NIBCO Press System Bronze Ball Valves Two-Piece Body Full Port Bronze Trim Blowout-Proof Stem

Transcription

1 AHEAD OF THE FLOW NIBCO Press System Bronze Ball Valves Two-Piece Body Full Port Bronze Trim Blowout-Proof Stem Dezincification Resistant Revised 1/6/ PSI/17.2 Bar Non-Shock Cold Working Pressure 250 F Maximum Operating Temperature CONFORMS TO MSS SP-110 MATERIAL LIST Specification Part 1. Body Bronze ASTM B584 Alloy C Body End Bronze ASTM B584 Alloy C Press End Adapter (2) Wrot Copper ASTM B75 Alloy C Ball Brass ASTM B16 Alloy C36000 or ASTM B283 Alloy C37700 (Chrome/Nickel Plated) 5. Seat Ring (2) Reinforced PTFE 6. Boss seal o-ring (2) EPDM 7. O-Ring (2) EPDM 8. Packing PTFE 9. Pack Gland Brass ASTM B16 Alloy C Stem Silicon Bronze ASTM B371 Alloy C69430 or ASTM B371 Alloy C Handle Nut Zinc Plated Steel 12. Thrust Washer Reinforced PTFE 13. Handle Assembly Zinc Plated Steel with Plastisol Coating PC Press x Press Female End DIMENSIONS WEIGHTS Dimensions SIZE A B C D E Weight In. mm. In. mm. In. mm. In. mm. In. mm. In. mm. Lbs. Kg. 1/ / / / NIBCO Press System ball valves are designed to meet MSS SP-110 with the exception of the end connection. Ball valves are down-rated from 600 PSI CWP to 250 PSI CWP to match the Press System. Male and female press-to-connect ends are new technology not yet covered in the current edition of this specification. PC P x P Handle Options: Stainless Steel Lever NIB-Seal Locking lever Stainless Steel Locking Lever Memory stop Extended lever w/ memory stop Round Wing Horizontal and vertical chain NIBCO INC. WORLD HEADQUARTERS 1516 MIDDLEBURY ST. ELKHART, IN USA PH: TECH SERVICES PH: FAX: INTERNATIONAL OFFICE PH: FAX:

2 AHEAD OF THE FLOW Class 125 Bronze Ring Check Valves Inline Lift Type Resilient Discs Spring Actuated Revised 7/3/2012 Dezincification Resistant 125 PSI/8.6 Bar Saturated Steam to 353 F/178 C (PTFE Disc) 250 PSI/17.2 Bar Non-Shock Cold Working Pressure MATERIAL LIST Specification Part 1. Body Bronze ASTM B 584 Alloy C Stem Stainless Steel ASTM A 582 Alloy C Spring 316 Stainless Steel 4. Disc Holder Stainless Steel Type Disc Water, Oil or Gas (Buna-N) Steam (PTFE) (Y) 6. Seat Screw Stainless Steel ASTM A 276 Alloy S Body End Bronze ASTM B 584 Alloy C84400 T-480 Threaded S-480 Solder DIMENSIONS WEIGHTS QUANTITIES Dimensions Size A B C T-480 S-480 Master In. mm. In. mm. In. mm. In. mm. Lbs. mm. Lbs. Kg. Ctn. Qty. ³ ₈ ¹ ₂ ³ ₄ ¹ ₄ ¹ ₂ Ordering: The T-480 and S-480 both have standard Buna-N Discs. Also available with PTFE (Y) Discs; specify T-480-Y or S-480-Y. ³ ₈" thru 2" require ¹ ₂ pound pressure to open. T-480-Y (PTFE Disc) NPT x NPT S-480-Y (PTFE Disc) C x C NIBCO Check Valves may be installed in both horizontal and vertical lines with upward flow or in any intermediate position. u For detailed Operating Pressure, refer to Pressure Temperature Chart on page 113. Warning Do Not Use For Reciprocating Air Compressor Service. 36 NIBCO INC. WORLD HEADQUARTERS 1516 MIDDLEBURY ST. ELKHART, IN USA PH: TECH SERVICES PH: FAX: INTERNATIONAL OFFICE PH: FAX:

3 LMR PLUS Electric Fire Pump Controllers Electrical Wiring Schematic FD30 Across-the-Line May 2011 Electrical Wiring Schematic LMR PLUS REMOTE START DELUGE VALVE (REMOVE JUMPER IF USED) PUMP START LOW SUCTION LOW ROOM TEMPERATURE INTERLOCK ON INPUT #1 INPUT #2 INPUT #3 INPUT #4 INPUT #5 INPUT #6 INPUT #7 INPUT #8 INPUT #9 CUSTOMER INPUTS OPTION RELAY #1 (2 SETS FORM-C) OPTION RELAY #5 (2 SETS FORM-C) OPTION RELAY #2 (2 SETS FORM-C) OPTION RELAY #6 (2 SETS FORM-C) OPTION RELAY #3 (2 SETS FORM-C) OPTION RELAY #7 (2 SETS FORM-C) OPTION RELAY #4 (2 SETS FORM-C) OPTION RELAY #8 (2 SETS FORM-C) COMMON ALARM (NORMALLY ENERGIZED) COMMON ALARM (NORMALLY ENERGIZED) PHASE FAILURE (NORMALLY ENERGIZED) PHASE FAILURE (NORMALLY ENERGIZED) PHASE REVERSAL PHASE REVERSAL ALARM CONTACTS INTERNAL CONNECTIONS FUTURE #1 FUTURE #1 PUMP RUN PUMP RUN N. Y. C. APPROVED ES K/D For more information visit:

4

5 LMR PLUS Electric Fire Pump Controllers Field Connections FD30 Across-the-Line September 2013 Field Connections Line Terminals (Incoming Cables) Load Terminals (To Motor) External Inputs * Qty. & Cable Sizes Max HP (1)#14-1/0 PER Ø (CU/AL) (1)#14-2/0 (CU/AL) (1)#4-4/0 PER Ø (CU) (1)#4-350MCM (CU/AL) (1)#3-350MCM PER Ø (CU/AL) (1)#4-350MCM (CU/AL) (2)3/0-250MCM PER Ø (CU/AL) (2)1/0-750MCM (CU/AL) (2) MCM PER Ø (CU/AL) (2)1/0-750MCM (CU/AL) * Coils available: 380V-50Hz, 380V-60Hz, 415V-50Hz, 415V-60Hz. Max HP Line Terminals on Main Isolation Switch (Incoming Cables) LINE VOLTAGE Load Terminals (To Motor) Line Voltage Qty and Cable Sizes Single Run Double Run Alarm / Relay Outputs LMR Service Entrance GND. LUG Qty. & Cable Sizes (1) #14 - #8 PER (CU/AL) (2) #14 - #8 PER (CU/AL) (1) #14 - #1 PER (CU/AL) (2) #14 - #2 PER (CU/AL) (1) #8-3/0 PER (CU/AL) (2) #8-2/0 PER (CU/AL) (1) #2-750MCM PER (CU/AL) (2) 1/0-250MCM PER (CU/AL) (1) 1/0-500MCM PER (CU/AL) (2) 1/0-500MCM PER (CU/AL) For ambient temperatures above 30C (86F), the temperature rating of motor conductors is recommended to be a minimum of 90C (194F) For Proper Cable Size Refer to National Electrical Code NFPA-70 PLUS COMMON ALARM (NORMALLY ENERGIZED) COMMON ALARM (NORMALLY ENERGIZED) PHASE FAILURE (NORMALLY ENERGIZED) PHASE FAILURE (NORMALLY ENERGIZED) PHASE REVERSAL PHASE REVERSAL ALARM CONTACTS FUTURE #1 FUTURE #1 PUMP RUN PUMP RUN NOTE: 1. MOTOR CONNECTIONS VARY, PLEASE REFER TO SPECIFIC MOTOR CONNECTION DIAGRAM. 2. PLEASE OBSERVE PROPER PHASE ROTATION, A,B,C-L1,L2,L3 AS CONTROLLER IS PHASE SENSITIVE. 3. CABLE SIZE TO BE 125% OF FULL LOAD CURRENT. REFER TO WIRE SIZE TABLE IN NFPA 70. N. Y. C. APPROVED ES K/E For more information visit:

6 Must Be Installed Per Applicable Code and Manufacturers Recommendations 3A13357H01 3A13357H01 START STOP LMR PLUS Electric Fire Pump Controllers Dimensions FD30 Across-the-Line July 2011 Dimensions Standard Enclosure - Type NEMA 2, 3R, 4, 4X, 12 LMR PLUS [317] [721] [564] [254] [1270] [1219] [1524] 5.25 [133] 2.63 [67] Ø1.75 [Ø44] [305] 6.00 [152] [267] PIPING ENTRANCE 1/4" NPT - FEMALE 5.00 [127] PIPING ENTRANCE 1/2" NPT - FEMALE 6 Dimensions in inches and [millimeters]. 1 - START PUSHBUTTON 2 - STOP PUSHBUTTON 3 - MAIN POWER SWITCH 4 - MSH (EMERGENCY START HANDLE) 1.12 [28] 5 - MAIN LMR PLUS DISPLAY 6 - RECOMMENDED CABLE ACCESS (BOTTOM ONLY) [337] 4.24 [108] 1.14 [29] 3.32 [84] 2.09 [53] 8.42 [214] Motor Hp Line Voltage V V * V V * Coils Available: 380V-50Hz, 380V-60Hz, 415V-50Hz, 415V-60Hz Withstand Rating Standard Intermediate High 100, , , (81) V 25, ,000 Approx. Weight Lbs. (Kg) N. Y. C. APPROVED SEISMIC QUALIFIED U.B.C and C.B.C NOTES: 1. All enclosures finished in FirePump red. 2. Cable Entrance bottom only. 3. Standard Enclosure type NEMA 2. MD K/C For more information visit:

7 Must Be Installed Per Applicable Code and Manufacturers Recommendations LMR PLUS Electric Fire Pump Controllers Main Display Main Display - LMR Plus Fire Pump Controllers June 2011 Main Display LMR PLUS SILENCE ALARM MOTOR TEST POWER ON PUMP RUNNING LOCAL START REMOTE START DELUGE VALVE EMERGENCY START INTERLOCK ON LOW PRESSURE AUTO SHUTDOWN ENABLED PHASE REVERSAL PHASE FAILURE FAIL TO START UNDERVOLTAGE OVERVOLTAGE LOW ROOM TEMPERATURE LOCKED ROTOR TRIP LOW SUCTION PRESSURE SOURCE 2 DISCONNECTED LMRPLUS DATA PRINT LAMP TEST MENU RESET SAVE/EXIT ACK NOTES: 1. Refer to the LMR Plus technical manual for detail and setup information, as well as programming and custom labelling for Programmable LED # 1 and Programmable LED # 2. N. Y. C. APPROVED SEISMIC QUALIFIED U.B.C and C.B.C NOTE: As of January 1, All Limited Service Controllers will not carry FM Approval. MD K/D For more information visit:

8 DIFFERENTIAL PRESSURE Multi-Sense Model 231 Wet-to-Wet, Differential, Multi-Configurable Pressure Transducer NOTE: Setra quality standards are based on AN- SI-Z The calibration of this product is NIST traceable. U.S. Patent nos ; DESCRIPTION Setra s Model 231 Multi-Sense Wet-to-Wet differential pressure transducer all-inclusive design provides users with field accessible ranging, choice of output and field zeroing. Choose from three configurable pressure transducers: 5 up to 50 psid, 10 up to 100 psid, or 25 up to 250 psid. Each Model 231 has 4 unidirectional and 4 bidirectional switch selectable pressure ranges and can be reconfigured in the field for 0-5 VDC, 1-5 VDC, VDC, or 4 to 20 ma output. The Model 231 jumper selectable port swap feature eliminates costly replumbing if the pressure transducer is improperly installed or replaced. An optional LCD display is available for on-site indication of line and differential pressure. SPECIFICATIONS FEATURES Field Selectable Output - True 4 to 20 ma, 0 to 5, 1 to 5, and 0 to 10 VDC Field Selectable Pressure Ranges Field Accessible Push-Button Zero and Remote Zero Dual Sensors Optional 3- or 5-Valve Manifold Hinged Cover Field Selectable Port Swap Optional LCD Display All Cast Aluminum, NEMA4 Rated Housing CE and RoHS Compliant APPLICATIONS Energy Management Systems Process Control Systems Flow Measurement of Various Gases or Liquids Liquid Level Measurement of Pressurized Vessels Pressure Drop Across Filters Electrical Data (Voltage) Performance Data Environmental Data Circuit 3-Wire Accuracy RSS 1 (at constant temp.) Operating 3 Temperature F ( C) -4 to +185 (-20 to -85) Excitation 15 to 30 VDC/18 to 30 VAC (Reverse Excitation Protected) Pressure Ranges A, B, C ±1.0% FS Storage Temperature F ( C) -4 to +185 (-20 to +85) Output 4 0 to 5 VDC, 0 to 10 VDC, 1 to 5 VDC Pressure Ranges D ±2.0% FS Vibration 10g from 50Hz to 2000 Hz Output Impedance 30 Ohms Pressure Ranges Shock 200g Circuit Consumption 8 ma (typ.) at 5 VDC, 8 ma (typ) at 10 VDC40 ma (typ.) at VAC A B C D Max. Line Pressure Physical Description MS Case Die Cast Aluminum, Powder Coated Electrical Data (Current) MS Pressure Fittings 1/8-18 NPT Internal Curcuit 2-wire (Reverse Excitation Protected) MS Electrical Connection 1/2 in. Conduit Output 5 4 to 20 ma Pressure Media Size 4.0 x 6 x 2 in. (102 x 152 x 51 mm) External Load Min. Supply Voltage (VDC) 0 to 250 Ohms x (Resistance of reciever plus line). Liquids or Gases Compatible with 17-4 PH Stainless Steel Note: Hydrogen not recommended for use with 17-4 PH stainless steel 1 RSS of Non-Linearity, Hysteresis, and Non-Repeatability. 2 Units calibrated at nominal 70 F. Maximum thermal error computed from this datum. 3 Operating temperature limits of the electronics only. Pressure media temperatures may be considerably higher or lower. 4 Calibrated into a 50K ohm load, operable into a 5000 ohm load or greater. 5 Calibrated at factory with a 24 VDC loop supply voltage and a 250 ohm load. Specifications subject to change without notice. Weight Sensor Vacity Volume Max. Supply Voltage (VDC) (Resistance of reciever plus line). Thermal Effects lb 0.2 cc Compensated Range F ( C) +32 to +130 (0 to +54) Zero/Span Shift %FS/100 F (50 C) 2.0 (1.8) Warm-up Shift Response Time Proof Pressure <0.12% FS 1 to 5 sec. (selectable) Burst Pressure 15 x Full Scale (50 psi), 10 x Full Scale (75 x 150 psi), 8 x Full Scale (250 psi) 1 Phone: Fax: setra.com 2013 Setra Systems, Inc. All rights reserved. The Setra Systems name and logo are registered trademarks of Setra Systems, Inc. 2 x Full Scale

9 DIMENSIONS R Multi-Sense Model 231 Wet-to-Wet, Differential, Multi-Configurable Pressure Transducer WIRING DIFFERENTIAL PRESSURE DC/AC Power Supply Controller Voltage Relay /8 NPTF High Low Wire - Voltage Output 0 to 5 VDC 0 to 10 VDC 1 to 5 VDC Remote Zero 1/2 Conduit Opening DC Power Supply + Controller Current (4-20 ma) Relay Wire - Current Output 4 to 20 ma Remote Zero IN MM 2013 Setra Systems, Inc. All rights reserved. The Setra Systems name and logo are registered trademarks of Setra Systems, Inc. Phone: Fax: setra.com 2

