CableMaster 800. Gas Technology Systems. For Electrical & Plumbing Contractors

Transcription

1 CableMaster 800 For Electrical & Plumbing Contractors Depth of Drive adjustment Compact & Lightweight Design Removable 20 Pin Magazine (50 Pin Magazine Available) Electronic Fuel Injection Lithium Battery The Ramset TM CableMaster TM 800 is the most technologically advanced gas tool on the market. The new CableMaster TM 800 offers a number of innovative features allowing quicker, safer installation of a wide variety of clips for plumbing, data and electrical installations. The speed at which the CableMaster TM 800 is able to perform installations provides tremendous savings in total installed cost. Weight 3.8kg Height 309mm Length 396mm Magazine Capacity 20 (+3) pin magazine, [50 (+3) pin magazine accessory] Impact Force 82J Actuation Pressure 5kg Overdrive 4mm Intermittent Operation 2 pins per second Fuel Cell Life 750 pins (approx) Battery Charge Capacity 3,000 pins (approx) Battery Voltage 3.7V Lithium-Ion Battery Charge time 90mins (25mins for 500 fixings) Power Regulation Automatic Operating Temperature Range -5 C to 49 C Substrates Concrete, Composite Steel Decking, Solid Brick, Precast Concrete, Steel Pre-stressed Concrete, Hollow Block Wall, Reinforced Concrete, Reinforced Prefabricated Concrete Related Products Drive Pins & Fuel Cells Contractor Packs Battery & Fuel Gauge Battery Gauge Helps avoid running out of battery power. Fuel Cell Gauge Always know when to change fuel cells. Lithium Battery Fast Charge, Long Life Tool-less Depth of Drive Adjustment Power Saving Technology isolates battery when tool is not in use Compact design with 20 pin magazine Allows the tool to fit in tight spaces Easily removable fastener guide and magazine Greater tool clearance Allows the tool to fit in close to edge applications. Removable Support Leg Ensures tool is at 90 to work surface for optimum fixings Electronically controlled fuel injection Ensures consistent power in a wide temperature range. Low Maintenance. Designed to work in all conditions

2 CableMaster 800 For Electrical & Plumbing Contractors Trades & Applications Plumbing Electrical Fire & Contractor Contractor Security Permanent cable suspension to concrete and steel 4 Pipe suspension systems to concrete and steel 4 Fire and security cabling to concrete and steel 4 Temporary cable suspension to concrete and steel 4 Standard Operating Procedure Always read and understand the instruction manual before attempting to operate a Ramset Gas Technology Tool. 1. First insert the fuel cell and battery into the tool. 2. Insert the collated fasteners into the magazine. 3. The clip should then be placed on the end of the fastener guide without compressing the front end of the tool. 4. The tool should then be compressed against the work surface. (Making sure that the tool is perpendicular to the work surface). 5. Once the tool is compressed the trigger can be actuated and the fastener is driven into the substrate securing the clip in place. CableMaster 800 Order Qty CABLEMASTER800 CableMaster 800 Pulsa Gas Tool + 2 x Lithium-Ion Batteries 1 Kit includes: CableMaster 800 tool, high impact carry case, 2 x batteries, battery charger, safety glasses and instruction manual Accessories Order Qty Pin Magazine Pin Magazine Lithium-ion Battery Lithium-ion Battery Charger Magnetic Washer Adaptor CableMaster TM 800 Fastener Guide TrakFast TM 800 Fastener Guide 1 B20544L Gas Tool Degreaser and Lubricant 1 PA1613 Safety Glasses

3 CableMaster 800 Consumables Heavy Duty Pin Range for Steel and Hard Concrete Fixing Drive Pins designed for fastening to standard strength concrete, masonry and steel. Carbon Steel Corrosion Protection Zinc Electroplated (Minimum coating 5µm) Nominal Head Diameter 6.3mm Nominal Shank Diameter 2.6mm (C620 Stepped shank 2.6/2.2mm) Shear Strength 1120N/mm 2 Tensile Strength 1800N/mm 2 Hardness 52-56HR C NZ Original Pulsa 700 Length Order Qty P8HC615 HC615 Heavy Duty Steel/Concrete 15mm 500 P8HC617 HC617 Premium Hard Concrete/Steel 17mm 500 P8HC622 HC622 Premium Hard Concrete/Steel 22mm 500 P8HC627 S Premium Hard Concrete/Steel 27mm strip collation (suitable for use in 40 and 50 pin magazines) + 1 x Fuel Cell

