield Vent PTC Flat Oval (Motor Close/Spring Opening) DWFX-F Dry Wall Fixing System Flange plus Cleats DWFX-C Dry Wall Fixing System Cleats I/F HEVAC / HVCA Installation Frame S&A Sleeve and Angle Nominal Damper Spigot Size HM5 PTC HM6 PTC HMV5 PTC Vent HMV6 PTC Vent HM5-P PTC HMV5-P PTC Vent HM5-P PTC HM6-P PTC HDI Enclosure H 17

18 Actionpac Control Panels Actionpac LNS4 - Bespoke The Actionpac LNS4 System consists of an embedded computer, UPS and preloaded software. The system communicates with damper interfaces to provide bespoke intelligent control and monitoring of motorised dampers and monitoring of manual fire dampers. The data network cabling enables substantial reduction in costs when compared with conventional systems. Digital inputs and outputs can be accommodated on the network cable or located within the panel enclosure. The embedded computer is supplied with Actionpac LNS4 software which is extremely user friendly. The server architecture delivers new benefits such as flexibility, reduced commissioning time, ease of configuration, simplified operation, future system growth, full diagnostics for system and device integration along with optional automatic scheduled damper testing. Actionpac Electro Mechanical Smoke and Fire Damper Hard Wired Control Panels 18 EMS Standard y Control and monitoring system. y Actionpac Electro Mechanical Smoke and fire damper control system. y Automatic damper operation utilising relay logic and LED indication of damper status. y Standard Modular Construction. y LED indication of damper status. y Mains isolator. y Test/Normal/Override Key-switch. y Lamp test facility. y Two Versions (Mode 5 and Mode 6), available in two sizes, from Stock. EMB Bespoke y Control and monitoring system. y Actionpac Electro Mechanical Smoke and fire damper control system. y Automatic damper operation utilising relay logic and LED indication of damper status. y Features y Customised central Control Panel. y Individual, or collectively controlled and continually monitored. y Wall mounted enclosure to IP55. y Custom Engraved Traffolyte fascia. y LED indication of damper status. y Miniature circuit breaker protection. y Options y Lockable glazed door. y Special paint finish to BS standard colour reference numbers. y Flush mounting flanges. y Latching push buttons. y Fireman s override key switches. y Test Switch. y Lamp Test. y Audible alarm with mute facility. y B.M.S. Common fault relay interface. y B.M.S. Output. y Delay timers. y Battery backup. Specialist Panels available y Fan Control Panel. y Fireman s control panel. y Mimic (Repeater) Panel y Fire damper monitor (Indication) panel. y Zonal inputs. y Door interlocking isolator.

19 Typical Network Schematic ROOF NETWORK NDI404 VFC INPUT TO MCC AHU AIR HANDLING UNIT LEVEL LEVEL NETWORK LEVEL 1 NETWORK 4 NETWORK 5 GROUND LNS4 VFC Fire Alarm Inputs As Required Fireman s Override Panel BASEMENT H H NETWORK 1 H H HP 19 Note: Each damper interface controls/monitors a damper.

20 actionair air-diffusion airfiltrera airolution naco South Street, Whitstable, Kent, CT5 DU Tel: +44 (0) Website: actionair.co.uk The statements made in this brochure or by our representatives in consequence of any enquires arising out of this document are given for information purposes only. They are not intended to have any legal effect and the company is not to be regarded as bound thereby. The company will only accept obligations, which are expressly negotiated for and agreed and incorporated into a written agreement made with its customers. Due to policy of continuous product development the specification and details contained herein are subject to alteration without prior notice. LNNN001 (1.0)