10 DIFFERENTIAL PRESSURE Multi-Sense Model 231 Wet-to-Wet, Differential, Multi-Configurable Pressure Transducer DIMENSIONS (3-Valve Manifold Assembly) 3-Valve Manifold Assembly Description (Order as Pressure Code Fitting "3V".) Manifold Block Valves (3) Valve type Brass V1 for connection to +port V2 for connection to -port V3 for equalizing pressure 90 Degree On/Off Process Connections 1/4-18 NPT Internal Thread MODEL 230 DIFFERENTIAL PRESSURE TRANSDUCER V3 SHUNT VALVES V1 V1 V2 V2 SHUT OFF VALVES HIGH PROCESS CONNECTION 1/4'' NPT LOW PROCESS CONNEC- TION 1/4'' NPT For differential pressure measurements at high line pressure (250 psig max), it is recommended that the pressure sensor be installed with a valve in each line, plus a shunt valve across the high and low (reference) pressure ports as shown DIMENSIONS (5-Valve Manifold Assembly) 5-Valve Manifold Assembly Description (Order as Pressure Code Fitting 5V.) Manifold Block Valves (5) Valve Type Process Connection Brass V1 for connection to ±port V2 for connection to -port V3 for equalizing pressure V4 for connection to external gauge or alternate plumbing configuration V5 for connection to external gauge or alternate plumbing configuration 90 Degree On/Off 1/4-18 NPT Internal Thread V6 V7 Model 230 Differential Pressure Transducer SHUNT VALVE V4 V1 High Process Connection 1/4 NPT V3 V2 V5 Low Process Connection 1/4 NPT SHUT OFF VALVES Low Process/Commission 1/4 NPT Connection Phone: Fax: setra.com 2013 Setra Systems, Inc. All rights reserved. The Setra Systems name and logo are registered trademarks of Setra Systems, Inc.

11 INSTALLATION Valve A 1 High Multi-Sense Model 231 Wet-to-Wet, Differential, Multi-Configurable Pressure Transducer High Pressure Remote Sensor Pipe Model 231 Valve A = High Side Valve Valve B = Low Side Valve 1. Valves not included. Low Pressure Remote Sensor Pipe Valve B 1 Low DIFFERENTIAL PRESSURE PRESSURE RANGE CODE SELECTOR (IMPORTANT: READ BEFORE ORDERING) Examine the pressure application and determine what is the Highest System Line Pressure. Determine what is the Differential Pressure being measured. Find the MAX. Line Pressure in the table on the right that is > to your Highest System Line Pressure. Verify that your DP falls within the selectable ranges in that row. Follow that row to the left and select that range code. Example: Highest System Line Pressure: Differential Pressure Measured: Max Line Pressure to System Line Pressure: Select Range Code: Range Code 125 psig 50 psid 250 psid (50 psid DP falls within ranges in this row) MS3 A B C D Max. Line Pressure MS MS MS ORDERING INFORMATION G Model Range Code Pressure Connection Display 231G = 231G See Table 1 Below Std. 2F 1/8-18 NPT female (Standard) Sensor (Conduit Version) Table 1. Range Specification* RANGE CODE UNIDIRECTIONAL PRESSURE RANGES BIDIRECTIONAL PRESSURE RANGES MS1 5, 10, 25, 50 psid ±5, ±10, ±25, ±50 psid MS2 10, 20, 50, 100 psid ±10, ±20, ±50, ±100 psid MS3 25, 50, 125, 250 psid ±25, ±50, ±125, ±250 psid *Note: Maximum line pressure is maximum range of pressure ordered. Std. N No Display Opt. 3V 3-V Manifold assembled w/ Model 231 Opt. D LCD Display Opt. 5V 5-V Manifold assembled w/ Model 231 Ordering Example: 231GMS12FD = Model 231, 5 PSID up to 50 PSID, 1/8 NPT Female Fitting, and LCD Display 31GMS13VN= Model 231, 0 to 5 psid up to 50 PSI, 3-Valve Manifold, and No LCD Display SSP231 Rev.D 05/21/ Setra Systems, Inc. All rights reserved. The Setra Systems name and logo are registered trademarks of Setra Systems, Inc. Phone: Fax: setra.com 4

