EP30006 CANADA MASSAGE LOUNGER SPECIFICATIONS EP30006 ORDER NO.HPD0709C21C1

Transcription

1 MASSAGE LOUNGER EP30006 CANADA SPECIFICATIONS 2007 Matsushita Electric Works, Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law

2 CONTENTS Page 1 COMPONENTS IDENTIFICATION 3 2 TURNING ON THE POWER 7 3 REQUIRED TOOLS 8 4 ADJUSTMENT OF PRESSURE SENSOR 9 5 OPERATIONS OF ELECTROMAGNETIC VALVES AND AIR BAGS 10 6 DISPLAY METHOD OF MASSAGE BLOCK TOTAL USE TIME 11 7 DISPLAY METHOD OF EACH OPERATION USE TIME 12 8 METHOD OF PACKAGING POSITION SET-UP 12 9 METHOD OF MASSAGE MECHANISM BLOCK INSTALLATION MODE SET-UP (MANUAL SET-UP) DISASSEMBLY ACTUAL WIRING DIAGRAM PHENOMENA CAUSED BY THE SENSOR MALFUNCTION OR LOCK PROTECTION OPERATION CHECKING GREASE EXPLODED VIEW REPLACEMENT PARTS LIST

3 1. COMPONENTS IDENTIFICATION 1.1 MASSAGE LOUNGER - 3 -

4 - 4 -

5 1.2 CONTROLLER - 5 -

6 - 6 -

7 2. TURNING ON THE POWER 1. Plug the power plug into the power socket. 2. Turn the lock switch to the open position. 3. Turn on the power switch on the back of the unit. When the operating lock switch is pointing toward lock, the power switch cannot be moved to the on position. After each use. Be sure to turn the power switch to off. To prevent children from using this unit, lock the power switch by moving the operating lock switch to the lock position. As a further caution, unplug the power cord from the power socket after each use. Timer When the on/off button is pushed, a timer begins to prevent overuse. After approximately 15 minutes, time expires and the massage wheel goes into storage position

8 3. REQUIRED TOOLS - 8 -

9 4. ADJUSTMENT OF PRESSURE SENSOR The adjustment of the Pressure sensor is necessary every time after the Main PCB or Massage mechanism block are replaced or repaired disassembled & reassembled. First, keep the Massage mechanism block unloaded without pressure and move it upward halfway. - If the Massage mechanism block is at the highest or lowest position, you cannot arrange the pressure sensor correctly because the fabric becomes tense with pressure. 1. Insert the Power plug into the power source and turn on the switch of the Power source switch block. 2. While pushing the buttons of Ⅰ and Ⅲ, continue to push the On/off button for more than approximately three seconds. Then, the buttons of Ⅰ, Ⅲ, and USER A light. 3. In ten seconds after the buttons of Ⅰ, Ⅲ, and USER A light, push the buttons as follows: 1SELF PROGRAM 2 LEG/FOOT 3AUTO WIDTH 4START 4. Push the button of START again, then the adjustment of Pressure sensor finishes. 5. Push the button of Stop

10 5. OPERATIONS OF ELECTROMAGNETIC VALVES AND AIR BAGS Air massage operates with one Pump unit, nine 3-way electromagnetic valves, an Switch electromagnetic valve. 1. Air massage operates with the Pump and the Electromagnetic valve. 2. The Pump and all the Electromagnetic valves are OFF when the operation stops. 3. Air control stops when the Reclining lift motor and the Ottoman lift motor operate.(electromagnetic valves are OFF in ventilation.) 4. The Pump stops when in the On/off operation, or Electric reclining lift unit or Electric Ottoman lift unit operate in the standby mode.(pressure level is maintained.) Electricity is OFF in five seconds after the Packaging mode, or the operation stop after the stop mode (Packaging mode), or Electric reclining lift or Electric Ottoman lift are OFF in the standby mode. *However, the Lift motors operate controlling the air when in stretching of legs and ankles

11 6. DISPLAY METHOD OF MASSAGE BLOCK TOTAL USE TIME 1. Insert the Power plug into the power source and turn on the switch of the Power source switch block. 2. While pushing the buttons of Ⅲ and Ⅳ, continue to push the On/off button for more than approximately three seconds. Then, the button of USER D lights. 3. In ten seconds after the button of USER D lights, push the buttons as follows:1self PROGRAM 2LEG/FOOT 3 LOWER 4START 4. Push the button of Stop. HOW TO READ THE DISPLAY OF THE ACCUMULATIVE OPERATION TIME * Count the numbers of display as arrows

12 7. DISPLAY METHOD OF EACH OPERATION USE TIME While in the display method of Massage block total use time, push the button of START as many as you like based on what accumulative operation use time you want to know. *Icons are same of those of previous page. *Push the button of Stop after checking the display. 8. METHOD OF PACKAGING POSITION SET-UP 1. Insert the Power plug to the power source and turn on the switch ON on the Power source switch box. 2. While pushing the buttons of Ⅰand Ⅱ at the same time, push the button of On/off for approximately three seconds. (Buttons of Ⅰ,Ⅱ, and USER C light.) 3. Push the button of Reclining up to start the Packing position set-up. (Ottoman and Reclining lean down, and Massage mechanism block moves to the packaging position.) (When you want to stop the operation, push the button of Stop.)