4 CableMaster 800 Consumable Selection Guide Application Type Data Cable Strap, Plates & Fixtures Light Duty Cable Tray Flexible/Plastic Pipe Catenary Wire Electrical Conduit Cable Fixing Small Diameter Rigid Pipes Metal Pipes Metal/Nylon Straps Fire & Service Cabling ClipElec DataLec Clip CTClip EClip Threaded Rod Hanger FP FireFix Clip 4 4 CableHorn Double & Single 4 Direct Alignment Half Saddle Strap & Plate Mounting Washer 4 Catenary Wire Bracket Recommended

5 ClipElec ClipElec is an all purpose cable tie system that may be used for fixing cable, conduit and pipes for a wide variety of electrical and plumbing applications. This system is extremely versatile allowing for many different sized cables, pipes and conduit to be secured. The ClipElec all purpose cable tie system may be used with the 4.8mm supplied cable ties or with other cable ties up to a maximum width of 9mm. Polypropylene copolymer, high impact, halogen free. UV resistant Capacity Up to 9mm cable tie width. Spacing Recommendation 0.5 & 1 metre (approx) Incandescent wire test (regulation NFC ) 750 C Fire Resistance Properties passed - LCIE laboratory test results N (December 1998) Low Temperature Test No breakage at 0 C Dimensions 32 x 37mm ClipElec can be used for cable, conduit and tube work. Universal design allows cable ties up to 9mm wide. Designed with an in-built energy absorber for perfect embedment. Clips directly onto the CableMaster Pin Guide for one handed operation. Hands are a safe distance from the Pin Guide during installation. Can be used with the PulsaLift Pole to fix from the ground. Optional plug and screw installation. Hollow Concrete Block k 4 Steel 4 4 Performance Table* Load Capacity (Tension) - Concrete Pin Cable Tie Width 20MPa 32MPa P8HC617 9mm 10kg 12kg P8HC622 9mm 10kg 12kg P8C mm 2.5kg 3.7kg 1. Simply clip the ClipElec to the tool pin guide. 2. Press against the substrate, press the trigger & the clip is fixed. 3. Install the tube or conduit with cable tie. ClipElec All-purpose Cable Tie Clips P8CPGCL P8CPGCLHC617 Original Pulsa 700 CPGCL CPGCLHC617 ClipElec Contractor Pack (500 x clips, HC622 Pins, Fuel Cell, Cable Ties 200mm x 4.8mm Black) ClipElec Hard Concrete Contractor Pack (500 x clips, HC617 Pins, Fuel Cell, Cable Ties 200mm x 4.8mm Black) Order Qty 1 1 *NOTE: Test concluded when clip pulled over pin head or cable tie failed. Job-site testing may be required to determine actual achievable job-site values. Results have been achieved with a CableMaster tool set at minimum overdrive setting. Accessories failing to fix correctly should be removed and a new fixing set away from any spalled concrete. Tension loads provided are for static load situations only. Values represent a minimum factor of safety of 3:1 on the lowest test results achieved. Minimum edge distance 75mm, minimum spacing between fixings 50mm. Tension loads are per fixing, however a minimum of 3 fixings per fastening unit should be used

6 CTClip The CTClip is the all in one cable tie system. With the integral cable tie the CTClip can be used for cable, conduit and tube work. High impact, Nylon 66 Spacing Recommendation 0.5 & 1 metre (approx) Fire Resistance Properties UL94HB Fire Test CTClip can be used for cable, conduit and tube work. Maximum cable cluster or tube diameter of 63mm. Clip base raised above work surface. In-built energy absorber for optimum pin penetration. Side mount clip into pin guide. One handed installation. Fix from the ground with the PulsaLift Pole. Optional plug and screw installation. Hollow Concrete Block k 4 Steel 4 4 Performance Table* Load Capacity (Tension) - Concrete Pin 20MPa 32MPa P8HC617 7kg 9kg P8HC622 7kg 10kg 1. Side mount clip into pin guide. 2. Press against work surface. Fire tool. 3. Install the cable or conduit/tube as required. Fasten tie strap. CTClip P8CPGCT Original Pulsa 700 CPGCT Pipe / Conduit Diameter Order Qty CTClip Contractor Pack Standard (500 x clips, HC622 Pins, Fuel Cell) 16-32mm 1 *NOTE: Test concluded when clip pulled over pin head or cable tie failed. Job-site testing may be required to determine actual achievable job-site values. Results have been achieved with a CableMaster tool set at minimum overdrive setting. Accessories failing to fix correctly should be removed and a new fixing set away from any spalled concrete. Tension loads provided are for static load situations only. Values represent a minimum factor of safety of 3:1 on the lowest test results achieved. Minimum edge distance 75mm, minimum spacing between fixings 50mm. Tension loads are per fixing, however a minimum of 3 fixings per fastening unit should be used