12

13

14

15 Type 1005P, XUL Fire Protection Sprinkler Service Gauge Triple Scale Dials NOW Available FEATURES Underwriters Laboratory listed and Factory Mutual approved Corrosion-resistant ABS case Heat-resistant polycarbonate push-in window Patented PowerFlex movement with polyester segment True Zero indication, a unique safety feature Ashcroft fire protection sprinkler gauges are Underwriters Laboratory listed and Factory Mutual approved for fire protection sprinkler service. The case material on Type 1005P, XUL gauges is ABS. The psi pressure range is used on wet systems where water is available to the sprinkler heads. The 0-80 retard to 250 psi pressure range is used on dry systems where the lines are filled with air pressure until system activation. The psi gauge is available for systems requiring higher pressures. Due to global demands for fire protection sprinkler gauges, Ashcroft offers UL listed, triple scale (bar, kpa, psi) dial gauges. The patented PowerFlex movement with polyester segment is designed to provide unequalled shock and vibration resistance resulting in superior performance and extended gauge life. True Zero indication, a standard feature on these gauges, reduces the potential risk of installing a damaged gauge on your equipment. PRODUCT SPECIFICATIONS Ashcroft Model No.: 1005P, XUL Accuracy: ASME B Grade B (±3-2-3% of span) Size: 3 1 /2 Case: ABS (Polycarbonate blend) Ring: None Window: Polycarbonate, push-in Dial: Black figures on white background Pointer: Black, aluminum Bourdon tube: C shaped bronze Movement: Patented PowerFlex with polyester segment Socket: Brass Restrictor: None Connection: 1 4 NPT lower Ranges: Single, dual or triple scale psi (water) 0-80 retard to 250 psi (air) psi Operating temperature: 40 F to 150 F; 40 C to 65 C UL 393 Listed, UL of Canada Listed and FM approved. Equivalent (single or dual scale) metric scales are available OPTIONAL FEATURES Customized dials Other UL listed ranges on application Black Rubber Gauge Boot Shown with Optional Rubber Boot HOW TO ORDER (Typical example) 35 W 1005 P H 02L XUL 300# Dial Size: 3 1 /2 Movement: Patented PowerFlex Case Type Number: 1005P Case Material: ABS Socket Material: Brass Connection Size/Location: 1 /4 NPT Lower Listing: UL listed, FM approved Range: 0/300 psi BULLETIN CSG-3 All specifications are subject to change without notice. All sales subject to standard terms and conditions. Ashcroft Inc /14 Ashcroft Inc., 250 East Main Street, Stratford, CT USA Tel: Fax: info@ashcroft.com

16 Type 1005P, XUL Fire Protection Sprinkler Service Gauge DIMENSIONS A B D C G 1/4 NPT E SIZE/TYPE A B C D E G Weight oz 1005P, XUL (94) (29) (69) (92) (11.9) (14.2) kg BULLETIN CSG-3 All specifications are subject to change without notice. All sales subject to standard terms and conditions. Ashcroft Inc /14 Ashcroft Inc., 250 East Main Street, Stratford, CT USA Tel: Fax: info@ashcroft.com