13 9. METHOD OF MASSAGE MECHANISM BLOCK INSTALLATION MODE SET-UP (MANUAL SET-UP) It is necessary to adjust the Massage mechanism block to Manual mode when installing or removing the Massage mechanism block or adjusting the Up/down position as follows: 1. Insert the Power plug into the power source and turn on the switch of the Power source switch block. 2. While pushing the buttons of Ⅱ and Ⅳ, continue to push the On/off button for more than approximately three seconds. Then, the buttons of Ⅱ, Ⅳ, and USER B light. 3. In ten seconds after the buttons of Ⅱ, Ⅳ, and USER B light, push the buttons as follows:1self PROGRAM 2 REGIONAL ROLL 3START 4. Move the Massage mechanism block pushing the buttons of POSITION and BACK INTENSITY. 5. Push the button of Stop after checking

14 10. DISASSEMBLY Removing the Rear cover 1. Remove two screws and two push-turn rivets, and pull off the Rear cover top. 2. Remove two brushclips from the Rear cover bottom, and pull off the Rear cover bottom Removing the Massage mechanism block Move the Massage mechanism block to the bottom pushing the high/low adjustment button. 1. Unscrew four screws on the PCB cover, and remove the PCB cover

15 2. Unscrew a screw on the Ground wire and disconnect two Connectors. 3. Remove the Connecting cord for power source from the Massage block cover clip. 4. Unscrew four screws each on both sides and remove the Rail piece sets. Caution The Massage mechanism block may fall down, therefore hold it by your hand. Be careful of the directions of the Rail piece sets when installing

16 Caution when handling the Massage mechanism block Be sure to handle the Massage mechanism block carefully so that the PCB of the Pressure sensor is not pushed to the desk or given extra pressure when putting the Massage mechanism block, which could lead to the cracks of the PCB. This may eventually cause the malfunction such as The body pressure levels on the Controller does not increase. It does not scan. or The operation is not stable. etc Removing the Controller stand and the Armrest Removing the Controller 1. Pull off the parts A with a slotted screwdriver. 2. Take off the Controller from the Controller stand, and unscrew three hexagonal screws and remove the Controller stand Removing the Armrest 1. Unscrew two screws from inside and outside the Armrest

17 2. Remove the Hose connected to the Armrest. 3. Lift the Armrest and remove it. 4. Execute the same procedure on the opposite side Removing the Covers 1. Proceed the all the procedures of Removing the Controller stand and the Armrest. 2. Unscrew a Push-turn rivet on the Under cover. 3. Unscrew seven screws on the B

18 4. Remove the B and pull out the Hose connected to the B. 5. Unscrew two screws on the C. 6. Lift the C to remove it. 7. Unscrew ten Push-turn rivets, and remove the Lift protection sheet

19 8. Unscrew nine Push-turn rivets on the Under cover right/left. 9. Remove the Under cover right/left. *Remove the Power source switch box before removing the Under cover left. Caution when installing When installing the Under covers, be sure to check whether the Air hoses are hooked or bent and also the Ottoman block moves smoothly Removing the Under box / Under box cover 1. Proceed all the procedures of Removing the Covers.[ 2. Put the Ottoman block on the 30-cm box, unscrew three screws on the Under box top/left, and lift the Under box top/left. 3. Unscrew a screw on the Under box top/right, and slide the Under box top/right to left and unhook four hooks

20 4. Unscrew two screws and remove the D. 5. Remove the Rod holder from the Under cover top/right. 6. Remove seven Hoses from the Under box top/left, and remove the Under box top/left. *When installing Hoses, be careful of the arrangement of the Hoses. 7. Unscrew three screws and pull off the Under box from the front. Caution Be careful of the position of the Ottoman hoses and check if the four Hooks are hooked when the Under box right/top is installed

21 10.6. Removing the Lift unit Removing the Ottoman lift unit 1. Proceed all the all the procedures of Removing the Massage mechanism block. * The work will be easy and secure if the Massage mechanism block is completely moved down. 2. Proceed all the procedures of Removing the Covers. 3. Proceed the procedures of 1-4 of the Removing the Under box, and disconnect the white Connectors of the Ottoman lift unit (CN107, CN201). 4. Remove the Ottoman lift pin long, Snap pin, and remove the Ottoman lift unit. *It would be easy to remove the Ottoman lift unit if you move down the Massage mechanism block

22 Removing the Reclining lift unit 1. Proceed all the all the procedures of Removing the Massage mechanism block. * The work will be easy and secure if the Massage mechanism block is completely moved down. 2. Proceed all the procedures of Removing the Covers. 3. Proceed the procedures of 1-4 of the Removing the Under box, and disconnect the blue Connectors of the Ottoman lift unit (CN108, CN200). 4. Remove the Ottoman lift pin long, Snap pin, and remove the Lift unit. *It would be easy to remove the Ottoman lift unit if you move down the Massage mechanism block

23 10.7. Removing the Seat 1. Proceed all the procedures of Removing the Rear cover, Removing the Armrest, and Removing the Covers. 2. Unscrew three Screw. 3. Unhook the Hooks at both sides. 4. Pull off the Seat air hose. 5. Cut the Insulation tie, and unzip the zippers between the Seat and the Ottoman

24 6. Unscrew two Pushturn rivets eacht at both sides. Caution in installing When installing the Pushturn rivets or Hooks, pull the Ottoman lever and make the Ottoman extended fully so that Air hoses are not hooked. 7. Unzip the Zippers on the reverse side. Caution in installing Be careful of the directions of the Hose clamps when connecting the Hoses to the Seat side air bags Removing the Foot cover 1. Proceed all the procedures of Removing the Covers. 2. Remove the Screw covers three each at both sides with a slotted screwdriver

25 3. Unscrew three screws each at both sides and remove the foot covers at both sides. 4. Pull off the Pin and the Snap pin, and remove G (both sides) Removing the Ottoman Removing the Ottoman 1. Proceed all the procedures of Removing the Covers. 2. Proceed the 5. of Removing the Seat, and unzip the Zippers between the Seat and the Ottoman, and remove Pushturn rivets. 3. Proceed the 4. of Removing the Under box. 4. First, pull out the Wire fixing parts aside and take off the swell parts

26 5. Pull out five Hoses and remove them from the Rod holder, which passes Hoses to the Under pipe. The work will be easy if you do before the Ottoman is removed. Caution when installing Be sure to check if the swell parts of the Rod holder faces the Seat. (Otherwise, the swell parts and the Seat become scrubbed and causes tearing in high possibility.)

27 6. Remove the Hinge pin B, Flat washer, U nut, then you can remove the Ottoman Disassembling the Ottoman 1. Proceed all the procedures of Removing the Ottoman. 2. Remove the Spring. If it is difficult, push down the middle of the Spring and pull up the tips of the Spring with pliers. 3. Unscrew three screws each at both sides, which fixes H, and lift I to remove H

28 4. Unscrew four screws, and remove J. Be careful not to lose the Washer, which is installed at one side. 5. Unzip two zippers. 6. Pull out the Hose from the hole of the cloth, remove a Spring and a Hose, and you can remove the Air Ottoman cloth

29 7. Unscrew five screws, and remove K. 8. Pull off the Snap pin, and pull off the Pins at both sides, and the upper and lower Ottoman break apart. 9. Remove Air bags as the figure

30 Caution in installing Arrange Hoses as figures and bundle them. Caution in installing Be careful of the directions of the Sole shiatsu sheets

31 Removing the Headrest, Back cushion, and Massage wheel cover Removing the Headrest 1. Remove the Headrest Removing the Back cushion 1. Unzip the zippers, and remove the Back cushion Removing the Massage wheel cover * You can work even with the Massage mechanism block installed. 1. Proceed the procedure of Removing the Rear cover. 2. Pull off the Air hose of the outside shoulders connected to the Sub PCB. 3. Cut three Insulated ties fixed on the Seat side. 4. Unscrew eight screws on the Massage wheel cover, and remove the Massage wheel cover. * Move the Massage mechanism block up and down, and unscrew screws

32 Removing the Outside shoulder right/left 1. Proceed the procedures of Removing the Massage wheel cover. 2. Cut the Insulated ties at both sides. 3. Pull out the Upper parts of Air hose. 4. Unscrew five screws, and pull off the Outside shoulder unit forward to remove it. Caution in installing When installing the Air hoses, be sure to put the Air hoses into the ditches as figure. If the Air hoses are installed not firmly, it may push the Hose and cause the accidents that Air bags do not bloat

33 Removing the Rear frame 1. Proceed the procedures of Removing the Covers, and Removing the Massage wheel cover. 2. Pull off three Pins. Be careful of the Rear frame, which may fall down after Pins are taken off

34 MASSAGER UP/DOWN SENSOR GEAR ADJUSTMENT METHOD When the massager is removed from the chair, the position of the up/down sensor gear changes, resulting in a change of the up/down stop position. When installing the massager on the back frame, be sure to adjust the position with the up/down detection gear. Up/down sensor gear position adjustment procedure 1. Before mounting, the massager on the back frame must be moved down to the lowest position by setting the controller manual operation MASSAGE HEAD ADJUSTMENT button to DOWN. 2. Install Rail pieces (left/right) and screw them with each four screws. 3. Make sure that the massager has been mounted horizontally by moving the massager. *Unless the massager has been mounted horizontally, an abnormal sound or problem may occur. 4. Move it up to the highest position (until the massager stops) by setting the controller manual operation MASSAGE HEAD ADJUSTMENT button to up. 5. Peeping into the square hole of the back frame, check the position of the massager to adjust. *One thread of the up/down sensor gear gives a stroke change of 4mm. When the massager has been raised excessively : Turn the up/down sensor gear counterclockwise to adjust. When the massager has been lowered excessively : Turn the up/down sensor gear clockwise to adjust. * When adjusting the up/down position, hold the Gear and adjust it. ( Do not touch the sensor board.) 6. While adjusting the distance between the square hole and Guide roller assy. to 10mm, check by using the up/down adjustment button found on the manual operation panel of the controller. 7. Using the manual operation of the controller, conduct the rolling operation

35 TIPS IN INSTALLING THE CONNECTING CORD FOR POWER SOURCE Move the Massage mechanism block to the highest position. * After installing each Connecting wires, be sure to move the Massage mechanism block up and down pushing the buttons on the Controller so as to check whether each Connecting cords do not touch Belts or the Rear cover fixing plate or are not hooked on the Up/down pinions on both sides. And check also if each Connecting cords are not extremely tense when the Massage mechanism block is at the highest position. Caution When installing the Rear cover, move the Massage mechanism block to the highest position first so as to prevent the hooking of each Connecting cords. And wind the cord around the wire. If you wind the wire around the cord, the wire becomes bent

36 ALLOCATION OF EACH LEAD WIRE OF MASSAGE MECHANISM Allocate the Main PCB, each Motors, each Sensors, and the other parts and bind the Insulated ties as the figure

37 DISASSEMBLY AND ASSEMBLY OF MASSAGE MECHANISM BLOCK DISASSEMBLY OF AIR UNIT 1. Remove the Massage mechanism block from the Rear frame. 2. Unscrew four Screws, and remove the PCB cover. 3. Unscrew two Screws, two Brushclips, and four Install rubbers on the Air unit. 4. Unscrew seven Screws. 5. Cut four Insulated ties. 6. Unscrew four Screws and remove two Hoses, then you can remove the internal parts. Caution in assembly Be sure not to make each Lead wires hooked in ribs when in assembly

38 Removing the Up/Down sensor 1. Disconnect the Connector. 2. Cut two Insulated ties. 3. Unscrew two Screws, which screw the Up/down gear box B and the Up/down sensor install plate, and remove the Up/down sensor. Caution in assembly Be sure to make the foot of the Sensor install plate fit into the ditch of the Up/down gear box B when installing the Up/down sensor

39 Removing the Intensity sensor 1. Disconnect the Connectors on the Main PCB. 2. Cut two Insulated ties. 3. Unscrew one Screw. Caution in assembly - Put the swell parts of the Massage mechanism block frame to the hollow parts of the Intensity sensor. (Otherwise, it may lead to the overrun in the direction of stronger.) - When fixing the Lead wires with Insulated ties, move the Massage mechanism block in the directions of strong-weak so as to check whether the Lead wires are pulled or hooked

40 Removing the Width sensor 1. Disconnect all the Connectors on the Main PCB. 2. Cut the Insulated ties bundling the Lead wires. 3. Unscrew four Screws on the Main PCB install plate. 4. Cut three Insulated ties on the Width sensor install plate. 5. Unscrew two Screws on the Width sensor install plate. Be sure to allocate Hoses as the figure. 6. Remove one Snap pin installing the Sensor plate. Caution in assembly - When fixing the Lead wires with Insulated ties, move the Massage mechanism block in the directions of strong-weak so as to check whether the Lead wires are pulled or hooked

41 Removing the Width motor 1. Disconnect the Connector (CN501) on the Main PCB. 2. Cut the Insulated ties bundling Lead wires. 3. Remove the Width belt. 4. Unscrew four Screws on the Width motor Removing the Pinching air bag 1. Remove the Massage mechanism block from the Rear frame. 2. Remove the PCB install plate. 3. Remove the Pin. 4. Remove the Rivet. 5. Remove two Hex screws, then you can remove the Pinching air bag. Caution in installing Be careful of the directions of install of the Hose clamp and the Snap pin

42 Removing the Float air bag 1. Remove the Massage mechanism block from the Rear frame. 2. Remove the PCB install plate. 3. Remove the Pin. 4. Remove the Rivet. 5. Unscrew the Screw. 6. Move the Float air bag in the direction of arrows, and remove it from the hollow parts of the Float air bag. 7. Move the Eccentric link plate in the direction of the arrows and unhook it. *Until the hook is released, move the Air bag in the direction of the arrow Unscrew two Screws on the Float air bag

43 Removing the Up/down gear block *You cannot replace the Up/down shaft or Up/down motor unless you disassemble the Up/down gear block. *Proceed the procedures of 1-4 of Removing the Width sensor. 1. Remove the Massage mechanism block from the Rear frame. 2. Unscrew ten Screws on the Massage mechanism block frame, Up/down driving block install plate, and Intensity driving block install plate. 3. Unscrew two Screws on the Up/down sensor install plate. 4. Unscrew three Screws on the Up/down gear box and the Up/down driving block install plate. 5. Unscrew four Screws on the Up/down gear box A/B. 6. Unscrew two Screws on the Up/down gear box and the Up/down motor. (One of them is the Grounding terminal.) Removing the Up/down shaft (Up/down shaft bolt) *Work with the Massage mechanism block unloaded. 1. Remove the Up/down shaft bolt on the Pinion B/C with the 13mm box driver and the Phillips screwdriver. Caution in assembly - The Up/down shaft bolt may be broken if tightened excessively. To tighten it, use the Torque wrench with the torque, 35 to 45kgfcm ( Ncm)

44 11. ACTUAL WIRING DIAGRAM HOSE ALLOCATION

45 11.2. WIRING DIAGRAM OF MAIN PCB AND SUB PCB

46 11.3. HOSE ALLOCATION OF AIR OTTOMAN

47 12. PHENOMENA CAUSED BY THE SENSOR MALFUNCTION OR LOCK PROTECTION OPERATION Phenomena caused by the sensor malfunction

48 12.2. Phenomena caused by the Reclining lift (Ottoman lift) sensor Phenomena in the Lock protection movement (abnormal detection by the overloading) by the Reclining lift motor (Ottoman lift motor)

49 13. CHECKING

50 - 50 -

51 - 51 -

52 - 52 -

53 - 53 -

54 13.2. CHECKING THE AIR BAGS 1. You can check the air leakage by this inspection. Remove the Under covers. Connect the Air inspection tool (WEP000S8908) and the Special hose (WEP000K8917) to each Hoses from the Under box. *Connect to the Hose that you inspect. 2. Turn the power switch on and push the On/off button on the Controller. Open the left cover and check each operations of LEG/FOOT, SEAT, HAND/ARM, and SHOULDER. 3. Push the button of Air intensity on the Controller and check the 5-level pressures. If the values are within the standard, the Air bags, Pump unit, and Air hoses are normal. If not, the following malfunctions are assumed: 1.Bent hoses between Air bags and Pump unit 2.Malfunction of each Electromagnetic valves 3.Malfunction of Pump unit 4.Air bag rupture

55 *Requested pressure values are as follows:

56 13.3. CHECKING THE ELECTROMAGNETIC VALVES 1. You can check the Electromagnetic valves.proceed all the procedures of Removing Covers, and Removing Under box and Under box cover. 2. Remove the Hose, which issues air, and check if the operation voltage of the Electromagnetic valve is as follows: The output voltage of the Connector White (CN203) on the Sub PCB is approx. DC90V. 3. The resistance values between both terminals of each Electromagnetic valves should be as follows: 3 way electromagnetic valve small: 60-70kΩ/ DC12V Electromagnetic valve unit: kΩ/AC100V Open electromagnetic valve: kΩ/AC100V 3 way 2 row electromagnetic valve unit: kΩ/AC100V

57 14. GREASE

58 - 58 -

59 - 59 -

60 15. EXPLODED VIEW

61 - 61 -

62 - 62 -

63 - 63 -

64 - 64 -

65 - 65 -

66 16. REPLACEMENT PARTS LIST Ref.No. Part No. Part Name & Description Remarks Per Unit 1 WEP3530L0087 REAR FRAME 1 2 WEP3530L0007 SIDE HINGE FITTING RIGHT 1 3 WEP3530L0017 SIDE HINGE FITTING LEFT 1 4 WEP3530L6717 SCREW 8 5 WEP3200L0887 RESIN BUSHING 12 6 WEP3530L0267 REAR COVER FIXING PLATE 1 7 WEP2000L9567 SCREW 55 8 WEP2005L0687 CORD WIRE 1 9 WEP3530L0767 RAIL PIECE RIGHT 1 10 WEP3530L0777 RAIL PIECE LEFT 1 11 WEP573L6627 SCREW WEP2110L0907 HINGE PIN A WEP3530L1538 RECLINING LIFT UNIT 1 14 WEP3530L1528 OTTOMAN LIFT UNIT 1 15 WEP3010L0417 OTTOMAN LIFT PIN LONG 4 16 WEP3530K1568 OTTOMAN SLIDE LEVER 1 17 WEP3530K0097 UNDER PIPE 1 18 WEP3510L0497 S SPRING 1 19 WEP3530L0277 STAND INSTALL FITTING RIGHT 1 20 WEP3530L0287 STAND INSTALL FITTING LEFT 1 21 WEP3530L9317 SCREW 2 22 WEP2000L9577 SCREW WEP3530K3907 CASTOR 2 24 WEP3530L0917 HINGE PIN A MO 2 25 WEP596N0357 SNAP PIN 8 26 WEP578K3377 BOTTOM PLATE 4 27 WEP3510S9027 SCREW WEP2200L ROW JOINT 2 29 WEP2110L ROW JOINT 1 30 WEP3530K3187 SCREW COVER 6 31 WEP3530K3138 LEG COVER RIGHT 1 32 WEP3530K3158 LEG COVER LEFT 1 33 WEP780L0447 MASSAGE BLOCK COVER CLIP 4 34 WEP3510L0317 HOSE CLIP 1 35 WEP3200L0277 HOSE CLIP 1 36 WEP005W8517 INSULATED TIE 3 37 WEP005W8527 INSULATED TIE LARGE 1 38 WEP3530K2018 POWER SOURCE SWITCH BLOCK 1 39 WEP3530K3098 POWER SOURCE COVER 1 40 WEP3510K3287 LOCK BUTTON 1 41 WEP3530K3258 SWITCH 1 42 WEP3510L2327 MICRO SWITCH SHEET 1 43 WEP3010L2027 MICRO SWITCH 1 44 WEP3510S9087 SCREW 1 45 WEP2400L9067 SCREW 2 46 EP3203K2058W POWER CORD 1 47 WEP3530H7868 LOCK KEY 1 48 WEP3010S9087 SCREW 1 49 WEP3530K3758 OTTOMAN COVER K

67 Ref.No. Part No. Part Name & Description Remarks Per Unit 49 WEP3530T3758 OTTOMAN COVER T 1 50 WEP3530L0627 SOLE SHIATSU SHEET RIGHT 1 51 WEP3530L0637 SOLE SHIATSU SHEET LEFT 1 52 WEP3200L0467 ANCHOR CLIP WEP3530L0687 HOSE 2 ROW LEG BLACK 1 54 WEP3530L0887 HOSE 1 ROW LEG 1 55 WEP3530L0697 HOSE 2 ROW LEG BROWN 1 56 WEP3530L0677 CONNECTION HOSE 1 57 WEP3530L0827 LEG LARGE AIR BAG RIGHT 1 58 WEP3530L0837 LEG LARGE AIR BAG LEFT 1 59 WEP1270L0847 LEG SMALL BACK AIR BAG RIGHT 1 60 WEP1270L0927 LEG SMALL BACK AIR BAG LEFT 1 61 WEP3530L0947 LEG SMALL MIDDLE AIR BAR RIGHT 1 62 WEP3530L0967 LEG SMALL MIDDLE AIR BAG LEFT 1 63 WEP1270L0987 LEG SMALL FRONT AIR BAG RIGHT 1 64 WEP1270L0997 LEG SMALL FRONT AIR BAG LEFT 1 65 WEP3530L0867 FOOT SOLE AIR BAG RIGHT 1 66 WEP3530L0997 FOOT SOLE AIR BAG LEFT 1 67 WEP3530L0318 LEG UNDER URETHANE 2 68 WEP3530L0557 LEG COVER 1 69 WEP3530L0347 LEG PIPE 1 70 WEP3530L0117 PIPE COVER RIGHT 1 71 WEP3530L0137 PIPE COVER LEFT 1 72 WEP3530L0397 OTTOMAN RACK 1 73 WEP3530L9677 SCREW 8 74 WEP3530L0147 SLIDE GUIDE 2 75 WEP3530L1407 LINEAR SLIDE 2 76 WEP3200L1498 SLIDE PLATE 2 77 WEP3530L1507 SLIDE STOPPER 2 78 WEP3530L0207 CONNECTION PLATE REINFORCE PLATE 2 79 WEP3530L6327 SCREW 4 80 WEP3530L9667 SCREW 4 81 WEP3530L0177 SLIDE SPRING 2 82 WEP3530L0187 MULTI ACTION SPRING 1 83 WEP3530L0567 FOOT COVER 1 84 WEP3530L0307 FOOT PIPE 1 85 WEP3200L0937 HINGE PIN MINI D 2 86 WEP596N0357 SNAP PIN 2 87 WEP3530L0237 FOOT UNDER COVER 1 88 WEP3530L1567 OTTOMAN LEVER WIRE 1 89 WEP3510L0407 RATCHET SPRING 1 90 WEP3510L0457 WIRE STOPPER BLOCK 1 91 WEP3530L0247 SLIDER CONNECTION PLATE 1 92 WEP3530L0927 HINGE PIN B 2 93 WEP3530L6937 V LOCK NUT 2 94 WEP3530L0257 SLIDE BASE 1 95 WEP3530L0227 PIPE END 2 96 WEP005W8507 INSULATED TIE 1 97 WEP3530L3147 CORD INSTALL FITTING PLATE

68 Ref.No. Part No. Part Name & Description Remarks Per Unit 98 WEP3530L3137 CORD INSTALL FITTING 1 99 WEP3530L0217 EDGE PROTECTION TUBE WEP2200L9697 SCREW WEP3200L0267 UNDER BOX TOP RIGHT WEP3210L0257 UNDER BOX TOP LEFT WEP3530K7187 CONTROLLER STAND WEP3515K7197 CONTROLLER INSTALL HOLDER WEP3530L7937 INSTALL SCREW WEP3530L2907 CONNECTING CORD FOR ELECTROMAGNETIC VALVE FOR EP WEP3530L2897 CONNECTING CORD FOR 3 WAY ELECTROMAGNETIC VALVE WEP3530L WAY ELECTROMAGNETIC VALVE A WEP3530L2917 CONNECTING CORD FOR 3 WAY ELECTROMAGNETIC VALVE WEP3530L WAY ELECTROMAGNETIC VALVE WEP3530L WAY 2 ROW ELECTROMAGNETIC VALVE WEP3530L2457 ELECTROMAGNETIC VALVE WEP3530L2178 SUB PCB FOR EP WEP2000L6017 SCREW WEP3530L2258 POWER SOURCE TRANSFORMER WEP2000L6967 PCB BUSHING C WEP2110L0517 BOARD SUPPORT WEP3530L3517 UNDER BOX BOTTOM WEP3530L3757 EDGE GUARD WEP3530L3157 GROUNDING PLATE WEP005W8537 INSULATED TIE WEP3530L4477 PUMP WEP3510L0287 SURGE TANK WEP3210L0357 HOSE CLAMP WEP3530L0787 HOSE PUMP WEP3530L0707 HOSE 3 WAY WEP3530L0587 HOSE 3 WAY LARGE WEP3530L0647 HOSE 3 WAY WEP3510L0097 Y JOINT WEP3530L0657 HOSE 2 WAY WEP2110L0137 L JOINT WEP3530L0817 HOSE 2 ROW UNDER B WEP3530L0537 HOSE 2 ROW UNDER A WEP3530L0797 HOSE UNDER WEP3530L0807 HOSE UNDER WEP3530L0957 HOSE RIGHT ARM WEP3530L0747 L HOSE CUT WEP3530L0667 L HOSE WEP3500L WAY JOINT WEP3530L0617 HOSE LEFT ARM WEP3530L0987 HOSE LEFT AMR WEP3530L0577 HOSE BACKS WEP3530K3678 HEAD REST K WEP3530T3678 HEAD REST T WEP3530K3618 BACK CUSHION K WEP3530T3618 BACK CUSHION T

69 Ref.No. Part No. Part Name & Description Remarks Per Unit 146 WEP3530K3148 MASSAGE WHEEL COVER K WEP3530T3148 MASSAGE WHEEL COVER T WEP755L9687 SCREW WEP3530L0757 SHOULDER OUTSIDE HOSE WEP3530K3108 SHOULDER OUTISDE RIGHT K WEP3530T3108 SHOULDER OUTSIDE RIGHT T WEP3530K3118 SHOULDER OUTSIDE LEFT K WEP3530T3118 SHOULDER OUTSIDE LEFT T WEP3530K3127 SHOULDER OUTISDE SHIATSU SHEET WEP3530K3188 REAR COVER TOP WEP3530K3168 REAR COVER BOTTOM WEP3510K0997 SCREWRIVET WEP2110K0447 PUSHTURN RIVET WEP3530K3688 SEAT K WEP3530T3688 SEAT T WEP3510L1327 SLIDE COVER PLATE WEP3530L0737 HOSE SEAT WEP3530L0897 SEAT SIDE AIR BAG RIGHT WEP3530L0977 SEAT SIDE AIR BAG LEFT WEP3530L0847 SEAT AIR BAG WEP3530K3767 LIFT PROTECTION SHEET WEP596K0457 PUSHTURN RIVET WEP3530K3777 UNDER COVER RIGHT WEP3530K3787 UNDER COVER LEFT WEP3530K3057 OUTSIDE COVER RIGHT WEP3530K3068 OUTISDE COVER LEFT WEP3530K3027 INSIDE COVER RIGHT WEP3530K3037 INSIDE COVER LEFT WEP3530K7027 LID WEP3530K3608 ARMREST RIGHT K WEP3530T3698 ARMREST RIGHT T WEP3530K3708 ARMREST LEFT K WEP3530T3708 ARMREST LEFT T WEP3200K0567 INSULATED TIE WEP1270L6527 WASHER WEP3530L0167 GUIDE ROLLER SPRING WEP3530L0157 GUIDE ROLLER WEP3510L0047 MAIN BODY FRAME WEP3530L1468 UP/DOWN GEAR BLOCK WEP3200L0377 UP/DOWN SHAFT WEP3510L6057 UP/DOWN SHAFT BOLT WEP3200L3537 FITTING WEP3530L1457 GUIDE ROLLER C BLOCK WEP3530H1927 GUIDE ROLLER C WEP578AL0317 RUBBER RING WEP3530L1447 PINION C WEP3530L1547 GUIDE ROLLER B BLOCK WEP3200L0427 PINION B WEP3530H1937 GUIDE ROLLER B

70 Ref.No. Part No. Part Name & Description Remarks Per Unit 189 WEP2200L0337 UP/DOWN SHAFT HOLDER B WEP3510L0187 GROUNDING PLATE WEP3200L1767 UP/DOWN GEAR BOX A WEP3200L1797 UP/DOWN GEAR BOX B WEP3530L1417 UP/DOWN WORM WHEEL WEP3530L1018 UP/DOWN MOTOR WEP3530L2197 UP/DOWN MOTOR VELOCITY SENSOR WEP3530L1807 MOTOR VELOCITY SENSOR COVER WEP3530S6027 SCREW WEP596L9537 SCREW WEP2200L9677 SCREW WEP3200L9677 SCREW WEP3530L2187 UP/DOWN SENSOR WEP3510L1397 UP/DOWN SENSOR GEAR WEP3200L1847 UP/DOWN SENSOR INSTALL PLATE WEP590L6017 SCREW WEP3510L0227 UP/DOWN DRIVINBG INSTALL PLATE WEP3530L1038 WIDTH MOTOR WEP3530L2147 WIDTH MOTOR VELOCITY SENSOR 208 WEP2200L1107 WIDTH BELT WEP3530L1478 INTENSITY DRIVING BLOCK WEP3530L4957 INTENSITY SENSOR WEP760N9607 SCREW WEP3530L4488 AIR UNIT WEP3530L2487 TWIN TANK WEP3530L0607 CONNECTION L HOSE WEP3530L0597 SILICON HOSE WEP3530L ROW 3 WAY ELECTROMAGNETIC VALVE WEP3530L0297 ELECTROMAGNETIC VALVE RADIATION PLATE WEP3530S6017 SCREW WEP3210L0357 HOSE CLAMP WEP3530L2927 CONNECTION CORD FOR PUMP VALVE WEP3530L0717 FLOAT HOSE WEP3530L0727 PINCHING HOSE WEP3510L0327 MOTOR VIBRATIONPROOF RUBBER WEP3530K0537 TOP CASE WEP3530K0547 BOTTOM CASE WEP3510K0317 AIR UNIT INSTALL RUBBER WEP3530S9537 SCREW WEP3530S6037 SCREW WEP3530L1028 AIR PUMP FOR MASSAGE BLOCK WEP3510S9097 SCREW WEP3510L0027 BRUSHCLIP WEP3530L1438 WIDTH DRIVING BLOCK WEP3530L0337 HEAD PROTECTION CLOTH WEP3510L0027 BRUSHCLIP WEP3530L1047 ANTI HOOKING COVER RIGHT WEP3530L1067 ANTI HOOKING COVER LEFT WEP3530L0877 PINCHING AIR BAG RIGHT

71 Ref.No. Part No. Part Name & Description Remark Per Unit 238 WEP3530L0907 PINCHING AIR BAG LEFT WEP3530L0857 FLOAT AIR BAG RIGHT WEP3530L0937 FLOAT AIR BAG LEFT WEP3510L9687 SCREW WEP3510S0367 SNAP PIN WEP3200L0457 SNAP RIVET WEP3510L0107 FLOAT AIR BAG COVER RIGHT WEP3510L0537 FLOAT AIR BAG COVER LEFT WEP3510L0117 PINCHING AIR BAG COVER WEP3530L0127 AIR BAG FIXING PLATE RIGHT WEP3530L0527 AIR BAG FIXING PLATE LEFT WEP3510L0207 ECCENTRIC LING INSTALL PLATE RIGHT WEP3510L0217 ECCENTRIC LING INSTALL PLATE LEFT WEP3530L0197 HOSE GUIDE B WEP3510S9057 SCREW WEP3510L0137 T JOINT WEP3510L0167 TAPPING PLATE SPRING WEP3510L0477 INENSITY SENSOR PLATE WEP3510L0507 INTENSITY SENSOR PLATE GREASE COVER WEP3510L0497 SCREWRIVET WEP3530L2208 ROTATION SENSOR WEP3530L2148 WIDTH SENSOR INSTALL PLATE WEP3510L1887 WIDTH SENSOR INSTALL PLATE B WEP3510L1897 WIDTH SENSOR GREASE COVER WEP3510L9067 SCREW WEP3510L0488 WIDTH SENSOR PLATE WEP3530L0368 SNAP PIN WEP2200L3417 UP/DOWN BELT WEP005W8507 INSULATED TIE WEP3510L0037 PCB INSTALL PLATE WEP3530L2108 MAIN PCB WEP3510L0547 MASSAGE BLOCK COVER WEP3510L2897 CONNECTING CORD FOR POWER SOURCE B WEP3530L2240 SUB TRANSFORMER WEP3530S3138 CONTROLELR COVER RIGHT, ENGLISH WEP3530S3148 CONTROLLER COVER LEFT, ENGLISH WEP3530L2887 CONTROLLER CORD 1 WEP3530K3748 MASSAGE MECHANISM BLOCK 1 WEP3530K8209 P.C, K 1 WEP3530T8209 P.C, T 1 WEP3530L8789 OPERATION MANUAL, CANADA 1 Note:* Supplied from MEW-Japan