Technical Manual. ReSound Pulse CRT PS60-R & ReSound Pulse CRT LT PSS60-R

Transcription

1 Technical Manual ReSound Pulse CRT PS60-R & ReSound Pulse CRT LT PSS60-R GN ReSound as Global Technical Operations gto.gnresound.com Lautrupbjerg 9 DK-2750 Ballerup Denmark Service@gnresound.dk

2 Table of contents Features...3 Part list Final device...7 How to separate the HI...8 Microphone assembly...9 Hybrid connections...10 Coating instructions...11 Colour markers replacement...12 Test equipment Charger spares...15 Page 2 of 15

3 Description Functional Description The ReSound Pulse CRT (Canal Receiver Technology) is a receiver-in-the-ear model in the existing ReSound Pulse family. All features are identical to the sound tube based ReSound models, except from that the receiver is removed from inside the device housing behind the ear and instead placed at the edge of the tube inside the ear canal. Key features WarpTM high resolution compression New StabilizerTM DFS system SuperTuneTM intelligent rechargeability Directionality Environmental Steering automatic compressor tuning Virtual WindShieldTM wind noise reduction Multi-band noise reduction Low-level expansion Low Battery Warning Indicator Onboard AnalyzerTM DataLogging Standard Configuration Size 312 battery SmartStart power-up timer Battery door with integrated On/Off switch XReceivers w/sound tubes and domes in different sizes 3 standard colours: Medium blonde, marble grey & anthracite Fitting Requirements Aventa fitting software (2.3 or higher) CS63 Flex Strip programming cable HI-PRO, NOAHlink or SpeeLink As from s/n PULSE CRT is delivered with hybrid Coyote 3.1. PULSE LT will continue to have the Coyote 3.0 mounted. For further information please also check GTO Technical News Bulletin No available on GTOweb Page 3 of 15

4 Part List Item MICROPHONE, SUSPENSION,MIC,FRONT SUSPENSION,MIC,REAR SPRING,BAT,POSITIVE,PLATED SPRING,BAT,NEGATIVE,PLATED CONTACT,PROGRAMMING MODULE FLEX-HYBRID,C3.0,DENMARK FLEX-HYBRID,C3.1 FOR PS60-R ONLY PIN,LOCK Ø=0.6, L= RUBBER GLUE C GREASE MOLYKOTE FS COLOUR MARKER,RED COLOUR MARKER,BLUE COATING, EGC-1700, 100ML WIRE,ESW,RED,7X32U,12MM WIRE,ESW,RED,7X32U,8MM WIRE,ESW,RED,7X32U,16MM WIRE,ESW,GREEN,7X32U,9MM WIRE,ESW,GREEN,7X32U,16MM Item WIRE,ESW,GREEN,7X32U,11MM WIRE,ESW,BLUE,7X32U,9MM WIRE,ESW,AMBER,7X32U,9MM WIRE,ESW,AMBER,7X32U,12MM WIRE,ESW,GREEN,7X32U,12MM CERUSTOP FILTER (KIT) PIN REMOVAL TOOL CONNECTOR,CRT PROGRAMMING CABLE,RED PROGRAMMING CABLE,BLUE STRIP CS63/NWT/FLEXSTRIP(10Pk) STRIP CS63/NWT/FLEXSTRIP(25PK) KIT PROGRAMM. CABLE W/FLEX,RED KIT PROGRAMM. CABLE W/FLEX,BLUE SIMULATED BATT. PILL,SIZE TEST FIXTURE MEASUREMENT TOOL CRT XREC TEST TUBE CC SNAP-ON ADAPTOR DSA Page 4 of 15

5 Part list Filter, Front FILTER,MIC.FRONT.4PCS.MDM BL FILTER,MIC,FRONT,4 PCS,MR GREY FILTER,MIC,FRONT,4PCS,ANT Filter, Rear FILTER,REAR,312,4PCS,MBL FILTER,REAR,312,4PCS,MARBLE GR FILTER,REAR,312,4PCS,ANT Frame PS60-R FRAME,CRT,PTD,MDM BLONDE FRAME,CRT,PTD,ANTHRACITE* FramePSS60-R FRAME,CRT,PTD,MDM BLONDE FRAME,CRT,PTD,ANTHRACITE* *is used for both ANT and MGR HI HI COMPLETE - PS60-R Ver. 3.1 MEDIUM BLONDE MARBLE GREY ANTHRACITE HI COMPLETE - PSS60-R MEDIUM BLONDE MARBLE GREY ANTHRACITE Housing KIT PS60-R & PSS60-R BLACK MEDIUM BLONDE METALLIC MARBLE GREY BLACK METALLIC MEDIUM BLONDE METALLIC COOL GREY ANTHRACITE MONZA RED PURPLE/GREEN PURPLE/BLUE GOLDEN/GREEN BRONZE/BORDEAUX WIMBLEDON GREEN STEEL SILVER LAVA BLACK OCEAN BLUE To replace a housing or battery door or to change to another housing colour, a kit consisting of housing and battery door must be ordered Page 5 of 15