17 Fire Pump Controllers 1-1 Features LMR Plus Electric Fire Pump Controllers Typical Specifications 1. Approvals A. The Fire Pump Controller shall meet the requirements of the latest edition of NFPA 20 and shall be listed by [Underwriters Laboratories (UL)]and approved by [Factory Mutual Research (FM)] [Canadian Standards Association (CSA)] [New York Department of Buildings (NYSB)] and carry the CE marking for fire pump service. 2. Starting Type A. The controller shall be of the combined manual and automatic type designed for [Full Voltage Starting] [Part Winding Starting] [Primary Resistor Starting] [Autotransformer Starting] [Wye-Delta (Star-Delta) Open Transition Starting] [Wye-Delta (Star-Delta) Closed Transition Starting] [Solid State Soft Start Starting] 3. Ratings A. The Controller shall have a withstand rating of 100,000 RMS symmetrical [208V] [240V] [380V] [400V] [415V] [480V] 600VAC]. 4. Construction A. The controller shall include a motor rated combination isolating switch and circuit breaker, mechanically interlocked and operated with a single externally mounted handle. B. The isolating switch shall be rated to disconnect the motor load. C. The isolating switch/circuit breaker combination shall be mechanically interlocked such that the enclosure door cannot be opened when the handle is in the on position except by a tool operated defeater mechanism. D. The controller manufacturer shall manufacture the contactor, isolating switch, circuit breaker, pushbuttons, and enclosures. Brand-labeled components will not be accepted. 5. Enclosure A. The controller shall be housed in a NEMA Type 2 (IEC IP11) drip-proof, powder baked finish, freestanding enclosure. B. Optional Enclosures: 1. NEMA 3R (IEC IP14) rain-tight enclosure. 2. NEMA 4 (IEC IP66) watertight enclosure. 3. NEMA 4X (IEC IP66) watertight 304 stainless steel enclosure. 4. NEMA 4X (IEC IP66) watertight 316 stainless steel enclosure. 5. NEMA 4X (IEC IP66) watertight corrosion resistant enclosure. 6. NEMA 12 (IEC IP52) dust-tight enclosure. 6. Microprocessor Control A. The controller shall come complete with a 4 line by 40 character LCD display mounted on a panel opening in the front door. The LCD display shall indicate the following: 1. Main screen displaying system pressure, threephase voltage and amperage readings, system frequency, date, and time. 2. Set point review screen displaying the programmed pressure start and stop points, and weekly test time. 3. Controller statistics screen, including: a. Powered Time b. Motor Run Time c. Number of Calls to Start d. Number of Starts e. Last Motor Start Time f. Last Motor Run Time g. Last Low Pressure Start h. Minimum System Voltage i. Maximum System Voltage j. Minimum System Frequency k. Maximum System Frequency l. Minimum System Pressure m. Maximum System Pressure n. Last System Startup o. Last Phase Failure p. Last Phase Reversal q. Last Locked Rotor Trip r. Maximum Run Current s. Last Locked Rotor Current 4. Controller diagnostics screen, including: a. Date & Time b. Firmware Version c. Shop Order Number d. Customer Order Number e. Transformer Output Voltage f. Current Transformer Outputs g. Pressure Transducer Calibrated Settings h. Input Status i. Output Status 5. Display last messages screen that will display up to 10,000 alarms/messages stored in the controllers' memory. 6. Display up to ten (10) custom messages of up to 100 characters each, which will continually scroll across the fourth line of the display. 7. Remaining time left on active timers. B. The controller shall be supplied with ten (10) green status LED s for the following: 1. Power On 2. Pump Running 3. Local Start 4. Remote Start 5. Deluge Valve 6. Emergency Start July 2011 For more information visit: PS K/E

18 Fire Pump Controllers 1-2 Features LMR Plus Electric Fire Pump Controllers 7. Interlock On 8. Low Pressure 9. Auto Shutdown Enabled 10. Programmable LED #1 C. The controller shall be supplied with ten (10) red alarm LED s to indicate the following: 1. Phase Reversal 2. Phase Failure 3. Fail to Start 4. Undervoltage 5. Overvoltage 6. Low Room Temperature 7. Locked Rotor Trip 8. Low Suction Pressure 9. Source 2 Disconnected 10. Programmable LED #2 D. The microprocessor logic board shall be available with: 1. A USB port for transference of message history, controller status, diagnostics, and statistics and the ability to update firmware. 2. An optional Ethernet port for direct connection to a computer for data transfer. 3. An optional RS485 Serial port for communication to various external software programs. E. The controller shall be available with an embedded web page to allow viewing of the controllers' current status, data values, programmed set points, and history. F. A Fail-to-Start alarm shall occur if the motor controller sees less than 20% of the motor full load amps after an adjustable time delay of 1-90 seconds. G. Locked rotor protection shall be provided. After a trip condition and restoration of power, the LCD display shall indicate LOCKED ROTOR TRIP. H. A sequential start timer and weekly test timer shall be provided as standard. I. A restart time delay of two (2) seconds shall be provided to allow the residual voltage of the motor to decay prior to re-starting the motor. In the event that the pump motor continues to run after a request to stop, then the controller must display a fail to stop message to indicate this condition. J. Overvoltage (5-20%) and undervoltage (5-30%) sensing and alarming shall be provided as standard. K. The controller shall be supplied with interlock and shutdown circuits as standard. A flashing green LED shall indicate an interlock on condition. L. Where shutdown of the pump(s) due to low suction pressure is required, it shall be accomplished without the addition of a separate panel or enclosure. The LCD display shall indicate low suction shutdown. Resetting of the condition shall be automatic or manual as selected by the user. M. Means shall be provided to test the operation of all LED s to ensure their functionality. 7. Programming Menu A. The programming menu shall have the ability to enable an entry password. B. The programming menu shall be limited to two (2) levels of password protection. C. The controller shall have three (3) languages as a standard, English, French, and Spanish, with the ability to add a fourth language. D. The programming menu shall be grouped into 6 main menu headings as follows: 1. Regional Settings 2. Pressure Settings 3. Timer Values 4. Alarm Set points 5. Input/Output Menu 6. System Configuration (password protected) 8. Pressure Sensor A. A solid-state 4-20mA pressure sensor shall be provided. The pressure Start and Stop points shall be adjustable in increments of one (1) PSI. A low pressure pre-alarm, indicated with a flashing green LED, shall denote a potential pump starting condition and will remain lit once the pump has started to indicate the starting cause. 9. Custom Inputs/Outputs A. The controller shall come standard with nine (9) future inputs, two (2) future LED indicators, and one (1) future output, with the ability to add up to another 8 outputs via optional relay boards. B. The user shall be able to program the future inputs/outputs through the main programming menu. C. The inputs shall be selectable based on the following criteria: 1. User selected message or thirteen (13) predetermined messages. 2. Energize the common alarm relay when the input is received. 3. Link to a future relay and/or LED indicator. 4. Alarm latched until reset. 5. Normally open or closed input. 6. On-delay timer. D. The LED indicators shall be selectable based on the following criteria: 1. Indication based on a minimum of twelve (12) predetermined alarms or a custom input. E. The future relays shall be selectable based on the following criteria: 1. Output based on a minimum of twenty-seven (27) predetermined alarms, controller status or a custom input. 2. Latched until reset. 3. Energized under normal conditions. 4. On or off delay timer on the output. July 2011 For more information visit: PS K/E

