Electronic Fuel Injection Made Simple:
|
|
- Austin Phillips
- 6 years ago
- Views:
Transcription
1 The 09 Harley- Davidson FLHTC Electra Glide Classic on the lift awaiting an ECM transplant We removed the seat and side covers. On the left side, the fuse panel cover was popped off. To cut power to the engine control module (ECM), the corresponding fuse needed to be removed its location is identified on the cover. 03 The ECM fuse was removed next by carefully gripping the fuse by hand and gently pulling it straight out. Electronic Fuel Injection Made Simple: Each of the stock, narrow band oxygen (O2) sensors had to be removed from each header pipe. An O2 sensor socket that slips over the wiring loom or a crow s foot extension make this job easier. On 09 and earlier models, the O2 sensors are at the top of each pipe close to the head. If the sensors have been in for a while adding a few drops of throttle body choke and carb cleaner to loosen them up. We used a crow s foot attached to a 3/8-socket extension to remove the sensors. 06 A close-up of the stock, narrow-band O2 sensor. ThunderMax: EFI Tuning as You Ride Words: Toph Bocchiaro and Rogue Photos: Rogue Since electronic fuel injection (EFI) appeared on Harley-Davidson baggers in 1995, for many of us, the thought of a computer replacing the carburetor s gas and air mixing duties has been a difficult proposition. The Harley faithful were leery of the electronic technology that replaced the venerable, easy-to-tune carburetor. As most of us know the hog-riding public, as well as the Factory, don t always make hasty, potentially disastrous decisions. There s a century s worth of Harley products and tradition and it would be fair to say Harley isn t much of a follower. Based on history, we riders love that approach. We embrace retro, whether it s looks or choosing aircooled, pushrod motors. However, the Motor Company, always looking further down the road than just the next model year, saw the writing on the wall. In order to comply with ever-tightening emissions standards and future environmental concerns, EFI was more than just an exercise in what if engineering and an option to check on bike orders. Carbs worked pretty well for close to a century, and the straightforward accessibility and diagnosis of fuel-related problems was well within the reach of the average mechanic. If any of us want a non-efi bagger, H-D s last carbed Touring bikes rolled out of York, Pennsylvania, for the 06 model year. Luckily though, the EFI system has been continuously refined over the years and the newest Electronic Sequential Port Fuel Injection (ESPFI) system is reliable and dare we say it better than any carb ever made for the precise regulation of fuel delivery. Unlike a carburetor s sole responsibility of passing gas and air into the motor, EFI is a part of a complete, computer operated engine management system. A carb is a passive device in that it operates (discharges gas into the manifold) only when a pressure difference exists between the carb s gravity fed float bowl and the engine. As the piston moves down the cylinder a vacuum is created and that pressure difference draws air into the carburetor. Air speed increases as it passes through the carb (venturi effect) and gasoline is drawn through the carb s jets, mixing with and forming a fine mist (atomization) with the incoming air, eventually reaching the spark plug in the cylinder head and combustion occurs. A throttle cable opens the throttle plate (butterfly) and allows more air to pass into the carb. The farther you twist the throttle the clearer the path for air to flow in. A downside to this simplicity is that carbs are sensitive to weather related air pressure and altitude changes. A carb tuned at sea level would run rich if ridden at significant elevation with a noticeable loss of performance. If going from high to low elevation the fuel mixture would get lean, a potentially engine threatening situation. Obviously a simplistic explanation, but even the most sophisticated carbs operate on the same principles. EFI s main difference is that instead of low pressure induced airflow to draw and atomize the fuel, the gas is actively sprayed through injectors directly into the intake manifold. The basics of how it works on a H-D is the fuel pump located in the fuel tank supplies high-pressure (55-62 PSI) fuel to a fuel rail on the throttle body (induction module assembly connected to the cylinder heads). The fuel rail feeds fuel to the injectors, which spray fuel into the intake tract. One injector is located close to each cylinder head intake port. In addition to the throttle body and injectors, the electronic control module (ECM, the bike s brain) uses multiple sensors to gather information about engine operating conditions, air temperature and manifold pressure. The ECM then uses a program (AKA, calibration map) to determine the timing and amount of fuel delivery to each injector. 62 January 2012 January
2 07 The threads on the new ThunderMax wideband O2 sensors were dabbed with anti-seize compound to prevent corrosion between the sensors and pipes. 09 The front sensor wires were routed across the brace in front of the engine and along the lower frame rail on the right side of the motorcycle and connected to the autotune harness plug. 08 The wideband sensors were installed into each pipe. 10 The rear lead was routed between the transmission top cover and the starter then beneath the ABS caddy (under the right side cover) and connected to autotune harness Of note, is the ECM is also responsible for ignition timing. A butterfly is still present to control airflow into the intake, and through 2007 was controlled by throttle cables. For 2008, H-D eliminated throttle cables and introduced electronic throttle control (throttle-by-wire; fly-by-wire). Sensors inside the right grip communicate throttle position to the ECM, and based on the map, RPM, and engine load the proper amount of fuel and air are delivered to the throttle body. A motor opens and closes the butterfly to control airflow. The ECM is simultaneously controlling ignition timing as well. Although we won t delve into every aspect of how the ECM gathers and uses information, there have been two general ways EFI does its job, and Harley has used both methods. Through 2001, the Magneti-Marelli (MM) produced EFI is what s called an Alpha-N based EFI. Throttle position and RPM determined the amount of fuel to deliver. Harley also added an intake air temperature (IAT) sensor within the throttle body to make adjustments to the fuel mixture. A problem with the sensor in the MM system was that the measured air temperature was not an accurate reading of what the intake temp really was. Relying on temperature close to a hot motor was not the best way to determine intake air temp. When the air enters the venturi of the throttle body, it speeds up, thereby changing its temperature. In addition, the throttle body sits right above the hot motor, compounding the problem of accurate air temperature measurement. Some of the problems reported with the MM EFI were hard starting, erratic idle, and difficulty in tuning. For performance motors, the dual-plenum throttle body, with independent runners feeding each cylinder, was too small to pass the required air into the engine. An advantage of throttle-based control is that there s no dependence on intake-manifold pressure, which benefits motors with radical cams. The next generation Delphi manufactured EFI uses a speed-density method to calculate how much fuel the 64 January 2012
3 motor needs. Speed-density systems use RPM and manifold pressure (via a MAP sensor in the intake manifold/ throttle body) to determine the load on the motor and report back to the ECM for fuel changes. Again, H-D incorporated intake temperature but accuracy was improved by moving the sensor into the throttle body. In summary and very generally, from H-D EFI used a throttleposition based system and from 02 to now a manifold-pressure based EFI. There are two other important EFI operating methods: an open loop and closed loop. In open loop ( 95-06) the ECM uses preprogrammed maps to control EFI. Sensor data is read by the ECM and then matched to a map/table/ database; the maps have instructions for the amount of time an injector is on as well as ignition timing. Since the maps are fixed (read only in computer terms) even small changes to airflow (pipes, airbox) require reprogramming the map and often requiring expensive dyno tuning. A closed loop system has preprogrammed maps but can be modified (read/write). Oxygen (O2) sensors located in the exhaust pipes continuously monitor the spent gas to determine and maintain the proper air:fuel ratio and ignition timing on the fly in real time. For the O2 sensors were located close to the cylinder head; the sensors needed the heat to operate correctly. For 10 smaller, heated O2 sensors were used and located before the catalytic converter, under the transmission area. The heated sensors control emissions better when the engine is cold. Small changes in airflow or even poor gasoline quality can be overcome by the ECM but due largely to environmental concerns, air:fuel ratios are varied within a small range due to the stock narrow band O2 sensors. What narrow really means is the measurement range is small and the sensors don t work well with performance modifications. For government compliance the air:fuel ratios fall more on the lean side. Leaner mixtures (larger A:F) get better fuel economy, have more complete combustion (clean burning) for better emissions and fuel economy, but generate excess heat. Richer mixtures have the opposite characteristics while delivering maximum power. A closed loop system can be remapped as well as using add-on modules to modify air:fuel that work in conjunction with the factory ECM in the same way as open loop; tuning will still be 11 The factory O2 sensor to ECM connectors were capped off and not used. 12 Next, the factory ECM was removed by spreading the plastic latches on either side of it and lifting up and to the right to release it. 66 January 2012 January
4 limited by the narrow band O2 sensors. While adding aftermarket wideband oxygen sensors allows a wider range of air:fuel monitoring, the stock ECM 13 will still need remapping for changes in engine airflow, and for optimal performance require expensive and time consuming dyno tuning. Be extremely To release the main wiring harness from the ECM the release button (top arrow) was pressed and the grey locking bar moved to the full rearward position until the bar locked into the rear detent (bottom arrow). Care must be taken to make sure the bar is in the full rearward position to release the connector s internal latches; then we removed the connector from the ECM. careful when choosing a dyno tuning technician; treat the situation like real surgery. Because of the relative complexity of EFI there are many hacks that 14 The main harness connector was cleaned and the rubber gasket (arrow) checked for damage then coated in dielectric grease. We routed the autotune harness plug up the seat post past the battery towards the ECM holder. capitalize on misinformed customers. It s very easy for a tech with little experience to make your bike run terribly, then sell you more parts to try and fix what he messed up. It s easy to get fooled into the next, best, black box, so do your homework and make sure you have referrals. It can get very expensive when your bike doesn t run right. If you plan on any engine modifications try and have a plan and do the mods all at once if possible. That way each time one part is changed pipes, airbox, cams, headwork, big bore kit, etc. you won t need to get a dyno tune. Another option that largely avoids dyno tuning is the addition of a new ECM that is easily modified and can handle a wide range of performance upgrades. There are several on the market that after engine modifications can tune the EFI and ignition just by riding the bike. Ranges of tuning after performance modification vary by manufacturer but they all provide more and better control over the fuel and ignition system. They re not for everyone, but if optimal tune and avoiding a lot of dyno time is your goal there is an option. One such device is the ThunderMax ECM with integrated AutoTune that works in conjunction with two wideband oxygen sensors. Using either a stock or aftermarket throttle body the closed-loop system automatically adjusts fuel and ignition requirements due to performance upgrades such as pipes, airbox, and cams. ThunderMax can also add this same closed loop operation on your older Magneti-Marelli or Delphi systems. ThunderMax works with either throttle-by-wire or cableoperated throttle bodies. The ThunderMax wideband, fivewire oxygen sensors thread into bungs 15 The autotune harness plugged into the ThunderMax (arrow) with the logo facing up and secured with the two screws. Before plugging in the ThunderMax unit we confirmed the gasket was fully seated in the connector, and the locking bar was all the way open. To avoid damage to the ThunderMax it s important everything slides into place smoothly and that it is all the way in before engaging the locking bar. The ECM fuse got a dab of dielectric grease and plugged back in. 68 January 2012 January