6 Part list Item Ear Box Containing: AXLE 0.68X4.8MM PIN REMOVAL TOOL MEASUREMENT COUPL. ADAPTOR,CRT UNIVERSAL ADAPTABLE RETENTION MEASUREMENT TOOL CRT OPEN DOME,5L OPEN DOME,7L OPEN DOME,10L OPEN DOME,5S OPEN DOME,7S OPEN DOME,10S TULIP DOME,L TULIP DOME,S XRECEIVER STANDARD UNIT XS 0-L XRECEIVER STANDARD UNIT XS 1-L XRECEIVER STANDARD UNIT XS 2-L XRECEIVER STANDARD UNIT XS 3-L XRECEIVER STANDARD UNIT XS 0-R XRECEIVER STANDARD UNIT XS 1-R XRECEIVER STANDARD UNIT XS 2-R XRECEIVER STANDARD UNIT XS 3-R XREC STD UNIT - PACKED XREC STD UNIT - UNPACKED Page 6 of 15

7 Final Device XREC to be plugged into the stud of the HI Filter removal tool Cerustop filter kit p/n Wax guard Page 7 of 15

8 How to separate the HI Remove the filter for back microphone Gently press out the two pins by using the pin removal tool and pull them out by using e.g. tweezers. Take out the battery door and pull out the frame. Filters are recommended to be replaced during any repair situation Pin removal tool p/n Page 8 of 15

9 Microphone Assembly Wire, amber 12 mm p/n Wire, green 12 mm p/n Front mic suspension Back mic suspension Wire, red 12 mm p/n IN - Use service tool (heat zink) when soldering the microphone wires. Make sure that the suspensions fit well to the sound studs/ports on the microphones. Make sure that wire insulation is undamaged. Brush EGC-1700 coating to the solder points and let dry for 15 sec - then brush once more. Note: Make sure that the microphone is turned right. The wires must be turned towards the back mic suspension as shown on the drawing. Page 9 of 15

10 Hybrid connections Battery springs Contact module MIC+ MIC IN MIC- Coyote No marking Coyote Black dot marking Contact module H8 H9 Contact module The layout of C3.0 and C3.1 is the same. For visual purpose the C3.1 is marked with black dots. Only PS60-R is mounted with hybrid C3.1. In a repair situation a hybrid C3.0 can be replaced to C3.1. The test system will automatically detect the hybrid version during test. NOTE: Please also see Technical News Bulletin No (available from GTOweb) which is describing the implementation of C3.1. BAT(-) /REC(+) REC(-) BAT(+) Furthermore the improved test fixture is described Page 10 of 15

11 Coating Cover the pins of the contact module at the solder points and at the in-mould. Press it under the contact pins to ensure good protection. Add molykote in the area indicated by the red dotted lines. Molykote Fill the holes at the battery solder points on both sides with Molykote FC1292 p/n Wipe the surplus Molykote off to prevent soiling of the housing at final assembly. Page 11 of 15

12 Colour Markers How to place the colour marker: Place the colour marker as long into the hole as possible. Press on the back of the marker with a finger and at the same time turn the pin around until it breaks of. Turn the pin around Pressure here with a finger How to remove the colour marker: Push out the pin a 1/3 of its length using pin tool and turn the device as if it was placed on the ear. The colour marker should then fall out. If the colour marker is not falling out, the battery door can be opened and from the inside the colour marker can be pushed out by using a colour marker remover p/n Colour marker, Red p/n Blue p/n Red p/n , 25 pcs Blue p/n , 25 pcs The pin is pushed out Push the colour marker from inside Page 12 of 15

13 Test equipment Blue dot Programming cable CS63 blue, Left p/n Battery pill must be used: Size 312 p/n Red dot Programming cable CS63 red, Right p/n Kit with programming cable, flex strip and clothes-clip: - Red p/n Blue p/n Flex strip 3 pin (10 pcs) p/n Flex strip 3 pin (25 pcs) p/n Page 13 of 15

14 Test equipment Snap-on adaptor p/n To be used with Otometrics 2cc coupler. Use XRec test tube p/n when testing Place the Xrec tube into the test fixture. Mount the snap on adaptor on the coupler and place the XRec into it. Connect the hearing instrument to the other end of the Xrec tube The test fixture must be adjusted before use. Loose the two screws. The smallest part must be positioned so that the test tube is in the center of the green circle. Fasten the screws. This adjustmest must also be done on a frequently basis to ensure optimal testing. Insert battery pill and flex strip into the HI Test fixture p/n Page 14 of 15

15 Charger spares Complete package Part no. RESOUND PULSE SUPERTUNE, EU* RESOUND PULSE SUPERTUNE, UK* RESOUND PULSE SUPERTUNE, US* RESOUND PULSE SUPERTUNE, AUS* * including all spares Spares Part no. Keyring holder Link for keyring holder Silicone block 10A Silicone block Battery slide 10A Battery slide Power supply EU Power supply UK Power supply US Power supply AUS Page 15 of 15