7 DataLec Clip Multi-purpose Data & Cable Clip DataLec Clip is a Multipurpose data and cable clip for the fast installation of specialised and standard cables. Install Fibre Optic, Broadband, Cat5/6, Audio visual and other specialised cables using soft Hook & Loop Strap to correctly support and secure these cables without damage. For standard electrical and power cabling installations hard plastic cable ties or soft Hook & Loop Strap can be used to suit installation needs. This versatile and strong clip design is suitable for the installation of multiple cable bundles, multi-directional cable runs, small diameter conduits with cables and plastic/ metal pipes. Slot opening Clip spacing recommendation Dimensions (mm) Datalec Multi-purpose Data & Cable clips P8CPGDLHC617 P8CPGDLHC622 Original Pulsa 700 CPGDLHC617 CPGDLHC622 VEL1225 HDPE, High impact,halogen free 14mm wide from 0.3 to 1mtr (approx.) depending on application 33W x33d x 14H Hollow Concrete Block k 4 Steel Gently insert clip mounting tip (centre of clip) into CableMaster tool nosepiece 2. Press clip against substrate, depress CableMaster tool nosepiece and fix clip 3. Attach cable to DataLec clip with appropriate tie or strap for the application DataLec Clip Contractor Pack (Heavy duty pins 17mm) (500xclips,HC617pins,cable ties 200x4.8mm Black, Fuel cell) DataLec Clip Contractor Pack (Heavy duty pins 22mm) (500xclips,HC622pins, cable ties 200x4.8mm Black, Fuel cell) Hook and loop strap 12mm x 25metre Roll (optional extra) Order Qty One clip for data and standard cable installations Multiple cable mounting positions Wide soft Hook & Loop Strap (12mm) or hard plastic tie compatible Parallel or multi-directional cable fixing Single and cable bundle installations Non abrasive support and protection of services Suits cable in conduit and small diameter pipe applications Fix to standard and hard concrete, hollow masonry block & steel formwork Performance Table* Total tensile load capacity per DataLec TM Clip - HC617 or HC622 Pins Concrete compressive strength Width 20MPa 40MPa Cable Tie (supplied) 4.8mm 5kg 7kg Cable Tie 1 7.6mm 12kg 15kg Hook & Loop Strap 2 12mm 3kg 4kg Optional Item VEL1225 *NOTE: Testing concluded when clip pulled over pin head or strap/tie failed.job site testing may be required before use to determine actual achievable job site values. Results have been achieved using a CableMaster TM tool set at minimum overdrive setting. Accessories failing to fix correctly should be removed and a new fixing set away from any spalled concrete. Tension load capacities are for static load situations only. Values shown represent a minimum factor of safety of 3:1 against the ultimate capacity. Minimum edge distance 75mm, minimum spacing between fixings 50mm. Tension loads are per fixing, a minimum of 3 fixings should be used per fastened unit. 1. Tested with Pricemark Cable Tie, # CT-76380NAT Tested with Hook & Loop Strap - 12mm Hook & Loop Strap 60mm overlap with 50mm diam bundle

8 DataLec Clip Multi-purpose Data & Cable Clip Plastic pipe or conduit Electrical cable bundles Multiple data cable bundles Fibre optic cable in conduit Electrical cable Data cable bundles Fibre optic cable Electrical cable

9 EClip The EClip is ideal for firmly securing conduit, HDPE, and PVC pipe. Once installed, the clip is able to be rotated to allow for precise positioning of rigid and flexible tube. The design of the EClip incorporates interlocking connections to allow for multiple clips to be joined together side by side for a professional finish. Spacing Recommendation High quality polypropylene Halogen free. Fire resistant 0.5 and 1 metre (approx) The EClip is designed to clip easily onto the CableMaster Pin Guide from the side allowing one-handed operation. Hands are a safe distance from the Pin Guide during installation. Fixing is precise. After installation the EClip can be rotated around the pin to adjust alignment. The slotted design of EClip absorbs energy, preventing the pin head from splitting the clip. The hollow structure of the EClip gives flexibility for easy insertion of conduit. EClip incorporates male/female connections allowing multiple conduit installation side by side. Optional plug and screw installation. Hollow Concrete Block k 4 Steel 4 4 Performance Table Tube extraction loads at 22 C Force required to manually remove tube from the clip Clip Size 16mm 20mm 25mm Average Ultimate Load (approx) 4kg 6kg 8kg 1. Side mount the EClip onto the tool Pin Guide. 2. Fixing is quick and precise. 3. When fixed, it can be easily rotated around the pin to adjust its position. EClip Conduit Clip Original Pulsa 700 Pipe / Conduit Diameter Order Qty P8CPGEC16 CPGEC16 Contractor Pack (500 x clips, HC622 Pins, Fuel Cell) 16mm 1 P8CPGEC20 CPGEC20 Contractor Pack (500 x clips, HC622 Pins, Fuel Cell) 20mm 1 P8CPGEC25 CPGEC25 Contractor Pack (500 x clips, HC622 Pins, Fuel Cell) 25mm

10 Threaded Rod Hanger For light duty applications the Threaded Rod Hanger bracket is an ideal alternative to traditional anchors such as the DynaSet drop-in anchor. The bracket features an M8 and a M10 thread allowing for a choice of threaded rod sizes in applications such as light duty cable tray and pipe suspension. The bending movement used during application acts as a self testing mechanism for the quality of the fixing. Material Thickness Coating Carbon Steel 1.5mm Zinc Electroplated (Min. Coating 7µm) Slide-on channel for pin guide. Lateral insertion for fast, safe installation. Thick steel with reinforcing ribs for extra strength. Dual threads. Less parts, more flexibility. Optional drill and 6mm anchor installation. Electro zinc coating protects against corrosion. Hard Concrete >50MPa 4 k Concrete <50MPa 4 k Hollow Concrete Block 4 4 Steel 4 k Performance Table* TRH with HC617 Pulsa Pin Load Capacity (Tension) - Concrete 32MPa 15kg *NOTES: 1. Values represent the maximum recommended working load in tension. 2. A minimum of 4 fastenings per fastened unit must be used. 3. Results have been achieved with a CableMaster tool. 4. All visible failures must be replaced and a new fixing set away from any spalled concrete. 5. Tension loads provided are for static load situations only. 6. Job-site testing may be required to determine actual achievable job-site values. 7. Pins must be sufficiently set, such that the underside of the head of the pin is in contact with the surface. 1. Insert TRH laterally onto CableMaster pin guide to the stop position. 2. Install the TRH. The pin guide will automatically remove itself from the channel. If the guide is stuck inside the channel, gently move the tool laterally to release it. 3. Screw in the threaded rod, (two possible diameters) and bend the TRH to the vertical position using the rod or Bend the TRH by hand if you intend to use a suspended hanging system, small chain or steel wire. Threaded Rod Hanger P8CPGTRH Original Pulsa 700 CPGTRH Thread Diameter Order Qty Threaded Rod Hanger Contractor Pack (400 x hangers, HC617 Pins, Fuel Cell) TyMaster powder actuated tool installations For heavy duty applications refer to Z Bracket rod Hanger (M10) Page 52.This is a rod hanger assembly for TyMaster powder actuated tool installations. M8 - M