5 Metal 16 We fired up a laptop computer and launched the previously installed ThunderMax software. Step-by-step installation instructions were easy to follow. We had previously downloaded a base map based on our engine configuration. The program gave us different map options and we picked the one that was closest to our setup. 17 We connected the supplied communication cable between the computer s USB port and the ThunderMax dataport (arrow; under the protective plug) to allow for information transfer. located near the exhaust port, and are the same thread size and location as stock narrow band sensors used on 08 and 09 exhausts. For 10-12, smaller oxygen sensors were used and located forward of the catalytic converter near the transmission. The ThunderMax sensors must be mounted in the location and on newer machines either new bungs will need to be added to the existing headers in the upper location (with the lower stock sensors removed and ports capped) or ideally order an exhaust system for a 2009 model (fitment is the same for models) and the ThunderMax sensors will install without modification. ThunderMax has all the info needed and detailed instructions and support. To get a better look at the system and try it we ordered a ThunderMax TBW (PN ) for throttleby-wire H-D Touring models. The system includes a ThunderMax TBW ECM with integrated autotune module, two wideband oxygen sensors, USB communication cable, TMax tuner software, and ThunderMax TBW quick start guide. We recently installed a ThunderMax ECM with an autotune module on a 96ci Twin Cam that had only airbox and pipe modifications. The bike ran well beforehand but afterwards the owner said he couldn t believe it was the same bike. He reported a super-snappy throttle response and a cooler running motor, and while there was no dyno chart (he didn t need to pay for one) he said the bike had much more seat of the pants torque. B source Zippers Performance Products (410) Thunder-Max.com THE FIRST START After a new module install or interruption of 12-volt power takes place perform the following procedures: Turn the ignition switch on and the handlebar switch to run for at least 20 seconds Cycle the ignition switch off and on and start the engine Let the motorcycle idle on its own for at least 15 seconds Turn off the ignition and then restart the motorcycle. Normal idle speed should be attained depending on engine temperature. The warm-up cycle will have slightly higher idle speed until it reaches operating temperature. 70 January 2012
Motorcycle Carburetor Theory 101
Motorcycle Carburetor Theory 101 Motorcycle carburetors look very complex, but with a little theory, you can tune your bike for maximum performance. All carburetors work under the basic principle of atmospheric
More informationIT S ELECTRIC SWITCHING TO HOLLEY EFI YIELDS BETTER DRIVABILITY AND MORE POWER FOR A BOOSTED 68 FIREBIRD
WORDS: Scott Parker PICTURES: By Redline Motorsports IT S ELECTRIC SWITCHING TO HOLLEY EFI YIELDS BETTER DRIVABILITY AND MORE POWER FOR A BOOSTED 68 FIREBIRD I t s been said many times, and often it has
More informationHSR Carburetor Easy Kits Installation Instructions For Evo Big Twin Kit: # 42-7 Twin Cam Kit: # 42-18
HSR Carburetor Easy Kits Installation Instructions For Evo Big Twin Kit: # 42-7 Twin Cam Kit: # 42-18 Revised 5/01/01 EK-1 Easy Kit Installation Instructions The HSR series carburetors are precise yet
More informationHSR Carburetor. Total Kits. Installation Instructions. # Evo Big Twin # present Twin Cam
HSR Carburetor Total Kits Installation Instructions HSR42 Kits: HSR45 Kits: #42-8 84-99 Evo Big Twin #42-19 99 - present Twin Cam #45-2 84-99 Evo Big Twin #45-3 84-99 Evo Big Twin #45-4 99 - present Twin
More informationKEIHIN CARBURATORS FOR 4-CYLINDER HONDA MOTORCYCLES
KEIHIN CARBURATORS FOR 4-CYLINDER HONDA MOTORCYCLES Set of 4 Keihin carburetors marked 089A and used on 1976 CB550K GENERAL NOTES: All carburetors perform the same function: mixing air and fuel for supply
More informationTOURING Models
P/N FI-1252HPST Patent Numbers: 7,000,599 & 7,124,742 Electronic Jet Kit Instructions Thank you for choosing the Techlusion Electronic Jet Kit, the TFI. This TFI model is ONLY usable for the following
More informationVacuum Readings for Tuning and Diagnosis
Vacuum Readings for Tuning and Diagnosis -Henry P. Olsen Once you learn to properly interpret its readings, a vacuum gauge can be one of the most useful tools in your toolbox. 22 FEATURE Some people consider
More informationThank you for choosing the Techlusion Electronic Jet Kit, the TFI. The TFI is usable for sequential fuel injection 2 cylinder Suzuki motorcycles **.
Rev 1.1.1 2055ST TFI TFI Patent Numbers: 7,000,599 & 7,124,742 TFI Instructions Suzuki Thank you for choosing the Techlusion Electronic Jet Kit, the TFI. The TFI is usable for sequential fuel injection
More informationThe All-New BIG97 Tri-Power. In Detail.
The All-New BIG97 Tri-Power. In Detail. The all-new Stromberg BIG97. On the outside, it s Genuine 97 all the way. But on the inside, we re talking 250cfm, new improved fuel circuits, ported distributor
More informationNew! Video Instructions Now Available on You Tube Smart Phone Users See Back Page
New! Video Instructions Now Available on You Tube Smart Phone Users See Back Page Part # 309-380, 2012 Softail / Dyna Thank you for purchasing a ThunderMax ECM! Please read through the following instructions
More informationSerial # TMTM. # , 2014 Touring & Trike Models. New! Video Instructions Now Available on You Tube Smart Phone Users See Back Page
New! Video Instructions Now Available on You Tube Smart Phone Users See Back Page #309-562, 2014 Touring & Trike Models Thank you for purchasing a ThunderMax ECM! Please read through the following instructions
More informationSherco Carb Jetting Instructions
Sherco Carb Jetting Instructions This manual provides instructions on how to remove and reinstall the stock carburetor, it also shows you how to change the pilot jet and the main jet. It is intended to
More informationTUNING Training Course Material 2014 Valid for Diag4Bike V14 only On-line Multimedia User Manual is under preparation.
