Platypus. Pressure & Level Sensors & Transmitters

Transcription

1 Pressure & Level Sensors & Transmitters Platypus Heavy Duty SS Housing Ranges From 0-100mbar to 0-17 bar Ranges from 0-1M WG to M WG Made in Australia - Repairable Configured to suit your application Solid - Made from 316SS solid barstock Simple - Modular construction Reliable - Hundreds in use Fast Delivery - 1 to 3 days

2 Standard Version Immersible Version with nylon cable and SS support wire for use in reservoirs, dams, rivers or pits. Available with internal transmitter, or internal lightening protection and external DIN transmitter. Nylon cable should terminate in PL-TERM-SX/TE-E for optimum performance download selection form Platyus - standard version Standard Version Immersion & cable length to 100 metres 316SS - not suited to saline water Minimum span 0-1 M WG Threaded nose ½" BSP Dimensions on page 4 for salt water & chemicals - type HE Non Metal Version Immersible Version for saline water and other chemicals compatible with nylon, PVC and Buna N. Only available with 2 wire 4-20mA connection, utilises Gems 3100 Series transmitter internally with isolating diaphragm. Omit SS support wire in chemical solutions. download selection form Platyus - HE - plastic Ranges from 0-5 to metres IS transmitter EExia IIBT4 to ATEX - optimum Rugged PVC body & Buna N isolating diaphragm Pressure Transmitter Version with ½ BSP process connection and M12 4 pin IP65 connector and matching cable. This transmitter can be ranged to suit any application from mbar to 0-17 bar with 2 wire 4-20mA output. Wetted parts are 316SS and viton. The transmitter can be supplied with a vented extension cable in place of the connector - specifiy length with order. plug type Manifold Mount Version download selection form Platypus - plug connect ½ BSP ½" BSP parralel thread 316SS - not suited to saline water 2 wire 4-20mA Zero & span coarse & fine adjustments

3 Level Transmitter where the flexible nylon tube is replaced by 8mm 316SS tubing. This allows rigid location in tanks through most tank entries including flanges. If used without electronics internally it can tolerate process temperatures to 80 C. Simply assembled with swagelock fittings the tube can be terminated in a standard thermocouple head with terminal block. Tube Mount Version Common Specifications Calibrated ranges from 1M to 170mWG Extremely rugged 316SS or PVC body Configurations to suit most applications Readily repairable at low cost Sensor & system lightning protection option Low operating voltage Internal SMD transmitter option Accuracy better than 0.5% (system) Submersible to 100m (appropriate versions) download selection form Platypus - rigid SS tube build Sensor Output: Range: Accuracy: Construction: Power supply: Range: Accuracy: Construction: 100mV at 1mA excitation 0.4, 2, 7, & 17.2 bar 2% 316SS diaphragm 18mm dia. Internal Transmitter - TX 7-35V DC 10mV to 100mV link selectable 0.2% SMD Lightning Protection - LP to AS Cat.B On 4 wire versions, the internal LP option protects the sensor & is fitted in the housing (cannot use with internal TX) Accessories Vented Terminal Box DIN Rail SG Transmitter Lightning Protection for 2 Wire Loops to AS 1768 Cat.B PL-TERM-SX/TX-E PL- TX-DIN PL-ELP Terminals for exterior cables Molecular filter eliminates condensation TX version encloses PL-TX-DIN Lightning earth stud for LP system Order a Platypus to Your Own Specification Sensor Styles PLATPUS-SG 4 wire basic PLATYPUS-LP 4 wire, internal LP PLATYPUS-TX 2 wire, internal TX PLATYPUS-TXP 2 wire, plug version PLATYPUS-HE 2 wire, non-metal version 2 wire output - 4 wire input supply V DC (lightning protection on output) Rangeable by dip switch 5 mv mv Size 22.5 x 76 x 110mm Cable Styles Standard Platypus includes a 10M nylon tube type cable. Longer cables are available in 1M increments. Some versions available with 6 core vented cable To protect a long 4-20mA loop the PLATYPUS-ELP is used (this device is built into PL-TX-DIN as standard). It should be fitted adjacent to the devive it is protecting & one would be fitted at each end of a vulnerable loop, unless one end was PL-TX-DIN Interface Devices PL-TX-DIN 2 wire standard TX with loop power & LP on output PL-TERM-SG/TX-E Standard terminal box with vent PL-ELP DIN rail loop lightning protection (2 wire)

4 Lightning Protection - Internal Dimensions - Standard Body Delrin nose cover supplied standard Tested to AS1768 Cat B 3000 amps, 3000 volts 8/20μS Designed to protect system components Internal PCB to protect sensor DIN protector for two wire loops Fitted standard to PL-TX-DIN ½" BSP male parallel width 23mm Ø 8mm nylon Ø 32mm 165mm 192mm Platypus - HE-KIT PR-4114 universal transmitter and PR-4501 programmer Loop power supply & output scaling. 2250V AC isolation PLATYPUS-HE Economy version 0-1 to M WG The Platypus-HE-KIT combines three fabulous products from ECEFast. The PR-4114 Universal Transmitter with 2250V isolation, Gems 3100 pressure transmitter and Platypus HE. Result - more performance per dollar than from any competitor V AC/DC DIN rail module power supply/interface 2250V isolated - 3 ways - input/supply/output 4-20mA or voltage output - fully scaleable Digital display/ self diagnostics Clip on programmer - password protected Supplied without SS support wire download selection form Platypus - HE-KIT

5 Level Stick - Non Metal Vented extension cable - 10M incl. (specifiy extra) Cleaning solution incl. Solvent cement incl. Lightning protection - optional Silica gel incl. Body 32mm pressure rated PVC pipe (local purchase in lengths to 6M 4-20mA Rigid Assemble On Site Flush Diaphragm for Contaminated Liquid Lengths to 0-6 M - output scaled 4-20mA = M WG Sensor accuracy 0.25% - uncalibrated accuracy ± 1% ( output 4-20mA) Power supply V DC 32mm PVC pipe available in any hardware Cut to length & assemble on site - no solder Isolating flush Buna N diaphragm Wetted parts - PVC, Buna N, Nitrile (or Viton) Description Assemble bottom using solvent cement. Insert silica gel into tube. Assemble top using solvent cement - push & twist. Tighten cable gland. Level stick is a low cost continuous transmitter for level measurement in highly contaminated liquids and slurries including raw sewerage. All wetted parts are non metallic and resist organic and many inorganic chemicals at low temperatures. It is shipped in a standard air satchel and assembled on site with simple tools & familiar processes. Options Bottom assembly supplied fully assembled Vented terminal box - for tropical or very wet environments to terminate vented cable. Internal 4-20/4-20mA lightning protection device - pre wired (if ordered with level stick) sales@ecefast.com.au