11 FP FireFix Clips The FP FireFix clip fire cable installation system has been developed for installing the specialised fire protection cable required for the safe operation of essentail service equipment during fire emergencies. This system consists of the FP FireFix clip installed with a Pulsa pin using the CableMaster Pulsa gas tool. Coating Stainless Steel Powder coated red Complies to AS Fixes fire rated cables ten times faster than traditional drilling methods Clip manufactured from 316 Stainless Steel powder coated Simply clips shut holding the cable(s) securely. 2 cables per clip Can be used with stainless steel cable ties to install larger cables Fast fixing to non combustible materials such as solid concrete, hollow concrete block and steel Two hour fire protection system for essential services. Utilises a plastic adaptor that fits on the CableMaster Pin Guide allowing one-handed installation. Hands are a safe distance from the Pin Guide during installation. Can be used with the PulsaLift Pole to fix from the ground. Holds one or two cables. Choice of two sizes. Simply clips shut holding the cable(s) securely. 2 cables per clip. Hollow Concrete Block 4 4 Steel 4 4 Fire Standards Compliance When independently tested in accordance with the requirements of the Fire Test Method for Supports & Fixings of AS/NZS 3013:1995 appendix B, Electrical Installations Classification of the Fire & Mechanical Performance of Wiring Systems, the FP FireFix Cable Clip (when fixed to the concrete slab via a Ramset 20mm Heavy Duty Concrete SC6 Gas Pin or HC617 Pin) was found to be able to support a static load of 1kg. Fire test reports are available upon request. 1. Fit adaptor to the CableMaster pin guide. 2. Position the FP FireFix clip 3. Push the tool against the substrate and fix the FP FireFix clip in place. NOTE: remove battery from the tool when fitting the FP FireFix adaptor. FireFix P8CPGFPO2 P8CPGFPO4 Original Pulsa 700 CPGFPO2 CPGFPO4 FireFix Clip Contractor Pack (500 x clips, HC617 Pins, 5 Fastener Guide Adaptors) FireFix Clip Contractor Pack (500 x clips, HC617 Pins, 5 Fastener Guide Adaptors) Cable Outer Diameter Order Qty 7-8.1mm mm

12 CableHorn In many applications the use of the CableHorn system can eliminate the need for cable trays to be installed. Cables may be added or removed after the CableHorn is installed. When used in conjunction with the PulsaLift pole system, CableHorns may be installed from the ground without the need for ladders or scissor lifts. Single CableHorn : 8 cables, 3 x Capacity 1.5mm 2 maximum. Double CableHorn ; 16 cables, 3 x 1.5mm 2 maximum Spacing Recommendations Between 0.60m and 1.50m High impact modified Pa66 Halogen free polypropylene. Incandescent wire test (IEC 695): Fire Resistance Properties 650 C UL94 HB (ISO 1210): 100 mm/min Low Temperature Tests No breakage at 0 C Quality Certificate TUV certificate ISO 9001 Dimensions Single CableHorn : Length 137mm. Double CableHorn : Length 228mm Fixing Base Single CableHorn : 19.5 x 38.5mm. Double CableHorn : 19.5 x 24.3mm Substrate HC622 Hard Concrete >50MPa 4 Concrete <50MPa 4 Hollow Concrete Block 4 Steel 4 Steel Decking 4 Designed for use with electrical, data and communication cables. Replaces the need for cable tray and catinary wire. Clips directly onto the CableMaster Pin Guide allowing one-handed operation. Can be used with the PulsaLift Pole to fix from the ground. Add or remove cables as required. In-built energy absorber for perfect embedment. Large fixing base for better stability. Flexibility in installation-vertical, horizontal, overhead. Optional plug and screw installation. Performance Table* Load Capacity (Tension) - Concrete Pin 20MPa 32MPa HC622 18kg 20kg 1. Simply clip the CableHorn to the tool pin 2. Press against the substrate (5kg to actuate the tool) press the trigger to fix. 3. Install the cable simply by lifting the edge of the CableHorn. CableHorn Fixing P8CPGCH140 P8CPGCH Original Pulsa 700 CPGCH140 CPGCH Fixing Capacity Order Qty CableHorn Contractor Pack (200 x fixings, HC622 Pins, Fuel Cell) CableHorn Contractor Pack (125 x fixings, SC620 Pins, Fuel Cell) 8 Cables (3 x 1.5mm 2 ) 1 16 Cables (3 x 1.5mm 2 ) 1 *NOTE: Test concluded when clip pulled over pin head or pin failed. Job-site testing may be required to determine actual achievable job-site values. Results have been achieved with a CableMaster tool set at minimum overdrive setting. Accessories failing to fix correctly should be removed and a new fixing set away from any spalled concrete. Tension loads provided are for static load situations only. Values represent a minimum factor of safety of 3:1 on the lowest test results achieved. Minimum edge distance 75mm, minimum spacing between fixings 50mm. Tension loads are per fixing, however a minimum of 3 fixings per fastening unit should be used