TUNING Training Course Material 2014 Valid for Diag4Bike V14 only On-line Multimedia User Manual is under preparation www.diag4bike.eu 1 TUNING STRATEGY Tuning system is based on DIAG4BIKE diagnostics
More informationHSR Carburetor. Total Kits. Installation Instructions. # Evo Big Twin # present Twin Cam
HSR Carburetor Total Kits Installation Instructions HSR42 Kits: HSR45 Kits: #42-8 84-99 Evo Big Twin #42-19 99 - present Twin Cam #45-2 84-99 Evo Big Twin #45-3 84-99 Evo Big Twin #45-4 99 - present Twin
More informationHarley Davidson V-Rod Models
2801190 REV. 8-11-05 User Manual 2002-2005 Harley Davidson V-Rod Models Part Number DFCH-5 Congratulations on your purchase of this Dynatek product. Please take a moment to read these instructions completely
More informationINSIDE YOUR HOLLEY CARBURETOR FUEL INLET SYSTEM
INSIDE YOUR HOLLEY CARBURETOR The carburetor is quite simply a fuel metering device that operates under the logical and straightforward laws of physics. It has evolved over the years from a very simple
More informationPart # ,73 for Big Twin Models
Part # 309-370,73 for Big Twin Models Thank you for purchasing a ThunderMax 50 ECM! Please read through the following instructions before beginning the installation procedure. Following these instructions
More informationQUICK FUEL TECHNOLOGY HOT ROD SERIES CARBURETORS SLAYER SERIES CARBURETORS SUPER STREET SERIES CARBURETORS
QUICK FUEL TECHNOLOGY Installation Instructions HOT ROD SERIES CARBURETORS SLAYER SERIES CARBURETORS SUPER STREET SERIES CARBURETORS HR-580-VS 580 CFM Vac. Secondary!!! SS-680-VS 680 CFM Vac. Secondary
More informationChapter 4 Part D: Fuel and exhaust systems - Magneti Marelli injection
4D 1 Chapter 4 Part D: Fuel and exhaust systems - Magneti Marelli injection Contents Accelerator cable - removal and..................... 11 Air cleaner element - renewal..............................
More informationNew! Video Instructions Now Available on You Tube Smart Phone Users See Back Page
New! Video Instructions Now Available on You Tube Smart Phone Users See Back Page Installation / Setup Guide Please Note: This product is Legal in California only for racing vehicles which may never be
More informationDirect Link Basic Tuning Guide (Delphi)
Direct Link Basic Tuning Guide (Delphi) This Guide is intended to answer basic Direct Link tuning questions and to act as a Quick Start Guide. It is not intended to be the Gospel on the tuning process
More informationHW Prowler Carburetor Installation Instructions
HW Prowler Carburetor Installation Instructions Page 1 of 6 Carb Kit Contains: HW modified Mikuni 36mm pumper style carb Custom choke cable Fuel Line Clamp Instructions (2) Leaner and (2) richer main jets
More informationPart # for V-Rod Models MODELS
Installation / Setup Guide P lease Note: This product is Legal in California o nly for racing vehicles which may never be used upon a highway. The user shall determine suitability of the product for his
More informationA Simple View of Fuel Injection
A Simple View of Fuel Injection Your engine is an air pump, the more air you pump through it, the more power you make. Figure 1 Any internal combustion engine will flow air at a rate determined by many
More information3. At sea level, the atmosphere exerts psi of pressure on everything.
41 Chapter Gasoline Injection Fundamentals Name Instructor Date Score Objective: After studying this chapter, you will be able to explain the construction, operation, and classifications of modern gasoline
More informationOGO-MAP/MAF User Manual
OGO-MAP/MAF User Manual 1 OGO Dual Mode MAP/MAF Sensor Enhancer Ready to Install This Map Sensor Enhancer was built directly from the OGO specifications manual. It has separate Hwy & City adjustments along
More informationMAXI-BORE TM CARBURETTORS
MAXI-BORE TM CARBURETTORS 26mm/28mm Mik bored to 30.5mm 33mm Smoothbores bored to 38.5mm Don t just rebuild your carbs MAXI-BORE TM them! MAXI-BORE TM carbs are more than just cleaned, rebuilt, or bored,
More informationElectronic Jet Kit Instructions
MFG P/N FI-1049ST Patent Number: 7,000,599 & 7,124,742 Electronic Jet Kit Instructions Thank you for choosing the Techlusion Electronic Jet Kit, the TFI. This TFI is usable for the following models: Polaris
More informationCAUTION: CAREFULLY READ INSTRUCTIONS BEFORE PROCEEDING
Twin Tec Installation Instructions for Wide-Band Exhaust Gas Oxygen Sensor System CAUTION: CAREFULLY READ INSTRUCTIONS BEFORE PROCEEDING OVERVIEW The is a complete air/fuel ratio (AFR) metering system
More information2009 Yamaha Apex Snowmobile
PARTS LIST 2009 Yamaha Apex Snowmobile Installation Instructions quantity description 1 power commander 1 USB cable 1 cd-rom 1 installation guide 2 power commander decals 2 dynojet decals 2 velcro strip