19 Fire Pump Controllers 1-3 Features LMR Plus Electric Fire Pump Controllers 10. Alarm Relays A. All relays shall be of the plug-in type. An LED on the relay panel shall indicate the energized state of the relay. All relay contacts shall be 8A, 277VAC/30VDC. Two (2) sets of Form-C contacts shall be provided for each of the following: 1. Phase Reversal 2. Phase Failure 3. Common Alarm 4. Future #1 5. Pump Run. B. The Common Alarm and Phase Failure relays shall be energized under normal conditions. 11. Audible Alarm Buzzer An audible alarm buzzer, capable of being heard while the motor is operating, shall operate if Fail to Start, Hardware Malfunction or any Common Alarm condition exists. 12. Manufacturer A. The controller shall be of the LMR Plus type as manufactured by Eaton Corporation. July 2011 For more information visit: PS K/E

20 AHEAD OF THE FLOW Revised 7/3/2012 Class 125 Bronze Y-Strainers Screw-in Cap Tapped Cap w/ Blow-off Plug or Solid Cap 20 Mesh SS Screen or SS Perforated Screen 125 PSI/8.6 Bar Saturated Steam to 353 F/178 C 200 PSI/13.8 Bar Non-Shock Cold Working Pressure conforms to ANSI B (NPT) or B16.18 (solder) Part 1. Body MATERIAL LIST Specification Bronze ASTM B584 Alloy C84400 (Solder) Bronze ASTM B62 Alloy C83600 (Threaded) 2. Cap Bronze ASTM B62 Alloy C Gasket PTFE 4. Screen ASTM E Mesh Stainless Steel or ASTM E674 Perforated Stainless Steel 5. Plug Brass ASTM B16 Alloy C36000 or Bronze ASTM B584 Alloy C84400 End Connection Screen Cap S- Solder Mesh (STD.) A - Tapped Cap w/plug (STD.) T - Threaded Perforated B - Solid Cap T-221/222-A Threaded T-221/222-A Threaded S-221/222-A Solder DIMENSIONS WEIGHTS QUANTITIES Dimensions Size A B C D T-221 S-221 Master In. mm. In. mm. In. mm. In. mm. In. mm. Lbs. Kg. Lbs. Kg. Ctn. Qty. ¹ ₄ / ³ ₈ / ¹ ₂ / ³ ₄ / / ¹ ₄ / ¹ ₂ / ¹ ₂ / / T-221/222-B Threaded S-221/222-A Solder S-221/222-B Solder T-221/222-B Threaded S-221/222-B Solder NIBCO INC. WORLD HEADQUARTERS 1516 MIDDLEBURY ST. ELKHART, IN USA PH: TECH SERVICES PH: FAX: INTERNATIONAL OFFICE PH: FAX: