Architecture - Engineering - Planning

Transcription

1 rchitecture - Engineering - Planning Mansfield, Ohio New Philadelphia, Ohio Powell, Ohio phone phone phone fax fax fax SHOP DRWING REVIEW PROJECT NME: Westlake New Middle School JOB NO: 09-ED1-045C SUBMITTL : Switchboards SPEC. REFERENCE: MNUFCTURER: Eaton Cutler Hammer REVIEWED REVISE ND RESUBMIT REVIEWED S NOTED NOT CCEPTED Checking is only for conformance with the design concept of the project and compliance with the information given in the contract documents. The Contractor is responsible for dimensions to be confirmed and correlated at the job site. For information that pertains solely to the fabrication processes or to techniques of construction and for coordination of the work of all trades. : BY: TMM COMMENTS: SEE THE TTCHED DOCUMENTS

2 MKC SSOCITES, INC. RCHITECTS - ENGINEERS - PLNNERS 40 West 4th Street Mansfield Ohio SHOP DRWING REVIEW : PROJECT: Westlake New Lee Burneson Middle School JOB NO.: 09-ED1-045C SPECIFICTION : SWITCHBORDS (ONLY) SPECIFICTION NUMBER: MNUFCTURER: Eaton Cutler-Hammer FILE NME: COMMENTS: THE FOLLOWING COMMENTS HVE NOT BEEN MRKED ON THE TTCHED SHOP DRWINGS: GENERL S: 1. ll lugs shall be listed for aluminum and/or copper conductors. 2. The contractor is responsible to verify lug sizes with conductors used. 3. The contractor shall verify lug locations. 4. Switch arrangement or placement per section is the responsibility of the contractor. 5. Nameplate quantity and nomenclature is the responsibility of the contractor and as per Spec Section Final quantities shall be the responsibility of the contractor. 7. The SPD device at the switchboard shall be Cat no. SPD400480Y1. 8. Provide arc flash labeling per Spec Section MSB SPECIFIC S: 1. SURGE PROTECTION DEVICE SHLL BE MOUNTED T THE END OF THE SWITCHBORD (SECTION #1) WITH THE FRONT FCING THE WORKING SPCE ND FED FROM 100 MP SWITCH LOCTED IN SECTION #1 WITH NIPPLE BETWEEN. 2. THE GROUND FULT ELECTRIC TRIP UNIT POWER SHLL BE INTERNLLY WIRED, NO EXTERNL POWER REQUIRED. TPDP SPECIFIC S: 1. THE SWITCHBORD MIN SWITCH SHLL BE 600 VOLT RTED ND SHLL BE CLSS J. Page 1 of 1

3 rchitecture - Engineering - Planning Mansfield, Ohio New Philadelphia, Ohio Powell, Ohio phone phone phone fax fax fax SHOP DRWING REVIEW PROJECT NME: Westlake New Middle School JOB NO: 09-ED1-045C SUBMITTL : Panelboards SPEC. REFERENCE: MNUFCTURER: Eaton Cutler Hammer REVIEWED REVISE ND RESUBMIT REVIEWED S NOTED NOT CCEPTED Checking is only for conformance with the design concept of the project and compliance with the information given in the contract documents. The Contractor is responsible for dimensions to be confirmed and correlated at the job site. For information that pertains solely to the fabrication processes or to techniques of construction and for coordination of the work of all trades. : BY: TMM COMMENTS: SEE THE TTCHED DOCUMENTS

4 MKC SSOCITES, INC. RCHITECTS - ENGINEERS - PLNNERS 40 West 4th Street Mansfield Ohio SHOP DRWING REVIEW : PROJECT: Westlake New Lee Burneson Middle School JOB NO.: 09-ED1-045C SPECIFICTION : PNELBORDS (ONLY) SPECIFICTION NUMBER: MNUFCTURER: Eaton Cutler-Hammer FILE NME: COMMENTS: THE FOLLOWING COMMENTS HVE NOT BEEN MRKED ON THE TTCHED SHOP DRWINGS: GENERL S: 1. ll lugs shall be UL listed for aluminum conductors for the sizes as specified. 2. The contractor is responsible to verify lug sizes with conductors used. 3. The contractor shall verify lug locations. 4. Breaker arrangement or placement per tub is the responsibility of the contractor. 5. ny multi-section (tub) panelboard may be converted to single tub at the contractors option. 6. ll multi-section panelboards shall have full capacity conductors between each section, verify lugs meet conductor requirements. 7. ll multi-section (tub) panelboards shall have all tubs the same height. 8. Final quantities shall be the responsibility of the contractor. 9. The SPD device for the panelboards shall be Cat no. SPD160208Y Nameplate quantity and nomenclature is the responsibility of the contractor and as per Spec Section Provide arc flash labeling per Spec Section PNEL SPECIFIC S: 1. PNEL EP1:. THE (1) 20-2P SHLL BE CHNGED TO 15-2P FOR THE COOLER COND. B. THE 20-1P SHLL BE TOTL QUNTITY OF (40). C. THE (1) 25-2P SHLL REMIN BUT BE USED FOR THE FREEZER COND. D. THE (1) 60-2P SHLL BE REPLCED WITH 15-2P USED FOR THE FREEZER EVP. E. THE 30-1P SHLL BE TOTL QUNTITY OF (5). 2. PNEL KP1:. THE (2) 40-1P SHLL BE CHNGED TO (1) 50-2P FOR EQUIP. #35. B. DD (1) 30-1P SHLL BE USED FOR EQUIP. #34. C. THE (1) 20-2P WITH SHUNT TRIP SHLL BE REPLCED WITH 20-1P WITH SHUNT TRIP USED FOR EQUIP. #22. D. THE 20-1P SHLL BE TOTL QUNTITY OF (31), BOTH SECTIONS. E. THE 15-1P SHLL BE TOTL QUNTITY OF (11), BOTH SECTIONS. F. DD (1) 20-2P SHLL BE USED FOR EQUIP. # PNEL P3:. THE 20-1P SHLL BE TOTL QUNTITY OF (38), BOTH SECTIONS. Page 1 of 2

5 4. PNEL P2:. THE 20-1P SHLL BE TOTL QUNTITY OF (37), BOTH SECTIONS. B. THE 20-1P WITH SHUNT TRIP SHLL BE TOTL QUNTITY OF (13), BOTH SECTIONS. 5. PNEL P1C:. THE 30-2P DESIGNTED FOR SUH-1 SHLL BE CHNGED TO 15-2P. B. THE 40-2P DESIGNTED FOR CU-1 SHLL BE CHNGED TO 50-2P. Page 2 of 2

6 rchitecture - Engineering - Planning Mansfield, Ohio New Philadelphia, Ohio Powell, Ohio phone phone phone fax fax fax SHOP DRWING REVIEW PROJECT NME: Westlake New Middle School JOB NO: 09-ED1-045C SUBMITTL : Surge Protection Devices SPEC. REFERENCE: MNUFCTURER: Eaton Cutler-Hammer REVIEWED REVISE ND RESUBMIT REVIEWED S NOTED NOT CCEPTED Checking is only for conformance with the design concept of the project and compliance with the information given in the contract documents. The Contractor is responsible for dimensions to be confirmed and correlated at the job site. For information that pertains solely to the fabrication processes or to techniques of construction and for coordination of the work of all trades. : BY: TMM COMMENTS: THE FOLLOWING COMMENTS HVE NOT BEEN MRKED ON THE TTCHED SHOP DRWINGS: GENERL S: 1. The SPD device at the switchboard shall be Cat no. SPD400480Y1. 2. The SPD device for the panelboards shall be Cat no. SPD160208Y1. 3. Nameplate quantity and nomenclature is the responsibility of the contractor and as per Spec Section Provide arc flash labeling per Spec Section

7 rchitecture - Engineering - Planning Mansfield, Ohio New Philadelphia, Ohio Powell, Ohio phone phone phone fax fax fax SHOP DRWING REVIEW PROJECT NME: Westlake New Middle School JOB NO: 09-ED1-045C SUBMITTL : Transformers SPEC. REFERENCE: MNUFCTURER: Eaton Cutler-Hammer REVIEWED REVISE ND RESUBMIT REVIEWED S NOTED NOT CCEPTED Checking is only for conformance with the design concept of the project and compliance with the information given in the contract documents. The Contractor is responsible for dimensions to be confirmed and correlated at the job site. For information that pertains solely to the fabrication processes or to techniques of construction and for coordination of the work of all trades. : BY: TMM COMMENTS: THE FOLLOWING COMMENTS HVE NOT BEEN MRKED ON THE TTCHED SHOP DRWINGS: GENERL S: 1. Transformer T-PDP & T-TPDP shall be mounted exterior, weather shields required. 2. Nameplate quantity and nomenclature is the responsibility of the contractor and as per Spec Section Provide arc flash labeling per Spec Section

8 rchitecture - Engineering - Planning Mansfield, Ohio New Philadelphia, Ohio Powell, Ohio phone phone phone fax fax fax SHOP DRWING REVIEW PROJECT NME: Westlake New Middle School JOB NO: 09-ED1-045C SUBMITTL : Enclosed Controllers (Starters) SPEC. REFERENCE: MNUFCTURER: Eaton Cutler-Hammer REVIEWED REVISE ND RESUBMIT REVIEWED S NOTED NOT CCEPTED Checking is only for conformance with the design concept of the project and compliance with the information given in the contract documents. The Contractor is responsible for dimensions to be confirmed and correlated at the job site. For information that pertains solely to the fabrication processes or to techniques of construction and for coordination of the work of all trades. : BY: TMM COMMENTS: THE FOLLOWING COMMENTS HVE NOT BEEN MRKED ON THE TTCHED SHOP DRWINGS: 1. Final quantities are the responsibility of the Contractor. 2. ll starters shall include ground kit. 3. Starters for B-1 & B-2 must be NEM size 1 4. Submit manual motor starters for review. 5. Submit manual motor starters with hand-off-auto for review. 6. Submit motor starters switches for review. 7. Submit timer switches for review. 8. HU heat wheel starters, verify quantity. 9. Dock Leveler starter must be NEM size 1, coordinate with equipment for exact control functions required. 10. Submit starters for freezer and cooler condensers and evaporators 11. Provide the properly sized overload for each manual motor starter. 12. Nameplate quantity and nomenclature is the responsibility of the contractor and as per Spec Section Provide arc flash labeling per Spec Section

9 rchitecture - Engineering - Planning Mansfield, Ohio New Philadelphia, Ohio Powell, Ohio phone phone phone fax fax fax SHOP DRWING REVIEW PROJECT NME: Westlake New Middle School JOB NO: 09-ED1-045C SUBMITTL : Enclosed Switches(Disconnects) SPEC. REFERENCE: MNUFCTURER: Eaton Cutler-Hammer REVIEWED REVISE ND RESUBMIT REVIEWED S NOTED NOT CCEPTED Checking is only for conformance with the design concept of the project and compliance with the information given in the contract documents. The Contractor is responsible for dimensions to be confirmed and correlated at the job site. For information that pertains solely to the fabrication processes or to techniques of construction and for coordination of the work of all trades. : BY: TMM COMMENTS: THE FOLLOWING COMMENTS HVE NOT BEEN MRKED ON THE TTCHED SHOP DRWINGS: 1. Final quantities are the responsibility of the Contractor. 2. ll disconnects shall have lock-on provisions. 3. ll disconnects shall have a ground kit. 4. The dishwasher and booster heater disconnects shall be NEM 4X Stainless steel. 5. Provide aux. contact kits on all disconnects as required. 6. Submit disconnects for SUH-1 and CU-1 for review. 7. Disconnects for HWP-1 & HWP-2 shall have class J fuse spacing 8. Nameplate quantity and nomenclature is the responsibility of the contractor and as per Spec Section Provide arc flash labeling per Spec Section

10 Westlake City Schools Submittal Cover Sheet (To be filled out and submitted with each submittal) School Lee Burneson Middle School Contractor: _Turner Logistics_ Date 02/06/12 Item: SWITCHGER & PNEL BORDS Specification Section: _ Sub Specification Section: _262200, , , _ Contractor s Submittal # Revision # 0 Submittal Type PDF Lead Time fter pproval (wks) _10_ Manuf/Supplier: _ETON ELECTRICL _ Intended rea of Use, Drawing # and Detail Reference: Contractor Stamp CM Stamp PED ETON ELECTRICL Mike Mammone 02/06/12 TURNER/RESOURCE Reviewed for general acceptance only. This review does not relieve the Contractor of the responsibility for making the work conform to the requirements of the contract. The Contractor is responsible for all dimensions, correct fabrication and accurate fit with the work of other trades. SUBJECT TO RCHITECT S PL Signed: Date: CM Submittal #: rchitect Stamp Engineer Stamp

11 1422 Euclid venue Suite 1400 Cleveland, OH Telephone (216) Fax (216) To: Dave Conant, Project Engineer Company: Turner Construction ddress: Hilliard Blvd. Westlake, OH Phone: Date: 02/06/12 T R N S M I T T L From: Dale Schmid Re: Middle School Eaton Electrical Submittals The following is included: No. of Drawing No. Dated Description Copies 1 pdf 02/06/12 Switchgear, Panelboard submittal Remarks: 1. For pproval. 2. To be approved for fabrication by no later than 4/01/12. Thank you. Sent for: pproval Correction Files Information Estimate Signature Comment Turner Logistics, LLC

12 Burneson Middle School Submittal for pproval General Order Volume 1 of 1 Equipment: Engineering Services & Systems Switchboards Panelboards Surge Protection Device Dry Type Transformers Enclosed Control (NEM) Safety Switches Date: 01/27/2012 PEPCO ESTLKE OH PO# S TURNER LOGISTICS 2012, ll Rights Reserved

13 ETON Cutler Hammer Michael Mammone Phone: Neg# LT160914Y101 lt# 0005 Job Name: Burneson Middle School 13:14:41 Customer Bill of Material 1 ESS Study-BidManager Short-Circuit and Overcurrent Coordination Studies Short circuit and overcurrent coordination studies would be detailed only for the proposed equipment supplied by the sales office and listed in the Bill of Material. Short circuit currents would be calculated and compared to the proposed equipment ratings down to the low voltage panelboards. Overcurrent coordination plots and recommended settings would be provided for the proposed adjustable-trip protective devices. In order to minimize the number of short circuit bus nodes and coordination plots, similar documentation may be used for system redundancy. The accuracy and delivery of the study are greatly dependent upon timely receipt of accurate field information provided by others. Selective Coordination nalysis is NOT included. Selective Coordination nalysis of Elevators, Emergency Systems, Legally Required Standby Systems, and Critical Operations Power Systems per the 2011 NEC requirements (detailed in rticles , , , , and ) is NOT included in the scope of work. PE Review / Stamp will be provided by a registered professional engineer in the state of Ohio. Study Lead Times Lead time for data request = within 2 weeks of receipt of one-line, specifications, detailed bill of material, and vista order paper. Lead time for final study results = 3-4 weeks after all remaining data received, including equipment submittals and answers to data request. Eaton s quotation is based on the specific overcurrent protective device frame sizes shown on the contract drawings unless specifically listed otherwise in our Bill of Material. Where only circuit breaker trip sizes and/or fuse sizes are shown on the contract drawings, Eaton's quotation is based on the minimum frame size breaker or fusible switch which can accommodate those trip sizes/fuse sizes unless specifically listed otherwise in our Bill of Material. Protective devices will have short circuit interrupting ratings as indicated in the contract documents unless specifically listed otherwise in our Bill of Material. Where Selective Coordination requirements are specified in the contract documents and/or are required by the legally adopted version of the National Electrical Code (NEC) or other codes, a short circuit study indicating the fault current at each bus and a selective coordination study is required. If Eaton is to perform the short circuit/coordination study, this will be performed at an appropriate price addition, unless a short circuit/coordination study is already specifically listed in our Bill of Material as included. The study will determine if there are any situations or devices which do not comply with selective coordination requirements of the legally adopted version of the National Electric Code. It is the project design engineer s responsibility to propose changes needed for upgrading of protective device type or frame size to meet Selective Coordination requirements. If desired, at an appropriate price addition, Eaton can assist the design engineer in developing the most economically feasible changes to the design and/or equipment to meet code requirements. These upgraded changes in type or frame size will only be supplied at an appropriate price increase. Notes: 1) Eaton will not be responsible for any costs associated with required additional physical space, additional equipment, or extra installation requirements because of the increased size or required extra equipment.

14 ETON Cutler Hammer Michael Mammone Phone: Neg# LT160914Y101 lt# 0005 Job Name: Burneson Middle School 13:14:41 Customer Bill of Material 2) The requirement for mandated selective coordination per NEC may substantially increase the arc-flash energy available at the various pieces of electrical equipment. n rc-flash study to determine the procedures and Personal Protective Equipment required is strongly recommended for personnel safety. can provide the rc-flash study at additional cost. 1 ESS Study-BidManager 1 2 Weeks Lead Time for Data Request Submittal Weeks Lead Time for Study Completion 1 Quoted by Bid Manager 1 PE Review Stamp Required (Ohio) Designations: Study ll orders must be released for manufacture within 90 days of date of order entry. If approval drawings are required, drawings must be returned approved for release within 60 days of mailing. If drawings are not returned accordingly, and/or if shipment is delayed for any reason, the price of the order will increase by 1.0% per month or fraction there of for the time the shipment is delayed.

15 CHESS_ST PREPRED BY ChristopherJCross PED BY JOB NME Burneson Middle School DESIGNTION Study DRWING NEG-LT NUMBER OF 2

16 PREPRED BY ChristopherJCross PED BY JOB NME Burneson Middle School DESIGNTION Study DRWING NEG-LT NUMBER OF 2

17 ETON Cutler Hammer Michael Mammone Phone: Neg# LT160914Y101 lt# 0005 Job Name: Burneson Middle School 13:14:49 Customer Bill of Material 1 PRLC Switchboard Pow-R-Line C Switchboard, Front ccess/ Front and Rear lign, Type 1 480Y/277V 3-Phase 4-Wire, 2500 luminum, Minimum Interrupt Rating: 65k, Bus Bracing Rating: 65k 1 Pow-R-Line C 3 Vertical Isol. Barrier (Service Entrance) 1 Service Entrance Label 4 Copper.25 X 2.0 Ground Bus mp L Main Structure 42 Nameplate 1 Bottom Fed Switch 1 Ground fault protection mp L Distribution Structure 3 Gutter Doors Pole Bolted Pressure Switch, Class L fuse clips provided, (fuses provided by others), (7) 3/0-750 kcmil, Mechanical, 2 600/600V 3 Pole Chas. Mtd. FDPW Sw [J], (2) #4-500 kcmil, Mechanical 1 400/600V 3 Pole Chas. Mtd. FDPW Sw [J], (2) 3/0-250 kcmil, Mechanical 2 200/600V 3 Pole Chas. Mtd. FDPB Sw [J], (1) #4-300 kcmil, Mechanical 2 100/100/600V 3 Pole Chas. Mtd. FDPW Sw [J], (1) #14-1/0, Mechanical 9 30/30/600V 3 Pole Chas. Mtd. FDPW Sw [J], (1) #14-1/0, Mechanical 7 60/60/600V 3 Pole Chas. Mtd. FDPW Sw [J], (1) #14-1/0, Mechanical Designations: MSB 1 PRLC Switchboard Pow-R-Line C Switchboard, Front ccess/ Front and Rear lign, Type 1 208Y/120V 3-Phase 4-Wire, 600 luminum, Minimum Interrupt Rating: 35k, Bus Bracing Rating: 65k 1 Pow-R-Line C 2 Neutral Rating - 200% 1 Vertical Isol. Barrier 2 Copper.25 X 2.0 Ground Bus mp L Main Structure 6 Nameplate 1 Bottom Fed Switch mp L Distribution Structure 1 Gutter Doors 1 600/250V Ind. Mtd. Main 3P FDPW Fus. Sw. R-Fuse, (2) #4-500 kcmil, Mechanical, Bottom 3 400/600V 3 Pole Chas. Mtd. FDPW Sw [J], (1) kcmil, Mechanical 1 100/100/600V 3 Pole Chas. Mtd. FDPW Sw [J], (1) #14-1/0, Mechanical Designations: TPDP

18 ETON Cutler Hammer Michael Mammone Phone: Neg# LT160914Y101 lt# 0005 Job Name: Burneson Middle School 13:14:49 Customer Bill of Material 1 PRLC Switchboard Pow-R-Line C Switchboard, Front ccess/ Front and Rear lign, Type 1 208Y/120V 3-Phase 4-Wire, 1200 luminum, Minimum Interrupt Rating: 42k, Bus Bracing Rating: 65k 1 Pow-R-Line C 2 Vertical Isol. Barrier 3 Copper.25 X 2.0 Ground Bus mp L Main Structure 11 Nameplate 1 Bottom Fed Switch mp L Distribution Structure 2 Gutter Doors /250V Ind. Mtd. Main 3P FDPW Fus. Sw. L-Fuse, (4) #4-500 kcmil, Mechanical, Bottom 2 400/600V 3 Pole Chas. Mtd. FDPW Sw [J], (1) kcmil, Mechanical 1 100/100/600V 3 Pole Chas. Mtd. FDPW Sw [J], (1) #14-1/0, Mechanical 1 60/60/600V 3 Pole Chas. Mtd. FDPW Sw [J], (1) #14-1/0, Mechanical 4 200/600V 3 Pole Chas. Mtd. FDPB Sw [J], (1) #4-300 kcmil, Mechanical Designations: PDP ll orders must be released for manufacture within 90 days of date of order entry. If approval drawings are required, drawings must be returned approved for release within 60 days of mailing. If drawings are not returned accordingly, and/or if shipment is delayed for any reason, the price of the order will increase by 1.0% per month or fraction there of for the time the shipment is delayed.

19 Switchboard General Information Pow-R-Line C -Specifications Quantity: 1 lignment: Front ccess/ Front and Rear lign Service: 480Y/277V 3-Phase 4-Wire Minimum Interrupt Rating: 65 k Bus Specifications Bus mps: 2500 Bus Bracing Rating: 65k Neutral mps: 2500 Bus Material: luminum Heat Test Copper.25 X 2.0 Ground Bus Bolted To Frame, (1) 350 kcmil Ground Lug Incoming Information Incoming Entry: Bottom Incoming Location: Right Incoming Qty & Size: Terminals, Mechanical, (7) 3/0-750 kcmil, Bottom Structure Specifications Service Entrance Enclosure Type: Type 1 Nameplates: Screw On - White with Black letters Enclosure properties Struct # Description/Modifications 1 50x chassis mounted feeders (Feeder Structure) (Hinged Gutter Doors) 2 50x chassis mounted feeders (Feeder Structure) (Hinged Gutter Doors) Vertical isolating barrier 3 50x chassis mounted feeders (Feeder Structure) (Hinged Gutter Doors) Vertical isolating barrier 4 Bottom incoming main device (Incoming Main Device/MLO Section) Vertical isolating barrier PREPRED BY orderentryepod PED BY JOB NME Burneson Middle School DESIGNTION MSB DRWING Sumter, SC Switchboards Customer ppr. NEG-LT NUMBER OF 5

20 Front View * 10 2 * 3 * 4 * Power Flow Floor Plan See For Floor Plan Detail Top/Bottom Cable Exit See For Floor Plan Detail Top/Bottom Cable Exit See For Floor Plan Detail Top/Bottom Cable Exit See For See For See For Detail Conduit readetail Conduit readetail Conduit rea Total of 4 Structures, Total Width of 153 Inches Total of 4 Structures, Total Weight of 2670 Weight-Lbs. Width-Inches Width-MM Depth-Inches Depth-MM Height-Inches Height-MM Weight-Lbs.(Est.) Weight-Kg.(Est.) PREPRED BY orderentryepod PED BY JOB NME DESIGNTION Burneson Middle School MSB DRWING Sumter, SC Switchboards Customer ppr. NEG-LT NUMBER OF 5

21 Switchboard Units Information Str# Unit Description/Modifications Nameplate 1 1 Feeder Switch - Chassis Mtd-30/30/600V 3 Pole Chas. Mtd. FDPW Sw [J] Terminals, Mechanical, (1) #14-1/0 HWP-1 HWP-2 2 Feeder Switch - Chassis Mtd-30/30/600V 3 Pole Chas. Mtd. FDPW Sw [J] Terminals, Mechanical, (1) #14-1/0 3 Feeder Switch - Chassis Mtd-60/60/600V 3 Pole Chas. Mtd. FDPW Sw [J] Terminals, Mechanical, (1) #14-1/0 EF-25 SPRE SPRE DISHWSHER 4 Feeder Switch - Chassis Mtd-60/60/600V 3 Pole Chas. Mtd. FDPW Sw [J] Terminals, Mechanical, (1) #14-1/0 HU-6 S. RTU-1 5 Feeder Switch - Chassis Mtd-60/60/600V 3 Pole Chas. Mtd. FDPW Sw [J] Terminals, Mechanical, (1) #14-1/0 HU-4 S. HU-5 S. 2 6 Feeder Switch - Chassis Mtd-60/60/600V 3 Pole Chas. Mtd. FDPW Sw [J] Terminals, Mechanical, (1) #14-1/0 7 Feeder Switch - Chassis Mtd-60/60/600V 3 Pole Chas. Mtd. FDPW Sw [J] Terminals, Mechanical, (1) #14-1/0 8 Feeder Switch - Chassis Mtd-60/60/600V 3 Pole Chas. Mtd. FDPW Sw [J] Terminals, Mechanical, (1) #14-1/0 9 Feeder Switch - Chassis Mtd-60/60/600V 3 Pole Chas. Mtd. FDPW Sw [J] Terminals, Mechanical, (1) #14-1/0 1 Feeder Switch - Chassis Mtd-30/30/600V 3 Pole Chas. Mtd. FDPW Sw [J] Terminals, Mechanical, (1) #14-1/0 2 Feeder Switch - Chassis Mtd-30/30/600V 3 Pole Chas. Mtd. FDPW Sw [J] Terminals, Mechanical, (1) #14-1/0 3 Feeder Switch - Chassis Mtd-30/30/600V 3 Pole Chas. Mtd. FDPW Sw [J] Terminals, Mechanical, (1) #14-1/0 4 Feeder Switch - Chassis Mtd-30/30/600V 3 Pole Chas. Mtd. FDPW Sw [J] Terminals, Mechanical, (1) #14-1/0 5 Feeder Switch - Chassis Mtd-30/30/600V 3 Pole Chas. Mtd. FDPW Sw [J] Terminals, Mechanical, (1) #14-1/0 6 Feeder Switch - Chassis Mtd-30/30/600V 3 Pole Chas. Mtd. FDPW Sw [J] Terminals, Mechanical, (1) #14-1/0 TS-1 HU-2 S. CWP-1 SPRE PNEL L3 PNEL HP3 PNEL HP1 PNEL HP2 HU-6R HU-6HW HU-5R HU-5HW HU-4R HU-3HW HU-3S HU-3R HU-2R HU-2HW HU-1S HU-1R PREPRED BY orderentryepod PED BY JOB NME Burneson Middle School DESIGNTION MSB DRWING Sumter, SC Switchboards Customer ppr. NEG-LT NUMBER OF 5

22 3 7 Feeder Switch - Chassis Mtd-30/30/600V 3 Pole Chas. Mtd. FDPW Sw [J] Terminals, Mechanical, (1) #14-1/0 8 Feeder Switch - Chassis Mtd-100/100/600V 3 Pole Chas. Mtd. FDPW Sw [J] Terminals, Mechanical, (1) #14-1/0 9 Feeder Switch - Chassis Mtd-100/100/600V 3 Pole Chas. Mtd. FDPW Sw [J] Terminals, Mechanical, (1) #14-1/0 10 Feeder Switch - Chassis Mtd-200/600V 3 Pole Chas. Mtd. FDPB Sw [J] Terminals, Mechanical, (1) #4-300 kcmil 1 Feeder Switch - Chassis Mtd-200/600V 3 Pole Chas. Mtd. FDPB Sw [J] Terminals, Mechanical, (1) #4-300 kcmil 2 Feeder Switch - Chassis Mtd-400/600V 3 Pole Chas. Mtd. FDPW Sw [J] Terminals, Mechanical, (2) 3/0-250 kcmil 3 Feeder Switch - Chassis Mtd-600/600V 3 Pole Chas. Mtd. FDPW Sw [J] Terminals, Mechanical, (2) #4-500 kcmil 4 Feeder Switch - Chassis Mtd-600/600V 3 Pole Chas. Mtd. FDPW Sw [J] Terminals, Mechanical, (2) #4-500 kcmil DCK LVLR BTR HTR HPC-1 SPRE TVSS PNEL L2 PNEL L1 PNEL TS-2 XFMR T-TPDP CC-1 XFMR T-PDP 4 Main Switch - Ind Mtd Pole Bolted Pressure Switch, Class L fuse clips provided, (fuses provided by others) Terminals, Mechanical, (7) 3/0-750 kcmil, Bottom MIN SWITCH Ground fault protection (with electric trip switch and test panel) Bottom Fed Switch PREPRED BY orderentryepod PED BY JOB NME Burneson Middle School DESIGNTION MSB DRWING Sumter, SC Switchboards Customer ppr. NEG-LT NUMBER OF 5

23 PREPRED BY orderentryepod PED BY NEG-LT NUMBER 1 JOB NME DESIGNTION Switchboards Burneson Middle School MSB DRWING Sumter, SC Customer ppr OF 5

24 Switchboard General Information Pow-R-Line C -Specifications Quantity: 1 lignment: Front ccess/ Front and Rear lign Service: 208Y/120V 3-Phase 4-Wire Minimum Interrupt Rating: 35 k Bus Specifications Bus mps: 600 Bus Bracing Rating: 65k Neutral mps: % Rated Neutral Bus Material: luminum Heat Test Copper.25 X 2.0 Ground Bus Bolted To Frame, (1) 350 kcmil Ground Lug Incoming Information Incoming Entry: Bottom Incoming Location: Left Incoming Qty & Size: Terminals, Mechanical, (2) #4-500 kcmil, Bottom Neutral Terminals Double bove Qty. for 200% Rating Structure Specifications Non Service Entrance Enclosure Type: Type 1 Nameplates: Screw On - White with Black letters Enclosure properties Struct # Description/Modifications 1 Bottom incoming main device (Incoming Main Device/MLO Section) Vertical isolating barrier 2 50x chassis mounted feeders (Feeder Structure) (Hinged Gutter Doors) PREPRED BY orderentryepod PED BY JOB NME Burneson Middle School DESIGNTION TPDP DRWING Sumter, SC Switchboards Customer ppr. NEG-LT NUMBER OF 4

25 Front View 1 * 2 * Power Flow Floor Plan See For Floor Plan Detail Top/Bottom Cable Exit See For Detail Conduit rea Total of 2 Structures, Total Width of 66 Inches Total of 2 Structures, Total Weight of 925 Weight-Lbs. Width-Inches Width-MM Depth-Inches Depth-MM Height-Inches Height-MM Weight-Lbs.(Est.) Weight-Kg.(Est.) PREPRED BY orderentryepod PED BY JOB NME Burneson Middle School DESIGNTION TPDP DRWING Sumter, SC Switchboards Customer ppr. NEG-LT NUMBER OF 4

26 Switchboard Units Information Str# Unit Description/Modifications Nameplate 1 Main Switch - Ind Mtd-600/250V Ind. Mtd. Main 3P FDPW Fus. Sw. R-Fuse Terminals, Mechanical, (2) #4-500 kcmil, Bottom MIN SWITCH Bottom Fed Switch 2 1 Feeder Switch - Chassis Mtd-100/100/600V 3 Pole Chas. Mtd. FDPW Sw [J] Terminals, Mechanical, (1) #14-1/0 CONTRCTOR TO IDE PIN CONNECTOR/REDUCER. 2 Feeder Switch - Chassis Mtd-400/600V 3 Pole Chas. Mtd. FDPW Sw [J] Terminals, Mechanical, (1) kcmil 3 Feeder Switch - Chassis Mtd-400/600V 3 Pole Chas. Mtd. FDPW Sw [J] Terminals, Mechanical, (1) kcmil 4 Feeder Switch - Chassis Mtd-400/600V 3 Pole Chas. Mtd. FDPW Sw [J] Terminals, Mechanical, (1) kcmil T1B SPRE T3 T2 T1 PREPRED BY orderentryepod PED BY JOB NME Burneson Middle School DESIGNTION TPDP DRWING Sumter, SC Switchboards Customer ppr. NEG-LT NUMBER OF 4

27 PREPRED BY orderentryepod PED BY NEG-LT NUMBER 1 JOB NME DESIGNTION Switchboards Burneson Middle School TPDP DRWING Sumter, SC Customer ppr OF 4

28 Switchboard General Information Pow-R-Line C -Specifications Quantity: 1 lignment: Front ccess/ Front and Rear lign Service: 208Y/120V 3-Phase 4-Wire Minimum Interrupt Rating: 42 k Bus Specifications Bus mps: 1200 Bus Bracing Rating: 65k Neutral mps: 1200 Bus Material: luminum Heat Test Copper.25 X 2.0 Ground Bus Bolted To Frame, (1) 350 kcmil Ground Lug Incoming Information Incoming Entry: Bottom Incoming Location: Left Incoming Qty & Size: Terminals, Mechanical, (4) #4-500 kcmil, Bottom Structure Specifications Non Service Entrance Enclosure Type: Type 1 Nameplates: Screw On - White with Black letters Enclosure properties Struct # Description/Modifications 1 Bottom incoming main device (Incoming Main Device/MLO Section) Vertical isolating barrier 2 50x chassis mounted feeders (Feeder Structure) (Hinged Gutter Doors) Vertical isolating barrier 3 50x chassis mounted feeders (Feeder Structure) (Hinged Gutter Doors) PREPRED BY orderentryepod PED BY JOB NME Burneson Middle School DESIGNTION PDP DRWING Sumter, SC Switchboards Customer ppr. NEG-LT NUMBER OF 4

29 Front View 1 * 2 * 3 * Power Flow Floor Plan See For Floor Plan Detail Top/Bottom Cable Exit See For Floor Plan Detail Top/Bottom Cable Exit See For See For Detail Conduit readetail Conduit rea Total of 3 Structures, Total Width of 102 Inches Total of 3 Structures, Total Weight of 1390 Weight-Lbs. Width-Inches Width-MM Depth-Inches Depth-MM Height-Inches Height-MM Weight-Lbs.(Est.) Weight-Kg.(Est.) PREPRED BY orderentryepod PED BY JOB NME Burneson Middle School DESIGNTION PDP DRWING Sumter, SC Switchboards Customer ppr. NEG-LT NUMBER OF 4

30 Switchboard Units Information Str# Unit Description/Modifications Nameplate 1 Main Switch - Ind Mtd-1200/250V Ind. Mtd. Main 3P FDPW Fus. Sw. L-Fuse Terminals, Mechanical, (4) #4-500 kcmil, Bottom MIN SWITCH uxiliary switch: N Bottom Fed Switch Feeder Switch - Chassis Mtd-60/60/600V 3 Pole Chas. Mtd. FDPW Sw [J] Terminals, Mechanical, (1) #14-1/0 uxiliary switch: N CONTRCTOR TO IDE PIN CONNECTOR/CBLE REDUCERS 2 Feeder Switch - Chassis Mtd-100/100/600V 3 Pole Chas. Mtd. FDPW Sw [J] Terminals, Mechanical, (1) #14-1/0 uxiliary switch: N 3 Feeder Switch - Chassis Mtd-400/600V 3 Pole Chas. Mtd. FDPW Sw [J] Terminals, Mechanical, (1) kcmil uxiliary switch: N 4 Feeder Switch - Chassis Mtd-400/600V 3 Pole Chas. Mtd. FDPW Sw [J] Terminals, Mechanical, (1) kcmil uxiliary switch: N 1 Feeder Switch - Chassis Mtd-200/600V 3 Pole Chas. Mtd. FDPB Sw [J] Terminals, Mechanical, (1) #4-300 kcmil uxiliary switch: N 2 Feeder Switch - Chassis Mtd-200/600V 3 Pole Chas. Mtd. FDPB Sw [J] Terminals, Mechanical, (1) #4-300 kcmil uxiliary switch: N 3 Feeder Switch - Chassis Mtd-200/600V 3 Pole Chas. Mtd. FDPB Sw [J] Terminals, Mechanical, (1) #4-300 kcmil uxiliary switch: N 4 Feeder Switch - Chassis Mtd-200/600V 3 Pole Chas. Mtd. FDPB Sw [J] Terminals, Mechanical, (1) #4-300 kcmil uxiliary switch: N CONTRCTOR TO IDE CBLE REDUCER/CONNECTOR. P2B P3B SPRE P1C P1B P1 SPRE KP1 P2 P3 PREPRED BY orderentryepod PED BY JOB NME Burneson Middle School DESIGNTION PDP DRWING Sumter, SC Switchboards Customer ppr. NEG-LT NUMBER OF 4

31 PREPRED BY orderentryepod PED BY NEG-LT NUMBER 1 JOB NME DESIGNTION Switchboards Burneson Middle School PDP DRWING Sumter, SC Customer ppr OF 4

32 ETON Cutler Hammer Michael Mammone Phone: Neg# LT160914Y101 lt# 0005 Job Name: Burneson Middle School 13:15:33 Customer Bill of Material 1 Pow-R-Line1a 42 Circuits, 100, Fully Rated, 208Y/120V 3Ph 4W, luminum Bus, 18k IC,60, 3P QBHW-H Main Breaker[Top Fed], Surface Mounted 1 60, 3P QBHW-H Main Breaker 24 1P QBHW Branch Provision Only 12 20, 1P QBHW Branch Breaker 6 20, 1P QBHW Branch Breaker, w/ Shunt Trip 1 Std. Bolted l Ground Bar (l/cu Cable) 1 Panel Nameplate - White with Black Letters - Screw on 1 Circuit Directory - Metal Frame with Plastic Cover 1 Type 1 Enclosure:EZB2048R 1 EZ Trim, Door in Door, Concealed Hardware:EZT2048S 1 CONTRCTOR TO IDE PIN CONNECTOR/CBLE REDUCER. Designations: P2B 1 Pow-R-Line1a 42 Circuits, 100, Fully Rated, 208Y/120V 3Ph 4W, luminum Bus, 10k IC,60, 3P BB-H Main Breaker[Top Fed], Surface Mounted 1 60, 3P BB-H Main Breaker 10 20, 1P BB Branch Breaker 2 40, 2P BB Branch Breaker 22 1P BB Branch Provision Only 5 20, 1P BB Branch Breaker, w/ Shunt Trip 1 Std. Bolted l Ground Bar (l/cu Cable) 1 Panel Nameplate - White with Black Letters - Screw on 1 Circuit Directory - Metal Frame with Plastic Cover 1 Type 1 Enclosure:EZB2048R 1 EZ Trim, Door in Door, Concealed Hardware:EZT2048S 1 CONTRCTOR TO IDE PIN CONNECTOR/CBLE REDUCER. Designations: P3B

33 ETON Cutler Hammer Michael Mammone Phone: Neg# LT160914Y101 lt# 0005 Job Name: Burneson Middle School 13:15:33 Customer Bill of Material 1 Pow-R-Line2a 42 Circuits, 100, Fully Rated, 208Y/120V 3Ph 4W, luminum Bus, 35k IC,100, Main Lugs Only[Top Fed], Surface Mounted 1 100, Main Lugs Only 15 20, 1P GHQ Branch Breaker 1 20, 2P GHB Branch Breaker 1 40, 2P GHB Branch Breaker 2 15, 2P GHB Branch Breaker 1 30, 2P GHB Branch Breaker 17 15, 1P GHQ Branch Breaker 1 Std. Bolted l Ground Bar (l/cu Cable) 1 Panel Nameplate - White with Black Letters - Screw on 1 Circuit Directory - Metal Frame with Plastic Cover 1 Type 1 Enclosure:EZB2042R 1 EZ Trim, Door in Door, Concealed Hardware:EZT2042S Designations: P1C 1 Pow-R-Line3a 42 Circuits, 100, Fully Rated, 480Y/277V 3Ph 4W, luminum Bus, 50k IC,100, Main Lugs Only[Top Fed], Surface Mounted 1 100, Main Lugs Only 11 20, 1P HFD Branch Breaker 14 1P HFD Branch Provision Only 17 15, 1P HFD Branch Breaker 1 Std. Bolted l Ground Bar (l/cu Cable) 1 Panel Nameplate - White with Black Letters - Screw on 1 Circuit Directory - Metal Frame with Plastic Cover 1 Type 1 Enclosure:EZB2060R 1 EZ Trim, Door in Door, Concealed Hardware:EZT2060S Designations: HP1

34 ETON Cutler Hammer Michael Mammone Phone: Neg# LT160914Y101 lt# 0005 Job Name: Burneson Middle School 13:15:33 Customer Bill of Material 1 Pow-R-Line2a 42 Circuits, 100, Fully Rated, 480Y/277V 3Ph 4W, luminum Bus, 14k IC,60, 3P GHB Main Breaker[Top Fed], Surface Mounted 1 60, 3P GHB Main Breaker 13 20, 1P GHQ Branch Breaker 18 1P GHQ Branch Provision Only 11 15, 1P GHQ Branch Breaker 1 Std. Bolted l Ground Bar (l/cu Cable) 1 Panel Nameplate - White with Black Letters - Screw on 1 Circuit Directory - Metal Frame with Plastic Cover 1 Type 1 Enclosure:EZB2042R 1 EZ Trim, Door in Door, Concealed Hardware:EZT2042S Designations: HP2 1 Pow-R-Line2a 42 Circuits, 100, Fully Rated, 480Y/277V 3Ph 4W, luminum Bus, 14k IC,60, 3P GHB Main Breaker[Top Fed], Surface Mounted 1 60, 3P GHB Main Breaker 14 20, 1P GHQ Branch Breaker 18 1P GHQ Branch Provision Only 10 15, 1P GHQ Branch Breaker 1 Std. Bolted l Ground Bar (l/cu Cable) 1 Panel Nameplate - White with Black Letters - Screw on 1 Circuit Directory - Metal Frame with Plastic Cover 1 Type 1 Enclosure:EZB2042R 1 EZ Trim, Door in Door, Concealed Hardware:EZT2042S Designations: HP3 1 Pow-R-Line3a 42 Circuits, 250, Fully Rated, 480Y/277V 3Ph 4W, luminum Bus, 50k IC,250, Main Lugs Only[Top Fed], Surface Mounted 1 250, Main Lugs Only 9 1P HFD Branch Provision Only 33 20, 1P HFD Branch Breaker 1 Std. Bolted l Ground Bar (l/cu Cable) 1 Panel Nameplate - White with Black Letters - Screw on 1 Circuit Directory - Metal Frame with Plastic Cover 1 Type 1 Enclosure:EZB2060R 1 EZ Trim, Door in Door, Concealed Hardware:EZT2060S Designations: L1

35 ETON Cutler Hammer Michael Mammone Phone: Neg# LT160914Y101 lt# 0005 Job Name: Burneson Middle School 13:15:33 Customer Bill of Material 1 Pow-R-Line2a 42 Circuits, 100, Fully Rated, 480Y/277V 3Ph 4W, luminum Bus, 14k IC,100, 3P GHB Main Breaker[Top Fed], Surface Mounted 1 100, 3P GHB Main Breaker 27 20, 1P GHQ Branch Breaker 9 1P GHQ Branch Provision Only 3 20, 2P GHB Branch Breaker 1 Std. Bolted l Ground Bar (l/cu Cable) 1 Panel Nameplate - White with Black Letters - Screw on 1 Circuit Directory - Metal Frame with Plastic Cover 1 Type 1 Enclosure:EZB2042R 1 EZ Trim, Door in Door, Concealed Hardware:EZT2042S Designations: L2 1 Pow-R-Line2a 30 Circuits, 100, Fully Rated, 480Y/277V 3Ph 4W, luminum Bus, 14k IC,60, 3P GHB Main Breaker[Top Fed], Surface Mounted 1 60, 3P GHB Main Breaker 16 20, 1P GHQ Branch Breaker 12 1P GHQ Branch Provision Only 1 20, 2P GHB Branch Breaker 1 Std. Bolted l Ground Bar (l/cu Cable) 1 Panel Nameplate - White with Black Letters - Screw on 1 Circuit Directory - Metal Frame with Plastic Cover 1 Type 1 Enclosure:EZB2036R 1 EZ Trim, Door in Door, Concealed Hardware:EZT2036S Designations: L3

36 ETON Cutler Hammer Michael Mammone Phone: Neg# LT160914Y101 lt# 0005 Job Name: Burneson Middle School 13:15:33 Customer Bill of Material 1 Pow-R-Line2a Multi-Section Panel:2 Sections, 84 Circuits, 400, Fully Rated, 208Y/120V 3Ph 4W, luminum Bus, 35k IC,400, Main Lugs Only[Top Fed], Surface Mounted 2 400, Main Lugs Only 1 400, Through-Feed Lugs 62 20, 1P GHQ Branch Breaker 11 1P GHQ Branch Provision Only 1 20, 2P GHB Branch Breaker 3 15, 1P GHQ Branch Breaker 1 30, 2P GHB Branch Breaker 2 50, 2P GHB Branch Breaker 2 Std. Bolted l Ground Bar (l/cu Cable) 2 Panel Nameplate - White with Black Letters - Screw on 2 Circuit Directory - Metal Frame with Plastic Cover 2 Type 1 Enclosure:EZB2060R 2 EZ Trim, Door in Door, Concealed Hardware:EZT2060S 1 COMPRESSION LUGS ON THRU FEED LUGS ONLY Designations: P1B 1 Pow-R-Line1a 42 Circuits, 225, Fully Rated, 208Y/120V 3Ph 4W, luminum Bus, 22k IC,200, 3P EDB Main Breaker[Top Fed], 225, Through-Feed Lugs, Surface Mounted 1 200, 3P EDB Main Breaker 1 225, Through-Feed Lugs 4 25, 1P QBHW Branch Breaker 8 1P QBHW Branch Provision Only 9 20, 1P QBHW Branch Breaker, w/ Shunt Trip 20 20, 1P QBHW Branch Breaker 1 Std. Bolted l Ground Bar (l/cu Cable) 1 Panel Nameplate - White with Black Letters - Screw on 1 Circuit Directory - Metal Frame with Plastic Cover 1 Type 1 Enclosure:EZB2060R 1 EZ Trim, Door in Door, Concealed Hardware:EZT2060S 1 COMPRESSION LUGS ON THRU FEED LUGS ONLY Designations: P2 (1)

37 ETON Cutler Hammer Michael Mammone Phone: Neg# LT160914Y101 lt# 0005 Job Name: Burneson Middle School 13:15:33 Customer Bill of Material 1 Pow-R-Line2a Multi-Section Panel:2 Sections, 84 Circuits, 400, Fully Rated, 208Y/120V 3Ph 4W, luminum Bus, 35k IC,400, Main Lugs Only[Top Fed], Surface Mounted 2 400, Main Lugs Only 1 400, Through-Feed Lugs 6 25, 1P GHB Branch Breaker 6 1P GHQ Branch Provision Only 1 20, 3P GHB Branch Breaker 69 20, 1P GHQ Branch Breaker 2 Std. Bolted l Ground Bar (l/cu Cable) 2 Panel Nameplate - White with Black Letters - Screw on 2 Circuit Directory - Metal Frame with Plastic Cover 2 Type 1 Enclosure:EZB2060R 2 EZ Trim, Door in Door, Concealed Hardware:EZT2060S 1 COMPRESSION LUGS ON THRU FEED LUGS ONLY Designations: P1 1 Pow-R-Line1a Multi-Section Panel:2 Sections, 60 Circuits, 225, Fully Rated, 208Y/120V 3Ph 4W, luminum Bus, 18k IC,150, 3P EDB Main Breaker[Top Fed], Surface Mounted 1 225, Main Lugs Only 1 150, 3P EDB Main Breaker 1 225, Through-Feed Lugs 1 20, 2P QBHW Branch Breaker 4 30, 1P QBHW Branch Breaker 6 1P QBHW Branch Provision Only 3 15, 1P QBHW Branch Breaker 41 20, 1P QBHW Branch Breaker 1 25, 2P QBHW Branch Breaker 1 60, 2P QBHW Branch Breaker 2 Std. Bolted l Ground Bar (l/cu Cable) 2 Panel Nameplate - White with Black Letters - Screw on 2 Circuit Directory - Metal Frame with Plastic Cover 2 Type 1 Enclosure:EZB2048R 2 EZ Trim, Door in Door, Concealed Hardware:EZT2048S 1 COMPRESSION LUGS ON THRU FEED LUGS ONLY Designations: EP1

38 ETON Cutler Hammer Michael Mammone Phone: Neg# LT160914Y101 lt# 0005 Job Name: Burneson Middle School 13:15:33 Customer Bill of Material 1 Pow-R-Line3a 42 Circuits, 250, Fully Rated, 480Y/277V 3Ph 4W, luminum Bus, 50k IC,250, Main Lugs Only[Top Fed], Surface Mounted 1 250, Main Lugs Only 3 45, 3P HFD Branch Breaker 9 1P HFD Branch Provision Only 9 20, 1P HFD Branch Breaker 4 15, 3P HFD Branch Breaker 1 70, 3P HFD Branch Breaker 1 Std. Bolted l Ground Bar (l/cu Cable) 1 Panel Nameplate - White with Black Letters - Screw on 1 Circuit Directory - Metal Frame with Plastic Cover 1 Type 1 Enclosure:EZB2060R 1 EZ Trim, Door in Door, Concealed Hardware:EZT2060S Designations: EPDP 2 Pow-R-Line1a 30 Circuits, 100, Fully Rated, 208Y/120V 3Ph 4W, luminum Bus, 10k IC,60, 3P BB-H Main Breaker[Top Fed], Surface Mounted 1 60, 3P BB-H Main Breaker 1 30, 1P BB Branch Breaker 15 1P BB Branch Provision Only 14 20, 1P BB Branch Breaker 1 Std. Bolted l Ground Bar (l/cu Cable) 1 Panel Nameplate - White with Black Letters - Screw on 1 Circuit Directory - Metal Frame with Plastic Cover 1 Type 1 Enclosure:EZB2036R 1 EZ Trim, Door in Door, Concealed Hardware:EZT2036S Designations: EP2, EP3 1 Pow-R-Line3a 24 Circuits, 100, Fully Rated, 480Y/277V 3Ph 4W, luminum Bus, 35k IC,100, Main Lugs Only[Top Fed], Surface Mounted 1 100, Main Lugs Only 2 60, 3P FD Branch Breaker 6 1P FD Branch Provision Only 12 20, 1P FD Branch Breaker 1 Std. Bolted l Ground Bar (l/cu Cable) 1 Panel Nameplate - White with Black Letters - Screw on 1 Circuit Directory - Metal Frame with Plastic Cover 1 Type 1 Enclosure:EZB2048R 1 EZ Trim, Door in Door, Concealed Hardware:EZT2048S Designations: EL1

39 ETON Cutler Hammer Michael Mammone Phone: Neg# LT160914Y101 lt# 0005 Job Name: Burneson Middle School 13:15:33 Customer Bill of Material 2 Pow-R-Line2a 30 Circuits, 100, Fully Rated, 480Y/277V 3Ph 4W, luminum Bus, 14k IC,60, 3P GHB Main Breaker[Top Fed], Surface Mounted 1 60, 3P GHB Main Breaker 15 1P GHQ Branch Provision Only 15 20, 1P GHQ Branch Breaker 1 Std. Bolted l Ground Bar (l/cu Cable) 1 Panel Nameplate - White with Black Letters - Screw on 1 Circuit Directory - Metal Frame with Plastic Cover 1 Type 1 Enclosure:EZB2036R 1 EZ Trim, Door in Door, Concealed Hardware:EZT2036S Designations: EL2, EL3 1 Pow-R-Line1a Multi-Section Panel:2 Sections, 84 Circuits, 400, Fully Rated, 208Y/120V 3Ph 4W, Copper Bus, 18k IC,250, 3P DK Main Breaker[Top Fed], Surface Mounted, Surge Protective Device, 160 k SPD Series - Standard 1 400, Main Lugs Only 1 250, 3P DK Main Breaker 1 400, Through-Feed Lugs 1 30, 1P QBHW Branch Breaker 21 1P QBHW Branch Provision Only 62 20, 1P QBHW Branch Breaker 1 Surge Protective Device, 160 k SPD Series - Standard 2 Copper Main Bus, 400 mps 2 200% Rated Neutral (800) 2 Insulated / Isolated and Std Cu Ground Bar (Cu Cable Only) 2 Panel Nameplate - White with Black Letters - Screw on 2 Circuit Directory - Metal Frame with Plastic Cover 2 Type 1 Enclosure:EZB2090R 2 EZ Trim, Door in Door, Concealed Hardware:EZT2090S 1 COMPRESSION LUGS ON THRU FEED LUGS ONLY Designations: T3

40 ETON Cutler Hammer Michael Mammone Phone: Neg# LT160914Y101 lt# 0005 Job Name: Burneson Middle School 13:15:33 Customer Bill of Material 1 Pow-R-Line2a Multi-Section Panel:2 Sections, 84 Circuits, 400, Fully Rated, 208Y/120V 3Ph 4W, Copper Bus, 35k IC,400, Main Lugs Only[Top Fed], Surface Mounted, Surge Protective Device, 160 k SPD Series - Standard 2 400, Main Lugs Only 1 400, Through-Feed Lugs 78 20, 1P GHQ Branch Breaker 4 1P GHQ Branch Provision Only 2 30, 1P GHB Branch Breaker 1 Surge Protective Device, 160 k SPD Series - Standard 2 Copper Main Bus, 400 mps 2 200% Rated Neutral (800) 2 Insulated / Isolated and Std Cu Ground Bar (Cu Cable Only) 2 Panel Nameplate - White with Black Letters - Screw on 2 Circuit Directory - Metal Frame with Plastic Cover 2 Type 1 Enclosure:EZB2072R 2 EZ Trim, Door in Door, Concealed Hardware:EZT2072S 1 COMPRESSION LUGS ON THRU FEED LUGS ONLY Designations: T1 1 Pow-R-Line1a Multi-Section Panel:2 Sections, 84 Circuits, 400, Fully Rated, 208Y/120V 3Ph 4W, Copper Bus, 18k IC,250, 3P DK Main Breaker[Top Fed], Surface Mounted, Surge Protective Device, 160 k SPD Series - Standard 1 400, Main Lugs Only 1 250, 3P DK Main Breaker 1 400, Through-Feed Lugs 1 30, 1P QBHW Branch Breaker 21 1P QBHW Branch Provision Only 62 20, 1P QBHW Branch Breaker 1 Surge Protective Device, 160 k SPD Series - Standard 2 Copper Main Bus, 400 mps 2 200% Rated Neutral (800) 2 Insulated / Isolated and Std Cu Ground Bar (Cu Cable Only) 2 Panel Nameplate - White with Black Letters - Screw on 2 Circuit Directory - Metal Frame with Plastic Cover 2 Type 1 Enclosure:EZB2090R 2 EZ Trim, Door in Door, Concealed Hardware:EZT2090S 1 COMPRESSION LUGS ON THRU FEED LUGS ONLY Designations: T2

41 ETON Cutler Hammer Michael Mammone Phone: Neg# LT160914Y101 lt# 0005 Job Name: Burneson Middle School 13:15:33 Customer Bill of Material 1 Pow-R-Line2a 42 Circuits, 100, Fully Rated, 208Y/120V 3Ph 4W, Copper Bus, 35k IC,100, Main Lugs Only[Top Fed], Surface Mounted, Surge Protective Device, 160 k SPD Series - Standard 1 100, Main Lugs Only 12 1P GHQ Branch Provision Only 30 20, 1P GHQ Branch Breaker 1 Surge Protective Device, 160 k SPD Series - Standard 1 Copper Main Bus, 100 mps 1 200% Rated Neutral (225) 1 Insulated / Isolated and Std Cu Ground Bar (Cu Cable Only) 1 Panel Nameplate - White with Black Letters - Screw on 1 Circuit Directory - Metal Frame with Plastic Cover 1 Type 1 Enclosure:EZB2048R 1 EZ Trim, Door in Door, Concealed Hardware:EZT2048S Designations: T1B 1 Pow-R-Line1a 42 Circuits, 225, Fully Rated, 208Y/120V 3Ph 4W, luminum Bus, 22k IC,200, 3P EDB Main Breaker[Top Fed], 225, Through-Feed Lugs, Flush Mounted 1 200, 3P EDB Main Breaker 1 225, Through-Feed Lugs 1 20, 1P QBHW Branch Breaker, w/ Shunt Trip 2 40, 1P QBHW Branch Breaker 10 15, 1P QBHW Branch Breaker 7 1P QBHW Branch Provision Only 5 15, 1P QBHW Branch Breaker, w/ Shunt Trip 1 15, 3P QBHW-H Branch Breaker 2 15, 2P QBHW Branch Breaker 1 20, 2P QBHW Branch Breaker, w/ Shunt Trip 7 20, 1P QBHW Branch Breaker 1 Std. Bolted l Ground Bar (l/cu Cable) 1 Trim, LT Trim, 304 Brushed Stainless Steel 1 Panel Nameplate - White with Black Letters - Screw on 1 Circuit Directory - Metal Frame with Plastic Cover 1 Optional F Frame Terminal, (1) #6-300 kcmil 1 Type 1 Enclosure:YS LT Trim, 304 Brushed Stainless Steel:SS304 Trim 1 COMPRESSION LUGS ON THRU FEED LUGS ONLY Designations: KP1 (1)

42 ETON Cutler Hammer Michael Mammone Phone: Neg# LT160914Y101 lt# 0005 Job Name: Burneson Middle School 13:15:33 Customer Bill of Material 1 Pow-R-Line1a 42 Circuits, 400, Fully Rated, 208Y/120V 3Ph 4W, luminum Bus, 18k IC,400, Main Lugs Only[Bottom Fed], Surface Mounted 1 400, Main Lugs Only 1 15, 2P QBHW Branch Breaker 11 15, 1P QBHW Branch Breaker 8 1P QBHW Branch Provision Only 17 20, 1P QBHW Branch Breaker 4 20, 1P QBHW Branch Breaker, w/ Shunt Trip 1 Std. Bolted l Ground Bar (l/cu Cable) 1 Panel Nameplate - White with Black Letters - Screw on 1 Circuit Directory - Metal Frame with Plastic Cover 1 Type 1 Enclosure:EZB2090R 1 EZ Trim, Door in Door, Concealed Hardware:EZT2090S Designations: P3 (2) 1 Pow-R-Line1a 42 Circuits, 400, Fully Rated, 208Y/120V 3Ph 4W, luminum Bus, 18k IC,200, 3P JD Main Breaker[Top Fed], 400, Through-Feed Lugs, Surface Mounted 1 200, 3P JD Main Breaker 1 400, Through-Feed Lugs 4 25, 1P QBHW Branch Breaker 8 1P QBHW Branch Provision Only 20 20, 1P QBHW Branch Breaker 9 20, 1P QBHW Branch Breaker, w/ Shunt Trip 1 Std. Bolted l Ground Bar (l/cu Cable) 1 Panel Nameplate - White with Black Letters - Screw on 1 Circuit Directory - Metal Frame with Plastic Cover 1 Type 1 Enclosure:EZB2090R 1 EZ Trim, Door in Door, Concealed Hardware:EZT2090S 1 COMPRESSION LUGS ON THRU FEED LUGS ONLY Designations: P3 (1)

43 ETON Cutler Hammer Michael Mammone Phone: Neg# LT160914Y101 lt# 0005 Job Name: Burneson Middle School 13:15:33 Customer Bill of Material 1 Pow-R-Line1a 42 Circuits, 225, Fully Rated, 208Y/120V 3Ph 4W, luminum Bus, 22k IC,225, Main Lugs Only[Bottom Fed], Flush Mounted 1 225, Main Lugs Only 1 30, 2P QBHW Branch Breaker 3 15, 1P QBHW Branch Breaker 12 1P QBHW Branch Provision Only 1 20, 2P QBHW Branch Breaker 23 20, 1P QBHW Branch Breaker 1 Std. Bolted l Ground Bar (l/cu Cable) 1 Trim, LT Trim, 304 Brushed Stainless Steel 1 Panel Nameplate - White with Black Letters - Screw on 1 Circuit Directory - Metal Frame with Plastic Cover 1 Type 1 Enclosure:YS LT Trim, 304 Brushed Stainless Steel:SS304 Trim Designations: KP1 (2) 1 Pow-R-Line1a 42 Circuits, 225, Fully Rated, 208Y/120V 3Ph 4W, luminum Bus, 22k IC,225, Main Lugs Only[Bottom Fed], Surface Mounted 1 225, Main Lugs Only 5 20, 1P QBHW Branch Breaker, w/ Shunt Trip 1 15, 2P QBHW Branch Breaker 11 1P QBHW Branch Provision Only 8 15, 1P QBHW Branch Breaker 15 20, 1P QBHW Branch Breaker 1 Std. Bolted l Ground Bar (l/cu Cable) 1 Panel Nameplate - White with Black Letters - Screw on 1 Type 1 Enclosure:EZB2060R 1 EZ Trim, Door in Door, Concealed Hardware:EZT2060S Designations: P2 (2) ll orders must be released for manufacture within 90 days of date of order entry. If approval drawings are required, drawings must be returned approved for release within 60 days of mailing. If drawings are not returned accordingly, and/or if shipment is delayed for any reason, the price of the order will increase by 1.0% per month or fraction there of for the time the shipment is delayed.