More informationTHE IDIOT S GUIDE TO TUNING SU CARBURETTERS
THE IDIOT S GUIDE TO TUNING SU CARBURETTERS There are four distinct phases to tuning SU carburetters (carbies). The first is to set the fuel level in the float bowl, the second is to centre the needle
More informationApplication(s) > Items Supplied > Instruction Manual >
301 E. La Palma Ave., Yorba Linda, Ca 97 Ph. 714.69.10, Fax. 714.69.5016 Items Supplied > Application(s) > www.fi000r.com 1 Fi000R Fuel Injection Module Zip Ties 1 Velcro Strip Oxygen Sensor Eliminators
More informationMGB FUEL INJECTION. Modernizing a great ride - And the unwillingness to finish and drive
MGB FUEL INJECTION Modernizing a great ride - And the unwillingness to finish and drive COUNTER POINT Earlier MGs had twin SU style carburetors. By 1975 these were dropped in a desperate attempt to complying
More informationДнепр) Russian Motorcycle Carburetors Part 2B: PZ-24 and PZ-28 Carburetor Assembly and Jet Drilling
Ural (Урал( Урал) - Dnepr (Днепр( Днепр) Russian Motorcycle Carburetors Part 2B: PZ-24 and PZ-28 Carburetor Assembly and Jet Drilling (applies also to K-37 K and K-38 K carbs) Ernie Franke eafranke@tampabay.rr.com
More informationPart #82064 Add-A-Stage EFI Nitrous System
1 INSTRUCTIONS Part #82064 Add-A-Stage EFI Nitrous System Thank you for choosing products; we are proud to be your manufacturer of choice. Please read this instruction sheet carefully before beginning
More informationINSTALLATION TRUE DUAL HEADPIPES 497
TRUE DUAL HEADPIPES 497 PARTS INCLUDED 1 Front Head Pipe 1 Rear Head Pipe 1 Front Heat Shield 1 Rear Heat Shield 1 Bracket (stamped 422-P) 1 Bracket (stamped 423-P) 2 1/2 x 1-1/4 Socket Head Cap Screw
More informationPart # for Sportster Models
Part # 309-365 for Sportster Models Thank you for purchasing a ThunderMax ECM! Please read through the following instructions before beginning the installation procedure. Following these instructions will
More informationTHE CARBURETOR: THE ADDITIONAL SYSTEMS
THE CARBURETOR: THE ADDITIONAL SYSTEMS From the acceleration pump to the power jet: the special configuration of circuits that apply to some carburetor models As stated in the previous article, a carburetor
More information2011 Yamaha Apex Snowmobile
PARTS LIST 2011 Yamaha Apex Snowmobile Installation Instructions quantity description 1 power commander 1 USB cable 1 cd-rom 1 installation guide 2 power commander decals 2 dynojet decals 2 velcro strip
More informationElectronic Jet Kit Instructions
Ver. 1.01 KFX 450 TFI-6040ST Thank you for choosing the Techlusion Electronic Jet Kit for your KFX 450, the TFI. The TFI is usable only for the following models: Kawasaki KFX 450 Thank you for choosing
More informationTuning A Walbro Carb. Walbro Carb TUNE UP & Illustrated Guide
Tuning A Walbro Carb Walbro Carb TUNE UP & Illustrated Guide by M. B. Fuess Walbro carbs aren t too difficult to tune up if you know what you re doing. First of all, you need to know how the carb works
More informationExhaust Gas CO vs A/F Ratio
Title: Tuning an LPG Engine using 2-gas and 4-gas analyzers CO for Air/Fuel Ratio, and HC for Combustion Efficiency- Comparison to Lambda & Combustion Efficiency Number: 18 File:S:\Bridge_Analyzers\Customer_Service_Documentation\White_Papers\18_CO
More informationInnovative Racing Electronics
FOR IMMEDIATE RELEASE Contact: Dan Rudd Phone: 407.330.9727 FAX: 407.322.8632 E-Mail: sales@mpsracing.com Web: www.mpsracing.com Holley Commander 950 Universal 4 Cylinder Fuel Injection Kit Sanford, Florida,
More informationTable of Contents. Introduction Features of the UEGO UEGO 2000 Components 1. Installation Wideband Oxygen Sensor 2 Driver Box 2 Display Head 4
Table of Contents Introduction Features of the UEGO 2000 1 UEGO 2000 Components 1 Installation Wideband Oxygen Sensor 2 Driver Box 2 Display Head 4 Display Head Operation Description 5 Display Mode 5 Playback
More informationTroubleshooting A Vintage Distributor Ignition System
Troubleshooting A Vintage Distributor Ignition System -Henry P. Olsen When the owners of vintage carburetor- and distributor-equipped vehicles see that a shop has a big-box engine analyzer, they believe
More informationInnovative Racing Electronics
MPS Fast FI Mixture Control Installation Instructions The MPS Fast FI Mixture Control P/N 1-0337 is a simple means to adjust the fuel curves on your fuel-injected motorcycle. This allows for tuning after
More informationUse these modules to gain valuable knowledge about STIHL policies, procedures and products that will be a benefit to you on the job immediately.