13 Conduit Half Saddle Conduit Half Saddles are suitable for fixing conduit and metal pipes. Standard Half Saddles may be used with the CableMaster tool in conjunction with a Saddle Adaptor. Direct Alignment Saddles make the job even faster by clipping directly onto the fastener guide. Material Thickness Coating Hollow Concrete Block 4 4 Steel 4 4 Bondeck Gently place saddle assembly into end of pin guide. 2. Place saddle over conduit/tube. 3. Depress nose piece against work surface, fire tool. Carbon Steel 1.6mm Zinc Electroplated (Min. Coating 7µm) FAST accurate fixing of conduits and tubes to concrete,hollow block, & steel. Fits directly to nose piece of CableMaster Pulsa gas tool Precise hole alignment. Optimum pin penetration and strength. Neat and flush finish. One hand installation. Optional drill and 5mm anchor installation. Site test recommended for use in critical applications. Direct Alignment Conduit Half Saddles Direct Alignment Conduit Half Saddles P8CPGDAS20 P8CPGDAS25 Original Pulsa 700 CPGDAS20 CPGDAS25 Pipe / Conduit Diameter Order Qty Direct Alignment Saddle Contractor Pack (400 x saddles, HC617 Pins, Fuel Cell) Direct Alignment Saddle Contractor Pack (400 x saddles, HC617 Pins, Fuel Cell) 20mm 1 25mm

14 Strap/Plate Washer The Strap and Plate Washer may be used in a wide variety of applications where thin materials or fixtures with existing holes need to be quickly fastened. Common applications where the Strap and Plate washer are used include securing thin metal, nylon and Hook & Loop straps for ducting, cable bunches and other fixtures. Brackets with existing pre-drilled holes for traditional mechanical fasteners can be secured with the use of strap and plate washers. Steel type Steel Thickness Nominal Diameter CA2S-E. 1.6mm providing a high resistance to deformation. 16mm FAST One-Step Fixing of metal, nylon and Hook & Loop straps for ductwork, cable bunches and fixture installations. Suitable to span wide mounting holes in cable suspension brackets or switchboxes up to 8mm diam. To reinforce mounting holes in brackets and prevent fixture pullover. Precise hole alignment. Use with pre-drilled or solid straps and plates. Suitable for use with CableMaster Pulsa collated pins. Choose the pin length to suit the application. SC6 or HC6 pins recommended. One handed fixing to concrete, hollow block and steel. Hollow Concrete Block 4 4 Steel Gently place washer assembly into end of nose piece. 2. Place assembly tip in position. 3. Depress nose piece against work surface, fire tool. Strap and Plate Washer Order Qty SPMW Strap and Plate Washer

15 Catenary Wire Bracket Reinforced steel angle bracket, with closed eye for catenary wire and cable installations when fixing to concrete, concrete block and steel. Suitable for light to medium duty, close to ceiling applications. Steel type Steel Thickness Nominal Fixing Hole Diameter CA2S-E. 2mm providing a high resistance to deformation. 7.5mm For catenary wire, cable, and hanger rod installations when fixing to concrete, hollow block and steel. Improved clampdown to work surface with dimpled baseplate. Optimum pin penetration with cushioned base. Strengthening ribs reduce bracket twist and deformation. Rounded edges to prevent cable damage. Three methods of installation. - Fast fixing with CableMaster Pulsa gas tool. - TyMaster tool installation (See page 52). - Traditional drill and anchor method. Suits light to medium duty fixing applications. (see performance table) Fix from the ground with pole tool. Eye size - 7mm. Hollow Concrete Block 4 4 Steel 4 k Performance Table* Product Cat Brkt Pulsa assembly, HC617 Pin Load Capacity (Tension) - Concrete 32MPa 14kg 1. Place bracket assembly into the pin guide. 2. Depress pin guide against work surface, fix bracket into position. 3. Attach cables and wires as required. Catenary Wire Bracket Assembly Original Pulsa 700 Catenary Wire Bracket Contractor Pack (400 x brackets, HC617 Pins, Fuel Cell, P8CPGCWB CPGCWB 200mm x 4.8mm Black) *Notes: 1. Values represent the maximum recommended working load in tension. 2. A minimum of 5 fastenings per fastened unit must be used. 3. Results have been achieved with a CableMaster tool. 4. All visible failures must be replaced and a new fixing set away from any spalled concrete. 5. Tension loads provided are for static load situations only. 6. Job-site testing may be required to determine actual achievable job-site values 7. Minimum edge distance 75mm. Minimum spacing between fixings 50mm. Order Qty