Bronze Level Training Lesson 09 This is Bronze Level 09 of 10. Welcome to the Service Advantage Bronze Level Training on icademy. These modules are designed to enhance your knowledge base on topics such
More informationREFERENCE MATERIAL: PROGRAM CODE - undefined
REFERENCE MATERIAL: PROGRAM CODE - undefined - Revised 2001-2001 by Harley-Davidson Motor Company - All Rights reserved General Operating Parameters for Open and Closed Loop Running How does the Buell
More informationCMP Turbo Kit Installation Instructions Touring Models
CMP Turbo Kit Installation Instructions 2008-2014 Touring Models Bike Prep Drain engine oil into a clean pan and inspect oil for contaminant. Any debris going through the motor will end up in the turbo,
More informationCRUSHER TRUE DUAL HEADPIPES 513
CRUSHER TRUE DUAL HEADPIPES 513 THANK YOU FOR CHOOSING CRUSHER! PROTECT YOURSELF AND OTHERS FROM POTENTIAL INJURY AND PROPERTY DAMAGE OR LOSS. PAY CLOSE ATTENTION TO ALL INSTRUCTIONS, WARNINGS, CAUTIONS,
More informationFUEL INJECTION SYSTEM - MULTI-POINT
FUEL INJECTION SYSTEM - MULTI-POINT 1988 Jeep Cherokee 1988 Electronic Fuel Injection JEEP MULTI-POINT 4.0L Cherokee, Comanche, Wagoneer DESCRIPTION The Multi-Point Electronic Fuel Injection (EFI) system
More informationPLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
PARTS LIST 2014 Harley Davidson Sportster 1200 Installation Instructions 1 Power Commander 1 USB Cable 1 Installation Guide 2 Power Commander Decals 2 Dynojet Decals 2 Velcro strips 1 Alcohol swab 2 O2
More informationUser s Guide For Control Pressure Gauge
User s Guide For Note: The fuel system should be under pressure even when the car is off. ALWAYS follow these precautions: 1. Always wear safety glasses. 2. When the fuel lines are first loosened about
More informationCAUTION: CAREFULLY READ INSTRUCTIONS BEFORE PROCEEDING
Daytona Sensors LLC Engine Controls and Instrumentation Systems Installation Instructions for Wide-Band Exhaust Gas Oxygen Sensor Interface CAUTION: CAREFULLY READ INSTRUCTIONS BEFORE PROCEEDING OVERVIEW
More informationElectronic Jet Kit Instructions
Rev 1.0.3 FI-1040ST Electronic Jet Kit Instructions Thank you for choosing the Techlusion Electronic Jet Kit, the TFI. The TFI is usable for both early and late model fuel injected Harley Davidson s. This
More informationHOWELL INSTALLATION MANUAL. Throttle Body Fuel Injection Harness
HOWELL ENGINE DEVELOPMENTS, INC. FUEL INJECTION APPLICATIONS INSTALLATION MANUAL Throttle Body Fuel Injection Harness Howell Engine Developments, Inc. 6201 Industrial Way Marine City, MI 48039 Phone: 810-765-5100
More informationWILD THINGS FUEL INJECTION CONTROLLER 9219
I N S TA L L AT I O N WILD THINGS FUEL INJECTION CONTROLLER 9219 BY D O B E C K P E R F O R M A N C E FITS: 06-UP SOFTAIL, DRESSER, AND ROAD KING WITH DELPHI FUEL INJECTION Thank you for choosing the Wild
More informationINTRODUCTION. Figure 1 INSTALLATION. Checking the Baseline Adjustments
INSTRUCTION MANUAL INTRODUCTION Demon Carburetors have many unique features that make them the ultimate choice for racers, like yourself. Whether it is street / strip performance, or just getting the most
More informationHonda Accord/Prelude
Honda Accord/Prelude 1984-1995 In Tank Fuel Pumps TEST 1. Turn the ignition OFF. 2. On the Accord, remove the screws securing the underdash fuse box to its mount. Remove the fuel cut off relay from the
More informationCAUTION: CAREFULLY READ INSTRUCTIONS BEFORE PROCEEDING
Daytona Sensors LLC Engine Controls and Instrumentation Systems Installation Instructions for Wide-Band Exhaust Gas Oxygen Sensor Interface CAUTION: CAREFULLY READ INSTRUCTIONS BEFORE PROCEEDING OVERVIEW
More informationPLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
PARTS LIST FUEL AND IGNITION 2012-2013 Harley Davidson Softail Installation Instructions 1 Power Commander 1 USB Cable 1 CD-ROM 1 Installation Guide 2 Power Commander Decals 2 Dynojet Decals 2 Velcro 1
More informationBA /02/03/04/06/07/08/13/13B/15 BIG AIR KIT (BAK) - Yamaha Road Star (99-07)
BA-2020-00/02/03/04/06/07/08/13/13B/15 BIG AIR KIT (BAK) - Yamaha Road Star (99-07) Page: 1 Revision: 6.2-02/23/2011 Install Time: 1.5 Hours We recommend a qualified Yamaha technician install this kit
More informationMT/FZ-09 O2 controller Mod
kevxtx MT/FZ-09 O2 controller Mod DISCLAIMER: This instruction paper is for informational use. The O2 Controller modification is sold only for race use. The O2 Controller modifies the closed-loop fuel
More informationGASOLINE DIRECT INJECTION IN SI ENGINES B. PAVAN VISWANADH P. ASHOK KUMAR. Mobile No : Mobile No:
GASOLINE DIRECT INJECTION IN SI ENGINES SUBMIT TED BY B. PAVAN VISWANADH P. ASHOK KUMAR Y06ME011, III/IV B. Tech Y06ME003, III/IV B. Tech Pavan.visu@gmail.com ashok.me003@gmail.com Mobile No :9291323516
More informationNEW V FORCE REED CAGES FOR POLARIS ENGINES
NEW V FORCE REED CAGES FOR POLARIS ENGINES Steve Tassinari of Moto Tassinari sent DTR new Vforce3 reed cages that fit the Polaris CFI twins, and asked us to do a back-to-back comparison of stock vs. new
More informationVictor Jr. Plate Upgrade Kits for Square Flange and Dominator Carburetors Kit #70024 and #70025 INSTALLATION INSTRUCTIONS
Victor Jr. Plate Upgrade Kits for Square Flange and Dominator Carburetors Kit #70024 and #70025 INSTALLATION INSTRUCTIONS Please study these instructions carefully before installing your new Edelbrock
More informationSetting up and adjusting SU/Hitachi carbs on the Datsun Roadster by Keith Williams. Service screw
Setting up and adjusting SU/Hitachi carbs on the Datsun Roadster by Keith Williams Service screw This is the service screw it s only use it to raise the engine speed while adjusting the carbs. In normal
More informationFODDER AIR/FUEL. Introducing the latest tools for datalogging your air/fuel ratio and what to do with that valuable information.
AIR/FUEL FODDER Introducing the latest tools for datalogging your air/fuel ratio and what to do with that valuable information. BY EVAN J. SMITH n the current era of performance, one of the toughest challenges
More informationAIR CLEANER RACE KITS
Kit Numbers 91421-99Y, 91420-99Y and 91422-99Y REV. 10-26-00 General These Air Cleaner Race Kits are intended for highperformance racing (OFF ROAD USE) applications only. Use of these kits may reduce or
More informationУрал) - Dnepr (Днепр) Russian Motorcycle Carburetors
Ural (Урал( Урал) - Dnepr (Днепр) Russian Motorcycle Carburetors Part 8A: Adjustment and Overhaul of the Pekar K-65 Carburetors (see also Part 8-8 K-65 Carburetor and Part 8B- Setting Up K-65 K Carbs)
More informationINSTALLATION HYPERCHARGER AIR FILTER KIT 9992
9992 PARTS INCLUDED 1 Chrome Hypercharger Assembly with Chrome Blood Groove Trap Door and Chrome Butterflies 1 Support Bracket 1 Breather Hardware Kit, including: 2 1-1/4 Breather Bolts 2 Breather Hoses
More informationPOWERSPORTS DYNAMOMETER HARDWARE AND SOFTWARE
POWERSPORTS DYNAMOMETER HARDWARE AND SOFTWARE DYNOWARE RT DYNAMOMETER HARDWARE DYNOWARE RT THE NEXT GENERATION OF DYNOJET DYNAMOMETER ELECTRONICS AND SOFTWARE HAS ARRIVED. DynoWare RT is the next generation
More informationENGINE MANAGEMENT SYSTEM. System Sensors
ENGINE MANAGEMENT SYSTEM System Sensors Throttle position sensor - Used to relay throttle position information to the ECU. Throttle opening angle is used by the ECU to determine fuelling and ignition requirements
More informationBasic Requirements. ICE Fuel Metering. Mixture Quality Requirements. Requirements for Metering & Mixing
Basic Requirements ICE Fuel Metering Dr. M. Zahurul Haq Professor Department of Mechanical Engineering Bangladesh University of Engineering & Technology (BUET) Dhaka-1000, Bangladesh zahurul@me.buet.ac.bd
More informationJetting and understanding your CV carburetor
Jetting and understanding your CV carburetor What do all these pieces do? You may also ask, how or why would I do this to my carb? The goal of this article is to unravel the mystery of carburetor jetting
More informationInject Your Horse PART 1, THE PARTS By RYAN MCCORMICK FORDFUELINJECTION.COM Nov 2003
Inject Your Horse PART 1, THE PARTS By RYAN MCCORMICK FORDFUELINJECTION.COM Nov 2003 Fuel Injection, some are asking why again? Well, because many are still intimidated by all this new technology or don
More informationWide Band EFIE Installation Instructions. Locate the wide band oxygen sensor current wire
Wide Band EFIE Installation Instructions Install your fuel efficiency device The EFIE is not intended to be a fuel saver by itself. You should install a device that is designed to get more energy out of
More informationInstallation Guide. Thank you for the purchase of our product. You have just unleashed infinite control, power and ability into your hands.
Installation Guide Thank you for the purchase of our product. You have just unleashed infinite control, power and ability into your hands. This product is for race use only by experienced engine tuners.
More informationCommon Terms Types of Intake Manifolds... 5
INDUCTION SYSTEMS Common Terms... 2 Plenum... 2 Helmholtz Resonator... 2 Intake Runners... 2 Carburetor Spacers... 2 Individual Runners (IR)... 2 Tuned Port... 3 Manifold Heat... 3 Venturi... 3 Booster
More informationSuperTrapp SuperPak. SuperTrapp Makes It Super Easy. efficiently after adding the power upgrades.
Super Trap:Layout 1 5/17/2007 8:58 PM Page 66 R D SuperPak Makes It Super Easy Photos By: Maverick Camera Crew Story By: Tim Wagner In the never ending search for extra power, the roads can lead you in
More informationWARNING! USE ONLY IN RACE OR OTHER CLOSED COURSE APPLICATIONS AND NEVER ON PUBLIC ROADS
2010-2013 Ducati Multistrada 1200 Z-Fi INSTALLATION INSTRUCTIONS P/N F182 WARNING! USE ONLY IN RACE OR OTHER CLOSED COURSE APPLICATIONS AND NEVER ON PUBLIC ROADS Z-Fi products do not meet California CARB
More informationAN EXPLANATION OF CIRCUITS CARTER YH HORIZONTAL CLIMATIC CONTROL CARBURETER
AN EXPLANATION OF CIRCUITS CARTER YH HORIZONTAL CLIMATIC CONTROL CARBURETER The Carter Model YH carbureter may be compared with a Carter YF downdraft carbureter with the circuits rearranged to operate
More informationFuel Metering System Component Description
1999 Chevrolet/Geo Tahoe - 4WD Fuel Metering System Component Description Purpose The function of the fuel metering system is to deliver the correct amount of fuel to the engine under all operating conditions.
More informationTECH INFORMATION EMPI D Performance 2-Barrel Carburetor
TECH INFORMATION EMPI D Performance 2-Barrel Carburetor The New EMPI D 2-Barrel Performance Carburetor.Built specifically for the VW Aftermarket. With all the features that you have asked for More Progression
More informationBRAWLER SERIES CARBURETORS
BRAWLER SERIES CARBURETORS Installation Instructions Please Stop and Read these Instructions before proceeding. If you do not fully understand the installation and tuning instructions you should seek professional
More informationInstallation Instructions for S&S Single Bore Throttle Bodies
Instruction 51-1239 12-29-15 Rev 2 Copyright 2009, 2015 by S&S Cycle, Inc. All rights reserved. Printed in the U.S.A. S&S Cycle, Inc. 14025 Cty Hwy G PO Box 215 Viola, Wisconsin 54664 Phone: 608-627-1497
More informationHonda VTX1800
2801191 Rev 06-28-05 User Manual 2002-2005 Honda VTX1800 Part Number DFCM-1 Congratulations on your purchase of this Dynatek product. Please take a moment to read these instructions completely before installing
More informationPLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
PARTS LIST FUEL AND IGNITION 2012-2014 Harley Davidson Softail Installation Instructions 1 Power Commander 1 USB Cable 1 Installation Guide 2 Power Commander Decals 2 Dynojet Decals 2 Velcro strips 1 Alcohol
More informationArctic Cat M8, M1000, F8, and F1000 Snowmobiles
PARTS LIST 2009-2010 Arctic Cat M8, M1000, F8, and F1000 Snowmobiles Installation Instructions quantity description 1 power commander 1 USB A to mini B cable 1 cd-rom 1 installation guide 2 power commander
More informationINSTALLATION HYPERCHARGER AIR FILTER KIT 9754
9754 PARTS INCLUDED 1 Chrome Hypercharger Assembly 1 Support Bracket 1 Breather Hardware Kit, including: 2 1-1/4 Breather Bolts 2 Breather Hoses 4 Shim Washers 1 Twin Cam Breather Kit, Including: 1 Breather
More informationCAUTION: CAREFULLY READ INSTRUCTIONS BEFORE PROCEEDING. NOT LEGAL FOR USE OR SALE ON POLLUTION CONTROLLED VEHICLES.
Twin Tec Installation Instructions for VRFI D Version Fuel Injection Controller CAUTION: CAREFULLY READ INSTRUCTIONS BEFORE PROCEEDING. T LEGAL FOR USE OR SALE ON POLLUTION CONTROLLED VEHICLES. OVERVIEW
More informationPLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
PARTS LIST 2015 Harley Davidson Street 750 Installation Instructions 1 Power Commander 1 USB Cable 1 Installation Guide 2 Power Commander Decals 2 Dynojet Decals 2 Dual Lock Velcro strips 1 Alcohol swab
More informationHolley High Performance Intake System* For Port 13B Engines (Includes B 6-Port engines converted to 4-Port)
Holley High Performance Intake System* For 1974-1978 4-Port 13B Engines (Includes 1984-85 13B 6-Port engines converted to 4-Port) Installation Instructions I-18038 Note: These instructions assume: The
More informationPLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
PARTS LIST 2007 Harley Davidson Touring Models Installation Instructions 1 Power Commander 1 USB Cable 1 Installation Guide 2 Power Commander Decals 2 Dynojet Decals 2 Zip-ties 2 O2 Optimizers THE IGNITION
More informationWEBER CARBURETOR TROUBLESHOOTING GUIDE
This guide is to help pinpoint problems by diagnosing engine symptoms associated with specific vehicle operating conditions. The chart will guide you step by step to help correct these problems. For successful
More information1 In all circumstances, it can be easily ignited by the spark. 2 The maximum possible amount of chemical energy can be
SIE: Requirements for Metering & Mixing ICE Fuel Metering Dr. Md. Zahurul Haq Professor Department of Mechanical Engineering Bangladesh University of Engineering & Technology (BUET) Dhaka-1000, Bangladesh
More informationPowertrain Efficiency Technologies. Turbochargers
Powertrain Efficiency Technologies Turbochargers Turbochargers increasingly are being used by automakers to make it possible to use downsized gasoline engines that consume less fuel but still deliver the
More informationPhil s Ear Shave Procedure
http://06vn750.blogspot.com/2011/05/ear-shave-procedure-different-format.html 06VN750 Thursday, May 19, 2011 Ear Shave Procedure Phil s Ear Shave Procedure Preface: GENERALLY speaking: If you change the
More informationTRICK FLOW HEADSThree
HEAD GAMES DEPT. TRICK FLOW HEADSThree Part We test more combos, topping 700 horsepower on pump unleaded. STORY + PHOTOS Andy Finkbeiner Our combo works well for both street n strip pump gas duty. Photo:
More informationESS INSTALL. The donor car /6 Cosmos Black/Sand UUC Short Shifter Brembo cross drilled rotors Phillips Nav System 16:9
ESS INSTALL The donor car.. 1997 540/6 Cosmos Black/Sand UUC Short Shifter Brembo cross drilled rotors Phillips Nav System 16:9 The install went in several stages. Disconnect the battery Stage 1 Remove
More information